On the Loongson-2G/2H/3A/3B there is a hardware flaw that ll/sc and
lld/scd is very weak ordering. We should add sync instructions "before
each ll/lld" and "at the branch-target between ll/sc" to workaround.
Otherwise, this flaw will cause deadlock occasionally (e.g. when doing
heavy load test with LTP).
Below is the explaination of CPU designer:
"For Loongson 3 family, when a memory access instruction (load, store,
or prefetch)'s executing occurs between the execution of LL and SC, the
success or failure of SC is not predictable. Although programmer would
not insert memory access instructions between LL and SC, the memory
instructions before LL in program-order, may dynamically executed
between the execution of LL/SC, so a memory fence (SYNC) is needed
before LL/LLD to avoid this situation.
Since Loongson-3A R2 (3A2000), we have improved our hardware design to
handle this case. But we later deduce a rarely circumstance that some
speculatively executed memory instructions due to branch misprediction
between LL/SC still fall into the above case, so a memory fence (SYNC)
at branch-target (if its target is not between LL/SC) is needed for
Loongson 3A1000, 3B1500, 3A2000 and 3A3000.
Our processor is continually evolving and we aim to to remove all these
workaround-SYNCs around LL/SC for new-come processor."
Here is an example:
Both cpu1 and cpu2 simutaneously run atomic_add by 1 on same atomic var,
this bug cause both 'sc' run by two cpus (in atomic_add) succeed at same
time('sc' return 1), and the variable is only *added by 1*, sometimes,
which is wrong and unacceptable(it should be added by 2).
Why disable fix-loongson3-llsc in compiler?
Because compiler fix will cause problems in kernel's __ex_table section.
This patch fix all the cases in kernel, but:
+. the fix at the end of futex_atomic_cmpxchg_inatomic is for branch-target
of 'bne', there other cases which smp_mb__before_llsc() and smp_llsc_mb() fix
the ll and branch-target coincidently such as atomic_sub_if_positive/
cmpxchg/xchg, just like this one.
+. Loongson 3 does support CONFIG_EDAC_ATOMIC_SCRUB, so no need to touch
edac.h
+. local_ops and cmpxchg_local should not be affected by this bug since
only the owner can write.
+. mips_atomic_set for syscall.c is deprecated and rarely used, just let
it go
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Huang Pei <huangpei@loongson.cn>
[paul.burton@mips.com:
- Simplify the addition of -mno-fix-loongson3-llsc to cflags, and add
a comment describing why it's there.
- Make loongson_llsc_mb() a no-op when
CONFIG_CPU_LOONGSON3_WORKAROUNDS=n, rather than a compiler memory
barrier.
- Add a comment describing the bug & how loongson_llsc_mb() helps
in asm/barrier.h.]
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: ambrosehua@gmail.com
Cc: Steven J . Hill <Steven.Hill@cavium.com>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Cc: Li Xuefeng <lixuefeng@loongson.cn>
Cc: Xu Chenghua <xuchenghua@loongson.cn>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Burton <paul.burton@mips.com>
Cc: James Hogan <jhogan@kernel.org>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: linux-mips@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Paul Burton <paul.burton@mips.com>
dma_sync_phys() is only called for some CPUs when a mapping is removed.
Add ARCH_HAS_SYNC_DMA_FOR_CPU only for the CPUs listed in
cpu_needs_post_dma_flush() which need this extra call and do not compile
this code in for other CPUs. We need this for R10000, R12000, BMIPS5000
CPUs and CPUs supporting MAAR which was introduced in MIPS32r5.
This will hopefully improve the performance of the not affected devices.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: ralf@linux-mips.org
Cc: jhogan@kernel.org
Cc: linux-mips@vger.kernel.org
Cc: nbd@nbd.name
Nobody has actually used the type (VERIFY_READ vs VERIFY_WRITE) argument
of the user address range verification function since we got rid of the
old racy i386-only code to walk page tables by hand.
It existed because the original 80386 would not honor the write protect
bit when in kernel mode, so you had to do COW by hand before doing any
user access. But we haven't supported that in a long time, and these
days the 'type' argument is a purely historical artifact.
A discussion about extending 'user_access_begin()' to do the range
checking resulted this patch, because there is no way we're going to
move the old VERIFY_xyz interface to that model. And it's best done at
the end of the merge window when I've done most of my merges, so let's
just get this done once and for all.
This patch was mostly done with a sed-script, with manual fix-ups for
the cases that weren't of the trivial 'access_ok(VERIFY_xyz' form.
There were a couple of notable cases:
- csky still had the old "verify_area()" name as an alias.
- the iter_iov code had magical hardcoded knowledge of the actual
values of VERIFY_{READ,WRITE} (not that they mattered, since nothing
really used it)
- microblaze used the type argument for a debug printout
but other than those oddities this should be a total no-op patch.
I tried to fix up all architectures, did fairly extensive grepping for
access_ok() uses, and the changes are trivial, but I may have missed
something. Any missed conversion should be trivially fixable, though.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull networking updates from David Miller:
1) New ipset extensions for matching on destination MAC addresses, from
Stefano Brivio.
2) Add ipv4 ttl and tos, plus ipv6 flow label and hop limit offloads to
nfp driver. From Stefano Brivio.
3) Implement GRO for plain UDP sockets, from Paolo Abeni.
4) Lots of work from Michał Mirosław to eliminate the VLAN_TAG_PRESENT
bit so that we could support the entire vlan_tci value.
5) Rework the IPSEC policy lookups to better optimize more usecases,
from Florian Westphal.
6) Infrastructure changes eliminating direct manipulation of SKB lists
wherever possible, and to always use the appropriate SKB list
helpers. This work is still ongoing...
7) Lots of PHY driver and state machine improvements and
simplifications, from Heiner Kallweit.
8) Various TSO deferral refinements, from Eric Dumazet.
9) Add ntuple filter support to aquantia driver, from Dmitry Bogdanov.
10) Batch dropping of XDP packets in tuntap, from Jason Wang.
11) Lots of cleanups and improvements to the r8169 driver from Heiner
Kallweit, including support for ->xmit_more. This driver has been
getting some much needed love since he started working on it.
12) Lots of new forwarding selftests from Petr Machata.
13) Enable VXLAN learning in mlxsw driver, from Ido Schimmel.
14) Packed ring support for virtio, from Tiwei Bie.
15) Add new Aquantia AQtion USB driver, from Dmitry Bezrukov.
16) Add XDP support to dpaa2-eth driver, from Ioana Ciocoi Radulescu.
17) Implement coalescing on TCP backlog queue, from Eric Dumazet.
18) Implement carrier change in tun driver, from Nicolas Dichtel.
19) Support msg_zerocopy in UDP, from Willem de Bruijn.
20) Significantly improve garbage collection of neighbor objects when
the table has many PERMANENT entries, from David Ahern.
21) Remove egdev usage from nfp and mlx5, and remove the facility
completely from the tree as it no longer has any users. From Oz
Shlomo and others.
22) Add a NETDEV_PRE_CHANGEADDR so that drivers can veto the change and
therefore abort the operation before the commit phase (which is the
NETDEV_CHANGEADDR event). From Petr Machata.
23) Add indirect call wrappers to avoid retpoline overhead, and use them
in the GRO code paths. From Paolo Abeni.
24) Add support for netlink FDB get operations, from Roopa Prabhu.
25) Support bloom filter in mlxsw driver, from Nir Dotan.
26) Add SKB extension infrastructure. This consolidates the handling of
the auxiliary SKB data used by IPSEC and bridge netfilter, and is
designed to support the needs to MPTCP which could be integrated in
the future.
27) Lots of XDP TX optimizations in mlx5 from Tariq Toukan.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1845 commits)
net: dccp: fix kernel crash on module load
drivers/net: appletalk/cops: remove redundant if statement and mask
bnx2x: Fix NULL pointer dereference in bnx2x_del_all_vlans() on some hw
net/net_namespace: Check the return value of register_pernet_subsys()
net/netlink_compat: Fix a missing check of nla_parse_nested
ieee802154: lowpan_header_create check must check daddr
net/mlx4_core: drop useless LIST_HEAD
mlxsw: spectrum: drop useless LIST_HEAD
net/mlx5e: drop useless LIST_HEAD
iptunnel: Set tun_flags in the iptunnel_metadata_reply from src
net/mlx5e: fix semicolon.cocci warnings
staging: octeon: fix build failure with XFRM enabled
net: Revert recent Spectre-v1 patches.
can: af_can: Fix Spectre v1 vulnerability
packet: validate address length if non-zero
nfc: af_nfc: Fix Spectre v1 vulnerability
phonet: af_phonet: Fix Spectre v1 vulnerability
net: core: Fix Spectre v1 vulnerability
net: minor cleanup in skb_ext_add()
net: drop the unused helper skb_ext_get()
...
include:
- Syscall tables & definitions for unistd.h are now generated by
scripts, providing greater consistency with other architectures &
making it easier to add new syscalls.
- Support for building kernels with no floating point support, upon
which any userland attempting to use floating point instructions will
receive a SIGILL. Mostly useful to shrink the kernel & as preparation
for nanoMIPS support which does not yet include FP.
- MIPS SIMD Architecture (MSA) vector register context is now exposed
by ptrace via a new NT_MIPS_MSA regset.
- ASIDs are now stored as 64b values even for MIPS32 kernels, expanding
the ASID version field sufficiently that we don't need to worry about
overflow & avoiding rare issues with reused ASIDs that have been
observed in the wild.
- The branch delay slot "emulation" page is now mapped without write
permission for the user, preventing its use as a nice location for
attacks to execute malicious code from.
- Support for ioremap_prot(), primarily to allow gdb or other
ptrace users the ability to view their tracee's memory using the same
cache coherency attribute.
- Optimizations to more cpu_has_* macros, allowing more to be
compile-time constant where possible.
- Enable building the whole kernel with UBSAN instrumentation.
- Enable building the kernel with link-time dead code & data
elimination.
Platform specific changes include:
- The Boston board gains a workaround for DMA prefetching issues with
the EG20T Platform Controller Hub that it uses.
- Cleanups to Cavium Octeon code removing about 20k lines of redundant
code, mostly unused or duplicate register definitions in headers.
- defconfig updates for the DECstation machines, including new
defconfigs for r4k & 64b machines.
- Further work on Loongson 3 support.
- DMA fixes for SiByte machines.
-----BEGIN PGP SIGNATURE-----
iIsEABYIADMWIQRgLjeFAZEXQzy86/s+p5+stXUA3QUCXB+vwBUccGF1bC5idXJ0
b25AbWlwcy5jb20ACgkQPqefrLV1AN3/EgD9Givei//X2oTd4w8HSe/uPeVkMnbA
93WMi1cS0EogAaUA/R7poLSnAE74mt+DT4PrGdQezUbXts9vUF/7VX0MvFIF
=hmtJ
-----END PGP SIGNATURE-----
Merge tag 'mips_4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS updates from Paul Burton:
"Here's the main MIPS pull for Linux 4.21. Core architecture changes
include:
- Syscall tables & definitions for unistd.h are now generated by
scripts, providing greater consistency with other architectures &
making it easier to add new syscalls.
- Support for building kernels with no floating point support, upon
which any userland attempting to use floating point instructions
will receive a SIGILL. Mostly useful to shrink the kernel & as
preparation for nanoMIPS support which does not yet include FP.
- MIPS SIMD Architecture (MSA) vector register context is now exposed
by ptrace via a new NT_MIPS_MSA regset.
- ASIDs are now stored as 64b values even for MIPS32 kernels,
expanding the ASID version field sufficiently that we don't need to
worry about overflow & avoiding rare issues with reused ASIDs that
have been observed in the wild.
- The branch delay slot "emulation" page is now mapped without write
permission for the user, preventing its use as a nice location for
attacks to execute malicious code from.
- Support for ioremap_prot(), primarily to allow gdb or other ptrace
users the ability to view their tracee's memory using the same
cache coherency attribute.
- Optimizations to more cpu_has_* macros, allowing more to be
compile-time constant where possible.
- Enable building the whole kernel with UBSAN instrumentation.
- Enable building the kernel with link-time dead code & data
elimination.
Platform specific changes include:
- The Boston board gains a workaround for DMA prefetching issues with
the EG20T Platform Controller Hub that it uses.
- Cleanups to Cavium Octeon code removing about 20k lines of
redundant code, mostly unused or duplicate register definitions in
headers.
- defconfig updates for the DECstation machines, including new
defconfigs for r4k & 64b machines.
- Further work on Loongson 3 support.
- DMA fixes for SiByte machines"
* tag 'mips_4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (95 commits)
MIPS: math-emu: Write-protect delay slot emulation pages
MIPS: Remove struct mm_context_t fp_mode_switching field
mips: generate uapi header and system call table files
mips: add system call table generation support
mips: remove syscall table entries
mips: add +1 to __NR_syscalls in uapi header
mips: rename scall64-64.S to scall64-n64.S
mips: remove unused macros
mips: add __NR_syscalls along with __NR_Linux_syscalls
MIPS: Expand MIPS32 ASIDs to 64 bits
MIPS: OCTEON: delete redundant register definitions
MIPS: OCTEON: cvmx_gmxx_inf_mode: use oldest forward compatible definition
MIPS: OCTEON: cvmx_mio_fus_dat3: use oldest forward compatible definition
MIPS: OCTEON: cvmx_pko_mem_debug8: use oldest forward compatible definition
MIPS: OCTEON: octeon-usb: use common gpio_bit definition
MIPS: OCTEON: enable all OCTEON drivers in defconfig
mips: annotate implicit fall throughs
MIPS: Hardcode cpu_has_mips* where target ISA allows
MIPS: MT: Remove norps command line parameter
MIPS: Only include mmzone.h when CONFIG_NEED_MULTIPLE_NODES=y
...
Jitting of BPF_K is supported already, but not BPF_X. This patch complete
the support for the latter on both MIPS and microMIPS.
Cc: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org
Acked-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
ASIDs have always been stored as unsigned longs, ie. 32 bits on MIPS32
kernels. This is problematic because it is feasible for the ASID version
to overflow & wrap around to zero.
We currently attempt to handle this overflow by simply setting the ASID
version to 1, using asid_first_version(), but we make no attempt to
account for the fact that there may be mm_structs with stale ASIDs that
have versions which we now reuse due to the overflow & wrap around.
Encountering this requires that:
1) A struct mm_struct X is active on CPU A using ASID (V,n).
2) That mm is not used on CPU A for the length of time that it takes
for CPU A's asid_cache to overflow & wrap around to the same
version V that the mm had in step 1. During this time tasks using
the mm could either be sleeping or only scheduled on other CPUs.
3) Some other mm Y becomes active on CPU A and is allocated the same
ASID (V,n).
4) mm X now becomes active on CPU A again, and now incorrectly has the
same ASID as mm Y.
Where struct mm_struct ASIDs are represented above in the format
(version, EntryHi.ASID), and on a typical MIPS32 system version will be
24 bits wide & EntryHi.ASID will be 8 bits wide.
The length of time required in step 2 is highly dependent upon the CPU &
workload, but for a hypothetical 2GHz CPU running a workload which
generates a new ASID every 10000 cycles this period is around 248 days.
Due to this long period of time & the fact that tasks need to be
scheduled in just the right (or wrong, depending upon your inclination)
way, this is obviously a difficult bug to encounter but it's entirely
possible as evidenced by reports.
In order to fix this, simply extend ASIDs to 64 bits even on MIPS32
builds. This will extend the period of time required for the
hypothetical system above to encounter the problem from 28 days to
around 3 trillion years, which feels safely outside of the realms of
possibility.
The cost of this is slightly more generated code in some commonly
executed paths, but this is pretty minimal:
| Code Size Gain | Percentage
-----------------------|----------------|-------------
decstation_defconfig | +270 | +0.00%
32r2el_defconfig | +652 | +0.01%
32r6el_defconfig | +1000 | +0.01%
I have been unable to measure any change in performance of the LMbench
lat_ctx or lat_proc tests resulting from the 64b ASIDs on either
32r2el_defconfig+interAptiv or 32r6el_defconfig+I6500 systems.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Suggested-by: James Hogan <jhogan@kernel.org>
References: https://lore.kernel.org/linux-mips/80B78A8B8FEE6145A87579E8435D78C30205D5F3@fzex.ruijie.com.cn/
References: https://lore.kernel.org/linux-mips/1488684260-18867-1-git-send-email-jiwei.sun@windriver.com/
Cc: Jiwei Sun <jiwei.sun@windriver.com>
Cc: Yu Huabing <yhb@ruijie.com.cn>
Cc: stable@vger.kernel.org # 2.6.12+
Cc: linux-mips@vger.kernel.org
There is a plan to build the kernel with -Wimplicit-fallthrough and
these places in the code produced warnings. Fix them up.
This patch produces no change in behaviour, but should be reviewed in
case these are actually bugs not intentional fallthoughs.
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Kees Cook <keescook@google.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
For multi-node Loongson-3 (NUMA configuration), r4k_blast_scache() can
only flush Node-0's scache. So we add r4k_blast_scache_node() by using
(CAC_BASE | (node_id << NODE_ADDRSPACE_SHIFT)) instead of CKSEG0 as the
start address.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
[paul.burton@mips.com: Include asm/mmzone.h from asm/r4kcache.h for
nid_to_addrbase(). Add asm/mach-generic/mmzone.h
to allow inclusion for all platforms.]
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/21129/
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <james.hogan@mips.com>
Cc: Steven J . Hill <Steven.Hill@cavium.com>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Cc: <stable@vger.kernel.org> # 3.15+
Fix a MIPS `dma_alloc_coherent' regression from commit bc3ec75de5
("dma-mapping: merge direct and noncoherent ops") that causes a cached
allocation to be returned on noncoherent cache systems.
This is due to an inverted check now used in the MIPS implementation of
`arch_dma_alloc' on the result from `dma_direct_alloc_pages' before
doing the cached-to-uncached mapping of the allocation address obtained.
The mapping has to be done for a non-NULL rather than NULL result,
because a NULL result means the allocation has failed.
Invert the check for correct operation then.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Fixes: bc3ec75de5 ("dma-mapping: merge direct and noncoherent ops")
Patchwork: https://patchwork.linux-mips.org/patch/20965/
Move remaining definitions and declarations from include/linux/bootmem.h
into include/linux/memblock.h and remove the redundant header.
The includes were replaced with the semantic patch below and then
semi-automated removal of duplicated '#include <linux/memblock.h>
@@
@@
- #include <linux/bootmem.h>
+ #include <linux/memblock.h>
[sfr@canb.auug.org.au: dma-direct: fix up for the removal of linux/bootmem.h]
Link: http://lkml.kernel.org/r/20181002185342.133d1680@canb.auug.org.au
[sfr@canb.auug.org.au: powerpc: fix up for removal of linux/bootmem.h]
Link: http://lkml.kernel.org/r/20181005161406.73ef8727@canb.auug.org.au
[sfr@canb.auug.org.au: x86/kaslr, ACPI/NUMA: fix for linux/bootmem.h removal]
Link: http://lkml.kernel.org/r/20181008190341.5e396491@canb.auug.org.au
Link: http://lkml.kernel.org/r/1536927045-23536-30-git-send-email-rppt@linux.vnet.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Serge Semin <fancer.lancer@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The alloc_bootmem_low_pages() function allocates PAGE_SIZE aligned regions
from low memory. memblock_alloc_low() with alignment set to PAGE_SIZE does
exactly the same thing.
The conversion is done using the following semantic patch:
@@
expression e;
@@
- alloc_bootmem_low_pages(e)
+ memblock_alloc_low(e, PAGE_SIZE)
Link: http://lkml.kernel.org/r/1536927045-23536-19-git-send-email-rppt@linux.vnet.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Serge Semin <fancer.lancer@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- kexec support for the generic MIPS platform when running on a CPU
including the MIPS Coherence Manager & related hardware.
- Improvements to the definition of memory barriers used around MMIO
accesses, and fixes in their use.
- Switch to CONFIG_NO_BOOTMEM from Mike Rapoport, finally dropping
reliance on the old bootmem code.
- A number of fixes & improvements for Loongson 3 systems.
- DT & config updates for the Microsemi Ocelot platform.
- Workaround to enable USB power on the Netgear WNDR3400v3.
- Various cleanups & fixes.
-----BEGIN PGP SIGNATURE-----
iIsEABYIADMWIQRgLjeFAZEXQzy86/s+p5+stXUA3QUCW9NfwRUccGF1bC5idXJ0
b25AbWlwcy5jb20ACgkQPqefrLV1AN1LNgD9Hy73DkYnnYeLNLcCe+5QMCr+NO2C
kwIs7kAI40X+/LQA/RgCcg6z4rUSH38hfNEobD6VXva7QiFhiYcJj5rCFH8O
=nDQg
-----END PGP SIGNATURE-----
Merge tag 'mips_4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS updates from Paul Burton:
- kexec support for the generic MIPS platform when running on a CPU
including the MIPS Coherence Manager & related hardware.
- Improvements to the definition of memory barriers used around MMIO
accesses, and fixes in their use.
- Switch to CONFIG_NO_BOOTMEM from Mike Rapoport, finally dropping
reliance on the old bootmem code.
- A number of fixes & improvements for Loongson 3 systems.
- DT & config updates for the Microsemi Ocelot platform.
- Workaround to enable USB power on the Netgear WNDR3400v3.
- Various cleanups & fixes.
* tag 'mips_4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (51 commits)
MIPS: Cleanup DSP ASE detection
MIPS: dts: Change upper case to lower case
MIPS: generic: Add Network, SPI and I2C to ocelot_defconfig
MIPS: Loongson-3: Fix BRIDGE irq delivery problem
MIPS: Loongson-3: Fix CPU UART irq delivery problem
MIPS: Remove unused PREF, PREFE & PREFX macros
MIPS: lib: Use kernel_pref & user_pref in memcpy()
MIPS: Remove unused CAT macro
MIPS: Add kernel_pref & user_pref helpers
MIPS: Remove unused TTABLE macro
MIPS: Remove unused PIC macros
MIPS: Remove unused MOVN & MOVZ macros
MIPS: Provide actually relaxed MMIO accessors
MIPS: Enforce strong ordering for MMIO accessors
MIPS: Correct `mmiowb' barrier for `wbflush' platforms
MIPS: Define MMIO ordering barriers
MIPS: mscc: add PCB120 to the ocelot fitImage
MIPS: mscc: add DT for Ocelot PCB120
MIPS: memset: Limit excessive `noreorder' assembly mode use
MIPS: memset: Fix CPU_DADDI_WORKAROUNDS `small_fixup' regression
...
gcc 3.3 has been retired for a while, use PTRS_PER_PGD and remove the
asm-offsets.h inclusion.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/20814/
Cc: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
The only functional differences (modulo a few missing fixes in the arch
code) is that architectures without coherent caches need a hook to
convert a virtual or dma address into a pfn, given that we don't have
the kernel linear mapping available for the otherwise easy virt_to_page
call. As a side effect we can support mmap of the per-device coherent
area even on architectures not providing the callback, and we make
previous dangerous default methods dma_common_mmap actually save for
non-coherent architectures by rejecting it without the right helper.
In addition to that we need a hook so that some architectures can
override the protection bits when mmaping a dma coherent allocations.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Paul Burton <paul.burton@mips.com> # MIPS parts
All the cache maintainance is already stubbed out when not enabled,
but merging the two allows us to nicely handle the case where
cache maintainance is required for some devices, but not others.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Paul Burton <paul.burton@mips.com> # MIPS parts
Various architectures support both coherent and non-coherent dma on a
per-device basis. Move the dma_noncoherent flag from the mips archdata
field to struct device proper to prepare the infrastructure for reuse on
other architectures.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Paul Burton <paul.burton@mips.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While both option select a form of conditional dma coherence they don't
actually share any code in the implementation, so untangle them.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Paul Burton <paul.burton@mips.com>
- Fix microMIPS build failures by adding a .insn directive to the
barrier_before_unreachable() asm statement in order to convince the
toolchain that the asm statement is a valid branch target rather
than a bogus attempt to switch ISA.
- Clean up our declarations of TLB functions that we overwrite with
generated code in order to prevent the compiler making assumptions
about alignment that cause microMIPS kernels built with GCC 7 &
above to die early during boot.
- Fix up a regression for MIPS32 kernels which slipped into the main
MIPS pull for 4.19, causing CONFIG_32BIT=y kernels to contain
inappropriate MIPS64 instructions.
- Extend our existing workaround for MIPSr6 builds that end up using
the __multi3 intrinsic to GCC 7 & below, rather than just GCC 7.
-----BEGIN PGP SIGNATURE-----
iIsEABYIADMWIQRgLjeFAZEXQzy86/s+p5+stXUA3QUCW37wVhUccGF1bC5idXJ0
b25AbWlwcy5jb20ACgkQPqefrLV1AN18iAD/ZO02rgkTgMG7NvZMtbOwflxe1aVz
YpAQzcOSz+CBxgUA/30ZwZm37hgMi3YWOJMSfmbuWKsYi+/vkcjwlfai7UUF
=oJFy
-----END PGP SIGNATURE-----
Merge tag 'mips_4.19_2' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS fixes from Paul Burton:
- Fix microMIPS build failures by adding a .insn directive to the
barrier_before_unreachable() asm statement in order to convince the
toolchain that the asm statement is a valid branch target rather
than a bogus attempt to switch ISA.
- Clean up our declarations of TLB functions that we overwrite with
generated code in order to prevent the compiler making assumptions
about alignment that cause microMIPS kernels built with GCC 7 &
above to die early during boot.
- Fix up a regression for MIPS32 kernels which slipped into the main
MIPS pull for 4.19, causing CONFIG_32BIT=y kernels to contain
inappropriate MIPS64 instructions.
- Extend our existing workaround for MIPSr6 builds that end up using
the __multi3 intrinsic to GCC 7 & below, rather than just GCC 7.
* tag 'mips_4.19_2' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
MIPS: lib: Provide MIPS64r6 __multi3() for GCC < 7
MIPS: Workaround GCC __builtin_unreachable reordering bug
compiler.h: Allow arch-specific asm/compiler.h
MIPS: Avoid move psuedo-instruction whilst using MIPS_ISA_LEVEL
MIPS: Consistently declare TLB functions
MIPS: Export tlbmiss_handler_setup_pgd near its definition
Use new return type vm_fault_t for fault handler. For now, this is just
documenting that the function returns a VM_FAULT value rather than an
errno. Once all instances are converted, vm_fault_t will become a
distinct type.
