This fix the following warnings detect with make W=1 C=1:
drivers/bluetooth/btusb.c:2212:9: warning: cast to restricted __le16
drivers/bluetooth/btusb.c:2212:9: warning: cast to restricted __le16
drivers/bluetooth/btusb.c:2245:18: warning: cast to restricted __le16
drivers/bluetooth/btusb.c:2249:18: warning: cast to restricted __le16
drivers/bluetooth/btusb.c:2253:18: warning: cast to restricted __le16
drivers/bluetooth/btusb.c:2257:18: warning: cast to restricted __le16
drivers/bluetooth/btusb.c:2261:18: warning: cast to restricted __le16
drivers/bluetooth/btusb.c:2267:18: warning: cast to restricted __le16
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
RTL8723DS is another variant of the RTL8723 WiFi + Bluetooth chip. It is
already supported by the hci_uart/btrtl driver. Document the compatible.
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Alistair Francis <alistair@alistair23.me>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Document the compatible string for BCM43430A0 bluetooth used in lg-lenok
and BCM43430A1 used in asus-sparrow.
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
pci_disable_device() need be called while module exiting, switch to use
pcim_enable(), pci_disable_device() will be called in pcim_release()
after probe() failure.
Fixes: ab80b2cec05f ("Bluetooth: hci_bcm4377: Add new driver for BCM4377 PCIe boards")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Sven Peter <sven@svenpeter.dev>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Broadcom BCM4377/4378/4387 are dual WiFi/Bluetooth boards found in Apple
machines. This driver adds support for the Bluetooth function which
exposes a shared memory IPC protocol over PCIe to tunnel HCI traffic.
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Broadcom 4377 controllers found in Apple x86 Macs with the T2 chip
claim to support extended scanning when querying supported states,
< HCI Command: LE Read Supported St.. (0x08|0x001c) plen 0
> HCI Event: Command Complete (0x0e) plen 12
LE Read Supported States (0x08|0x001c) ncmd 1
Status: Success (0x00)
States: 0x000003ffffffffff
[...]
LE Set Extended Scan Parameters (Octet 37 - Bit 5)
LE Set Extended Scan Enable (Octet 37 - Bit 6)
[...]
, but then fail to actually implement the extended scanning:
< HCI Command: LE Set Extended Sca.. (0x08|0x0041) plen 8
Own address type: Random (0x01)
Filter policy: Accept all advertisement (0x00)
PHYs: 0x01
Entry 0: LE 1M
Type: Active (0x01)
Interval: 11.250 msec (0x0012)
Window: 11.250 msec (0x0012)
> HCI Event: Command Complete (0x0e) plen 4
LE Set Extended Scan Parameters (0x08|0x0041) ncmd 1
Status: Unknown HCI Command (0x01)
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Broadcom controllers present on Apple Silicon devices use the upper
8 bits of the event type in the LE Extended Advertising Report for
the channel on which the frame has been received.
These bits are reserved according to the Bluetooth spec anyway such that
we can just drop them to ensure that the advertising results are parsed
correctly.
The following excerpt from a btmon trace shows a report received on
channel 37 by these controllers:
> HCI Event: LE Meta Event (0x3e) plen 55
LE Extended Advertising Report (0x0d)
Num reports: 1
Entry 0
Event type: 0x2513
Props: 0x0013
Connectable
Scannable
Use legacy advertising PDUs
Data status: Complete
Reserved (0x2500)
Legacy PDU Type: Reserved (0x2513)
Address type: Public (0x00)
Address: XX:XX:XX:XX:XX:XX (Shenzhen Jingxun Software [...])
Primary PHY: LE 1M
Secondary PHY: No packets
SID: no ADI field (0xff)
TX power: 127 dBm
RSSI: -76 dBm (0xb4)
Periodic advertising interval: 0.00 msec (0x0000)
Direct address type: Public (0x00)
Direct address: 00:00:00:00:00:00 (OUI 00-00-00)
Data length: 0x1d
[...]
Flags: 0x18
Simultaneous LE and BR/EDR (Controller)
Simultaneous LE and BR/EDR (Host)
Company: Harman International Industries, Inc. (87)
Data: [...]
Service Data (UUID 0xfddf):
Name (complete): JBL Flip 5
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Add bluetooth controller nodes and the required brcm,board-type
properties to be able to select the correct firmware to all board
device trees.
