waitqueue_active() needs smp_mb() to be in sync with waitqueues
modification, but we miss it in io_cqring_ev_posted*() apart from
cq_wait() case.
Take an smb_mb() out of wq_has_sleeper() making it waitqueue_active(),
and place it a few lines before, so it can synchronise other
waitqueue_active() as well.
The patch doesn't add any additional overhead, so even if there are
no problems currently, it's just safer to have it this way.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
CPU0 CPU1
---- ----
lock(&new->fa_lock);
local_irq_disable();
lock(&ctx->completion_lock);
lock(&new->fa_lock);
<Interrupt>
lock(&ctx->completion_lock);
*** DEADLOCK ***
Move kill_fasync() out of io_commit_cqring() to io_cqring_ev_posted(),
so it doesn't hold completion_lock while doing it. That saves from the
reported deadlock, and it's just nice to shorten the locking time and
untangle nested locks (compl_lock -> wq_head::lock).
Reported-by: syzbot+91ca3f25bd7f795f019c@syzkaller.appspotmail.com
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Make sure io_iopoll_complete() tries to wake up eventfd, which currently
is skipped together with io_cqring_ev_posted() for non-SQPOLL IOPOLL.
Add an iopoll version of io_cqring_ev_posted(), duplicates a bit of
code, but they actually use different sets of wait queues may be for
better.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
iommu_flush_dev_iotlb() is called to invalidate caches on a device but
only loops over the devices which are fully-attached to the domain. For
sub-devices, this is ineffective and can result in invalid caching
entries left on the device.
Fix the missing invalidation by adding a loop over the subdevices and
ensuring that 'domain->has_iotlb_device' is updated when attaching to
subdevices.
Fixes: 67b8e02b5e ("iommu/vt-d: Aux-domain specific domain attach/detach")
Signed-off-by: Liu Yi L <yi.l.liu@intel.com>
Acked-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/1609949037-25291-4-git-send-email-yi.l.liu@intel.com
Signed-off-by: Will Deacon <will@kernel.org>
'struct intel_svm' is shared by all devices bound to a give process,
but records only a single pointer to a 'struct intel_iommu'. Consequently,
cache invalidations may only be applied to a single DMAR unit, and are
erroneously skipped for the other devices.
In preparation for fixing this, rework the structures so that the iommu
pointer resides in 'struct intel_svm_dev', allowing 'struct intel_svm'
to track them in its device list.
Fixes: 1c4f88b7f1 ("iommu/vt-d: Shared virtual address in scalable mode")
Cc: Lu Baolu <baolu.lu@linux.intel.com>
Cc: Jacob Pan <jacob.jun.pan@linux.intel.com>
Cc: Raj Ashok <ashok.raj@intel.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Reported-by: Guo Kaijie <Kaijie.Guo@intel.com>
Reported-by: Xin Zeng <xin.zeng@intel.com>
Signed-off-by: Guo Kaijie <Kaijie.Guo@intel.com>
Signed-off-by: Xin Zeng <xin.zeng@intel.com>
Signed-off-by: Liu Yi L <yi.l.liu@intel.com>
Tested-by: Guo Kaijie <Kaijie.Guo@intel.com>
Cc: stable@vger.kernel.org # v5.0+
Acked-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/1609949037-25291-2-git-send-email-yi.l.liu@intel.com
Signed-off-by: Will Deacon <will@kernel.org>
On SM8150 it's occasionally observed that the boot hangs in between the
writing of SMEs and context banks in arm_smmu_device_reset().
The problem seems to coincide with a display refresh happening after
updating the stream mapping, but before clearing - and there by
disabling translation - the context bank picked to emulate translation
bypass.
Resolve this by explicitly disabling the bypass context already in
cfg_probe.
Fixes: f9081b8ff5 ("iommu/arm-smmu-qcom: Implement S2CR quirk")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210106005038.4152731-1-bjorn.andersson@linaro.org
Signed-off-by: Will Deacon <will@kernel.org>
Lock(&iommu->lock) without disabling irq causes lockdep warnings.
