[ Upstream commit 9949e2efb5 ]
Bonding send_peer_notif was defined as u8. Since commit 07a4ddec3c
("bonding: add an option to specify a delay between peer notifications").
the bond->send_peer_notif will be num_peer_notif multiplied by
peer_notif_delay, which is u8 * u32. This would cause the send_peer_notif
overflow easily. e.g.
ip link add bond0 type bond mode 1 miimon 100 num_grat_arp 30 peer_notify_delay 1000
To fix the overflow, let's set the send_peer_notif to u32 and limit
peer_notif_delay to 300s.
Reported-by: Liang Li <liali@redhat.com>
Closes: https://bugzilla.redhat.com/show_bug.cgi?id=2090053
Fixes: 07a4ddec3c ("bonding: add an option to specify a delay between peer notifications")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5944b5abd8 ]
Currently, we use hard code number to verify if we are in the
arp_interval timeslice. But some user may want to reduce/extend
the verify timeslice. With the similar team option 'missed_max'
the uers could change that number based on their own environment.
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 9949e2efb5 ("bonding: fix send_peer_notif overflow")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 120a56b01b ]
On mt753x_cpu_port_enable() there's code that enables flooding for the CPU
port only. Since mt753x_cpu_port_enable() runs twice when both CPU ports
are enabled, port 6 becomes the only port to forward the frames to. But
port 5 is the active port, so no frames received from the user ports will
be forwarded to port 5 which breaks network connectivity.
Every bit of the BC_FFP, UNM_FFP, and UNU_FFP bits represents a port. Fix
this issue by setting the bit that corresponds to the CPU port without
overwriting the other bits.
Clear the bits beforehand only for the MT7531 switch. According to the
documents MT7621 Giga Switch Programming Guide v0.3 and MT7531 Reference
Manual for Development Board v1.0, after reset, the BC_FFP, UNM_FFP, and
UNU_FFP bits are set to 1 for MT7531, 0 for MT7530.
The commit 5e5502e012 ("net: dsa: mt7530: fix roaming from DSA user
ports") silently changed the method to set the bits on the MT7530_MFC.
Instead of clearing the relevant bits before mt7530_cpu_port_enable()
which runs under a for loop, the commit started doing it on
mt7530_cpu_port_enable().
Back then, this didn't really matter as only a single CPU port could be
used since the CPU port number was hardcoded. The driver was later changed
with commit 1f9a6abecf ("net: dsa: mt7530: get cpu-port via dp->cpu_dp
instead of constant") to retrieve the CPU port via dp->cpu_dp. With that,
this silent change became an issue for when using multiple CPU ports.
Fixes: 5e5502e012 ("net: dsa: mt7530: fix roaming from DSA user ports")
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7f54cc9772 ]
MT7988 shares a significant part of the setup function with MT7531.
Split-off those parts into a shared function which is going to be used
also by mt7988_setup.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 120a56b01b ("net: dsa: mt7530: fix network connectivity with multiple CPU ports")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 82b318983c ]
Since the DSA conversion from the ds->ports array into the dst->ports
list, the DSA API has encouraged driver writers, as well as the core
itself, to write inefficient code.
Currently, code that wants to filter by a specific type of port when
iterating, like {!unused, user, cpu, dsa}, uses the dsa_is_*_port helper.
Under the hood, this uses dsa_to_port which iterates again through
dst->ports. But the driver iterates through the port list already, so
the complexity is quadratic for the typical case of a single-switch
tree.
This patch introduces some iteration helpers where the iterator is
already a struct dsa_port *dp, so that the other variant of the
filtering functions, dsa_port_is_{unused,user,cpu_dsa}, can be used
directly on the iterator. This eliminates the second lookup.
These functions can be used both by the core and by drivers.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 120a56b01b ("net: dsa: mt7530: fix network connectivity with multiple CPU ports")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 71460c9ec5 ]
By default the VSC8501 and VSC8502 RGMII/GMII/MII RX_CLK output is
disabled. To allow packet forwarding towards the MAC it needs to be
enabled.
For other PHYs supported by this driver the clock output is enabled
by default.