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
These chips are combined Wi-Fi/Bluetooth radios which expose a
PCI subfunction for the Bluetooth part.
They are found in Apple machines such as the x86 models with the T2
chip or the arm64 models with the M1 or M2 chips.
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Bluetooth controllers share the common local-bd-address property.
Add a generic YAML schema to replace bluetooth.txt for those.
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
CYW4373A0 is a Wi-Fi + Bluetooth combo device from Cypress.
This chip is present e.g. on muRata 2AE module.
This chip has additional quirk where the HCI command 0xfc45, used on
older chips to switch UART clock from 24 MHz to 48 MHz, to support
baudrates over 3 Mbdps, is no longer recognized by this newer chip.
This newer chip can configure the 4 Mbdps baudrate without the need
to issue HCI command 0xfc45, so add flag to indicate this and do not
issue the command on this chip to avoid failure to set 4 Mbdps baud
rate.
It is not clear whether there is a way to determine which chip does
and which chip does not support the HCI command 0xfc45, other than
trial and error.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
CYW4373A0 is a Wi-Fi + Bluetooth combo device from Cypress.
This chip is present e.g. on muRata 2AE module. Extend the
binding with its DT compatible.
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Replace kmalloc+memset by kzalloc
for better readability and simplicity.
This addresses the cocci warning below:
WARNING: kzalloc should be used for d, instead of kmalloc/memset
Signed-off-by: Kang Minchul <tegongkang@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Add IDs to usb_device_id table for WCN6855. IDs are extracted from Windows
driver of Lenovo Thinkpad T14 Gen 2(Driver version 1.0.0.1205 Windows 10)
Windows driver download address:
https://pcsupport.lenovo.com/us/en/products/laptops-and-netbooks/
thinkpad-t-series-laptops/thinkpad-t14-gen-2-type-20xk-20xl/downloads
/driver-list/
Signed-off-by: Shengyu Qu <wiagn233@outlook.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
'err' is known to be <0 at this point.
So, some cases can not be reached because of a missing "-".
Add it.
Fixes: ca2045e059 ("Bluetooth: Add bt_status")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This adds CONFIG_BT_LE_L2CAP_ECRED which can be used to enable L2CAP
Enhanced Credit Flow Control Mode by default, previously it was only
possible to set it via module parameter (e.g. bluetooth.enable_ecred=1).
Since L2CAP ECRED mode is required by the likes of EATT which is
recommended for LE Audio this enables it by default.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Tested-By: Tedd Ho-Jeong An <tedd.an@intel.com>
poll_sync has been proven to fix races of USB data and event endpoints
so this enables it by default.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Tested-by: Tedd Ho-Jeong An <tedd.an@intel.com>
This adds CONFIG_BT_HCIBTUSB_POLL_SYNC which can be used to set the
default behavior of Bluetooth USB controller with respect to poll
synchronization of its endpoits.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Tested-by: Tedd Ho-Jeong An <tedd.an@intel.com>
The current version of the configuration structure has unaligned
16-bit fields, but according to the specification [1], access to
the configuration space must be aligned.
Add a second, aligned version of the configuration structure
and a new feature bit indicating that this version is being used.
[1] https://docs.oasis-open.org/virtio/virtio/v1.1/virtio-v1.1.pdf
Signed-off-by: Igor Skalkin <Igor.Skalkin@opensynergy.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
When validating the parameter length for MGMT_OP_ADD_EXT_ADV_PARAMS
command, use the correct op code in error status report:
was MGMT_OP_ADD_ADVERTISING, changed to MGMT_OP_ADD_EXT_ADV_PARAMS.
Fixes: 1241057283 ("Bluetooth: Break add adv into two mgmt commands")
Signed-off-by: Inga Stotland <inga.stotland@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
If hci_register_suspend_notifier() returns error, the hdev and rfkill
are leaked. We could disregard the error and print a warning message
instead to avoid leaks, as it just means we won't be handing suspend
requests.
Fixes: 9952d90ea2 ("Bluetooth: Handle PM_SUSPEND_PREPARE and PM_POST_SUSPEND")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Use kzalloc rather than duplicating its implementation, which makes code
simple and easy to understand.
./net/bluetooth/hci_conn.c:2038:6-13: WARNING: kzalloc should be used for cp, instead of kmalloc/memset.
