There is a known bug on BCM2711's SDHCI core integration where the
controller will hang when the difference between the core clock and the
bus clock is too great. Specifically this can be reproduced under the
following conditions:
- No SD card plugged in, polling thread is running, probing cards at
100 kHz.
- BCM2711's core clock configured at 500MHz or more.
So set 200 kHz as the minimum clock frequency available for that board.
For more information on the issue see this:
https://lore.kernel.org/linux-mmc/20210322185816.27582-1-nsaenz@kernel.org/T/#m11f2783a09b581da6b8a15f302625b43a6ecdeca
Fixes: f84e411c85 ("mmc: sdhci-iproc: Add support for emmc2 of the BCM2711")
Signed-off-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/1628334401-6577-5-git-send-email-stefan.wahren@i2se.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If the card has not been power cycled, it may still be using 1.8V
signaling. This situation is detected in mmc_sd_init_card function and
should be handled in mmci stm32 variant. The host->pwr_reg variable is
also correctly protected with spin locks.
Fixes: 94b94a93e3 ("mmc: mmci_sdmmc: Implement signal voltage callbacks")
Signed-off-by: Christophe Kerello <christophe.kerello@foss.st.com>
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210701143353.13188-1-yann.gautier@foss.st.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When a Data CRC interrupt is received, the driver disables the DMA, then
sends the stop/abort command and then waits for Data Transfer Over.
However, sometimes, when a data CRC error is received in the middle of a
multi-block write transfer, the Data Transfer Over interrupt is never
received, and the driver hangs and never completes the request.
The driver sets the BMOD.SWR bit (SDMMC_IDMAC_SWRESET) when stopping the
DMA, but according to the manual CMD.STOP_ABORT_CMD should be programmed
"before assertion of SWR". Do these operations in the recommended
order. With this change the Data Transfer Over is always received
correctly in my tests.
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210630102232.16011-1-vincent.whitchurch@axis.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
- Use kref to fix KASAN splats triggered during card removal
- Don't allocate IDA for OF aliases
-----BEGIN PGP SIGNATURE-----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=17QT
-----END PGP SIGNATURE-----
Merge tag 'mmc-v5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
- Use kref to fix KASAN splats triggered during card removal
- Don't allocate IDA for OF aliases
* tag 'mmc-v5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: core: Don't allocate IDA for OF aliases
mmc: core: Use kref in place of struct mmc_blk_data::usage
There's a chance that the IDA allocated in mmc_alloc_host() is not freed
for some time because it's freed as part of a class' release function
(see mmc_host_classdev_release() where the IDA is freed). If another
thread is holding a reference to the class, then only once all balancing
device_put() calls (in turn calling kobject_put()) have been made will
the IDA be released and usable again.
Normally this isn't a problem because the kobject is released before
anything else that may want to use the same number tries to again, but
with CONFIG_DEBUG_KOBJECT_RELEASE=y and OF aliases it becomes pretty
easy to try to allocate an alias from the IDA twice while the first time
it was allocated is still pending a call to ida_simple_remove(). It's
also possible to trigger it by using CONFIG_DEBUG_KOBJECT_RELEASE and
probe defering a driver at boot that calls mmc_alloc_host() before
trying to get resources that may defer likes clks or regulators.
Instead of allocating from the IDA in this scenario, let's just skip it
if we know this is an OF alias. The number is already "claimed" and
devices that aren't using OF aliases won't try to use the claimed
numbers anyway (see mmc_first_nonreserved_index()). This should avoid
any issues with mmc_alloc_host() returning failures from the
ida_simple_get() in the case that we're using an OF alias.
Cc: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Cc: Sujit Kautkar <sujitka@chromium.org>
Reported-by: Zubin Mithra <zsm@chromium.org>
Fixes: fa2d0aa969 ("mmc: core: Allow setting slot index via device tree alias")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20210623075002.1746924-3-swboyd@chromium.org
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Ulf reported the following KASAN splat after adding some manual hacks
into mmc-utils[1].