Fixes: d316986331 ("net: phy: mscc: add support for VSC8502")
Signed-off-by: David Epping <david.epping@missinglinkelectronics.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bbb320bfe2 ]
Stop restricting the PCI search to a range of PCI domains fed to
pci_get_domain_bus_and_slot(). Instead, use for_each_pci_dev() and
look at all PCI domains in one pass.
On systems with more than 8 sockets, this avoids error messages like
"Information: Invalid level, Can't get TDP control information at
specified levels on cpu 480" from the intel speed select utility.
Fixes: aa2ddd2425 ("platform/x86: ISST: Use numa node id for cpu pci dev mapping")
Signed-off-by: Steve Wahl <steve.wahl@hpe.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230519160420.2588475-1-steve.wahl@hpe.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9a1aac8a96 ]
On a multiple package system using Sub-NUMA clustering, there is an issue
in mapping Linux CPU number to PUNIT PCI device when manufacturer decided
to reuse the PCI bus number across packages. Bus number can be reused as
long as they are in different domain or segment. In this case some CPU
will fail to find a PCI device to issue SST requests.
When bus numbers are reused across CPU packages, we are using proximity
information by matching CPU numa node id to PUNIT PCI device numa node
id. But on a package there can be only one PUNIT PCI device, but multiple
numa nodes (one for each sub cluster). So, the numa node ID of the PUNIT
PCI device can only match with one numa node id of CPUs in a sub cluster
in the package.
Since there can be only one PUNIT PCI device per package, if we match
with numa node id of any sub cluster in that package, we can use that
mapping for any CPU in that package. So, store the match information
in a per package data structure and return the information when there
is no match.
While here, use defines for max bus number instead of hardcoding.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Link: https://lore.kernel.org/r/20220629194817.2418240-1-srinivas.pandruvada@linux.intel.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Stable-dep-of: bbb320bfe2 ("platform/x86: ISST: Remove 8 socket limit")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1f893f57a3 ]
From one hand, mlx5 driver is allowing to probe PFs in parallel.
From the other hand, devcom, which is a share resource between PFs, is
registered without any lock. This might resulted in memory problems.
Hence, use the global mlx5_dev_list_lock in order to serialize devcom
registration.
Fixes: fadd59fc50 ("net/mlx5: Introduce inter-device communication mechanism")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8a6e75e5f5 ]
Devcom API is intended to be used between 2 devices only add this
implied assumption into the code and check when it's no true.
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Maor Gottlieb <maorg@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Stable-dep-of: 691c041bf2 ("net/mlx5e: Fix deadlock in tc route query code")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b34ffb0c6d ]
The LRU and LRU_PERCPU maps allocate a new element on update before locking the
target hash table bucket. Right after that the maps try to lock the bucket.
If this fails, then maps return -EBUSY to the caller without releasing the
allocated element. This makes the element untracked: it doesn't belong to
either of free lists, and it doesn't belong to the hash table, so can't be
re-used; this eventually leads to the permanent -ENOMEM on LRU map updates,
which is unexpected. Fix this by returning the element to the local free list
if bucket locking fails.
Fixes: 20b6cc34ea ("bpf: Avoid hashtab deadlock with map_locked")
Signed-off-by: Anton Protopopov <aspsk@isovalent.com>
Link: https://lore.kernel.org/r/20230522154558.2166815-1-aspsk@isovalent.com
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 77c2a3097d ]
The bq24192 model relies on external charger-type detection and once
that is done the bq24190_charger code will update the input current.
In this case, when the initial power_supply_changed() call is made
from the interrupt handler, the input settings are 5V/0.5A which
on many devices is not enough power to charge (while the device is on).
On many devices the fuel-gauge relies in its external_power_changed
callback to timely signal userspace about charging <-> discharging
status changes. Add a power_supply_changed() call after updating
the input current. This allows the fuel-gauge driver to timely recheck
if the battery is charging after the new input current has been applied
and then it can immediately notify userspace about this.
Fixes: 18f8e6f695 ("power: supply: bq24190_charger: Get input_current_limit from our supplier")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2220af8ca6 ]
Some (USB) charger ICs have variants with USB D+ and D- pins to do their
own builtin charger-type detection, like e.g. the bq24190 and bq25890 and
also variants which lack this functionality, e.g. the bq24192 and bq25892.