Ref-> commit 1c8f422059 ("mm: change return type to vm_fault_t")
In this patch all the caller of handle_mm_fault() are changed to return
vm_fault_t type.
Link: http://lkml.kernel.org/r/20180617084810.GA6730@jordon-HP-15-Notebook-PC
Signed-off-by: Souptick Joarder <jrdr.linux@gmail.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Michal Simek <monstr@monstr.eu>
Cc: James Hogan <jhogan@kernel.org>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: James E.J. Bottomley <jejb@parisc-linux.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: David S. Miller <davem@davemloft.net>
Cc: Richard Weinberger <richard@nod.at>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: "Levin, Alexander (Sasha Levin)" <alexander.levin@verizon.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
An overview of the general architecture changes:
- Massive DMA ops refactoring from Christoph Hellwig (huzzah for
deleting crufty code!).
- We introduce NT_MIPS_DSP & NT_MIPS_FP_MODE ELF notes & corresponding
regsets to expose DSP ASE & floating point mode state respectively,
both for live debugging & core dumps.
- We better optimize our code by hard-coding cpu_has_* macros at
compile time where their values are known due to the ISA revision
that the kernel build is targeting.
- The EJTAG exception handler now better handles SMP systems, where it
was previously possible for CPUs to clobber a register value saved
by another CPU.
- Our implementation of memset() gained a couple of fixes for MIPSr6
systems to return correct values in some cases where stores fault.
- We now implement ioremap_wc() using the uncached-accelerated cache
coherency attribute where supported, which is detected during boot,
and fall back to plain uncached access where necessary. The
MIPS-specific (and unused in tree) ioremap_uncached_accelerated() &
ioremap_cacheable_cow() are removed.
- The prctl(PR_SET_FP_MODE, ...) syscall is better supported for SMP
systems by reworking the way we ensure remote CPUs that may be
running threads within the affected process switch mode.
- Systems using the MIPS Coherence Manager will now set the
MIPS_IC_SNOOPS_REMOTE flag to avoid some unnecessary cache
maintenance overhead when flushing the icache.
- A few fixes were made for building with clang/LLVM, which
now sucessfully builds kernels for many of our platforms.
- Miscellaneous cleanups all over.
And some platform-specific changes:
- ar7 gained stubs for a few clock API functions to fix build failures
for some drivers.
- ath79 gained support for a few new SoCs, a few fixes & better
gpio-keys support.
- Ci20 now exposes its SPI bus using the spi-gpio driver.
- The generic platform can now auto-detect a suitable value for
PHYS_OFFSET based upon the memory map described by the device tree,
allowing us to avoid wasting memory on page book-keeping for systems
where RAM starts at a non-zero physical address.
- Ingenic systems using the jz4740 platform code now link their
vmlinuz higher to allow for kernels of a realistic size.
- Loongson32 now builds the kernel targeting MIPSr1 rather than MIPSr2
to avoid CPU errata.
- Loongson64 gains a couple of fixes, a workaround for a write
buffering issue & support for the Loongson 3A R3.1 CPU.
- Malta now uses the piix4-poweroff driver to handle powering down.
- Microsemi Ocelot gained support for its SPI bus & NOR flash, its
second MDIO bus and can now be supported by a FIT/.itb image.
- Octeon saw a bunch of header cleanups which remove a lot of
duplicate or unused code.
-----BEGIN PGP SIGNATURE-----
iIsEABYIADMWIQRgLjeFAZEXQzy86/s+p5+stXUA3QUCW3G6JxUccGF1bC5idXJ0
b25AbWlwcy5jb20ACgkQPqefrLV1AN0n/gD/Rpdgay31G/4eTTKBmBrcaju6Shjt
/2Iu6WC5Sj4hDHUBAJSbuI+B9YjcNsjekBYxB/LLD7ImcLBl6nLMIvKmXLAL
=cUiF
-----END PGP SIGNATURE-----
Merge tag 'mips_4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS updates from Paul Burton:
"Here are the main MIPS changes for 4.19.
An overview of the general architecture changes:
- Massive DMA ops refactoring from Christoph Hellwig (huzzah for
deleting crufty code!).
- We introduce NT_MIPS_DSP & NT_MIPS_FP_MODE ELF notes &
corresponding regsets to expose DSP ASE & floating point mode state
respectively, both for live debugging & core dumps.
- We better optimize our code by hard-coding cpu_has_* macros at
compile time where their values are known due to the ISA revision
that the kernel build is targeting.
- The EJTAG exception handler now better handles SMP systems, where
it was previously possible for CPUs to clobber a register value
saved by another CPU.
- Our implementation of memset() gained a couple of fixes for MIPSr6
systems to return correct values in some cases where stores fault.
- We now implement ioremap_wc() using the uncached-accelerated cache
coherency attribute where supported, which is detected during boot,
and fall back to plain uncached access where necessary. The
MIPS-specific (and unused in tree) ioremap_uncached_accelerated() &
ioremap_cacheable_cow() are removed.
- The prctl(PR_SET_FP_MODE, ...) syscall is better supported for SMP
systems by reworking the way we ensure remote CPUs that may be
running threads within the affected process switch mode.
- Systems using the MIPS Coherence Manager will now set the
MIPS_IC_SNOOPS_REMOTE flag to avoid some unnecessary cache
maintenance overhead when flushing the icache.
- A few fixes were made for building with clang/LLVM, which now
sucessfully builds kernels for many of our platforms.
- Miscellaneous cleanups all over.
And some platform-specific changes:
- ar7 gained stubs for a few clock API functions to fix build
failures for some drivers.
- ath79 gained support for a few new SoCs, a few fixes & better
gpio-keys support.
- Ci20 now exposes its SPI bus using the spi-gpio driver.
- The generic platform can now auto-detect a suitable value for
PHYS_OFFSET based upon the memory map described by the device tree,
allowing us to avoid wasting memory on page book-keeping for
systems where RAM starts at a non-zero physical address.
- Ingenic systems using the jz4740 platform code now link their
vmlinuz higher to allow for kernels of a realistic size.
- Loongson32 now builds the kernel targeting MIPSr1 rather than
MIPSr2 to avoid CPU errata.
- Loongson64 gains a couple of fixes, a workaround for a write
buffering issue & support for the Loongson 3A R3.1 CPU.
- Malta now uses the piix4-poweroff driver to handle powering down.
- Microsemi Ocelot gained support for its SPI bus & NOR flash, its
second MDIO bus and can now be supported by a FIT/.itb image.
- Octeon saw a bunch of header cleanups which remove a lot of
duplicate or unused code"
* tag 'mips_4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (123 commits)
MIPS: Remove remnants of UASM_ISA
MIPS: netlogic: xlr: Remove erroneous check in nlm_fmn_send()
MIPS: VDSO: Force link endianness
MIPS: Always specify -EB or -EL when using clang
MIPS: Use dins to simplify __write_64bit_c0_split()
MIPS: Use read-write output operand in __write_64bit_c0_split()
MIPS: Avoid using array as parameter to write_c0_kpgd()
MIPS: vdso: Allow clang's --target flag in VDSO cflags
MIPS: genvdso: Remove GOT checks
MIPS: Remove obsolete MIPS checks for DST node "chosen@0"
MIPS: generic: Remove input symbols from defconfig
MIPS: Delete unused code in linux32.c
MIPS: Remove unused sys_32_mmap2
MIPS: Remove nabi_no_regargs
mips: dts: mscc: enable spi and NOR flash support on ocelot PCB123
mips: dts: mscc: Add spi on Ocelot
MIPS: Loongson: Merge load addresses
MIPS: Loongson: Set Loongson32 to MIPS32R1
MIPS: mscc: ocelot: add interrupt controller properties to GPIO controller
MIPS: generic: Select MIPS_AUTO_PFN_OFFSET
...
Since at least the beginning of the git era we've declared our TLB
exception handling functions inconsistently. They're actually functions,
but we declare them as arrays of u32 where each u32 is an encoded
instruction. This has always been the case for arch/mips/mm/tlbex.c, and
has also been true for arch/mips/kernel/traps.c since commit
86a1708a9d ("MIPS: Make tlb exception handler definitions and
declarations match.") which aimed for consistency but did so by
consistently making the our C code inconsistent with our assembly.
This is all usually harmless, but when using GCC 7 or newer to build a
kernel targeting microMIPS (ie. CONFIG_CPU_MICROMIPS=y) it becomes
problematic. With microMIPS bit 0 of the program counter indicates the
ISA mode. When bit 0 is zero instructions are decoded using the standard
MIPS32 or MIPS64 ISA. When bit 0 is one instructions are decoded using
microMIPS. This means that function pointers become odd - their least
significant bit is one for microMIPS code. We work around this in cases
where we need to access code using loads & stores with our
msk_isa16_mode() macro which simply clears bit 0 of the value it is
given:
#define msk_isa16_mode(x) ((x) & ~0x1)
For example we do this for our TLB load handler in
build_r4000_tlb_load_handler():
u32 *p = (u32 *)msk_isa16_mode((ulong)handle_tlbl);
We then write code to p, expecting it to be suitably aligned (our LEAF
macro aligns functions on 4 byte boundaries, so (ulong)handle_tlbl will
give a value one greater than a multiple of 4 - ie. the start of a
function on a 4 byte boundary, with the ISA mode bit 0 set).
This worked fine up to GCC 6, but GCC 7 & onwards is smart enough to
presume that handle_tlbl which we declared as an array of u32s must be
aligned sufficiently that bit 0 of its address will never be set, and as
a result optimize out msk_isa16_mode(). This leads to p having an
address with bit 0 set, and when we go on to attempt to store code at
that address we take an address error exception due to the unaligned
memory access.
This leads to an exception prior to the kernel having configured its own
exception handlers, so we jump to whatever handlers the bootloader
configured. In the case of QEMU this results in a silent hang, since it
has no useful general exception vector.
Fix this by consistently declaring our TLB-related functions as
functions. For handle_tlbl(), handle_tlbs() & handle_tlbm() we do this
in asm/tlbex.h & we make use of the existing declaration of
tlbmiss_handler_setup_pgd() in asm/mmu_context.h. Our TLB handler
generation code in arch/mips/mm/tlbex.c is adjusted to deal with these
definitions, in most cases simply by casting the function pointers to
u32 pointers.
This allows us to include asm/mmu_context.h in arch/mips/mm/tlbex.c to
get the definitions of tlbmiss_handler_setup_pgd & pgd_current, removing
some needless duplication. Consistently using msk_isa16_mode() on
function pointers means we no longer need the
tlbmiss_handler_setup_pgd_start symbol so that is removed entirely.
Now that we're declaring our functions as functions GCC stops optimizing
out msk_isa16_mode() & a microMIPS kernel built with either GCC 7.3.0 or
8.1.0 boots successfully.
Signed-off-by: Paul Burton <paul.burton@mips.com>
We export tlbmiss_handler_setup_pgd in arch/mips/mm/tlbex.c close to a
declaration of it, rather than close to its definition as is standard.
We've supported exporting symbols in assembly code since commit
22823ab419 ("EXPORT_SYMBOL() for asm"), so move the export to follow
the function's (stub) definition.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Commit 33679a5037 ("MIPS: uasm: Remove needless ISA abstraction")
removed use of the MIPS_ISA preprocessor macro, but left a couple of
unused definitions of it behind.
Remove the dead code.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Passing an array (swapper_pg_dir) as the argument to write_c0_kpgd() in
setup_pw() will become problematic if we modify __write_64bit_c0_split()
to cast its val argument to unsigned long long, because for 32-bit
kernel builds the size of a pointer will differ from the size of an
unsigned long long. This would fall foul of gcc's pointer-to-int-cast
diagnostic.
Cast the value to a long, which should be the same width as the pointer
that we ultimately want & will be sign extended if required to the
unsigned long long that __write_64bit_c0_split() ultimately needs.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Converting an address between cached & uncached (typically addresses in
(c)kseg0 & (c)kseg1 or 2 xkphys regions) should not depend upon
PHYS_OFFSET in any way - we're converting from a virtual address in one
unmapped region to a virtual address in another unmapped region.
For some reason our CAC_ADDR() & UNCAC_ADDR() macros make use of
PAGE_OFFSET, which typically includes PHYS_OFFSET. This means that
platforms with a non-zero PHYS_OFFSET typically have to workaround
miscalculation by these 2 macros by also defining UNCAC_BASE to a value
that isn't really correct.
It appears that an attempt has previously been made to address this with
commit 3f4579252aa1 ("MIPS: make CAC_ADDR and UNCAC_ADDR account for
PHYS_OFFSET") which was later undone by commit ed3ce16c3d ("Revert
"MIPS: make CAC_ADDR and UNCAC_ADDR account for PHYS_OFFSET"") which
also introduced the ar7 workaround. That attempt at a fix was roughly
equivalent, but essentially caused the CAC_ADDR() & UNCAC_ADDR() macros
to cancel out PHYS_OFFSET by adding & then subtracting it again. In his
revert Leonid is correct that using PHYS_OFFSET makes no sense in the
context of these macros, but appears to have missed its inclusion via
PAGE_OFFSET which means PHYS_OFFSET actually had an effect after the
revert rather than before it.
Here we fix this by modifying CAC_ADDR() & UNCAC_ADDR() to stop using
PAGE_OFFSET (& thus PHYS_OFFSET), instead using __pa() & __va() along
with UNCAC_BASE.
For UNCAC_ADDR(), __pa() will convert a cached address to a physical
address which we can simply use as an offset from UNCAC_BASE to obtain
an address in the uncached region.
For CAC_ADDR() we can undo the effect of UNCAC_ADDR() by subtracting
UNCAC_BASE and using __va() on the result.
With this change made, remove definitions of UNCAC_BASE from the ar7 &
pic32 platforms which appear to have defined them only to workaround
this problem.
Signed-off-by: Paul Burton <paul.burton@mips.com>
References: 3f4579252aa1 ("MIPS: make CAC_ADDR and UNCAC_ADDR account for PHYS_OFFSET")
References: ed3ce16c3d ("Revert "MIPS: make CAC_ADDR and UNCAC_ADDR account for PHYS_OFFSET"")
Patchwork: https://patchwork.linux-mips.org/patch/20046/
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: Vladimir Kondratiev <vladimir.kondratiev@intel.com>
mips_swiotlb_ops differs from the generic swiotlb_dma_ops only in that
it contains a mb() barrier after each operations that maps or syncs
dma memory to the device.
The dma operations are defined to not be memory barriers, but instead
the write* operations to kick the DMA off are supposed to contain them.
For mips this handled by war_io_reorder_wmb(), which evaluates to the
stronger wmb() instead of the pure compiler barrier barrier() for
just those platforms that use swiotlb, so I think we are covered
properly.
[paul.burton@mips.com:
- Include linux/swiotlb.h to fix build failures for configs with
CONFIG_SWIOTLB=y.]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/20038/
Cc: David Daney <ddaney@caviumnetworks.com>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: linux-mips@linux-mips.org
Cc: iommu@lists.linux-foundation.org
Cc: linux-kernel@vger.kernel.org
If a driver causes DMA cache maintenance with a zero length then we
currently BUG and kill the kernel. As this is a scenario that we may
well be able to recover from, WARN & return in the condition instead.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/14623/
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
We currently attempt to check whether a physical address range provided
to __ioremap() may be in use by the page allocator by examining the
value of PageReserved for each page in the region - lowmem pages not
marked reserved are presumed to be in use by the page allocator, and
requests to ioremap them fail.
The way we check this has been broken since commit 92923ca3aa ("mm:
meminit: only set page reserved in the memblock region"), because
memblock will typically not have any knowledge of non-RAM pages and
therefore those pages will not have the PageReserved flag set. Thus when
we attempt to ioremap a region outside of RAM we incorrectly fail
believing that the region is RAM that may be in use.
In most cases ioremap() on MIPS will take a fast-path to use the
unmapped kseg1 or xkphys virtual address spaces and never hit this path,
so the only way to hit it is for a MIPS32 system to attempt to ioremap()
an address range in lowmem with flags other than _CACHE_UNCACHED.
Perhaps the most straightforward way to do this is using
ioremap_uncached_accelerated(), which is how the problem was discovered.
Fix this by making use of walk_system_ram_range() to test the address
range provided to __ioremap() against only RAM pages, rather than all
lowmem pages. This means that if we have a lowmem I/O region, which is
very common for MIPS systems, we're free to ioremap() address ranges
within it. A nice bonus is that the test is no longer limited to lowmem.
The approach here matches the way x86 performed the same test after
commit c81c8a1eee ("x86, ioremap: Speed up check for RAM pages") until
x86 moved towards a slightly more complicated check using walk_mem_res()
for unrelated reasons with commit 0e4c12b45a ("x86/mm, resource: Use
PAGE_KERNEL protection for ioremap of memory pages").
Signed-off-by: Paul Burton <paul.burton@mips.com>
Reported-by: Serge Semin <fancer.lancer@gmail.com>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Fixes: 92923ca3aa ("mm: meminit: only set page reserved in the memblock region")
Cc: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: stable@vger.kernel.org # v4.2+
Patchwork: https://patchwork.linux-mips.org/patch/19786/
Remove the function sb1_dma_init() that is not used anywhere.
This was partially found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Patchwork: https://patchwork.linux-mips.org/patch/8873/
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: John Crispin <blogic@openwrt.org>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
In systems that include a MIPS Coherency Manager, the icache always
fills from a cache which is coherent across all CPUs. In I6400 & I6500
systems the icache fills from the dcache which is coherent across all
CPUs. In all other CM-based systems the icache fills from the L2 cache
which is shared between all cores.
This means that an icache will always see stores from remote CPUs
without needing to write them back any further than that L2, which is
what the cpu_icache_snoops_remote_store feature is used to test. In
order for it to return 1 without needing a per-platform override (which
is what Malta has relied upon so far) set the MIPS_IC_SNOOPS_REMOTE flag
when a CM is present.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16200/
Convert everything not overriding dma-coherence.h to the generic
noncoherent ops. The new dma-noncoherent.c file duplicates a lot of
the code in dma-default.c, but that file will be gone by the end of
this series.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Patchwork: https://patchwork.linux-mips.org/patch/19544/
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: David Daney <david.daney@cavium.com>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Jiaxun Yang <jiaxun.yang@flygoat.com>
Cc: Tom Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: iommu@lists.linux-foundation.org
Cc: linux-mips@linux-mips.org
We want to be able to use it even when not building dma-default.c
in the near future.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Patchwork: https://patchwork.linux-mips.org/patch/19543/
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: David Daney <david.daney@cavium.com>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Jiaxun Yang <jiaxun.yang@flygoat.com>
Cc: Tom Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: iommu@lists.linux-foundation.org
Cc: linux-mips@linux-mips.org
Octeon and loonson64 already don't use it at all, and we're going to
migrate more plaforms away from it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Patchwork: https://patchwork.linux-mips.org/patch/19536/
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: David Daney <david.daney@cavium.com>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Jiaxun Yang <jiaxun.yang@flygoat.com>
Cc: Tom Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: iommu@lists.linux-foundation.org
Cc: linux-mips@linux-mips.org
Octeon and Loongson share exactly the same code, move it into a common
implementation, and use that implementation directly from get_arch_dma_ops.
Also provide the expected dma-direct.h helpers directly instead of
delegating to platform dma-coherence.h headers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Patchwork: https://patchwork.linux-mips.org/patch/19534/
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: David Daney <david.daney@cavium.com>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Jiaxun Yang <jiaxun.yang@flygoat.com>
Cc: Tom Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: iommu@lists.linux-foundation.org
Cc: linux-mips@linux-mips.org
CONFIG_DMA_MAYBE_COHERENT already selects CONFIG_DMA_NONCOHERENT, so we
can remove the extra conditions.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/19529/
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: David Daney <david.daney@cavium.com>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Jiaxun Yang <jiaxun.yang@flygoat.com>
Cc: Tom Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: iommu@lists.linux-foundation.org
Cc: linux-mips@linux-mips.org
Pull siginfo updates from Eric Biederman:
"This set of changes close the known issues with setting si_code to an
invalid value, and with not fully initializing struct siginfo. There
remains work to do on nds32, arc, unicore32, powerpc, arm, arm64, ia64
and x86 to get the code that generates siginfo into a simpler and more
maintainable state. Most of that work involves refactoring the signal
handling code and thus careful code review.
Also not included is the work to shrink the in kernel version of
struct siginfo. That depends on getting the number of places that
directly manipulate struct siginfo under control, as it requires the
introduction of struct kernel_siginfo for the in kernel things.
Overall this set of changes looks like it is making good progress, and
with a little luck I will be wrapping up the siginfo work next
development cycle"
* 'siginfo-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace: (46 commits)
signal/sh: Stop gcc warning about an impossible case in do_divide_error
signal/mips: Report FPE_FLTUNK for undiagnosed floating point exceptions
signal/um: More carefully relay signals in relay_signal.
signal: Extend siginfo_layout with SIL_FAULT_{MCEERR|BNDERR|PKUERR}
signal: Remove unncessary #ifdef SEGV_PKUERR in 32bit compat code
signal/signalfd: Add support for SIGSYS
signal/signalfd: Remove __put_user from signalfd_copyinfo
signal/xtensa: Use force_sig_fault where appropriate
signal/xtensa: Consistenly use SIGBUS in do_unaligned_user
signal/um: Use force_sig_fault where appropriate
signal/sparc: Use force_sig_fault where appropriate
signal/sparc: Use send_sig_fault where appropriate
signal/sh: Use force_sig_fault where appropriate
signal/s390: Use force_sig_fault where appropriate
signal/riscv: Replace do_trap_siginfo with force_sig_fault
signal/riscv: Use force_sig_fault where appropriate
signal/parisc: Use force_sig_fault where appropriate
signal/parisc: Use force_sig_mceerr where appropriate
signal/openrisc: Use force_sig_fault where appropriate
signal/nios2: Use force_sig_fault where appropriate
...
- replaceme the force_dma flag with a dma_configure bus method.
(Nipun Gupta, although one patch is іncorrectly attributed to me
due to a git rebase bug)
- use GFP_DMA32 more agressively in dma-direct. (Takashi Iwai)
- remove PCI_DMA_BUS_IS_PHYS and rely on the dma-mapping API to do the
right thing for bounce buffering.
- move dma-debug initialization to common code, and apply a few cleanups
to the dma-debug code.
- cleanup the Kconfig mess around swiotlb selection
- swiotlb comment fixup (Yisheng Xie)
- a trivial swiotlb fix. (Dan Carpenter)
- support swiotlb on RISC-V. (based on a patch from Palmer Dabbelt)
- add a new generic dma-noncoherent dma_map_ops implementation and use
it for arc, c6x and nds32.
- improve scatterlist validity checking in dma-debug. (Robin Murphy)
- add a struct device quirk to limit the dma-mask to 32-bit due to
bridge/system issues, and switch x86 to use it instead of a local
hack for VIA bridges.
- handle devices without a dma_mask more gracefully in the dma-direct
code.
-----BEGIN PGP SIGNATURE-----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=6Acj
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-4.18' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping updates from Christoph Hellwig:
- replace the force_dma flag with a dma_configure bus method. (Nipun
Gupta, although one patch is іncorrectly attributed to me due to a
git rebase bug)
- use GFP_DMA32 more agressively in dma-direct. (Takashi Iwai)
- remove PCI_DMA_BUS_IS_PHYS and rely on the dma-mapping API to do the
right thing for bounce buffering.
- move dma-debug initialization to common code, and apply a few
cleanups to the dma-debug code.
- cleanup the Kconfig mess around swiotlb selection
- swiotlb comment fixup (Yisheng Xie)
- a trivial swiotlb fix. (Dan Carpenter)
- support swiotlb on RISC-V. (based on a patch from Palmer Dabbelt)
- add a new generic dma-noncoherent dma_map_ops implementation and use
it for arc, c6x and nds32.
- improve scatterlist validity checking in dma-debug. (Robin Murphy)
- add a struct device quirk to limit the dma-mask to 32-bit due to
bridge/system issues, and switch x86 to use it instead of a local
hack for VIA bridges.
- handle devices without a dma_mask more gracefully in the dma-direct
code.
* tag 'dma-mapping-4.18' of git://git.infradead.org/users/hch/dma-mapping: (48 commits)
dma-direct: don't crash on device without dma_mask
nds32: use generic dma_noncoherent_ops
nds32: implement the unmap_sg DMA operation
nds32: consolidate DMA cache maintainance routines
x86/pci-dma: switch the VIA 32-bit DMA quirk to use the struct device flag
x86/pci-dma: remove the explicit nodac and allowdac option
x86/pci-dma: remove the experimental forcesac boot option
Documentation/x86: remove a stray reference to pci-nommu.c
core, dma-direct: add a flag 32-bit dma limits
dma-mapping: remove unused gfp_t parameter to arch_dma_alloc_attrs
dma-debug: check scatterlist segments
c6x: use generic dma_noncoherent_ops
arc: use generic dma_noncoherent_ops
arc: fix arc_dma_{map,unmap}_page
arc: fix arc_dma_sync_sg_for_{cpu,device}
arc: simplify arc_dma_sync_single_for_{cpu,device}
dma-mapping: provide a generic dma-noncoherent implementation
dma-mapping: simplify Kconfig dependencies
riscv: add swiotlb support
riscv: only enable ZONE_DMA32 for 64-bit
...
When DMA will be performed to a MIPS32 1004K CPS, the L1-cache for the
range needs to be flushed and invalidated first.
The code currently takes one of two approaches.
1/ If the range is less than the size of the dcache, then HIT type
requests flush/invalidate cache lines for the particular addresses.
HIT-type requests a globalised by the CPS so this is safe on SMP.
2/ If the range is larger than the size of dcache, then INDEX type
requests flush/invalidate the whole cache. INDEX type requests affect
the local cache only. CPS does not propagate them in any way. So this
invalidation is not safe on SMP CPS systems.
Data corruption due to '2' can quite easily be demonstrated by
repeatedly "echo 3 > /proc/sys/vm/drop_caches" and then sha1sum a file
that is several times the size of available memory. Dropping caches
means that large contiguous extents (large than dcache) are more likely.
