This adds the DT node for the mfd/ab8500-sysctrl driver. It will
allow probing of the driver during a Device Tree enabled boot.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch configures the user LED on Snowball to double flash
every second or so, whilst it's still alive. This can give key
indications as to what the board is doing in the case of no
console output.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch provides support for the ab8500-gpadc driver.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch enables and illuminates the user_led on the
Snowball low-cost development board using DT. It also
removes initialisation carried out from platform code.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Allow proper initialisation for MMC via the mmci driver
for the Snowball low-cost development board using DT. At
the moment we continue to use DMA setup from platform code.
Once the DMA generic DT bindings have been completed we
can then port the remainder over to DT.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add node for EXYNOS4 interrupt combiner controller.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
From Shawn Guo <shawn.guo@linaro.org>:
Here is the second (last) batch of mxs mxs device tree changes for 3.6.
* 'mxs/dt-for-3.6' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: dts: imx28-evk: add usb devices
ARM: mxs: rename dts files with soc name being the prefix
ARM: apx4devkit: add pin muxing for GPIOs
ARM: apx4devkit: remove AUART3
ARM: apx4devkit: add SSP2 support
ARM: apx4devkit: fix the bus-width of SSP0 to 4 bits
ARM: apx4devkit: add display support
ARM: apx4devkit: add NAND support
ARM: mxs: add dtb-y target into Makefile.boot
ARM: mxs: convert stmp378x_devb board to device tree
ARM: mxs: convert tx28 board to device tree
ARM: mxs: convert apx4devkit board to device tree
ARM: mxs: convert m28evk board to device tree
ARM: dts: imx28: move lcdif control pins into board dts
ARM: dts: imx28: move extra gpmi-nand pins into board dts
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
From Shawn Guo <shawn.guo@linaro.org>:
Here is the second (last) batch of imx device tree changes for 3.6.
* 'imx/dt-for-3.6' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: imx6q: ensure ANATOP controller is available
ARM: dts: imx6q-sabrelite: add ecspi1 pinctrl support
ARM: dts: imx6q-sabrelite: add usb devices
ARM: imx6q: disable usb charger detector
ARM: imx6q: add usbphy clocks
ARM: imx6q: add usb controller clock lookups
ARM: dts: imx: update #interrupt-cells for gpio nodes
bindings: update imx and mxs #gpio-cells
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
From Sascha Hauer <s.hauer@pengutronix.de>:
ARM i.MX dt updates for v3.6
* tag 'imx-dt' of git://git.pengutronix.de/git/imx/linux-2.6:
arm/dts: Add support for i.MX31 bug 1.x board from buglabs.
ARM i.MX31: Add devicetree support
ARM: dts: Add basic support for mx27_3ds board
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
From Tony Lindgren <tony@atomide.com>:
Device tree related patches for omaps
* tag 'omap-devel-dt-for-v3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
arm/dts: New dts file for PandaBoardES (4460)
arm/dts: omap4-panda: Audio support for PandaBoard 4430
arm/dts: omap4-sdp: Enable audio support via device tree
arm/dts: omap4-sdp: Add support for twl6040
arm/dts: omap4-sdp: Add fixed regulator to represent VBAT
arm/dts: omap4: Add entry for OMAP DMIC IP
arm/dts: omap4: Add entry for OMAP McPDM IP
arm/dts: am33xx wdt node
arm/dts: remove MMC/SD and SPI related entries from am33xx.dtsi
watchdog: omap_wdt: add device tree support
ARM: OMAP: avoid build wdt platform device if with dt support
arm/dts: add wdt node for omap3 and omap4
arm/dts: OMAP4: Add Variscite OMAP4 System-On-Modeule support
arm/dts: Add support for AM335x BeagleBone
arm/dts: Add support for AM335x EVM
arm/dts: Add initial DT support for AM33XX SoC family
arm/dts: omap3-evm: Add i2c and twl4030 support
arm/dts: Add support for TI AM3517/05 EVM board
arm/dts: OMAP2: Add support for OMAP2420H4 Board
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
From Nicolas Ferre <nicolas.ferre@atmel.com>:
Two new boards described with device tree
* tag 'at91-for-next-dt' of git://github.com/at91linux/linux-at91:
ARM: at91: Add support for board aks-cdu
ARM: at91: add support for Telit EVK-PRO3 with Telit GE863-PRO3
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This branch contains changes to Tegra device tree files, and related
Kconfig and Makefile changes. Highlights are:
* New support for the Whistler board.
* Use of the I2C pinctrl-based bus mux on Seaboard/Springbank.
This branch is based on Tegra's for-3.6/cleanup branch from a previous
pull request.
* 'for-3.6/dt' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
ARM: dt: tegra seaboard: move battery monitor to mux'd I2C bus.
ARM: dt: tegra: seaboard: instantiate pinctrl-based I2C bus mux
ARM: dt: tegra: add Whistler device tree file
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Imx6q sabrelite board uses ecspi1 to connect a spi flash sst25vf016b,
we need to add pinctrl information for it in the dts, otherwise the
ecspi1 driver can't work and the connected flash is wrongly
detected as a mr25h256 flash like this:
m25p80 spi32766.0: found mr25h256, expected sst25vf016b
m25p80 spi32766.0: mr25h256 (32 Kbytes)
Cc: Richard Zhao <richard.zhao@freescale.com>
Signed-off-by: Hui Wang <jason77.wang@gmail.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This adds real clock support to Calxeda Highbank SOC using the common
clock infrastructure.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
[mturquette@linaro.org: fixed up invalid writes to const struct member]
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Rename mxs dts files with soc name being the prefix, so that the board
dts file can be located easily by soc name, and we also gain the
consistency of naming.
Suggested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
AUART3 is not available anymore. Pins are used as GPIOs.
Signed-off-by: Lauri Hintsala <lauri.hintsala@bluegiga.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add HannStar display and device tree configuration.
Signed-off-by: Lauri Hintsala <lauri.hintsala@bluegiga.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The enc28j60 spi device does not get converted to dts file, because
there is no mxs spi driver on mainline so far. The enc28j60 spi
in mach-stmp378x_devb.c does not work anyway.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
FEC support is missing because we need to find a proper way to rewrite
tx28_add_fec0 for device tree boot.
Cc: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The presence and muxing of lcdif control pins can vary much on different
boards. Move them into imx28-evk.dts to make lcdif_24bit_pins_a only
about data pins, so that it can be reused by other boards.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Only pins GPMI_CE0N and GPMI_READY0 are generally used by other boards.
Move GPMI_CE1N and GPMI_READY1 into imx28-evk.dts to make gpmi_pins_a
more general, and can be used by other boards.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Only the main UART and the memory node information are added.
Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch adds basic devicetree support for i.MX31 based SoCs.
Only the UART and interrupts bindings are added.
Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
From Tony Lindgren <tony@atomide.com>:
This branch contains minimal support for omap5 to boot to a
console without clock framework support. This branch depends
on omap-cleanup-part2-for-v3.6.
