We need the USB fixes in here, and it resolves a merge conflict in:
drivers/usb/dwc3/dwc3-pci.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The kerneldoc for usb_get_dev() and usb_get_intf() says that drivers
should always refcount the references they hold for the usb_device or
usb_interface structure, respectively. But this is an overstatement:
In many cases drivers do not access these references after they have
been unbound, and in such cases refcounting is unnecessary.
This patch updates the kerneldoc for the two routines, explaining when
a driver does not need to increment and decrement the refcount. This
should help dispel misconceptions which might otherwise afflict
programmers new to the USB subsystem.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/Yhjp4Rp9Alipmwtq@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's a revert of a commit which erroneously added a device id used for
the EPP/MEM mode of ch341 devices.
Included are also some new modem device ids.
All have been in linux-next with no reported issues.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCYhd+0wAKCRALxc3C7H1l
CBXUAQCOwSNZ03h+1cfWCbAbAWX8WYmAv+TsiXSEidMAdzAZyQEA4iaz8VumdoqO
hwK2Y1RKjqZ6/Kw8UNQ9/eTjq0tQmwc=
=ysqp
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-5.17-rc6' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for 5.17-rc6
Here's a revert of a commit which erroneously added a device id used for
the EPP/MEM mode of ch341 devices.
Included are also some new modem device ids.
All have been in linux-next with no reported issues.
* tag 'usb-serial-5.17-rc6' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: option: add Telit LE910R1 compositions
USB: serial: option: add support for DW5829e
Revert "USB: serial: ch341: add new Product ID for CH341A"
The Qualcomm Embedded USB Debugger is not a pluggable USB device, and
can only be present on Qualcomm SoCs. Hence add a dependency on
ARCH_QCOM, to prevent asking the user about this driver when configuring
a kernel without Qualcomm SoC support.
Fixes: 9a1bf58ccd ("usb: misc: eud: Add driver support for Embedded USB Debugger(EUD)")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/f3ba3ea0d7f5e628c71cb7a9d62c9fb4589297b1.1645630266.git.geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This has been allocated just a few lines earlier with a
zalloc(). The value is known and "|=" is a waste of memory
cycles.
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20220217133549.27961-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At the end of qtd_fill(), we assign the 'int count' variable to the 'size_t
length' field of 'struct ehci_qtd' -- which implies a problematic type cast.
Let's make that variable and the function's result *unsigned int* instead...
Found by Linux Verification Center (linuxtesting.org) with the SVACE static
analysis tool.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/8c64fdeb-5857-8cb3-cfd8-0c248a14b909@omp.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The interrupt service routine registered for the gadget is a primary
handler which mask the interrupt source and a threaded handler which
handles the source of the interrupt. Since the threaded handler is
voluntary threaded, the IRQ-core does not disable bottom halves before
invoke the handler like it does for the forced-threaded handler.
Due to changes in networking it became visible that a network gadget's
completions handler may schedule a softirq which remains unprocessed.
The gadget's completion handler is usually invoked either in hard-IRQ or
soft-IRQ context. In this context it is enough to just raise the softirq
because the softirq itself will be handled once that context is left.
In the case of the voluntary threaded handler, there is nothing that
will process pending softirqs. Which means it remain queued until
another random interrupt (on this CPU) fires and handles it on its exit
path or another thread locks and unlocks a lock with the bh suffix.
Worst case is that the CPU goes idle and the NOHZ complains about
unhandled softirqs.
Disable bottom halves before acquiring the lock (and disabling
interrupts) and enable them after dropping the lock. This ensures that
any pending softirqs will handled right away.
Link: https://lkml.kernel.org/r/c2a64979-73d1-2c22-e048-c275c9f81558@samsung.com
Fixes: e5f68b4a3e ("Revert "usb: dwc3: gadget: remove unnecessary _irqsave()"")
Cc: stable <stable@kernel.org>
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://lore.kernel.org/r/Yg/YPejVQH3KkRVd@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Assure that host may not manipulate the index to point
past endpoint array.
Signed-off-by: Szymon Heidrich <szymon.heidrich@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order for the phy driver to be able to actually get and control
the cs and reset GPIOs the dev_id member of the gpiod_lookup table must
be set to point to the dev_name() of the ulpi-device instantiated by
dwc3_ulpi_init().