This was not a problem before Linux-4.8 because option 2 was never used
if CONFIG_MIPS_CPS was defined. The commit which removed that apparently
didn't appreciate the full consequence of the change.
We could, in theory, globalize the INDEX based flush by sending an IPI
to other cores. These cache invalidation routines can be called with
interrupts disabled and synchronous IPI require interrupts to be
enabled. Asynchronous IPI may not trigger writeback soon enough. So we
cannot use IPI in practice.
We can already test if IPI would be needed for an INDEX operation with
r4k_op_needs_ipi(R4K_INDEX). If this is true then we mustn't try the
INDEX approach as we cannot use IPI. If this is false (e.g. when there
is only one core and hence one L1 cache) then it is safe to use the
INDEX approach without IPI.
This patch avoids options 2 if r4k_op_needs_ipi(R4K_INDEX), and so
eliminates the corruption.
Fixes: c00ab4896e ("MIPS: Remove cpu_has_safe_index_cacheops")
Signed-off-by: NeilBrown <neil@brown.name>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@linux-mips.org
Cc: <stable@vger.kernel.org> # 4.8+
Patchwork: https://patchwork.linux-mips.org/patch/19259/
Signed-off-by: James Hogan <jhogan@kernel.org>
Most mainstream architectures are using 65536 entries, so lets stick to
that. If someone is really desperate to override it that can still be
done through <asm/dma-mapping.h>, but I'd rather see a really good
rationale for that.
dma_debug_init is now called as a core_initcall, which for many
architectures means much earlier, and provides dma-debug functionality
earlier in the boot process. This should be safe as it only relies
on the memory allocator already being available.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Filling in struct siginfo before calling force_sig_info a tedious and
error prone process, where once in a great while the wrong fields
are filled out, and siginfo has been inconsistently cleared.
Simplify this process by using the helper force_sig_fault. Which
takes as a parameters all of the information it needs, ensures
all of the fiddly bits of filling in struct siginfo are done properly
and then calls force_sig_info.
In short about a 5 line reduction in code for every time force_sig_info
is called, which makes the calling function clearer.
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@linux-mips.org
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Call clear_siginfo to ensure every stack allocated siginfo is properly
initialized before being passed to the signal sending functions.
Note: It is not safe to depend on C initializers to initialize struct
siginfo on the stack because C is allowed to skip holes when
initializing a structure.
The initialization of struct siginfo in tracehook_report_syscall_exit
was moved from the helper user_single_step_siginfo into
tracehook_report_syscall_exit itself, to make it clear that the local
variable siginfo gets fully initialized.
In a few cases the scope of struct siginfo has been reduced to make it
clear that siginfo siginfo is not used on other paths in the function
in which it is declared.
Instances of using memset to initialize siginfo have been replaced
with calls clear_siginfo for clarity.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
__get_user_pages_fast handles errors differently from
get_user_pages_fast: the former always returns the number of pages
pinned, the later might return a negative error code.
Link: http://lkml.kernel.org/r/1522962072-182137-6-git-send-email-mst@redhat.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Huang Ying <ying.huang@intel.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Thorsten Leemhuis <regressions@leemhuis.info>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Patch series "exec: Pin stack limit during exec".
Attempts to solve problems with the stack limit changing during exec
continue to be frustrated[1][2]. In addition to the specific issues
around the Stack Clash family of flaws, Andy Lutomirski pointed out[3]
other places during exec where the stack limit is used and is assumed to
be unchanging. Given the many places it gets used and the fact that it
can be manipulated/raced via setrlimit() and prlimit(), I think the only
way to handle this is to move away from the "current" view of the stack
limit and instead attach it to the bprm, and plumb this down into the
functions that need to know the stack limits. This series implements
the approach.
[1] 04e35f4495 ("exec: avoid RLIMIT_STACK races with prlimit()")
[2] 779f4e1c6c ("Revert "exec: avoid RLIMIT_STACK races with prlimit()"")
[3] to security@kernel.org, "Subject: existing rlimit races?"
This patch (of 3):
Since it is possible that the stack rlimit can change externally during
exec (either via another thread calling setrlimit() or another process
calling prlimit()), provide a way to pass the rlimit down into the
per-architecture mm layout functions so that the rlimit can stay in the
bprm structure instead of sitting in the signal structure until exec is
finalized.
Link: http://lkml.kernel.org/r/1518638796-20819-2-git-send-email-keescook@chromium.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Ben Hutchings <ben@decadent.org.uk>
Cc: Willy Tarreau <w@1wt.eu>
Cc: Hugh Dickins <hughd@google.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: "Jason A. Donenfeld" <Jason@zx2c4.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Laura Abbott <labbott@redhat.com>
Cc: Greg KH <greg@kroah.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Ben Hutchings <ben.hutchings@codethink.co.uk>
Cc: Brad Spengler <spender@grsecurity.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
These are the main MIPS changes for 4.17. Rough overview:
(1) generic platform: Add support for Microsemi Ocelot SoCs
(2) crypto: Add CRC32 and CRC32C HW acceleration module
(3) Various cleanups and misc improvements
Miscellaneous:
- Hang more efficiently on halt/powerdown/restart
- pm-cps: Block system suspend when a JTAG probe is present
- Expand make help text for generic defconfigs
- Refactor handling of legacy defconfigs
- Determine the entry point from the ELF file header to fix microMIPS
for certain toolchains
- Introduce isa-rev.h for MIPS_ISA_REV and use to simplify other code
Minor cleanups:
- DTS: boston/ci20: Unit name cleanups and correction
- kdump: Make the default for PHYSICAL_START always 64-bit
- Constify gpio_led in Alchemy, AR7, and TXX9
- Silence a couple of W=1 warnings
- Remove duplicate includes
Platform support:
ath79:
- Fix AR724X_PLL_REG_PCIE_CONFIG offset
BCM47xx:
- FIRMWARE: Use mac_pton() for MAC address parsing
- Add Luxul XAP1500/XWR1750 WiFi LEDs
- Use standard reset button for Luxul XWR-1750
BMIPS:
- Enable CONFIG_BRCMSTB_PM in bmips_stb_defconfig for build coverage
- Add STB PM, wake-up timer, watchdog DT nodes
Generic platform:
- Add support for Microsemi Ocelot
- dt-bindings: Add vendor prefix for Microsemi Corporation
- dt-bindings: Add bindings for Microsemi SoCs
- Add ocelot SoC & PCB123 board DTS files
- MAINTAINERS: Add entry for Microsemi MIPS SoCs
- Enable crc32-mips on r6 configs
Octeon:
- Drop '.' after newlines in printk calls
ralink:
- pci-mt7621: Enable PCIe on MT7688
-----BEGIN PGP SIGNATURE-----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=4vUc
-----END PGP SIGNATURE-----
Merge tag 'mips_4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/mips
Pull MIPS updates from James Hogan:
"These are the main MIPS changes for 4.17. Rough overview:
(1) generic platform: Add support for Microsemi Ocelot SoCs
(2) crypto: Add CRC32 and CRC32C HW acceleration module
(3) Various cleanups and misc improvements
More detailed summary:
Miscellaneous:
- hang more efficiently on halt/powerdown/restart
- pm-cps: Block system suspend when a JTAG probe is present
- expand make help text for generic defconfigs
- refactor handling of legacy defconfigs
- determine the entry point from the ELF file header to fix microMIPS
for certain toolchains
- introduce isa-rev.h for MIPS_ISA_REV and use to simplify other code
Minor cleanups:
- DTS: boston/ci20: Unit name cleanups and correction
- kdump: Make the default for PHYSICAL_START always 64-bit
- constify gpio_led in Alchemy, AR7, and TXX9
- silence a couple of W=1 warnings
- remove duplicate includes
Platform support:
Generic platform:
- add support for Microsemi Ocelot
- dt-bindings: Add vendor prefix for Microsemi Corporation
- dt-bindings: Add bindings for Microsemi SoCs
- add ocelot SoC & PCB123 board DTS files
- MAINTAINERS: Add entry for Microsemi MIPS SoCs
- enable crc32-mips on r6 configs
ath79:
- fix AR724X_PLL_REG_PCIE_CONFIG offset
BCM47xx:
- firmware: Use mac_pton() for MAC address parsing
- add Luxul XAP1500/XWR1750 WiFi LEDs
- use standard reset button for Luxul XWR-1750
BMIPS:
- enable CONFIG_BRCMSTB_PM in bmips_stb_defconfig for build coverage
- add STB PM, wake-up timer, watchdog DT nodes
Octeon:
- drop '.' after newlines in printk calls
ralink:
- pci-mt7621: Enable PCIe on MT7688"
* tag 'mips_4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/mips: (37 commits)
MIPS: BCM47XX: Use standard reset button for Luxul XWR-1750
MIPS: BCM47XX: Add Luxul XAP1500/XWR1750 WiFi LEDs
MIPS: Make the default for PHYSICAL_START always 64-bit
MIPS: Use the entry point from the ELF file header
MAINTAINERS: Add entry for Microsemi MIPS SoCs
MIPS: generic: Add support for Microsemi Ocelot
MIPS: mscc: Add ocelot PCB123 device tree
MIPS: mscc: Add ocelot dtsi
dt-bindings: mips: Add bindings for Microsemi SoCs
dt-bindings: Add vendor prefix for Microsemi Corporation
MIPS: ath79: Fix AR724X_PLL_REG_PCIE_CONFIG offset
MIPS: pci-mt7620: Enable PCIe on MT7688
MIPS: pm-cps: Block system suspend when a JTAG probe is present
MIPS: VDSO: Replace __mips_isa_rev with MIPS_ISA_REV
MIPS: BPF: Replace __mips_isa_rev with MIPS_ISA_REV
MIPS: cpu-features.h: Replace __mips_isa_rev with MIPS_ISA_REV
MIPS: Introduce isa-rev.h to define MIPS_ISA_REV
MIPS: Hang more efficiently on halt/powerdown/restart
FIRMWARE: bcm47xx_nvram: Replace mac address parsing
MIPS: BMIPS: Add Broadcom STB watchdog nodes
...
Thanks to commit 4b3ef9daa4 ("mm/swap: split swap cache into 64MB
trunks"), after swapoff the address_space associated with the swap
device will be freed. So page_mapping() users which may touch the
address_space need some kind of mechanism to prevent the address_space
from being freed during accessing.
The dcache flushing functions (flush_dcache_page(), etc) in architecture
specific code may access the address_space of swap device for anonymous
pages in swap cache via page_mapping() function. But in some cases
there are no mechanisms to prevent the swap device from being swapoff,
for example,
CPU1 CPU2
__get_user_pages() swapoff()
flush_dcache_page()
mapping = page_mapping()
... exit_swap_address_space()
... kvfree(spaces)
mapping_mapped(mapping)
The address space may be accessed after being freed.
But from cachetlb.txt and Russell King, flush_dcache_page() only care
about file cache pages, for anonymous pages, flush_anon_page() should be
used. The implementation of flush_dcache_page() in all architectures
follows this too. They will check whether page_mapping() is NULL and
whether mapping_mapped() is true to determine whether to flush the
dcache immediately. And they will use interval tree (mapping->i_mmap)
to find all user space mappings. While mapping_mapped() and
mapping->i_mmap isn't used by anonymous pages in swap cache at all.
So, to fix the race between swapoff and flush dcache, __page_mapping()
is add to return the address_space for file cache pages and NULL
otherwise. All page_mapping() invoking in flush dcache functions are
replaced with page_mapping_file().
[akpm@linux-foundation.org: simplify page_mapping_file(), per Mike]
Link: http://lkml.kernel.org/r/20180305083634.15174-1-ying.huang@intel.com
Signed-off-by: "Huang, Ying" <ying.huang@intel.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Chen Liqin <liqin.linux@gmail.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Chris Zankel <chris@zankel.net>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
These duplicate includes have been found with scripts/checkincludes.pl
but they have been removed manually to avoid removing false positives.
Signed-off-by: Pravin Shedge <pravin.shedge4linux@gmail.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17920/
Signed-off-by: James Hogan <jhogan@kernel.org>
These are the main MIPS changes for 4.16. Rough overview:
- Basic support for the Ingenic JZ4770 based GCW Zero open-source
handheld video game console
- Support for the Ranchu board (used by Android emulator)
- Various cleanups and misc improvements
Fixes:
- Fix generic platform's USB_*HCI_BIG_ENDIAN selects (4.9)
- Fix vmlinuz default build when ZBOOT selected
- Fix clean up of vmlinuz targets
- Fix command line duplication (in preparation for Ingenic JZ4770)
Miscellaneous:
- Allow Processor ID reads to be to be optimised away by the compiler
(improves performance when running in guest)
- Push ARCH_MIGHT_HAVE_PC_SERIO/PARPORT down to platform level to
disable on generic platform with Ranchu board support
- Add helpers for assembler macro instructions for older assemblers
- Use assembler macro instructions to support VZ, XPA & MSA operations
on older assemblers, removing C wrapper duplication
- Various improvements to VZ & XPA assembly wrappers
- Add drivers/platform/mips/ to MIPS MAINTAINERS entry
Minor cleanups:
- Misc FPU emulation cleanups (removal of unnecessary include, moving
macros to common header, checkpatch and sparse fixes)
- Remove duplicate assignment of core in play_dead()
- Remove duplication in watchpoint handling
- Remove mips_dma_mapping_error() stub
- Use NULL instead of 0 in prepare_ftrace_return()
- Use proper kernel-doc Return keyword for
__compute_return_epc_for_insn()
- Remove duplicate semicolon in csum_fold()
Platform support:
Broadcom:
- Enable ZBOOT on BCM47xx
Generic platform:
- Add Ranchu board support, used by Android emulator
- Fix machine compatible string matching for Ranchu
- Support GIC in EIC mode
Ingenic platforms:
- Add DT, defconfig and other support for JZ4770 SoC and GCW Zero
- Support dynamnic machine types (i.e. JZ4740 / JZ4770 / JZ4780)
- Add Ingenic JZ4770 CGU clocks
- General Ingenic clk changes to prepare for JZ4770 SoC support
- Use common command line handling code
- Add DT vendor prefix to GCW (Game Consoles Worldwide)
Loongson:
- Add MAINTAINERS entry for Loongson2 and Loongson3 platforms
- Drop 32-bit support for Loongson 2E/2F devices
- Fix build failures due to multiple use of "MEM_RESERVED"
-----BEGIN PGP SIGNATURE-----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=7iwT
-----END PGP SIGNATURE-----
Merge tag 'mips_4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/mips
Pull MIPS updates from James Hogan:
"These are the main MIPS changes for 4.16.
Rough overview:
(1) Basic support for the Ingenic JZ4770 based GCW Zero open-source
handheld video game console
(2) Support for the Ranchu board (used by Android emulator)
(3) Various cleanups and misc improvements
More detailed summary:
Fixes:
- Fix generic platform's USB_*HCI_BIG_ENDIAN selects (4.9)
- Fix vmlinuz default build when ZBOOT selected
- Fix clean up of vmlinuz targets
- Fix command line duplication (in preparation for Ingenic JZ4770)
Miscellaneous:
- Allow Processor ID reads to be to be optimised away by the compiler
(improves performance when running in guest)
- Push ARCH_MIGHT_HAVE_PC_SERIO/PARPORT down to platform level to
disable on generic platform with Ranchu board support
- Add helpers for assembler macro instructions for older assemblers
- Use assembler macro instructions to support VZ, XPA & MSA
operations on older assemblers, removing C wrapper duplication
- Various improvements to VZ & XPA assembly wrappers
- Add drivers/platform/mips/ to MIPS MAINTAINERS entry
Minor cleanups:
- Misc FPU emulation cleanups (removal of unnecessary include, moving
macros to common header, checkpatch and sparse fixes)
- Remove duplicate assignment of core in play_dead()
- Remove duplication in watchpoint handling
- Remove mips_dma_mapping_error() stub
- Use NULL instead of 0 in prepare_ftrace_return()
- Use proper kernel-doc Return keyword for
__compute_return_epc_for_insn()
- Remove duplicate semicolon in csum_fold()
Platform support:
Broadcom:
- Enable ZBOOT on BCM47xx
Generic platform:
- Add Ranchu board support, used by Android emulator
- Fix machine compatible string matching for Ranchu
- Support GIC in EIC mode
Ingenic platforms:
- Add DT, defconfig and other support for JZ4770 SoC and GCW Zero
- Support dynamnic machine types (i.e. JZ4740 / JZ4770 / JZ4780)
- Add Ingenic JZ4770 CGU clocks
- General Ingenic clk changes to prepare for JZ4770 SoC support
- Use common command line handling code
- Add DT vendor prefix to GCW (Game Consoles Worldwide)
Loongson:
- Add MAINTAINERS entry for Loongson2 and Loongson3 platforms
- Drop 32-bit support for Loongson 2E/2F devices
- Fix build failures due to multiple use of 'MEM_RESERVED'"
* tag 'mips_4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/mips: (53 commits)
MIPS: Malta: Sanitize mouse and keyboard configuration.
MIPS: Update defconfigs after previous patch.
MIPS: Push ARCH_MIGHT_HAVE_PC_SERIO down to platform level
MIPS: Push ARCH_MIGHT_HAVE_PC_PARPORT down to platform level
MIPS: SMP-CPS: Remove duplicate assignment of core in play_dead
MIPS: Generic: Support GIC in EIC mode
MIPS: generic: Fix Makefile alignment
MIPS: generic: Fix ranchu_of_match[] termination
MIPS: generic: Fix machine compatible matching
MIPS: Loongson fix name confict - MEM_RESERVED
MIPS: bcm47xx: enable ZBOOT support
MIPS: Fix trailing semicolon
MIPS: Watch: Avoid duplication of bits in mips_read_watch_registers
MIPS: Watch: Avoid duplication of bits in mips_install_watch_registers.
MIPS: MSA: Update helpers to use new asm macros
MIPS: XPA: Standardise readx/writex accessors
MIPS: XPA: Allow use of $0 (zero) to MTHC0
MIPS: XPA: Use XPA instructions in assembly
MIPS: VZ: Pass GC0 register names in $n format
MIPS: VZ: Update helpers to use new asm macros
...
This pull requests contains a consolidation of the generic no-IOMMU code,
a well as the glue code for swiotlb. All the code is based on the x86
implementation with hooks to allow all architectures that aren't cache
coherent to use it. The x86 conversion itself has been deferred because
the x86 maintainers were a little busy in the last months.
-----BEGIN PGP SIGNATURE-----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=Nrl9
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-4.16' of git://git.infradead.org/users/hch/dma-mapping
Pull dma mapping updates from Christoph Hellwig:
"Except for a runtime warning fix from Christian this is all about
consolidation of the generic no-IOMMU code, a well as the glue code
for swiotlb.
All the code is based on the x86 implementation with hooks to allow
all architectures that aren't cache coherent to use it.
The x86 conversion itself has been deferred because the x86
maintainers were a little busy in the last months"
* tag 'dma-mapping-4.16' of git://git.infradead.org/users/hch/dma-mapping: (57 commits)
MAINTAINERS: add the iommu list for swiotlb and xen-swiotlb
arm64: use swiotlb_alloc and swiotlb_free
arm64: replace ZONE_DMA with ZONE_DMA32
mips: use swiotlb_{alloc,free}
mips/netlogic: remove swiotlb support
tile: use generic swiotlb_ops
tile: replace ZONE_DMA with ZONE_DMA32
unicore32: use generic swiotlb_ops
ia64: remove an ifdef around the content of pci-dma.c
ia64: clean up swiotlb support
ia64: use generic swiotlb_ops
ia64: replace ZONE_DMA with ZONE_DMA32
swiotlb: remove various exports
swiotlb: refactor coherent buffer allocation
swiotlb: refactor coherent buffer freeing
swiotlb: wire up ->dma_supported in swiotlb_dma_ops
swiotlb: add common swiotlb_map_ops
swiotlb: rename swiotlb_free to swiotlb_exit
x86: rename swiotlb_dma_ops
powerpc: rename swiotlb_dma_ops
...
According to config2, the associativity would be 5-ways, but the
documentation states 4-ways, which also matches the documented
L2 cache size of 256 kB.
Signed-off-by: Maarten ter Huurne <maarten@treewalker.org>
Reviewed-by: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/18488/
Signed-off-by: James Hogan <jhogan@kernel.org>
Lift the code from x86 so that we behave consistently. In the future we
should probably warn if any of these is set.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org> [m68k]
These are the main MIPS changes for 4.15.
Fixes:
- ralink: Fix MT7620 PCI build issues (4.5)
- Disable cmpxchg64() and HAVE_VIRT_CPU_ACCOUNTING_GEN for 32-bit SMP
(4.1)
- Fix MIPS64 FP save/restore on 32-bit kernels (4.0)
- ptrace: Pick up ptrace/seccomp changed syscall numbers (3.19)
- ralink: Fix MT7628 pinmux (3.19)
- BCM47XX: Fix LED inversion on WRT54GSv1 (3.17)
- Fix n32 core dumping as o32 since regset support (3.13)
- ralink: Drop obsolete USB_ARCH_HAS_HCD select
Build system:
- Default to "generic" (multiplatform) system type instead of IP22
- Use generic little endian MIPS32 r2 configuration as default defconfig
instead of ip22_defconfig
FPU emulation:
- Fix exception generation for certain R6 FPU instructions
SMP:
- Allow __cpu_number_map to be larger than NR_CPUS for sparse CPU id
spaces
Miscellaneous:
- Add iomem resource for kernel bss section for kexec/kdump
- Atomics: Nudge writes on bit unlock
- DT files: Standardise "ok" -> "okay"
Platform support:
BMIPS:
- Enable HARDIRQS_SW_RESEND
Broadcom BCM63XX:
- Add clkdev lookup support
- Update clk driver, UART driver, DTs to handle named refclk from DTs
- Split apart various clocks to more closely match hardware
- Add ethernet clocks
Cavium Octeon:
- Remove usage of cvmx_wait() in favour of __delay()
ImgTec Pistachio:
- DT: Drop deprecated dwmmc num-slots property
Ingenic JZ4780:
- Add NFS root to Ci20 defconfig
- Add watchdog to Ci20 DT & defconfig, and allow building of watchdog
driver with this SoC
Generic (multiplatform):
- Migrate xilfpga (MIPSfpga) platform to the generic platform
Lantiq xway:
- Fix ASC0/ASC1 clocks
Minor cleanups:
- Define virt_to_pfn()
- Make thread_saved_pc static
- Simplify 32-bit sign extension in __read_64bit_c0_split()
- DMA: Use vma_pages() helper
- FPU emulation: Replace unsigned with unsigned int
- MM: Removed unused lastpfn
- Alchemy: Make clk_ops const
- Lasat: Use setup_timer() helper
- ralink: Use BIT() in MT7620 PCI driver
-----BEGIN PGP SIGNATURE-----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=xbL0
-----END PGP SIGNATURE-----
Merge tag 'mips_4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/mips
Pull MIPS updates from James Hogan:
"These are the main MIPS changes for 4.15.
Fixes:
- ralink: Fix MT7620 PCI build issues (4.5)
- Disable cmpxchg64() and HAVE_VIRT_CPU_ACCOUNTING_GEN for 32-bit SMP
(4.1)
- Fix MIPS64 FP save/restore on 32-bit kernels (4.0)
- ptrace: Pick up ptrace/seccomp changed syscall numbers (3.19)
- ralink: Fix MT7628 pinmux (3.19)
- BCM47XX: Fix LED inversion on WRT54GSv1 (3.17)
- Fix n32 core dumping as o32 since regset support (3.13)
- ralink: Drop obsolete USB_ARCH_HAS_HCD select
Build system:
- Default to "generic" (multiplatform) system type instead of IP22
- Use generic little endian MIPS32 r2 configuration as default
defconfig instead of ip22_defconfig
FPU emulation:
- Fix exception generation for certain R6 FPU instructions
SMP:
- Allow __cpu_number_map to be larger than NR_CPUS for sparse CPU id
spaces
Miscellaneous:
- Add iomem resource for kernel bss section for kexec/kdump
- Atomics: Nudge writes on bit unlock
- DT files: Standardise "ok" -> "okay"
Minor cleanups:
- Define virt_to_pfn()
- Make thread_saved_pc static
- Simplify 32-bit sign extension in __read_64bit_c0_split()
- DMA: Use vma_pages() helper
- FPU emulation: Replace unsigned with unsigned int
- MM: Removed unused lastpfn
- Alchemy: Make clk_ops const
- Lasat: Use setup_timer() helper
- ralink: Use BIT() in MT7620 PCI driver
Platform support:
BMIPS:
- Enable HARDIRQS_SW_RESEND
Broadcom BCM63XX:
- Add clkdev lookup support
- Update clk driver, UART driver, DTs to handle named refclk from DTs
- Split apart various clocks to more closely match hardware
- Add ethernet clocks
Cavium Octeon:
- Remove usage of cvmx_wait() in favour of __delay()
ImgTec Pistachio:
- DT: Drop deprecated dwmmc num-slots property
Ingenic JZ4780:
- Add NFS root to Ci20 defconfig
- Add watchdog to Ci20 DT & defconfig, and allow building of watchdog
driver with this SoC
Generic (multiplatform):
- Migrate xilfpga (MIPSfpga) platform to the generic platform
Lantiq xway:
- Fix ASC0/ASC1 clocks"
* tag 'mips_4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/mips: (46 commits)
MIPS: Add iomem resource for kernel bss section.
MIPS: cmpxchg64() and HAVE_VIRT_CPU_ACCOUNTING_GEN don't work for 32-bit SMP
MIPS: BMIPS: Enable HARDIRQS_SW_RESEND
MIPS: pci: Make use of the BIT() macro inside the mt7620 driver
MIPS: pci: Remove KERN_WARN instance inside the mt7620 driver
MIPS: pci: Remove duplicate define in mt7620 driver
MIPS: ralink: Fix typo in mt7628 pinmux function
MIPS: ralink: Fix MT7628 pinmux
MIPS: Fix odd fp register warnings with MIPS64r2
watchdog: jz4780: Allow selection of jz4740-wdt driver
MIPS/ptrace: Update syscall nr on register changes
MIPS/ptrace: Pick up ptrace/seccomp changed syscalls
MIPS: Fix an n32 core file generation regset support regression
MIPS: Fix MIPS64 FP save/restore on 32-bit kernels
MIPS: page.h: Define virt_to_pfn()
MIPS: Xilfpga: Switch to using generic defconfigs
MIPS: generic: Add support for MIPSfpga
MIPS: Set defconfig target to a generic system for 32r2el
MIPS: Kconfig: Set default MIPS system type as generic
MIPS: DTS: Remove num-slots from Pistachio SoC
...