* 'devel-omap5' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: Kconfig update to support additional GPIOs in OMAP5
ARM: OMAP5: Add the build support
arm/dts: OMAP5: Add omap5 dts files
ARM: OMAP5: board-generic: Add device tree support
ARM: omap2+: board-generic: clean up the irq data from board file
ARM: OMAP5: Add SMP support
ARM: OMAP5: Add the WakeupGen IP updates
ARM: OMAP5: l3: Add l3 error handler support for omap5
ARM: OMAP5: gpmc: Update gpmc_init()
ARM: OMAP5: timer: Add clocksource, clockevent support
ARM: OMAP5: Add minimal support for OMAP5430 SOC
ARM: OMAP5: id: Add cpu id for ES versions
ARM: OMAP: counter-32k: Select the CR register offset using the IP scheme
ARM: OMAP2+: Move stubbed secure_sram_reserve function to a common.c and call it __weak
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[ben.dooks@codethink.co.uk: ensure error check on of_property_read_u32]
[ben.dooks@codethink.co.uk: use mpic address instead of bus-unit's ]
[ben.dooks@codethink.co.uk: BUG_ON() if the of_iomap() fails for mpic]
[ben.dooks@codethink.co.uk: move mpic per-cpu register base ]
[ben.dooks@codethink.co.uk: number fetch should use irqd_to_hwirq()]
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Lior Amsalem <alior@marvell.com>
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Yehuda Yitschak <yehuday@marvell.com>
Tested-by: Lior Amsalem <alior@marvell.com>
Add support for our "aks-cdu" board based up on Telit's module GE863 Pro3.
It has more uarts, leds, another nand partitioning.
Signed-off-by: Jiri Prchal <jiri.prchal@aksignal.cz>
[nicolas.ferre@atmel.com: correction of the dts file]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This patch allows the ATAG_CMDLINE provided by the bootloader to be
concatenated to the bootargs property of the device tree.
This is useful to merge static values defined in the device tree
with the boot loader's (possibly) more dynamic values, such as
startup reasons and more.
The bootloader should use the device tree to pass those values to
the kernel, but that's not always simple (old bootloader or very
small one).
The behaviour is the same as the one introduced by Victor Boivie in
4394c12442 by extending the CONFIG_CMDLINE.
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Adding the minimum device tree files required for
OMAP5 to boot.
Reviewed-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
The 4430 and 4460 version of PandaBoard mostly the same with
exception at least in audio setup.
Use the omap4-panda.dts file as a base and only override the differences
between the revisions.
For audio it is the name of the sound card and the routing information.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
PandaBoard uses twl6040 connected via McPDM for audio.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On OMAP4 SDP the audio setup includes the twl6040 codec and digital
microphones.
Since OMAP4 SDP is a reference board it has all possible audio interfaces
connected. This information is passed via the ti,audio-routing
property.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The twl6040 provides the audio and vibra support on OMAP4 SDP boards.
It is connected to i2c1 bus with 0x4b address.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
DMIC IP is used to connect up to 6 digital microphones directly to OMAP.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
McPDM is used on OMAP4 based boards to communicate with an external audio
codec (twl6040).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The MMC/SD and SPI entries in this file are not tested yet. They
inadvertently came into the patch because of some work in progress
stuff I had in my repo.
These entries should not have been sent out in the first place and
I am sorry for the trouble and will be extra careful in future.
Since the offending commit is not sent upstream yet, I hope this can
be merged into the commit 5fc0b42a98
(arm/dts: Add initial DT support for AM33XX SoC family) on the devel-dt
branch of linux-omap tree.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add a very basic dt support for mx27_3ds (also known as mx27pdk).
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Change the value of #interrupt-cells of gpio nodes from 1 to 2, so that
the gpio irq type can be specified in device tree. Also update binding
document to make it clear.
Reported-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add generic DT board support for the sh7377 SoC.
SCIF serial ports and timers are kept as regular
platform devices. Other on-chip and on-board devices
should be configured via the device tree.
At this point there is no interrupt controller support
in place but such code will be added over time when
proper IRQ domain support has been added to INTC.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Add generic DT board support for the r8a7740 SoC.
SCIF serial ports and timers are kept as regular
platform devices. Other on-chip and on-board devices
should be configured via the device tree.
At this point there is no interrupt controller support
in place but such code will be added over time when
proper IRQ domain support has been added to INTC.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Tegra's I2C2 controller can be routed to either the PTA or DDC pin group
on Seaboard. Define the pinctrl state nodes required to allow runtime
control of this routing. Instantiate a pinctrl-i2cmux I2C bus mux that
uses these pinctrl states.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Whistler is a highly configurable Tegra evaluation and development board.
This change adds support for the following specific configuration:
E1120 motherboard
E1108 CPU board
E1116 PMU board
The motherboard configuration switches are set as follows:
SW1=0 SW2=0 SW3=5
S1/S2/S3/S4 all on, except S3 7/8 are off.
Other combinations of daugher boards may work to varying degrees, but will
likely require some SW adjustment.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
mx23-olinuxino is a low cost board designed by Olimex.
It has the following features:
- Freescale iMX233 ARM926J processor at 454MHz
-64 MB RAM
-SD-card connector
-TV PAL/NTSC video output
-2 USB High Speed Hosts
-Ethernet 100 Mbit
-Stereo Audio Input
-Stereo Headphones Audio Output
More information at:
http://www.olimex.com/dev/imx233-olinuxino-maxi.html
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Device's regulator matches their hardware counterparts with the
property "regulator-compatible" of each child regulator node in
place of the child node name.
Add the property "regulator-compatible" for each regulator with
their hardware counterpart's name.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add Variscite OMAP4 System-On-Modeule support
Signed-off-by: Uri Yosef <uri.y@variscite.com>
[tony@atomide.com: updated to use disabled instead of disable]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add AM335X BeagleBone device tree source (am335x-evm.dts) file
to use the am33xx.dtsi SoC file, along with the memory node
information.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Reviewed-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add AM335X EVM device tree source (am335x-evm.dts) file to
use the am33xx.dtsi SoC file, along with the memory node
information.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Reviewed-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add device tree source include file for the AM33XX SoC family.
An additional .dtsi file is created to describe the generic
AM33XX CPU module like intc, ocp.
Actual selection of available peripherals is handled in seperate
.dts files using this am33xx.dtsi generic header file.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Reviewed-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add missing properties for fec, phy-supply, phy-reset-gpios and
phy-reset-duration, which are required by fec driver for successfully
probe fec from device tree, if bootloader hasn't set those things up.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add vmmc-supply for mmc device, so that the power to mmc slot can be
turned on by mmc driver if bootloader hasn't done it.
Also remove "okay" status for mmc1/ssp1, as the device has pin conflict
with gpmi-nand. Actually the device is already disabled since the
mxs-mmc driver adopts pinctrl support because there is no pinctrl setup
for the device in dts. Make this explicit by removing "okay" status.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The 8-bit mode mmc has pin conflicts with display. Let's use 4-bit
mode by default, so that display can be enabled together later.