DEBUG: mmc_blk_open: Let's sleep for 10s..
mmc1: card 0007 removed
BUG: KASAN: use-after-free in mmc_blk_get+0x58/0xb8
Read of size 4 at addr ffff00000a394a28 by task mmc/180
CPU: 2 PID: 180 Comm: mmc Not tainted 5.10.0-rc4-00069-gcc758c8c7127-dirty #5
Hardware name: Qualcomm Technologies, Inc. APQ 8016 SBC (DT)
Call trace:
dump_backtrace+0x0/0x2b4
show_stack+0x18/0x6c
dump_stack+0xfc/0x168
print_address_description.constprop.0+0x6c/0x488
kasan_report+0x118/0x210
__asan_load4+0x94/0xd0
mmc_blk_get+0x58/0xb8
mmc_blk_open+0x7c/0xdc
__blkdev_get+0x3b4/0x964
blkdev_get+0x64/0x100
blkdev_open+0xe8/0x104
do_dentry_open+0x234/0x61c
vfs_open+0x54/0x64
path_openat+0xe04/0x1584
do_filp_open+0xe8/0x1e4
do_sys_openat2+0x120/0x230
__arm64_sys_openat+0xf0/0x15c
el0_svc_common.constprop.0+0xac/0x234
do_el0_svc+0x84/0xa0
el0_sync_handler+0x264/0x270
el0_sync+0x174/0x180
Allocated by task 33:
stack_trace_save+0x9c/0xdc
kasan_save_stack+0x28/0x60
__kasan_kmalloc.constprop.0+0xc8/0xf0
kasan_kmalloc+0x10/0x20
mmc_blk_alloc_req+0x94/0x4b0
mmc_blk_probe+0x2d4/0xaa4
mmc_bus_probe+0x34/0x4c
really_probe+0x148/0x6e0
driver_probe_device+0x78/0xec
__device_attach_driver+0x108/0x16c
bus_for_each_drv+0xf4/0x15c
__device_attach+0x168/0x240
device_initial_probe+0x14/0x20
bus_probe_device+0xec/0x100
device_add+0x55c/0xaf0
mmc_add_card+0x288/0x380
mmc_attach_sd+0x18c/0x22c
mmc_rescan+0x444/0x4f0
process_one_work+0x3b8/0x650
worker_thread+0xa0/0x724
kthread+0x218/0x220
ret_from_fork+0x10/0x38
Freed by task 33:
stack_trace_save+0x9c/0xdc
kasan_save_stack+0x28/0x60
kasan_set_track+0x28/0x40
kasan_set_free_info+0x24/0x4c
__kasan_slab_free+0x100/0x180
kasan_slab_free+0x14/0x20
kfree+0xb8/0x46c
mmc_blk_put+0xe4/0x11c
mmc_blk_remove_req.part.0+0x6c/0xe4
mmc_blk_remove+0x368/0x370
mmc_bus_remove+0x34/0x50
__device_release_driver+0x228/0x31c
device_release_driver+0x2c/0x44
bus_remove_device+0x1e4/0x200
device_del+0x2b0/0x770
mmc_remove_card+0xf0/0x150
mmc_sd_detect+0x9c/0x150
mmc_rescan+0x110/0x4f0
process_one_work+0x3b8/0x650
worker_thread+0xa0/0x724
kthread+0x218/0x220
ret_from_fork+0x10/0x38
The buggy address belongs to the object at ffff00000a394800
which belongs to the cache kmalloc-1k of size 1024
The buggy address is located 552 bytes inside of
1024-byte region [ffff00000a394800, ffff00000a394c00)
The buggy address belongs to the page:
page:00000000ff84ed53 refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x8a390
head:00000000ff84ed53 order:3 compound_mapcount:0 compound_pincount:0
flags: 0x3fffc0000010200(slab|head)
raw: 03fffc0000010200 dead000000000100 dead000000000122 ffff000009f03800
raw: 0000000000000000 0000000000100010 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff00000a394900: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
ffff00000a394980: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
>ffff00000a394a00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^
ffff00000a394a80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
ffff00000a394b00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
Looking closer at the problem, it looks like a classic dangling pointer
bug. The 'struct mmc_blk_data' that is used after being freed in
mmc_blk_put() is stashed away in 'md->disk->private_data' via
mmc_blk_alloc_req() but used in mmc_blk_get() because the 'usage' count
isn't properly aligned with the lifetime of the pointer. You'd expect
the 'usage' member to be in sync with the kfree(), and it mostly is,
except that mmc_blk_get() needs to dereference the potentially freed
memory storage for the 'struct mmc_blk_data' stashed away in the
private_data member to look at 'usage' before it actually figures out if
it wants to consider it a valid pointer or not. That's not going to work
if the freed memory has been overwritten by something else after the
free, and KASAN rightly complains here.