========================================================
WARNING: possible irq lock inversion dependency detected
5.11.0-rc1+ #828 Not tainted
--------------------------------------------------------
kworker/0:1H/120 just changed the state of lock:
ffffffffad9ea1b8 (device_domain_lock){..-.}-{2:2}, at:
iommu_flush_dev_iotlb.part.0+0x32/0x120
but this lock took another, SOFTIRQ-unsafe lock in the past:
(&iommu->lock){+.+.}-{2:2}
and interrupts could create inverse lock ordering between them.
other info that might help us debug this:
Possible interrupt unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&iommu->lock);
local_irq_disable();
lock(device_domain_lock);
lock(&iommu->lock);
<Interrupt>
lock(device_domain_lock);
*** DEADLOCK ***
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20201231005323.2178523-5-baolu.lu@linux.intel.com
Signed-off-by: Will Deacon <will@kernel.org>
Drivers are not supposed to use this directly any more.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Link: https://patchwork.freedesktop.org/patch/412156/
Drivers are not supposed to init the page pool directly any more.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Link: https://patchwork.freedesktop.org/patch/412153/
Generate a change uevent when the "number_of_alternate_modes" sysfs file
for partners and plugs is updated by a port driver.
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Benson Leung <bleung@chromium.org>
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Link: https://lore.kernel.org/r/20210107034904.4112029-1-pmalani@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The name of the module for the NVIDIA alt-mode is incorrect as it
looks to be a copy-paste error from the entry above, update it to
the correct typec_nvidia module name.
Cc: Ajay Gupta <ajayg@nvidia.com>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Link: https://lore.kernel.org/r/20210106001605.167917-1-pbrobinson@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enable Super speed plus in configfs to support USB3.1 Gen2.
This ensures that when a USB gadget is plugged in, it is
enumerated as Gen 2 and connected at 10 Gbps if the host and
cable are capable of it.
Many in-tree gadget functions (fs, midi, acm, ncm, mass_storage,
etc.) already have SuperSpeed Plus support.
Tested: plugged gadget into Linux host and saw:
[284907.385986] usb 8-2: new SuperSpeedPlus Gen 2 USB device number 3 using xhci_hcd
Tested-by: Lorenzo Colitti <lorenzo@google.com>
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: taehyun.cho <taehyun.cho@samsung.com>
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Link: https://lore.kernel.org/r/20210106154625.2801030-1-lorenzo@google.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Done opencode in_serving_softirq() checks in in_serving_softirq() to avoid
cluttering the code, hide them in kcov helpers instead.
Fixes: aee9ddb1d3 ("kcov, usb: only collect coverage from __usb_hcd_giveback_urb in softirq")
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Link: https://lore.kernel.org/r/aeb430c5bb90b0ccdf1ec302c70831c1a47b9c45.1609876340.git.andreyknvl@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is observed 'use-after-free' on the dmabuf's file->f_inode with the
race between closing the dmabuf file and reading the dmabuf's debug
info.
Consider the below scenario where P1 is closing the dma_buf file
and P2 is reading the dma_buf's debug info in the system:
P1 P2
dma_buf_debug_show()
dma_buf_put()
__fput()
file->f_op->release()
dput()
....
dentry_unlink_inode()
iput(dentry->d_inode)
(where the inode is freed)
mutex_lock(&db_list.lock)
read 'dma_buf->file->f_inode'
(the same inode is freed by P1)
mutex_unlock(&db_list.lock)
dentry->d_op->d_release()-->
dma_buf_release()
.....
mutex_lock(&db_list.lock)
removes the dmabuf from the list
mutex_unlock(&db_list.lock)
In the above scenario, when dma_buf_put() is called on a dma_buf, it
first frees the dma_buf's file->f_inode(=dentry->d_inode) and then
removes this dma_buf from the system db_list. In between P2 traversing
the db_list tries to access this dma_buf's file->f_inode that was freed
by P1 which is a use-after-free case.
Since, __fput() calls f_op->release first and then later calls the
d_op->d_release, move the dma_buf's db_list removal from d_release() to
f_op->release(). This ensures that dma_buf's file->f_inode is not
accessed after it is released.
Cc: <stable@vger.kernel.org> # 5.4.x-
Fixes: 4ab59c3c63 ("dma-buf: Move dma_buf_release() from fops to dentry_ops")
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Charan Teja Reddy <charante@codeaurora.org>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/1609857399-31549-1-git-send-email-charante@codeaurora.org
For consistency with __uaccess_{disable,enable}_hw_pan(), move the
PSTATE.TCO setting into dedicated __uaccess_{disable,enable}_tco()
functions.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Update Pankaj Sharma as maintainer for mcan mmio device driver as I
will be moving to a different role.
