The default for "verbose" is 0. Update description to match.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
pci_setup_device() has saved the PCI revision in the pci_dev
struct since Linux 2.6.23. Use it.
Cc: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Brazil uses 6MHz-spaced channels. So, the nyquist filter for
DVB-C should be different, otherwise, inter-channel interference
may badly affect the device, and signal may not be properly decoded.
On my tests here, without this patch, sometimes channels are seen,
but, most of the time, PID filter returns with timeout.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix issue where firmware does not release on cold reset.
Also, default firmware never cold resets in multi tuner
environment.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
[media] ngene: Fix CI data transfer regression Fix CI data transfer regression introduced by previous cleanup.
[media] v4l: make sure drivers supply a zeroed struct v4l2_subdev
[media] Missing frontend config for LME DM04/QQBOX
[media] rc_core: avoid kernel oops when rmmod saa7134
[media] imon: add conditional locking in change_protocol
[media] rc: show RC_TYPE_OTHER in sysfs
[media] ite-cir: modular build on ppc requires delay.h include
[media] mceusb: add Dell transceiver ID
A recent patch has given individual soc-camera host drivers a possibility
to calculate .sizeimage and .bytesperline pixel format fields internally,
however, some drivers relied on the core calculating these values for
them, following a default algorithm. This patch restores the default
calculation for such drivers.
Based on initial patch by Guennadi Liakhovetski, found here:
http://www.spinics.net/lists/linux-media/msg31282.html
Except that this covers try_fmt aswell.
Signed-off-by: Sergio Aguirre <saaguirre@ti.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The v4l2_subdev_* functions are meant for older V4L2 drivers that do not use
the control framework yet. These functions should not be used by subdev_do_ioctl.
Most of those backwards compatibility functions are just stubs, but commit
87a0c94ce6 actually changed the behavior of
v4l2_subdev_queryctrl, so calling that one from subdev_do_ioctl broke the
control enumeration in subdev nodes.
The fix is simply not to use those compatibility functions in v4l2-subdev.c.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In the IR interrupt handler of cx88-input.c there's a 32-bit multiply
overflow which causes IR pulse durations to be incorrectly calculated.
This is a regression caused by commit 2997137be8.
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If v4l2_device_register_subdev() fails, the reference to the subdev
module taken by the function isn't released. Fix this.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: stable@kernel.org
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix CI data transfer regression introduced by previous cleanup.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some v4l drivers currently don't initialize their struct v4l2_subdev
with zeros, and this is a problem since some of the v4l2 code expects
this. One example is the addition of internal_ops in commit 45f6f84,
after that we are at risk of random oopses with these drivers when code
in v4l2_device_register_subdev tries to dereference sd->internal_ops->*,
as can be shown by the report at http://bugs.launchpad.net/bugs/745213
and analysis of its crash at https://lkml.org/lkml/2011/4/1/168
Use kzalloc within problematic drivers to ensure we have a zeroed struct
v4l2_subdev.
BugLink: http://bugs.launchpad.net/bugs/745213
Cc: <stable@kernel.org>
Signed-off-by: Herton Ronaldo Krzesinski <herton.krzesinski@canonical.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The following is a patch to avoid a kernel oops when running rmmod
saa7134 on kernel 2.6.27.1. The change is as suggested by mchehab on
irc.freenode.org
Signed-off-by: Hussam Al-Tayeb <ht990332@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The imon_ir_change_protocol function gets called two different ways, one
way is from rc_register_device, for initial protocol selection/setup,
and the other is via a userspace-initiated protocol change request,
either by direct sysfs prodding or by something like ir-keytable.
In the rc_register_device case, the imon context lock is already held,
but when initiated from userspace, it is not, so we must acquire it,
prior to calling send_packet, which requires that the lock is held.
Without this change, there's an easily reproduceable deadlock when
another function calls send_packet (such as either of the display write
fops) after a userspace-initiated change_protocol.
With a lock-debugging-enabled kernel, I was getting this:
[ 15.014153] =====================================
[ 15.015048] [ BUG: bad unlock balance detected! ]
[ 15.015048] -------------------------------------
[ 15.015048] ir-keytable/773 is trying to release lock (&ictx->lock) at:
[ 15.015048] [<ffffffff814c6297>] mutex_unlock+0xe/0x10
[ 15.015048] but there are no more locks to release!
[ 15.015048]
[ 15.015048] other info that might help us debug this:
[ 15.015048] 2 locks held by ir-keytable/773:
[ 15.015048] #0: (&buffer->mutex){+.+.+.}, at: [<ffffffff8119d400>] sysfs_write_file+0x3c/0x144
[ 15.015048] #1: (s_active#87){.+.+.+}, at: [<ffffffff8119d4ab>] sysfs_write_file+0xe7/0x144
[ 15.015048]
[ 15.015048] stack backtrace:
[ 15.015048] Pid: 773, comm: ir-keytable Not tainted 2.6.38.4-20.fc15.x86_64.debug #1
[ 15.015048] Call Trace:
[ 15.015048] [<ffffffff81089715>] ? print_unlock_inbalance_bug+0xca/0xd5
[ 15.015048] [<ffffffff8108b35c>] ? lock_release_non_nested+0xc1/0x263
[ 15.015048] [<ffffffff814c6297>] ? mutex_unlock+0xe/0x10
[ 15.015048] [<ffffffff814c6297>] ? mutex_unlock+0xe/0x10
[ 15.015048] [<ffffffff8108b67b>] ? lock_release+0x17d/0x1a4
[ 15.015048] [<ffffffff814c6229>] ? __mutex_unlock_slowpath+0xc5/0x125
[ 15.015048] [<ffffffff814c6297>] ? mutex_unlock+0xe/0x10
[ 15.015048] [<ffffffffa02964b6>] ? send_packet+0x1c9/0x264 [imon]
[ 15.015048] [<ffffffff8108b376>] ? lock_release_non_nested+0xdb/0x263
[ 15.015048] [<ffffffffa0296731>] ? imon_ir_change_protocol+0x126/0x15e [imon]
[ 15.015048] [<ffffffffa024a334>] ? store_protocols+0x1c3/0x286 [rc_core]
[ 15.015048] [<ffffffff81326e4e>] ? dev_attr_store+0x20/0x22
[ 15.015048] [<ffffffff8119d4cc>] ? sysfs_write_file+0x108/0x144
...
The original report that led to the investigation was the following:
[ 1679.457305] INFO: task LCDd:8460 blocked for more than 120 seconds.