Also add vmmc-supply for mmc device.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Before gpio_request can directly ask pinctrl system to configure the
requested pin into gpio mode, we use "hog" entry (pinctrl state of
pin controller itself) to configure gpios.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add comments for pinmux-ids so that we do not have to keep looking at
Documentation/devicetree/bindings/pinctrl/fsl,mxs-pinctrl.txt to read
all these pinmux-ids.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Replace "gpmi" with "gpmi-nand" to get the
GPMI interface probing with DT instead of
failing to get clock.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
CC: Dong Aisheng <b29396@freescale.com>
CC: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Linux ARM kernel <linux-arm-kernel@lists.infradead.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
add gpmi-nand device tree support.
add gpmi-nand pinctrl support.
Also enable the gpmi support for mx28-evk board.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add auxdata to instantiate the PWFM controller from a device tree,
include the corresponding nodes in the dtsi files for Tegra 20 and
Tegra 30 and add binding documentation.
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Add a third cell to define irq priority.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Reviewed-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Add support for TWL4030, which is interfaced on i2c1 bus.
Also add clock frequencies for other i2c instances (2 & 3)
required for client-device exist on OMAP3EVM board.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add AM3517 EVM (AM3517/05) DTS file to use the omap3.dtsi SoC file,
along with memory node and basic i2c information.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Simple DTS file for OMAP2420H4 board adding memory information to allow
device-tree testing on an OMAP2420. OMAP2420H4 board has 64MB of RAM.
Verified that kernel boots with DT using a simple RAMDISK file-system on
OMAP2420H4.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add the DT node for gpmi nand.
Add the pinmux support for gpmi nand.
The gpmi nand may conflicts with other modules, such as MMC.
So we do not enable the gpmi nand for mx6q-arm2 board, just add the
node for the board.
Acked-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The powerdomain and clockdomain data for the AM35xx are finally fixed.
The AM35xx EMAC/MDIO Ethernet controller integration code has been
converted to use the OMAP device and hwmod framework. Also the UART4
and HSOTGUSB warnings have been fixed.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJP7BHOAAoJEMePsQ0LvSpLCrcP/RwJliq2ITgQMEj3N2BbDkKP
kvS63qYv+QqH+mhGm/RFrmB/p3LSxgOkgdQByavfsQnsE0v5+FYjDnXAB3tvUVHI
Tv9vSJLIAgC9n4Z8pdJ8u71VGu8XVYnGnCKNz6UhVfHX8Q5BEs01eSPw3wgDVTIq
gKpMHaeNdi4Atkh2KmxyLwEBF9QC+vSNxMtkqcYbT5faBrqOEKeLz5igG8+VQBTU
RNeUOHb99+Rf/H2eRsynwMgX63xMzh7hSwW2GAJ5O7+uoMLmdPuI7MUAQR/zcPzQ
gmFUb1yKkmvu9OKtNR+3VCgGGlvvhaJBwTFJj9IL10xrj4LnDlA3N9bC9vwHG8zw
0YbrPA2iLU6ufdmLf5rANQFJL3ttg65MZTsjA8q3tjE04QkJncRpDtzr89dQYw/C
hv3vqCYpo0b2UCMPcyf4pUR5rzzHjPiM4Np9GEj3Ak1puUASwNXGTvXWusWXND9i
ixcFxd6LppyIa8FxMKXONEGaeNKbp+T63EugBCDEeCCWkXXQQGXU54xWy7w939ib
pvDtk1+ZqHC5rzPfuNokD+H95W3pc5AYr2pPjW8fctH6Wp9dFZV8sg77pgbenS/E
u2UX5N7rlqtj/Km7fJgy6h3EUVg8ky6W5nMtF2Jad8D89FOZHoSRAICPA4dIxTYl
hvv7kdtT23AqZKbxQUNu
=2b0z
-----END PGP SIGNATURE-----
Merge tag 'omap-devel-d-for-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into fixes-non-critical
Some OMAP AM35xx fixes.
The powerdomain and clockdomain data for the AM35xx are finally fixed.
The AM35xx EMAC/MDIO Ethernet controller integration code has been
converted to use the OMAP device and hwmod framework. Also the UART4
and HSOTGUSB warnings have been fixed.
Add support for L2 ECC on Calxeda highbank platform.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for memory controller on Calxeda Highbank platforms. Highbank
platforms support a single 4GB mini-DIMM with 1-bit correction and 2-bit
detection.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Nothing very controversial in here. Most of the fixes are for OMAP this time
around, with some orion/kirkwood and a tegra patch mixed in.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=6Ahb
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Nothing very controversial in here. Most of the fixes are for OMAP
this time around, with some orion/kirkwood and a tegra patch mixed in."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: Orion: Fix Virtual/Physical mixup with watchdog
ARM: Kirkwood: clk_register_gate_fn: add fn assignment
ARM: Orion5x - Restore parts of io.h, with rework
ARM: OMAP4: hwmod data: Force HDMI in no-idle while enabled
ARM: OMAP2+: mux: fix sparse warning
ARM: OMAP2+: CM: increase the module disable timeout
ARM: OMAP4: clock data: add clockdomains for clocks used as main clocks
ARM: OMAP4: hwmod data: fix 32k sync timer idle modes
ARM: OMAP4+: hwmod: fix issue causing IPs not going back to Smart-Standby
ARM: OMAP: Fix Beagleboard DVI reset gpio
arm/dts: OMAP2: Fix interrupt controller binding
ARM: OMAP2: Fix tusb6010 GPIO interrupt for n8x0
ARM: OMAP2+: Fix MUSB ifdefs for platform init code
ARM: tegra: make tegra_cpu_reset_handler_enable() __init
ARM: OMAP: PM: Lock clocks list while generating summary
ARM: iconnect: Remove include of removed linux/spi/orion_spi.h
reset. All of them are regression fixes, except for the missing omap2
interrupt controller binding that somehow got missed earlier.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=cMPJ
-----END PGP SIGNATURE-----
Merge tag 'omap-fixes-for-v3.5-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
From Tony Lindgren:
"Here are a few fixes with the biggest one being fix for Beagle DVI
reset. All of them are regression fixes, except for the missing omap2
interrupt controller binding that somehow got missed earlier."
* tag 'omap-fixes-for-v3.5-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP: Fix Beagleboard DVI reset gpio
arm/dts: OMAP2: Fix interrupt controller binding
ARM: OMAP2: Fix tusb6010 GPIO interrupt for n8x0
ARM: OMAP2+: Fix MUSB ifdefs for platform init code
This patches fixes some status = "disable" strings to "disabled", the correct
way of disabling nodes in the devicetree.
Just the OMAP part here, the rest goes via other patches and trees.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
* emailed from Andrew Morton <akpm@linux-foundation.org>: (21 patches)
mm/memblock: fix overlapping allocation when doubling reserved array
c/r: prctl: Move PR_GET_TID_ADDRESS to a proper place
pidns: find_new_reaper() can no longer switch to init_pid_ns.child_reaper
pidns: guarantee that the pidns init will be the last pidns process reaped
fault-inject: avoid call to random32() if fault injection is disabled
Viresh has moved
get_maintainer: Fix --help warning
mm/memory.c: fix kernel-doc warnings
mm: fix kernel-doc warnings
mm: correctly synchronize rss-counters at exit/exec
mm, thp: print useful information when mmap_sem is unlocked in zap_pmd_range
h8300: use the declarations provided by <asm/sections.h>
h8300: fix use of extinct _sbss and _ebss
xtensa: use the declarations provided by <asm/sections.h>
xtensa: use "test -e" instead of bashism "test -a"
xtensa: replace xtensa-specific _f{data,text} by _s{data,text}
memcg: fix use_hierarchy css_is_ancestor oops regression
mm, oom: fix and cleanup oom score calculations
nilfs2: ensure proper cache clearing for gc-inodes
thp: avoid atomic64_read in pmd_read_atomic for 32bit PAE
...
viresh.kumar@st.com email-id doesn't exist anymore as I have left the
company. Replace ST's id with viresh.linux@gmail.com.