Signed-off-by: Sriram Dash <sriram.dash@samsung.com>
Acked-by: Pankaj Sharma <pankj.sharma@samsung.com>
Link: https://lore.kernel.org/r/20210104123134.16930-1-sriram.dash@samsung.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The previous patch fixes a TEF vs. TX race condition, by first updating the TEF
tail pointer in hardware, and then updating the driver internal pointer.
The same pattern exists in the RX-path, too. This should be no problem, as the
driver accesses the RX-FIFO from the interrupt handler only, thus the access is
properly serialized. Fix the order here, too, so that the TEF- and RX-path look
similar.
Fixes: 1f652bb6ba ("can: mcp25xxfd: rx-path: reduce number of SPI core requests to set UINC bit")
Link: https://lore.kernel.org/r/20210105214138.3150886-3-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The mcp251xfd driver uses a TX FIFO for sending CAN frames and a TX Event FIFO
(TEF) for completed TX-requests.
The TEF event handling in the mcp251xfd_handle_tefif() function has a race
condition. It first increments the tx-ring's tail counter to signal that
there's room in the TX and TEF FIFO, then it increments the TEF FIFO in
hardware.
A running mcp251xfd_start_xmit() on a different CPU might not stop the txqueue
(as the tx-ring still shows free space). The next mcp251xfd_start_xmit() will
push a message into the chip and the TX complete event might overflow the TEF
FIFO.
This patch changes the order to fix the problem.
Fixes: 68c0c1c7f9 ("can: mcp251xfd: tef-path: reduce number of SPI core requests to set UINC bit")
Link: https://lore.kernel.org/r/20210105214138.3150886-2-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
drm/i915 fixes for v5.11-rc3:
- Use per-connector PM QoS tracking for DP aux communication
- GuC firmware fix for older Cometlakes
- Clear the gpu reloc and shadow batches
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/877dop18zf.fsf@intel.com
amd-drm-fixes-5.11-2021-01-06:
amdgpu:
- Telemetry fix for VGH
- Powerplay fixes for RV
- Powerplay fixes for RN
- RAS fixes for Sienna Cichlid
- Blank screen regression fix
- Drop DCN support for aarch64
- Misc other fixes
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210106222721.3934-1-alexander.deucher@amd.com
According to the TCAN4550 datasheet "SLLSF91 - DECEMBER 2018" the tcan4x5x has
the same bittiming constants as a m_can revision 3.2.x/3.3.0.
The tcan4x5x chip I'm using identifies itself as m_can revision 3.2.1, so
remove the tcan4x5x specific bittiming values and rely on the values in the
m_can driver, which are selected according to core revision.
Fixes: 5443c226ba ("can: tcan4x5x: Add tcan4x5x driver to the kernel")
Cc: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Sean Nyekjaer <sean@geanix.com>
Link: https://lore.kernel.org/r/20201215103238.524029-3-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In m_can_class_register() the clock is started, but stopped on exit. When
calling m_can_class_unregister(), the clock is stopped a second time.
This patch removes the erroneous m_can_clk_stop() in m_can_class_unregister().
Fixes: f524f829b7 ("can: m_can: Create a m_can platform framework")
Cc: Dan Murphy <dmurphy@ti.com>
Cc: Sriram Dash <sriram.dash@samsung.com>
Reviewed-by: Sean Nyekjaer <sean@geanix.com>
Link: https://lore.kernel.org/r/20201215103238.524029-2-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
ptp_ines.c uses devm_platform_ioremap_resource(), which is only
built/available when CONFIG_HAS_IOMEM is enabled.
CONFIG_HAS_IOMEM is not enabled for arch/s390/, so builds on S390
have a build error:
s390-linux-ld: drivers/ptp/ptp_ines.o: in function `ines_ptp_ctrl_probe':
ptp_ines.c:(.text+0x17e6): undefined reference to `devm_platform_ioremap_resource'
Prevent builds of ptp_ines.c when HAS_IOMEM is not set.