- turn dma_cache_sync into a dma_map_ops instance and remove
implementation that purely are dead because the architecture
doesn't support noncoherent allocations
- add a flag for busses that need DMA configuration (Robin Murphy)
-----BEGIN PGP SIGNATURE-----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=ALJf
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-4.15' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping updates from Christoph Hellwig:
- turn dma_cache_sync into a dma_map_ops instance and remove
implementation that purely are dead because the architecture doesn't
support noncoherent allocations
- add a flag for busses that need DMA configuration (Robin Murphy)
* tag 'dma-mapping-4.15' of git://git.infradead.org/users/hch/dma-mapping:
dma-mapping: turn dma_cache_sync into a dma_map_ops method
sh: make dma_cache_sync a no-op
xtensa: make dma_cache_sync a no-op
unicore32: make dma_cache_sync a no-op
powerpc: make dma_cache_sync a no-op
mn10300: make dma_cache_sync a no-op
microblaze: make dma_cache_sync a no-op
ia64: make dma_cache_sync a no-op
frv: make dma_cache_sync a no-op
x86: make dma_cache_sync a no-op
floppy: consolidate the dummy fd_cacheflush definition
drivers: flag buses which demand DMA configuration
A selection of important MIPS fixes for 4.14, and some MAINTAINERS /
email address updates:
- Update imgtec.com -> mips.com email addresses (this trivially updates
comments in quite a few files, as well as MAINTAINERS)
- Update Pistachio SoC maintainership
- Fix NI 169445 build (new platform in 4.14)
- Fix EVA regression (4.14)
- Fix SMP-CPS build & preemption regressions (4.14)
- Fix SMP/hotplug deadlock & race (deadlock reintroduced 4.13)
- Fix ebpf_jit error return (4.13)
- Fix SMP-CMP build regressions (4.11 and 4.14)
- Fix bad UASM microMIPS encoding (3.16)
- Fix CM definitions (3.15)
-----BEGIN PGP SIGNATURE-----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=nqbK
-----END PGP SIGNATURE-----
Merge tag 'mips_fixes_4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/mips
Pull MIPS fixes from James Hogan:
"A selection of important MIPS fixes for 4.14, and some MAINTAINERS /
email address updates:
Maintainership updates:
- imgtec.com -> mips.com email addresses (this trivially updates
comments in quite a few files, as well as MAINTAINERS)
- Pistachio SoC maintainership update
Fixes:
- NI 169445 build (new platform in 4.14)
- EVA regression (4.14)
- SMP-CPS build & preemption regressions (4.14)
- SMP/hotplug deadlock & race (deadlock reintroduced 4.13)
- ebpf_jit error return (4.13)
- SMP-CMP build regressions (4.11 and 4.14)
- bad UASM microMIPS encoding (3.16)
- CM definitions (3.15)"
[ I had taken the email address updates separately, because I didn't
expect James to send a pull request, so those got applied twice. - Linus]
* tag 'mips_fixes_4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/mips:
MIPS: Update email address for Marcin Nowakowski
MIPS: smp-cmp: Fix vpe_id build error
MAINTAINERS: Update Pistachio platform maintainers
MIPS: smp-cmp: Use right include for task_struct
MIPS: Update Goldfish RTC driver maintainer email address
MIPS: Update RINT emulation maintainer email address
MIPS: CPS: Fix use of current_cpu_data in preemptible code
MIPS: SMP: Fix deadlock & online race
MIPS: bpf: Fix a typo in build_one_insn()
MIPS: microMIPS: Fix incorrect mask in insn_table_MM
MIPS: Fix CM region target definitions
MIPS: generic: Fix compilation error from include asm/mips-cpc.h
MIPS: Fix exception entry when CONFIG_EVA enabled
MIPS: generic: Fix NI 169445 its build
Update MIPS email addresses
MIPS will soon not be a part of Imagination Technologies, and as such
many @imgtec.com email addresses will no longer be valid. This patch
updates the addresses for those who:
- Have 10 or more patches in mainline authored using an @imgtec.com
email address, or any patches dated within the past year.
- Are still with Imagination but leaving as part of the MIPS business
unit, as determined from an internal email address list.
- Haven't already updated their email address (ie. JamesH) or expressed
a desire to be excluded (ie. Maciej).
- Acked v2 or earlier of this patch, which leaves Deng-Cheng, Matt &
myself.
New addresses are of the form firstname.lastname@mips.com, and all
verified against an internal email address list. An entry is added to
.mailmap for each person such that get_maintainer.pl will report the new
addresses rather than @imgtec.com addresses which will soon be dead.
Instances of the affected addresses throughout the tree are then
mechanically replaced with the new @mips.com address.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Deng-Cheng Zhu <dengcheng.zhu@imgtec.com>
Cc: Deng-Cheng Zhu <dengcheng.zhu@mips.com>
Acked-by: Dengcheng Zhu <dengcheng.zhu@mips.com>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Matt Redfearn <matt.redfearn@mips.com>
Acked-by: Matt Redfearn <matt.redfearn@mips.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: trivial@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It seems that this is a typo error and the proper bit masking is
"RT | RS" instead of "RS | RS".
This issue was detected with the help of Coccinelle.
Fixes: d6b3314b49 ("MIPS: uasm: Add lh uam instruction")
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Reviewed-by: James Hogan <jhogan@kernel.org>
Cc: <stable@vger.kernel.org> # 3.16+
Patchwork: https://patchwork.linux-mips.org/patch/17551/
Signed-off-by: James Hogan <jhogan@kernel.org>
MIPS will soon not be a part of Imagination Technologies, and as such
many @imgtec.com email addresses will no longer be valid. This patch
updates the addresses for those who:
- Have 10 or more patches in mainline authored using an @imgtec.com
email address, or any patches dated within the past year.
- Are still with Imagination but leaving as part of the MIPS business
unit, as determined from an internal email address list.
- Haven't already updated their email address (ie. JamesH) or expressed
a desire to be excluded (ie. Maciej).
- Acked v2 or earlier of this patch, which leaves Deng-Cheng, Matt &
myself.
New addresses are of the form firstname.lastname@mips.com, and all
verified against an internal email address list. An entry is added to
.mailmap for each person such that get_maintainer.pl will report the new
addresses rather than @imgtec.com addresses which will soon be dead.
Instances of the affected addresses throughout the tree are then
mechanically replaced with the new @mips.com address.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Deng-Cheng Zhu <dengcheng.zhu@imgtec.com>
Cc: Deng-Cheng Zhu <dengcheng.zhu@mips.com>
Acked-by: Dengcheng Zhu <dengcheng.zhu@mips.com>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Matt Redfearn <matt.redfearn@mips.com>
Acked-by: Matt Redfearn <matt.redfearn@mips.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: trivial@kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/17540/
Signed-off-by: James Hogan <jhogan@kernel.org>
After we removed all the dead wood it turns out only two architectures
actually implement dma_cache_sync as a real op: mips and parisc. Add
a cache_sync method to struct dma_map_ops and implement it for the
mips defualt DMA ops, and the parisc pa11 ops.
Note that arm, arc and openrisc support DMA_ATTR_NON_CONSISTENT, but
never provided a functional dma_cache_sync implementations, which
seems somewhat odd.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
With Coherence Manager (CM) 3.5 information about the topology of the
system, which has previously only been available through & accessed from
the CM, is now also provided by the Cluster Power Controller (CPC). This
includes a new CPC_CONFIG register mirroring GCR_CONFIG, and similarly a
new CPC_Cx_CONFIG register mirroring GCR_Cx_CONFIG.
In preparation for adjusting functions such as mips_cm_numcores(), which
have previously only needed to access the CM, to also access the CPC
this patch modifies the way we use the various CPS headers. Rather than
having users include asm/mips-cm.h or asm/mips-cpc.h individually we
instead have users include asm/mips-cps.h which in turn includes
asm/mips-cm.h & asm/mips-cpc.h. This means that users will gain access
to both CM & CPC registers by including one header, and most importantly
it makes asm/mips-cps.h an ideal location for helper functions which
need to access the various components of the CPS.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17015/
Patchwork: https://patchwork.linux-mips.org/patch/17217/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Make use of the new change_*, set_* & clear_* accessor functions for CPS
(CM, CPC & GIC) registers where doing so makes the code easier to read
or shortens it without adversely affecting readability.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17005/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
There's no reason for us not to use BIT() & GENMASK() in asm/mips-cm.h
when declaring macros corresponding to register fields. This patch
modifies our definitions to do so.
The *_SHF definitions are removed entirely - they duplicate information
found in the masks, are infrequently used & can be replaced with use of
__ffs() where needed.
The *_MSK definitions then lose their _MSK suffix which is now somewhat
redundant, and users are modified to match.
The field definitions are moved to follow the appropriate register's
accessor functions, which helps to keep the field definitions in order &
to find the appropriate fields for a given register. Whilst here a
comment is added describing each register & including its name, which is
helpful both for linking the register back to hardware documentation &
for grepping purposes.
This also cleans up a couple of issues that became obvious as a result
of making the changes described above:
- We previously had definitions for GCR_Cx_RESET_EXT_BASE & a phony
copy of that named GCR_RESET_EXT_BASE - a register which does not
exist. The bad definitions were added by commit 497e803ebf ("MIPS:
smp-cps: Ensure secondary cores start with EVA disabled") and made
use of from boot_core(), which is now modified to use the
GCR_Cx_RESET_EXT_BASE definitions.
- We had a typo in CM_GCR_ERROR_CAUSE_ERRINGO_MSK - we now correctly
define this as inFo rather than inGo.
Now that we don't duplicate field information between _SHF & _MSK
definitions, and keep the fields next to the register accessors, it will
be much easier to spot & prevent any similar oddities being introduced
in the future.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17001/
Patchwork: https://patchwork.linux-mips.org/patch/17216/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We currently have various variables & functions which are only used
within a single translation unit, but which we don't declare static.
This causes various sparse warnings of the form:
arch/mips/kernel/mips-r2-to-r6-emul.c:49:1: warning: symbol
'mipsr2emustats' was not declared. Should it be static?
arch/mips/kernel/unaligned.c:1381:11: warning: symbol 'reg16to32st'
was not declared. Should it be static?
arch/mips/mm/mmap.c:146:15: warning: symbol 'arch_mmap_rnd' was not
declared. Should it be static?
Fix these & others by declaring various affected variables & functions
static, avoiding the sparse warnings & redundant symbols.
[ralf@linux-mips.org: Add Marcin's build fix.]
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: trivial@kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/17176/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
arch/mips/mm/init.c provides our implementation of free_initrd_mem(),
but doesn't include the linux/initrd.h header which declares them. This
leads to a warning from sparse:
arch/mips/mm/init.c:501:6: warning: symbol 'free_initrd_mem' was not
declared. Should it be static?
Fix this by including linux/initrd.h to get the declaration of
free_initrd_mem().
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: trivial@kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/17172/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
arch/mips/mm/mmap.c provides our implementations of the arch_mmap_rnd()
& arch_randomize_brk() functions, but doesn't include the
linux/elf-randomize.h header which declares them. This leads to warnings
from sparse:
arch/mips/mm/mmap.c:146:15: warning: symbol 'arch_mmap_rnd' was not
declared. Should it be static?
arch/mips/mm/mmap.c:190:15: warning: symbol 'arch_randomize_brk' was
not declared. Should it be static?
Fix this by including linux/elf-randomize.h to get the declarations of
arch_mmap_rnd() & arch_randomize_brk().
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: trivial@kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/17171/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
arch/mips/mm/cache.c provides our implementation of the cpu_cache_init()
function, but doesn't include the asm/setup.h header which declares it.
This leads to a warning from sparse:
arch/mips/mm/cache.c:274:6: warning: symbol 'cpu_cache_init' was not
declared. Should it be static?
Fix this by including asm/setup.h to get the declaration of
cpu_cache_init().
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: trivial@kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/17168/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Besides eliminating lots of duplication this also allows allocations with
the DMA_ATTR_NON_CONSISTENT to use the CMA allocator.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17181/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The kernel contains a small amount of incomplete code aimed at
supporting old R6000 CPUs. This is:
- Unused, as no machine selects CONFIG_SYS_HAS_CPU_R6000.
- Broken, since there are glaring errors such as r6000_fpu.S moving
the FCSR register to t1, then ignoring it & instead saving t0 into
struct sigcontext...
- A maintenance headache, since it's code that nobody can test which
nevertheless imposes constraints on code which it shares with other
machines.
Remove this incomplete & broken R6000 CPU support in order to clean up
and in preparation for changes which will no longer need to consider
dragging the pretense of R6000 support along with them.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16236/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Christoph noticed [1] that default DMA pool in current form overload
the DMA coherent infrastructure. In reply, Robin suggested [2] to
split the per-device vs. global pool interfaces, so allocation/release
from default DMA pool is driven by dma ops implementation.
This patch implements Robin's idea and provide interface to
allocate/release/mmap the default (aka global) DMA pool.
To make it clear that existing *_from_coherent routines work on
per-device pool rename them to *_from_dev_coherent.
[1] https://lkml.org/lkml/2017/7/7/370
[2] https://lkml.org/lkml/2017/7/7/431
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Suggested-by: Robin Murphy <robin.murphy@arm.com>
Tested-by: Andras Szemzo <sza@esh.hu>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Pull MIPS updates from Ralf Baechle:
"Boston platform support:
- Document DT bindings
- Add CLK driver for board clocks
CM:
- Avoid per-core locking with CM3 & higher
- WARN on attempt to lock invalid VP, not BUG
CPS:
- Select CONFIG_SYS_SUPPORTS_SCHED_SMT for MIPSr6
- Prevent multi-core with dcache aliasing
- Handle cores not powering down more gracefully
- Handle spurious VP starts more gracefully
DSP:
- Add lwx & lhx missaligned access support
eBPF:
- Add MIPS support along with many supporting change to add the
required infrastructure
Generic arch code:
- Misc sysmips MIPS_ATOMIC_SET fixes
- Drop duplicate HAVE_SYSCALL_TRACEPOINTS
- Negate error syscall return in trace
- Correct forced syscall errors
- Traced negative syscalls should return -ENOSYS
- Allow samples/bpf/tracex5 to access syscall arguments for sane
traces
- Cleanup from old Kconfig options in defconfigs
- Fix PREF instruction usage by memcpy for MIPS R6
- Fix various special cases in the FPU eulation
- Fix some special cases in MIPS16e2 support
- Fix MIPS I ISA /proc/cpuinfo reporting
- Sort MIPS Kconfig alphabetically
- Fix minimum alignment requirement of IRQ stack as required by
ABI / GCC
- Fix special cases in the module loader
- Perform post-DMA cache flushes on systems with MAARs
- Probe the I6500 CPU
- Cleanup cmpxchg and add support for 1 and 2 byte operations
- Use queued read/write locks (qrwlock)
- Use queued spinlocks (qspinlock)
- Add CPU shared FTLB feature detection
- Handle tlbex-tlbp race condition
- Allow storing pgd in C0_CONTEXT for MIPSr6
- Use current_cpu_type() in m4kc_tlbp_war()
- Support Boston in the generic kernel
Generic platform:
- yamon-dt: Pull YAMON DT shim code out of SEAD-3 board
- yamon-dt: Support > 256MB of RAM
- yamon-dt: Use serial* rather than uart* aliases
- Abstract FDT fixup application
- Set RTC_ALWAYS_BCD to 0
- Add a MAINTAINERS entry
core kernel:
- qspinlock.c: include linux/prefetch.h
Loongson 3:
- Add support
Perf:
- Add I6500 support
SEAD-3:
- Remove GIC timer from DT
- Set interrupt-parent per-device, not at root node
- Fix GIC interrupt specifiers
SMP:
- Skip IPI setup if we only have a single CPU
VDSO:
- Make comment match reality
- Improvements to time code in VDSO"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (86 commits)
locking/qspinlock: Include linux/prefetch.h
MIPS: Fix MIPS I ISA /proc/cpuinfo reporting
MIPS: Fix minimum alignment requirement of IRQ stack
MIPS: generic: Support MIPS Boston development boards
MIPS: DTS: img: Don't attempt to build-in all .dtb files
clk: boston: Add a driver for MIPS Boston board clocks
dt-bindings: Document img,boston-clock binding
MIPS: Traced negative syscalls should return -ENOSYS
MIPS: Correct forced syscall errors
MIPS: Negate error syscall return in trace
MIPS: Drop duplicate HAVE_SYSCALL_TRACEPOINTS select
MIPS16e2: Provide feature overrides for non-MIPS16 systems
MIPS: MIPS16e2: Report ASE presence in /proc/cpuinfo
MIPS: MIPS16e2: Subdecode extended LWSP/SWSP instructions
MIPS: MIPS16e2: Identify ASE presence
MIPS: VDSO: Fix a mismatch between comment and preprocessor constant
MIPS: VDSO: Add implementation of gettimeofday() fallback
MIPS: VDSO: Add implementation of clock_gettime() fallback
MIPS: VDSO: Fix conversions in do_monotonic()/do_monotonic_coarse()
MIPS: Use current_cpu_type() in m4kc_tlbp_war()
...
A poisoned or migrated hugepage is stored as a swap entry in the page
tables. On architectures that support hugepages consisting of
contiguous page table entries (such as on arm64) this leads to ambiguity
in determining the page table entry to return in huge_pte_offset() when
a poisoned entry is encountered.
Let's remove the ambiguity by adding a size parameter to convey
additional information about the requested address. Also fixup the
definition/usage of huge_pte_offset() throughout the tree.
Link: http://lkml.kernel.org/r/20170522133604.11392-4-punit.agrawal@arm.com
Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
Acked-by: Steve Capper <steve.capper@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: James Hogan <james.hogan@imgtec.com> (odd fixer:METAG ARCHITECTURE)
Cc: Ralf Baechle <ralf@linux-mips.org> (supporter:MIPS)
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Rich Felker <dalias@libc.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: "Aneesh Kumar K.V" <aneesh.kumar@linux.vnet.ibm.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Hillf Danton <hillf.zj@alibaba-inc.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Recent CPUs from Imagination Technologies such as the I6400 or P6600 are
able to speculatively fetch data from memory into caches. This means
that if used in a system with non-coherent DMA they require that caches
be invalidated after a device performs DMA, and before the CPU reads the
DMA'd data, in order to ensure that stale values weren't speculatively
prefetched.
Such CPUs also introduced Memory Accessibility Attribute Registers
(MAARs) in order to control the regions in which they are allowed to
speculate. Thus we can use the presence of MAARs as a good indication
that the CPU requires the above cache maintenance. Use the presence of
MAARs to determine the result of cpu_needs_post_dma_flush() in the
default case, in order to handle these recent CPUs correctly.
Note that the return type of cpu_needs_post_dma_flush() is changed to
bool, such that it's clearer what's happening when cpu_has_maar is cast
to bool for the return value. If this patch were backported to a
pre-v4.7 kernel then MIPS_CPU_MAAR was 1ull<<34, so when cast to an int
we would incorrectly return 0. It so happens that MIPS_CPU_MAAR is
currently 1ull<<30, so when truncated to an int gives a non-zero value
anyway, but even so the implicit conversion from long long int to bool
makes it clearer to understand what will happen than the implicit
conversion from long long int to int would. The bool return type also
fits this usage better semantically, so seems like an all-round win.
Thanks to Ed for spotting the issue for pre-v4.7 kernels & suggesting
the return type change.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Tested-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Cc: Ed Blake <ed.blake@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16363/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Use current_cpu_type() to check for 4Kc processors instead of checking
the PRID directly. This will allow for the 4Kc case to be optimised out
of kernels that can't run on 4KC processors, thanks to __get_cpu_type()
and its unreachable() call.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16205/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
In systems where there are multiple actors updating the TLB, the
potential exists for a race condition wherein a CPU hits a TLB exception
but by the time it reaches a TLBP instruction the affected TLB entry may
have been replaced. This can happen if, for example, a CPU shares the
TLB between hardware threads (VPs) within a core and one of them
replaces the entry that another has just taken a TLB exception for.
We handle this race in the case of the Hardware Table Walker (HTW) being
the other actor already, but didn't take into account the potential for
multiple threads racing. Include the code for aborting TLB exception
handling in affected multi-threaded systems, those being the I6400 &
I6500 CPUs which share TLB entries between VPs.
In the case of using RiXi without dedicated exceptions we have never
handled this race even for HTW. This patch adds WARN()s to these cases
which ought never to be hit because all CPUs with either HTW or shared
FTLB RAMs also include dedicated RiXi exceptions, but the WARN()s will
ensure this is always the case.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16203/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Introduce the I6500 PRID & probe it just the same way as I6400. The MIPS
I6500 is the latest in Imagination Technologies' I-Class range of CPUs,
with a focus on scalability & heterogeneity. It introduces the notion of
multiple clusters to the MIPS Coherent Processing System, allowing for a
far higher total number of cores & threads in a system when compared
with its predecessors. Clusters don't need to be identical, and may
contain differing numbers of cores & IOCUs, or cores with differing
properties.
This patch alone adds the basic support for booting Linux on an I6500
CPU without support for any of its new functionality, for which support
will be introduced in further patches.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16190/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Recent CPUs from Imagination Technologies such as the I6400 or P6600 are
able to speculatively fetch data from memory into caches. This means
that if used in a system with non-coherent DMA they require that caches
be invalidated after a device performs DMA, and before the CPU reads the
DMA'd data, in order to ensure that stale values weren't speculatively
prefetched.
Such CPUs also introduced Memory Accessibility Attribute Registers
(MAARs) in order to control the regions in which they are allowed to
speculate. Thus we can use the presence of MAARs as a good indication
that the CPU requires the above cache maintenance. Use the presence of
MAARs to determine the result of cpu_needs_post_dma_flush() in the
default case, in order to handle these recent CPUs correctly.
Note that the return type of cpu_needs_post_dma_flush() is changed to
bool, such that it's clearer what's happening when cpu_has_maar is cast
to bool for the return value. If this patch were backported to a
pre-v4.7 kernel then MIPS_CPU_MAAR was 1ull<<34, so when cast to an int
we would incorrectly return 0. It so happens that MIPS_CPU_MAAR is
currently 1ull<<30, so when truncated to an int gives a non-zero value
anyway, but even so the implicit conversion from long long int to bool
makes it clearer to understand what will happen than the implicit
conversion from long long int to int would. The bool return type also
fits this usage better semantically, so seems like an all-round win.
Thanks to Ed for spotting the issue for pre-v4.7 kernels & suggesting
the return type change.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Tested-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Cc: Ed Blake <ed.blake@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16363/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Instead of doing a linear search through the insn_table for each
instruction, use the opcode as direct index into the table. This will
give constant time lookup performance as the number of supported
opcodes increases. Make the tables const as they are only ever read.
For uasm-mips.c sort the table alphabetically, and remove duplicate
entries, uasm-micromips.c was already sorted and duplicate free.
There is a small savings in object size as struct insn loses a field:
$ size arch/mips/mm/uasm-mips.o arch/mips/mm/uasm-mips.o.save
text data bss dec hex filename
10040 0 0 10040 2738 arch/mips/mm/uasm-mips.o
9240 1120 0 10360 2878 arch/mips/mm/uasm-mips.o.save
Signed-off-by: David Daney <david.daney@cavium.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16365/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Stack guard page is a useful feature to reduce a risk of stack smashing
into a different mapping. We have been using a single page gap which
is sufficient to prevent having stack adjacent to a different mapping.
But this seems to be insufficient in the light of the stack usage in
userspace. E.g. glibc uses as large as 64kB alloca() in many commonly
used functions. Others use constructs liks gid_t buffer[NGROUPS_MAX]
which is 256kB or stack strings with MAX_ARG_STRLEN.
This will become especially dangerous for suid binaries and the default
no limit for the stack size limit because those applications can be
tricked to consume a large portion of the stack and a single glibc call
could jump over the guard page. These attacks are not theoretical,
unfortunatelly.
Make those attacks less probable by increasing the stack guard gap
to 1MB (on systems with 4k pages; but make it depend on the page size
because systems with larger base pages might cap stack allocations in
the PAGE_SIZE units) which should cover larger alloca() and VLA stack
allocations. It is obviously not a full fix because the problem is
somehow inherent, but it should reduce attack space a lot.
One could argue that the gap size should be configurable from userspace,
but that can be done later when somebody finds that the new 1MB is wrong
for some special case applications. For now, add a kernel command line
option (stack_guard_gap) to specify the stack gap size (in page units).
Implementation wise, first delete all the old code for stack guard page:
because although we could get away with accounting one extra page in a
stack vma, accounting a larger gap can break userspace - case in point,
a program run with "ulimit -S -v 20000" failed when the 1MB gap was
counted for RLIMIT_AS; similar problems could come with RLIMIT_MLOCK
and strict non-overcommit mode.
Instead of keeping gap inside the stack vma, maintain the stack guard
gap as a gap between vmas: using vm_start_gap() in place of vm_start
(or vm_end_gap() in place of vm_end if VM_GROWSUP) in just those few
places which need to respect the gap - mainly arch_get_unmapped_area(),
and and the vma tree's subtree_gap support for that.
Original-patch-by: Oleg Nesterov <oleg@redhat.com>
Original-patch-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Hugh Dickins <hughd@google.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Tested-by: Helge Deller <deller@gmx.de> # parisc
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
fixrange_init operates at PMD-granularity and expects the addresses to
be PMD-size aligned, but currently that might not be the case for
PKMAP_BASE unless it is defined properly, so ensure a correct alignment
is used before passing the address to fixrange_init.
fixed mappings: only align the start address that is passed to
fixrange_init rather than the value before adding the size, as we may
end up with uninitialised upper part of the range.