[ 1679.457307] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 1679.457309] LCDd D ffff88010fcd89c8 0 8460 1 0x00000000
[ 1679.457312] ffff8800d5a03b48 0000000000000082 0000000000000000 ffff8800d5a03fd8
[ 1679.457314] 00000000012dcd30 fffffffffffffffd ffff8800d5a03fd8 ffff88010fcd86f0
[ 1679.457316] ffff8800d5a03fd8 ffff8800d5a03fd8 ffff88010fcd89d0 ffff8800d5a03fd8
[ 1679.457319] Call Trace:
[ 1679.457324] [<ffffffff810ff1a5>] ? zone_statistics+0x75/0x90
[ 1679.457327] [<ffffffff810ea907>] ? get_page_from_freelist+0x3c7/0x820
[ 1679.457330] [<ffffffff813b0a49>] __mutex_lock_slowpath+0x139/0x320
[ 1679.457335] [<ffffffff813b0c41>] mutex_lock+0x11/0x30
[ 1679.457338] [<ffffffffa0d54216>] display_open+0x66/0x130 [imon]
[ 1679.457345] [<ffffffffa01d06c0>] usb_open+0x180/0x310 [usbcore]
[ 1679.457349] [<ffffffff81143b3b>] chrdev_open+0x1bb/0x2d0
[ 1679.457350] [<ffffffff8113d93d>] __dentry_open+0x10d/0x370
[ 1679.457352] [<ffffffff81143980>] ? chrdev_open+0x0/0x2d0
...
Bump the driver version here so its easier to tell if people have this
locking fix or not, and also make locking during probe easier to follow.
CC: stable@kernel.org
Reported-by: Benjamin Hodgetts <ben@xnode.org>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (42 commits)
[media] media: vb2: correct queue initialization order
[media] media: vb2: fix incorrect v4l2_buffer->flags handling
[media] s5p-fimc: Add support for the buffer timestamps and sequence
[media] s5p-fimc: Fix bytesperline and plane payload setup
[media] s5p-fimc: Do not allow changing format after REQBUFS
[media] s5p-fimc: Fix FIMC3 pixel limits on Exynos4
[media] tda18271: update tda18271c2_rf_cal as per NXP's rev.04 datasheet
[media] tda18271: update tda18271_rf_band as per NXP's rev.04 datasheet
[media] tda18271: fix bad calculation of main post divider byte
[media] tda18271: prog_cal and prog_tab variables should be s32, not u8
[media] tda18271: fix calculation bug in tda18271_rf_tracking_filters_init
[media] omap3isp: queue: Don't corrupt buf->npages when get_user_pages() fails
[media] v4l: Don't register media entities for subdev device nodes
[media] omap3isp: Don't increment node entity use count when poweron fails
[media] omap3isp: lane shifter support
[media] omap3isp: ccdc: support Y10/12, 8-bit bayer fmts
[media] media: add missing 8-bit bayer formats and Y12
[media] v4l: add V4L2_PIX_FMT_Y12 format
cx23885: Fix stv0367 Kconfig dependency
[media] omap3isp: Use isp xclk defines
...
Fix up trivial conflict (spelink errurs) in drivers/media/video/omap3isp/isp.c
q->memory entry is initialized to late, so if allocation of memory buffers
fails, the buffers might not be freed correctly (q->memory is tested in
__vb2_free_mem, which can be called before setting q->memory).
Reported-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Pawel Osciak <pawel@osciak.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Videobuf2 core assumes that driver doesn't set any buffer flags.
This is correct for buffer state flags that videobuf2 manages,
but the other flags like V4L2_BUF_FLAG_{KEY,P,B}FRAME,
V4L2_BUF_FLAG_TIMECODE and V4L2_BUF_FLAG_INPUT should be passed from or to
the driver.
Reported-by: Jonghun Han <jonghun.han@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Pawel Osciak <pawel@osciak.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for buffer timestamps and the sequence number in
the video capture driver.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make sure the sizeimage for 3-planar color formats is
width * height * 3/2 and the bytesperline is same for each
plane in case of a multi-planar format.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Protecting the color format with vb2_is_streaming() is not sufficient
as this prevents changing the format only after VIDIOC_STREAMON.
To prevent the color format reconfiguration as soon as buffers
are allocated use vb2_is_busy() instead.
Also make the videobuf queue ops structure static.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Correct pixel limits for the fourth FIMC entity on Exynos4 SoCs.
FIMC3 only supports the writeback input from the LCD mixer.
Also rename s5pv310 variant to exynos4 which is needed after
renaming s5pv310 series to Exynos4.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This reverts commit 35d9f510b6.
Quoth Jiri Slaby:
"It fixes mmap when IOMMU is used on x86 only, but breaks architectures
like ARM or PPC where virt_to_phys(dma_alloc_coherent) doesn't work.
We need there dma_mmap_coherent or similar (the trickery what
snd_pcm_default_mmap does but in some saner way). But this cannot be
done at this phase."
Requested-by: Jiri Slaby <jslaby@suse.cz>
Cc: Russell King - ARM Linux <linux@arm.linux.org.uk>
Cc: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
R_MPD bit 3 does not depend on analog vs. digital. Just use
(0x7f & pd) directly from the values in the main pll table.
Thanks to Stefan Sibiga for pointing this out.
Cc: Stefan Sibiga <stefansibiga@yahoo.ca>
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix type of prog_cal and prog_tab variables to avoid any possible
calculation errors.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Misplaced parenthesis cause a calculation bug in
tda18271_rf_tracking_filters_init
Thanks to Stefan Sibiga for pointing this out.
Cc: Stefan Sibiga <stefansibiga@yahoo.ca>
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
get_user_pages() can return a negative error code when it fails. Set
buf->npages to 0 in that case, to prevent isp_video_buffer_cleanup()
from releasing invalid pages.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Subdevs already have their own entity, don't register as second one when
registering the subdev device node.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@maxwell.research.nokia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When open a device node, all entities part of the same pipeline are
powered on. If one of the entities fails to be powered on, the open
operations fails. In that case the device node entity use count must not
be incremented.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
To use the lane shifter, set different pixel formats at each end of
the link at the CCDC input.
Signed-off-by: Michael Jones <michael.jones@matrix-vision.de>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for 8-bit bayer and 10- and 12-bit grey formats at the CCDC
input. Y12 is truncated to Y10 at the CCDC output.
Signed-off-by: Michael Jones <michael.jones@matrix-vision.de>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When a failure to stop a module in the pipeline is detected, the only
way to recover is to reset the ISP. However, as other users can be using
a different pipeline with other modules, the ISP can't be reset
synchronously with the error detection.
Mark the ISP as needing a reset when a failure to stop a pipeline is
detected, and reset the ISP when the last user releases the last
reference to the ISP.
Modify the omap3isp_pipeline_set_stream() function to record the new ISP
pipeline state only when no error occurs, except when stopping the
pipeline in which case the pipeline is still marked as stopped.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
struct ispstat_generic_config's comments refers to isph3a_aewb_config,
isph3a_af_config and isphist_config. But those structs have had their
names prefixed with 'omap3'. So, let's update the comments.
Signed-off-by: David Cohen <david.cohen@nokia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The link flags were not properly handled in __media_entity_setup_link
which could lead to link_notify callback to be called when the flags are
not modified. Fix this.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It doesn't get more trivial than these.
Signed-off-by: Michael Jones <michael.jones@matrix-vision.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Round properly the rsz factor so that we get highest rsz so that the input
width (or height) is highest possible smaller or equal to what the user
asks.