Link: https://bugzilla.openanolis.cn/show_bug.cgi?id=2406
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Only assign hdev->wakeup if the serial port supports wakeup. Otherwise
it will fall back to the hci_uart_wakeup or the behavior that can be
overridden before calling the hci_uart_register_device().
Signed-off-by: Zhengping Jiang <jiangzp@google.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
For ISO BIS related functions in hci_conn.c, make dst_type values be HCI
address type values, not ISO socket address type values. This makes it
consistent with CIS functions.
Signed-off-by: Pauli Virtanen <pav@iki.fi>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
For USB ALT 6 settings some Realtek chips need to transmit mSBC data
continuously without the zero length of USB packets.
In this commit, create BTUSB_ALT6_CONTINUOUS_TX to manage the behavior.
Therefore, create REALTEK_ALT6_CONTINUOUS_TX_CHIP to manage the specific
chip model for the behavior.
Signed-off-by: Max Chou <max.chou@realtek.com>
Signed-off-by: Hilda Wu <hildawu@realtek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This patch adds a data structure for btrealtek object, and the
definition of vendor behavior flags. It also adds macros to set/test/get
the flags.
Signed-off-by: Hilda Wu <hildawu@realtek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Device removal is clearly out of virtio spec: it attempts to remove
unused buffers from a VQ before invoking device reset. To fix, make
open/close NOPs and do all cleanup/setup in probe/remove.
NB: This is a hacky way to handle this - virtbt_{open,close} as NOP is
not really what a driver is supposed to be doing. These are transport
enable/disable callbacks from the BT core towards the driver. It maps to
a device being enabled/disabled by something like bluetoothd for
example. So if disabled, users expect that no resources/queues are in
use. It does work with all other transports like USB, SDIO, UART etc.
There should be no buffer used if the device is powered off. We also
don’t have any USB URBs in-flight if the transport is not active.
The way to implement a proper fix would be using vq reset if supported,
or even using a full device reset.
The cost of the hack is a single skb wasted on an unused bt device.
NB2: with this fix in place driver still suffers from a race condition
if an interrupt triggers while device is being reset. To fix, in the
virtbt_close() callback we should deactivate all interrupts. To be
fixed.
squashed fixup: bluetooth: virtio_bt: fix an error code in probe()
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20220811080943.198245-1-mst@redhat.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Tested-by: Igor Skalkin <Igor.Skalkin@opensynergy.com>
If a command is already sent, we take care of freeing it, but we
also need to cancel the timeout as well.
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@google.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
force_static_address shall be writable while hdev is initing but is not
considered powered yet since the static address is written only when
powered.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Tested-by: Brian Gix <brian.gix@intel.com>
This attempts to program the address stored in hdev->static_addr after
the init sequence has been complete:
@ MGMT Command: Set Static A.. (0x002b) plen 6
Address: C0:55:44:33:22:11 (Static)
@ MGMT Event: Command Complete (0x0001) plen 7
Set Static Address (0x002b) plen 4
Status: Success (0x00)
Current settings: 0x00008200
Low Energy
Static Address
@ MGMT Event: New Settings (0x0006) plen 4
Current settings: 0x00008200
Low Energy
Static Address
< HCI Command: LE Set Random.. (0x08|0x0005) plen 6
Address: C0:55:44:33:22:11 (Static)
> HCI Event: Command Complete (0x0e) plen 4
LE Set Random Address (0x08|0x0005) ncmd 1
Status: Success (0x00)
@ MGMT Event: Command Complete (0x0001) plen 7
Set Powered (0x0005) plen 4
Status: Success (0x00)
Current settings: 0x00008201
Powered
Low Energy
Static Address
@ MGMT Event: New Settings (0x0006) plen 4
Current settings: 0x00008201
Powered
Low Energy
Static Address
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Tested-by: Brian Gix <brian.gix@intel.com>
The USB interface between the host and the bluetooth adapter used for
SCO packets uses an USB isochronous endpoint with a fragmentation scheme
that does not tolerate errors. Except USB isochronous transfers do
not provide a reliable stream with guaranteed delivery. (There is no
retry on error, see USB spec v2.0 5.6 and 8.5.5.)
To fragment a packet, the bluetooth HCI simply splits it in parts and
transfer them as-is. The receiver is expected to reconstruct the packet
by assuming the first fragment contains the header and parsing its size
field. There is no error detection either.