To fix the immediate problem, let's set the private_data member to NULL
in mmc_blk_put() so that mmc_blk_get() can consider the object "on the
way out" if the pointer is NULL and not even try to look at 'usage' if
the object isn't going to be around much longer. With that set to NULL
on the last mmc_blk_put(), optimize the get path further and use a kref
underneath the 'open_lock' mutex to only up the reference count if it's
non-zero, i.e. alive, and otherwise make mmc_blk_get() return NULL,
without actually testing the reference count if we're in the process of
removing the object from the system.
Finally, tighten the locking region on the put side to only be around
the parts that are removing the 'mmc_blk_data' from the system and
publishing that fact to the gendisk and then drop the lock as soon as we
can to avoid holding the lock around code that doesn't need it. This
fixes the KASAN issue.
Cc: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Cc: Sujit Kautkar <sujitka@chromium.org>
Cc: Zubin Mithra <zsm@chromium.org>
Reported-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/linux-mmc/CAPDyKFryT63Jc7+DXWSpAC19qpZRqFr1orxwYGMuSqx247O8cQ@mail.gmail.com/ [1]
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20210623075002.1746924-2-swboyd@chromium.org
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fix the following fallthrough warning (mips-randconfig with Clang):
drivers/mmc/host/jz4740_mmc.c:792:2: warning: unannotated fall-through between switch labels [-Wimplicit-fallthrough]
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/lkml/60edca25.k00ut905IFBjPyt5%25lkp@intel.com/
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
-----BEGIN PGP SIGNATURE-----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=gHse
-----END PGP SIGNATURE-----
Merge tag 'block-5.14-2021-07-08' of git://git.kernel.dk/linux-block
Pull more block updates from Jens Axboe:
"A combination of changes that ended up depending on both the driver
and core branch (and/or the IDE removal), and a few late arriving
fixes. In detail:
- Fix io ticks wrap-around issue (Chunguang)
- nvme-tcp sock locking fix (Maurizio)
- s390-dasd fixes (Kees, Christoph)
- blk_execute_rq polling support (Keith)
- blk-cgroup RCU iteration fix (Yu)
- nbd backend ID addition (Prasanna)
- Partition deletion fix (Yufen)
- Use blk_mq_alloc_disk for mmc, mtip32xx, ubd (Christoph)
- Removal of now dead block request types due to IDE removal
(Christoph)
- Loop probing and control device cleanups (Christoph)
- Device uevent fix (Christoph)
- Misc cleanups/fixes (Tetsuo, Christoph)"
* tag 'block-5.14-2021-07-08' of git://git.kernel.dk/linux-block: (34 commits)
blk-cgroup: prevent rcu_sched detected stalls warnings while iterating blkgs
block: fix the problem of io_ticks becoming smaller
nvme-tcp: can't set sk_user_data without write_lock
loop: remove unused variable in loop_set_status()
block: remove the bdgrab in blk_drop_partitions
block: grab a device refcount in disk_uevent
s390/dasd: Avoid field over-reading memcpy()
dasd: unexport dasd_set_target_state
block: check disk exist before trying to add partition
ubd: remove dead code in ubd_setup_common
nvme: use return value from blk_execute_rq()
block: return errors from blk_execute_rq()
nvme: use blk_execute_rq() for passthrough commands
block: support polling through blk_execute_rq
block: remove REQ_OP_SCSI_{IN,OUT}
block: mark blk_mq_init_queue_data static
loop: rewrite loop_exit using idr_for_each_entry
loop: split loop_lookup
loop: don't allow deleting an unspecified loop device
loop: move loop_ctl_mutex locking into loop_add
...
Here is the big set of tty and serial driver patches for 5.14-rc1.
A bit more than normal, but nothing major, lots of cleanups. Highlights
are:
- lots of tty api cleanups and mxser driver cleanups from Jiri
- build warning fixes
- various serial driver updates
- coding style cleanups
- various tty driver minor fixes and updates
- removal of broken and disable r3964 line discipline (finally!)
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYOM4qQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylKvQCfbh+OmTkDlDlDhSWlxuV05M1XTXoAoLUcLZru
s5JCnwSZztQQLMDHj7Pd
=Zupm
-----END PGP SIGNATURE-----
Merge tag 'tty-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial updates from Greg KH:
"Here is the big set of tty and serial driver patches for 5.14-rc1.
A bit more than normal, but nothing major, lots of cleanups.
Highlights are:
- lots of tty api cleanups and mxser driver cleanups from Jiri
- build warning fixes
- various serial driver updates
- coding style cleanups
- various tty driver minor fixes and updates
- removal of broken and disable r3964 line discipline (finally!)
