Convert fan display function macros into functions to reduce
code size and improve code readability.
Code size reduction is about 200 bytes on x86_64.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Convert voltage display function macros into functions to reduce
code size and improve code readability.
Code size reduction is about 600 bytes on x86_64.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Convert temperature display function macros into functions to reduce
code size and improve code readability.
Code size reduction is about 2k on x86_64.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
TEMP_FROM_REG gets 12 bits of temperature data in the upper 12 bit
of a signed 16 bit parameter, with the integer part (including sign)
in the upper 8 bit and the remainder in bit 4..7. The lower 4 bit of
the 16 bit data is always 0. We can use that information to convert
the temperature directly into display data (1/1000th of degree C).
Note that the stored temperature data is not shifted right as the
comment claimed, so remove that misleading comment.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use devm_hwmon_device_register_with_groups API to attach attributes
to hwmon device, simplify code, and reduce code size.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use devm_hwmon_device_register_with_groups API to attach attributes
to hwmon device, simplify code, and reduce code size.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Function macros make the code larger and difficult ro read.
Drop them and reduce code size (on x86_64) by ~1800 bytes.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Forward declarations are unnecessary and easy to avoid, so rearrange
code and drop them.
No functional change.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The overtemperature status bit, which is used to display critical alarm status,
matches the output of the OVERT signal 1:1. If that signal is active-low, the
bit will read 1 if there is no alarm. It is therefore necessary to reverse
the bit in this case.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Also fix links to datasheets for other supported sensors from
ST Microelectronics, and add links to several Atmel datasheets.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
EMC1412, EMC1413, and EMC1414 are fully compatible to EMC1402, EMC1403,
and EMC1404, and even report the same chip ID. Add to device ID table
to enable instantiation with correct chip names.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Writing the hysteresis limit returned -ERANGE if the written hysteresis
was too high or too low. Relax error check and adjust the hysteresis
value to its valid range.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
All chips in this chip series only support a single hysteresis value. Having
multiple writable hysteresis attributes is therefore confusing, since a single
write affects all hysteresis temperatures. Make all but one (temp1_crit_hyst)
read-only.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Alarm and fault status register on EMC1402, EMC1412, and EMC1422 is reported
in a different register than with other chips. Add support for it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for emc1402/emc1412/emc1422 temperature monitoring chips.
This line of sensors only has 2 temperature channels (internal and external)
in comparison to the emc14x3 (3 channels) and emc14x4 (4 channels).
Signed-off-by: Josef Gajdusek <atx@atx.name>
[Guenter Roeck: ordered i2c address list, updated description/headline]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Make of_device_id array const, because all OF functions
handle it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Make of_device_id array const, because all OF functions
handle it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Make of_device_id array const, because all OF functions
handle it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Jean Delvare <jdelvare@suse.de>
Acked-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use devm_hwmon_device_register_with_groups API to attach attributes
to hwmon device, simplify code, and reduce code size.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Function macros obfuscate code and increase code size, so drop them.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use devm_hwmon_device_register_with_groups API to attach attributes
to hwmon device, simplify code, and reduce code size.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Function macros make the code harder to read and increase code size,
so drop them.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Updating the hysteresis value when updating the critical temperature limit
was following the rule of 'least surprise'. However, it had the undesirable
side effect of changing the hysteresis for all other attributes, which
defeats the purpose of least surprise. In addition, it could result in
invalid hysteresis values if the resulting hysteresis was too large. In such
cases the resulting hysteresis ended up changed anyway, which again defeats
the purpose. So drop that code and document the new behavior.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Forward declarations are easy to avoid and unnecessary.
Rearrange code to avoid it.
No functional change.
Acked-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The FSF mailing address changes over time, so drop it.
No functional change.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use devm_hwmon_device_register_with_groups API to attach attributes
to hwmon device, simplify code, and reduce code size.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The pointer to client->dev is used several times in the probe function.
Simplify code by introducing a separate variable for it.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use devm_hwmon_device_register_with_groups API to attach attributes
to hwmon device, simplify code, and reduce code size.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Components of the Versatile Express platform (configuration
microcontrollers on motherboard and daughterboards in particular)
talk to each other over a custom configuration bus. They
provide miscellaneous functions (from clock generator control
to energy sensors) which are represented as platform devices
(and Device Tree nodes). The transactions on the bus can
be generated by different "bridges" in the system, some
of which are universal for the whole platform (for the price
of high transfer latencies), others restricted to a subsystem
(but much faster).
Until now drivers for such functions were using custom "func"
API, which is being replaced in this patch by regmap calls.
This required:
* a rework (and move to drivers/bus directory, as suggested
by Samuel and Arnd) of the config bus core, which is much
simpler now and uses device model infrastructure (class)
to keep track of the bridges; non-DT case (soon to be
retired anyway) is simply covered by a special device
registration function
* the new config-bus driver also takes over device population,
so there is no need for special matching table for
of_platform_populate nor "simple-bus" hack in the arm64
model dtsi file (relevant bindings documentation has
been updated); this allows all the vexpress devices
fit into normal device model, making it possible
to remove plenty of early inits and other hacks in
the near future
* adaptation of the syscfg bridge implementation in the
sysreg driver, again making it much simpler; there is
a special case of the "energy" function spanning two
registers, where they should be both defined in the tree
now, but backward compatibility is maintained in the code
* modification of the relevant drivers:
* hwmon - just a straight-forward API change
* power/reset driver - API change
* regulator - API change plus error handling
simplification
* osc clock driver - this one required larger rework
in order to turn in into a standard platform driver
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Acked-by: Mark Brown <broonie@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Mike Turquette <mturquette@linaro.org>
The datasheet for EMC1413/EMC1414, which is fully compatible to
EMC1403/1404 and uses the same chip identification, references revision
numbers 0x01, 0x03, and 0x04. Accept the full range of revision numbers
from 0x01 to 0x04 to make sure none are missed.
Signed-off-by: Josef Gajdusek <atx@atx.name>
Cc: stable@vger.kernel.org
[Guenter Roeck: Updated headline and description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Commit 454aee17f claims to convert driver emc1403 to use
devm_hwmon_device_register_with_groups, however the patch itself makes
use of hwmon_device_register_with_groups instead. As the driver remove
function was still dropped, the hwmon device is no longer unregistered
on driver removal, leading to a resource leak.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Fixes: 454aee17f hwmon: (emc1403) Convert to use devm_hwmon_device_register_with_groups
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: stable@vger.kernel.org [3.13+]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Attempts to set the hysteresis value to a temperature below the target
limit fails with "write error: Numerical result out of range" due to
an inverted comparison.
Signed-off-by: Josef Gajdusek <atx@atx.name>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Cc: stable@vger.kernel.org
[Guenter Roeck: Updated headline and description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This reverts commit 9fb6c9c73b.