Signed-off-by: Marcin Nowakowski <marcin.nowakowski@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/15948/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
support; virtual interrupt controller performance improvements; support
for userspace virtual interrupt controller (slower, but necessary for
KVM on the weird Broadcom SoCs used by the Raspberry Pi 3)
* MIPS: basic support for hardware virtualization (ImgTec
P5600/P6600/I6400 and Cavium Octeon III)
* PPC: in-kernel acceleration for VFIO
* s390: support for guests without storage keys; adapter interruption
suppression
* x86: usual range of nVMX improvements, notably nested EPT support for
accessed and dirty bits; emulation of CPL3 CPUID faulting
* generic: first part of VCPU thread request API; kvm_stat improvements
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJZEHUkAAoJEL/70l94x66DBeYH/09wrpJ2FjU4Rqv7FxmqgWfH
9WGi4wvn/Z+XzQSyfMJiu2SfZVzU69/Y67OMHudy7vBT6knB+ziM7Ntoiu/hUfbG
0g5KsDX79FW15HuvuuGh9kSjUsj7qsQdyPZwP4FW/6ZoDArV9mibSvdjSmiUSMV/
2wxaoLzjoShdOuCe9EABaPhKK0XCrOYkygT6Paz1pItDxaSn8iW3ulaCuWMprUfG
Niq+dFemK464E4yn6HVD88xg5j2eUM6bfuXB3qR3eTR76mHLgtwejBzZdDjLG9fk
32PNYKhJNomBxHVqtksJ9/7cSR6iNPs7neQ1XHemKWTuYqwYQMlPj1NDy0aslQU=
=IsiZ
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Paolo Bonzini:
"ARM:
- HYP mode stub supports kexec/kdump on 32-bit
- improved PMU support
- virtual interrupt controller performance improvements
- support for userspace virtual interrupt controller (slower, but
necessary for KVM on the weird Broadcom SoCs used by the Raspberry
Pi 3)
MIPS:
- basic support for hardware virtualization (ImgTec P5600/P6600/I6400
and Cavium Octeon III)
PPC:
- in-kernel acceleration for VFIO
s390:
- support for guests without storage keys
- adapter interruption suppression
x86:
- usual range of nVMX improvements, notably nested EPT support for
accessed and dirty bits
- emulation of CPL3 CPUID faulting
generic:
- first part of VCPU thread request API
- kvm_stat improvements"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (227 commits)
kvm: nVMX: Don't validate disabled secondary controls
KVM: put back #ifndef CONFIG_S390 around kvm_vcpu_kick
Revert "KVM: Support vCPU-based gfn->hva cache"
tools/kvm: fix top level makefile
KVM: x86: don't hold kvm->lock in KVM_SET_GSI_ROUTING
KVM: Documentation: remove VM mmap documentation
kvm: nVMX: Remove superfluous VMX instruction fault checks
KVM: x86: fix emulation of RSM and IRET instructions
KVM: mark requests that need synchronization
KVM: return if kvm_vcpu_wake_up() did wake up the VCPU
KVM: add explicit barrier to kvm_vcpu_kick
KVM: perform a wake_up in kvm_make_all_cpus_request
KVM: mark requests that do not need a wakeup
KVM: remove #ifndef CONFIG_S390 around kvm_vcpu_wake_up
KVM: x86: always use kvm_make_request instead of set_bit
KVM: add kvm_{test,clear}_request to replace {test,clear}_bit
s390: kvm: Cpu model support for msa6, msa7 and msa8
KVM: x86: remove irq disablement around KVM_SET_CLOCK/KVM_GET_CLOCK
kvm: better MWAIT emulation for guests
KVM: x86: virtualize cpuid faulting
...
Commit 41c594ab65 ("[MIPS] MT: Improved multithreading support.")
added an else case to an if statement in do_page_fault() (which has
since gained 2 leading underscores) for some unclear reason. If the
condition in the if statement evaluates true then we execute a goto &
branch elsewhere anyway, so the else has no effect. Combined with an #if
0 block with misleading indentation introduced in the same commit it
makes the code less clear than it could be.
Remove the unnecessary else statement & de-indent the printk within
the #if 0 block in order to make the code easier for humans to parse.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: trivial@kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/15842/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We always either target MIPS32/MIPS64 or microMIPS, and always include
one & only one of uasm-mips.c or uasm-micromips.c. Therefore the
abstraction of the ISA in asm/uasm.h declaring functions for either ISA
is redundant & needless. Remove it to simplify the code.
This is largely the result of the following:
:%s/ISAOPC(\(.\{-}\))/uasm_i##\1/
:%s/ISAFUNC(\(.\{-}\))/\1/
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Paul Burton <paul.burton@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/15844/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Some users must have 4K pages while needing a 48-bit VA space size.
The cleanest way do do this is to go to a 4-level page table for this
case. Each page table level using order-0 pages adds 9 bits to the
VA size (at 4K pages, so for four levels we get 9 * 4 + 12 == 48-bits.
For the 4K page size case only we add support functions for the PUD
level of the page table tree, also the TLB exception handlers get an
extra level of tree walk.
[david.daney@cavium.com: Forward port to v4.10.]
[david.daney@cavium.com: Forward port to v4.11.]
Signed-off-by: Alex Belits <alex.belits@cavium.com>
Signed-off-by: David Daney <david.daney@cavium.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Alex Belits <alex.belits@cavium.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/15312/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cache management is implemented separately for Cavium Octeon CPUs, so
r4k_blast_[id]cache aren't available. Instead for Octeon perform a local
icache flush using local_flush_icache_range(), and for other platforms
which don't use c-r4k.c use __flush_cache_all() / flush_icache_all().
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: David Daney <david.daney@cavium.com>
Cc: Andreas Herrmann <andreas.herrmann@caviumnetworks.com>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
The MAAR V bit has been renamed VL since another bit called VH is added
at the top of the register when it is extended to 64-bits on a 32-bit
processor with XPA. Rename the V definition, fix the various users, and
add definitions for the VH bit. Also add a definition for the MAARI
Index field.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
If scache.waysize is 0, r4k___flush_cache_all() will do nothing and
then cause bugs. BTW, though vcache.waysize isn't being used by now,
we also fix its calculation.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Cc: John Crispin <john@phrozen.org>
Cc: Steven J . Hill <Steven.Hill@caviumnetworks.com>
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: stable@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/15756/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
On VTLB+FTLB platforms (such as Loongson-3A R2), FTLB's pagesize is
usually configured the same as PAGE_SIZE. In such a case, Huge page
entry is not suitable to write in FTLB.
Unfortunately, when a huge page is created, its page table entries
haven't created immediately. Then the TLB refill handler will fetch an
invalid page table entry which has no "HUGE" bit, and this entry may be
written to FTLB. Since it is invalid, TLB load/store handler will then
use tlbwi to write the valid entry at the same place. However, the
valid entry is a huge page entry which isn't suitable for FTLB.
Our solution is to modify build_huge_handler_tail. Flush the invalid
old entry (whether it is in FTLB or VTLB, this is in order to reduce
branches) and use tlbwr to write the valid new entry.
Signed-off-by: Rui Wang <wangr@lemote.com>
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Cc: John Crispin <john@phrozen.org>
Cc: Steven J . Hill <Steven.Hill@caviumnetworks.com>
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: linux-mips@linux-mips.org
Cc: stable@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/15754/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Update code that relied on sched.h including various MM types for them.
This will allow us to remove the <linux/mm_types.h> include from <linux/sched.h>.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We are going to split more MM APIs out of <linux/sched.h>, which
will have to be picked up from a couple of .c files.
The APIs that we are going to move are:
arch_pick_mmap_layout()
arch_get_unmapped_area()
arch_get_unmapped_area_topdown()
mm_update_next_owner()
Include the header in the files that are going to need it.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We are going to split <linux/sched/signal.h> out of <linux/sched.h>, which
will have to be picked up from other headers and a couple of .c files.
Create a trivial placeholder <linux/sched/signal.h> file that just
maps to <linux/sched.h> to make this patch obviously correct and
bisectable.
Include the new header in the files that are going to need it.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Bart Van Assche noted that the ib DMA mapping code was significantly
similar enough to the core DMA mapping code that with a few changes
it was possible to remove the IB DMA mapping code entirely and
switch the RDMA stack to use the core DMA mapping code. This resulted
in a nice set of cleanups, but touched the entire tree. This branch
will be submitted separately to Linus at the end of the merge window
as per normal practice for tree wide changes like this.
-----BEGIN PGP SIGNATURE-----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=e0Si
-----END PGP SIGNATURE-----
Merge tag 'for-next-dma_ops' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma DMA mapping updates from Doug Ledford:
"Drop IB DMA mapping code and use core DMA code instead.
Bart Van Assche noted that the ib DMA mapping code was significantly
similar enough to the core DMA mapping code that with a few changes it
was possible to remove the IB DMA mapping code entirely and switch the
RDMA stack to use the core DMA mapping code.
This resulted in a nice set of cleanups, but touched the entire tree
and has been kept separate for that reason."
* tag 'for-next-dma_ops' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (37 commits)
IB/rxe, IB/rdmavt: Use dma_virt_ops instead of duplicating it
IB/core: Remove ib_device.dma_device
nvme-rdma: Switch from dma_device to dev.parent
RDS: net: Switch from dma_device to dev.parent
IB/srpt: Modify a debug statement
IB/srp: Switch from dma_device to dev.parent
IB/iser: Switch from dma_device to dev.parent
IB/IPoIB: Switch from dma_device to dev.parent
IB/rxe: Switch from dma_device to dev.parent
IB/vmw_pvrdma: Switch from dma_device to dev.parent
IB/usnic: Switch from dma_device to dev.parent
IB/qib: Switch from dma_device to dev.parent
IB/qedr: Switch from dma_device to dev.parent
IB/ocrdma: Switch from dma_device to dev.parent
IB/nes: Remove a superfluous assignment statement
IB/mthca: Switch from dma_device to dev.parent
IB/mlx5: Switch from dma_device to dev.parent
IB/mlx4: Switch from dma_device to dev.parent
IB/i40iw: Remove a superfluous assignment statement
IB/hns: Switch from dma_device to dev.parent
...
The callers of the DMA alloc functions already provide the proper
context GFP flags. Make sure to pass them through to the CMA allocator,
to make the CMA compaction context aware.
Link: http://lkml.kernel.org/r/20170127172328.18574-3-l.stach@pengutronix.de
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Radim Krcmar <rkrcmar@redhat.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Alexander Graf <agraf@suse.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
MIPS dependencies for KVM
Miscellaneous MIPS architecture changes depended on by the MIPS KVM
changes in the KVM tree.
- Move pgd_alloc() out of header.
- Exports so KVM can access page table management and TLBEX functions.
- Add return errors to protected cache ops.
Export to TLB exception code generating functions so that KVM can
construct a fast TLB refill handler for guest context without
reinventing the wheel quite so much.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Export pmd_init(), invalid_pmd_table and tlbmiss_handler_setup_pgd to
GPL kernel modules so that MIPS KVM can use the inline page table
management functions and switch between page tables:
- pmd_init() will be used directly by KVM to initialise newly allocated
pmd tables with invalid lower level table pointers.
- invalid_pmd_table is used by pud_present(), pud_none(), and
pud_clear(), which KVM will use to test and clear pud entries.
- tlbmiss_handler_setup_pgd() will be called by KVM entry code to switch
to the appropriate GVA page tables.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
pgd_alloc() references init_mm which is not exported to modules. In
order for KVM to be able to use pgd_alloc() to allocate GVA page tables,
move pgd_alloc() into a new pgtable.c file and export it to modules.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
In systems with CM3 & higher, the L2 cache is inclusive of the L1
dcache. Indicate this such that cpu_has_inclusive_pcaches evaluates true
and we avoid some unnecessary cache ops during DMA cache maintenance.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14018/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Physically indexed caches cannot suffer from virtual aliasing, so clear
the MIPS_CACHE_ALIASES bit in order to ensure we don't do extra work
avoiding aliasing that cannot happen.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14017/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The L1 data cache in I6400 CPUs is indexed by physical address bits if
an entry for the address is present in the DTLB early enough in the
pipelined execution of a memory access instruction. If an entry is not
present then it's indexed by virtual address bits, but hardware will
check in a later pipeline stage when a DTLB entry has been created
whether the virtual address bits used match the physical address bits,
and if not will transparently restart the memory access instruction.
This means that although it isn't always physically indexed, it appears
so to software & we can treat the I6400 L1 data cache as being
physically indexed in order to avoid considering aliasing.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14016/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Now that EXPORT_SYMBOL can be used from assembly source, move the
EXPORT_SYMBOL invocations for the copy_page & clear_page functions to be
alongside their definitions.
With this change there are no longer any symbols exported from
mips_ksyms.c so remove the file.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14515/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
It's unclear to me why this wasn't always the case, but move the
EXPORT_SYMBOL invocation for invalid_pte_table to be alongside its
definition.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14511/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When generating TLB exception handling code we write to memory reserved
at the handle_tlbl, handle_tlbm & handle_tlbs symbols. Up until now the
ISA bit has always been clear simply because the assembly code reserving
the space for those functions places no instructions in them. In
preparation for marking all LEAF functions as containing code,
explicitly clear the ISA bit when calculating the addresses at which to
write TLB exception handling code.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14507/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
arch_mmap_rnd() uses hard-coded limits of 16MB for the randomisation
of mmap within 32bit processes and 256MB in 64bit processes. Since v4.4
other arches support tuning this value in /proc/sys/vm/mmap_rnd_bits.
Add support for this to MIPS.
Set the minimum(default) number of bits randomisation for 32bit to 8 -
which with 4k pagesize is unchanged from the current 16MB total
randomness. The minimum(default) for 64bit is 12bits, again with 4k
pagesize this is the same as the current 256MB.
This patch is necessary for MIPS32 to pass the Android CTS tests, with
the number of random bits set to 15.
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Daniel Cashman <dcashman@android.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: linux-mips@linux-mips.org
Cc: kernel-hardening@lists.openwall.com
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14617/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fix the following build error with binutils 2.25.
CC arch/mips/mm/sc-ip22.o
{standard input}: Assembler messages:
{standard input}:132: Error: number (0x9000000080000000) larger than 32 bits
{standard input}:159: Error: number (0x9000000080000000) larger than 32 bits
{standard input}:200: Error: number (0x9000000080000000) larger than 32 bits
scripts/Makefile.build:293: recipe for target 'arch/mips/mm/sc-ip22.o' failed
make[1]: *** [arch/mips/mm/sc-ip22.o] Error 1
MIPS has used .set mips3 to temporarily switch the assembler to 64 bit
mode in 64 bit kernels virtually forever. Binutils 2.25 broke this
behavious partially by happily accepting 64 bit instructions in .set mips3
mode but puking on 64 bit constants when generating 32 bit ELF. Binutils
2.26 restored the old behaviour again.
Fix build with binutils 2.25 by open coding the offending
dli $1, 0x9000000080000000
as
li $1, 0x9000
dsll $1, $1, 48
which is ugly be the only thing that will build on all binutils vintages.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: stable@vger.kernel.org
This was entirely automated, using the script by Al:
PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>'
sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \
$(git grep -l "$PATT"|grep -v ^include/linux/uaccess.h)
to do the replacement at the end of the merge window.
Requested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This change allows us to pass DMA_ATTR_SKIP_CPU_SYNC which allows us to
avoid invoking cache line invalidation if the driver will just handle it
via a sync_for_cpu or sync_for_device call.
Link: http://lkml.kernel.org/r/20161110113513.76501.32321.stgit@ahduyck-blue-test.jf.intel.com
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Keguang Zhang <keguang.zhang@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since commit 4bcc595ccd ("printk: reinstate KERN_CONT for printing
continuation lines") the output from __do_page_fault on MIPS has been
pretty unreadable due to the lack of KERN_CONT markers. Use pr_cont
to provide the appropriate markers & restore the expected output.
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14544/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Since MIPSr6 the Wired register is split into 2 fields, with the upper
16 bits of the register indicating a limit on the value that the wired
entry count in the bottom 16 bits of the register can take. This means
that simply reading the wired register doesn't get us a valid TLB entry
index any longer, and we instead need to retrieve only the lower 16 bits
of the register. Introduce a new num_wired_entries() function which does
this on MIPSr6 or higher and simply returns the value of the wired
register on older architecture revisions, and make use of it when
reading the number of wired entries.
Since commit e710d66683 ("MIPS: tlb-r4k: If there are wired entries,
don't use TLBINVF") we have been using a non-zero number of wired
entries to determine whether we should avoid use of the tlbinvf
instruction (which would invalidate wired entries) and instead loop over
TLB entries in local_flush_tlb_all(). This loop begins with the number
of wired entries, or before this patch some large bogus TLB index on
MIPSr6 systems. Thus since the aforementioned commit some MIPSr6 systems
with FTLBs have been prone to leaving stale address translations in the
FTLB & crashing in various weird & wonderful ways when we later observe
the wrong memory.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14557/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Merge the gup_flags cleanups from Lorenzo Stoakes:
"This patch series adjusts functions in the get_user_pages* family such
that desired FOLL_* flags are passed as an argument rather than
implied by flags.
The purpose of this change is to make the use of FOLL_FORCE explicit
so it is easier to grep for and clearer to callers that this flag is
being used. The use of FOLL_FORCE is an issue as it overrides missing
VM_READ/VM_WRITE flags for the VMA whose pages we are reading
from/writing to, which can result in surprising behaviour.
The patch series came out of the discussion around commit 38e0885465
("mm: check VMA flags to avoid invalid PROT_NONE NUMA balancing"),
which addressed a BUG_ON() being triggered when a page was faulted in
with PROT_NONE set but having been overridden by FOLL_FORCE.
do_numa_page() was run on the assumption the page _must_ be one marked
for NUMA node migration as an actual PROT_NONE page would have been
dealt with prior to this code path, however FOLL_FORCE introduced a
situation where this assumption did not hold.
See
https://marc.info/?l=linux-mm&m=147585445805166
for the patch proposal"
Additionally, there's a fix for an ancient bug related to FOLL_FORCE and
FOLL_WRITE by me.
[ This branch was rebased recently to add a few more acked-by's and
reviewed-by's ]
* gup_flag-cleanups:
mm: replace access_process_vm() write parameter with gup_flags
mm: replace access_remote_vm() write parameter with gup_flags
mm: replace __access_remote_vm() write parameter with gup_flags
mm: replace get_user_pages_remote() write/force parameters with gup_flags
mm: replace get_user_pages() write/force parameters with gup_flags
mm: replace get_vaddr_frames() write/force parameters with gup_flags
mm: replace get_user_pages_locked() write/force parameters with gup_flags
mm: replace get_user_pages_unlocked() write/force parameters with gup_flags
mm: remove write/force parameters from __get_user_pages_unlocked()
mm: remove write/force parameters from __get_user_pages_locked()
mm: remove gup_flags FOLL_WRITE games from __get_user_pages()
This removes the 'write' and 'force' use from get_user_pages_unlocked()
and replaces them with 'gup_flags' to make the use of FOLL_FORCE
explicit in callers as use of this flag can result in surprising
behaviour (and hence bugs) within the mm subsystem.
Signed-off-by: Lorenzo Stoakes <lstoakes@gmail.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Acked-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On some MIPS systems, a subset of devices may have DMA coherent with CPU
caches. For example in systems including a MIPS I/O Coherence Unit
(IOCU), some devices may be connected to that IOCU whilst others are
not.
Prior to this patch, we have a plat_device_is_coherent() function but no
implementation which does anything besides return a global true or
false, optionally chosen at runtime. For devices such as those described
above this is insufficient.
Fix this by tracking DMA coherence on a per-device basis with a
dma_coherent field in struct dev_archdata. Setting this from
arch_setup_dma_ops() takes care of devices which set the dma-coherent
property via device tree, and any PCI devices beneath a bridge described
in DT, automatically.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14349/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
There are no cases where plat_device_is_coherent() will return zero
whilst hw_coherentio is non-zero, and acting any differently in such a
case doesn't make much sense - if a device is non-coherent with the CPU
caches then access to memory "coherent" with DMA must be uncached. Clean
up the nonsensical case.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14348/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The coherentio variable has previously been used as a boolean value,
indicating whether the user specified that coherent I/O should be
enabled or disabled. It failed to take into account the case where the
user does not specify any preference, in which case it makes sense that
we should default to coherent I/O if the hardware supports it
(hw_coherentio is non-zero).
Introduce an enum to clarify the 3 different values of coherentio & use
it throughout the code, modifying plat_device_is_coherent() &
r4k_cache_init() to take into account the default case.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Paul Burton <paul.burton@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/14347/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Historically a lot of these existed because we did not have
a distinction between what was modular code and what was providing
support to modules via EXPORT_SYMBOL and friends. That changed
when we forked out support for the latter into the export.h file.
This means we should be able to reduce the usage of module.h
in code that is obj-y Makefile or bool Kconfig. The advantage
in doing so is that module.h itself sources about 15 other headers;
adding significantly to what we feed cpp, and it can obscure what
headers we are effectively using.
Since module.h was the source for init.h (for __init) and for
export.h (for EXPORT_SYMBOL) we consider each obj-y/bool instance
for the presence of either and replace as needed.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14033/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When adding a wired entry to the TLB via add_wired_entry, the tlb is
flushed with local_flush_tlb_all, which on CPUs with TLBINV results in
the new wired entry being flushed again.
Behavior of the TLBINV instruction applies to all applicable TLB entries
and is unaffected by the setting of the Wired register. Therefore if
the TLB has any wired entries, fall back to iterating over the entries
rather than blasting them all using TLBINVF.
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Ohad Ben-Cohen <ohad@wizery.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: lisa.parratt@imgtec.com
Cc: Hugh Dickins <hughd@google.com>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: linux-mips@linux-mips.org
Cc: linux-remoteproc@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14283/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
flush_icache_range() flushes icache lines in a protected fashion for
kernel addresses, however this isn't correct with EVA where protected
cache ops only operate on user addresses, making flush_icache_range()
ineffective.
Split the implementations of __flush_icache_user_range() from
flush_icache_range(), changing the normal flush_icache_range() to use
unprotected normal cache ops.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Leonid Yegoshin <leonid.yegoshin@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14156/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The cacheflush(2) system call uses flush_icache_range() to flush a range
of usermode addresses from the icache, so change it to utilise the new
__flush_icache_user_range() API to allow the more generic
flush_icache_range() to be changed to work on kernel addresses only.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Leonid Yegoshin <leonid.yegoshin@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14153/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
flush_icache_range() is used for both user addresses (i.e.
cacheflush(2)), and kernel addresses (as the API documentation
describes).
This isn't really suitable however for Enhanced Virtual Addressing (EVA)
where cache operations on usermode addresses must use a different
instruction, and the protected cache ops assume user addresses, making
flush_icache_range() ineffective on kernel addresses.
Split out a new __flush_icache_user_range() and
__local_flush_icache_user_range() for users which actually want to flush
usermode addresses (note that flush_icache_user_range() already exists
on various architectures but with different arguments).
The implementation of flush_icache_range() will be changed in an
upcoming commit to use unprotected normal cache ops so as to always work
on the kernel mode address space.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Leonid Yegoshin <leonid.yegoshin@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14152/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The EVA conditional bc_wback_inv() at the end of flush_icache_range() to
flush the modified code all the way back to RAM was apparently there for
debug purposes and to accommodate the Malta EVA configuration which
makes use of a physical alias, and didn't use the CP0_EBase.WG (Write
Gate) bit to put the exception vector in the same physical alias where
the exception vector code is written and is being flushed.
Now that CP0_EBase.WG is used, lets drop this flush.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Leonid Yegoshin <leonid.yegoshin@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14151/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
These files were only including module.h for exception table
related functions. We've now separated that content out into its
own file "extable.h" so now move over to that and avoid all the
extra header content in module.h that we don't really need to compile
these files.
In the case of traps.c we can't dump the module.h include since it is
also used to provide "print_modules".
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13934/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The paging_init() function contains code which detects that highmem is
in use but unsupported due to dcache aliasing. However this code was
ineffective because it was being run before the caches are probed,
meaning that cpu_has_dc_aliases would always evaluate to false (unless a
platform overrides it to a compile-time constant) and the detection of
the unsupported case is never triggered. The kernel would then go on to
attempt to use highmem & either hit coherency issues or trigger the
BUG_ON in flush_kernel_dcache_page().
Fix this by running paging_init() later than cpu_cache_init(), such that
the cpu_has_dc_aliases macro will evaluate correctly & the unsupported
highmem case will be detected successfully.
This then leads to a formerly hidden issue in that
mem_init_free_highmem() will attempt to free all highmem pages, even
though we're avoiding use of them & don't have valid page structs for
them. This leads to an invalid pointer dereference & a TLB exception.
Avoid this by skipping the loop in mem_init_free_highmem() if
cpu_has_dc_aliases evaluates true.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Rabin Vincent <rabinv@axis.com>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Jerome Marchand <jmarchan@redhat.com>
Cc: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: Jaedon Shin <jaedon.shin@gmail.com>
Cc: Toshi Kani <toshi.kani@hpe.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14184/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit f70ddc07b6 ("MIPS: c-r4k: Avoid small flush_icache_range SMP
calls") adds checks to force use of hit-type cache ops for small icache
flushes where they are globalised & index-type cache ops aren't, in
order to avoid the overhead of IPIs in those cases. However it
calculated the size of the region being flushed incorrectly, subtracting
the end address from the start address rather than the reverse. This
would have led to an overflow with size wrapping round to some large
value, and likely to the special case for avoiding IPIs not actually
being hit.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Fixes: f70ddc07b6 ("MIPS: c-r4k: Avoid small flush_icache_range SMP calls")
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14211/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The alignment of MIPS MAAR region addresses isn't quite right.
- It rounds an already 64 KiB aligned start address up to the next
64 KiB boundary, e.g. 0x80000000 is rounded up to 0x80010000.
- It assumes the end address is already on a 64 KiB boundary and doesn't
round it down. Should that not be the case it will hit the second
BUG_ON() in write_maar_pair().
Both cases are addressed by rounding up and down to 64 KiB boundaries in
the more traditional way of adding 0xffff (for rounding up) and masking
off the low 16 bits.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13858/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for MIPS for 4.8. Also includes is a
minor SSB cleanup as SSB code traditionally is merged through the MIPS
tree:
ATH25:
- MIPS: Add default configuration for ath25
Boot:
- For zboot, copy appended dtb to the end of the kernel
- store the appended dtb address in a variable
BPF:
- Fix off by one error in offset allocation
Cobalt code:
- Fix typos
Core code:
- debugfs_create_file returns NULL on error, so don't use IS_ERR for
testing for errors.
