The default REP_PERIOD is 33 ms. This doesn't make sense for IR's,
as, in general, an IR repeat scancode is provided at every 110/115ms,
depending on the RC protocol. So, increase its default, to do a
better job avoiding ghost repeat events.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Jarod Wilson <jarod@redhat.com>
The initialisation of vb_type in serialized_open was preventing
REQBUFS from working reliably. Remove it, and move the spinlock into
stream_init for good measure - it's only used when we have a stream
that supports videobuf anyway.
Signed-off-by: Simon Farnsworth <simon.farnsworth@onelan.co.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make sure pdev is not dereferenced when it is null
Signed-off-by: Huzaifa Sidhpurwala <huzaifas@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- Holds the parameters detected by the demod.
- Updated on every call to get_frontend, either through ioctl or when
a frontend event occurs.
- Reset to input parameters after every call to set_frontend, tune or
search/track.
Signed-off-by: Andreas Oberritter <obi@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- Drivers should be able to override properties returned to the user.
- The default values get prefilled from the cache.
Signed-off-by: Andreas Oberritter <obi@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- Use const pointers and remove assignments.
- delivery_system already gets assigned by DTV_DELIVERY_SYSTEM
and dtv_property_cache_sync.
Signed-off-by: Andreas Oberritter <obi@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is supported in DVB-T2 mode, so added to the T/T2 frontend.
Signed-off-by: Steve Kerrison <steve@stevekerrison.com>
Acked-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/common/tuners/mxl5005s.c: In function ‘mxl5005s_set_params’:
drivers/media/common/tuners/mxl5005s.c:4016: warning: enumeration value ‘BANDWIDTH_5_MHZ’ not handled in switch
drivers/media/common/tuners/mxl5005s.c:4016: warning: enumeration value ‘BANDWIDTH_10_MHZ’ not handled in switch
drivers/media/common/tuners/mxl5005s.c:4016: warning: enumeration value ‘BANDWIDTH_1_712_MHZ’ not handled in switch
Signed-off-by: Andreas Oberritter <obi@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/dvb/frontends/drxd_hard.c: In function ‘DRX_Start’:
drivers/media/dvb/frontends/drxd_hard.c:2327: warning: enumeration value ‘BANDWIDTH_5_MHZ’ not handled in switch
drivers/media/dvb/frontends/drxd_hard.c:2327: warning: enumeration value ‘BANDWIDTH_10_MHZ’ not handled in switch
drivers/media/dvb/frontends/drxd_hard.c:2327: warning: enumeration value ‘BANDWIDTH_1_712_MHZ’ not handled in switch
[mchehab@redhat.com: removed the status = status assignment after the switch]
Signed-off-by: Andreas Oberritter <obi@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
[steve@stevekerrison.com: Remove private definitions from cxd2820r that existed before API was defined]
Signed-off-by: Andreas Oberritter <obi@linuxtv.org>
Signed-off-by: Steve Kerrison <steve@stevekerrison.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
ictx->touch is intialied in imon_init_intf1, to the result of calling the
function that contains this code. Thus, in this code, input_free_device
should be called on touch itself.
A simplified version of the semantic match that finds this problem is:
(http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
local idexpression struct input_dev * x;
expression ra,rr;
position p1,p2;
@@
x = input_allocate_device@p1(...)
... when != x = rr
when != input_free_device(x,...)
when != if (...) { ... input_free_device(x,...) ...}
if(...) { ... when != x = ra
when forall
when != input_free_device(x,...)
\(return <+...x...+>; \| return@p2...; \) }
@script:python@
p1 << r.p1;
p2 << r.p2;
@@
cocci.print_main("input_allocate_device",p1)
cocci.print_secs("input_free_device",p2)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Enable the IR support for the Hauppauge HVR-1150 and HVR-1120.