If a fragment is lost, the end result is that the kernel is no longer
synchronized and will pass malformed data to the upper layers, since it
has no way to tell if the first fragment is an actual first fragment or
a continuation fragment. Resynchronization can only happen by luck and
requires an unbounded amount of time.
The typical symptom for a HSP/HFP bluetooth headset is that the
microphone stops working and dmesg contains piles of rate-limited
"Bluetooth: hci0: SCO packet for unknown connection handle XXXX"
errors for an indeterminate amount of time, until the kernel accidentally
resynchronize.
A workaround is to ask the upper layer to prevalidate the first fragment
header. This is not possible with user channels so this workaround is
disabled in this case.
This problem is the most severe when using an ath3k adapter on an i.MX 6
board, where packet loss occur regularly, possibly because it is an USB1
device connected on an USB2 hub and this is a special case requiring
split transactions.
Signed-off-by: Nicolas Cavallari <nicolas.cavallari@green-communications.fr>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
On cmd_timeout with no reset_gpio, reset the USB port as a last
resort.
This patch changes the behavior of btusb_intel_cmd_timeout and
btusb_rtl_cmd_timeout.
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@google.com>
Reviewed-by: Ying Hsu <yinghsu@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
In case of suspend/resume and HCI_RESET (BT On and Off),
ISOC endpoint set to alt setting 0 when no SCO connection exists.
This patch shall avoid resetting of ISOC endpoint to alt setting to 0.
Signed-off-by: Chethan Tumkur Narayan <chethan.tumkur.narayan@intel.com>
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Taras's Marvell email account will be shut down soon so change it to Plvision.
Signed-off-by: Taras Chornyi <taras.chornyi@plvision.eu>
Signed-off-by: Vadym Kochan <vadym.kochan@plvision.eu>
Link: https://lore.kernel.org/r/20221209154521.1246881-1-vadym.kochan@plvision.eu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The implementation of strscpy() is more robust and safer.
That's now the recommended way to copy NUL terminated strings.
Signed-off-by: Xu Panda <xu.panda@zte.com.cn>
Signed-off-by: Yang Yang <yang.yang29@zte.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://lore.kernel.org/r/202212091538591375035@zte.com.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Recently, a customer reported that from their container whose
net namespace is different to the host's init_net, they can't set
the container's net.sctp.rto_max to any value smaller than
init_net.sctp.rto_min.
For instance,
Host:
sudo sysctl net.sctp.rto_min
net.sctp.rto_min = 1000
Container:
echo 100 > /mnt/proc-net/sctp/rto_min
echo 400 > /mnt/proc-net/sctp/rto_max
echo: write error: Invalid argument
This is caused by the check made from this'commit 4f3fdf3bc5
("sctp: add check rto_min and rto_max in sysctl")'
When validating the input value, it's always referring the boundary
value set for the init_net namespace.
Having container's rto_max smaller than host's init_net.sctp.rto_min
does make sense. Consider that the rto between two containers on the
same host is very likely smaller than it for two hosts.
So to fix this problem, as suggested by Marcelo, this patch makes the
extra pointers of rto_min, rto_max, pf_retrans, and ps_retrans point
to the corresponding variables from the newly created net namespace while
the new net namespace is being registered in sctp_sysctl_net_register.
Fixes: 4f3fdf3bc5 ("sctp: add check rto_min and rto_max in sysctl")
Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Firo Yang <firo.yang@suse.com>
Link: https://lore.kernel.org/r/20221209054854.23889-1-firo.yang@suse.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fourth set of patches for v6.2. Few final patches, a big change is
that rtw88 now has USB support.
Major changes:
rtw88
* support USB devices rtw8821cu, rtw8822bu, rtw8822cu and rtw8723du
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmOW9EsRHGt2YWxvQGtl
cm5lbC5vcmcACgkQbhckVSbrbZup1wf9EO1wK3M+wICOthV9hphaMK/cU5XQe455
V27N+IGg3KkeLgERYj/35C1Xwa4vXeUxWN31KvNJ/51IQaM14NfUE3OOu+gqUO36
a/HhECtcmzsjC+22hH1gvnN73/+S8VQEEfOJ//Jcg6exRmXVKRMWZU1o3rFupAR+
qePWzvYuadobmE8G/Zq2VFB5Eouf5z7MSXLd7Y/8HJMdL812GmA0nhNJXhHDt27A
/K5QBOSnRQ24ZLOG4P0eFZrJGqFTcI27+w4bv+rzUL2ME/Rgp1hB7wBwQbCwD8sU
Aus05avcIcVNfsTk3z7kOnYiBqf08WX6Ng6ezb9HunXXfWhLW7JtAw==
=AzL1
-----END PGP SIGNATURE-----
Merge tag 'wireless-next-2022-12-12' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Kalle Valo says:
====================
wireless-next patches for v6.2
Fourth set of patches for v6.2. Few final patches, a big change is
that rtw88 now has USB support.