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (227 commits)
serial: mvebu-uart: remove unused member nb from struct mvebu_uart
arm64: dts: marvell: armada-37xx: Fix reg for standard variant of UART
dt-bindings: mvebu-uart: fix documentation
serial: mvebu-uart: correctly calculate minimal possible baudrate
serial: mvebu-uart: do not allow changing baudrate when uartclk is not available
serial: mvebu-uart: fix calculation of clock divisor
tty: make linux/tty_flip.h self-contained
serial: Prefer unsigned int to bare use of unsigned
serial: 8250: 8250_omap: Fix possible interrupt storm on K3 SoCs
serial: qcom_geni_serial: use DT aliases according to DT bindings
Revert "tty: serial: Add UART driver for Cortina-Access platform"
tty: serial: Add UART driver for Cortina-Access platform
MAINTAINERS: add me back as mxser maintainer
mxser: Documentation, fix typos
mxser: Documentation, make the docs up-to-date
mxser: Documentation, remove traces of callout device
mxser: introduce mxser_16550A_or_MUST helper
mxser: rename flags to old_speed in mxser_set_serial_info
mxser: use port variable in mxser_set_serial_info
mxser: access info->MCR under info->slock
...
This KUnit update for Linux 5.14-rc1 consists of fixes and features:
-- add support for skipped tests
-- introduce kunit_kmalloc_array/kunit_kcalloc() helpers
-- add gnu_printf specifiers
-- add kunit_shutdown
-- add unit test for filtering suites by names
-- convert lib/test_list_sort.c to use KUnit
-- code organization moving default config to tools/testing/kunit
-- refactor of internal parser input handling
-- cleanups and updates to documentation
-- code cleanup related to casts
-----BEGIN PGP SIGNATURE-----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=5QAv
-----END PGP SIGNATURE-----
Merge tag 'linux-kselftest-kunit-fixes-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull KUnit update from Shuah Khan:
"Fixes and features:
- add support for skipped tests
- introduce kunit_kmalloc_array/kunit_kcalloc() helpers
- add gnu_printf specifiers
- add kunit_shutdown
- add unit test for filtering suites by names
- convert lib/test_list_sort.c to use KUnit
- code organization moving default config to tools/testing/kunit
- refactor of internal parser input handling
- cleanups and updates to documentation
- code cleanup related to casts"
* tag 'linux-kselftest-kunit-fixes-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest: (29 commits)
kunit: add unit test for filtering suites by names
kasan: test: make use of kunit_skip()
kunit: test: Add example tests which are always skipped
kunit: tool: Support skipped tests in kunit_tool
kunit: Support skipped tests
thunderbolt: test: Reinstate a few casts of bitfields
kunit: tool: internal refactor of parser input handling
lib/test: convert lib/test_list_sort.c to use KUnit
kunit: introduce kunit_kmalloc_array/kunit_kcalloc() helpers
kunit: Remove the unused all_tests.config
kunit: Move default config from arch/um -> tools/testing/kunit
kunit: arch/um/configs: Enable KUNIT_ALL_TESTS by default
kunit: Add gnu_printf specifiers
lib/cmdline_kunit: Remove a cast which are no-longer required
kernel/sysctl-test: Remove some casts which are no-longer required
thunderbolt: test: Remove some casts which are no longer required
mmc: sdhci-of-aspeed: Remove some unnecessary casts from KUnit tests
iio: Remove a cast in iio-test-format which is no longer required
device property: Remove some casts in property-entry-test
Documentation: kunit: Clean up some string casts in examples
...
When an eMMC device is being run in HS400 mode, any access to the
RPMB device will cause the error message "mmc1: Invalid UHS-I mode
selected". This happens as a result of tuning being disabled before
RPMB access and then re-enabled after the RPMB access is complete.
When tuning is re-enabled, the system has to switch from HS400
to HS200 to do the tuning and then back to HS400. As part of
sequence to switch from HS400 to HS200 the system is temporarily
put into HS mode. When switching to HS mode, sdhci_get_preset_value()
is called and does not have support for HS mode and prints the warning
message and returns the preset for SDR12. The fix is to add support
for MMC and SD HS modes to sdhci_get_preset_value().
This can be reproduced on any system running eMMC in HS400 mode
(not HS400ES) by using the "mmc" utility to run the following
command: "mmc rpmb read-counter /dev/mmcblk0rpmb".
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Fixes: 52983382c7 ("mmc: sdhci: enhance preset value function")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210624163045.33651-1-alcooperx@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
that's just a bunch of data so the diffstat reflects that. Looking beyond that
there's just a bunch of updates all around in various clk drivers. Renesas and
NXP (for i.MX) are two SoC vendors that have a lot of patches in here. Overall
the driver changes look to be mostly enabling more clks and non-critical fixes
that we could hold until the next merge window.