Tjmax on some Intel CPUs is below 85 degrees C. One known example is
L5630 with Tjmax of 71 degrees C. There are other Xeon processors with
Tjmax of 70 or 80 degrees C. Also, the Intel IA32 System Programming
document states that the temperature target is in bits 23:16 of MSR 0x1a2
(MSR_TEMPERATURE_TARGET), which is 8 bits, not 7.
So even if turbostat uses similar checks to validate Tjmax, there is no
evidence that the checks are actually required. On the contrary, the
checks are known to cause problems and therefore need to be removed.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=75071.
Fixes: 9fb6c9c hwmon: (coretemp) Refine TjMax detection
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Cc: stable@vger.kernel.org # 3.14+
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
An implementation error should not crash the kernel if it is avoidable.
Replace BUG() with WARN_ONCE().
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The 'label' attribute was always created but returned -ENOENT
if there is no label and such behaviour is undefined from
libsensors' point of view.
Fixed by providing is_visible method in the attributes group,
so the attribute is not created at all when unnecessary.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver used to directly us a DT 'compatible' property for
the 'name' attribute of the hwmon devices. Unfortunately it
contains '-' which is illegal in this context. It messes up
libsensors and thus every application using it.
Fixed by providing equivalent (and simpler) name strings.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Pull more powerpc updates from Ben Herrenschmidt:
"Here are a few more powerpc things for you.
So you'll find here the conversion of the two new firmware sysfs
interfaces to the new API for self-removing files that Greg and Tejun
introduced, so they can finally remove the old one.
I'm also reverting the hwmon driver for powernv. I shouldn't have
merged it, I got a bit carried away here. I hadn't realized it was
never CCed to the relevant maintainer(s) and list(s), and happens to
have some issues so I'm taking it out and it will come back via the
proper channels.
The rest is a bunch of LE fixes (argh, some of the new stuff was
broken on LE, I really need to start testing LE myself !) and various
random fixes here and there.
Finally one bit that's not strictly a fix, which is the HVC OPAL
change to "kick" the HVC thread when the firmware tells us there is
new incoming data. I don't feel like waiting for this one, it's
simple enough, and it makes a big difference in console responsiveness
which is good for my nerves"
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (26 commits)
powerpc/powernv Adapt opal-elog and opal-dump to new sysfs_remove_file_self
Revert "powerpc/powernv: hwmon driver for power values, fan rpm and temperature"
power, sched: stop updating inside arch_update_cpu_topology() when nothing to be update
powerpc/le: Avoid creatng R_PPC64_TOCSAVE relocations for modules.
arch/powerpc: Use RCU_INIT_POINTER(x, NULL) in platforms/cell/spu_syscalls.c
powerpc/opal: Add missing include
powerpc: Convert last uses of __FUNCTION__ to __func__
powerpc: Add lq/stq emulation
powerpc/powernv: Add invalid OPAL call
powerpc/powernv: Add OPAL message log interface
powerpc/book3s: Fix mc_recoverable_range buffer overrun issue.
powerpc: Remove dead code in sycall entry
powerpc: Use of_node_init() for the fakenode in msi_bitmap.c
powerpc/mm: NUMA pte should be handled via slow path in get_user_pages_fast()
powerpc/powernv: Fix endian issues with sensor code
powerpc/powernv: Fix endian issues with OPAL async code
tty/hvc_opal: Kick the HVC thread on OPAL console events
powerpc/powernv: Add opal_notifier_unregister() and export to modules
powerpc/ppc64: Do not turn AIL (reloc-on interrupts) too early
powerpc/ppc64: Gracefully handle early interrupts
...
This reverts commit 0de7f8a917.
This driver wasn't merged via the proper maintainers (my fault ... ooops !)
and has serious issues so let's take it out for now and have a new better
one be merged the right way
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
---
The purpose of this single series of commits from Srivatsa S Bhat (with
a small piece from Gautham R Shenoy) touching multiple subsystems that use
CPU hotplug notifiers is to provide a way to register them that will not
lead to deadlocks with CPU online/offline operations as described in the
changelog of commit 93ae4f978c (CPU hotplug: Provide lockless versions
of callback registration functions).
The first three commits in the series introduce the API and document it
and the rest simply goes through the users of CPU hotplug notifiers and
converts them to using the new method.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=SW7Q
-----END PGP SIGNATURE-----
Merge tag 'cpu-hotplug-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull CPU hotplug notifiers registration fixes from Rafael Wysocki:
"The purpose of this single series of commits from Srivatsa S Bhat
(with a small piece from Gautham R Shenoy) touching multiple
subsystems that use CPU hotplug notifiers is to provide a way to
register them that will not lead to deadlocks with CPU online/offline
operations as described in the changelog of commit 93ae4f978c ("CPU
hotplug: Provide lockless versions of callback registration
functions").
The first three commits in the series introduce the API and document
it and the rest simply goes through the users of CPU hotplug notifiers
and converts them to using the new method"
* tag 'cpu-hotplug-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (52 commits)
net/iucv/iucv.c: Fix CPU hotplug callback registration
net/core/flow.c: Fix CPU hotplug callback registration
mm, zswap: Fix CPU hotplug callback registration
mm, vmstat: Fix CPU hotplug callback registration
profile: Fix CPU hotplug callback registration
trace, ring-buffer: Fix CPU hotplug callback registration
xen, balloon: Fix CPU hotplug callback registration
hwmon, via-cputemp: Fix CPU hotplug callback registration
hwmon, coretemp: Fix CPU hotplug callback registration
thermal, x86-pkg-temp: Fix CPU hotplug callback registration
octeon, watchdog: Fix CPU hotplug callback registration
oprofile, nmi-timer: Fix CPU hotplug callback registration
intel-idle: Fix CPU hotplug callback registration
clocksource, dummy-timer: Fix CPU hotplug callback registration
drivers/base/topology.c: Fix CPU hotplug callback registration
acpi-cpufreq: Fix CPU hotplug callback registration
zsmalloc: Fix CPU hotplug callback registration
scsi, fcoe: Fix CPU hotplug callback registration
scsi, bnx2fc: Fix CPU hotplug callback registration
scsi, bnx2i: Fix CPU hotplug callback registration
...
Pull hwmon updates from Jean Delvare:
"This includes a number of driver conversions to
devm_hwmon_device_register_with_groups, a few cleanups, and
support for the ITE IT8623E"
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
hwmon: (it87) Add support for IT8623E
hwmon: (it87) Fix IT8603E define name
hwmon: (lm90) Convert to use hwmon_device_register_with_groups
hwmon: (lm90) Create all sysfs groups in one call
hwmon: (lm90) Always use the dev variable in the probe function
hwmon: (lm90) Create most optional attributes with sysfs_create_group
hwmon: Avoid initializing the same field twice
hwmon: (pc87360) Avoid initializing the same field twice
hwmon: (lm80) Convert to use devm_hwmon_device_register_with_groups
hwmon: (adm1021) Convert to use devm_hwmon_device_register_with_groups
hwmon: (lm63) Avoid initializing the same field twice
hwmon: (lm63) Convert to use devm_hwmon_device_register_with_groups
hwmon: (lm63) Create all sysfs groups in one call
hwmon: (lm63) Introduce 'dev' variable to point to client->dev
hwmon: (lm63) Add additional sysfs group for temp2_type attribute
hwmon: (f71805f) Fix author's address
Add support for the IT8623E found on Asus motherboards. It has same
hardware monitoring block as IT8603E.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Create all sysfs groups in one call by using sysfs_create_groups
instead of calling sysfs_create_group individually for each group.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
With the new hwmon API, all attributes have to be created as groups.