Fixes: bad1eaa6ac ("ptp: Add a driver for InES time stamping IP core.")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Link: lore.kernel.org/r/202101031125.ZEFCUiKi-lkp@intel.com
Acked-by: Richard Cochran <richardcochran@gmail.com>
Link: https://lore.kernel.org/r/20210106042531.1351-1-rdunlap@infradead.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix build errors when LEDS_CLASS=m and NET_DSA_HIRSCHMANN_HELLCREEK=y.
This limits the latter to =m when LEDS_CLASS=m.
microblaze-linux-ld: drivers/net/dsa/hirschmann/hellcreek_ptp.o: in function `hellcreek_ptp_setup':
(.text+0xf80): undefined reference to `led_classdev_register_ext'
microblaze-linux-ld: (.text+0xf94): undefined reference to `led_classdev_register_ext'
microblaze-linux-ld: drivers/net/dsa/hirschmann/hellcreek_ptp.o: in function `hellcreek_ptp_free':
(.text+0x1018): undefined reference to `led_classdev_unregister'
microblaze-linux-ld: (.text+0x1024): undefined reference to `led_classdev_unregister'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Link: lore.kernel.org/r/202101060655.iUvMJqS2-lkp@intel.com
Cc: Kurt Kanzenbach <kurt@linutronix.de>
Link: https://lore.kernel.org/r/20210106021815.31796-1-rdunlap@infradead.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
.dellink does not get called after .newlink fails,
bareudp_newlink() must undo what bareudp_configure()
has done if bareudp_link_config() fails.
v2: call bareudp_dellink(), like bareudp_dev_create() does
Fixes: 571912c69f ("net: UDP tunnel encapsulation module for tunnelling different protocols like MPLS, IP, NSH etc.")
Link: https://lore.kernel.org/r/20210105190725.1736246-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The error message says that "Jumbo frames are not supported on XDP", but
the code checks for mtu > MVNETA_MAX_RX_BUF_SIZE, not mtu > 1500.
Fix this error message.
Signed-off-by: Marek Behún <kabel@kernel.org>
Fixes: 0db51da7a8 ("net: mvneta: add basic XDP support")
Cc: Lorenzo Bianconi <lorenzo@kernel.org>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Link: https://lore.kernel.org/r/20210105172333.21613-1-kabel@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
For older glibc ~2.17, #include'ing both linux/if.h and net/if.h
fails due to complaints about redefinition of interface flags:
CC net.o
In file included from net.c:13:0:
/usr/include/linux/if.h:71:2: error: redeclaration of enumerator ‘IFF_UP’
IFF_UP = 1<<0, /* sysfs */
^
/usr/include/net/if.h:44:5: note: previous definition of ‘IFF_UP’ was here
IFF_UP = 0x1, /* Interface is up. */
The issue was fixed in kernel headers in [1], but since compilation
of net.c picks up system headers the problem can recur.
Dropping #include <linux/if.h> resolves the issue and it is
not needed for compilation anyhow.
[1] https://lore.kernel.org/netdev/1461512707-23058-1-git-send-email-mikko.rapeli__34748.27880641$1462831734$gmane$org@iki.fi/
Fixes: f6f3bac08f ("tools/bpf: bpftool: add net support")
Signed-off-by: Alan Maguire <alan.maguire@oracle.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/1609948746-15369-1-git-send-email-alan.maguire@oracle.com
Fedora Rawhide has started including gcc 11,and the g++ compiler
throws a wobbly when it hits scripts/gcc-plugins:
HOSTCXX scripts/gcc-plugins/latent_entropy_plugin.so
In file included from /usr/include/c++/11/type_traits:35,
from /usr/lib/gcc/x86_64-redhat-linux/11/plugin/include/system.h:244,
from /usr/lib/gcc/x86_64-redhat-linux/11/plugin/include/gcc-plugin.h:28,
from scripts/gcc-plugins/gcc-common.h:7,
from scripts/gcc-plugins/latent_entropy_plugin.c:78:
/usr/include/c++/11/bits/c++0x_warning.h:32:2: error: #error This file requires compiler and library support for the ISO
C++ 2011 standard. This support must be enabled with the -std=c++11 or -std=gnu++11 compiler options.
32 | #error This file requires compiler and library support \
In fact, it works just fine with c++11, which has been in gcc since 4.8,
and we now require 4.9 as a minimum.
Signed-off-by: Valdis Kletnieks <valdis.kletnieks@vt.edu>
Acked-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/82487.1609006918@turing-police
This reverts commit a135a1b4c4.