In case the charger-type; and thus the input-current-limit detection is
done outside the charger IC then we need some way to communicate this to
the charger IC. In the past extcon was used for this, but if the external
detection does e.g. full USB PD negotiation then the extcon cable-types do
not convey enough information.
For these setups it was decided to model the external charging "brick"
and the parameters negotiated with it as a power_supply class-device
itself; and power_supply_set_input_current_limit_from_supplier() was
introduced to allow drivers to get the input-current-limit this way.
But in some cases psy drivers may want to know other properties, e.g. the
bq25892 can do "quick-charge" negotiation by pulsing its current draw,
but this should only be done if the usb_type psy-property of its supplier
is set to DCP (and device-properties indicate the board allows higher
voltages).
Instead of adding extra helper functions for each property which
a psy-driver wants to query from its supplier, refactor
power_supply_set_input_current_limit_from_supplier() into a
more generic power_supply_get_property_from_supplier() function.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Stable-dep-of: 77c2a3097d ("power: supply: bq24190: Call power_supply_changed() after updating input current")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 59a99cd462 ]
bq27xxx_external_power_changed() gets called when the charger is plugged
in or out. Rather then immediately scheduling an update wait 0.5 seconds
for things to stabilize, so that e.g. the (dis)charge current is stable
when bq27xxx_battery_update() runs.
Fixes: 740b755a3b ("bq27x00: Poll battery state")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 939a116142 ]
On gauges where the current register is signed, there is no charging
flag in the flags register. So only checking flags will not result
in power_supply_changed() getting called when e.g. a charger is plugged
in and the current sign changes from negative (discharging) to
positive (charging).
This causes userspace's notion of the status to lag until userspace
does a poll.
And when a power_supply_leds.c LED trigger is used to indicate charging
status with a LED, this LED will lag until the capacity percentage
changes, which may take many minutes (because the LED trigger only is
updated on power_supply_changed() calls).
Fix this by calling bq27xxx_battery_current_and_status() on gauges with
a signed current register and checking if the status has changed.
Fixes: 297a533b3e ("bq27x00: Cache battery registers")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ff4c4a2a44 ]
Move the bq27xxx_battery_update() functions to below
the bq27xxx_battery_current_and_status() function.
This is just moving a block of text, no functional changes.
This is a preparation patch for making bq27xxx_battery_update() check
the status and have it call power_supply_changed() on status changes.
Fixes: 297a533b3e ("bq27x00: Cache battery registers")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 68fdbe090c ]
When the Capacity Inaccurate flag is set, the chip still provides data
about the battery, albeit inaccurate. Instead of discarding capacity
values for CI=1, expose the stale data and use the
POWER_SUPPLY_HEALTH_CALIBRATION_REQUIRED property to indicate that the
values should be used with care.
Reviewed-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Sicelo A. Mhlongo <absicsz@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Stable-dep-of: ff4c4a2a44 ("power: supply: bq27xxx: Move bq27xxx_battery_update() down")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 57fb54ab9f upstream.
The mscc driver implements support for VSC8502, so its ID should be in
the MODULE_DEVICE_TABLE for automatic loading.
Signed-off-by: David Epping <david.epping@missinglinkelectronics.com>
Fixes: d316986331 ("net: phy: mscc: add support for VSC8502")
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 640bf95b2c upstream.
Should tc589_config() fail, some resources need to be released as already
done in the remove function.
Fixes: 15b99ac172 ("[PATCH] pcmcia: add return value to _config() functions")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/d8593ae867b24c79063646e36f9b18b0790107cb.1684575975.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a511637502 upstream.
Add hardware version read check for PMIC MT6359
Signed-off-by: Sen Chu <sen.chu@mediatek.com
Fixes: 4cfc965475 ("regulator: mt6359: Add support for MT6359P regulator")
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com
Link: https://lore.kernel.org/r/20230518040646.8730-1-sen.chu@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 111a833dc5 upstream.