Use sysfs_create_group and sysfs_remove_group instead of device_create_file
and device_remove_file to prepare for the new API.
Exception is the 'pec' attribute which will stay with the i2c device.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
All hwmon drivers allocate their data structure with some form of
kzalloc, so setting data fields to zero explicitly is a waste of time.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
data is kzalloc'd, so data->valid, data->innr and data->tempnr are
already 0. Also rework the initialization path to only set name and
data->fannr once.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
We can create all sysfs groups in one call by using sysfs_create_groups
instead of using sysfs_create_group individually for each group.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
client->dev is used multiple times in several functions.
Introduce dev variable pointing to it to simplify the code.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
With the new hwmon API, we can only add groups of attributes, not individual
attributes. To prepare for the use of the new API, add an additional sensor
group for the temp2_type attribute and register it with sysfs_create_group
instead of device_create_file.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
The original address was incomplete, and this caused it to be missed
by the recent update to my new address.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Adding new PCI ID to support AMD F16 M30h processor (Mullins).
While at it, modify Kconfig and Doc files to reflect the
support for newer processors
Note: PCI ID for this processor will make it into pci_ids.h
as part of this patch:
http://marc.info/?l=linux-kernel&m=139291362126057&w=2
which should be pulled into 3.15 when merge window opens
(It currently sits in 'for-next' branch of bp.git-
https://git.kernel.org/cgit/linux/kernel/git/bp/bp.git/log/?h=for-next)
Signed-off-by: Aravind Gopalakrishnan <Aravind.Gopalakrishnan@amd.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Pull main powerpc updates from Ben Herrenschmidt:
"This time around, the powerpc merges are going to be a little bit more
complicated than usual.
This is the main pull request with most of the work for this merge
window. I will describe it a bit more further down.
There is some additional cpuidle driver work, however I haven't
included it in this tree as it depends on some work in tip/timer-core
which Thomas accidentally forgot to put in a topic branch. Since I
didn't want to carry all of that tip timer stuff in powerpc -next, I
setup a separate branch on top of Thomas tree with just that cpuidle
driver in it, and Stephen has been carrying that in next separately
for a while now. I'll send a separate pull request for it.
Additionally, two new pieces in this tree add users for a sysfs API
that Tejun and Greg have been deprecating in drivers-core-next.
Thankfully Greg reverted the patch that removes the old API so this
merge can happen cleanly, but once merged, I will send a patch
adjusting our new code to the new API so that Greg can send you the
removal patch.
Now as for the content of this branch, we have a lot of perf work for
power8 new counters including support for our new "nest" counters
(also called 24x7) under pHyp (not natively yet).
We have new functionality when running under the OPAL firmware
(non-virtualized or KVM host), such as access to the firmware error
logs and service processor dumps, system parameters and sensors, along
with a hwmon driver for the latter.
There's also a bunch of bug fixes accross the board, some LE fixes,
and a nice set of selftests for validating our various types of copy
loops.
On the Freescale side, we see mostly new chip/board revisions, some
clock updates, better support for machine checks and debug exceptions,
etc..."
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (70 commits)
powerpc/book3s: Fix CFAR clobbering issue in machine check handler.
powerpc/compat: 32-bit little endian machine name is ppcle, not ppc
powerpc/le: Big endian arguments for ppc_rtas()
powerpc: Use default set of netfilter modules (CONFIG_NETFILTER_ADVANCED=n)
powerpc/defconfigs: Enable THP in pseries defconfig
powerpc/mm: Make sure a local_irq_disable prevent a parallel THP split
powerpc: Rate-limit users spamming kernel log buffer
powerpc/perf: Fix handling of L3 events with bank == 1
powerpc/perf/hv_{gpci, 24x7}: Add documentation of device attributes
powerpc/perf: Add kconfig option for hypervisor provided counters
powerpc/perf: Add support for the hv 24x7 interface
powerpc/perf: Add support for the hv gpci (get performance counter info) interface
powerpc/perf: Add macros for defining event fields & formats
powerpc/perf: Add a shared interface to get gpci version and capabilities
powerpc/perf: Add 24x7 interface headers
powerpc/perf: Add hv_gpci interface header
powerpc: Add hvcalls for 24x7 and gpci (Get Performance Counter Info)
sysfs: create bin_attributes under the requested group
powerpc/perf: Enable BHRB access for EBB events
powerpc/perf: Add BHRB constraint and IFM MMCRA handling for EBB
...
This patch adds basic kernel enablement for reading power values, fan
speed rpm and temperature values on powernv platforms which will
be exported to user space through sysfs interface.
Signed-off-by: Shivaprasad G Bhat <sbhat@linux.vnet.ibm.com>
Signed-off-by: Neelesh Gupta <neelegup@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Subsystems that want to register CPU hotplug callbacks, as well as perform
initialization for the CPUs that are already online, often do it as shown
below:
get_online_cpus();
for_each_online_cpu(cpu)
init_cpu(cpu);
register_cpu_notifier(&foobar_cpu_notifier);
put_online_cpus();
This is wrong, since it is prone to ABBA deadlocks involving the
cpu_add_remove_lock and the cpu_hotplug.lock (when running concurrently
with CPU hotplug operations).
Instead, the correct and race-free way of performing the callback
registration is:
cpu_notifier_register_begin();
for_each_online_cpu(cpu)
init_cpu(cpu);
/* Note the use of the double underscored version of the API */
__register_cpu_notifier(&foobar_cpu_notifier);
cpu_notifier_register_done();
Fix the hwmon via-cputemp code by using this latter form of callback
registration.
Cc: Jean Delvare <jdelvare@suse.de>
Cc: Ingo Molnar <mingo@kernel.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Subsystems that want to register CPU hotplug callbacks, as well as perform
initialization for the CPUs that are already online, often do it as shown
below:
get_online_cpus();
for_each_online_cpu(cpu)
init_cpu(cpu);
register_cpu_notifier(&foobar_cpu_notifier);
put_online_cpus();
This is wrong, since it is prone to ABBA deadlocks involving the
cpu_add_remove_lock and the cpu_hotplug.lock (when running concurrently
with CPU hotplug operations).
Instead, the correct and race-free way of performing the callback
registration is:
cpu_notifier_register_begin();
for_each_online_cpu(cpu)
init_cpu(cpu);
/* Note the use of the double underscored version of the API */
__register_cpu_notifier(&foobar_cpu_notifier);
cpu_notifier_register_done();
Fix the hwmon coretemp code by using this latter form of callback
registration.