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220213130524.18748-6-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some Android x86 tablets with a Bay Trail (BYT) SoC and a Crystal Cove
PMIC, which does not support charger-detection, rely on the TUSB1211 phy
for charger-detection.
Windows tablets with the same SoC + PMIC often use an extra chip for
charger-detection like the FSA831A. But since on Android tablets
the designers already need to add a TUSB1211 phy to support device/gadget
mode the phy is used to do charger-detection instead.
These Android x86 tablets can be identified by the unique combination of
a Bay Trail SoC (already checked for by PCI-ids) + a Crystal Cove PMIC +
not using the standard ACPI battery and ac drivers. Where as on Windows
tablets the standard ACPI battery and ac drivers will be used on BYT
boards with a Crystal Cove PMIC.
Set a special kernel-internal (so not part of the dt-bindings)
"linux,phy_charger_detect" property on these boards, which tells the
tusb1210 driver to enable charger-detection.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220213130524.18748-5-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The quirk handling may need to set some different properties
which means using a different swnode, move the setting of the swnode
to inside dwc3_pci_quirks() so that the quirk handling can choose
a different swnode.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220213130524.18748-4-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
WUSB3801 features a configurable port type, accessory detection, and
plug orientation detection. It provides a hardware "ID" pin output for
compatibility with USB 2.0 OTG PHYs. Add a typec class driver for it.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/r/20220214050118.61015-5-samuel@sholland.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Basic programmable non-PD Type-C port controllers do not need the full
TCPM library, but they share the same devicetree binding and the same
typec_capability structure. Factor out a helper for parsing those
properties which map to fields in struct typec_capability, so the code
can be shared between TCPM and basic non-TCPM drivers.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/r/20220214050118.61015-4-samuel@sholland.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In xhci_endpoint_{disable|reset}() the expression '&vdev->eps[ep_index]'
just cannot be NULL, so the checks have no sense at all...
Found by Linux Verification Center (linuxtesting.org) with the SVACE static
analysis tool.
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220216095153.1303105-9-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Trying to disable Link Powermanagement (LPM) before port reset is
unnecessary and can cause additional delay if host can't communicate
with the device, which is often the reason why device is reset in the
first place.
usb_disable_lpm() will
- zero usb U1/U2 timeouts for the hub downstream port
- send ENABLE U1/U2 clear feature requests to the connected device.
- increase internal reference count for udev->lpm_disable_count
There is no need to zero U1/U2 hub port timeouts, or clearing the
U1/U2 enable for the connected device before reset. These are set
to default by the reset.
USB 3.1 section 10.2.2 "HUB Downstream port U1/U2 timers" states that:
"the U1 and U2 timeout values for a downstream port reset to the default
values when the port receives a SetPortFeature request for a port reset"
Set the udev->lpm_disable_count to "1" after port reset, which is the
default lpm_disable_count value when allocating udev, representing
disabled LPM.
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220216095153.1303105-8-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Every lpm commmand, both for USB 2 and USB 3 devies used the same
xhci->lpm_command structure to change max exit latency.
xhci->lpm_command is only protected by a hcd->bandwidth mutex, which is
not enoungh as USB 2 and USB 3 devices are behind separate HCDs.
Simplify code and avoid unnecessary locking risks by allocating
separate command structures for each lpm command, just like with
all other commands.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220216095153.1303105-7-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To support systems with several xhci controllers with active
dbc on each xhci we need to use IDR to identify and give
an index to each port.
Avoid using global struct tty_driver.driver_state for storing
dbc port pointer as it won't work with several dbc ports
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220216095153.1303105-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current workaround to call the dbc_tty_init() in probe is
not working in case we have several xhci devices with dbc enabled.
dbc_tty_init() should be called only once by a module init call when
module is loaded.
until dbgtty is its own module call dbc_tty_init() from xhci
module init call.
Same is true for unloading and dbc_tty_exit()
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220216095153.1303105-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These names give the impression the functions are related to
module init calls, but are in fact creating and removing the dbc
fake device
Rename them to xhci_create_dbc_dev() and xhci_remove_dbc_dev().