The transmit buffers allocated by the driver can be used to transmit data
by any messages/commands needing the buffer. However, it is not guaranteed
to have been zero-ed before every new transmission and hence it will just
contain residual value from the previous transmission. There are several
reserved fields in the memory descriptors that must be zero(MBZ). The
receiver can reject the transmission if any such MBZ fields are non-zero.
While we can set the whole page to zero, it is not optimal as most of the
fields get initialised to the value required for the current transmission.
So, just set the reserved/MBZ fields to zero in the memory descriptors
explicitly to honour the requirement and keep the receiver happy.
Fixes: cc2195fe53 ("firmware: arm_ffa: Add support for MEM_* interfaces")
Reported-by: Marc Bonnici <marc.bonnici@arm.com>
Link: https://lore.kernel.org/r/20230503131252.12585-1-sudeep.holla@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f161cea5a2 upstream.
While testing the ethernet interface on a Variscite symphony carrier
board using an imx8mn SOM with an onboard ADIN1300 PHY (EC hardware
configuration), the ethernet PHY is not detected.
The ADIN1300 datasheet indicate that the "Management interface
active (t4)" state is reached at most 5ms after the reset signal is
deasserted.
The device tree in Variscite custom git repository uses the following
property:
phy-reset-post-delay = <20>;
Add a new MDIO property 'reset-deassert-us' of 20ms to have the same
delay inside the ethphy node. Adding this property fixes the problem
with the PHY detection.
Note that this SOM can also have an Atheros AR8033 PHY. In this case,
a 1ms deassert delay is sufficient. Add a comment to that effect.
Fixes: ade0176dd8 ("arm64: dts: imx8mn-var-som: Add Variscite VAR-SOM-MX8MN System on Module")
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit af87194352 upstream.
In case devcom allocation is failed, mlx5 is always freeing the priv.
However, this priv might have been allocated by a different thread,
and freeing it might lead to use-after-free bugs.
Fix it by freeing the priv only in case it was allocated by the
running thread.
Fixes: fadd59fc50 ("net/mlx5: Introduce inter-device communication mechanism")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c7dd225bc2 upstream.
SW Steering uses RC QP for writing STEs to ICM. This writingis done in LB
(loopback), and FL (force-loopback) QP is preferred for performance. FL is
available when RoCE is enabled or disabled based on RoCE caps.
This patch adds reading of FL capability from HCA caps in addition to the
existing reading from RoCE caps, thus fixing the case where we didn't
have loopback enabled when RoCE was disabled.
Fixes: 7304d603a5 ("net/mlx5: DR, Add support for force-loopback QP")
Signed-off-by: Itamar Gozlan <igozlan@nvidia.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1e5daf5565 upstream.
When calculating crc for hash index we use the function crc32 that
calculates for little-endian (LE) arch.
Then we convert it to network endianness using htonl(), but it's wrong
to do the conversion in BE archs since the crc32 value is already LE.
The solution is to switch the bytes from the crc result for all types
of arc.
Fixes: 40416d8ede ("net/mlx5: DR, Replace CRC32 implementation to use kernel lib")
Signed-off-by: Erez Shitrit <erezsh@nvidia.com>
Reviewed-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit afbed3f748 upstream.
NAPI gets called with budget of 0 from netpoll, which has interrupts
disabled. We should try to free some space on Tx rings and nothing
else.
Specifically do not try to handle XDP TX or try to refill Rx buffers -
we can't use the page pool from IRQ context. Don't check if IRQs moved,
either, that makes no sense in netpoll. Netpoll calls _all_ the rings
from whatever CPU it happens to be invoked on.
In general do as little as possible, the work quickly adds up when
there's tens of rings to poll.
The immediate stack trace I was seeing is:
__do_softirq+0xd1/0x2c0
__local_bh_enable_ip+0xc7/0x120
</IRQ>
<TASK>
page_pool_put_defragged_page+0x267/0x320
mlx5e_free_xdpsq_desc+0x99/0xd0
mlx5e_poll_xdpsq_cq+0x138/0x3b0
mlx5e_napi_poll+0xc3/0x8b0
netpoll_poll_dev+0xce/0x150
AFAIU page pool takes a BH lock, releases it and since BH is now
enabled tries to run softirqs.