Signed-off-by: Sakari Ailus <sakari.ailus@maxwell.research.nokia.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As the number of phases/taps, used to select the correct equations to
compute the ratio, depends on the ratio, start with the 7-tap mode
equations to compute an approximation of the ratio, and switch to the
4-tap mode equations if the approximation is lower than or equal to 512.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When the crop rectangle needs to be modified to match hardware
requirements, center the resulting rectangle on the requested rectangle
instead of removing pixels from the right and bottom sides only.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since commit
379fa5d ([media] V4L: mx3_camera: convert to videobuf2)
mx3_camera uses videobuf2, but that commit didn't upgrade the select
resulting in the following build failure:
drivers/built-in.o: In function `mx3_camera_init_videobuf':
clkdev.c:(.text+0x86580): undefined reference to `vb2_dma_contig_memops'
drivers/built-in.o: In function `mx3_camera_probe':
clkdev.c:(.devinit.text+0x3548): undefined reference to `vb2_dma_contig_init_ctx'
clkdev.c:(.devinit.text+0x3578): undefined reference to `vb2_dma_contig_cleanup_ctx'
drivers/built-in.o: In function `mx3_camera_remove':
clkdev.c:(.devexit.text+0x674): undefined reference to `vb2_dma_contig_cleanup_ctx'
make[2]: *** [.tmp_vmlinux1] Error 1
make[1]: *** [sub-make] Error 2
make: *** [all] Error 2
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If the camera host driver (sh_mobile_ceu_camera.c) is unloaded and then
reloaded, probe will fail, because camera client .set_bus_param() and
.query_bus_param() methods have been set to NULL. Fix this by caching
the original pointers and restoring them on driver-unbind.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
i2c_unregister_device() frees the I2C client, so, dereferencing it
afterwards is a bug, that leads to Oopses.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With the introduction of CSI2 support on sh-mobile, the host driver
switched to using v4l2_device_call_until_err() with grp_id == 0 to
call subdev operations on the sensor and the CSI2 subdev. However,
this has broken multi-client set ups like the one on migor, because
that way all operations get called on both clients. To fix this add
a grp_id and set it to the client private context.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
buf->size is not yet initialised in videobuf2-dma-contig at the time of
the error message, use "size."
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The videobuf2-dma-contig allocator returns an ERR_PTR() on failure, not
a NULL like all other allocators. Fix videobuf2-core to also correctly
recognise those failures.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If allocating stream buffers for one of the primary streams (e.g. YUV)
failed during card probe, the error path clean up would try to manipulate
the yet unitialized IDX stream structures. This caused a BUG due to
unitialized list heads.
Detect that case and ignore the uninitialized IDX stream.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Device is based on STV0903 demod and STV6110x tuner
Signed-off-by: Oleg Roitburd <oroitburd@gmail.com>
Signed-off-by: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Seems like 'adap->fe' test for NULL was meant to be before we dereference
that pointer.
Signed-off-by: Mariusz Kozlowski <mk@lab.zgora.pl>
Signed-off-by: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch fixes the warning about bad names for sys-fs and other kernel-things. The flexcop-pci driver was using '/'-characters in it, which is not good.
This has been fixed in several attempts by several people, but obviously never made it into the kernel.
Signed-off-by: Patrick Boettcher <pboettcher@kernellabs.com>
Cc: Steffen Barszus <steffenbpunkt@googlemail.com>
Cc: Boris Cuber <me@boris64.net>
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix typo introduced in b4d6046e84.
Spotted by Dr. David Alan Gilbert. Thanks for that.
Signed-off-by: Patrick Boettcher <pboettcher@kernellabs.com>
Cc: Dr. David Alan Gilbert <linux@treblig.org>
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, UV: Fix kdump reboot
x86, amd-nb: Rename CPU PCI id define for F4
sound: Add delay.h to sound/soc/codecs/sn95031.c
x86, mtrr, pat: Fix one cpu getting out of sync during resume
x86, microcode: Unregister syscore_ops after microcode unloaded
x86: Stop including <linux/delay.h> in two asm header files
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
[media] radio: wl128x: Update registration process with ST
[media] staging: altera-jtag needs delay.h
As underlying ST driver registration API's have changed with
latest 2.6.38-rc8 kernel this patch will update the FM driver
accordingly.
Signed-off-by: Manjunatha Halli <manjunatha_halli@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Stop including <linux/delay.h> in x86 header files which don't
need it. This will let the compiler complain when this header is
not included by source files when it should, so that
contributors can fix the problem before building on other
architectures starts to fail.
Credits go to Geert for the idea.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: James E.J. Bottomley <James.Bottomley@suse.de>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
LKML-Reference: <20110325152014.297890ec@endymion.delvare>
[ this also fixes an upstream build bug in drivers/media/rc/ite-cir.c ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Fix the following compile failure:
drivers/media/rc/ite-cir.c: In function 'ite_decode_bytes':
drivers/media/rc/ite-cir.c:190: error: implicit declaration of function 'generic_find_next_le_bit'
drivers/media/rc/ite-cir.c:199: error: implicit declaration of function 'generic_find_next_zero_le_bit'
Caused by commit 620a32bba4 ("[media] rc: New rc-based ite-cir driver
for several ITE CIRs") interacting with commit c4945b9ed4
("asm-generic: rename generic little-endian bitops functions").
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (442 commits)
[media] videobuf2-dma-contig: make cookie() return a pointer to dma_addr_t
[media] sh_mobile_ceu_camera: Do not call vb2's mem_ops directly
[media] V4L: soc-camera: explicitly require V4L2_BUF_TYPE_VIDEO_CAPTURE
[media] v4l: soc-camera: Store negotiated buffer settings
[media] rc: interim support for 32-bit NEC-ish scancodes
[media] mceusb: topseed 0x0011 needs gen3 init for tx to work
[media] lirc_zilog: error out if buffer read bytes != chunk size
[media] lirc: silence some compile warnings
[media] hdpvr: use same polling interval as other OS
[media] ir-kbd-i2c: pass device code w/key in hauppauge case
[media] rc/keymaps: Remove the obsolete rc-rc5-tv keymap
[media] remove the old RC_MAP_HAUPPAUGE_NEW RC map
[media] rc/keymaps: Rename Hauppauge table as rc-hauppauge
[media] rc-rc5-hauppauge-new: Fix Hauppauge Grey mapping
[media] rc-rc5-hauppauge-new: Add support for the old Black RC
[media] rc-rc5-hauppauge-new: Add the old control to the table
[media] rc-winfast: Fix the keycode tables
[media] a800: Fix a few wrong IR key assignments
[media] opera1: Use multimedia keys instead of an app-specific mapping
[media] dw2102: Use multimedia keys instead of an app-specific mapping
...
Fix up trivial conflicts (remove/modify and some real conflicts) in:
arch/arm/mach-omap2/devices.c
drivers/staging/Kconfig
drivers/staging/Makefile
drivers/staging/dabusb/dabusb.c
drivers/staging/dabusb/dabusb.h
drivers/staging/easycap/easycap_ioctl.c
drivers/staging/usbvideo/usbvideo.c
drivers/staging/usbvideo/vicam.c
The cell's platform_data is now accessed with a helper function;
change clients to use that, and remove the now-unused data_size.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The cell's platform_data is now accessed with a helper function;
change clients to use that, and remove the now-unused data_size.