This leads to blank screens on some boards after replugging a
display. Revert until we understand the root cause and can
fix both the leak and the blank screen after replug.
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=211033
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1427
Cc: Stylon Wang <stylon.wang@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Cc: Andre Tomt <andre@tomt.net>
Cc: Oleksandr Natalenko <oleksandr@natalenko.name>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
From Ard:
"Simply disabling -mgeneral-regs-only left and right is risky, given that
the standard AArch64 ABI permits the use of FP/SIMD registers anywhere,
and GCC is known to use SIMD registers for spilling, and may invent
other uses of the FP/SIMD register file that have nothing to do with the
floating point code in question. Note that putting kernel_neon_begin()
and kernel_neon_end() around the code that does use FP is not sufficient
here, the problem is in all the other code that may be emitted with
references to SIMD registers in it.
So the only way to do this properly is to put all floating point code in
a separate compilation unit, and only compile that unit with
-mgeneral-regs-only."
Disable support until the code can be properly refactored to support this
properly on aarch64.
Acked-by: Will Deacon <will@kernel.org>
Reported-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
added I2C address and asic support flag
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: John Clements <john.clements@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
old code wrongly used the bad page status as the function return value,
which cause amdgpu_ras_badpages_read always return failed.
Signed-off-by: Dennis Li <Dennis.Li@amd.com>
Reviewed-by: Guchun Chen <guchun.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Navi12 HDCP & DTM deinitialization needs continue to free bo if already
created though initialized flag is not set.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Jiawei Gu <Jiawei.Gu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Some of the newly added code is hidden inside of #ifdef
blocks, but one variable is unused when debugfs is disabled:
drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm.c:8370:8: error: unused variable 'configure_crc' [-Werror,-Wunused-variable]
Change the #ifdef to an if(IS_ENABLED()) check to fix the warning
and avoid adding more #ifdefs.
Fixes: c920888c60 ("drm/amd/display: Expose new CRC window property")
Reviewed-by: Wayne Lin <Wayne.Lin@amd.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch is to improve the fine grain tuning function for RV/RV2/PCO.
The fine grain tuning function uses the sysfs node -- pp_od_clk_voltage
to config gfxclk. Meanwhile, another sysfs
node -- power_dpm_force_perfomance_level also affects the gfx clk.
It will cause confusion when these two sysfs nodes works
together. So this patch adds one flag to avoid this confusion, the flag
will make these two sysfs nodes work separately.
The flag is set as "disabled" by default, so the fine grain tuning function
will be disabled by default.
Only when power_dpm_force_perfomance_level is changed to
"manual" mode, the flag will be set as "enabled",
and the fine grain tuning function will be enabled.
In other profile modes, including "auto", "high", "low",
"profile_peak", "profile_standard", "profile_min_sclk",
"profile_min_mclk", the flag will be set as "disabled",
and the od range of fine grain tuning function will
be restored default value.
Signed-off-by: Xiaojian Du <Xiaojian.Du@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch is to fix the failure when change power profile to
"profile_peak" for renoir.
Signed-off-by: Xiaojian Du <Xiaojian.Du@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When GFXOFF is enabled and GPU is idle, driver will fail to access some
registers. Therefore change to disable power gating before all access
registers with MMIO.
Dmesg log is as following:
amdgpu 0000:03:00.0: amdgpu: amdgpu: finishing device.
amdgpu: cp queue pipe 4 queue 0 preemption failed
amdgpu 0000:03:00.0: amdgpu: failed to write reg 2890 wait reg 28a2
amdgpu 0000:03:00.0: amdgpu: failed to write reg 1a6f4 wait reg 1a706
amdgpu 0000:03:00.0: amdgpu: failed to write reg 2890 wait reg 28a2
amdgpu 0000:03:00.0: amdgpu: failed to write reg 1a6f4 wait reg 1a706
Signed-off-by: Dennis Li <Dennis.Li@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
global noretry setting is cached to gmc.noretry
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
sienna cichlid interfaces with RAS eeprom on I2C controller port 1
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: John Clements <john.clements@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch is to improve the fine grain tuning function for RV/RV2/PCO.
This patch adds two new commands: "restore" and "commit".
This function uses the pp_od_clk_voltage sysfs file to configure the min
and max value of gfx clock frequency manually or restore the default value.