- Fix double locking issue in RM7000 S-cache code. This would only
affect RM7000 ARC systems on reboot.
- Fix page table corruption on THP permission changes.
- Use compat_sys_keyctl for 32 bit userspace on 64 bit kernels.
David says, there are no compatibility issues raised by this fix.
- Move some signal code around.
- Rewrite r4k count/compare clockevent device registration such that
min_delta_ticks/max_delta_ticks files are guaranteed to be
initialized.
- Only register r4k count/compare as clockevent device if we can
assume the clock to be constant.
- Fix MSA asm warnings in control reg accessors
- uasm and tlbex fixes and tweaking.
- Print segment physical address when EU=1.
- Define AT_VECTOR_SIZE_ARCH for ARCH_DLINFO.
- CP: Allow booting by VP other than VP 0
- Cache handling fixes and optimizations for r4k class caches
- Add hotplug support for R6 processors
- Cleanup hotplug bits in kconfig
- traps: return correct si code for accessing nonmapped addresses
- Remove cpu_has_safe_index_cacheops
Lantiq:
- Register IRQ handler for virtual IRQ number
- Fix EIU interrupt loading code
- Use the real EXIN count
- Fix build error.
Loongson 3:
- Increase HPET_MIN_PROG_DELTA and decrease HPET_MIN_CYCLES
Octeon:
- Delete built-in DTB pruning code for D-Link DSR-1000N.
- Clean up GPIO definitions in dlink_dsr-1000n.dts.
- Add more LEDs to the DSR-100n DTS
- Fix off by one in octeon_irq_gpio_map()
- Typo fixes
- Enable SATA by default in cavium_octeon_defconfig
- Support readq/writeq()
- Remove forced mappings of USB interrupts.
- Ensure DMA descriptors are always in the low 4GB
- Improve USB reset code for OCTEON II.
Pistachio:
- Add maintainers entry for pistachio SoC Support
- Remove plat_setup_iocoherency
Ralink:
- Fix pwm UART in spis group pinmux.
SSB:
- Change bare unsigned to unsigned int to suit coding style
Tools:
- Fix reloc tool compiler warnings.
Other:
- Delete use of ARCH_WANT_OPTIONAL_GPIOLIB"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (61 commits)
MIPS: mm: Fix definition of R6 cache instruction
MIPS: tools: Fix relocs tool compiler warnings
MIPS: Cobalt: Fix typo
MIPS: Octeon: Fix typo
MIPS: Lantiq: Fix build failure
MIPS: Use CPHYSADDR to implement mips32 __pa
MIPS: Octeon: Dlink_dsr-1000n.dts: add more leds.
MIPS: Octeon: Clean up GPIO definitions in dlink_dsr-1000n.dts.
MIPS: Octeon: Delete built-in DTB pruning code for D-Link DSR-1000N.
MIPS: store the appended dtb address in a variable
MIPS: ZBOOT: copy appended dtb to the end of the kernel
MIPS: ralink: fix spis group pinmux
MIPS: Factor o32 specific code into signal_o32.c
MIPS: non-exec stack & heap when non-exec PT_GNU_STACK is present
MIPS: Use per-mm page to execute branch delay slot instructions
MIPS: Modify error handling
MIPS: c-r4k: Use SMP calls for CM indexed cache ops
MIPS: c-r4k: Avoid small flush_icache_range SMP calls
MIPS: c-r4k: Local flush_icache_range cache op override
MIPS: c-r4k: Split r4k_flush_kernel_vmap_range()
...
The dma-mapping core and the implementations do not change the DMA
attributes passed by pointer. Thus the pointer can point to const data.
However the attributes do not have to be a bitfield. Instead unsigned
long will do fine:
1. This is just simpler. Both in terms of reading the code and setting
attributes. Instead of initializing local attributes on the stack
and passing pointer to it to dma_set_attr(), just set the bits.
2. It brings safeness and checking for const correctness because the
attributes are passed by value.
Semantic patches for this change (at least most of them):
virtual patch
virtual context
@r@
identifier f, attrs;
@@
f(...,
- struct dma_attrs *attrs
+ unsigned long attrs
, ...)
{
...
}
@@
identifier r.f;
@@
f(...,
- NULL
+ 0
)
and
// Options: --all-includes
virtual patch
virtual context
@r@
identifier f, attrs;
type t;
@@
t f(..., struct dma_attrs *attrs);
@@
identifier r.f;
@@
f(...,
- NULL
+ 0
)
Link: http://lkml.kernel.org/r/1468399300-5399-2-git-send-email-k.kozlowski@samsung.com
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Hans-Christian Noren Egtvedt <egtvedt@samfundet.no>
Acked-by: Mark Salter <msalter@redhat.com> [c6x]
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com> [cris]
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> [drm]
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Joerg Roedel <jroedel@suse.de> [iommu]
Acked-by: Fabien Dessenne <fabien.dessenne@st.com> [bdisp]
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com> [vb2-core]
Acked-by: David Vrabel <david.vrabel@citrix.com> [xen]
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> [xen swiotlb]
Acked-by: Joerg Roedel <jroedel@suse.de> [iommu]
Acked-by: Richard Kuo <rkuo@codeaurora.org> [hexagon]
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org> [m68k]
Acked-by: Gerald Schaefer <gerald.schaefer@de.ibm.com> [s390]
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Hans-Christian Noren Egtvedt <egtvedt@samfundet.no> [avr32]
Acked-by: Vineet Gupta <vgupta@synopsys.com> [arc]
Acked-by: Robin Murphy <robin.murphy@arm.com> [arm64 and dma-iommu]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The use of config_enabled() against config options is ambiguous. In
practical terms, config_enabled() is equivalent to IS_BUILTIN(), but the
author might have used it for the meaning of IS_ENABLED(). Using
IS_ENABLED(), IS_BUILTIN(), IS_MODULE() etc. makes the intention
clearer.
This commit replaces config_enabled() with IS_ENABLED() where possible.
This commit is only touching bool config options.
I noticed two cases where config_enabled() is used against a tristate
option:
- config_enabled(CONFIG_HWMON)
[ drivers/net/wireless/ath/ath10k/thermal.c ]
- config_enabled(CONFIG_BACKLIGHT_CLASS_DEVICE)
[ drivers/gpu/drm/gma500/opregion.c ]
I did not touch them because they should be converted to IS_BUILTIN()
in order to keep the logic, but I was not sure it was the authors'
intention.
Link: http://lkml.kernel.org/r/1465215656-20569-1-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: Stas Sergeev <stsp@list.ru>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Joshua Kinard <kumba@gentoo.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: "Dmitry V. Levin" <ldv@altlinux.org>
Cc: yu-cheng yu <yu-cheng.yu@intel.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Will Drewry <wad@chromium.org>
Cc: Nikolay Martynov <mar.kolya@gmail.com>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: Rafal Milecki <zajec5@gmail.com>
Cc: James Cowgill <James.Cowgill@imgtec.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Alex Smith <alex.smith@imgtec.com>
Cc: Adam Buchbinder <adam.buchbinder@gmail.com>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Mikko Rapeli <mikko.rapeli@iki.fi>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Hidehiro Kawai <hidehiro.kawai.ez@hitachi.com>
Cc: "Luis R. Rodriguez" <mcgrof@do-not-panic.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Roland McGrath <roland@hack.frob.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Tony Wu <tung7970@gmail.com>
Cc: Huaitong Han <huaitong.han@intel.com>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Juergen Gross <jgross@suse.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Andrea Gelmini <andrea.gelmini@gelma.net>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Rabin Vincent <rabin@rab.in>
Cc: "Maciej W. Rozycki" <macro@imgtec.com>
Cc: David Daney <david.daney@cavium.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge yet more updates from Andrew Morton:
- the rest of ocfs2
- various hotfixes, mainly MM
- quite a bit of misc stuff - drivers, fork, exec, signals, etc.
- printk updates
- firmware
- checkpatch
- nilfs2
- more kexec stuff than usual
- rapidio updates
- w1 things
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (111 commits)
ipc: delete "nr_ipc_ns"
kcov: allow more fine-grained coverage instrumentation
init/Kconfig: add clarification for out-of-tree modules
config: add android config fragments
init/Kconfig: ban CONFIG_LOCALVERSION_AUTO with allmodconfig
relay: add global mode support for buffer-only channels
init: allow blacklisting of module_init functions
w1:omap_hdq: fix regression
w1: add helper macro module_w1_family
w1: remove need for ida and use PLATFORM_DEVID_AUTO
rapidio/switches: add driver for IDT gen3 switches
powerpc/fsl_rio: apply changes for RIO spec rev 3
rapidio: modify for rev.3 specification changes
rapidio: change inbound window size type to u64
rapidio/idt_gen2: fix locking warning
rapidio: fix error handling in mbox request/release functions
rapidio/tsi721_dma: advance queue processing from transfer submit call
rapidio/tsi721: add messaging mbox selector parameter
rapidio/tsi721: add PCIe MRRS override parameter
rapidio/tsi721_dma: add channel mask and queue size parameters
...
There was only one use of __initdata_refok and __exit_refok
__init_refok was used 46 times against 82 for __ref.
Those definitions are obsolete since commit 312b1485fb ("Introduce new
section reference annotations tags: __ref, __refdata, __refconst")
This patch removes the following compatibility definitions and replaces
them treewide.
/* compatibility defines */
#define __init_refok __ref
#define __initdata_refok __refdata
#define __exit_refok __ref
I can also provide separate patches if necessary.
(One patch per tree and check in 1 month or 2 to remove old definitions)
[akpm@linux-foundation.org: coding-style fixes]
Link: http://lkml.kernel.org/r/1466796271-3043-1-git-send-email-fabf@skynet.be
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
VGIC implementation.
- s390: support for trapping software breakpoints, nested virtualization
(vSIE), the STHYI opcode, initial extensions for CPU model support.
- MIPS: support for MIPS64 hosts (32-bit guests only) and lots of cleanups,
preliminary to this and the upcoming support for hardware virtualization
extensions.
- x86: support for execute-only mappings in nested EPT; reduced vmexit
latency for TSC deadline timer (by about 30%) on Intel hosts; support for
more than 255 vCPUs.
- PPC: bugfixes.
The ugly bit is the conflicts. A couple of them are simple conflicts due
to 4.7 fixes, but most of them are with other trees. There was definitely
too much reliance on Acked-by here. Some conflicts are for KVM patches
where _I_ gave my Acked-by, but the worst are for this pull request's
patches that touch files outside arch/*/kvm. KVM submaintainers should
probably learn to synchronize better with arch maintainers, with the
latter providing topic branches whenever possible instead of Acked-by.
This is what we do with arch/x86. And I should learn to refuse pull
requests when linux-next sends scary signals, even if that means that
submaintainers have to rebase their branches.
Anyhow, here's the list:
- arch/x86/kvm/vmx.c: handle_pcommit and EXIT_REASON_PCOMMIT was removed
by the nvdimm tree. This tree adds handle_preemption_timer and
EXIT_REASON_PREEMPTION_TIMER at the same place. In general all mentions
of pcommit have to go.
There is also a conflict between a stable fix and this patch, where the
stable fix removed the vmx_create_pml_buffer function and its call.
- virt/kvm/kvm_main.c: kvm_cpu_notifier was removed by the hotplug tree.
This tree adds kvm_io_bus_get_dev at the same place.
- virt/kvm/arm/vgic.c: a few final bugfixes went into 4.7 before the
file was completely removed for 4.8.
- include/linux/irqchip/arm-gic-v3.h: this one is entirely our fault;
this is a change that should have gone in through the irqchip tree and
pulled by kvm-arm. I think I would have rejected this kvm-arm pull
request. The KVM version is the right one, except that it lacks
GITS_BASER_PAGES_SHIFT.
- arch/powerpc: what a mess. For the idle_book3s.S conflict, the KVM
tree is the right one; everything else is trivial. In this case I am
not quite sure what went wrong. The commit that is causing the mess
(fd7bacbca4, "KVM: PPC: Book3S HV: Fix TB corruption in guest exit
path on HMI interrupt", 2016-05-15) touches both arch/powerpc/kernel/
and arch/powerpc/kvm/. It's large, but at 396 insertions/5 deletions
I guessed that it wasn't really possible to split it and that the 5
deletions wouldn't conflict. That wasn't the case.
- arch/s390: also messy. First is hypfs_diag.c where the KVM tree
moved some code and the s390 tree patched it. You have to reapply the
relevant part of commits 6c22c98637, plus all of e030c1125e, to
arch/s390/kernel/diag.c. Or pick the linux-next conflict
resolution from http://marc.info/?l=kvm&m=146717549531603&w=2.
Second, there is a conflict in gmap.c between a stable fix and 4.8.
The KVM version here is the correct one.
I have pushed my resolution at refs/heads/merge-20160802 (commit
3d1f53419842) at git://git.kernel.org/pub/scm/virt/kvm/kvm.git.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJXoGm7AAoJEL/70l94x66DugQIAIj703ePAFepB/fCrKHkZZia
SGrsBdvAtNsOhr7FQ5qvvjLxiv/cv7CymeuJivX8H+4kuUHUllDzey+RPHYHD9X7
U6n1PdCH9F15a3IXc8tDjlDdOMNIKJixYuq1UyNZMU6NFwl00+TZf9JF8A2US65b
x/41W98ilL6nNBAsoDVmCLtPNWAqQ3lajaZELGfcqRQ9ZGKcAYOaLFXHv2YHf2XC
qIDMf+slBGSQ66UoATnYV2gAopNlWbZ7n0vO6tE2KyvhHZ1m399aBX1+k8la/0JI
69r+Tz7ZHUSFtmlmyByi5IAB87myy2WQHyAPwj+4vwJkDGPcl0TrupzbG7+T05Y=
=42ti
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Paolo Bonzini:
- ARM: GICv3 ITS emulation and various fixes. Removal of the
old VGIC implementation.
- s390: support for trapping software breakpoints, nested
virtualization (vSIE), the STHYI opcode, initial extensions
for CPU model support.
- MIPS: support for MIPS64 hosts (32-bit guests only) and lots
of cleanups, preliminary to this and the upcoming support for
hardware virtualization extensions.
- x86: support for execute-only mappings in nested EPT; reduced
vmexit latency for TSC deadline timer (by about 30%) on Intel
hosts; support for more than 255 vCPUs.
- PPC: bugfixes.
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (302 commits)
KVM: PPC: Introduce KVM_CAP_PPC_HTM
MIPS: Select HAVE_KVM for MIPS64_R{2,6}
MIPS: KVM: Reset CP0_PageMask during host TLB flush
MIPS: KVM: Fix ptr->int cast via KVM_GUEST_KSEGX()
MIPS: KVM: Sign extend MFC0/RDHWR results
MIPS: KVM: Fix 64-bit big endian dynamic translation
MIPS: KVM: Fail if ebase doesn't fit in CP0_EBase
MIPS: KVM: Use 64-bit CP0_EBase when appropriate
MIPS: KVM: Set CP0_Status.KX on MIPS64
MIPS: KVM: Make entry code MIPS64 friendly
MIPS: KVM: Use kmap instead of CKSEG0ADDR()
MIPS: KVM: Use virt_to_phys() to get commpage PFN
MIPS: Fix definition of KSEGX() for 64-bit
KVM: VMX: Add VMCS to CPU's loaded VMCSs before VMPTRLD
kvm: x86: nVMX: maintain internal copy of current VMCS
KVM: PPC: Book3S HV: Save/restore TM state in H_CEDE
KVM: PPC: Book3S HV: Pull out TM state save/restore into separate procedures
KVM: arm64: vgic-its: Simplify MAPI error handling
KVM: arm64: vgic-its: Make vgic_its_cmd_handle_mapi similar to other handlers
KVM: arm64: vgic-its: Turn device_id validation into generic ID validation
...
debugfs_create_file returns NULL on error so an IS_ERR test is
incorrect here and a NULL check is required.
The Coccinelle semantic patch used to make this change is as follows:
@@
expression e;
@@
e = debugfs_create_file(...);
if(
- IS_ERR(e)
+ !e
)
{
<+...
return
- PTR_ERR(e)
+ -ENOMEM
;
...+>
}
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Cc: julia.lawall@lip6.fr
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13834/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The MIPS Coherence Manager (CM) can propagate address-based ("hit")
cache operations to other cores in the coherent system, alleviating
software of the need to use SMP calls, however indexed cache operations
are not propagated by hardware since doing so makes no sense for
separate caches.
Update r4k_op_needs_ipi() to report that only hit cache operations are
globalized by the CM, requiring indexed cache operations to be
globalized by software via an SMP call.
r4k_on_each_cpu() previously had a special case for CONFIG_MIPS_MT_SMP,
intended to avoid the SMP calls when the only other CPUs in the system
were other VPEs in the same core, and hence sharing the same caches.
This was changed by commit cccf34e941 ("MIPS: c-r4k: Fix cache
flushing for MT cores") to apparently handle multi-core multi-VPE
systems, but it focussed mainly on hit cache ops, so the SMP calls were
still disabled entirely for CM systems.
This doesn't normally cause problems, but tests can be written to hit
these corner cases by using multiple threads, or changing task
affinities to force the process to migrate cores. For example the
failure of mprotect RW->RX to globally sync icaches (via
flush_cache_range) can be detected by modifying and mprotecting a code
page on one core, and migrating to a different core to execute from it.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Leonid Yegoshin <leonid.yegoshin@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13807/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Avoid SMP calls for flushing small icache ranges. On non-CM platforms,
and CM platforms too after we make r4k_on_each_cpu() take the cache op
type into account, it will be called on multiple CPUs due to the
possibility that local_r4k_flush_icache_range_ipi() could do
non-globalized indexed cache ops. This rougly copies the range size
check out into r4k_flush_icache_range(), which can disallow indexed
cache ops and allow r4k_on_each_cpu() to skip the SMP call.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Leonid Yegoshin <leonid.yegoshin@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13805/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Allow the permitted cache op types used by
local_r4k_flush_icache_range_ipi() to be overridden by the SMP caller.
This will allow SMP calls to be avoided under certain circumstances,
falling back to a single CPU performing globalized hit cache ops only.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Leonid Yegoshin <leonid.yegoshin@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13803/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Split the operation of r4k_flush_kernel_vmap_range() into separate
SMP callbacks for the indexed cache flush and hit cache flush cases,
since the logic to determine which to use can be determined by the
initiating CPU prior to doing any SMP calls.
This will help when we change r4k_on_each_cpu() to distinguish indexed
and hit cache ops in a later patch, preventing globalized hit cache ops
being performed redundantly on multiple CPUs.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Leonid Yegoshin <leonid.yegoshin@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13806/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When performing SMP calls to foreign cores, exclude sibling CPUs from
the provided map, as we already handle the local core on the current
CPU. This prevents an SMP call from for example core 0, VPE 1 to VPE 0
on the same core.
In the process the cpu_foreign_map cpumask is turned into an array of
cpumasks, so that each CPU has its own version of it which excludes
sibling CPUs. r4k_op_needs_ipi() is also updated to reflect that cache
management SMP calls are not needed when all CPUs are siblings (i.e.
there are no foreign CPUs according to the new cpu_foreign_map[]
semantics which exclude siblings).
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Leonid Yegoshin <leonid.yegoshin@imgtec.com>
Cc: Felix Fietkau <nbd@nbd.name>
Cc: Jayachandran C. <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13801/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Several cache operations are optimised to return early from the SMP call
handler if the memory map in question has no valid ASID on the current
CPU, or any online CPU in the case of MIPS_MT_SMP. The idea is that if a
memory map has never been used on a CPU it shouldn't have cache lines in
need of flushing.
However this doesn't cover all cases when ASIDs for other CPUs need to
be checked:
- Offline VPEs may have recently been online and brought lines into the
(shared) cache, so they should also be checked, rather than only
online CPUs.
- SMP systems with a Coherence Manager (CM), but with MT disabled still
have globalized hit cache ops, but don't use SMP calls, so all present
CPUs should be taken into account.
- R6 systems have a different multithreading implementation, so
MIPS_MT_SMP won't be set, but as above may still have a CM which
globalizes hit cache ops.
Additionally for non-globalized cache operations where an SMP call to a
single VPE in each foreign core is used, it is not necessary to check
every CPU in the system, only sibling CPUs sharing the same first level
cache.
Fix this by making has_valid_asid() take a cache op type argument like
r4k_on_each_cpu(), so it can determine whether r4k_on_each_cpu() will
have done SMP calls to other cores. It can then determine which set of
CPUs to check the ASIDs of based on that, excluding foreign CPUs if an
SMP call will have been performed.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Leonid Yegoshin <leonid.yegoshin@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13804/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The r4k_on_each_cpu() function calls the specified cache flush helper on
other CPUs if deemed necessary due to the cache ops not being
globalized by hardware. However this really depends on the cache op
addressing type, as the MIPS Coherence Manager (CM) if present will
globalize "hit" cache ops (addressed by virtual address), but not
"index" cache ops (addressed by cache index). This results in index
cache ops only being performed on a single CPU when CM is present.
Most (but not all) of the functions called by r4k_on_each_cpu() perform
cache operations exclusively with a single cache op type, so add a type
argument and modify the callers to pass in some combination of R4K_HIT
(global kernel virtual addressing or user virtual addressing
conditional upon matching active_mm) and R4K_INDEX (index into cache).
This will allow r4k_on_each_cpu() to later distinguish these cases and
decide whether to perform an SMP call based on it.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Leonid Yegoshin <leonid.yegoshin@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13798/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Avoid the dcache and scache flush in local_r4k_flush_cache_sigtramp() if
the icache fills straight from the dcache.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13802/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fix r4k_flush_cache_sigtramp() and local_r4k_flush_cache_sigtramp() to
flush the delay slot emulation trampoline cacheline through a kmap
rather than directly when the active_mm doesn't match that of the task
initiating the flush, a bit like local_r4k_flush_cache_page() does.
This would fix a corner case on SMP systems without hardware globalized
hit cache ops, where a migration to another CPU after the flush, where
that CPU did not have the same mm active at the time of the flush, could
result in stale icache content being executed instead of the trampoline,
e.g. from a previous delay slot emulation with a similar stack pointer.
This case was artificially triggered by replacing the icache flush with
a full indexed flush (not globalized on CM systems) and forcing the SMP
call to take place, with a test program that alternated two FPU delay
slots with a parent process repeatedly changing scheduler affinity.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13797/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The SMP flush_tlb_*() functions may clear the memory map's ASIDs for
other CPUs if the mm has only a single user (the current CPU) in order
to avoid SMP calls. However this makes it appear to has_valid_asid(),
which is used by various cache flush functions, as if the CPUs have
never run in the mm, and therefore can't have cached any of its memory.
For flush_tlb_mm() this doesn't sound unreasonable.
flush_tlb_range() corresponds to flush_cache_range() which does do full
indexed cache flushes, but only on the icache if the specified mapping
is executable, otherwise it doesn't guarantee that there are no cache
contents left for the mm.
flush_tlb_page() corresponds to flush_cache_page(), which will perform
address based cache ops on the specified page only, and also only
touches the icache if the page is executable. It does not guarantee that
there are no cache contents left for the mm.
For example, this affects flush_cache_range() which uses the
has_valid_asid() optimisation. It is required to flush the icache when
mappings are made executable (e.g. using mprotect) so they are
immediately usable. If some code is changed to non executable in order
to be modified then it will not be flushed from the icache during that
time, but the ASID on other CPUs may still be cleared for TLB flushing.
When the code is changed back to executable, flush_cache_range() will
assume the code hasn't run on those other CPUs due to the zero ASID, and
won't invalidate the icache on them.
This is fixed by clearing the other CPUs ASIDs to 1 instead of 0 for the
above two flush_tlb_*() functions when the corresponding cache flushes
are likely to be incomplete (non executable range flush, or any page
flush). This ASID appears valid to has_valid_asid(), but still triggers
ASID regeneration due to the upper ASID version bits being 0, which is
less than the minimum ASID version of 1 and so always treated as stale.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Leonid Yegoshin <leonid.yegoshin@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13795/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The expression "uasm_in_compat_space_p(swpd) && !uasm_rel_lo(swpd)" is
used twice in build_get_pgd_vmalloc64(), one of which is assigned to the
local variable single_insn_swpd. Update the other use to just use
single_insn_swpd instead to remove the duplication.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: David Daney <ddaney@caviumnetworks.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13779/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
uasm_in_compat_space_p() determines whether the given value is in the
32-bit compatibility part of the 64-bit address space, i.e. is in 32-bit
sign-extended form, however it only handles the top half of the value
space (corresponding to the kernel compatibility segments in the upper
half of the address space). Since values < 2^31 (corresponding to the
low 2GiB of the address space) can also be handled using 32-bit
instructions (e.g. a LUI and ADDIU) rather than convoluted 64-bit
immediate generation, rewrite it with a cast to check whether the
address matches its 32-bit sign extended form.
This allows UASM_i_LA to be used to generate arbitrary 32-bit immediates
more efficiently on 64-bit CPUs, i.e. more like the li (load immediate)
pseudo-instruction.
For example this code to load the immediate (ST0_EXL | KSU_USER |
ST0_BEV | ST0_KX) into k0 with UASM_i_LA():
lui k0,0x0
dsll k0,k0,0x10
daddiu k0,k0,64
dsll k0,k0,0x10
daddiu k0,k0,146
Changes to this more efficient version:
lui k0,0x40
addiu k0,k0,146
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13778/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Very early versions of the 1004K had an hardware issue that made index
cache ops unsafe so they had to be avoided and hit ops be used instead.