Note that the mfd's platform_data is marked __devinitdata. This
is still correct in all cases except for the timbgpio driver, whose
remove hook has been changed to no longer reference the pdata.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
dma_addr_t may not fit into void* on some architectures. To be safe, make
vb2_dma_contig_cookie() return a pointer to dma_addr_t and dereference it
in vb2_dma_contig_plane_paddr() back to dma_addr_t.
Signed-off-by: Pawel Osciak <pawel@osciak.com>
Reported-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use vb2_dma_contig_plane_paddr to retrieve a physical address for a plane
instead of calling an internal mem_ops callback.
Signed-off-by: Pawel Osciak <pawel@osciak.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The soc-camera core accesses the "pix" member of the struct v4l2_format::fmt
union, which is only valid for V4L2_BUF_TYPE_VIDEO_CAPTURE streams. This
patch adds explicit checks for this to {g,s,try}_fmt methods.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This fixes the problem in which a host driver
sets a personalized sizeimage or bytesperline field,
and gets ignored when doing G_FMT.
Signed-off-by: Sergio Aguirre <saaguirre@ti.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The Apple and TiVo remotes I've got use an NEC-ish protocol, but rather
than a command/not_command pair, they have what appear to be vendor ID
bytes. This change makes the NEC decoder warn if the command/not_command
checksum fails, but then passes along a full 32-bit scancode for keymap
lookup. This change should make no difference for existing keymaps,
since they simply won't have 32-bit scancodes, but allows for a 32-bit
keymap. At the moment, that'll have to be uploaded by the user, but I've
got Apple and TiVo remote keymaps forthcoming.
In the long run (2.6.40, hopefully), we should probably just always use
all 32 bits for all NEC keymaps, but this should get us by for 2.6.39.
(Note that a few of the TiVo keys actuallly *do* pass the command
checksum, so for now, the keymap for this remote will have to be a mix
of 24-bit and 32-bit scancodes, but so be it).
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The hdpvr's IR part, in short, sucks. As observed with a usb traffic
sniffer, the Windows software for it uses a polling interval of 405ms.
Its still not behaving as well as I'd like even with this change, but
this inches us closer and closer to that point...
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The new hauppauge key tables use both device code button code.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This keymap were used for the Hauppauge Black remote controller
only. It also contains some keycodes not found there. As the
Hauppauge Black is now part of the hauppauge keymap, just remove
it.
Also, remove the modprobe hacks to select between the Gray
and the Black versions of the remote controller as:
- Both are supported by default by the keymap;
- If the user just wants one keyboard supported,
it is just a matter of changing the keymap via
the userspace tool (ir-keytable), removing
the keys that he doesn't desire. As ir-keytable
auto-loads the keys via udev, this is better than
obscure modprobe parameters.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
The rc-hauppauge-new map is a messy thing, as it bundles 3
different remote controllers as if they were just one,
discarding the address byte. Also, some key maps are wrong.
With the conversion to the new rc-core, it is likely that
most of the devices won't be working properly, as the i2c
driver and the raw decoders are now providing 16 bits for
the remote, instead of just 8.
delete mode 100644 drivers/media/rc/keymaps/rc-hauppauge-new.c
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
There are two "hauppauge-new" keymaps, one with protocol
unknown, and the other with the protocol marked accordingly.
However, both tables are miss-named.
Also, the old rc-hauppauge-new is broken, as it mixes
three different controllers as if they were just one.
This patch solves half of the problem by renaming the
correct keycode table as just rc-hauppauge. This table
contains the codes for the four different types of
remote controllers found on Hauppauge cards, properly
mapped with their different addresses.
create mode 100644 drivers/media/rc/keymaps/rc-hauppauge.c
delete mode 100644 drivers/media/rc/keymaps/rc-rc5-hauppauge-new.c
[Jarod: fix up RC_MAP_HAUPPAUGE defines]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
The keys for the old black were messed with the ones for the
hauppauge grey. Fix it.
Also, fixes some keycodes and order the keys according with
the way they appear inside the remote controller.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Hans borrowed me an old Black Hauppauge RC. Thanks to that, we
can fix the RC5 table for Hauppauge.
Thanks-to: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Adds the old grey remote controller to Hauppauge table.
Hans borrowed me an old gray Hauppauge RC. Thanks to that, we
can fix the RC5 table for Hauppauge.
Thanks-to: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
One of the remotes has a picture available at:
http://lirc.sourceforge.net/remotes/leadtek/Y04G0004.jpg
As there's one variant with a set direction keys plus vol/chann
keys, and the same table is used for both models, change it to
represent all keys, avoiding the usage of weird function keys.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
This driver uses an app-specific keymap for one of the tables. This
is wrong. Instead, use the standard keycodes.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
This driver uses an app-specific keymap for one of the tables. This
is wrong. Instead, use the standard keycodes.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Using xev and testing the "Windows" key on a normal keyboard, it
is mapped as KEY_LEFTMETA. So, as this is the standard code for
it, use it, instead of a generic, meaningless KEY_PROG1.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Those KEY_PROG[n] keys were used on places where the developer
didn't know for sure what key should be used. On several cases,
using KEY_RED, KEY_GREEN, KEY_YELLOW would be enough. On others,
there are specific keys for that already.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Each keyboard map were using a different definition for
the Source/Video Source key.
Behold Columbus were the only one using KEY_PROPS.
As we want to standardize those keys at X11 and at
userspace applications, we need to use just one code
for it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
On a few places, KEY_MHP were used for snapshots. However, KEY_CAMERA
is used for it on all the other keyboards that have a snapshot/Picture
button.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Make the hdpvr's i2c master implementation more closely mirror that of
the pvrusb2 driver. Currently makes no significant difference in IR
reception behavior with ir-kbd-i2c (i.e., it still sucks).
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: Juan J. Garcia de Soria <skandalfo@gmail.com>
Cc: Stephan Raue <stephan@openelec.tv>
Cc: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is a second version of an rc-core based driver for the ITE Tech IT8712F
CIR and now for a pair of other variants of the IT8512 CIR too.
This driver should replace the lirc_it87 and lirc_ite8709 currently living in
the LIRC staging directory.
The driver should support the ITE8704, ITE8713, ITE8708 and ITE8709 (this last
one yet untested) PNP ID's.
The code doesn'te reuse code from the pre-existing LIRC drivers, but has been
written from scratch using the nuvoton.cir driver as a skeleton.
This new driver shouldn't exhibit timing problems when running under load (or
with interrupts disabled for relatively long times). It works OOTB with the
RC6 MCE remote bundled with the ASUS EEEBox. TX support is implemented, but
I'm unable to test it since my hardware lacks TX capability.
Signed-off-by: Juan J. Garcia de Soria <skandalfo@gmail.com>
Tested-by: Stephan Raue <stephan@openelec.tv>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As the code in saa7134-input is not a module, but the config for it is
set as a boolean instead of a tristate, this causes a strange dependency
on RC_CORE.