I'm especially excited about the series from Arnd that graduates clkdev to be
the only implementation of clk_get() and clk_put(). That's a good step in the
right direction to migreate eveerything over to the common clk framework. Now
we don't have to worry about clkdev specific details, they're just part of the
clk API now.
Core:
- clkdev is now the only option, i.e. clk_get()/clk_put() is implemented in
only one place in the kernel instead of in drivers/clk/clkdev.c and in
architectures that want their own implementation
New Drivers:
- Texas Instruments' LMK04832 Ultra Low-Noise JESD204B Compliant Clock
Jitter Cleaner With Dual Loop PLLs
- Qualcomm MDM9607 GCC
- Qualcomm SC8180X display clks
- Qualcomm SM6125 GCC
- Qualcomm SM8250 CAMCC (camera)
- Renesas RZ/G2L SoC
- Hisilicon hi3559A SoC
Updates:
- Stop using clock-output-names in ST clk drivers (yay!)
- Support secure mode of STM32MP1 SoCs
- Improve clock support for Actions S500 SoC
- duty cycle setting support on qcom clks
- Add TI am33xx spread spectrum clock support
- Use determine_rate() for the Amlogic pll ops instead of round_rate()
- Restrict Amlogic gp0/1 and audio plls range on g12a/sm1
- Improve Amlogic axg-audio controller error on deferral
- Add NNA clocks on Amlogic g12a
- Reduce memory footprint of Rockchip PLL rate tables
- A fix for the newly added Rockchip rk3568 clk driver
- Exported clock for the newly added Rockchip video decoder
- Remove audio ipg clock from i.MX8MP
- Remove deprecated legacy clock binding for i.MX SCU clock driver
- Use common clk-imx8qxp for both i.MX8QXP and i.MX8QM
- Add multiple clocks to clk-imx8qxp driver (enet, hdmi, lcdif, audio,
parallel interface)
- Add dedicated clock ops for i.MX paralel interface
- Different fixes for clocks controlled by ATF on i.MX SoCs
- Add A53/A72 frequency scaling support i.MX clk-scu driver
- Add special case for DCSS clock on suspend for i.MX clk-scu driver
- Add parent save/restore on suspend/resume to i.MX clk-scu driver
- Skip runtime PM enablement for CPU clocks in i.MX clk-scu driver
- Remove the sys1_pll/sys2_pll clock gates for i.MX8MQ and their
bindings
- Tegra clk driver no longer deasserts resets on clk_enable as it
gets in the way of certain power-up sequences
- Fix compile testing for Tegra clk driver
- One patch to fix a divider on the Allwinner v3s Audio PLL
- Add support for CPU core clock boost modes on Renesas R-Car Gen3
- Add ISPCS (Image Signal Processor) clocks on Renesas R-Car V3U
- Switch SH/R-Mobile and R-Car "DIV6" clocks to .determine_rate()
and improve support for multiple parents
- Switch Renesas RZ/N1 divider clocks to .determine_rate()
- Add ZA2 (Audio Clock Generator) clock on Renesas R-Car D3
- Convert ar7 to common clk framework
- Convert ralink to common clk framework
-----BEGIN PGP SIGNATURE-----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=YnCF
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"This round has a diffstat dominated by Qualcomm clk drivers. Honestly
though that's just a bunch of data so the diffstat reflects that.
Looking beyond that there's just a bunch of updates all around in
various clk drivers. Renesas and NXP (for i.MX) are two SoC vendors
that have a lot of patches in here.
Overall the driver changes look to be mostly enabling more clks and
non-critical fixes that we could hold until the next merge window.
I'm especially excited about the series from Arnd that graduates
clkdev to be the only implementation of clk_get() and clk_put().
That's a good step in the right direction to migreate eveerything over
to the common clk framework. Now we don't have to worry about clkdev
specific details, they're just part of the clk API now.
Core:
- clkdev is now the only option, i.e. clk_get()/clk_put() is
implemented in only one place in the kernel instead of in
drivers/clk/clkdev.c and in architectures that want their own
implementation
New Drivers:
- Texas Instruments' LMK04832 Ultra Low-Noise JESD204B Compliant
Clock Jitter Cleaner With Dual Loop PLLs
- Qualcomm MDM9607 GCC
- Qualcomm SC8180X display clks
- Qualcomm SM6125 GCC
- Qualcomm SM8250 CAMCC (camera)
- Renesas RZ/G2L SoC
- Hisilicon hi3559A SoC
Updates:
- Stop using clock-output-names in ST clk drivers (yay!)