This may significantly slow down cache maintenance operations. Only
very early FPGA versions of the 1004K were affected so let's get rid
of the workaround which was only implemented for the DMA cache
maintenance operations anyway.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add the R6 MUL instruction encoding for 3 operand signed multiply to
uasm so that KVM can use uasm for generating its entry point code at
runtime on R6.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add MTHI/MTLO instructions for writing to the hi & lo registers to uasm
so that KVM can use uasm for generating its entry point code at runtime.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add DI instruction for disabling interrupts to uasm so that KVM can use
uasm for generating its entry point code at runtime.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add CFCMSA/CTCMSA instructions for accessing MSA control registers to
uasm so that KVM can use uasm for generating its entry point code at
runtime.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add CFC1/CTC1 instructions for accessing FP control registers to uasm so
that KVM can use uasm for generating its entry point code at runtime.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The Config.VI bit specifies that the instruction cache is virtually
tagged, which is checked in c-r4k.c's probe_pcache(). Add a proper
definition for it in mipsregs.h and make use of it.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The Hardware page Table Walker (HTW) is being misconfigured on 64-bit
kernels. The PWSize.PS (pointer size) bit determines whether pointers
within directories are loaded as 32-bit or 64-bit addresses, but was
never being set to 1 for 64-bit kernels where the unsigned long in pgd_t
is 64-bits wide.
This actually reduces rather than improves performance when the HTW is
enabled on P6600 since the HTW is initiated lots, but walks are all
aborted due I think to bad intermediate pointers.
Since we were already taking the width of the PTEs into account by
setting PWSize.PTEW, which is the left shift applied to the page table
index *in addition to* the native pointer size, we also need to reduce
PTEW by 1 when PS=1. This is done by calculating PTEW based on the
relative size of pte_t compared to pgd_t.
Finally in order for the HTW to be used when PS=1, the appropriate
XK/XS/XU bits corresponding to the different 64-bit segments need to be
set in PWCtl. We enable only XU for now to enable walking for XUSeg.
Supporting walking for XKSeg would be a bit more involved so is left for
a future patch. It would either require the use of a per-CPU top level
base directory if supported by the HTW (a bit like pgd_current but with
a second entry pointing at swapper_pg_dir), or the HTW would prepend bit
63 of the address to the global directory index which doesn't really
match how we split user and kernel page directories.
Fixes: cab25bc753 ("MIPS: Extend hardware table walking support to MIPS64")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13364/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add field definitions for some of the 64-bit specific Hardware page
Table Walker (HTW) register fields in PWSize and PWCtl, in preparation
for fixing the 64-bit HTW configuration.
Also print these fields out along with the others in print_htw_config().
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13363/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Merge updates from Andrew Morton:
- fsnotify fix
- poll() timeout fix
- a few scripts/ tweaks
- debugobjects updates
- the (small) ocfs2 queue
- Minor fixes to kernel/padata.c
- Maybe half of the MM queue
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (117 commits)
mm, page_alloc: restore the original nodemask if the fast path allocation failed
mm, page_alloc: uninline the bad page part of check_new_page()
mm, page_alloc: don't duplicate code in free_pcp_prepare
mm, page_alloc: defer debugging checks of pages allocated from the PCP
mm, page_alloc: defer debugging checks of freed pages until a PCP drain
cpuset: use static key better and convert to new API
mm, page_alloc: inline pageblock lookup in page free fast paths
mm, page_alloc: remove unnecessary variable from free_pcppages_bulk
mm, page_alloc: pull out side effects from free_pages_check
mm, page_alloc: un-inline the bad part of free_pages_check
mm, page_alloc: check multiple page fields with a single branch
mm, page_alloc: remove field from alloc_context
mm, page_alloc: avoid looking up the first zone in a zonelist twice
mm, page_alloc: shortcut watermark checks for order-0 pages
mm, page_alloc: reduce cost of fair zone allocation policy retry
mm, page_alloc: shorten the page allocator fast path
mm, page_alloc: check once if a zone has isolated pageblocks
mm, page_alloc: move __GFP_HARDWALL modifications out of the fastpath
mm, page_alloc: simplify last cpupid reset
mm, page_alloc: remove unnecessary initialisation from __alloc_pages_nodemask()
...
I've just discovered that the useful-sounding has_transparent_hugepage()
is actually an architecture-dependent minefield: on some arches it only
builds if CONFIG_TRANSPARENT_HUGEPAGE=y, on others it's also there when
not, but on some of those (arm and arm64) it then gives the wrong
answer; and on mips alone it's marked __init, which would crash if
called later (but so far it has not been called later).
Straighten this out: make it available to all configs, with a sensible
default in asm-generic/pgtable.h, removing its definitions from those
arches (arc, arm, arm64, sparc, tile) which are served by the default,
adding #define has_transparent_hugepage has_transparent_hugepage to
those (mips, powerpc, s390, x86) which need to override the default at
runtime, and removing the __init from mips (but maybe that kind of code
should be avoided after init: set a static variable the first time it's
called).
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Andres Lagar-Cavilla <andreslc@google.com>
Cc: Yang Shi <yang.shi@linaro.org>
Cc: Ning Qu <quning@gmail.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Konstantin Khlebnikov <koct9i@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Vineet Gupta <vgupta@synopsys.com> [arch/arc]
Acked-by: Gerald Schaefer <gerald.schaefer@de.ibm.com> [arch/s390]
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
XPA kernels hardcode for the presence of RIXI - the PTE format & its
handling presume RI & XI bits. Make this dependence explicit by panicing
if we run on a system that violates it.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13125/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Performing an MTHC0 instruction without XPA being present will trigger a
reserved instruction exception, therefore conditionalise the use of this
instruction when building TLB handlers (build_update_entries()), and in
__update_tlb().
This allows an XPA kernel to run on non XPA hardware without that
instruction implemented, just like it can run on XPA capable hardware
without XPA in use (with the noxpa kernel argument) or with XPA not
configured in hardware.
[paul.burton@imgtec.com:
- Rebase atop other TLB work.
- Add "mm" to subject.
- Handle the __kmap_pgprot case.]
Fixes: c5b367835c ("MIPS: Add support for XPA.")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: David Hildenbrand <dahi@linux.vnet.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jerome Marchand <jmarchan@redhat.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13124/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We can simplify build_update_entries by unifying the code for the 36 bit
physical addressing with MIPS32 case with the general case, by using
pte_off_ variables in all cases & handling the trivial
_PAGE_GLOBAL_SHIFT == 0 case in build_convert_pte_to_entrylo. This
leaves XPA as the only special case.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13123/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The XPA case in iPTE_SW or's in software mode bits to the pte_low value
(which is what actually ends up in the high 32 bits of EntryLo...). It
does this presuming that only bits in the upper 16 bits of the 32 bit
pte_low value will be set. Make this assumption explicit with a BUG_ON.
A similar assumption is made for the hardware mode bits, which are or'd
in with a single ori instruction. Make that assumption explicit with a
BUG_ON too.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13122/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Rather than hardcode a scratch register for the XPA case in iPTE_SW,
pass one through from the work registers allocated by the caller. This
allows for the XPA path to function correctly regardless of the work
registers in use.
Without doing this there are cases (where KScratch registers are
unavailable) in which iPTE_SW will incorrectly clobber $1 despite it
already being in use for the PTE or PTE pointer.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13121/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
For XPA kernels build_update_entries() uses $1 (at) as a scratch
register, but doesn't arrange for it to be preserved, so it will always
be clobbered by the TLB refill exception. Although this register
normally has a very short lifetime that doesn't cross memory accesses,
TLB refills due to instruction fetches (either on a page boundary or
after preemption) could clobber live data, and its easy to reproduce
the clobber with a little bit of assembler code.
Note that the use of a hardware page table walker will partly mask the
problem, as the TLB refill handler will not always be invoked.
This is fixed by avoiding the use of the extra scratch register. The
pte_high parts (going into the lower half of the EntryLo registers) are
loaded and manipulated separately so as to keep the PTE pointer around
for the other halves (instead of storing in the scratch register), and
the pte_low parts (going into the high half of the EntryLo registers)
are masked with 0x00ffffff using an ext instruction (instead of loading
0x00ffffff into the scratch register and AND'ing).
[paul.burton@imgtec.com:
- Rebase atop other TLB work.
- Use ext instead of an sll, srl sequence.
- Use cpu_has_xpa instead of #ifdefs.
- Modify commit subject to include "mm".]
Fixes: c5b367835c ("MIPS: Add support for XPA.")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13120/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
There are 2 distinct cases in which a kernel for a MIPS32 CPU
(CONFIG_CPU_MIPS32=y) may use 64 bit physical addresses
(CONFIG_PHYS_ADDR_T_64BIT=y):
- 36 bit physical addressing as used by RMI Alchemy & Netlogic XLP/XLR
CPUs.
- MIPS32r5 eXtended Physical Addressing (XPA).
These 2 cases are distinct in that they require different behaviour from
the kernel - the EntryLo registers have different formats. Until Linux
v4.1 we only supported the first case, with code conditional upon the 2
aforementioned Kconfig variables being set. Commit c5b367835c ("MIPS:
Add support for XPA.") added support for the second case, but did so by
modifying the code that existed for the first case rather than treating
the 2 cases as distinct. Since the EntryLo registers have different
formats this breaks the 36 bit Alchemy/XLP/XLR case. Fix this by
splitting the 2 cases, with XPA cases now being conditional upon
CONFIG_XPA and the non-XPA case matching the code as it existed prior to
commit c5b367835c ("MIPS: Add support for XPA.").
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reported-by: Manuel Lauss <manuel.lauss@gmail.com>
Tested-by: Manuel Lauss <manuel.lauss@gmail.com>
Fixes: c5b367835c ("MIPS: Add support for XPA.")
Cc: James Hogan <james.hogan@imgtec.com>
Cc: David Daney <david.daney@cavium.com>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Cc: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: David Hildenbrand <dahi@linux.vnet.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Alex Smith <alex.smith@imgtec.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: stable@vger.kernel.org # v4.1+
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13119/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Ever since support for RI/XI was implemented by commit 6dd9344cfc
("MIPS: Implement Read Inhibit/eXecute Inhibit") we've had a mixture of
_PAGE_READ & _PAGE_NO_READ bits. Rather than keep both around, switch
away from using _PAGE_READ to determine page presence & instead invert
the use to _PAGE_NO_READ. Wherever we formerly had no definition for
_PAGE_NO_READ, change what was _PAGE_READ to _PAGE_NO_READ. The end
result is that we consistently use _PAGE_NO_READ to determine whether a
page is readable, regardless of whether RI/XI is implemented.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Cc: David Daney <david.daney@cavium.com>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Alex Smith <alex.smith@imgtec.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13116/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The hardware page table walker (HTW) configuration is broken on XPA
kernels where XPA couldn't be enabled (either nohtw or the hardware
doesn't support it). This is because the PWSize.PTEW field (PTE width)
was only set to 8 bytes (an extra shift of 1) in config_htw_params() if
PageGrain.ELPA (enable large physical addressing) is set. On an XPA
kernel though the size of PTEs is fixed at 8 bytes regardless of whether
XPA could actually be enabled.
Fix the initialisation of this field based on sizeof(pte_t) instead.
Fixes: c5b367835c ("MIPS: Add support for XPA.")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Steven J. Hill <sjhill@realitydiluted.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13113/
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
In preparation for supporting variable ASID masks, retrieve ASID masks
using functions in asm/cpu-info.h which accept struct cpuinfo_mips. This
will allow those functions to determine the ASID mask based upon the CPU
in a later patch. This also allows for the r3k & r8k cases to be handled
in Kconfig, which is arguably cleaner than the previous #ifdefs.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13210/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
New Loongson 3 CPU (since Loongson-3A R2, as opposed to Loongson-3A R1,
Loongson-3B R1 and Loongson-3B R2) has many enhancements, such as FTLB,
L1-VCache, EI/DI/Wait/Prefetch instruction, DSP/DSPv2 ASE, User Local
register, Read-Inhibit/Execute-Inhibit, SFB (Store Fill Buffer), Fast
TLB refill support, etc.
This patch introduce a config option, CONFIG_LOONGSON3_ENHANCEMENT, to
enable those enhancements which are not probed at run time. If you want
a generic kernel to run on all Loongson 3 machines, please say 'N'
here. If you want a high-performance kernel to run on new Loongson 3
machines only, please say 'Y' here.
Some additional explanations:
1) SFB locates between core and L1 cache, it causes memory access out
of order, so writel/outl (and other similar functions) need a I/O
reorder barrier.
2) Loongson 3 has a bug that di instruction can not save the irqflag,
so arch_local_irq_save() is modified. Since CPU_MIPSR2 is selected
by CONFIG_LOONGSON3_ENHANCEMENT, generic kernel doesn't use ei/di
at all.
3) CPU_HAS_PREFETCH is selected by CONFIG_LOONGSON3_ENHANCEMENT, so
MIPS_CPU_PREFETCH (used by uasm) probing is also put in this patch.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: Steven J . Hill <sjhill@realitydiluted.com>
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12755/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Loongson-3A R2 has pwbase/pwfield/pwsize/pwctl registers in CP0 (this
is very similar to HTW) and lwdir/lwpte/lddir/ldpte instructions which
can be used for fast TLB refill.
[ralf@linux-mips.org: Resolve conflict.]
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: Steven J . Hill <sjhill@realitydiluted.com>
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12754/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Loongson-2 has a 4 entry itlb which is a subset of jtlb, Loongson-3 has
a 4 entry itlb and a 4 entry dtlb which are subsets of jtlb. We should
write diag register to invalidate itlb/dtlb when flushing jtlb because
itlb/dtlb are not totally transparent to software.
For Loongson-3A R2 (and newer), we should invalidate ITLB, DTLB, VTLB
and FTLB before we enable/disable FTLB.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: Steven J . Hill <sjhill@realitydiluted.com>
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12753/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Loongson-3 maintains cache coherency by hardware, this means:
1) It's icache is coherent with dcache.
2) It's dcaches don't alias (maybe depend on PAGE_SIZE).
3) It maintains cache coherency across cores (and for DMA).
So we can skip most cache flush operations by setting relevant handlers
to `cache_noop' in `r4k_cache_init'.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: Steven J . Hill <sjhill@realitydiluted.com>
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12752/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
local_r4k___flush_cache_all() is missing a special check for BMIPS5000
processors, we need to blast the S-cache, just like other MTI processors
since we have an inclusive cache. We also need an additional __sync() to
make sure this is completed.
Fixes: d74b0172e4 ("MIPS: BMIPS: Add special cache handling in c-r4k.c")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13012/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
BMIPS5000 and BMIPS5200 processor have no D cache aliases, and this is
properly handled by the per-CPU override added at the end of
r4k_cache_init(), the problem is that the output of probe_pcache()
disagrees with that, since this is too late:
Primary instruction cache 32kB, VIPT, 4-way, linesize 64 bytes.
Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
With the change moved earlier, we now have a consistent output with the
settings we are intending to have:
Primary instruction cache 32kB, VIPT, 4-way, linesize 64 bytes.
Primary data cache 32kB, 4-way, VIPT, no aliases, linesize 32 bytes
Fixes: d74b0172e4 ("MIPS: BMIPS: Add special cache handling in c-r4k.c")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13011/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
BMIPS5000 and BMIPS52000 processors have their I-cache filling from the
D-cache. Since BMIPS_GENERIC does not provide (yet) a
cpu-feature-overrides.h file, this was not set anywhere, so make sure
the R4K cache detection takes care of that.
Fixes: d74b0172e4 ("MIPS: BMIPS: Add special cache handling in c-r4k.c")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13010/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
It's possible for pages to become visible prior to update_mmu_cache
running if a thread within the same address space preempts the current
thread or runs simultaneously on another CPU. That is, the following
scenario is possible:
CPU0 CPU1
write to page
flush_dcache_page
flush_icache_page
set_pte_at
map page
update_mmu_cache
If CPU1 maps the page in between CPU0's set_pte_at, which marks it valid
& visible, and update_mmu_cache where the dcache flush occurs then CPU1s
icache will fill from stale data (unless it fills from the dcache, in
which case all is good, but most MIPS CPUs don't have this property).
Commit 4d46a67a3e ("MIPS: Fix race condition in lazy cache flushing.")
attempted to fix that by performing the dcache flush in
flush_icache_page such that it occurs before the set_pte_at call makes
the page visible. However it has the problem that not all code that
writes to pages exposed to userland call flush_icache_page. There are
many callers of set_pte_at under mm/ and only 2 of them do call
flush_icache_page. Thus the race window between a page becoming visible
& being coherent between the icache & dcache remains open in some cases.
To illustrate some of the cases, a WARN was added to __update_cache with
this patch applied that triggered in cases where a page about to be
flushed from the dcache was not the last page provided to
flush_icache_page. That is, backtraces were obtained for cases in which
the race window is left open without this patch. The 2 standout examples
follow.
When forking a process:
[ 15.271842] [<80417630>] __update_cache+0xcc/0x188
[ 15.277274] [<80530394>] copy_page_range+0x56c/0x6ac
[ 15.282861] [<8042936c>] copy_process.part.54+0xd40/0x17ac
[ 15.289028] [<80429f80>] do_fork+0xe4/0x420
[ 15.293747] [<80413808>] handle_sys+0x128/0x14c
When exec'ing an ELF binary:
[ 14.445964] [<80417630>] __update_cache+0xcc/0x188
[ 14.451369] [<80538d88>] move_page_tables+0x414/0x498
[ 14.457075] [<8055d848>] setup_arg_pages+0x220/0x318
[ 14.462685] [<805b0f38>] load_elf_binary+0x530/0x12a0
[ 14.468374] [<8055ec3c>] search_binary_handler+0xbc/0x214
[ 14.474444] [<8055f6c0>] do_execveat_common+0x43c/0x67c
[ 14.480324] [<8055f938>] do_execve+0x38/0x44
[ 14.485137] [<80413808>] handle_sys+0x128/0x14c
These code paths write into a page, call flush_dcache_page then call
set_pte_at without flush_icache_page inbetween. The end result is that
the icache can become corrupted & userland processes may execute
unexpected or invalid code, typically resulting in a reserved
instruction exception, a trap or a segfault.
Fix this race condition fully by performing any cache maintenance
required to keep the icache & dcache in sync in set_pte_at, before the
page is made valid. This has the added bonus of ensuring the cache
maintenance always happens in one location, rather than being duplicated
in flush_icache_page & update_mmu_cache. It also matches the way other
architectures solve the same problem (see arm, ia64 & powerpc).
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reported-by: Ionela Voinescu <ionela.voinescu@imgtec.com>
Cc: Lars Persson <lars.persson@axis.com>
Fixes: 4d46a67a3e ("MIPS: Fix race condition in lazy cache flushing.")
Cc: Steven J. Hill <sjhill@realitydiluted.com>
Cc: David Daney <david.daney@cavium.com>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jerome Marchand <jmarchan@redhat.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: stable <stable@vger.kernel.org> # v4.1+
Patchwork: https://patchwork.linux-mips.org/patch/12722/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The following patch will expose __update_cache to highmem pages. Handle
them by mapping them in for the duration of the cache maintenance, just
like in __flush_dcache_page. The code for that isn't shared because we
need the page address in __update_cache so sharing became messy. Given
that the entirity is an extra 5 lines, just duplicate it.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Lars Persson <lars.persson@axis.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jerome Marchand <jmarchan@redhat.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: stable <stable@vger.kernel.org> # v4.1+
Patchwork: https://patchwork.linux-mips.org/patch/12721/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When flush_dcache_page is called on an executable page, that page is
about to be provided to userland & we can presume that the icache
contains no valid entries for its address range. However if the icache
does not fill from the dcache then we cannot presume that the pages
content has been written back as far as the memories that the dcache
will fill from (ie. L2 or further out).
This was being done for lowmem pages, but not for highmem which can lead
to icache corruption. Fix this by mapping highmem pages & flushing their
content from the dcache in __flush_dcache_page before providing the page
to userland, just as is done for lowmem pages.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Lars Persson <lars.persson@axis.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12720/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add casses supporting the M6250 CPU to various switch statements in the
core MIPS kernel code that define behaviour dependent upon the CPU.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Joshua Kinard <kumba@gentoo.org>
Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Maciej W. Rozycki <macro@codesourcery.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12374/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add cases supporting the P6600 CPU to various switch statements in
core MIPS kernel code that define behaviour dependent upon the CPU.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Maciej W. Rozycki <macro@imgtec.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Joshua Kinard <kumba@gentoo.org>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Petri Gynther <pgynther@google.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12343/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch ensures that the dev parameter is checked for NULL before it
is dereferenced in massage_gfp_flags. If dev is NULL, then fall back
setting the GFP flag requested and available.
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11919/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Coherence Manager 3 (CM3) as present in I6400 can fill icache lines
effectively from dirty dcaches, so there is no need to flush dirty lines
from dcaches through to L2 prior to icache invalidation.
Set the MIPS_CACHE_IC_F_DC flag such that cpu_has_ic_fills_f_dc
evaluates to true, which avoids those dcache flushes.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Leonid Yegoshin <leonid.yegoshin@imgtec.com>
Cc: Manuel Lauss <manuel.lauss@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12180/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
It is still necessary to handle icache coherency in flush_cache_range()
and copy_to_user_page() when the icache fills from the dcache, even
though the dcache does not need to be written back. However when this
handling was added in commit 2eaa7ec286 ("[MIPS] Handle I-cache
coherency in flush_cache_range()"), it did not do any icache flushing
when it fills from dcache.
Therefore fix r4k_flush_cache_range() to run
local_r4k_flush_cache_range() without taking into account whether icache
fills from dcache, so that the icache coherency gets handled. Checks are
also added in local_r4k_flush_cache_range() so that the dcache blast
doesn't take place when icache fills from dcache.
A test to mmap a page PROT_READ|PROT_WRITE, modify code in it, and
mprotect it to VM_READ|VM_EXEC (similar to case described in above
commit) can hit this case quite easily to verify the fix.
A similar check was added in commit f8829caee3 ("[MIPS] Fix aliasing
bug in copy_to_user_page / copy_from_user_page"), so also fix
copy_to_user_page() similarly, to call flush_cache_page() without taking
into account whether icache fills from dcache, since flush_cache_page()
already takes that into account to avoid performing a dcache flush.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Leonid Yegoshin <leonid.yegoshin@imgtec.com>
Cc: Manuel Lauss <manuel.lauss@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12179/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
After writing the appropriate mask to the cop0 PageMask register, read
the register back & check it matches what we want. If it doesn't then
the MMU does not support the page size the kernel is configured for and
we're better off bailing than continuing to do odd things with TLB
exceptions.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Joshua Kinard <kumba@gentoo.org>
Cc: Rafał Miłecki <zajec5@gmail.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/10691/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Pull x86 protection key support from Ingo Molnar:
"This tree adds support for a new memory protection hardware feature
that is available in upcoming Intel CPUs: 'protection keys' (pkeys).
There's a background article at LWN.net:
https://lwn.net/Articles/643797/
The gist is that protection keys allow the encoding of
user-controllable permission masks in the pte. So instead of having a
fixed protection mask in the pte (which needs a system call to change
and works on a per page basis), the user can map a (handful of)
protection mask variants and can change the masks runtime relatively
cheaply, without having to change every single page in the affected
virtual memory range.
This allows the dynamic switching of the protection bits of large
amounts of virtual memory, via user-space instructions. It also
allows more precise control of MMU permission bits: for example the
executable bit is separate from the read bit (see more about that
below).
This tree adds the MM infrastructure and low level x86 glue needed for
that, plus it adds a high level API to make use of protection keys -
if a user-space application calls:
mmap(..., PROT_EXEC);
or
mprotect(ptr, sz, PROT_EXEC);
(note PROT_EXEC-only, without PROT_READ/WRITE), the kernel will notice
this special case, and will set a special protection key on this
memory range. It also sets the appropriate bits in the Protection
Keys User Rights (PKRU) register so that the memory becomes unreadable
and unwritable.
So using protection keys the kernel is able to implement 'true'
PROT_EXEC on x86 CPUs: without protection keys PROT_EXEC implies
PROT_READ as well. Unreadable executable mappings have security
advantages: they cannot be read via information leaks to figure out
ASLR details, nor can they be scanned for ROP gadgets - and they
cannot be used by exploits for data purposes either.
We know about no user-space code that relies on pure PROT_EXEC
mappings today, but binary loaders could start making use of this new
feature to map binaries and libraries in a more secure fashion.
There is other pending pkeys work that offers more high level system
call APIs to manage protection keys - but those are not part of this
pull request.
Right now there's a Kconfig that controls this feature
(CONFIG_X86_INTEL_MEMORY_PROTECTION_KEYS) that is default enabled
(like most x86 CPU feature enablement code that has no runtime
overhead), but it's not user-configurable at the moment. If there's
any serious problem with this then we can make it configurable and/or
flip the default"
* 'mm-pkeys-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (38 commits)
x86/mm/pkeys: Fix mismerge of protection keys CPUID bits
mm/pkeys: Fix siginfo ABI breakage caused by new u64 field
x86/mm/pkeys: Fix access_error() denial of writes to write-only VMA
mm/core, x86/mm/pkeys: Add execute-only protection keys support
x86/mm/pkeys: Create an x86 arch_calc_vm_prot_bits() for VMA flags
x86/mm/pkeys: Allow kernel to modify user pkey rights register
x86/fpu: Allow setting of XSAVE state
x86/mm: Factor out LDT init from context init
mm/core, x86/mm/pkeys: Add arch_validate_pkey()
mm/core, arch, powerpc: Pass a protection key in to calc_vm_flag_bits()
x86/mm/pkeys: Actually enable Memory Protection Keys in the CPU
x86/mm/pkeys: Add Kconfig prompt to existing config option
x86/mm/pkeys: Dump pkey from VMA in /proc/pid/smaps
x86/mm/pkeys: Dump PKRU with other kernel registers
mm/core, x86/mm/pkeys: Differentiate instruction fetches
x86/mm/pkeys: Optimize fault handling in access_error()
mm/core: Do not enforce PKEY permissions on remote mm access
um, pkeys: Add UML arch_*_access_permitted() methods
mm/gup, x86/mm/pkeys: Check VMAs and PTEs for protection keys
x86/mm/gup: Simplify get_user_pages() PTE bit handling
...
The success of CMA allocation largely depends on the success of
migration and key factor of it is page reference count. Until now, page
reference is manipulated by direct calling atomic functions so we cannot
follow up who and where manipulate it. Then, it is hard to find actual
reason of CMA allocation failure. CMA allocation should be guaranteed
to succeed so finding offending place is really important.