Major changes:
rtw88
* support USB devices rtw8821cu, rtw8822bu, rtw8822cu and rtw8723du
* tag 'wireless-next-2022-12-12' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (43 commits)
wifi: rtl8xxxu: fixing IQK failures for rtl8192eu
wifi: rtlwifi: btcoexist: fix conditions branches that are never executed
wifi: rtlwifi: rtl8192se: remove redundant rtl_get_bbreg() call
wifi: rtw88: Add rtw8723du chipset support
wifi: rtw88: Add rtw8822cu chipset support
wifi: rtw88: Add rtw8822bu chipset support
wifi: rtw88: Add rtw8821cu chipset support
wifi: rtw88: Add common USB chip support
wifi: rtw88: iterate over vif/sta list non-atomically
wifi: rtw88: Drop coex mutex
wifi: rtw88: Drop h2c.lock
wifi: rtw88: Drop rf_lock
wifi: rtw88: Call rtw_fw_beacon_filter_config() with rtwdev->mutex held
wifi: rtw88: print firmware type in info message
wifi: rtw89: add join info upon create interface
wifi: rtw89: fix unsuccessful interface_add flow
wifi: rtw89: stop mac port function when stop_ap()
wifi: rtw89: add mac TSF sync function
wifi: rtw89: request full firmware only once if it's early requested
wifi: rtw89: don't request partial firmware if SECURITY_LOADPIN_ENFORCE
...
====================
Link: https://lore.kernel.org/r/20221212093026.5C5AEC433D2@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=fzwv
-----END PGP SIGNATURE-----
Merge tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next
Alexei Starovoitov says:
====================
pull-request: bpf-next 2022-12-11
We've added 74 non-merge commits during the last 11 day(s) which contain
a total of 88 files changed, 3362 insertions(+), 789 deletions(-).
The main changes are:
1) Decouple prune and jump points handling in the verifier, from Andrii.
2) Do not rely on ALLOW_ERROR_INJECTION for fmod_ret, from Benjamin.
Merged from hid tree.
3) Do not zero-extend kfunc return values. Necessary fix for 32-bit archs,
from Björn.
4) Don't use rcu_users to refcount in task kfuncs, from David.
5) Three reg_state->id fixes in the verifier, from Eduard.
6) Optimize bpf_mem_alloc by reusing elements from free_by_rcu, from Hou.
7) Refactor dynptr handling in the verifier, from Kumar.
8) Remove the "/sys" mount and umount dance in {open,close}_netns
in bpf selftests, from Martin.
9) Enable sleepable support for cgrp local storage, from Yonghong.
* tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (74 commits)
selftests/bpf: test case for relaxed prunning of active_lock.id
selftests/bpf: Add pruning test case for bpf_spin_lock
bpf: use check_ids() for active_lock comparison
selftests/bpf: verify states_equal() maintains idmap across all frames
bpf: states_equal() must build idmap for all function frames
selftests/bpf: test cases for regsafe() bug skipping check_id()
bpf: regsafe() must not skip check_ids()
docs/bpf: Add documentation for BPF_MAP_TYPE_SK_STORAGE
selftests/bpf: Add test for dynptr reinit in user_ringbuf callback
bpf: Use memmove for bpf_dynptr_{read,write}
bpf: Move PTR_TO_STACK alignment check to process_dynptr_func
bpf: Rework check_func_arg_reg_off
bpf: Rework process_dynptr_func
bpf: Propagate errors from process_* checks in check_func_arg
bpf: Refactor ARG_PTR_TO_DYNPTR checks into process_dynptr_func
bpf: Skip rcu_barrier() if rcu_trace_implies_rcu_gp() is true
bpf: Reuse freed element in free_by_rcu during allocation
selftests/bpf: Bring test_offload.py back to life
bpf: Fix comment error in fixup_kfunc_call function
bpf: Do not zero-extend kfunc return values
...