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Jean Delvare <jdelvare@suse.de>
Cc: Ingo Molnar <mingo@kernel.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The chip's programming interface is quite similar to LTC3880
and supports the same set of sensors.
Reviewed-by: Robert Coulson <rob.coulson@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
LTC2974 datasheet revision C lists the chip ID for LTC2974 as 0x0213.
Reviewed-by: Robert Coulson <rob.coulson@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
hwmon name attributes must not include '-', as specified in
Documentation/hwmon/sysfs-interface. Also filter out spaces,
tabs, wildcards, and newline characters.
Tested-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use SIMPLE_DEV_PM_OPS macro in order to make the code simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The hysteresis register is shared among both temperature sensors.
This means changing one also affects the other. To avoid confusion,
established way to express this is to make only the first instance writable
and keep all other instances as read-only. Otherwise users may be
confused that changing the second writable value also affects the first,
while it is more obvious that a writable value may affect a different
read-only value.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
It doesn't provide value to get a log message whenever the driver
updates its cached data, so drop the message.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Hysteresis temperatures are defined as absolute temperatures,
not as delta value from the critical temperatures.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Introduce local variable 'dev' in probe function to make code easier
to read. Also drop dev_info message in probe to reduce noisiness
during boot.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Simplify code, reduce code size, and attach sensor attributes
to hwmon device.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Simplify code, reduce code size, and attach sysfs attributes to hwmon device.
For this driver, the only attribute created is the name attribute.
Other attributes are still created and removed dynamically as cores
are added or removed.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Tested-by: Jean Delvare <jdelvare@suse.de>
This simplifies error handling.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Tested-by: Jean Delvare <jdelvare@suse.de>
Instead of creating each attribute individually, use sysfs_create_group
to create all attributes for one core with a single call.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Tested-by: Jean Delvare <jdelvare@suse.de>
Devicetree functions are stubbed out if CONFIG_OF is undefined.
Therefore, conditional compilation is unnecessary and can be removed.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
The debug messages in this driver have little if any value. Drop them.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
i2c_smbus_write_byte_data returns a valid error code.
Return it to the user instead of replacing it with -EIO.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
ADC128D818 is a System Monitor with Temperature Sensor. It is similar to LM80
and LM96080, but has 16 bit wide sensor registers and no fan speed monitoring.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Entries have been added at more or less random positions over time, so
it becomes difficult to find what you are looking for or figure out
where to insert new entries.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
data is kzalloc'd, so data->valid and data->model are already 0.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
There is no reason to replace one error with another.
smatch message:
drivers/hwmon/emc2103.c:352 set_fan_div() info: why not propagate 'status'
from i2c_smbus_read_byte_data() instead of (-5)?
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
There is no reason to replace one error code with another,
and returning -1 as error code is wrong anyway.
Smatch log:
drivers/hwmon/smm665.c:225 smm665_read_adc() info: why not propagate 'rv'
from i2c_smbus_read_word_swapped() instead of (-1)?
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use devm_ioremap_resource() in order to make the code simpler,
and move 'struct resource *mem' from 'struct jz4740_hwmon' to
jz4740_hwmon_probe() because the 'mem' variable is used only in
jz4740_hwmon_probe(). Also the redundant return value check of
platform_get_resource() is removed, because the value is checked
by devm_ioremap_resource().
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
LTC4260 is a Positive Voltage Hot Swap Controller.
The driver currently only supports voltage monitoring, not voltage control.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Driver Linear Technologies LTC4222 Dual Hot Swap Controller
The driver currently only supports voltage monitoring, not voltage control.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
When trying to set the minimum temperature, the driver was erroneously
writing the maximum temperature into the chip.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cc: stable@vger.kernel.org # v3.2+
Reviewed-by: Jean Delvare <jdelvare@suse.de>
The ntc thermistor code was doing math whose temporary result might
have overflowed 32-bits. We need some casts in there to make it safe.
In one example I found:
- pullup_uV: 1800000
- result of iio_read_channel_raw: 3226
- 1800000 * 3226 => 0x15a1cbc80
Signed-off-by: Doug Anderson <dianders@chromium.org>
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Remove use of regmap_irq_get_virq() in driver probe which was
conflicting with use of platform_get_irq_byname().
platform_get_irq_byname() already returns the VIRQ number due
to MFD core translation so using regmap_irq_get_virq() on that
returned value results in an incorrect IRQ being requested.
The driver probes then fail because of this.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Some chips use different exponents for sensors on different pages
or rails. Detect and store exponent per page to support this situation.
This fixes a problem with wrong voltages seen on UCD90120.
Reported-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Tested-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Similar to what was done for the lm75 driver.
Add depends on THERMAL since that is what provides the
register/unregister functions above, but only if THERMAL_OF was
selected as this is an optional feature of the driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Eduardo Valentin <eduardo.valentin@ti.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Based on an earlier attempt by Randy Dunlap.
Fix SENSORS_LM75 dependencies to eliminate build errors:
drivers/built-in.o: In function `lm75_remove':
lm75.c:(.text+0x12bd8c): undefined reference to `thermal_zone_of_sensor_unregister'
drivers/built-in.o: In function `lm75_probe':
lm75.c:(.text+0x12c123): undefined reference to `thermal_zone_of_sensor_register'
Add depends on THERMAL since that is what provides the
register/unregister functions above, but only if THERMAL_OF was
selected as this is an optional feature of the driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Eduardo Valentin <eduardo.valentin@ti.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Pull hwmon updates from Jean Delvare:
"This include it87 driver improvements, and a tree-wide change of my
e-mail address"
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
Update Jean Delvare's e-mail address
hwmon: (it87) Print proper names for the IT8771E and IT8772E
hwmon: (it87) Add support for the ITE IT8603E
The driver prints IT8771F and IT8772F instead of IT8771E and IT8772E
respectively when the driver is loaded. This is a cosmetic only bug
but let's fix it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add support for IT8603E.
This closes bug #57861:
https://bugzilla.kernel.org/show_bug.cgi?id=57861
[JD: Fixes and clean-ups.]
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Pull thermal management updates from Zhang Rui:
"This time, the biggest change is the work of representing hardware
thermal properties in device tree infrastructure.
This work includes the introduction of a device tree bindings for
describing the hardware thermal behavior and limits, and also a parser
to read and interpret the data, and build thermal zones and thermal
binding parameters. It also contains three examples on how to use the
new representation on sensor devices, using three different drivers to
accomplish it. One driver is in thermal subsystem, the TI SoC
thermal, and the other two drivers are in hwmon subsystem.