Command guide:
echo "s level value" > pp_od_clk_voltage
"s" - set the sclk frequency
"level" - 0 or 1, "0" represents the min value, "1" represents
the max value
"value" - the target value of sclk frequency, it should be limited in the
safe range
echo "r" > pp_od_clk_voltage
"r" - reset the sclk frequency, restore the default value instantly
echo "c" > pp_od_clk_voltage
"c" - commit the min and max value of sclk frequency to the system
only after the commit command, the target values set by "s" command
will take effect.
Example:
1)change power profile from "auto" to "manual"
$ cat power_dpm_force_performance_level
auto
$ echo "manual" > power_dpm_force_performance_level
$ cat power_dpm_force_performance_level
manual
2)check the default sclk frequency
$ cat pp_od_clk_voltage
OD_SCLK:
0: 200Mhz
1: 1400Mhz
OD_RANGE:
SCLK: 200MHz 1400MHz
3)use "s" -- set command to configure the min and max sclk frequency
$ echo "s 0 600" > pp_od_clk_voltage
$ echo "s 1 1000" > pp_od_clk_voltage
$ echo "c" > pp_od_clk_voltage
$ cat pp_od_clk_voltage
OD_SCLK:
0: 600Mhz
1: 1000Mhz
OD_RANGE:
SCLK: 200MHz 1400MHz
4)use "r" -- reset command to restore the min or max sclk frequency
$ echo "r" > pp_od_clk_voltage
$ cat pp_od_clk_voltage
OD_SCLK:
0: 200Mhz
1: 1400Mhz
OD_RANGE:
SCLK: 200MHz 1400MHz
Signed-off-by: Xiaojian Du <Xiaojian.Du@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch is to correct the sensor value of power for vangogh.
Signed-off-by: Xiaojian Du <Xiaojian.Du@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
-----BEGIN PGP SIGNATURE-----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=jlQf
-----END PGP SIGNATURE-----
Merge tag 'for-5.11-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
"A few more fixes that arrived before the end of the year:
- a bunch of fixes related to transaction handle lifetime wrt various
operations (umount, remount, qgroup scan, orphan cleanup)
- async discard scheduling fixes
- fix item size calculation when item keys collide for extend refs
(hardlinks)
- fix qgroup flushing from running transaction
- fix send, wrong file path when there is an inode with a pending
rmdir
- fix deadlock when cloning inline extent and low on free metadata
space"
* tag 'for-5.11-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: run delayed iputs when remounting RO to avoid leaking them
btrfs: add assertion for empty list of transactions at late stage of umount
btrfs: fix race between RO remount and the cleaner task
btrfs: fix transaction leak and crash after cleaning up orphans on RO mount
btrfs: fix transaction leak and crash after RO remount caused by qgroup rescan
btrfs: merge critical sections of discard lock in workfn
btrfs: fix racy access to discard_ctl data
btrfs: fix async discard stall
btrfs: tests: initialize test inodes location
btrfs: send: fix wrong file path when there is an inode with a pending rmdir
btrfs: qgroup: don't try to wait flushing if we're already holding a transaction
btrfs: correctly calculate item size used when item key collision happens
btrfs: fix deadlock when cloning inline extent and low on free metadata space
This contains a few fixes for iMX and Qualcomm drivers and also
updates my email to my kernel.org address.
- qcom: Fix rpmh link failures when compile test is enabled
- imx: Add a missing of_node_put after of_device_is_available
- imx: Remove a useless test
- imx8mq: Use icc_sync_state
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
-----BEGIN PGP SIGNATURE-----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=0DvY
-----END PGP SIGNATURE-----
Merge tag 'icc-5.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/djakov/icc into char-misc-linus
Georgi writes:
interconnect fixes for v5.11
This contains a few fixes for iMX and Qualcomm drivers and also
updates my email to my kernel.org address.
- qcom: Fix rpmh link failures when compile test is enabled
- imx: Add a missing of_node_put after of_device_is_available
- imx: Remove a useless test
- imx8mq: Use icc_sync_state
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
* tag 'icc-5.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/djakov/icc:
MAINTAINERS: Update Georgi's email address
interconnect: imx8mq: Use icc_sync_state
interconnect: imx: Remove a useless test
interconnect: imx: Add a missing of_node_put after of_device_is_available
interconnect: qcom: fix rpmh link failures