====================
Link: https://lore.kernel.org/r/20221212024701.73809-1-alexei.starovoitov@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEBsvAIBsPu6mG7thcrX5LkNig010FAmOXCo0THG1rbEBwZW5n
dXRyb25peC5kZQAKCRCtfkuQ2KDTXUD/B/4m3F/FIpfQjrLR8P/87hkHtu1vLnPV
uo7SGVmq8aDiMRqWSLBWkiP6ceGememckrplG+qprx9QVZhagbtFN1/kE9jXxYSU
s+hh4ARmLfpdZmcNCFzFi2S68G4fsQ3rTI8g/itbpQYCGyHt90yA5+PqT+QQZOvo
J4l4uim4nVyBNEW136Vf13K0iFCmeJr4zr1eSqqHhZVSbK2cQSSN93HlhmZ+ccjT
c1vZdNL1nd9mCQkNFHC+JPehfcgaI0r6hx8RYECvOCy8EbK1ZXdseWlM/z7IoxZm
DiT2KhTao9xa9qcnRjI6oqTwO0omlqND2YDBj+SRwfFAs3HogeOaQjRT
=w/j3
-----END PGP SIGNATURE-----
Merge tag 'linux-can-next-for-6.2-20221212' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
linux-can-next-for-6.2-20221212
this is a pull request of 39 patches for net-next/master.
The first 2 patches are by me fix a warning and coding style in the
kvaser_usb driver.
Vivek Yadav's patch sorts the includes of the m_can driver.
Biju Das contributes 5 patches for the rcar_canfd driver improve the
support for different IP core variants.
Jean Delvare's patch for the ctucanfd drops the dependency on
COMPILE_TEST.
Vincent Mailhol's patch sorts the includes of the etas_es58x driver.
Haibo Chen's contributes 2 patches that add i.MX93 support to the
flexcan driver.
Lad Prabhakar's patch updates the dt-bindings documentation of the
rcar_canfd driver.
Minghao Chi's patch converts the c_can platform driver to
devm_platform_get_and_ioremap_resource().
In the next 7 patches Vincent Mailhol adds devlink support to the
etas_es58x driver to report firmware, bootloader and hardware version.
Xu Panda's patch converts a strncpy() -> strscpy() in the ucan driver.
Ye Bin's patch removes a useless parameter from the AF_CAN protocol.
The next 2 patches by Vincent Mailhol and remove unneeded or unused
pointers to struct usb_interface in device's priv struct in the ucan
and gs_usb driver.
Vivek Yadav's patch cleans up the usage of the RAM initialization in
the m_can driver.
A patch by me add support for SO_MARK to the AF_CAN protocol.
Geert Uytterhoeven's patch fixes the number of CAN channels in the
rcan_canfd bindings documentation.
In the last 11 patches Markus Schneider-Pargmann optimizes the
register access in the t_can driver and cleans up the tcan glue
driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Markus Schneider-Pargmann <msp@baylibre.com> says:
as requested I split the series into two parts. This is the first
parts with simple improvements to reduce the number of SPI transfers.
The second part will be the rest with coalescing support and more
complex optimizations.
Changes since v1: https://lore.kernel.org/all/20221116205308.2996556-1-msp@baylibre.com
- Fixed register ranges
- Added fixes: tag for two patches
Link: https://lore.kernel.org/all/20221206115728.1056014-1-msp@baylibre.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Specify exactly which registers are read/writeable in the chip. This
is supposed to help detect any violations in the future.
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Link: https://lore.kernel.org/all/20221206115728.1056014-12-msp@baylibre.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
According to the datasheet 0x10 is the last register in the first block,
not register 0x2c.
The datasheet lists the last register of the second block as 0x830, not
0x83c.
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Link: https://lore.kernel.org/all/20221206115728.1056014-11-msp@baylibre.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
TCAN4X5X_ERROR_STATUS is not a status register that needs clearing
during interrupt handling. Instead this is a masking register that masks
error interrupts. Writing TCAN4X5X_CLEAR_ALL_INT to this register
effectively masks everything.
Rename the register and mask all error interrupts only once by writing
to the register in tcan4x5x_init.
Fixes: 5443c226ba ("can: tcan4x5x: Add tcan4x5x driver to the kernel")
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Link: https://lore.kernel.org/all/20221206115728.1056014-10-msp@baylibre.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