Thanks to Fernando Laudares Camargos for testing the patch.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Cc: Fernando Laudares Camargos <fernando.laudares.camargos@gmail.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is a new rc-core device driver for the IR transceivers made by
RedRat Ltd. (http://redrat.co.uk/). It started out life as an
out-of-lirc-tree lirc driver, maintained in its own repo on sourceforge,
by Stephen Cox. He started porting it to what was then ir-core, and I
finally picked it up about two week ago and did a fairly large overhaul
on it, and its now into a state where I'm fairly comfortable submitting
it here for review and inclusion in the kernel. I'm claiming authorship
of this driver, since while it started out as Stephen's work, its
definitely a derivative work now, at 876 lines added and 1698 lines
removed since grabbing it from sourceforge. Stephen's name is retained
as secondary author though, and credited in the headers. Those
interested in seeing how the changes evolved can (at least for now) look
at this branch in my git tree:
http://git.kernel.org/?p=linux/kernel/git/jarod/linux-2.6-ir.git;a=shortlog;h=refs/heads/redrat3
That won't be around forever though, and I'm doing this as a single
commit to go into mainline. Anyway...
I've successfully tested in-kernel decode of rc5, rc6 and nec remotes,
as well as lirc userspace decode of rc5 and rc6. There are still some
quirks here to sort out with rc5 lirc userspace decode, but I'm working
with the RedRat folks themselves to figure out what's going on there
(rc5 lirc decode works, but you only get an event on key release --
in-kernel rc5 decode behaves perfectly fine). Note that lirc decode of
rc6 is working perfectly. Transmit is also working, tested by pointing
the redrat3 at an mceusb transceiver, which happily picked up the
transmitted signals and properly decoded them.
There's no default remote for this hardware, so its somewhat arbitrarily
set to use the Hauppauge RC5 keymap by default. Easily changed out by
way of ir-keytable and irrelevant if you're using lircd for decode.
CC: Chris Dodge <chris@redrat.co.uk>
CC: Andrew Vincer <Andrew.Vincer@redrat.co.uk>
CC: Stephen Cox <scox_nz@yahoo.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Continuing with IR transmit after resuming from suspend seems fairly
useless, given that the only place we can actually end up suspending is
after IR has been send and we're simply mdelay'ing. Lets simplify the
resume path by just waiting on tx to complete in the suspend path, then
we know we can't be transmitting on resume, and reinitialization of the
hardware registers becomes more straight-forward.
CC: Juan Jesús García de Soria <skandalfo@gmail.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There was some rather odd spacing in a few of the ite8709-specific
functions that made it hard to read those sections of code. This is just
a simple reformatting.
CC: Juan Jesús García de Soria <skandalfo@gmail.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Just recently acquired an Asus Eee Box PC with an onboard IR receiver
driven by ite-cir (ITE8713 sub-variant). Works out of the box with the
ite-cir driver in 2.6.39, but stops working after a suspend/resume
cycle. Its fixed by simply reinitializing registers after resume,
similar to what's done in the nuvoton-cir driver. I've not tested with
any other ITE variant, but code inspection suggests this should be safe
on all variants.
Reported-by: Stephan Raue <sraue@openelec.tv>
CC: Juan Jesús García de Soria <skandalfo@gmail.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- Eliminate a possible circular locking lockdep warning
- Make sure we don't try to unregister a vfd on a device w/a vga screen
- Always free imon context after devices are removed (display_close can
just error out w/no context)
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- Set a default timeout (matching mceusb.c) and use
ir_raw_event_store_with_filter, which leads to better behavior when
using lirc userspace decoding with this hardware
- Fill in rx_resolution with the value we're using here (50us)
- Wire up input phys and device parent pointer
- Use device_init_wakeup() instead of device_set_wakeup_*()
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The M420 format is used by the Microsoft LifeCam Studio HD.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[laurent.pinchart@ideasonboard.com: split into v4l/uvcvideo patches]
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support to uvc driver for NOMMU arch including add function
uvc_queue_get_unmapped_area() and make some changes in uvc_queue_mmap().