- Support secure mode of STM32MP1 SoCs
- Improve clock support for Actions S500 SoC
- duty cycle setting support on qcom clks
- Add TI am33xx spread spectrum clock support
- Use determine_rate() for the Amlogic pll ops instead of
round_rate()
- Restrict Amlogic gp0/1 and audio plls range on g12a/sm1
- Improve Amlogic axg-audio controller error on deferral
- Add NNA clocks on Amlogic g12a
- Reduce memory footprint of Rockchip PLL rate tables
- A fix for the newly added Rockchip rk3568 clk driver
- Exported clock for the newly added Rockchip video decoder
- Remove audio ipg clock from i.MX8MP
- Remove deprecated legacy clock binding for i.MX SCU clock driver
- Use common clk-imx8qxp for both i.MX8QXP and i.MX8QM
- Add multiple clocks to clk-imx8qxp driver (enet, hdmi, lcdif,
audio, parallel interface)
- Add dedicated clock ops for i.MX paralel interface
- Different fixes for clocks controlled by ATF on i.MX SoCs
- Add A53/A72 frequency scaling support i.MX clk-scu driver
- Add special case for DCSS clock on suspend for i.MX clk-scu driver
- Add parent save/restore on suspend/resume to i.MX clk-scu driver
- Skip runtime PM enablement for CPU clocks in i.MX clk-scu driver
- Remove the sys1_pll/sys2_pll clock gates for i.MX8MQ and their
bindings
- Tegra clk driver no longer deasserts resets on clk_enable as it
gets in the way of certain power-up sequences
- Fix compile testing for Tegra clk driver
- One patch to fix a divider on the Allwinner v3s Audio PLL
- Add support for CPU core clock boost modes on Renesas R-Car Gen3
- Add ISPCS (Image Signal Processor) clocks on Renesas R-Car V3U
- Switch SH/R-Mobile and R-Car "DIV6" clocks to .determine_rate() and
improve support for multiple parents
- Switch Renesas RZ/N1 divider clocks to .determine_rate()
- Add ZA2 (Audio Clock Generator) clock on Renesas R-Car D3
- Convert ar7 to common clk framework
- Convert ralink to common clk framework"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (161 commits)
clk: zynqmp: Handle divider specific read only flag
clk: zynqmp: Use firmware specific mux clock flags
clk: zynqmp: Use firmware specific divider clock flags
clk: zynqmp: Use firmware specific common clock flags
clk: lmk04832: Use of match table
clk: lmk04832: Depend on SPI
clk: stm32mp1: new compatible for secure RCC support
dt-bindings: clock: stm32mp1 new compatible for secure rcc
dt-bindings: reset: add MCU HOLD BOOT ID for SCMI reset domains on stm32mp15
dt-bindings: reset: add IDs for SCMI reset domains on stm32mp15
dt-bindings: clock: add IDs for SCMI clocks on stm32mp15
reset: stm32mp1: remove stm32mp1 reset
clk: hisilicon: Add clock driver for hi3559A SoC
dt-bindings: Document the hi3559a clock bindings
clk: si5341: Add sysfs properties to allow checking/resetting device faults
clk: si5341: Add silabs,iovdd-33 property
clk: si5341: Add silabs,xaxb-ext-clk property
clk: si5341: Allow different output VDD_SEL values
clk: si5341: Update initialization magic
clk: si5341: Check for input clock presence and PLL lock on startup
...
Fix a let hunk from the blk_mq_alloc_disk conversion.
Fixes: 281ea6a5bfdc ("mmc: switch to blk_mq_alloc_disk")
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20210621080144.3655131-1-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Use the blk_mq_alloc_disk to allocate the request_queue and gendisk
together.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20210616053934.880951-3-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The gendisk already acquires a reference to the queue when add_disk
is called, which dropped on put_disk. So remove the superflous
extra refcounting.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20210616053934.880951-2-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When DMA-mapping of the bounce buffer fails, the driver tries to fall
back, but it leaves the allocated host->bounce_buffer although its
size is zero. Later on, the driver checks the use of bounce buffer
with host->bounce_buffer pointer, and it tries to use the buffer
incorrectly, resulting in Oops.
This patch clears the release the unused buffer and clears the
bounce_buffer pointer for addressing the problem.
