Smeta write errors were previously ignored. Skip these
lines instead and throw them back on the free
list, so the chunks will go through a reset cycle
before we attempt to use the line again.
Signed-off-by: Hans Holmberg <hans.holmberg@cnexlabs.com>
Reviewed-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <mb@lightnvm.io>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Write failures should not happen under normal circumstances,
so in order to bring the chunk back into a known state as soon
as possible, evacuate all the valid data out of the line and let the
fw judge if the block can be written to in the next reset cycle.
Do this by introducing a new gc list for lines with failed writes,
and ensure that the rate limiter allocates a small portion of
the write bandwidth to get the job done.
The lba list is saved in memory for use during gc as we
cannot gurantee that the emeta data is readable if a write
error occurred.
Signed-off-by: Hans Holmberg <hans.holmberg@cnexlabs.com>
Reviewed-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <mb@lightnvm.io>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The write error recovery path is incomplete, so rework
the write error recovery handling to do resubmits directly
from the write buffer.
When a write error occurs, the remaining sectors in the chunk are
mapped out and invalidated and the request inserted in a resubmit list.
The writer thread checks if there are any requests to resubmit,
scans and invalidates any lbas that have been overwritten by later
writes and resubmits the failed entries.
Signed-off-by: Hans Holmberg <hans.holmberg@cnexlabs.com>
Reviewed-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <mb@lightnvm.io>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
(resend for properly queueing in patchwork)
kcm_clone() creates kernel socket, which does not take net counter.
Thus, the net may die before the socket is completely destructed,
i.e. kcm_exit_net() is executed before kcm_done().
Reported-by: syzbot+5f1a04e374a635efc426@syzkaller.appspotmail.com
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since header_preamble_size is 0 for SMB2+ we can remove it in those
code paths that are only invoked from SMB2.
Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
struct smb2_hdr is now just a wrapper for smb2_sync_hdr.
We can thus get rid of smb2_hdr completely and access the sync header directly.
Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Handle this additional status in the same way as SESSION_EXPIRED.
Signed-off-by: Mark Syms <mark.syms@citrix.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
CC: Stable <stable@vger.kernel.org>
Remove dead function for manual sync. I/O
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <mb@lightnvm.io>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
If the namespace is unregistered before the LightNVM target is removed
(e.g., on hot unplug) it is too late for the target to store any metadata
on the device - any attempt to write to the device will fail. In this
case, pass on a "gracefull teardown" flag to the target to let it know
when this happens.
In the case of pblk, we pad the open line (close all open chunks) to
improve data retention. In the event of an ungraceful shutdown, avoid
this part and just clean up.
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <mb@lightnvm.io>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Do the check for the chunk state after making sure that the chunk type
is supported.
Fixes: 32ef9412c1 ("lightnvm: pblk: implement get log report chunk")
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <mb@lightnvm.io>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Call nvm_submit_io directly and remove an unnecessary indirection on the
read path.
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <mb@lightnvm.io>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When cleaning up buffer entries as we wrap up, their state should be
"completed". If any of the entries is in "submitted" state, it means
that something bad has happened. Trigger a warning immediately instead of
waiting for the state flag to eventually be updated, thus hiding the
issue.
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <mb@lightnvm.io>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
In the event of a mismatch between the read LBA and the metadata pointer
reported by the device, improve the error message to be able to detect
the offending physical address (PPA) mapped to the corrupted LBA.
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <mb@lightnvm.io>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Check that the lba stored in the LBA metadata is correct in the GC path
too. This requires a new helper function to check random reads in the
vector read.
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <mb@lightnvm.io>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Bad blocks can grow at runtime. Check that the number of valid blocks in
a line are within the sanity threshold before allocating the line for
new writes.
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <mb@lightnvm.io>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
In the event of a line failing to allocate, fail gracefully and stop the
pipeline to avoid more write failing in the same place.
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <mb@lightnvm.io>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pull NVMe changes from Christoph:
"Below is another set of NVMe updates for 4.18. Besides the usual bug
fixes this includes more feature completness in terms of AEN and log
page handling on the target."