It also updates .mailmap file to fix address for 'git shortlog'
Signed-off-by: Viresh Kumar <viresh.linux@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patches fixes some status = "disable" strings to "disabled", the correct
way of disabling nodes in the devicetree.
Just the tegra part here. Everything else goes via other patches and trees.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Most ARM ${board}.dts files are already named ${soc}-${board}.dts. This
change modifies the Tegra board files to be named the same way for
consistency.
Once a related change is made in U-Boot, this will cause both U-Boot and
the kernel to use the same names for the .dts files and SoC identifiers,
thus allowing U-Boot's recently added "soc" and "board" environment
variables to be used to construct the name of Tegra .dtb files, and hence
allow board-generic U-Boot bootcmd scripts to be written.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
When booting with device-tree on an OMAP2420H4, the kernel is hanging when
initialising the interrupts and following kernel dumps is seen ...
[ 0.000000] ------------[ cut here ]------------
[ 0.000000] WARNING: at arch/arm/mach-omap2/irq.c:271 omap_intc_of_init+0x50/0xb4()
[ 0.000000] unable to get intc registers
[ 0.000000] Modules linked in:
[ 0.000000] [<c001befc>] (unwind_backtrace+0x0/0xf4) from [<c0040c34>] (warn_slowpath_common+0x4c/0x64)
[ 0.000000] [<c0040c34>] (warn_slowpath_common+0x4c/0x64) from [<c0040ce0>] (warn_slowpath_fmt+0x30/0x40)
[ 0.000000] [<c0040ce0>] (warn_slowpath_fmt+0x30/0x40) from [<c066b8a4>] (omap_intc_of_init+0x50/0xb4)
[ 0.000000] [<c066b8a4>] (omap_intc_of_init+0x50/0xb4) from [<c0688b70>] (of_irq_init+0x144/0x288)
[ 0.000000] [<c0688b70>] (of_irq_init+0x144/0x288) from [<c0663294>] (init_IRQ+0x14/0x1c)
[ 0.000000] [<c0663294>] (init_IRQ+0x14/0x1c) from [<c06607fc>] (start_kernel+0x198/0x304)
[ 0.000000] [<c06607fc>] (start_kernel+0x198/0x304) from [<80008044>] (0x80008044)
[ 0.000000] ---[ end trace 1b75b31a2719ed1c ]---
[ 0.000000] of_irq_init: children remain, but no parents
The OMAP2 interrupt controller binding is missing the number of interrupts and
interrupt controller register address. Adding these fixes the problem.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add the reg, cs-gpios and max-frequencies that are needed for spi
device registry in phy3250.
Adds also the pl022 internal transfers details via dt
Signed-off-by: Alexandre Pereira da Silva <aletes.xgr@gmail.com>
Signed-off-by: Roland Stigge <stigge@antcom.de>
This patches fixes some status = "disable" strings to "disabled", the correct
way of disabling nodes in the devicetree.
Signed-off-by: Roland Stigge <stigge@antcom.de>
This patch fixes the DTS files for the High Speed UARTs 1, 2 and 7 of the
LPC32xx SoC, adjusting the compatible strings, adding interrupts and status
configuration. On the PHY3250 reference board, UART2 is enabled.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Acked-by: Alexandre Pereira da Silva <aletes.xgr@gmail.com>
This patch switches from static serial driver initialization to devicetree
configuration. This way, the Standard UARTs of the LPC32xx SoC can be enabled
individually via DT.
E.g., instead of Kconfig configuration, the phy3250.dts activates
UARTs 3 and 5.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Tested-by: Alexandre Pereira da Silva <aletes.xgr@gmail.com>
This patch connects the lpc32xx-key driver to the LPC32xx platform (via
lpc32xx.dtsi), and more specifically to the reference board via its dts file.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Alexandre Pereira da Silva <aletes.xgr@gmail.com>
There is another reference/development board for the LPC32xx SoC (besides the
Phytec 3250): The Embedded Artists LPC3250 board. This patch adds a default dts
file for it.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Acked-by: Alexandre Pereira da Silva <aletes.xgr@gmail.com>
This patch takes into account that the MTD NAND MLC controller needs more
registers, located actually before the previously allocated memory range,
already starting at 200a8000 instead of 200b0000.
Further, the interrupt for the controller is configured.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Tested-by: Alexandre Pereira da Silva <aletes.xgr@gmail.com>
This patch adds necessary NAND flash timings to the board specific dts file of
the PHY3250 reference board of the LPC32xx SoC.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Tested-by: Alexandre Pereira da Silva <aletes.xgr@gmail.com>
Use a more plain english name.
Signed-off-by: Hiroshi DOYU <hdoyu@nvidia.com>
[swarren: also rename the node in tegra-seaboard.dts]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Use a more plain english name.
Signed-off-by: Hiroshi DOYU <hdoyu@nvidia.com>
[swarren: remove redundant unit address from tegra30.dtsi change]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
- Updates to mxc_nand and gpmi drivers to support new boards and device tree
- Improve consistency of information about ECC strength in NAND devices
- Clean up partition handling of plat_nand
- Support NAND drivers without dedicated access to OOB area
- BCH hardware ECC support for OMAP
- Other fixes and cleanups, and a few new device IDs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iEYEABECAAYFAk/JG1wACgkQdwG7hYl686M80wCglN4kutx20j+KJWuZofkr9Hog
weEAoI4jrqEWEdW9EcT2CIWQw7eG+1v+
=7tdo
-----END PGP SIGNATURE-----
Merge tag 'for-linus-3.5-20120601' of git://git.infradead.org/linux-mtd
Pull mtd update from David Woodhouse:
- More robust parsing especially of xattr data in JFFS2
- Updates to mxc_nand and gpmi drivers to support new boards and device tree
- Improve consistency of information about ECC strength in NAND devices
- Clean up partition handling of plat_nand
- Support NAND drivers without dedicated access to OOB area
- BCH hardware ECC support for OMAP
- Other fixes and cleanups, and a few new device IDs
Fixed trivial conflict in drivers/mtd/nand/gpmi-nand/gpmi-nand.c due to
added include files next to each other.