Actually, this would be the first step of the complete work because we
still need to check other potential drivers to be converted and then
validate the proposed API. But the reason why I include it in this
pull request is that, first, this change does not hurt any others
without using this approach, second, the principle and concept of this
change would not break after converting the remaining drivers. BTW,
as you can see, there are several points in this change that do not
belong to thermal subsystem. Because it has been suggested by Guenter
R that in such cases, it is recommended to send the complete series
via one single subsystem.
Specifics:
- representing hardware thermal properties in device tree
infrastructure
- fix a regression that the imx thermal driver breaks system suspend.
- introduce ACPI INT3403 thermal driver to retrieve temperature data
from the INT3403 ACPI device object present on some systems.
- introduce debug statement for thermal core and step_wise governor.
- assorted fixes and cleanups for thermal core, cpu cooling, exynos
thrmal, intel powerclamp and imx thermal driver"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux: (34 commits)
thermal: remove const flag from .ops of imx thermal
Thermal: update thermal zone device after setting emul_temp
intel_powerclamp: Fix cstate counter detection.
thermal: imx: add necessary clk operation
Thermal cpu cooling: return error if no valid cpu frequency entry
thermal: fix cpu_cooling max_level behavior
thermal: rcar-thermal: Enable driver compilation with COMPILE_TEST
thermal: debug: add debug statement for core and step_wise
thermal: imx_thermal: add module device table
drivers: thermal: Mark function as static in x86_pkg_temp_thermal.c
thermal:samsung: fix compilation warning
thermal: imx: correct suspend/resume flow
thermal: exynos: fix error return code
Thermal: ACPI INT3403 thermal driver
MAINTAINERS: add thermal bindings entry in thermal domain
arm: dts: make OMAP4460 bandgap node to belong to OCP
arm: dts: make OMAP443x bandgap node to belong to OCP
arm: dts: add cooling properties on omap5 cpu node
arm: dts: add omap5 thermal data
arm: dts: add omap5 CORE thermal data
...
- ACPI core changes to make it create a struct acpi_device object for every
device represented in the ACPI tables during all namespace scans regardless
of the current status of that device. In accordance with this, ACPI hotplug
operations will not delete those objects, unless the underlying ACPI tables
go away.
- On top of the above, new sysfs attribute for ACPI device objects allowing
user space to check device status by triggering the execution of _STA for
its ACPI object. From Srinivas Pandruvada.
- ACPI core hotplug changes reducing code duplication, integrating the
PCI root hotplug with the core and reworking container hotplug.
- ACPI core simplifications making it use ACPI_COMPANION() in the code
"glueing" ACPI device objects to "physical" devices.
- ACPICA update to upstream version 20131218. This adds support for the
DBG2 and PCCT tables to ACPICA, fixes some bugs and improves debug
facilities. From Bob Moore, Lv Zheng and Betty Dall.
- Init code change to carry out the early ACPI initialization earlier.
That should allow us to use ACPI during the timekeeping initialization
and possibly to simplify the EFI initialization too. From Chun-Yi Lee.
- Clenups of the inclusions of ACPI headers in many places all over from
Lv Zheng and Rashika Kheria (work in progress).
- New helper for ACPI _DSM execution and rework of the code in drivers
that uses _DSM to execute it via the new helper. From Jiang Liu.
- New Win8 OSI blacklist entries from Takashi Iwai.
- Assorted ACPI fixes and cleanups from Al Stone, Emil Goode, Hanjun Guo,
Lan Tianyu, Masanari Iida, Oliver Neukum, Prarit Bhargava, Rashika Kheria,
Tang Chen, Zhang Rui.
- intel_pstate driver updates, including proper Baytrail support, from
Dirk Brandewie and intel_pstate documentation from Ramkumar Ramachandra.
- Generic CPU boost ("turbo") support for cpufreq from Lukasz Majewski.
- powernow-k6 cpufreq driver fixes from Mikulas Patocka.
- cpufreq core fixes and cleanups from Viresh Kumar, Jane Li, Mark Brown.
- Assorted cpufreq drivers fixes and cleanups from Anson Huang, John Tobias,
Paul Bolle, Paul Walmsley, Sachin Kamat, Shawn Guo, Viresh Kumar.
- cpuidle cleanups from Bartlomiej Zolnierkiewicz.
- Support for hibernation APM events from Bin Shi.
- Hibernation fix to avoid bringing up nonboot CPUs with ACPI EC disabled
during thaw transitions from Bjørn Mork.
- PM core fixes and cleanups from Ben Dooks, Leonardo Potenza, Ulf Hansson.
- PNP subsystem fixes and cleanups from Dmitry Torokhov, Levente Kurusa,
Rashika Kheria.
- New tool for profiling system suspend from Todd E Brandt and a cpupower
tool cleanup from One Thousand Gnomes.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=dRf6
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"As far as the number of commits goes, the top spot belongs to ACPI
this time with cpufreq in the second position and a handful of PM
core, PNP and cpuidle updates. They are fixes and cleanups mostly, as
usual, with a couple of new features in the mix.
The most visible change is probably that we will create struct
acpi_device objects (visible in sysfs) for all devices represented in
the ACPI tables regardless of their status and there will be a new
sysfs attribute under those objects allowing user space to check that
status via _STA.
Consequently, ACPI device eject or generally hot-removal will not
delete those objects, unless the table containing the corresponding
namespace nodes is unloaded, which is extremely rare. Also ACPI
container hotplug will be handled quite a bit differently and cpufreq
will support CPU boost ("turbo") generically and not only in the
acpi-cpufreq driver.
Specifics:
- ACPI core changes to make it create a struct acpi_device object for
every device represented in the ACPI tables during all namespace
scans regardless of the current status of that device. In
accordance with this, ACPI hotplug operations will not delete those
objects, unless the underlying ACPI tables go away.
- On top of the above, new sysfs attribute for ACPI device objects
allowing user space to check device status by triggering the
execution of _STA for its ACPI object. From Srinivas Pandruvada.
- ACPI core hotplug changes reducing code duplication, integrating
the PCI root hotplug with the core and reworking container hotplug.
- ACPI core simplifications making it use ACPI_COMPANION() in the
code "glueing" ACPI device objects to "physical" devices.
- ACPICA update to upstream version 20131218. This adds support for
the DBG2 and PCCT tables to ACPICA, fixes some bugs and improves
debug facilities. From Bob Moore, Lv Zheng and Betty Dall.
- Init code change to carry out the early ACPI initialization
earlier. That should allow us to use ACPI during the timekeeping
initialization and possibly to simplify the EFI initialization too.
From Chun-Yi Lee.
- Clenups of the inclusions of ACPI headers in many places all over
from Lv Zheng and Rashika Kheria (work in progress).
- New helper for ACPI _DSM execution and rework of the code in
drivers that uses _DSM to execute it via the new helper. From
Jiang Liu.
- New Win8 OSI blacklist entries from Takashi Iwai.
- Assorted ACPI fixes and cleanups from Al Stone, Emil Goode, Hanjun
Guo, Lan Tianyu, Masanari Iida, Oliver Neukum, Prarit Bhargava,
Rashika Kheria, Tang Chen, Zhang Rui.