* 'nvme-4.18' of git://git.infradead.org/nvme:
nvme: use the changed namespaces list log to clear ns data changed AENs
nvme: mark nvme_queue_scan static
nvme: submit AEN event configuration on startup
nvmet: mask pending AENs
nvmet: add AEN configuration support
nvmet: implement the changed namespaces log
nvmet: split log page implementation
nvmet: add a new nvmet_zero_sgl helper
nvme.h: add AEN configuration symbols
nvme.h: add the changed namespace list log
nvme.h: untangle AEN notice definitions
nvmet: fix error return code in nvmet_file_ns_enable()
nvmet: fix a typo in nvmet_file_ns_enable()
nvme-fabrics: allow internal passthrough command on deleting controllers
nvme-loop: add support for multiple ports
nvme-pci: simplify __nvme_submit_cmd
nvme-pci: Rate limit the nvme timeout warnings
nvme: allow duplicate controller if prior controller being deleted
There is almost no shared logic, which leads to a very confusing code
flow.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Tested-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Both callers take just around so function call, so move it in.
Also remove the now pointless blk_mq_sched_init wrapper.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Tested-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Reported-by: Damien Le Moal <Damien.LeMoal@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Tested-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
These are only used by the block core. Also move the declarations to
block/blk.h.
Reported-by: Damien Le Moal <Damien.LeMoal@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Tested-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
No point in doing this in elevator_init.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reported-by: Damien Le Moal <Damien.LeMoal@wdc.com>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Tested-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Per section 5.2 we need to issue the corresponding log page to clear an
AEN, so for a namespace data changed AEN we need to read the changed
namespace list log. And once we read that log anyway we might as well
use it to optimize the rescan.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
And move it toward the top of the file to avoid a forward declaration.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
We should register for AEN events; some law-abiding targets might
not be sending us AENs otherwise.
Signed-off-by: Hannes Reinecke <hare@suse.com>
[hch: slight cleanups]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Per section 5.2 of the NVMe 1.3 spec:
"When the controller posts a completion queue entry for an outstanding
Asynchronous Event Request command and thus reports an asynchronous
event, subsequent events of that event type are automatically masked by
the controller until the host clears that event. An event is cleared by
reading the log page associated with that event using the Get Log Page
command (see section 5.14)."
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
AEN configuration via the 'Get Features' and 'Set Features' admin
command is mandatory, so we should be implemeting handling for it.
Signed-off-by: Hannes Reinecke <hare@suse.com>
[hch: use WRITE_ONCE, check for invalid values]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Daniel Verkamp <daniel.verkamp@intel.com>
Just keep a per-controller buffer of changed namespaces and copy it out
in the get log page implementation.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Daniel Verkamp <daniel.verkamp@intel.com>
Remove the common code to allocate a buffer and copy it into the SGL.
Instead the two no-op implementations just zero the SGL directly, and
the smart log allocates a buffer on its own. This prepares for the
more elaborate ANA log page.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Zeroes the SGL in the payload.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Hannes Reinecke <hare@suse.com>
[hch: split from a larger patch]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
This patch reorders the error cases in showing the XPS configuration so
that we hold off on memory allocation until after we have verified that we
can support XPS on a given ring.
Fixes: 184c449f91 ("net: Add support for XPS with QoS via traffic classes")
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous code was optimistic, accepting the offload of whole action
chain when there was a single known action (drop/redirect). This results
in offloading a rule which should not be offloaded, because its behavior
cannot be reproduced in the hardware.
For example:
$ tc filter add dev eno1 parent ffff: protocol ip \
u32 ht 800: order 1 match tcp src 42 FFFF \
action mirred egress mirror dev enp1s16 pipe \
drop
The controller is unable to mirror the packet to a VF, but still
offloads the rule by dropping the packet.
Change the approach of the function to a pessimistic one, rejecting the
chain when an unknown action is found. This is better suited for future
extensions.