We will need the _init and _exit names for actual dbc module init
and exit calls.
No functional changes
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220216095153.1303105-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Turn the dbgtty closer to a device driver by allocating the dbc
structure in its own xhci_dbc_tty_probe() function, and freeing it
in xhci_dbc_tty_remove()
Remove xhci_do_dbc_exit() as its no longer needed.
allocate and create the dbc strcuture in xhci_dbc_tty_probe()
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220216095153.1303105-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Refactor xhci_dbc_init(), splitting it into logical
parts closer to the Linux device model.
- Create the fake dbc device, depends on xhci strucure
- Allocate a dbc structure, xhci agnostic
- Call xhci_dbc_tty_probe(), similar to actual probe.
Adjustments to xhci_dbc_exit and xhci_dbc_remove are also needed
as a result to the xhci_dbc_init() changes
Mostly non-functional changes, except for creating the dbc sysfs
entry earlier, together with the dbc structure.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220216095153.1303105-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The CONFIG_OF maybe set, but it may not be applicable to a device. In
such case, checking against that can cause the device fail to
initialize. Check against the device node (device->of_node) instead.
Fixes: a102f07e4e ("usb: dwc3: drd: Add support for usb-conn-gpio based usb-role-switch")
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/9f15580ad5810b1e5f31c241b35ebedfbfc30a3f.1644964864.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the custom functions xhci_mtk_ldos_{enable,disable}() by
switching to using regulator_bulk to perform the very same thing,
as the regulators are always either both enabled or both disabled.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220214111905.77903-1-angelogioacchino.delregno@collabora.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the gadget driver hasn't been (yet) configured, and the cable is
connected to a HOST, the SFTDISCON gets cleared unconditionally, so the
HOST tries to enumerate it.
At the host side, this can result in a stuck USB port or worse. When
getting lucky, some dmesg can be observed at the host side:
new high-speed USB device number ...
device descriptor read/64, error -110
Fix it in drd, by checking the enabled flag before calling
dwc2_hsotg_core_connect(). It will be called later, once configured,
by the normal flow:
- udc_bind_to_driver
- usb_gadget_connect
- dwc2_hsotg_pullup
- dwc2_hsotg_core_connect
Fixes: 17f934024e ("usb: dwc2: override PHY input signals with usb role switch support")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://lore.kernel.org/r/1644999135-13478-1-git-send-email-fabrice.gasnier@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the Bay Trail phy GPIO mappings where added cs and reset were swapped,
this did not cause any issues sofar, because sofar they were always driven
high/low at the same time.
Note the new mapping has been verified both in /sys/kernel/debug/gpio
output on Android factory images on multiple devices, as well as in
the schematics for some devices.
Fixes: 5741022cbd ("usb: dwc3: pci: Add GPIO lookup table on platforms without ACPI GPIO resources")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220213130524.18748-3-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The interrupt mask is enabled before any potential failure points in
the driver, which can leave a failure path where we exit with
interrupts enabled but the device not live. This causes an infinite
stream of interrupts on an Apple M1 Pro laptop on USB-C.
Add a failure label that's used post enabling interrupts, where we
mask them again before returning an error.
Suggested-by: Sven Peter <sven@svenpeter.dev>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Link: https://lore.kernel.org/r/e6b80669-20f3-06e7-9ed5-8951a9c6db6f@kernel.dk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The -ENODEV return value from xhci_check_args() is incorrectly changed
to -EINVAL in a couple places before propagated further.
xhci_check_args() returns 4 types of value, -ENODEV, -EINVAL, 1 and 0.
xhci_urb_enqueue and xhci_check_streams_endpoint return -EINVAL if
the return value of xhci_check_args <= 0.
This causes problems for example r8152_submit_rx, calling usb_submit_urb
in drivers/net/usb/r8152.c.
r8152_submit_rx will never get -ENODEV after submiting an urb when xHC
is halted because xhci_urb_enqueue returns -EINVAL in the very beginning.
[commit message and header edit -Mathias]
Fixes: 203a86613f ("xhci: Avoid NULL pointer deref when host dies.")