In this patch, call sites where page reference is manipulated are
converted to introduced wrapper function. This is preparation step to
add tracepoint to each page reference manipulation function. With this
facility, we can easily find reason of CMA allocation failure. There is
no functional change in this patch.
In addition, this patch also converts reference read sites. It will
help a second step that renames page._count to something else and
prevents later attempt to direct access to it (Suggested by Andrew).
Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Sergey Senozhatsky <sergey.senozhatsky.work@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In current scache init cache line_size is determined from
cpu config register, however if there there no scache
then mips_sc_probe_cm3 function populates a invalid line_size of 2.
The invalid line_size can cause a NULL pointer deference
during r4k_dma_cache_inv as r4k_blast_scache is populated
based on line_size. Scache line_size of 2 is invalid option in
r4k_blast_scache_setup.
This issue was faced during a MIPS I6400 based virtual platform bring up
where scache was not available in virtual platform model.
Signed-off-by: Govindraj Raja <Govindraj.Raja@imgtec.com>
Fixes: 7d53e9c4cd21("MIPS: CM3: Add support for CM3 L2 cache.")
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hartley <James.Hartley@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: stable@vger.kernel.org # v4.2+
Patchwork: https://patchwork.linux-mips.org/patch/12710/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Replace calls to get_random_int() followed by a cast to (unsigned long)
with calls to get_random_long(). Also address shifting bug which, in
case of x86 removed entropy mask for mmap_rnd_bits values > 31 bits.
Signed-off-by: Daniel Cashman <dcashman@android.com>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: "Theodore Ts'o" <tytso@mit.edu>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: David S. Miller <davem@davemloft.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Nick Kralevich <nnk@google.com>
Cc: Jeff Vander Stoep <jeffv@google.com>
Cc: Mark Salyzyn <salyzyn@android.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We will soon modify the vanilla get_user_pages() so it can no
longer be used on mm/tasks other than 'current/current->mm',
which is by far the most common way it is called. For now,
we allow the old-style calls, but warn when they are used.
(implemented in previous patch)
This patch switches all callers of:
get_user_pages()
get_user_pages_unlocked()
get_user_pages_locked()
to stop passing tsk/mm so they will no longer see the warnings.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Dave Hansen <dave@sr71.net>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: jack@suse.cz
Cc: linux-mm@kvack.org
Link: http://lkml.kernel.org/r/20160212210156.113E9407@viggo.jf.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Commit c014d164f2 ("MIPS: Add platform callback before initializing
the L2 cache") added a platform_early_l2_init function in order to allow
platforms to probe for the CM before L2 initialisation is performed, so
that CM GCRs are available to mips_sc_probe.
That commit actually fails to do anything useful, since it checks
mips_cm_revision to determine whether it should call mips_cm_probe but
the result of mips_cm_revision will always be 0 until mips_cm_probe has
been called. Thus the "early" mips_cm_probe call never occurs.
Fix this & drop the useless weak platform_early_l2_init function by
simply calling mips_cm_probe from setup_arch. For platforms that don't
select CONFIG_MIPS_CM this will be a no-op, and for those that do it
removes the requirement for them to call mips_cm_probe manually
(although doing so isn't harmful for now).
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Aaro Koskinen <aaro.koskinen@nokia.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: Jaedon Shin <jaedon.shin@gmail.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12475/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for MIPS for 4.5 plus some 4.4 fixes.
The executive summary:
- ATH79 platform improvments, use DT bindings for the ATH79 USB PHY.
- Avoid useless rebuilds for zboot.
- jz4780: Add NEMC, BCH and NAND device tree nodes
- Initial support for the MicroChip's DT platform. As all the device
drivers are missing this is still of limited use.
- Some Loongson3 cleanups.
- The unavoidable whitespace polishing.
- Reduce clock skew when synchronizing the CPU cycle counters on CPU
startup.
- Add MIPS R6 fixes.
- Lots of cleanups across arch/mips as fallout from KVM.
- Lots of minor fixes and changes for IEEE 754-2008 support to the
FPU emulator / fp-assist software.
- Minor Ralink, BCM47xx and bcm963xx platform support improvments.
- Support SMP on BCM63168"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (84 commits)
MIPS: zboot: Add support for serial debug using the PROM
MIPS: zboot: Avoid useless rebuilds
MIPS: BMIPS: Enable ARCH_WANT_OPTIONAL_GPIOLIB
MIPS: bcm63xx: nvram: Remove unused bcm63xx_nvram_get_psi_size() function
MIPS: bcm963xx: Update bcm_tag field image_sequence
MIPS: bcm963xx: Move extended flash address to bcm_tag header file
MIPS: bcm963xx: Move Broadcom BCM963xx image tag data structure
MIPS: bcm63xx: nvram: Use nvram structure definition from header file
MIPS: bcm963xx: Add Broadcom BCM963xx board nvram data structure
MAINTAINERS: Add KVM for MIPS entry
MIPS: KVM: Add missing newline to kvm_err()
MIPS: Move KVM specific opcodes into asm/inst.h
MIPS: KVM: Use cacheops.h definitions
MIPS: Break down cacheops.h definitions
MIPS: Use EXCCODE_ constants with set_except_vector()
MIPS: Update trap codes
MIPS: Move Cause.ExcCode trap codes to mipsregs.h
MIPS: KVM: Make kvm_mips_{init,exit}() static
MIPS: KVM: Refactor added offsetof()s
MIPS: KVM: Convert EXPORT_SYMBOL to _GPL
...
Commit be0c37c985 (MIPS: Rearrange PTE bits into fixed positions.)
defines fixed PTE bits for MIPS R2. Then, commit d7b631419b
(MIPS: pgtable-bits: Fix XPA damage to R6 definitions.) adds the MIPS
R6 definitions in the same way as MIPS R2. But some R6 #ifdefs in the
later commit are missing, so in this patch I fix that.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: stable@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12164/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Let's define page_mapped() to be true for compound pages if any
sub-pages of the compound page is mapped (with PMD or PTE).
On other hand page_mapcount() return mapcount for this particular small
page.
This will make cases like page_get_anon_vma() behave correctly once we
allow huge pages to be mapped with PTE.
Most users outside core-mm should use page_mapcount() instead of
page_mapped().
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Tested-by: Sasha Levin <sasha.levin@oracle.com>
Tested-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Acked-by: Jerome Marchand <jmarchan@redhat.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Rik van Riel <riel@redhat.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Steve Capper <steve.capper@linaro.org>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Christoph Lameter <cl@linux.com>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With new refcounting we don't need to mark PMDs splitting. Let's drop
code to handle this.
pmdp_splitting_flush() is not needed too: on splitting PMD we will do
pmdp_clear_flush() + set_pte_at(). pmdp_clear_flush() will do IPI as
needed for fast_gup.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Sasha Levin <sasha.levin@oracle.com>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Cc: Jerome Marchand <jmarchan@redhat.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Rik van Riel <riel@redhat.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Steve Capper <steve.capper@linaro.org>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Christoph Lameter <cl@linux.com>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Tail page refcounting is utterly complicated and painful to support.
It uses ->_mapcount on tail pages to store how many times this page is
pinned. get_page() bumps ->_mapcount on tail page in addition to
->_count on head. This information is required by split_huge_page() to
be able to distribute pins from head of compound page to tails during
the split.
We will need ->_mapcount to account PTE mappings of subpages of the
compound page. We eliminate need in current meaning of ->_mapcount in
tail pages by forbidding split entirely if the page is pinned.
The only user of tail page refcounting is THP which is marked BROKEN for
now.
Let's drop all this mess. It makes get_page() and put_page() much
simpler.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Tested-by: Sasha Levin <sasha.levin@oracle.com>
Tested-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Jerome Marchand <jmarchan@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Rik van Riel <riel@redhat.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Steve Capper <steve.capper@linaro.org>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Christoph Lameter <cl@linux.com>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Recent changes to how GFP_ATOMIC is defined seems to have broken the
condition to use mips_alloc_from_contiguous() in
mips_dma_alloc_coherent().
I couldn't bottom out the exact change but I think it's this commit
d0164adc89 ("mm, page_alloc: distinguish between being unable to
sleep, unwilling to sleep and avoiding waking kswapd").
GFP_ATOMIC has multiple bits set and the check for !(gfp & GFP_ATOMIC)
isn't enough.
The reason behind this condition is to check whether we can potentially
do a sleeping memory allocation. Use gfpflags_allow_blocking() instead
which should be more robust.
Signed-off-by: Qais Yousef <qais.yousef@imgtec.com>
Acked-by: Mel Gorman <mgorman@techsingularity.net>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull MIPS updates from Ralf Baechle:
"These are the highlists of the main MIPS pull request for 4.4:
- Add latencytop support
- Support appended DTBs
- VDSO support and initially use it for gettimeofday.
- Drop the .MIPS.abiflags and ELF NOTE sections from vmlinux
- Support for the 5KE, an internal test core.
- Switch all MIPS platfroms to libata drivers.
- Improved support, cleanups for ralink and Lantiq platforms.
- Support for the new xilfpga platform.
- A number of DTB improvments for BMIPS.
- Improved support for CM and CPS.
- Minor JZ4740 and BCM47xx enhancements"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (120 commits)
MIPS: idle: add case for CPU_5KE
MIPS: Octeon: Support APPENDED_DTB
MIPS: vmlinux: create a section for appended DTB
MIPS: Clean up compat_siginfo_t
MIPS: Fix PAGE_MASK definition
MIPS: BMIPS: Enable GZIP ramdisk and timed printks
MIPS: Add xilfpga defconfig
MIPS: xilfpga: Add mipsfpga platform code
MIPS: xilfpga: Add xilfpga device tree files.
dt-bindings: MIPS: Document xilfpga bindings and boot style
MIPS: Make MIPS_CMDLINE_DTB default
MIPS: Make the kernel arguments from dtb available
MIPS: Use USE_OF as the guard for appended dtb
MIPS: BCM63XX: Use pr_* instead of printk
MIPS: Loongson: Cleanup CONFIG_LOONGSON_SUSPEND.
MIPS: lantiq: Disable xbar fpi burst mode
MIPS: lantiq: Force the crossbar to big endian
MIPS: lantiq: Initialize the USB core on boot
MIPS: lantiq: Return correct value for fpi clock on ar9
MIPS: ralink: Add missing clock on rt305x
...
Extend the existing support for Hardware Table Walking (HTW) to MIPS64
systems by supporting PMDs & setting the pointer size bit in PWSize,
then ceasing to blacklist HTW on MIPS64 systems.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Joshua Kinard <kumba@gentoo.org>
Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: linux-kernel@vger.kernel.org
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/11224/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit 748e787eb6 ("MIPS: Optimize TLB refill for RI/XI
configurations.") stopped explicitly clearing the bits used by software
in PTEs by making use of a rotate instruction that rotates them into the
fill bits of the Entry{Lo,Hi} register. This can only work if there are
actually enough fill bits in the register to cover the software
maintained bits, otherwise we end up writing those bits into the upper
bits of the PFN or PFNX field of the Entry{Lo,Hi} register.
Fix this by detecting the number of fill bits present in the
Entry{Lo,Hi} registers & explicitly clearing the software bits where
necessary.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: linux-kernel@vger.kernel.org
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/11218/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The code in build_update_entries for 64 bit physical addresses on a
MIPS64 CPU and 32 bit physical addresses on a MIPS32 CPU is now
identical, with the exception of r4k bug workaround in the latter which
would simply not apply to the former. Remove the duplication and some
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: linux-kernel@vger.kernel.org
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/11216/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The cpu_has_rixi cases in build_update_entries are now identical to the
non-RIXI cases with the one exception of the r45k_bvahwbug case which is
hardcoded as never happening anyway & presumably was either missed from
the RIXI path or would never happen on a CPU with RIXI support. Remove
the redundant checks & duplication.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: linux-kernel@vger.kernel.org
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/11215/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Make use of build_convert_pte_to_entrylo in the RIXI cases within
build_update_entries rather than open-coding it 4 times.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: linux-kernel@vger.kernel.org
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/11214/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Removal started in commit 5bbeed12bd ("sparc32: drop unused
kmap_atomic_to_page"). Let's do it across the whole tree.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When debugging or examining the performance of a system it can be useful
to examine the effect of L2 prefetching. Provide an optional debugfs
entry to allow a user to enable or disable L2 prefetching.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11182/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
On systems with CM 2.5 & beyond there may be L2 prefetch units present
which are not enabled by default. Detect them, configuring & enabling
prefetching when available.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: linux-kernel@vger.kernel.org
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/11180/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Unsigned values cannot be lesser than zero.
The problem has been detected using proposed semantic patch
scripts/coccinelle/tests/unsigned_lesser_than_zero.cocci [1].
[ralf@linux-mips.org: Chris Dearman's original commit
9318c51acd ([MIPS] MIPS32/MIPS64 secondary
cache management) introduced these less than zero checks in 2.6.18.]
[1]: http://permalink.gmane.org/gmane.linux.kernel/2038576
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Cc: linux-kernel@vger.kernel.org
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: Chris Dearman <chris.dearman@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11165/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
If there is a DMA zone (usually 24bit = 16MB I believe), but no DMA32
zone, as is the case for some 32-bit kernels, then massage_gfp_flags()
will cause DMA memory allocated for devices with a 32..63-bit
coherent_dma_mask to fall back to using __GFP_DMA, even though there may
only be 32-bits of physical address available anyway.
Correct that case to compare against a mask the size of phys_addr_t
instead of always using a 64-bit mask.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Fixes: a2e715a86c ("MIPS: DMA: Fix computation of DMA flags from device's coherent_dma_mask.")
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: <stable@vger.kernel.org> # 2.6.36+
Patchwork: https://patchwork.linux-mips.org/patch/9610/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
MAARs should be initialised on each CPU (or rather, core) in the system
in order to achieve consistent behaviour & performance. Previously they
have only been initialised on the boot CPU which leads to performance
problems if tasks are later scheduled on a secondary CPU, particularly
if those tasks make use of unaligned vector accesses where some CPUs
don't handle any cases in hardware for non-speculative memory regions.
Fix this by recording the MAAR configuration from the boot CPU and
applying it to secondary CPUs as part of their bringup.
Reported-by: Doug Gilmore <doug.gilmore@imgtec.com>
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: David Hildenbrand <dahi@linux.vnet.ibm.com>
Cc: linux-kernel@vger.kernel.org
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: Hemmo Nieminen <hemmo.nieminen@iki.fi>
Cc: Alex Smith <alex.smith@imgtec.com>
Cc: Peter Zijlstra (Intel) <peterz@infradead.org>
Patchwork: https://patchwork.linux-mips.org/patch/11239/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Verifying that the MAAR configuration is as expected is useful when
debugging the performance of a system. Print out the memory regions
configured via MAAR along with their attributes.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: David Hildenbrand <dahi@linux.vnet.ibm.com>
Cc: linux-kernel@vger.kernel.org
Cc: Peter Zijlstra (Intel) <peterz@infradead.org>
Patchwork: https://patchwork.linux-mips.org/patch/11238/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
maar_init was previously only compiled when CONFIG_NEED_MULTIPLE_NODES
was not set, which has been fine since it is only called from the
standard implementation of mem_init which has the same condition. In
preparation for calling it from the SMP startup code on secondary CPUs,
move maar_init outside of the #ifndef such that it is always compiled.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: David Hildenbrand <dahi@linux.vnet.ibm.com>
Cc: linux-kernel@vger.kernel.org
Cc: Ingo Molnar <mingo@kernel.org>
Patchwork: https://patchwork.linux-mips.org/patch/11237/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Most architectures do not support non-coherent allocations and either
define dma_{alloc,free}_noncoherent to their coherent versions or stub
them out.
Openrisc uses dma_{alloc,free}_attrs to implement them, and only Mips
implements them directly.
This patch moves the Openrisc version to common code, and handles the
DMA_ATTR_NON_CONSISTENT case in the mips dma_map_ops instance.
Note that actual non-coherent allocations require a dma_cache_sync
implementation, so if non-coherent allocations didn't work on
an architecture before this patch they still won't work after it.
[jcmvbkbc@gmail.com: fix xtensa]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Chris Metcalf <cmetcalf@ezchip.com>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since 2009 we have a nice asm-generic header implementing lots of DMA API
functions for architectures using struct dma_map_ops, but unfortunately
it's still missing a lot of APIs that all architectures still have to
duplicate.
This series consolidates the remaining functions, although we still need
arch opt outs for two of them as a few architectures have very
non-standard implementations.
This patch (of 5):
The coherent DMA allocator works the same over all architectures supporting
dma_map operations.
This patch consolidates them and converges the minor differences:
- the debug_dma helpers are now called from all architectures, including
those that were previously missing them
- dma_alloc_from_coherent and dma_release_from_coherent are now always
called from the generic alloc/free routines instead of the ops
dma-mapping-common.h always includes dma-coherent.h to get the defintions
for them, or the stubs if the architecture doesn't support this feature
- checks for ->alloc / ->free presence are removed. There is only one
magic instead of dma_map_ops without them (mic_dma_ops) and that one
is x86 only anyway.
Besides that only x86 needs special treatment to replace a default devices
if none is passed and tweak the gfp_flags. An optional arch hook is provided
for that.
[linux@roeck-us.net: fix build]
[jcmvbkbc@gmail.com: fix xtensa]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Chris Metcalf <cmetcalf@ezchip.com>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The generic implementation of dma_map_ops.mmap(), dma_common_mmap(),
is not correct for non-coherent devices. It expects to be passed a
virtual address previously returned by dma_alloc_coherent(), which for
a non-coherent device will return a KSEG1 address. It then attempts to
convert that virtual address to a physical address using virt_to_page()
which will yield an incorrect address.
Also, dma_common_mmap() does not handle the DMA_ATTR_WRITE_COMBINE
attribute, and therefore dma_mmap_writecombine() will not actually set
the appropriate pgprot_t flags for write combining.
This patch adds an implementation of dma_map_ops.mmap() that correctly
handles KSEG1 addresses, and enables write combining when requested.
Signed-off-by: Alex Smith <alex.smith@imgtec.com>
Cc: Sadegh Abbasi <Sadegh.Abbasi@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/10808/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The TLB registers are dumped in a couble of places:
- sysrq_tlbdump_single() - when dumping TLB state.
- do_mcheck() - in response to a machine check error.
The main TLB registers also differ between r3k and r4k, but r4k appears
to be assumed.
Refactor this code into a dump_tlb_regs() function, implemented for both
r3k and r4k, and used by both of the above functions.
Fixes: d1e9a4f547 ("MIPS: Add SysRq operation to dump TLBs on all CPUs")
Suggested-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/10721/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Introduce a default weak implementation of platform_maar_init which
makes use of the data that platforms already provide to the bootmem
allocator. This should hopefully cover the most common configurations,
reduce the duplication of information provided by platforms & leaves
platforms with the option of providing a custom implementation if
required.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-kernel@vger.kernel.org
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Patchwork: https://patchwork.linux-mips.org/patch/10676/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Allow platforms to perform platform-specific steps before configuring
the L2 cache. This is necessary for platforms with CM3 since the L2
parameters no longer live in the Config2 register.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/10642/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Detect the L2 cache configuration from GCR_L2_CONFIG when a CM3 is
present in the system, rather than from Config2 which does not expose
the L2 configuration on I6400.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/10641/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add a CPU_I6400 case to various switch statements, doing the same thing
as for CPU_P5600.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/10635/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Execution of break instruction, trap instructions, emulation of unaligned
loads or floating point instructions - anything that tries to read the
instruction's opcode from userspace - needs read access to a page.
RIXI (Read Inhibit / Execute Inhibit) support however allows the creation of
pags that are executable but not readable. On such a mapping the attempted
load of the opcode by the kernel is going to cause an endless loop of
page faults.
The quick workaround for this is to disable the combinations that the kernel
currently isn't able to handle which are executable mappings.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The L2 cache in the I6400 core has 16 ways, so extend the way_string
array to take such caches into account.
[ralf@linux-mips.org: Other already supported CPUs are free to support
more than 8 ways of cache as well.]
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/10640/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
MT_SMP is not the only SMP option for MT cores. The MT_SMP option
allows more than one VPE per core to appear as a secondary CPU in the
system. Because of how CM works, it propagates the address-based
cache ops to the secondary cores but not the index-based ones.
Because of that, the code does not use IPIs to flush the L1 caches on
secondary cores because the CM would have done that already. However,
the CM functionality is independent of the type of SMP kernel so even in
non-MT kernels, IPIs are not necessary. As a result of which, we change
the conditional to depend on the CM presence. Moreover, since VPEs on
the same core share the same L1 caches, there is no need to send an
IPI on all of them so we calculate a suitable cpumask with only one
VPE per core.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: <stable@vger.kernel.org> # 3.15+
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/10654/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Pull MIPS updates from Ralf Baechle:
- Improvements to the tlb_dump code
- KVM fixes
- Add support for appended DTB
- Minor improvements to the R12000 support
- Minor improvements to the R12000 support
- Various platform improvments for BCM47xx
- The usual pile of minor cleanups
- A number of BPF fixes and improvments
- Some improvments to the support for R3000 and DECstations
- Some improvments to the ATH79 platform support
- A major patchset for the JZ4740 SOC adding support for the CI20 platform
- Add support for the Pistachio SOC
- Minor BMIPS/BCM63xx platform support improvments.
- Avoid "SYNC 0" as memory barrier when unlocking spinlocks
- Add support for the XWR-1750 board.
- Paul's __cpuinit/__cpuinitdata cleanups.
- New Malta CPU board support large memory so enable ZONE_DMA32.
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (131 commits)
MIPS: spinlock: Adjust arch_spin_lock back-off time
MIPS: asmmacro: Ensure 64-bit FP registers are used with MSA
MIPS: BCM47xx: Simplify handling SPROM revisions
MIPS: Cobalt Don't use module_init in non-modular MTD registration.
MIPS: BCM47xx: Move NVRAM driver to the drivers/firmware/
MIPS: use for_each_sg()
MIPS: BCM47xx: Don't select BCMA_HOST_PCI
MIPS: BCM47xx: Add helper variable for storing NVRAM length
MIPS: IRQ/IP27: Move IRQ allocation API to platform code.
MIPS: Replace smp_mb with release barrier function in unlocks.
MIPS: i8259: DT support
MIPS: Malta: Basic DT plumbing
MIPS: include errno.h for ENODEV in mips-cm.h
MIPS: Define GCR_GIC_STATUS register fields
MIPS: BPF: Introduce BPF ASM helpers
MIPS: BPF: Use BPF register names to describe the ABI
MIPS: BPF: Move register definition to the BPF header
MIPS: net: BPF: Replace RSIZE with SZREG
MIPS: BPF: Free up some callee-saved registers
MIPS: Xtalk: Update xwidget.h with known Xtalk device numbers
...
Currently we have many duplicates in definitions of huge_pmd_unshare. In
all architectures this function just returns 0 when
CONFIG_ARCH_WANT_HUGE_PMD_SHARE is N.
This patch puts the default implementation in mm/hugetlb.c and lets these
architectures use the common code.
Signed-off-by: Zhang Zhen <zhenzhang.zhang@huawei.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Chris Metcalf <cmetcalf@ezchip.com>
Cc: David Rientjes <rientjes@google.com>
Cc: James Yang <James.Yang@freescale.com>
Cc: Aneesh Kumar <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull scheduler updates from Ingo Molnar:
"The main changes are:
- lockless wakeup support for futexes and IPC message queues
(Davidlohr Bueso, Peter Zijlstra)
- Replace spinlocks with atomics in thread_group_cputimer(), to
improve scalability (Jason Low)
- NUMA balancing improvements (Rik van Riel)
- SCHED_DEADLINE improvements (Wanpeng Li)
- clean up and reorganize preemption helpers (Frederic Weisbecker)
- decouple page fault disabling machinery from the preemption
counter, to improve debuggability and robustness (David
Hildenbrand)
- SCHED_DEADLINE documentation updates (Luca Abeni)
- topology CPU masks cleanups (Bartosz Golaszewski)
- /proc/sched_debug improvements (Srikar Dronamraju)"
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (79 commits)
sched/deadline: Remove needless parameter in dl_runtime_exceeded()
sched: Remove superfluous resetting of the p->dl_throttled flag
sched/deadline: Drop duplicate init_sched_dl_class() declaration
sched/deadline: Reduce rq lock contention by eliminating locking of non-feasible target
sched/deadline: Make init_sched_dl_class() __init
sched/deadline: Optimize pull_dl_task()
sched/preempt: Add static_key() to preempt_notifiers
sched/preempt: Fix preempt notifiers documentation about hlist_del() within unsafe iteration
sched/stop_machine: Fix deadlock between multiple stop_two_cpus()
sched/debug: Add sum_sleep_runtime to /proc/<pid>/sched
sched/debug: Replace vruntime with wait_sum in /proc/sched_debug
sched/debug: Properly format runnable tasks in /proc/sched_debug
sched/numa: Only consider less busy nodes as numa balancing destinations
Revert 095bebf61a ("sched/numa: Do not move past the balance point if unbalanced")
sched/fair: Prevent throttling in early pick_next_task_fair()
preempt: Reorganize the notrace definitions a bit
preempt: Use preempt_schedule_context() as the official tracing preemption point
sched: Make preempt_schedule_context() function-tracing safe
x86: Remove cpu_sibling_mask() and cpu_core_mask()
x86: Replace cpu_**_mask() with topology_**_cpumask()
...
This replaces the plain loop over the sglist array with for_each_sg()
macro which consists of sg_next() function calls. Since MIPS doesn't
select ARCH_HAS_SG_CHAIN, it is not necessary to use for_each_sg() in
order to loop over each sg element. But this can help find problems
with drivers that do not properly initialize their sg tables when
CONFIG_DEBUG_SG is enabled.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: akpm@linux-foundation.org
Cc: linux-mips@linux-mips.org
Cc: linux-arch@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/9930/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit c5b367835c ("MIPS: Add support for XPA.") added generation of a
shift by _PAGE_PRESENT_SHIFT in build_pte_present() and
build_pte_writable(), however except for the XPA case this is always
zero making it unnecessary.
Make the shift conditional upon _PAGE_PRESENT_SHIFT being non-zero to
save an instruction in those cases.
Fixes: c5b367835c ("MIPS: Add support for XPA.")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9889/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