Note that both recognized actions always return TC_ACT_SHOT, therefore
it is safe to ignore actions behind them.
Signed-off-by: Ondřej Hlavatý <ohlavaty@redhat.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
smb2_hdr is just a wrapper around smb2_sync_hdr at this stage
and smb2_hdr is going away.
Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
The two structures smb2_oplock_breaq_req/rsp are now basically identical.
Replace this with a single definition of a smb2_oplock_break structure.
Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Separate out all the 4 byte rfc1002 headers so that they are no longer
part of the SMB2 header structures to prepare for future work to add
compounding support.
Update the smb3 transform header processing that we no longer have
a rfc1002 header at the start of this structure.
Update smb2_readv_callback to accommodate that the first iovector in the
response is no the smb2 header and no longer a rfc1002 header.
Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
The server detects reconnect by the (non-zero) value in PreviousSessionId
of SMB2/SMB3 SessionSetup request, but this behavior regressed due
to commit 166cea4dc3
("SMB2: Separate RawNTLMSSP authentication from SMB2_sess_setup")
CC: Stable <stable@vger.kernel.org>
CC: Sachin Prabhu <sprabhu@redhat.com>
Signed-off-by: Steve French <smfrench@gmail.com>
Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com>
- Clear out i_mapping error state when we're reinitializing inodes.
-----BEGIN PGP SIGNATURE-----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=UtGb
-----END PGP SIGNATURE-----
Merge tag 'xfs-4.17-fixes-3' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux
Pull xfs fix from Darrick Wong:
"Clear out i_mapping error state when we're reinitializing inodes.
This last minute fix prevents writeback error state from persisting
past the end of the in-core inode lifecycle and causing EIO errors to
be reported to userspace when no error has occurred.
This fix for the behavioral regression has been soaking in for-next
for a while, but various fs developers persuaded me to try to get it
upstream for 4.17 because the patch that broke things was introduced
in 4.17-rc4"
* tag 'xfs-4.17-fixes-3' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
fs: clear writeback errors in inode_init_always
The current error handling code has an issue where it does:
if (priv->txchan)
cpdma_chan_destroy(priv->txchan);
The problem is that ->txchan is either valid or an error pointer (which
would lead to an Oops). I've changed it to use multiple error labels so
that the test can be removed.
Also there were some missing calls to netif_napi_del().
Fixes: 3ef0fdb234 ("net: davinci_emac: switch to new cpdma layer")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With CONFIG_CC_STACKPROTECTOR enabled the kernel panics as below when
parsing a NCSI_CMD_PKG_INFO command:
[ 150.149711] Kernel panic - not syncing: stack-protector: Kernel stack is corrupted in: 805cff08
[ 150.149711]
[ 150.159919] CPU: 0 PID: 1301 Comm: ncsi-netlink Not tainted 4.13.16-468cbec6d2c91239332cb91b1f0a73aafcb6f0c6 #1
[ 150.170004] Hardware name: Generic DT based system
[ 150.174852] [<80109930>] (unwind_backtrace) from [<80106bc4>] (show_stack+0x20/0x24)
[ 150.182641] [<80106bc4>] (show_stack) from [<805d36e4>] (dump_stack+0x20/0x28)
[ 150.189888] [<805d36e4>] (dump_stack) from [<801163ac>] (panic+0xdc/0x278)
[ 150.196780] [<801163ac>] (panic) from [<801162cc>] (__stack_chk_fail+0x20/0x24)
[ 150.204111] [<801162cc>] (__stack_chk_fail) from [<805cff08>] (ncsi_pkg_info_all_nl+0x244/0x258)