* tag 'for-linus-3.5-20120601' of git://git.infradead.org/linux-mtd: (75 commits)
mtd: mxc_nand: move ecc strengh setup before nand_scan_tail
mtd: block2mtd: fix recursive call of mtd_writev
mtd: gpmi-nand: define ecc.strength
mtd: of_parts: fix breakage in Kconfig
mtd: nand: fix scan_read_raw_oob
mtd: docg3 fix in-middle of blocks reads
mtd: cfi_cmdset_0002: Slight cleanup of fixup messages
mtd: add fixup for S29NS512P NOR flash.
jffs2: allow to complete xattr integrity check on first GC scan
jffs2: allow to discriminate between recoverable and non-recoverable errors
mtd: nand: omap: add support for hardware BCH ecc
ARM: OMAP3: gpmc: add BCH ecc api and modes
mtd: nand: check the return code of 'read_oob/read_oob_raw'
mtd: nand: remove 'sndcmd' parameter of 'read_oob/read_oob_raw'
mtd: m25p80: Add support for Winbond W25Q80BW
jffs2: get rid of jffs2_sync_super
jffs2: remove unnecessary GC pass on sync
jffs2: remove unnecessary GC pass on umount
jffs2: remove lock_super
mtd: gpmi: add gpmi support for mx6q
...
The Nomadik GPIO controller now relies on Nomadik pinctrl, however
the pinctrl driver is not currently started by any ux500 platform.
This is requred or GPIOs do not work at all.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Here we supply the information required to setup regulators successfully
on Snowball and other db8500 variants which use the ab8500 regulators.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patch adds a fixed regulator for use by the SMSC911x Ethernet
chip driver into the db8500 Device Tree. It also references other
regulators required by the same device.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Here we inform Device Tree of which regulators are provided by the db8500-
prcmu. This way we can reference some of their consumers directly from the
Device Tree e.g. SMSC911x Ethernet chip.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patch applies the correct format requested by the irq
domain. For chained IRQs which use GPIO lines as IRQs, we
stipulate that a two cell request is required. The first cell
contains the requested IRQ and the second can contain flags
pertaining to edge detection and level sensitive values. The
zeroth cell specifies the GPIO controller by use of a phandle.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Apply db8500 related PRCMU Device Tree settings and clean up some formatting
errors. We also remove one of the PRCMU assigned IRQs, as it is currently not
used.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The GPIO devicetree binding in 3.5 doesn't register the various LPC32xx GPIO
banks via DT subnodes but always all at once, and changes the gpio referencing
to 3 cells (bank, gpio, flags). This patch adjusts the DTS files to this
binding that was just accepted to the gpio subsystem.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
* late/soc:
ARM: vexpress: Remove twice included header files
ARM: vexpress: Device Tree updates
ARM: EXYNOS: Support suspend and resume for EXYNOS5250
ARM: EXYNOS: Add Clock register list for save and restore
ARM: EXYNOS: Add PMU table for EXYNOS5250
ARM: EXYNOS: Rename of function for pm.c
ARM: EXYNOS: Remove GIC save & restore function
ARM: dts: Add node for interrupt combiner controller on EXYNOS5250
ARM: S3C24XX: add support for second irq set of S3C2416
A few device tree updates and an include file fix for versatile.
* 'vexpress-v3.4' of git://git.linaro.org/people/pawelmoll/linux:
ARM: vexpress: Remove twice included header files
ARM: vexpress: Device Tree updates
+ update to 3.4
Signed-off-by: Olof Johansson <olof@lixom.net>
This adds support for the spear13xx platform, which has first been under
review a long time ago and finally been completed after generic spear
work has gone into the clock, dt and pinctrl branches.
Also a number of updates for the samsung socs are part of this branch.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=W2Ri
-----END PGP SIGNATURE-----
Merge tag 'soc2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc: soc specific changes (part 2) from Olof Johansson:
"This adds support for the spear13xx platform, which has first been
under review a long time ago and finally been completed after generic
spear work has gone into the clock, dt and pinctrl branches.
Also a number of updates for the samsung socs are part of this branch."
Fix up trivial conflicts in drivers/gpio/gpio-samsung.c that look much
worse than they are: the exonys5 init code was refactored in commit
fd454997d6 ("gpio: samsung: refactor gpiolib init for exynos4/5"), and
then commit f10590c983 ("ARM: EXYNOS: add GPC4 bank instance") added a
new gpio chip define and did tiny updates to the init code.
So the conflict diff looks like hell, but it's actually a fairly simple
change.
* tag 'soc2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (34 commits)
ARM: exynos: fix building with CONFIG_OF disabled
ARM: EXYNOS: Add AUXDATA for i2c controllers
ARM: dts: Update device tree source files for EXYNOS5250
ARM: EXYNOS: Add device tree support for interrupt combiner
ARM: EXYNOS: Add irq_domain support for interrupt combiner
ARM: EXYNOS: Remove a new bus_type instance for EXYNOS5
ARM: EXYNOS: update irqs for EXYNOS5250 SoC
ARM: EXYNOS: Add pre-divider and fout mux clocks for bpll and mpll
ARM: EXYNOS: add GPC4 bank instance
ARM: EXYNOS: Redefine IRQ_MCT_L0,1 definition
ARM: EXYNOS: Modify the GIC physical address for static io-mapping
ARM: EXYNOS: Add watchdog timer clock instance
pinctrl: SPEAr1310: Fix pin numbers for clcd_high_res
SPEAr: Update MAINTAINERS and Documentation
SPEAr13xx: Add defconfig
SPEAr13xx: Add compilation support
SPEAr13xx: Add dts and dtsi files
pinctrl: Add SPEAr13xx pinctrl drivers
pinctrl: SPEAr: Create macro for declaring GPIO PINS
SPEAr13xx: Add common clock framework support
...
These continue the device tree work from part 1, this set is for the
tegra, mxs and imx platforms, all of which have dependencies on clock
or pinctrl changes submitted earlier.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=WeDQ
-----END PGP SIGNATURE-----
Merge tag 'dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc device tree conversions (part 2) from Olof Johansson:
"These continue the device tree work from part 1, this set is for the
tegra, mxs and imx platforms, all of which have dependencies on clock
or pinctrl changes submitted earlier."
Fix up trivial conflicts due to nearby changes in
drivers/{gpio/gpio,i2c/busses/i2c}-mxs.c
* tag 'dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (73 commits)
ARM: dt: tegra: invert status=disable vs status=okay
ARM: dt: tegra: consistent basic property ordering
ARM: dt: tegra: sort nodes based on bus order
ARM: dt: tegra: remove duplicate device_type property
ARM: dt: tegra: consistenly use lower-case for hex constants
ARM: dt: tegra: format regs properties consistently
ARM: dt: tegra: gpio comment cleanup
ARM: dt: tegra: remove unnecessary unit addresses
ARM: dt: tegra: whitespace cleanup
ARM: dt: tegra cardhu: fix typo in SDHCI node name
ARM: dt: tegra: cardhu: register core regulator tps62361
ARM: dt: tegra30.dtsi: Add SMMU node
ARM: dt: tegra20.dtsi: Add GART node
ARM: dt: tegra30.dtsi: Add Memory Controller(MC) nodes
ARM: dt: tegra20.dtsi: Add Memory Controller(MC) nodes
ARM: dt: tegra: Add device tree support for AHB
ARM: dts: enable audio support for imx28-evk
ARM: dts: enable i2c device for imx28-evk
i2c: mxs: add device tree probe support
ARM: dts: enable mmc for imx28-evk
...
The new clock subsystem was merged in linux-3.4 without any users, this
now moves the first three platforms over to it: imx, mxs and spear.