Cc: stable@vger.kernel.org
Signed-off-by: Hongyu Xie <xiehongyu1@kylinos.cn>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220215123320.1253947-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When HCE(Host Controller Error) is set, it means an internal
error condition has been detected. Software needs to re-initialize
the HC, so add this check in xhci resume.
Cc: stable@vger.kernel.org
Signed-off-by: Puma Hsu <pumahsu@google.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220215123320.1253947-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit e0082698b6 ("usb: dwc3: ulpi: conditionally resume ULPI PHY")
fixed an issue where ULPI transfers would timeout if any requests where
send to the phy sometime after init, giving it enough time to auto-suspend.
Commit e5f4ca3fce ("usb: dwc3: ulpi: Fix USB2.0 HS/FS/LS PHY suspend
regression") changed the behavior to instead of clearing the
DWC3_GUSB2PHYCFG_SUSPHY bit, add an extra sleep when it is set.
But on Bay Trail devices, when phy_set_mode() gets called during init,
this leads to errors like these:
[ 28.451522] tusb1210 dwc3.ulpi: error -110 writing val 0x01 to reg 0x0a
[ 28.464089] tusb1210 dwc3.ulpi: error -110 writing val 0x01 to reg 0x0a
Add "snps,dis_u2_susphy_quirk" to the settings for Bay Trail devices to
fix this. This restores the old behavior for Bay Trail devices, since
previously the DWC3_GUSB2PHYCFG_SUSPHY bit would get cleared on the first
ulpi_read/_write() and then was never set again.
Fixes: e5f4ca3fce ("usb: dwc3: ulpi: Fix USB2.0 HS/FS/LS PHY suspend regression")
Cc: stable@kernel.org
Cc: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220213130524.18748-2-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The original workaround was added prior to commit e4788edc73 ("USB:
EHCI: Add alias for Broadcom INSNREG"). Now that brcm_insnreg exists in
struct ehci_regs we can use that instead of having a local definition.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20220215000813.1779032-1-chris.packham@alliedtelesis.co.nz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 'ret' local variables are often initialized to 0 but this value is
unused, thus we can kill those initializers...
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/901b7478-45b6-d8b3-f5c6-555712485232@omp.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace "struct list_head head = LIST_HEAD_INIT(head)" with
"LIST_HEAD(head)" to simplify the code.
LIST_HEAD() helps to clean up the code "struct list_head vudc_devices =",
only to care about the variable 'vudc_devices'.
Reviewed-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Cai Huoqing <cai.huoqing@linux.dev>
Link: https://lore.kernel.org/r/20220211012807.7415-1-cai.huoqing@linux.dev
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds a debugfs file for ULPI devices which contains a dump of their
registers. This is useful for debugging basic connectivity problems. The
file is created in ulpi_register because many devices will never have a
driver bound (as they are managed in hardware by the USB controller
device).
The root directory of this subsystem is created before we register the
bus to ensure that devices can always create their directories.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20220127190004.1446909-4-sean.anderson@seco.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmIJZmoeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGZdoH/04d8zUhM3Fd3ACB
V/ONtOXmkfP2mEJSjb7cXTN1EM2SlOBdSnSsEw09FtGhjHABjOnLho4J5ixk9TH8
zNMNI3EMksM2T9KadHwxv8Vvp1LTrWRzMbws8tOCPA0RkOpikJfClC8CzRAyidJ3
cAbbDH/Jl1GnVZ8bpKmv2auYt+kNVGb0cwJ2W8phCwwkL7sLky5tgYeaGiJEXbJf
Tfi/3qtFdmYjD8wtYnCfzjnB7suG5nF7rGEnxCIxNi+IA4DieUv2c1KchuoaBfT9
df364VjKaGT3j+GB07ksQ/8mkwWiRXsCzOXAyMZSZaWjdMD4aAhCTJak5j7/TvGC
wtgHPww=
=/CMW
-----END PGP SIGNATURE-----
Merge 5.17-rc4 into usb-next
We need the USB fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are some new device ids for 5.17-rc4.