[ 150.212912] [<805cff08>] (ncsi_pkg_info_all_nl) from [<804f939c>] (genl_lock_dumpit+0x3c/0x54)
[ 150.221535] [<804f939c>] (genl_lock_dumpit) from [<804f873c>] (netlink_dump+0xf8/0x284)
[ 150.229550] [<804f873c>] (netlink_dump) from [<804f8d44>] (__netlink_dump_start+0x124/0x17c)
[ 150.237992] [<804f8d44>] (__netlink_dump_start) from [<804f9880>] (genl_rcv_msg+0x1c8/0x3d4)
[ 150.246440] [<804f9880>] (genl_rcv_msg) from [<804f9174>] (netlink_rcv_skb+0xd8/0x134)
[ 150.254361] [<804f9174>] (netlink_rcv_skb) from [<804f96a4>] (genl_rcv+0x30/0x44)
[ 150.261850] [<804f96a4>] (genl_rcv) from [<804f7790>] (netlink_unicast+0x198/0x234)
[ 150.269511] [<804f7790>] (netlink_unicast) from [<804f7ffc>] (netlink_sendmsg+0x368/0x3b0)
[ 150.277783] [<804f7ffc>] (netlink_sendmsg) from [<804abea4>] (sock_sendmsg+0x24/0x34)
[ 150.285625] [<804abea4>] (sock_sendmsg) from [<804ac1dc>] (___sys_sendmsg+0x244/0x260)
[ 150.293556] [<804ac1dc>] (___sys_sendmsg) from [<804ad98c>] (__sys_sendmsg+0x5c/0x9c)
[ 150.301400] [<804ad98c>] (__sys_sendmsg) from [<804ad9e4>] (SyS_sendmsg+0x18/0x1c)
[ 150.308984] [<804ad9e4>] (SyS_sendmsg) from [<80102640>] (ret_fast_syscall+0x0/0x3c)
[ 150.316743] ---[ end Kernel panic - not syncing: stack-protector: Kernel stack is corrupted in: 805cff08
This turns out to be because the attrs array in ncsi_pkg_info_all_nl()
is initialised to a length of NCSI_ATTR_MAX which is the maximum
attribute number, not the number of attributes.
Fixes: 955dc68cb9 ("net/ncsi: Add generic netlink family")
Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two last minute fixes, hopefully they make it to 4.17 still.
rt2x00
* revert a fix which caused even more problems
iwlwifi
* fix a crash when there are 16 or more logical CPUs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJbDq9KAAoJEG4XJFUm622bdFkIAIkIFEEC7TU3p5ud8YDUSOl/
6MBX/QFSTsFiyWL44YbH+0fU9vBla1oQuOtw+LFyr+te8OOLZzczdb30xUS+/tj0
O/LNMvNZ/TtvRl92Plj7ZcPmbDVa4UAABKL4ZKOjPP7EKdrCFQMLJ92IdHny+PW0
cwOwR5kmcTUgUHzHJ3D/g4M/TIz9UOgGFf1ET5+XiaYR9no84fQEXxDtBgMiNPvH
dCR8naiWliq3Zjyfc7nBSMKOk9bOlxRSUPQrjxYN/cLFZEzJJOIU8oSIacgvaYw9
DcZdwJn3BCOiWBihTPr5nzwsdvWOVNE2zc991IqqduhkkzcJdo0CPoTmnh604ZY=
=PSVv
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2018-05-30' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 4.17
Two last minute fixes, hopefully they make it to 4.17 still.
rt2x00
* revert a fix which caused even more problems
iwlwifi
* fix a crash when there are 16 or more logical CPUs
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When we fail to modify a rule, we incorrectly release the idr handle
of the unmodified old rule.
Fix that by checking if we need to release it.
Fixes: fe2502e49b ("net_sched: remove cls_flower idr on failure")
Reported-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With CONFIG_DMA_API_DEBUG=y, calling sonic_open() produces the
message, "DMA-API: device driver failed to check map error".
Add the missing dma_mapping_error() call.
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Acked-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes issues where color management properties don't persist
over DPMS on/off, or when the CRTC is moved across connectors.
Signed-off-by: Leo (Sunpeng) Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When the underscan state was changed, atomic-check was triggering a
validation but passing the old underscan values. This change adds a
somewhat hacky check in dm_update_crtcs_state that will update the
stream if old and newunderscan values are different.
This was causing 4k on Fiji to allow underscan when it wasn't permitted.
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