- intel_pstate driver updates, including proper Baytrail support,
from Dirk Brandewie and intel_pstate documentation from Ramkumar
Ramachandra.
- Generic CPU boost ("turbo") support for cpufreq from Lukasz
Majewski.
- powernow-k6 cpufreq driver fixes from Mikulas Patocka.
- cpufreq core fixes and cleanups from Viresh Kumar, Jane Li, Mark
Brown.
- Assorted cpufreq drivers fixes and cleanups from Anson Huang, John
Tobias, Paul Bolle, Paul Walmsley, Sachin Kamat, Shawn Guo, Viresh
Kumar.
- cpuidle cleanups from Bartlomiej Zolnierkiewicz.
- Support for hibernation APM events from Bin Shi.
- Hibernation fix to avoid bringing up nonboot CPUs with ACPI EC
disabled during thaw transitions from Bjørn Mork.
- PM core fixes and cleanups from Ben Dooks, Leonardo Potenza, Ulf
Hansson.
- PNP subsystem fixes and cleanups from Dmitry Torokhov, Levente
Kurusa, Rashika Kheria.
- New tool for profiling system suspend from Todd E Brandt and a
cpupower tool cleanup from One Thousand Gnomes"
* tag 'pm+acpi-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (153 commits)
thermal: exynos: boost: Automatic enable/disable of BOOST feature (at Exynos4412)
cpufreq: exynos4x12: Change L0 driver data to CPUFREQ_BOOST_FREQ
Documentation: cpufreq / boost: Update BOOST documentation
cpufreq: exynos: Extend Exynos cpufreq driver to support boost
cpufreq / boost: Kconfig: Support for software-managed BOOST
acpi-cpufreq: Adjust the code to use the common boost attribute
cpufreq: Add boost frequency support in core
intel_pstate: Add trace point to report internal state.
cpufreq: introduce cpufreq_generic_get() routine
ARM: SA1100: Create dummy clk_get_rate() to avoid build failures
cpufreq: stats: create sysfs entries when cpufreq_stats is a module
cpufreq: stats: free table and remove sysfs entry in a single routine
cpufreq: stats: remove hotplug notifiers
cpufreq: stats: handle cpufreq_unregister_driver() and suspend/resume properly
cpufreq: speedstep: remove unused speedstep_get_state
platform: introduce OF style 'modalias' support for platform bus
PM / tools: new tool for suspend/resume performance optimization
ACPI: fix module autoloading for ACPI enumerated devices
ACPI: add module autoloading support for ACPI enumerated devices
ACPI: fix create_modalias() return value handling
...
Add new PCI ID to support new model "Kaveri" family.
Signed-off-by: Philip Pokorny <ppokorny@penguincomputing.com>
Cc: stable@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
After a suspend/resume cycle, the NCT6791 is back to its original BIOS
programming. In this state, HWMON IO access may be locked.
Re-enable it during resume.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Some Intel CPUs do not set the 'valid' bit in IA32_THERM_STATUS if the
temperature is too low to be measured. This condition will not change until
the CPU is hot enough for its temperature to be measured. Returning an error
in such conditions is not very useful. Drop checking the valid bit and just
return the reported temperature instead.
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The ADC resolution of the PMIC is 10-bits, this means that the maximum
possible value is 1023 and not the 1024 as originally in the code.
Signed-off-by: Anthony Olech <anthony.olech.opensource@diasemi.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Intel's turbostat code uses only 7 bits from MSR_IA32_TEMPERATURE_TARGET to
read TjMax, and also only accepts it if the reported temperature is at least
85 degrees C. Play safe and do the same.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Since we now have to use PCI IDs to detect CPU types anyway, use this mechanism
to detect CE41x0 CPUs. Advantage is that it only requires a single entry and
covers all variants of CE41x0, including those unknown to us.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Atom S12x0 CPUs are identified by the CPU host bridge ID. Add an override
table based on PCI IDs as well as code to detect it.
PCI access functions can now be called with PCI disabled, so unlike previous
attempts to use PCI IDs, the code no longer depends on it. If PCI is disabled,
the CPU will not be identified correctly. Since it is unlikely that anything
will work in this case, this is an acceptable limitation.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Don't use DEFINE_PCI_DEVICE_TABLE macro, because this macro
is not preferred.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
When the core number exceeds 9, the size of the buffer storing the
alarm attribute name is insufficient and the attribute name is
truncated. This causes libsensors to skip these attributes as the
truncated name is not recognized.
Reported-by: Andreas Hollmann <hollmann@in.tum.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
* acpi-cleanup: (22 commits)
ACPI / tables: Return proper error codes from acpi_table_parse() and fix comment.
ACPI / tables: Check if id is NULL in acpi_table_parse()
ACPI / proc: Include appropriate header file in proc.c
ACPI / EC: Remove unused functions and add prototype declaration in internal.h
ACPI / dock: Include appropriate header file in dock.c
ACPI / PCI: Include appropriate header file in pci_link.c
ACPI / PCI: Include appropriate header file in pci_slot.c
ACPI / EC: Mark the function acpi_ec_add_debugfs() as static in ec_sys.c
ACPI / NVS: Include appropriate header file in nvs.c
ACPI / OSL: Mark the function acpi_table_checksum() as static
ACPI / processor: initialize a variable to silence compiler warning
ACPI / processor: use ACPI_COMPANION() to get ACPI device
ACPI: correct minor typos
ACPI / sleep: Drop redundant acpi_disabled check
ACPI / dock: Drop redundant acpi_disabled check
ACPI / table: Replace '1' with specific error return values
ACPI: remove trailing whitespace
ACPI / IBFT: Fix incorrect <acpi/acpi.h> inclusion in iSCSI boot firmware module
ACPI / i915: Fix incorrect <acpi/acpi.h> inclusions via <linux/acpi_io.h>
SFI / ACPI: Fix warnings reported during builds with W=1
...