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Fixes: 60bbf7eeef ("mlx5: use page_pool for xdp_return_frame call")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 95e4b25192 upstream.
The sscanf() function never returns negatives. It returns the number of
items successfully read.
Fixes: 1a218d312e ("platform/mellanox: mlxbf-pmc: Add Mellanox BlueField PMC driver")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/4ccdfd28-099b-40bf-8d77-ad4ea2e76b93@kili.mountain
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5b17a4971d upstream.
If an error occures after calling nv_mgmt_acquire_sema(), it should be
undone with a corresponding nv_mgmt_release_sema() call.
Add it in the error handling path of the probe as already done in the
remove function.
Fixes: cac1c52c36 ("forcedeth: mgmt unit interface")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Zhu Yanjun <zyjzyj2000@gmail.com>
Link: https://lore.kernel.org/r/355e9a7d351b32ad897251b6f81b5886fcdc6766.1684571393.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6ca328e985 upstream.
When doing plpmtu probe, the probe size is growing every time when it
receives the ACK during the Search state until the probe fails. When
the failure occurs, pl.probe_high is set and it goes to the Complete
state.
However, if the link pmtu is huge, like 65535 in loopback_dev, the probe
eventually keeps using SCTP_MAX_PLPMTU as the probe size and never fails.
Because of that, pl.probe_high can not be set, and the plpmtu probe can
never go to the Complete state.
Fix it by setting pl.probe_high to SCTP_MAX_PLPMTU when the probe size
grows to SCTP_MAX_PLPMTU in sctp_transport_pl_recv(). Also, not allow
the probe size greater than SCTP_MAX_PLPMTU in the Complete state.
Fixes: b87641aff9 ("sctp: do state transition when a probe succeeds on HB ACK recv path")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9510965747 upstream.
Constant 'C4_CHANNEL' does not exist on the firmware side. Value 0xC is
reserved for 'C7_1' instead.
Fixes: 04afbbbb1c ("ASoC: Intel: Skylake: Update the topology interface structure")
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20230519201711.4073845-4-amadeuszx.slawinski@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2e4be0d011 upstream.
The commit e335bb51cc ("x86/unwind: Ensure stack pointer is aligned")
tried to align the stack pointer in show_trace_log_lvl(), otherwise the
"stack < stack_info.end" check can't guarantee that the last read does
not go past the end of the stack.
However, we have the same problem with the initial value of the stack
pointer, it can also be unaligned. So without this patch this trivial
kernel module
#include <linux/module.h>
static int init(void)
{
asm volatile("sub $0x4,%rsp");
dump_stack();
asm volatile("add $0x4,%rsp");
return -EAGAIN;
}
module_init(init);
MODULE_LICENSE("GPL");
crashes the kernel.
Fixes: e335bb51cc ("x86/unwind: Ensure stack pointer is aligned")
Signed-off-by: Vernon Lovejoy <vlovejoy@redhat.com>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Link: https://lore.kernel.org/r/20230512104232.GA10227@redhat.com
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8fafac202d upstream.
In the pvcalls_new_active_socket() function, most error paths call
pvcalls_back_release_active(fedata->dev, fedata, map) which calls
sock_release() on "sock". The bug is that the caller also frees sock.
Fix this by making every error path in pvcalls_new_active_socket()
release the sock, and don't free it in the caller.
Fixes: 5db4d286a8 ("xen/pvcalls: implement connect command")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/e5f98dc2-0305-491f-a860-71bbd1398a2f@kili.mountain
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f67bc15e52 upstream.
This code generates a Smatch warning:
drivers/hwtracing/coresight/coresight-tmc-etr.c:947 tmc_etr_buf_insert_barrier_packet()
error: uninitialized symbol 'bufp'.
The problem is that if tmc_sg_table_get_data() returns -EINVAL, then
when we test if "len < CORESIGHT_BARRIER_PKT_SIZE", the negative "len"
value is type promoted to a high unsigned long value which is greater
than CORESIGHT_BARRIER_PKT_SIZE. Fix this bug by adding an explicit
check for error codes.
Fixes: 75f4e3619f ("coresight: tmc-etr: Add transparent buffer management")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/7d33e244-d8b9-4c27-9653-883a13534b01@kili.mountain
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f15afbd34d upstream.