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20210611101948.18972-1-tiwai@suse.de
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If clock-frequency property is set and it is not the same as the current
clock rate of clk_xin(base clock frequency), set clk_xin to use the
provided clock rate.
Signed-off-by: Rashmi A <rashmi.a@intel.com>
Reviewed-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Sai Krishna Potthuri <lakshmi.sai.krishna.potthuri@xilinx.com>
Link: https://lore.kernel.org/r/20210603182242.25733-2-rashmi.a@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It might be that something goes wrong during tuning so the MMC core will
immediately trigger a retune. In our case it was:
- we sent a tuning block
- there was an error so we need to send an abort cmd to the eMMC
- the abort cmd had a CRC error
- retune was set by the MMC core
This lead to a vicious circle causing a performance regression of 75%.
So, clear retuning flags before we enable retuning to start with a known
cleared state.
Reported-by Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Suggested-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Fixes: bd11e8bd03 ("mmc: core: Flag re-tuning is needed on CRC errors")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210624151616.38770-2-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
With KUnit's EXPECT macros no longer typechecking arguments as strictly,
get rid of a number of now unnecessary casts.
Signed-off-by: David Gow <davidgow@google.com>
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Add support for the legacy Arasan sdhci controller on the BCM7211 and
related SoC's. This includes adding a .shutdown callback to increase
the power savings during S5.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Link: https://lore.kernel.org/r/20210602192758.38735-2-alcooperx@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It has been reported that usage of memcpy() to/from an iomem mapping is invalid,
and a recent arm64 memcpy update [1] triggers a memory abort when dram-access-quirk
is used on the G12A/G12B platforms.
This adds a local sg_copy_to_buffer which makes usage of io versions of memcpy
when dram-access-quirk is enabled.
[1] 285133040e ("arm64: Import latest memcpy()/memmove() implementation")
Fixes: acdc8e71d9 ("mmc: meson-gx: add dram-access-quirk")
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Suggested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20210609150230.9291-1-narmstrong@baylibre.com
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add support for the variant on the JZ4775 SoC from Ingenic. Let's also
clarify that the drive clock selection and sample clock selection have been
supported since JZ4775, not X1000. So, support for these two functions has
been added for JZ4775 and JZ4780.
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Acked-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/1623329930-14387-3-git-send-email-zhouyanjie@wanyeetech.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Enable support for system wakeup, by setting the wakeup capability for the
slot corresponding to the SDIO card. Users need to enable the wakeup
through the sysfs interface.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Link: https://lore.kernel.org/r/1623326486-25275-1-git-send-email-haibo.chen@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
'mmc_abort_tuning()' made me think tuning gets completely aborted.
However, it sends only a STOP cmd to cancel the current tuning cmd.
Tuning process may still continue after that. So, rename the function to
'mmc_send_abort_tuning()' to better reflect all this.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20210608180620.40059-1-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The card timing and the bus frequency are not changed atomically with
respect to calls to the set_clock() callback in the driver. The result
is the driver sees a transient state where there's a mismatch between
the two and thus the inputs to the phase correction calculation
formula are garbage.
Switch from dev_warn() to dev_dbg() to avoid noise in the normal case,
though the change does make bad configurations less likely to be
noticed.
Reported-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20210607013020.85885-1-andrew@aj.id.au
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The sdhci_sprd_writew() was defined by never used in sdhci_ops:
drivers/mmc/host/sdhci-sprd.c:134:20: warning: unused function 'sdhci_sprd_writew'
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20210601095403.236007-2-krzysztof.kozlowski@canonical.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
While initializing an UHS-I SD card, the mmc core first tries to switch to
1.8V I/O voltage, before it continues to change the settings for the bus
speed mode.
However, the current behaviour in the mmc core is inconsistent and doesn't
conform to the SD spec. More precisely, an SD card that supports UHS-I must
set both the SD_OCR_CCS bit and the SD_OCR_S18R bit in the OCR register
response. When switching to 1.8V I/O the mmc core correctly checks both of
the bits, but only the SD_OCR_S18R bit when changing the settings for bus
speed mode.
Rather than actually fixing the code to confirm to the SD spec, let's
deliberately deviate from it by requiring only the SD_OCR_S18R bit for both
parts. This enables us to support UHS-I for SDSC cards (outside spec),
which is actually being supported by some existing SDSC cards. Moreover,
this fixes the inconsistent behaviour.