All have been in linux-next with no reported issues.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCYgZ+2gAKCRALxc3C7H1l
CDoSAP9qPhQUn/i4I6ggD4oB25VaGWHxZVaoQYj/R74OjvWxDwEA0+5fIbS9T8qr
rU70IRzH4KDdW3OFPCgr58+MIotAtwc=
=1R+F
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-5.17-rc4' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for 5.17-rc4
Here are some new device ids for 5.17-rc4.
All have been in linux-next with no reported issues.
* tag 'usb-serial-5.17-rc4' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: cp210x: add CPI Bulk Coin Recycler id
USB: serial: cp210x: add NCR Retail IO box id
USB: serial: ftdi_sio: add support for Brainboxes US-159/235/320
USB: serial: option: add ZTE MF286D modem
USB: serial: ch341: add support for GW Instek USB2.0-Serial devices
Add support for control peripheral of EUD (Embedded USB Debugger) to
listen to events such as USB attach/detach, pet EUD to indicate software
is functional.Reusing the platform device kobj, sysfs entry 'enable' is
created to enable or disable EUD.
To enable the eud the following needs to be done
echo 1 > /sys/bus/platform/.../enable
To disable eud, following is the command
echo 0 > /sys/bus/platform/.../enable
Signed-off-by: Souradeep Chowdhury <quic_schowdhu@quicinc.com>
Link: https://lore.kernel.org/r/0ac5c2b2c8e4ce4f4f342a08b48cfc61aeaf7ee8.1644339918.git.quic_schowdhu@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Richtek RT1719 is a sink-only Type-C PD controller it complies with
latest USB Type-C and PD standards. It integrates the physical layer of
USB power delivery protocol to allow up to 100W of power.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: ChiYuan Huang <cy_huang@richtek.com>
Link: https://lore.kernel.org/r/1644421362-32104-3-git-send-email-u0084500@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support ip-sleep wakeup for mt8195, it's a specific revision for
each USB controller, and not following IPM rule.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20220128062902.26273-2-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The DWC2 IP on the Agilex platform does not support clock-gating.
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Link: https://lore.kernel.org/r/20220125161821.1951906-2-dinguyen@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While the existing code code imposes a limit on the used memory, it might be
over pessimistic (even if this is unlikely).
Example scenario:
8 threads running in parallel, all entering
"usbfs_increase_memory_usage()" at the same time.
The atomic accesses in "usbfs_increase_memory_usage()" could be
serialized like this:
8 x "atomic64_add"
8 x "atomic64_read"
If the 8 x "atomic64_add" raise "usbfs_memory_usage" above the limit,
then all 8 calls of "usbfs_increase_memory_usage()" will return with
-ENOMEM. If you instead serialize over the whole access to
"usbfs_memory_usage" by using a spinlock, some of these calls will
succeed.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Ingo Rohloff <ingo.rohloff@lauterbach.com>
Link: https://lore.kernel.org/r/20220209123303.103340-2-ingo.rohloff@lauterbach.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the gadget driver hasn't been (yet) configured, and the cable is
connected to a HOST, the SFTDISCON gets cleared unconditionally, so the
HOST tries to enumerate it.
At the host side, this can result in a stuck USB port or worse. When
getting lucky, some dmesg can be observed at the host side:
new high-speed USB device number ...
device descriptor read/64, error -110
Fix it in drd, by checking the enabled flag before calling
dwc2_hsotg_core_connect(). It will be called later, once configured,
by the normal flow:
- udc_bind_to_driver
- usb_gadget_connect
- dwc2_hsotg_pullup
- dwc2_hsotg_core_connect
Fixes: 17f934024e ("usb: dwc2: override PHY input signals with usb role switch support")
Cc: stable@kernel.org
Reviewed-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://lore.kernel.org/r/1644423353-17859-1-git-send-email-fabrice.gasnier@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Check the size of the RNDIS_MSG_SET command given to us before
attempting to respond to an invalid message size.
Reported-by: Szymon Heidrich <szymon.heidrich@gmail.com>
Cc: stable@kernel.org
Tested-by: Szymon Heidrich <szymon.heidrich@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stall the control endpoint in case provided index exceeds array size of
MAX_CONFIG_INTERFACES or when the retrieved function pointer is null.
Signed-off-by: Szymon Heidrich <szymon.heidrich@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