The series also contains the changes for the clock subsystem itself,
since Mike preferred to have it together with the platforms that require
these changes, in order to avoid interdependencies and conflicts.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=rwFF
-----END PGP SIGNATURE-----
Merge tag 'clock' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc clock driver changes from Olof Johansson:
"The new clock subsystem was merged in linux-3.4 without any users,
this now moves the first three platforms over to it: imx, mxs and
spear.
The series also contains the changes for the clock subsystem itself,
since Mike preferred to have it together with the platforms that
require these changes, in order to avoid interdependencies and
conflicts."
Fix up trivial conflicts in arch/arm/mach-kirkwood/common.c (code
removed in one branch, added OF support in another) and
drivers/dma/imx-sdma.c (independent changes next to each other).
* tag 'clock' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (97 commits)
clk: Fix CLK_SET_RATE_GATE flag validation in clk_set_rate().
clk: Provide dummy clk_unregister()
SPEAr: Update defconfigs
SPEAr: Add SMI NOR partition info in dts files
SPEAr: Switch to common clock framework
SPEAr: Call clk_prepare() before calling clk_enable
SPEAr: clk: Add General Purpose Timer Synthesizer clock
SPEAr: clk: Add Fractional Synthesizer clock
SPEAr: clk: Add Auxiliary Synthesizer clock
SPEAr: clk: Add VCO-PLL Synthesizer clock
SPEAr: Add DT bindings for SPEAr's timer
ARM i.MX: remove now unused clock files
ARM: i.MX6: implement clocks using common clock framework
ARM i.MX35: implement clocks using common clock framework
ARM i.MX5: implement clocks using common clock framework
ARM: Kirkwood: Replace clock gating
ARM: Orion: Audio: Add clk/clkdev support
ARM: Orion: PCIE: Add support for clk
ARM: Orion: XOR: Add support for clk
ARM: Orion: CESA: Add support for clk
...
These changes are specific to some driver that may be used by multiple
boards or socs. The most significant change in here is the move of the
samsung iommu code from a platform specific in-kernel interface to the
generic iommu subsystem.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=hgkg
-----END PGP SIGNATURE-----
Merge tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc driver specific updates from Olof Johansson:
"These changes are specific to some driver that may be used by multiple
boards or socs. The most significant change in here is the move of
the samsung iommu code from a platform specific in-kernel interface to
the generic iommu subsystem."
Fix up trivial conflicts in arch/arm/mach-exynos/Kconfig
* tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (28 commits)
mmc: dt: Consolidate DT bindings
iommu/exynos: Add iommu driver for EXYNOS Platforms
ARM: davinci: optimize the DMA ISR
ARM: davinci: implement DEBUG_LL port choice
ARM: tegra: Add SMMU enabler in AHB
ARM: tegra: Add Tegra AHB driver
Input: pxa27x_keypad add choice to set direct_key_mask
Input: pxa27x_keypad direct key may be low active
Input: pxa27x_keypad bug fix for direct_key_mask
Input: pxa27x_keypad keep clock on as wakeup source
ARM: dt: tegra: pinmux changes for USB ULPI
ARM: tegra: add USB ULPI PHY reset GPIO to device tree
ARM: tegra: don't hard-code USB ULPI PHY reset_gpio
ARM: tegra: change pll_p_out4's rate to 24MHz
ARM: tegra: fix pclk rate
ARM: tegra: reparent sclk to pll_c_out1
ARM: tegra: Add pllc clock init table
ARM: dt: tegra cardhu: basic audio support
ARM: dt: tegra30.dtsi: Add audio-related nodes
ARM: tegra: add AUXDATA required for audio
...
Here is the big staging tree pull request for the 3.5-rc1 merge window.
Loads of changes here, and we just narrowly added more lines than we
added:
622 files changed, 28356 insertions(+), 26059 deletions(-)
But, good news is that there is a number of subsystems that moved out of
the staging tree, to their respective "real" portions of the kernel.
Code that moved out was:
- iio core code
- mei driver
- vme core and bridge drivers
There was one broken network driver that moved into staging as a step
before it is removed from the tree (pc300), and there was a few new
drivers added to the tree:
- new iio drivers
- gdm72xx wimax USB driver
- ipack subsystem and 2 drivers
All of the movements around have acks from the various subsystem
maintainers, and all of this has been in the linux-next tree for a
while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk+7q8MACgkQMUfUDdst+ymjogCguo8fANFVlPWeZGeoBTL+aQfQ
yTkAoLE0codmh+2SvhulYgyU1Wh6ZDK2
=nJ2F
-----END PGP SIGNATURE-----
Merge tag 'staging-3.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging tree changes from Greg Kroah-Hartman:
"Here is the big staging tree pull request for the 3.5-rc1 merge
window.
Loads of changes here, and we just narrowly added more lines than we
added:
622 files changed, 28356 insertions(+), 26059 deletions(-)
But, good news is that there is a number of subsystems that moved out
of the staging tree, to their respective "real" portions of the
kernel.
Code that moved out was:
- iio core code
- mei driver
- vme core and bridge drivers
There was one broken network driver that moved into staging as a step
before it is removed from the tree (pc300), and there was a few new
drivers added to the tree:
- new iio drivers
- gdm72xx wimax USB driver
- ipack subsystem and 2 drivers
All of the movements around have acks from the various subsystem
maintainers, and all of this has been in the linux-next tree for a
while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
Fixed up various trivial conflicts, along with a non-trivial one found
in -next and pointed out by Olof Johanssen: a clean - but incorrect -
merge of the arch/arm/boot/dts/at91sam9g20.dtsi file. Fix up manually
as per Stephen Rothwell.
* tag 'staging-3.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (536 commits)
Staging: bcm: Remove two unused variables from Adapter.h
Staging: bcm: Removes the volatile type definition from Adapter.h
Staging: bcm: Rename all "INT" to "int" in Adapter.h
Staging: bcm: Fix warning: __packed vs. __attribute__((packed)) in Adapter.h
Staging: bcm: Correctly format all comments in Adapter.h
Staging: bcm: Fix all whitespace issues in Adapter.h
Staging: bcm: Properly format braces in Adapter.h
Staging: ipack/bridges/tpci200: remove unneeded casts
Staging: ipack/bridges/tpci200: remove TPCI200_SHORTNAME constant
Staging: ipack: remove board_name and bus_name fields from struct ipack_device
Staging: ipack: improve the register of a bus and a device in the bus.
staging: comedi: cleanup all the comedi_driver 'detach' functions
staging: comedi: remove all 'default N' in Kconfig
staging: line6/config.h: Delete unused header
staging: gdm72xx depends on NET
staging: gdm72xx: Set up parent link in sysfs for gdm72xx devices
staging: drm/omap: initial dmabuf/prime import support
staging: drm/omap: dmabuf/prime mmap support
pstore/ram: Add ECC support
pstore/ram: Switch to persistent_ram routines
...
While we generally attempt to get rid of board specific files and replace
them with device tree based descriptions, a lot of platforms have not
come that far:
In shmobile, we add two new board files because their recently started
effort to add DT support has not proceeded enough to use it for all of
the important hardware.