Shifting signed 32-bit value by 31 bits is undefined, so changing
significant bit to unsigned. It was spotted by UBSAN.
So let's just fix this by using the BIT() helper for all SB_* flags.
Fixes: e462ec50cb ("VFS: Differentiate mount flags (MS_*) from internal superblock flags")
Signed-off-by: Hao Ge <gehao@kylinos.cn>
Message-Id: <20230424051835.374204-1-gehao@kylinos.cn>
[brauner@kernel.org: use BIT() for all SB_* flags]
Signed-off-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 19b8766459 upstream.
Each physical partition can provide multiple services each with UUID.
Each such service can be presented as logical partition with a unique
combination of VM ID and UUID. The number of distinct UUID in a system
will be less than or equal to the number of logical partitions.
However, currently it fails to register more than one logical partition
or service within a physical partition as the device name contains only
VM ID while both VM ID and UUID are maintained in the partition information.
The kernel complains with the below message:
| sysfs: cannot create duplicate filename '/devices/arm-ffa-8001'
| CPU: 1 PID: 1 Comm: swapper/0 Not tainted 6.3.0-rc7 #8
| Hardware name: FVP Base RevC (DT)
| Call trace:
| dump_backtrace+0xf8/0x118
| show_stack+0x18/0x24
| dump_stack_lvl+0x50/0x68
| dump_stack+0x18/0x24
| sysfs_create_dir_ns+0xe0/0x13c
| kobject_add_internal+0x220/0x3d4
| kobject_add+0x94/0x100
| device_add+0x144/0x5d8
| device_register+0x20/0x30
| ffa_device_register+0x88/0xd8
| ffa_setup_partitions+0x108/0x1b8
| ffa_init+0x2ec/0x3a4
| do_one_initcall+0xcc/0x240
| do_initcall_level+0x8c/0xac
| do_initcalls+0x54/0x94
| do_basic_setup+0x1c/0x28
| kernel_init_freeable+0x100/0x16c
| kernel_init+0x20/0x1a0
| ret_from_fork+0x10/0x20
| kobject_add_internal failed for arm-ffa-8001 with -EEXIST, don't try to
| register things with the same name in the same directory.
| arm_ffa arm-ffa: unable to register device arm-ffa-8001 err=-17
| ARM FF-A: ffa_setup_partitions: failed to register partition ID 0x8001
By virtue of being random enough to avoid collisions when generated in a
distributed system, there is no way to compress UUID keys to the number
of bits required to identify each. We can eliminate '-' in the name but
it is not worth eliminating 4 bytes and add unnecessary logic for doing
that. Also v1.0 doesn't provide the UUID of the partitions which makes
it hard to use the same for the device name.
So to keep it simple, let us alloc an ID using ida_alloc() and append the
same to "arm-ffa" to make up a unique device name. Also stash the id value
in ffa_dev to help freeing the ID later when the device is destroyed.
Fixes: e781858488 ("firmware: arm_ffa: Add initial FFA bus support for device enumeration")
Reported-by: Lucian Paul-Trifu <lucian.paul-trifu@arm.com>
Link: https://lore.kernel.org/r/20230419-ffa_fixes_6-4-v2-3-d9108e43a176@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b2f2a3c980 upstream.
CHARGE_INHIBITED bit position of the ChargerStatus register is actually
0 not 1. This patch corrects it.
Fixes: feb583e37f ("power: supply: add sbs-charger driver")
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 35092c5819 upstream.
Add a cache parameter to bq27xxx_battery_current_and_status() so that
it can optionally use cached flags instead of re-reading them itself.
This is a preparation patch for making bq27xxx_battery_update() check
the status and have it call power_supply_changed() on status changes.
Fixes: 297a533b3e ("bq27x00: Cache battery registers")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c00bc80462 upstream.
Before this patch bq27xxx_battery_teardown() was setting poll_interval = 0
to avoid bq27xxx_battery_update() requeuing the delayed_work item.