Conflicts:
drivers/acpi/nvs.c
drivers/hwmon/asus_atk0110.c
Fix HIH-6130 driver to work with BeagleBone
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJSqd02AAoJEMsfJm/On5mBrwoP/05UBS1HCf/yyX3FbnIOsjA6
oMOH3SkuzVWFQmndqANZS/oxwwnO3WZ4ML25b0GEYjJeCqf/JpVLyalRMjWV1Xxz
DqVRmd9yO9rrOuQ9CuSJqAqXzGnXNip16VIetArarcMtZrEUkkMqpY7ax8tGKr24
Q0zIWpG8XO7hykeOetUuwOk9bKD+iFX04ttQFWmv8Mlv/FR//khMRMnMyP0kOP3D
ZLtMoMi1vdsxMP5PZzgoijH5CgAgb2Eh+jilP2rLOh5R/IrZOyheGBtOYay5Rmg/
e7JL3ODHNPnBsIAT27Fk98PLHBAIrCELg0N5k1OvvrmjhSL4GZCVlwyOUn0AngIG
GQUWwvI7tdQgV3mftuIz3ueoHTEL+0Y9BISF9FX6DrXgq94Xrl3YnNzsTAvHQtun
yoB8W780j7cRIvEpi5jNjhESR9J13fSDbawAMFTUWsbZLN7lwp1KlUV5OryysizR
KIkoC9RGWbfl4tk5neD0bM9O3gpE7sctbRLPZkVahr1cslaXr0oP3zOQ1kAByWaI
4Li/JklmanERz+meP1DDdJ1VOlfM/GpiGNx0j0RNX4MlDWaX8s24fYEIs//R0j0H
QQ38YoO7OwVyscCn5HkAMTU3gn3evA4YAOgwAyyXUFMIwAQiMNTOJmsd6EAsKWpJ
jKnT7vIlfELjop48xwXu
=B6Bw
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fix from Guenter Roeck:
"Fix HIH-6130 driver to work with BeagleBone"
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: HIH-6130: Support I2C bus drivers without I2C_FUNC_SMBUS_QUICK
The "rpm * div" operations can overflow here, so this patch adds an
upper limit to rpm to prevent that. Jean Delvare helped me with this
patch.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Roger Lucas <vt8231@hiddenengine.co.uk>
Cc: stable@vger.kernel.org
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The W83L786NG stores the fan speed on 4 bits while the sysfs interface
uses a 0-255 range. Thus the driver should scale the user input down
to map it to the device range, and scale up the value read from the
device before presenting it to the user. The reserved register nibble
should be left unchanged.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
The wrong mask is used, which causes some fan speed control modes
(pwmX_enable) to be incorrectly reported, and some modes to be
impossible to set.
[JD: add subject and description.]
Signed-off-by: Brian Carnes <bmcarnes@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Some I2C bus drivers do not allow zero-length data transfers which are
required to start a measurement with the HIH6130/1 sensor. Nevertheless,
we can overcome this limitation by writing a zero dummy byte. This byte
is ignored by the sensor and was verified to be working with the OMAP
I2C bus driver in a BeagleBone board.
Signed-off-by: José Miguel Gonçalves <jose.goncalves@inov.pt>
[Guenter Roeck: Simplified complexity of write_length initialization]
Cc: stable@vger.kernel.org # v3.10+
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Replace direct inclusions of <acpi/acpi.h>, <acpi/acpi_bus.h> and
<acpi/acpi_drivers.h>, which are incorrect, with <linux/acpi.h>
inclusions and remove some inclusions of those files that aren't
necessary.
First of all, <acpi/acpi.h>, <acpi/acpi_bus.h> and <acpi/acpi_drivers.h>
should not be included directly from any files that are built for
CONFIG_ACPI unset, because that generally leads to build warnings about
undefined symbols in !CONFIG_ACPI builds. For CONFIG_ACPI set,
<linux/acpi.h> includes those files and for CONFIG_ACPI unset it
provides stub ACPI symbols to be used in that case.
Second, there are ordering dependencies between those files that always
have to be met. Namely, it is required that <acpi/acpi_bus.h> be included
prior to <acpi/acpi_drivers.h> so that the acpi_pci_root declarations the
latter depends on are always there. And <acpi/acpi.h> which provides
basic ACPICA type declarations should always be included prior to any other
ACPI headers in CONFIG_ACPI builds. That also is taken care of including
<linux/acpi.h> as appropriate.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com> (drivers/pci stuff)
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> (Xen stuff)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch adds to tmp102 temperature sensor the possibility
to expose itself as thermal zone device, registered on the
thermal framework.
The thermal zone is built only if a device tree node
describing a thermal zone for this sensor is present
inside the tmp102 DT node. Otherwise, the driver behavior
will be the same.
Note: This patch has also been reviewed by Jean D. He has
requested to perform a wider inspection of possible
users of thermal and hwmon interaction API. On the other
hand, the change on this patch is acceptable on first
step of overall code change.
Cc: Jean Delvare <khali@linux-fr.org>
Cc: lm-sensors@lm-sensors.org
Cc: linux-kernel@vger.kernel.org
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
This patch adds to lm75 temperature sensor the possibility
to expose itself as thermal zone device, registered on the
thermal framework.
The thermal zone is built only if a device tree node
describing a thermal zone for this sensor is present
inside the lm75 DT node. Otherwise, the driver behavior
will be the same.
Note: This patch has also been reviewed by Jean D. He has
requested to perform a wider inspection of possible
users of thermal and hwmon interaction API. On the other
hand, the change on this patch is acceptable on first
step of overall code change.
Cc: Jean Delvare <khali@linux-fr.org>
Cc: lm-sensors@lm-sensors.org
Cc: linux-kernel@vger.kernel.org
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
* acpica:
ACPI: Clean up incorrect inclusions of ACPICA headers
ACPICA: Update version to 20131115.
ACPICA: Add support to delete all objects attached to the root namespace node.
ACPICA: Delete all attached data objects during namespace node deletion.
ACPICA: Resources: Fix loop termination for the get AML length function.
ACPICA: Tests: Add CHECKSUM_ABORT protection for test utilities.
ACPICA: Debug output: Do not emit function nesting level for kernel build.
Header file <acpi/acpi.h> contains environemnt settings and architecture
specific implementation that should be included before any other ACPICA
headers in order to keep a consistent build environment for ACPICA users.
The following internal ACPICA header files should be included from
<acpi/acpi.h> and should not be included by other kernel files:
<acpi/acpiosxf.h>
<acpi/acpixf.h>
Clean up incorrect inclusions of these files from non-ACPICA source
files.
[rjw: Subject and changelog]
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Since acpi_bus_get_device() returns plain int and not acpi_status,
ACPI_FAILURE() should not be used for checking its return value. Fix
that.
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Unlike other chips supported by this driver, the NCT6791 only has a single
set of registers to configure weighted fan control. Enable it only for the
single channel supporting it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The number of SMIOVT registers on NCT6779 and NCT6791 is limited to 2.
As result, the driver may not report some of the temperatures used
for fan control. This can result in some of the pwmX_temp_sel or
pwm2_weight_temp_sel attributes to wrongly return 0.
Fortunately, the chip has registers to monitor those temperatures.
Add them to the list of temperatures to report.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This was tested on a NETGEAR ReadyNAS 2120 device (Marvell Armada XP
based board, via DT).
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Pull hwmon fixes and updates from Jean Delvare:
"All lm90 driver fixes and improvements"
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
Documentation: dt: hwmon: Add OF document for LM90
hwmon: (lm90) Add power control
hwmon: (lm90) Add support for TI TMP451
hwmon: (lm90) Use enums for the indexes of temp8 and temp11
hwmon: (lm90) Add support to handle IRQ
hwmon: (lm90) Define status bits
hwmon: (lm90) Fix max6696 alarm handling
The device lm90 can be controlled by the vcc rail.
Adding the regulator support to power on/off the vcc rail.