VIDEO_SAA7134_RC (which determines if saa7134-input.o is built) depends
on RC_CORE and VIDEO_SAA7134. If VIDEO_SAA7134 is compiled as 'y' but
RC_CORE is compiled as 'm' VIDEO_SAA7134_RC can still be set to 'y'
which causes undefined symbols that it needs from RC_CORE.
The simplest solution is to not allow VIDEO_SAA7134_RC be enabled if
RC_CORE compiled as a module (m) and VIDEO_SA7134 is compiled into the
kernel (y).
Suggested-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: Michal Marek <mmarek@suse.cz>
Cc: linux-kbuild <linux-kbuild@vger.kernel.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch fixes a bug in gspca, more precisely in alt_xfer().
This function looks for an input transfer endpoint in an alternate setting.
By default it returns the first endpoint corresponding to the transfer type
indicated in parameter.
But with some USB devices, the first endpoint corresponding to the transfer
type is not always an INPUT endpoint but an OUTPUT one.
This patch adds the endpoint direction test to be sure to return an INPUT endpoint
Signed-off-by: Patrice CHOTARD <patricechotard@free.fr>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
No 352x288 for Ds3303 and no 320x240 for Generic802.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Rather than guess which driver supports core priority handling, require drivers
that do to explicitly set the V4L2_FL_USE_FH_PRIO flag in video_device.
Updated the core prio handling accordingly and set the flag in the three
drivers that do.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
ivtv-ioctl cast the 'void *fh' directly to 'ivtv_open_id *'. This should be
done properly with a contained_of since the 'void *fh' is really a
'struct v4l2_fh *'.
It worked because the v4l2_fh field is also the first field in the ivtv_open_id
struct, but it is not clean code.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use core-assisted locking so .ioctl can be replaced by .unlocked_ioctl.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The video_device struct has proper ref counting and its release function
will be called when the last user releases it. But no such support was
available for struct v4l2_device. This made it hard to determine when a
USB driver can release the device if it has multiple device nodes.
With one device node it is easy of course, since when the device node is
released, the whole device can be released.
This patch adds refcounting to v4l2_device. When registering device nodes
the v4l2_device refcount will be increased, when releasing device nodes
it will be decreased. The (optional) release function will be called when
the last device node was released.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
VIDIOC_S/G_PRIORITY handling is now done by the v4l2 core framework.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Drivers that use v4l2_fh can now use the core framework support of g/s_priority.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Several drivers need to do something when the first filehandle is opened
or the last filehandle is closed. Most implement some use count mechanism,
but if they use v4l2_fh, then you can also just check if this is the only
filehandle for the device node. A simple helper function can do this.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add two new functions: v4l2_fh_open allocates and initializes a struct v4l2_fh
based on a struct file pointer and v4l2_fh_release releases and frees a struct
v4l2_fh.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Integrate the v4l2_prio_state into the core, ready for use.
One struct v4l2_prio_state is added to v4l2_device and a pointer
to a prio state is added to video_device.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We are going to move priority handling into the v4l2 core. As a consequence
the v4l2_prio helper functions need to be moved into the core videodev
module as well to prevent circular dependencies.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
On my AverMedia AverTV Studio 507, key up events are no longer sent after
a suspend-to-disk/resume cycle, resulting in "stuck" keys.
Apparently, for key up events to be generated, a certain GPIO pin must be set.
Currently it's set in saa7134_input_init1(), but that function is not called
on device resume. I suggest that code be moved to __saa7134_ir_start(), which
is called both on init and resume.
Signed-off-by: Vadim Solomin <vadic052@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The CellsCoeffs arrays are [3][6][5] not [2][6][5].
Signed-off-by: Dan Carpenter <error27@gmail.com>
Cc: Igor M. Liplianin <liplianin@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We use err to store negative error codes so it should be signed. And
if we return an error from stv0367_get_tuner_freq() that needs to be
handled properly as well. (param->frequency is a u32).
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The code that checks the OLPC serial port is never built at the moment,
because CONFIG_OLPC_XO_1_5 doesn't exist and probably won't be added.
Fix it so that it gets compiled in, only executes on OLPC laptops, and
move the check into the probe routine.
The compiler is smart enough to eliminate this code when CONFIG_OLPC=n
(due to machine_is_olpc() always returning false).
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
These bubble button remote controls appear to be generic from China.
These are the three variants known to be supplied with DM04/QQBOX DVB-S
They could well be supplied with other devices from the region.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use 32 bit decoding to add support for more than one variant of remote
control.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Old versions of these boxes have the BS2F7HZ0194 tuner module on
both the LME2510 and LME2510C.
Firmware dvb-usb-lme2510-s0194.fw and/or dvb-usb-lme2510c-s0194.fw
files are required.
See Documentation/dvb/lmedm04.txt
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Error path in file drivers/media/video/tlg2300/pd-video.c:
1. First mutex_unlock on &pd->lock in line 767 (in function that
called from line 805)
2. Second in line 806
805 pd_vidioc_s_fmt(pd, &f->fmt.pix);
806 mutex_unlock(&pd->lock);
Found by Linux Device Drivers Verification Project
Signed-off-by: Alexander Strakh <strakh@ispras.ru>
Acked-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
wl1273_device->work is unused. Remove it along with the spurious
flush_scheduled_work() call in wl1273_fm_module_exit().
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Matti Aaltonen <matti.j.aaltonen@nokia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
On Thu, 17 Feb 2011, Matthias Schwarzott wrote:
> On Sunday 06 February 2011, Jesper Juhl wrote:
> > If the memory allocation to 'state' succeeds but we jump to the 'error'
> > label before 'state' is assigned to fe->tuner_priv, then the call to
> > 'zl10036_release(fe)' at the 'error:' label will not free 'state', but
> > only what was previously assigned to 'tuner_priv', thus leaking the memory
> > allocated to 'state'.
> > There are may ways to fix this, including assigning the allocated memory
> > directly to 'fe->tuner_priv', but I did not go for that since the
> > additional pointer derefs are more expensive than the local variable, so I
> > just added a 'kfree(state)' call. I guess the call to 'zl10036_release'
> > might not even be needed in this case, but I wasn't sure, so I left it in.
> >
> Yeah, that call to zl10036_release can be completely eleminated.
> Another thing is: jumping to the error label only makes sense when memory was
> already allocated. So the jump in line 471 can be replaced by "return NULL",
> as the other error handling before allocation:
> if (NULL == config) {
> printk(KERN_ERR "%s: no config specified", __func__);
> goto error;
> }
>
> I suggest to improve the patch to clean the code up when changing that.
>
> But I am fine with commiting this patch also if you do not want to change it.
>
Thank you for your feedback. It makes a lot of sense.
Changing it is not a problem :)
How about the updated patch below?
If the memory allocation to 'state' succeeds but we jump to the 'error'
label before 'state' is assigned to fe->tuner_priv, then the call to
'zl10036_release(fe)' at the 'error:' label will not free 'state', but
only what was previously assigned to 'tuner_priv', thus leaking the memory
allocated to 'state'.
This patch fixes the leak and also does not jump to 'error:' before mem
has been allocated but instead just returns. Also some small style
cleanups.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
mem->dma_handle is a dma address obtained by dma_alloc_coherent which
needn't be a physical address in presence of IOMMU, as
a hardware IOMMU can (and most likely) will return a bus address where
physical != bus address.