There are 2 problems with this:
1. If the driver is unbound through sysfs, rather then the module being
rmmod-ed, this changes poll_interval unexpectedly
2. This is racy, after it being set poll_interval could be changed
before bq27xxx_battery_update() checks it through
/sys/module/bq27xxx_battery/parameters/poll_interval
Fix this by added a removed attribute to struct bq27xxx_device_info and
using that instead of setting poll_interval to 0.
There also is another poll_interval related race on remove(), writing
/sys/module/bq27xxx_battery/parameters/poll_interval will requeue
the delayed_work item for all devices on the bq27xxx_battery_devices
list and the device being removed was only removed from that list
after cancelling the delayed_work item.
Fix this by moving the removal from the bq27xxx_battery_devices list
to before cancelling the delayed_work item.
Fixes: 8cfaaa8118 ("bq27x00_battery: Fix OOPS caused by unregistring bq27x00 driver")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 444ff00734 upstream.
devm_request_threaded_irq() requested IRQs are only free-ed after
the driver's remove function has ran. So the IRQ could trigger and
call bq27xxx_battery_update() after bq27xxx_battery_teardown() has
already run.
Switch to explicitly free-ing the IRQ in bq27xxx_battery_i2c_remove()
to fix this.
Fixes: 8807feb91b ("power: bq27xxx_battery: Add interrupt handling support")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5c34c0aef1 upstream.
bq27xxx_battery_update() assumes / requires that it is only run once,
not multiple times at the same time. But there are 3 possible callers:
1. bq27xxx_battery_poll() delayed_work item handler
2. bq27xxx_battery_irq_handler_thread() I2C IRQ handler
3. bq27xxx_battery_setup()
And there is no protection against these racing with each other,
fix this race condition by making all callers take di->lock:
- Rename bq27xxx_battery_update() to bq27xxx_battery_update_unlocked()
- Add new bq27xxx_battery_update() which takes di->lock and then calls
bq27xxx_battery_update_unlocked()
- Make stale cache check code in bq27xxx_battery_get_property(), which
already takes di->lock directly to check the jiffies, call
bq27xxx_battery_update_unlocked() instead of messing with
the delayed_work item
- Make bq27xxx_battery_update_unlocked() mod the delayed-work item
so that the next poll is delayed to poll_interval milliseconds after
the last update independent of the source of the update
Fixes: 740b755a3b ("bq27x00: Poll battery state")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e448464399 upstream.
When a battery's status changes from charging to full then
the charging-blink-full-solid trigger tries to change
the LED from blinking to solid/on.
As is documented in include/linux/leds.h to deactivate blinking /
to make the LED solid a LED_OFF must be send:
"""
* Deactivate blinking again when the brightness is set to LED_OFF
* via the brightness_set() callback.
"""
led_set_brighness() calls with a brightness value other then 0 / LED_OFF
merely change the brightness of the LED in its on state while it is
blinking.
So power_supply_update_bat_leds() must first send a LED_OFF event
before the LED_FULL to disable blinking.
Fixes: 6501f728c5 ("power_supply: Add new LED trigger charging-blink-solid-full")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cb8b02fd63 upstream.
There are two ways that special characters (not allowed in some
other operating systems like Windows, but allowed in POSIX) have
been mapped in the past ("SFU" and "SFM" mappings) to allow them
to be stored in a range reserved for special chars. The default
for Linux has been to use "mapposix" (ie the SFM mapping) but
the conversion to the new mount API in the 5.11 kernel broke
the ability to override the default mapping of the reserved
characters (like '?' and '*' and '\') via "mapchars" mount option.
This patch fixes that - so can now mount with "mapchars"
mount option to override the default ("mapposix" ie SFM) mapping.
Reported-by: Tyler Spivey <tspivey8@gmail.com>
Fixes: 24e0a1eff9 ("cifs: switch to new mount api")
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 878ecb0897 upstream.
optlen is fetched without checking whether there is more than one byte to parse.
It can lead to out-of-bounds access.
Found by InfoTeCS on behalf of Linux Verification Center
(linuxtesting.org) with SVACE.
Fixes: c61a404325 ("[IPV6]: Find option offset by type.")
Signed-off-by: Gavrilov Ilia <Ilia.Gavrilov@infotecs.ru>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