So that uvc camera can be used on nommu arch like blackfin.
Signed-off-by: Bob Liu <lliubbo@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This camera driver supports only rising edge, which is the default
setting of the device. The function mt9m111_setup_pixfmt() overwrites
this setting. So the driver actually uses falling edge.
This patch corrects that.
Signed-off-by: Teresa Gámez <t.gamez@phytec.de>
[g.liakhovetski@gmx.de: removed superfluous register write]
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Tested-by: Teresa Gámez <t.gamez@phytec.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The setup of the pixel clock is done wrong in the mt9v022 driver.
The 'Invert Pixel Clock' bit has to be set to 1 for falling edge
and not for rising. This is not clearly described in the data
sheet.
Tested on pcm037 and pcm027/pcm990.
Signed-off-by: Teresa Gámez <t.gamez@phytec.de>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
soc_mbus_get_fmtdesc() returning NULL means only, that no standard
mediabus code -> fourcc conversion is known, this shouldn't be treated
as an error by drivers.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add new look-up entries for all mediabus codes, for which respective
fourcc codes exist.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
12-bit formats, similar to YUV 4:2:0 occupy 3 bytes for each two pixels
and cannot be described by any of the existing SOC_MBUS_PACKING_* macros.
This patch adds a new one SOC_MBUS_PACKING_1_5X8 to describe such
formats and extends soc_mbus_samples_per_pixel() to support it.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since V4L2_MBUS_FMT_* codes have become large and sparse, they cannot
be used as array indices anymore.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Recently mediabus pixel format codes have become a part of the user-
space API, at which time their values also have been changed from
contiguous numbers, running from 0 to sparse numbers with values
around 0x1000, 0x2000, 0x3000... This made them unsuitable for the
use as array indices. This patch switches soc-camera internal format
look-ups to not depend on values of those macros.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add an soc-camera host livecrop operation to implement live zoom. If
a host driver implements it, it should take care to preserve output
frame format, then live crop doesn't break streaming.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The .stop_streaming() videobuf2 operation has to be implemented to
guarantee, that video buffers are not written to after a STREAMOFF.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The .stop_streaming() videobuf2 operation has to be implemented to
guarantee, that video buffers are not written to after a STREAMOFF.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add the subdev driver for the MIPI CSIS units available in S5P and
Exynos4 SoC series. This driver supports both CSIS0 and CSIS1
MIPI-CSI2 receivers.
The driver requires Runtime PM to be enabled for proper operation.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
s5p-fimc now also implements a camera capture video node so move
it under the "Video capture devices" Kconfig menu. Also update
the entry to reflect the driver's coverage of EXYNOS4 SoCs and
separate the Makefile entry from the soc-camera drivers set.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use the expression "video stream" instead of "color camera" which is
more correct as the driver supports the RGB and IR image on the same
endpoint.
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Move large communications buffers out of stack and into device
structure. This prevents the frame size from being >1kB and fixes a
compiler warning when CONFIG_FRAME_WARN=1024:
drivers/media/video/gspca/kinect.c: In function ‘send_cmd.clone.0’:
drivers/media/video/gspca/kinect.c:202: warning: the frame size of 1548 bytes is larger than 1024 bytes
Reported-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Drew Fisher <drew.m.fisher@gmail.com>
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- Return values should not be ORed. Abort early instead.
- Return -EINVAL instead of -1.
Signed-off-by: Andreas Oberritter <obi@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch removes the remaining on-stack buffer for USB DMA transfer.
This patch also reduces the stack memory usage.
Cc: stable@kernel.org
Cc: Florian Mickler <florian@mickler.org>
Signed-off-by: Olivier Grenie <olivier.grenie@dibcom.fr>
Signed-off-by: Patrick Boettcher <patrick.boettcher@dibcom.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This fixes autoloading of the module.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