Enable the "vcc" regulator before accessing the device.
[JD: Rename variables to avoid confusion with registers.]
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
TI TMP451 is mostly compatible with ADT7461, except for
local temperature low byte and max conversion rate.
Add support to the LM90 driver.
Signed-off-by: Wei Ni <wni@nvidia.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Using enums for the indexes and nrs of temp8 and temp11.
This make the code much more readable.
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
When the temperature exceed the limit range value,
the driver can handle the interrupt.
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add bit defines for the status register. And add a function
lm90_is_tripped() which will read status register and return
tripped or not, then lm90_alert can call it directly, and in the
future the IRQ thread also can use it.
[JD: Adjusted to include all the new MAX6696 status flags.]
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Bit 2 of status register 2 on MAX6696 (external diode 2 open)
sets ALERT; the bit thus has to be listed in alert_alarms.
Also display a message in the alert handler if the condition
is encountered.
Even though not all overtemperature conditions cause ALERT
to be set, we should not ignore them in the alert handler.
Display messages for all out-of-range conditions.
Reported-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cc: stable@vger.kernel.org
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Use this new function to make code more comprehensible, since we are
reinitialzing the completion, not initializing.
[akpm@linux-foundation.org: linux-next resyncs]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org> (personally at LCE13)
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As well as the usual driver updates and cleanups there's a few
improvements to the core here:
- The start of some improvements to factor out more of the SPI message
loop into the core. Right now this is just simplifying the code a
bit but hopefully next time around we'll also have managed to roll
out some noticable performance improvements which drivers can take
advantage of.
- Support for loading modules for ACPI enumerated SPI devices.
- Managed registration for SPI controllers.
- Helper for another common I/O pattern.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=emSz
-----END PGP SIGNATURE-----
Merge tag 'spi-v3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"As well as the usual driver updates and cleanups there's a few
improvements to the core here:
- The start of some improvements to factor out more of the SPI
message loop into the core. Right now this is just simplifying the
code a bit but hopefully next time around we'll also have managed
to roll out some noticable performance improvements which drivers
can take advantage of.
- Support for loading modules for ACPI enumerated SPI devices.
- Managed registration for SPI controllers.
- Helper for another common I/O pattern"
* tag 'spi-v3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (116 commits)
spi/hspi: add device tree support
spi: atmel: fix return value check in atmel_spi_probe()
spi: spi-imx: only enable the clocks when we start to transfer a message
spi/s3c64xx: Fix doubled clock disable on suspend
spi/s3c64xx: Do not ignore return value of spi_master_resume/suspend
spi: spi-mxs: Use u32 instead of uint32_t
spi: spi-mxs: Don't set clock for each xfer
spi: spi-mxs: Clean up setup_transfer function
spi: spi-mxs: Remove check of spi mode bits
spi: spi-mxs: Fix race in setup method
spi: spi-mxs: Remove bogus setting of ssp clk rate field
spi: spi-mxs: Remove full duplex check, spi core already does it
spi: spi-mxs: Fix chip select control bits in DMA mode
spi: spi-mxs: Fix extra CS pulses and read mode in multi-transfer messages
spi: spi-mxs: Change flag arguments in txrx functions to bit flags
spi: spi-mxs: Always clear INGORE_CRC, to keep CS asserted
spi: spi-mxs: Remove mxs_spi_enable and mxs_spi_disable
spi: spi-mxs: Always set LOCK_CS
spi/s3c64xx: Add missing pm_runtime_put on setup fail
spi/s3c64xx: Add missing pm_runtime_set_active() call in probe()
...
We cap the upper bound of "mtimeout" but since it's signed we should
check for negative values as well. The mistake is harmless. But I have
changed it to unsigned as a cleanup.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
EMC1404 and EMC1424 are similar to EMC1403 and EMC1423,
but support an additional external temperature sensor.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
'of_match_ptr' is defined in linux/of.h. Include it explicitly.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Driver core sets driver data to NULL upon failure or remove.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Kaiwan N Billimoria <kaiwan@designergraphix.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Driver core sets driver data to NULL upon failure or remove.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Marc Pignat <marc.pignat@hevs.ch>
Acked-by: Marc Pignat <marc.pignat@hevs.ch>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
drivers/hwmon/jc42.c:521:1-3: WARNING: PTR_RET can be used
Use PTR_ERR_OR_ZERO rather than if(IS_ERR(...)) + PTR_ERR
Generated by: coccinelle/api/ptr_ret.cocci
CC: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
drivers/hwmon/ltc4261.c:243:1-3: WARNING: PTR_RET can be used
Use PTR_ERR_OR_ZERO rather than if(IS_ERR(...)) + PTR_ERR
Generated by: coccinelle/api/ptr_ret.cocci
CC: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
drivers/hwmon/lm95234.c:704:1-3: WARNING: PTR_RET can be used
Use PTR_ERR_OR_ZERO rather than if(IS_ERR(...)) + PTR_ERR
Generated by: coccinelle/api/ptr_ret.cocci
CC: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
drivers/hwmon/max6697.c:649:1-3: WARNING: PTR_RET can be used
Use PTR_ERR_OR_ZERO rather than if(IS_ERR(...)) + PTR_ERR
Generated by: coccinelle/api/ptr_ret.cocci
CC: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
drivers/hwmon/max6642.c:299:1-3: WARNING: PTR_RET can be used
Use PTR_ERR_OR_ZERO rather than if(IS_ERR(...)) + PTR_ERR
Generated by: coccinelle/api/ptr_ret.cocci
CC: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
drivers/hwmon/ds1621.c:381:1-3: WARNING: PTR_RET can be used
Use PTR_ERR_OR_ZERO rather than if(IS_ERR(...)) + PTR_ERR
Generated by: coccinelle/api/ptr_ret.cocci
CC: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
drivers/hwmon/nct6775.c:3866:1-3: WARNING: PTR_RET can be used
Use PTR_ERR_OR_ZERO rather than if(IS_ERR(...)) + PTR_ERR
Generated by: coccinelle/api/ptr_ret.cocci
CC: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Also introduce dev variable in probe function to simplify access
to client->dev, and use new macro ATTRIBUTE_GROUPS to declare
attribute groups.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Modify code to use is_visible to determine if an attribute should be created
or not, then use devm_hwmon_device_register_with_groups to create the hwmon
device and all attributes in one operation.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Also introduce new variable dev pointing to client->dev in the probe
function, and use new macro ATTRIBUTE_GROUPS to declare attribute groups.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Also rename new_client variable to client and introduce
new variable dev pointing to client->dev in the probe function,
and use new macro ATTRIBUTE_GROUPS to declare attribute groups.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Drivers using the new hwmon_device_register_with_groups API often have a
remove function which consists solely of a call hwmon_device_unregister().
Provide support for devm_hwmon_device_register_with_groups and
devm_hwmon_device_unregister to allow this repeated code to be removed
and help eliminate error handling code.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