In Kirkwood, we are adding support for new boards with a combination of
DT and board file contents in multiple cases.
pxa/mmp and imx are extending support for existing board files but not
adding new ones.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=wkmj
-----END PGP SIGNATURE-----
Merge tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc board specific changes from Olof Johansson:
"While we generally attempt to get rid of board specific files and
replace them with device tree based descriptions, a lot of platforms
have not come that far:
In shmobile, we add two new board files because their recently started
effort to add DT support has not proceeded enough to use it for all of
the important hardware.
In Kirkwood, we are adding support for new boards with a combination
of DT and board file contents in multiple cases.
pxa/mmp and imx are extending support for existing board files but not
adding new ones."
Fix up trivial conflicts in arch/arm/mach-{mmp/ttc_dkb.c,shmobile/{Kconfig,Makefile}}
* tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (94 commits)
ARM: shmobile: fix smp build
ARM: kirkwood: Add support for RaidSonic IB-NAS6210/6220 using devicetree
kirkwood: Add iconnect support
orion/kirkwood: create a generic function for gpio led blinking
kirkwood/orion: fix orion_gpio_set_blink
ARM: kirkwood: Define DNS-320/DNS-325 NAND in fdt
kirkwood: Allow nand to be configured via. devicetree
mtd: Add orion_nand devicetree bindings
ARM: kirkwood: Basic support for DNS-320 and DNS-325
ARM: mach-shmobile: Use DT_MACHINE for armadillo 800 eva
ARM: mach-shmobile: Use DT_MACHINE for KZM9G
ARM: pxa: hx4700: Add Synaptics NavPoint touchpad
ARM: pxa: Use REGULATOR_SUPPLY macro
ARM: mach-shmobile: kzm9g: enable SMP boot
ARM: mach-shmobile: kzm9g: defconfig update
ARM: mach-shmobile: kzm9g: add PCF8757 gpio-key
ARM: mach-shmobile: kzm9g: add SDHI support
ARM: mach-shmobile: kzm9g: add MMCIF support
ARM: mach-shmobile: kzm9g: correct screen direction
ARM: mach-shmobile: sh73a0.h: add GPIO_NR
...
With this, five platforms are moving to the relatively new pinctrl
subsystem for their pin management, replacing the older soc specific
in-kernel interfaces with common code.
There is quite a bit of net addition of code for each platform being
added to the pinctrl subsystem. but the payback comes later when adding
new boards can be done by only providing new device trees instead.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=HIfz
-----END PGP SIGNATURE-----
Merge tag 'pinctrl' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm soc-specific pinctrl changes from Olof Johansson:
"With this, five platforms are moving to the relatively new pinctrl
subsystem for their pin management, replacing the older soc specific
in-kernel interfaces with common code.
There is quite a bit of net addition of code for each platform being
added to the pinctrl subsystem. But the payback comes later when
adding new boards can be done by only providing new device trees
instead."
Fix up trivial conflicts in arch/arm/mach-ux500/{Makefile,board-mop500.c}
* tag 'pinctrl' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (61 commits)
mtd: nand: gpmi: fix compile error caused by pinctrl call
ARM: PRIMA2: select PINCTRL and PINCTRL_SIRF in Kconfig
ARM: nomadik: enable PINCTRL_NOMADIK where needed
ARM: mxs: enable pinctrl support
video: mxsfb: adopt pinctrl support
ASoC: mxs-saif: adopt pinctrl support
i2c: mxs: adopt pinctrl support
mtd: nand: gpmi: adopt pinctrl support
mmc: mxs-mmc: adopt pinctrl support
serial: mxs-auart: adopt pinctrl support
serial: amba-pl011: adopt pinctrl support
spi/imx: adopt pinctrl support
i2c: imx: adopt pinctrl support
can: flexcan: adopt pinctrl support
net: fec: adopt pinctrl support
ARM: ux500: switch MSP to using pinctrl for pins
ARM: ux500: alter MSP registration to return a device pointer
ARM: ux500: switch to using pinctrl for uart0
ARM: ux500: delete custom pin control system
ARM: ux500: switch over to Nomadik pinctrl driver
...
Three new system-on-chip models are supported: the st-ericsson u9540
in ux500, the sam9n12 in at91 and the emma ev2 in shmobile.
Emma is a little bit special because it is completely unrelated to
the classic shmobile models, but the new Renesas rmobile SoCs are a
combination of things from both Emma and shmobile, so it was decided to
have them all live in one directory.
This also contains updates to existing shmobile soc code as well as some
related board changes due to dependencies.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJPuerfAAoJEIwa5zzehBx3hi4P/AsoiLW4VqN67zMmiaGC5Nwe
X5nAeaaU0Oo4I9W2QD37V0BShk+yOE9xx7I0TOx7xE6/DpkJ3DhNlUOIvJSbtVD9
vOHF0pSu4huwmqMQmSS8qk5imYMVNGcDmNPVJsPdMCpC2PeCjNY5PxzX4PA18GxZ
9WaPClAP2vqSf/WewiFs73HE70TPL9DuMnAaA2QLBfeu6Cj5K401sc0sdJnBKJFc
W7T8qo1LJ98wEWeGW1Qks2mhtwlRf3S20t6aYQi0Bm9znaHMRomdaWdkrXLUYxiO
l8EHkCzgggXhdaqvqp15M3AFGgDsw+713UQ0n7tMGvIXv+Oc9ctriK0vcjIXHzH/
Ifz+4KvqYPo47ha0vSUpoRx29ThXO/zKDlzOUdh48JUWqBN6IDw+5H93ghI5SWGu
2h9RuAHIRxumtVe1Qb2dh2SzByxfqJJs7fkASXqWfucYgEi4vhylQdS7akCZ5ycq
35MOTS3v8rwxemTAR0NZKguRwVfUDnHGpyehumY5b/dp8nF0uHNaF8dRpnDC04Ty
4AHSquNmujQ0fqSJfcDCNT9V4vhrbdnW0YqhpCNFYLWBWnybJwjWDriWgt3Cc9tL
BMApWGprknKjxH/LeoZHIr0cHGjhZ0iRgoX+av7mPbNUcW/T64HEIs1Yyo4dbE2w
ffQN5xWomW+8VdZ1qf+w
=5TAz
-----END PGP SIGNATURE-----
Merge tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull support for new arm SoCs from Olof Johansson:
"Three new system-on-chip models are supported: the st-ericsson u9540
in ux500, the sam9n12 in at91 and the emma ev2 in shmobile.
Emma is a little bit special because it is completely unrelated to the
classic shmobile models, but the new Renesas rmobile SoCs are a
combination of things from both Emma and shmobile, so it was decided
to have them all live in one directory.
This also contains updates to existing shmobile soc code as well as
some related board changes due to dependencies."
* tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (23 commits)
mach-shmobile: Use DT_MACHINE for KZM9D V3
mach-shmobile: Emma Mobile EV2 DT support V3
mach-shmobile: KZM9D board Ethernet support V3
mach-shmobile: Emma Mobile EV2 GPIO support V3
mach-shmobile: Emma Mobile EV2 SMP support V3
mach-shmobile: KZM9D board support V3
mach-shmobile: Emma Mobile EV2 SoC base support V3
gpio: Emma Mobile GPIO driver V2
ARM: mach-shmobile: sh73a0: fixup PINT/IRQ16-IRQ31 irq number conflict
ARM: mach-shmobile: clock-r8a7740: use followparent_recalc on usb24s
ARM: mach-shmobile: clock-r8a7740: add MMCIF clock
ARM: mach-shmobile: clock-r8a7740: add SDHI clock
ARM: mach-shmobile: clock-r8a7740: add USB clock
ARM: mach-shmobile: clock-r8a7740: add FSI clock
ARM: mach-shmobile: r8a7740: cleanup I2C workaround method
ARM: mach-shmobile: r8a7740: add gpio_irq support
ARM: mach-shmobile: sh7372: Add FSI DMAEngine support
ARM / mach-shmobile: Use preset_lpj with calibrate_delay()
ARM: ux500: ioremap differences for DB9540
ARM: ux500: core U9540 support
...
The spear3xx, lpc32xx, shmobile and mmp platforms are joining the game of
booting using device trees, which is a great step forward for them. at91
and spear have pretty much completed this process with a huge amount of
work being put into at91. The other platforms are continuing the process.
We finally start to see the payback on this investment, as new machines
are getting supported purely by adding a .dts source file that can be
completely independent of the kernel source.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=7DYv
-----END PGP SIGNATURE-----
Merge tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull device tree conversions for arm-soc, part 1, from Olof Johansson:
"The spear3xx, lpc32xx, shmobile and mmp platforms are joining the game
of booting using device trees, which is a great step forward for them.
at91 and spear have pretty much completed this process with a huge
amount of work being put into at91. The other platforms are
continuing the process.
We finally start to see the payback on this investment, as new
machines are getting supported purely by adding a .dts source file
that can be completely independent of the kernel source."
Fix up trivial conflict in arch/arm/Kconfig
* tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (83 commits)
ARM: at91: Add ADC driver to at91sam9260/at91sam9g20 dtsi files
arm/dts: omap4-panda: Add LEDs support
arm/dts: omap4-sdp: Add LEDs support
arm/dts: twl4030: Add twl4030-gpio node
OMAP4: devices: Do not create mcpdm device if the dtb has been provided
OMAP4: devices: Do not create dmic device if the dtb has been provided
Documentation: update docs for mmp dt
ARM: dts: refresh dts file for arch mmp
ARM: mmp: support pxa910 with device tree
ARM: mmp: support mmp2 with device tree
gpio: pxa: parse gpio from DTS file
ARM: mmp: support DT in timer
ARM: mmp: support DT in irq
ARM: mmp: append CONFIG_MACH_MMP2_DT
ARM: mmp: fix build issue on mmp with device tree
ARM: ux500: Enable PRCMU Timer 4 (clocksource) for Device Tree
ARM: ux500: Disable SMSC911x platform code registration when DT is enabled
ARM: ux500: Fork cpu-db8500 platform_devs for sequential DT enablement
ARM: ux500: Do not attempt to register non-existent i2c devices on Snowball
ARM: SPEAr3xx: Correct keyboard data passed from DT
...
These cleanups are basically all over the place. The idea is to collect
changes with minimal impact but large number of changes so we can avoid
them from distracting in the diffstat in the other series.
A significant number of lines get removed here, in particular because
the ixp2000 and ixp23xx platforms get removed. These have never been
extremely popular and have fallen into disuse over time with no active
maintainer taking care of them. The u5500 soc never made it into a
product, so we are removing it from the ux500 platform.
Many good cleanups also went into the at91 and omap platforms, as has
been the case for a number of releases.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Hcjs
-----END PGP SIGNATURE-----
Merge tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull first batch of arm-soc cleanups from Olof Johansson:
"These cleanups are basically all over the place. The idea is to
collect changes with minimal impact but large number of changes so we
can avoid them from distracting in the diffstat in the other series.
A significant number of lines get removed here, in particular because
the ixp2000 and ixp23xx platforms get removed. These have never been
extremely popular and have fallen into disuse over time with no active
maintainer taking care of them. The u5500 soc never made it into a
product, so we are removing it from the ux500 platform.
Many good cleanups also went into the at91 and omap platforms, as has
been the case for a number of releases."
Trivial modify-delete conflicts in arch/arm/mach-{ixp2000,ixp23xx}
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (152 commits)
ARM: clps711x: Cleanup IRQ handling
ARM clps711x: Removed unused header mach/time.h
ARM: clps711x: Added note about support EP731x CPU to Kconfig
ARM: clps711x: Added missing register definitions
ARM: clps711x: Used own subarch directory for store header file
Dove: Fix Section mismatch warnings
ARM: orion5x: ts78xx debugging changes
ARM: orion5x: remove PM dependency from ts78xx
ARM: orion5x: ts78xx fix NAND resource off by one
ARM: orion5x: ts78xx whitespace cleanups
Orion5x: Fix Section mismatch warnings
Orion5x: Fix warning: struct pci_dev declared inside paramter list
ARM: clps711x: Combine header files into one for clps711x-targets
ARM: S3C24XX: Use common macro to define resources on mach-qt2410.c
ARM: S3C24XX: Use common macro to define resources on mach-osiris.c
ARM: EXYNOS: Adapt to cpuidle core time keeping and irq enable
ARM: S5PV210: Use common macro to define resources on mach-smdkv210.c
ARM: S5PV210: Use common macro to define resources on dev-audio.c
ARM: S5PC100: Use common macro to define resources on dev-audio.c
ARM: S5P64X0: Use common macro to define resources on dev-audio.c
...
* Added extra regs for A15 VGIC
* Added A15 architected timer node
* Split A5 and A9 TWD nodes into two separate ones for timer
and watchdog; interrupt definitions fixed on the way
* Fixed typo in A5 GIC compatible value
All the changes courtesy of Marc Zyngier.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
* 'emev2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/renesas:
mach-shmobile: Use DT_MACHINE for KZM9D V3
mach-shmobile: Emma Mobile EV2 DT support V3
mach-shmobile: KZM9D board Ethernet support V3
mach-shmobile: Emma Mobile EV2 GPIO support V3
mach-shmobile: Emma Mobile EV2 SMP support V3
mach-shmobile: KZM9D board support V3
mach-shmobile: Emma Mobile EV2 SoC base support V3
gpio: Emma Mobile GPIO driver V2
EXYNOS5250 includes a interrupt combiner controller that can group
upto 8 interrupts from different sources and deliver a single combined
interrupt to the GIC. Add a node for the interrupt combiner controller
in the device tree source file.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This should help the merge with the at91 adc driver that is currently
in the staging tree.
* at91/dt:
ARM: at91: Add ADC driver to at91sam9260/at91sam9g20 dtsi files
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Now that the bulk of at91sam9g20-related nodes are located in at91sam9260.dtsi,
we have to re-create the path to this ADC node for SoC specific parts.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Use DT_MACHINE_START() on the emev2 based KZM9D board.
Also include a tiny DTS file to describe the board and
update the Kconfig dependencies to select CONFIG_USE_OF.
Update the SMP glue code to use OF for matching.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
This is EMEV2 DT support V3. The support is limited to
whatever devices that are complied in the kernel. At this
point we have UARTs handled by "em-uart" and a timer
handled by "em-sti". Clocks and SMP are not supported.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