So ensure we are remapping (remap_pfn_range) the right page in
__videobuf_mmap_mapper by using virt_to_phys(mem->vaddr) and not
mem->dma_handle.
While at it, use PFN_DOWN instead of explicit shift.
[mchehab@redhat.com: Fix compilation breakage due to the lack of a comma]
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The scheme used to index format in uvc_fixup_video_ctrl() is not robust:
format index is based on descriptor ordering, which does not necessarily
match bFormatIndex ordering. Searching for first matching format will
prevent uvc_fixup_video_ctrl() from using the wrong format/frame to make
adjustments.
Signed-off-by: Stephan Lachowsky <stephan.lachowsky@maxim-ic.com>
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Split FW download packages smarter way and bug free. Implementation is
based of Andrea Merello's example he provided for tda18218 driver.
Count remaining FW bytes down in loop instead of division and modulo
combination used earlier.
Thanks to: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Cc: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Quick test shows that FW must be running before other checks
so make it happen earlier.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Split FW download packages smarter way and bug free. Implementation is
based of Andrea Merello's example he provided for tda18218 driver.
Count remaining FW bytes down in loop instead of division and modulo
combination used earlier.
Thanks-to: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Cc: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remote used for TerraTec Cinergy T Stick RC.
Keytable from Martin Groszhauser <mgroszhauser@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Cc: Martin Groszhauser <mgroszhauser@gmail.com>
Cc: TerraTux <TerraTux@terratec.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Patch from Ian Armstrong.
I've encountered a couple of problems with the current af9015 driver as
supplied with the 2.6.37 kernel, that the attached patch appears to fix. (I've
generated this patch against the current v4l-dvb git).
Some key-presses are lost. A key-press is only generated upon 'valid' data
(buf[14] == (u8) ~buf[15]), but the buffer is wiped before this check.
Sometimes the 15th byte has not been set at the time of read, so the data
isn't valid & ignored. On the next poll the 15th byte has been set, but the
rest of the data was wiped previously, so the data is still invalid & the key
is lost.
Weird repeat error, where an old key press is sometimes repeated in error. ie.
button sequence '1 (pause) 2 (pause) 3 (pause) 4' generates output like '1
(pause) 2 (pause) 23 (pause) 4'. The current driver zeroes the data for the
key pushed, but sometimes this data is already zero but with other bytes set
suggesting a repeat code. This results in the last key being incorrectly
repeated.
This patch attempts to reduce the risk of a missed key-press & also stop the
random repeat of an old key-press when a new key is pressed.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This file contains functions for the auto gain.
It must be used with the new control mechanism.
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Not only the qx3 microscope has a button, but some cameras too. Tested
with the Trust sp@cecam 100 (and with a creative and ezcam without button).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
allows the driver to proceed and initialize the below two values
even if the kmalloc() fails.
hdw->std_info_enum.def.type_enum.value_names
hdw->std_info_enum.def.type_enum.count
Signed-off-by: Xiaochen Wang <wangxiaochen0@gmail.com>
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This was caught via a compiler warning. Amazingly enough this bit of
benign dreck dates all the way back to 2008.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Memory allocated by alloc_page() function might contain some potentially
important data from other system processes. The patch adds a flag to
zero the allocated page before giving it to videobuf2 (and then to
userspace).
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
__vb2_queue_free function doesn't really return anything useful. This patch
removes support for the return value to simplify the code.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Return immediately if the target number of buffers is the same as
the current one and memory access type doesn't change.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch fixes two minor memory leaks in videobuf2-dma-sg module. They
might happen only in case some other operations (like memory allocation)
failed.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch fixes 2 minor bugs in videobuf2 core:
1. Queue should be reallocated if one change the memory access
method without changing the number of buffers.
2. In case of REQBUFS(0), the request should not be passed to the
driver.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use pix_mp member of struct v4l2_format to return a format
description rather than pix. Also fill in the plane_fmt array.
This is a missing bit of conversion to the multiplanar API.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use pr_debug instead of printk so it is possible to control
debug traces at runtime.
E.g. to enable debug trace in file fimc-core.c use command:
echo -n 'file fimc-core.c +p' > /sys/kernel/debug/dynamic_debug/control
or
echo -n 'file fimc-core.c -p' > /sys/kernel/debug/dynamic_debug/control
to disable.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Allow the MIPI-CSI data alignment to be defined in the board setup
as it may be different across various camera sensors.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add num_clients field to struct s5p_fimc_isp_info to define exactly
size of clients array which simplifies a bit the sensors management.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Rework the locking in m2m driver to assure proper operation on SMP systems.
When job_abort or stop_streaming was called to immediately shutdown
a memory-to-memory transaction video buffers scheduled for processing
were never returned to vb2 and v4l2_m2m_job_finish was not called
which led to hanging.
Correct this and also return the unprocessed buffers to vb2 marking
them as erroneous, in case the end of frame interrupt do not occur.
Reported-by: Sewoon Park <seuni.park@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In some cases fimc H/W did not stop although there were no output
buffers available. So the capture deactivation interrupt routine
is modified and the state of ST_CAPT_RUN is cleared only
in the LAST-IRQ call.
After LAST-IRQ is generated, H/W pointer will be skipped by 1 frame.
(reference by user manual) So, S/W pointer should be increased too.
Reviewed-by Jonghun Han <jonghun.han@samsung.com>
Signed-off-by: Sungchun Kang <sungchun.kang@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Two xc5000 tuners connected to same i2c bus.
Experiments shows that situation when one tuner is not initialized
while other is tuned to channel causes TS errors.
Signed-off-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
CI reset takes several seconds on some CAM,
so there is no need to lock mutex all that time.
Also we need not to preserve CI's reset bits in
CIBUSCTRL register, they are handled automatically by FPGA.
Set it to 0 explicitly in order to not reset wrong CAM.
Signed-off-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
cpia2_core.c:529:14: warning: variable 'dir' set but not used [-Wunused-but-set-variable]
cpia2_core.c:526:5: warning: variable 'block_index' set but not used [-Wunused-but-set-variable]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
au0828-dvb.c:99:6: warning: variable 'ptr' set but not used [-Wunused-but-set-variable]
au0828-video.c:1180:25: warning: variable 'maxheight' set but not used [-Wunused-but-set-variable]
au0828-video.c:1180:15: warning: variable 'maxwidth' set but not used [-Wunused-but-set-variable]
bttv-input.c:196:16: warning: variable 'current_jiffies' set but not used [-Wunused-but-set-variable]
Those variables are not used at all, so just remove them.
Cc: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Functions defined in a header should be static inline. This prevents
compile warnings like:
'altera_ci_tuner_reset' defined but not used
(Actually appeared in the media backwards compatibility build).