Signed-off-by: Christian Loehle <cloehle@hyperstone.com>
Link: https://lore.kernel.org/r/CWXP265MB26803AE79E0AD5ED083BF2A6C4529@CWXP265MB2680.GBRP265.PROD.OUTLOOK.COM
Cc: stable@vger.kernel.org
[Ulf: Rewrote commit message and comments to clarify the changes]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Since we don't use structure field layout randomization
the manual shuffling can affect some macros, in particular
container_of() against struct of_mmc_spi, which becomes
a no-op when pdata member is the first one in the structure.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210528112127.71738-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
dev_dbg() in any case prints the device and driver name, no need
to repeat this in (some) messages. Drop duplicates for good.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210528112127.71738-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As of commit 4cdc2ec1da ("mmc: dw_mmc: move rockchip related code
to a separate file"), dw_mmc-pltfm.c no longer uses the clock API.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Link: https://lore.kernel.org/r/20210527194226.1705607-1-geert@linux-m68k.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The hardware provides capability configuration registers for each SDHCI
in the global configuration space for the SD controller. Writes to the
global capability registers are mirrored to the capability registers in
the associated SDHCI. Configuration of the capabilities must be written
through the mirror registers prior to initialisation of the SDHCI.
Signed-off-by: Steven Lee <steven_lee@aspeedtech.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20210524073308.9328-5-steven_lee@aspeedtech.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The direction of the pipe argument must match the request-type direction
bit or control requests may fail depending on the host-controller-driver
implementation.
Fix the SET_ROM_WAIT_STATES request which erroneously used
usb_rcvctrlpipe().
Fixes: 88095e7b47 ("mmc: Add new VUB300 USB-to-SD/SDIO/MMC driver")
Cc: stable@vger.kernel.org # 3.0
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210521133026.17296-1-johan@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
use pm_runtime_resume_and_get() to replace pm_runtime_get_sync and
pm_runtime_put_noidle. this change is just to simplify the code, no
actual functional changes.
Signed-off-by: Tian Tao <tiantao6@hisilicon.com>
Link: https://lore.kernel.org/r/1621558965-34077-1-git-send-email-tiantao6@hisilicon.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
use pm_runtime_resume_and_get() to replace pm_runtime_get_sync and
pm_runtime_put_noidle. this change is just to simplify the code, no
actual functional changes.
Signed-off-by: Tian Tao <tiantao6@hisilicon.com>
Link: https://lore.kernel.org/r/1621558775-31185-1-git-send-email-tiantao6@hisilicon.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
use pm_runtime_resume_and_get() to replace pm_runtime_get_sync and
pm_runtime_put_noidle. this change is just to simplify the code, no
actual functional changes
Signed-off-by: Tian Tao <tiantao6@hisilicon.com>
Link: https://lore.kernel.org/r/1621513304-27824-1-git-send-email-tiantao6@hisilicon.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The same calculation to get transfer descriptor offset is already used
at 3 different locations. Let's create a new helper to simplify code.
Signed-off-by: Yue Hu <huyue2@yulong.com>
Link: https://lore.kernel.org/r/20210521034432.2321-1-zbestahu@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We already have 'mrq->data' before calling these two functions, no
need to find it again via 'mrq->data' internally. Also remove local
data variable accordingly.
Signed-off-by: Yue Hu <huyue2@yulong.com>
Link: https://lore.kernel.org/r/20210517100900.1620-1-zbestahu@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
On some boards the data strobe line isn't wired up, rendering HS400
support broken, even if both the controller and the eMMC claim to
support it. Allow to disable HS400 mode via DT.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Link: https://lore.kernel.org/r/20210510190400.105162-3-l.stach@pengutronix.de
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Instead of having an indirection through the SDHCI layer and emulating
a capability bit, that isn't there in hardware, do the same same thing
as with HS400_ES and advertise the support for HS400 directly through
the MMC caps.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Haibo Chen <haibo.chen@nxp.com>
Link: https://lore.kernel.org/r/20210510190400.105162-2-l.stach@pengutronix.de
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In SD spec v6.x the SD function extension registers for performance
enhancements were introduced. As a part of this an optional internal cache
on the SD card, can be used to improve performance.
The let the SD card use the cache, the host needs to enable it and manage
flushing of the cache, so let's add support for this.
Note that for an SD card supporting the cache it's mandatory for it, to
also support the poweroff notification feature. According to the SD spec,
if the cache has been enabled and a poweroff notification is sent to the
card, that implicitly also means that the card should flush its internal
cache. Therefore, dealing with cache flushing for REQ_OP_FLUSH block
requests is sufficient.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Link: https://lore.kernel.org/r/20210511101359.83521-1-ulf.hansson@linaro.org