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/video/cx88/cx88-alsa.c: In function 'cx88_audio_initdev':
drivers/media/video/cx88/cx88-alsa.c:881:20: warning: 'core' may be used uninitialized in this function
The compiler doesn't understand that snd_cx88_create fills in the core
pointer. So just initialize it to NULL.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/radio/wl128x/fmdrv_common.c: In function 'recv_tasklet':
drivers/media/radio/wl128x/fmdrv_common.c:274:4: warning: format '%d' expects type 'int', but argument 4 has type 'long unsigned int'
The result of sizeof() should be printed with %zu.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/video/cx23885/altera-ci.c: In function 'altera_hw_filt_init':
drivers/media/video/cx23885/altera-ci.c:671:2: warning: cast from pointer to integer of different size
drivers/media/video/cx23885/altera-ci.c: In function 'altera_ci_init':
drivers/media/video/cx23885/altera-ci.c:739:2: warning: cast from pointer to integer of different size
Use %p instead of 0x%x to print addresses.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/dvb/frontends/stv0367.c: In function 'stv0367ter_lock_algo':
drivers/media/dvb/frontends/stv0367.c:1315:2: warning: cast from pointer to integer of different size
Use %p to print addresses instead of 0x%x.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/common/tuners/tuner-xc2028.c: In function 'generic_set_freq':
drivers/media/common/tuners/tuner-xc2028.c:936:15: warning: comparison between 'enum tuner_mode' and 'enum v4l2_tuner_type'
Argument type was enum tuner_mode, but should have been enum v4l2_tuner_type.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Replace the omap_pm_set_min_bus_tput() with a callback to board code.
This makes the omap3isp driver compilable as a module, and lets board
code manage OMAP PM details depending on board requirements.
Signed-off-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of returning an error when receiving an ioctl call with an
unsupported command, forward the call to the subdev core::ioctl handler.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds the VIDIOC_SUBDEV_S_CROP and G_CROP ioctls to the
userland API. CROPCAP is not implemented because it's redundant.
Signed-off-by: Antti Koskipaa <akoskipa@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The three new ioctl VIDIOC_SUBDEV_ENUM_FRAME_INTERVAL,
VIDIOC_SUBDEV_G_FRAME_INTERVAL and VIDIOC_SUBDEV_S_FRAME_INTERVAL can be
used to enumerate and configure a subdev's frame rate from userspace.
Two new video::g/s_frame_interval subdev operations are introduced to
support those ioctls. The existing video::g/s_parm operations are
deprecated and shouldn't be used anymore.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a userspace API to get, set and enumerate the media format on a
subdev pad.
The format at the output of a subdev usually depends on the format at
its input(s). The try format operation is thus not suitable for probing
format at individual pads, as it can't modify the device state and thus
can't remember the format tried at the input to compute the output
format.
To fix the problem, pass an extra argument to the get/set format
operations to select the 'try' or 'active' format.
The try format is used when probing the subdev. Setting the try format
must not change the device configuration but can store data for later
reuse. Data storage is provided at the file-handle level so applications
probing the subdev concurently won't interfere with each other.
The active format is used when configuring the subdev. It's identical to
the format handled by the usual get/set operations.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
V4L2 sub-devices store pad formats and crop settings in the file handle.
To let drivers initialize those settings properly, add an open operation
that is called when the subdev is opened as well as a corresponding
close operation.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Used for storing subdev information per file handle and hold V4L2 file
handle.
Signed-off-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Signed-off-by: Antti Koskipaa <akoskipa@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For consistency with the V4L2_MBUS_FMT_Y10_1X10 format.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
V4L2 subdevices are media entities. As such they need to inherit from
(include) the media_entity structure.
When registering/unregistering the subdevice, the media entity is
automatically registered/unregistered. The entity is acquired on device
open and released on device close.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
V4L2 devices are media entities. As such they need to inherit from
(include) the media_entity structure.
When registering/unregistering the device, the media entity is
automatically registered/unregistered. The entity is acquired on device
open and released on device close.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The pointer will later be used to register/unregister media entities
when registering/unregistering a v4l2_subdev or a video_device.
With the introduction of media devices, device drivers need to store a
pointer to a driver-specific structure in the device's drvdata.
v4l2_device can't claim ownership of the drvdata anymore.
To maintain compatibility with drivers that rely on v4l2_device storing
a pointer to itself in the device's drvdata, v4l2_device_register() will
keep doing so if the drvdata is NULL.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Drivers often need to associate pipeline objects to entities, and to
take stream state into account when configuring entities and links. The
pipeline API helps drivers manage that information.
When starting streaming, drivers call media_entity_pipeline_start(). The
function marks all entities connected to the given entity through
enabled links, either directly or indirectly, as streaming. Similarly,
when stopping the stream, drivers call media_entity_pipeline_stop().
The media_entity_pipeline_start() function takes a pointer to a media
pipeline and stores it in every entity in the graph. Drivers should
embed the media_pipeline structure in higher-level pipeline structures
and can then access the pipeline through the media_entity structure.
Link configuration will fail with -EBUSY by default if either end of the
link is a streaming entity, unless the link is marked with the
MEDIA_LNK_FL_DYNAMIC flag.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Create the following ioctl and implement it at the media device level to
setup links.
- MEDIA_IOC_SETUP_LINK: Modify the properties of a given link
The only property that can currently be modified is the ENABLED link
flag to enable/disable a link. Links marked with the IMMUTABLE link flag
can not be enabled or disabled.
Enabling or disabling a link has effects on entities' use count. Those
changes are automatically propagated through the graph.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Create the following two ioctls and implement them at the media device
level to enumerate entities, pads and links.
- MEDIA_IOC_ENUM_ENTITIES: Enumerate entities and their properties
- MEDIA_IOC_ENUM_LINKS: Enumerate all pads and links for a given entity
Entity IDs can be non-contiguous. Userspace applications should
enumerate entities using the MEDIA_ENT_ID_FLAG_NEXT flag. When the flag
is set in the entity ID, the MEDIA_IOC_ENUM_ENTITIES will return the
next entity with an ID bigger than the requested one.
Only forward links that originate at one of the entity's source pads are
returned during the enumeration process.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Create the following ioctl and implement it at the media device level to
query device information.
- MEDIA_IOC_DEVICE_INFO: Query media device information
The ioctl and its data structure are defined in the new kernel header
linux/media.h available to userspace applications.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Due to the wide differences between drivers regarding power management
needs, the media controller does not implement power management.
However, the media_entity structure includes a use_count field that
media drivers can use to track the number of users of every entity for
power management needs.
The use_count field is owned by media drivers and must not be touched by
entity drivers. Access to the field must be protected by the media
device graph_mutex lock.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add media entity graph traversal. The traversal follows enabled links by
depth first. Traversing graph backwards is prevented by comparing the next
possible entity in the graph with the previous one. Multiply connected
graphs are thus not supported.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Vimarsh Zutshi <vimarsh.zutshi@gmail.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As video hardware pipelines become increasingly complex and
configurable, the current hardware description through v4l2 subdevices
reaches its limits. In addition to enumerating and configuring
subdevices, video camera drivers need a way to discover and modify at
runtime how those subdevices are connected. This is done through new
elements called entities, pads and links.
An entity is a basic media hardware building block. It can correspond to
a large variety of logical blocks such as physical hardware devices
(CMOS sensor for instance), logical hardware devices (a building block
in a System-on-Chip image processing pipeline), DMA channels or physical
connectors.
A pad is a connection endpoint through which an entity can interact with
other entities. Data (not restricted to video) produced by an entity
flows from the entity's output to one or more entity inputs. Pads should
not be confused with physical pins at chip boundaries.
A link is a point-to-point oriented connection between two pads, either
on the same entity or on different entities. Data flows from a source
pad to a sink pad.
Links are stored in the source entity. To make backwards graph walk
faster, a copy of all links is also stored in the sink entity. The copy
is known as a backlink and is only used to help graph traversal.
The entity API is made of three functions:
- media_entity_init() initializes an entity. The caller must provide an
array of pads as well as an estimated number of links. The links array
is allocated dynamically and will be reallocated if it grows beyond the
initial estimate.
- media_entity_cleanup() frees resources allocated for an entity. It
must be called during the cleanup phase after unregistering the entity
and before freeing it.
- media_entity_create_link() creates a link between two entities. An
entry in the link array of each entity is allocated and stores pointers
to source and sink pads.
When a media device is unregistered, all its entities are unregistered
automatically.
The code is based on Hans Verkuil <hverkuil@xs4all.nl> initial work.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The media_device structure abstracts functions common to all kind of
media devices (v4l2, dvb, alsa, ...). It manages media entities and
offers a userspace API to discover and configure the media device
internal topology.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The media_devnode structure provides support for registering and
unregistering character devices using a dynamic major number. Reference
counting is handled internally, making device drivers easier to write
without having to solve the open/disconnect race condition issue over
and over again.
The code is based on video/v4l2-dev.c.
[mchehab@redhat.com: Remove linux/smp_lock.h include to not break compilation on bisect]
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Provide v4l2_subdevs with v4l2_event support. Subdev drivers only need very
little to support events.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: David Cohen <dacohen@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Pass the control-related ioctls to the subdev driver through the control
framework.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The function isn't small or performance sensitive enough to be inlined.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Create a device node named subdevX for every registered subdev.
As the device node is registered before the subdev core::s_config
function is called, return -EGAIN on open until initialization
completes.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Vimarsh Zutshi <vimarsh.zutshi@gmail.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The two functions are mostly identical. They handle the copy_from_user
and copy_to_user operations related with V4L2 ioctls and call the real
ioctl handler.
Create a __video_usercopy function that implements the core of
video_usercopy and video_ioctl2, and call that function from both.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The patch below removes an extra "l" in the word.
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The patch below removes an extra "l" in the word.
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Related to Acorp DS120 and some revisions of DVBWorld DW2102.
If you read three or more registers at one time, you get wrong value for third etc.
Actually, it didn't affect the driver as it reads registers only by one at a time.
But it needs to correct.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Prof 7500 and TeVii s630, s660, s480 works better now
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Prof 7500 and TeVii s630, s660, s480 works faster now
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The card consist of PCI to USB bridge and USB DVB-S2 receiver.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It is taken from another tree, where it is modified.
Patch to fix that
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Simptoms:
After zapping DVB-S2 channel searching for DVB-S tooks long time.
Now it takes less than a second.
Signed-off-by: Igor M. Liplianin <liplianin@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
dib9000_mbx_send_attr() returns an int. It doesn't work to save
negative error codes in an unsigned char, so I've made "ret" an int
type.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This module implements V4L2 controls for the Texas Instruments
WL1273 FM Radio and handles the communication with the chip.
Signed-off-by: Matti J. Aaltonen <matti.j.aaltonen@nokia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
RADIO_WL1273 needs to make sure that the mfd core is built to avoid
build errors:
ERROR: "mfd_add_devices" [drivers/mfd/wl1273-core.ko] undefined!
ERROR: "mfd_remove_devices" [drivers/mfd/wl1273-core.ko] undefined!
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Matti Aaltonen <matti.j.aaltonen@nokia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add suspend/resume support to the via-camera driver, so that the video
continues streaming over a suspend-resume cycle.
Originally implemented by Jon Corbet.
[mchehab@redhat.com: fix a small CodingStyle issue]
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Based on staging 2.6.39.
This patch is based on Veit Berwig's work.
Signed-off-by: Lukas Fisch <lukas.fisch@gmail.com>
Thanks-to: Veit Berwig <veit.Berwig@fimi.landsh.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
kmalloc() can fail so check whether state->internal is NULL.
append_internal() can return NULL on allocation failures so check that.
Also if we hit the error condition later in the function then there is
a memory leak and we need to call remove_dev() to fix it.
Also Oliver Endriss pointed out an additional leak that I missed in the
first version of this patch.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This has implementation for FM TX functionality.
It communicates with FM V4l2 module and FM common module.
Signed-off-by: Manjunatha Halli <manjunatha_halli@ti.com>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This has implementation for FM RX functionality.
It communicates with FM V4l2 module and FM common module
Signed-off-by: Manjunatha Halli <manjunatha_halli@ti.com>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
These are the sources for the common interfaces required by the
FM V4L2 driver for TI WL127x and WL128x chips.
These implement the FM channel-8 protocol communication with the
chip. This makes use of the Shared Transport as its transport.
Signed-off-by: Manjunatha Halli <manjunatha_halli@ti.com>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This module interfaces V4L2 subsystem and FM common module.
It registers itself with V4L2 as Radio module.
Signed-off-by: Manjunatha Halli <manjunatha_halli@ti.com>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
These are common headers used in FM submodules (FM V4L2,
FM common, FM Rx,and FM TX).
Signed-off-by: Manjunatha Halli <manjunatha_halli@ti.com>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
get_user_pages() may return -errno, such as -EFAULT. So don't blindly use
its return value as an offset into dma->map[] for the next get_user_pages()
call. Since we'll give up and return an error if either fails, don't even
make the second call if the first failed to give us exactly what we were
looking for.
The old code would also call put_page() on as many elements of dma->map[]
as we'd asked for, regardless of how many were valid.
[Andy Walls modified this patch to return -EFAULT instead of -EINVAL
as Paul's observation "I'm not sure -EINVAL is the best return code vs
-EFAULT or -ENOMEM, [...]" was correct. The return value bubbles up
as a return code for write(), for which the V4L2 API spec indicates
EINVAL is incorrect and EFAULT is correct.]
Signed-off-by: Paul Cassella <fortytwo-ivtv@maneteren.bigw.org>
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix the first, botched attempt at preventing direct use of a user pointer in
ivtv_write_vbi().
Reported-by: Dr. David Alan Gilbert <linux@treblig.org>
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
get_user_pages() may return fewer page than we ask for. As we give up and
return an error in this case, we need to put_page() each of the pages we
did get.
[Andy Walls modified the patch, only removing the braces in the 'for'
statement, to eliminate a checkpatch warning.]
Signed-off-by: Paul Cassella <fortytwo-ivtv@manetheren.bigw.org>
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
All necessary parameters already stored in frontend cache.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Variable 'retune' does not make sense.
Loop is not needed for only one try.
Remove unnecessary dprintk's.
Remove a lot of debug messages and delays.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
