Add the SYS-DMAC0 and SYS-DMAC1 clocks to the MSTP2 clock node. They
will be used by the upcoming DMAC DT nodes.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add device nodes for the R8A7790 internal PCI bridge devices.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Reviewed-by: Ian Molton <ian.molton@codethink.co.uk>
[Sergei: added several properties to the PCI bridge nodes]
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds a default PCIe bus clock node.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds the device tree clock node for the PCIe Controller
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch support PIO transfer only at this point
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add needed information inside CPU0 for the generic cpufreq-cpu0 driver.
- voltage-tolerance = 1%
It reflects the tolerance for the CPU voltage defined inside the OPP
table. Due to the lack of proper OPP definition, use an arbitrary safe
value.
- clock-latency = 300 us
Approximate worst-case latency to do a full DVFS transition for every
OPPs. Due to the lack of HW information, use an arbitrary safe value.
Note: The term transition-latency will be more accurate to define this
value since the clock transition latency is not the only parameter that
will define the overall DVFS transition.
- operating-points = < kHz - uV >
List of 6 operating points. All of them are using the same voltage
since the valid Vmin voltage is not documented in the HW spec.
- clocks
phandle to the CPU clock source. This clock source is used for all the
4 CortexA15 located inside the same cluster.
Signed-off-by: Benoit Cousson <bcousson+renesas@baylibre.com>
[gaku.inami.xw@bp.renesas.com: Change the setting of OPPs for ES2.0]
Signed-off-by: Gaku Inami <gaku.inami.xw@bp.renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As with previous release, this continues to be among the largest branches
we merge, with lots of new contents.
New things for this release are among other things:
- DTSI contents for the new SoCs supported in 3.16 (see SoC pull request)
- Qualcomm APQ8064 and APQ8084 SoCs and eval boards
- Nvidia Jetson TK1 development board (Tegra T124-based)
Two new SoCs that didn't need enough new platform code to stand out
enough for me to notice when writing the SoC tag, but that adds new DT
contents are:
- TI DRA72
- Marvell Berlin 2Q
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=OvOG
-----END PGP SIGNATURE-----
Merge tag 'dt-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc into next
Pull ARM SoC devicetree updates from Olof Johansson:
"As with previous release, this continues to be among the largest
branches we merge, with lots of new contents.
New things for this release are among other things:
- DTSI contents for the new SoCs supported in 3.16 (see SoC pull request)
- Qualcomm APQ8064 and APQ8084 SoCs and eval boards
- Nvidia Jetson TK1 development board (Tegra T124-based)
Two new SoCs that didn't need enough new platform code to stand out
enough for me to notice when writing the SoC tag, but that adds new DT
contents are:
- TI DRA72
- Marvell Berlin 2Q"
* tag 'dt-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (500 commits)
ARM: dts: add secure firmware support for exynos5420-arndale-octa
ARM: dts: add pmu sysreg node to exynos3250
ARM: dts: correct the usb phy node in exynos5800-peach-pi
ARM: dts: correct the usb phy node in exynos5420-peach-pit
ARM: dts: add dts files for exynos5410 and exynos5410-smdk5410
ARM: dts: add dts files for exynos3250 SoC
ARM: dts: add mfc node for exynos5800
ARM: dts: add Vbus regulator for USB 3.0 on exynos5800-peach-pi
ARM: dts: enable fimd for exynos5800-peach-pi
ARM: dts: enable display controller for exynos5800-peach-pi
ARM: dts: enable hdmi for exynos5800-peach-pi
ARM: dts: add dts file for exynos5800-peach-pi board
ARM: dts: add dts file for exynos5800 SoC
ARM: dts: add dts file for exynos5260-xyref5260 board
ARM: dts: add dts files for exynos5260 SoC
ARM: dts: update watchdog node name in exynos5440
ARM: dts: use key code macros on Origen and Arndale boards
ARM: dts: enable RTC and WDT nodes on Origen boards
ARM: dts: qcom: Add APQ8084-MTP board support
ARM: dts: qcom: Add APQ8084 SoC support
...
Signed-off-by: Wolfram Sang <wsa@sang-engineering.com>
[horms+renesas@verge.net.au resolved conflicts]
[horms+renesas@verge.net.au consistently use space as separator]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
All I2C clocks derive from the HP clock, not from the P clock. Fix them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Wolfram Sang <wsa@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Prepare for the advent of MSIOF SPI, which will be spi1 to spi4.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The r8a7790 has four VSP1 instances, two of them being named VSPS (which
stands for "VSP Standard") and VSPR (which stands for "VSP for
Resizing"). The clock section in the SoC datasheet misunderstood the
abbreviations as meaning VSP System and VSP Realtime, and named the
corresponding clocks VSP1(SY) and VSP1(RT). This mistake has been
carried over to the kernel code.
Fix this by renaming the VSP1_SY and VSP1_RT clocks to VSP1_S and VSP1_R.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
These changes are mostly for ARM specific device drivers that either
don't have an upstream maintainer, or that had the maintainer ask
us to pick up the changes to avoid conflicts. A large chunk of this
are clock drivers (bcm281xx, exynos, versatile, shmobile), aside from
that, reset controllers for STi as well as a large rework of the
Marvell Orion/EBU watchdog driver are notable.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=u/FI
-----END PGP SIGNATURE-----
Merge tag 'drivers-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver changes from Arnd Bergmann:
"These changes are mostly for ARM specific device drivers that either
don't have an upstream maintainer, or that had the maintainer ask us
to pick up the changes to avoid conflicts.
A large chunk of this are clock drivers (bcm281xx, exynos, versatile,
shmobile), aside from that, reset controllers for STi as well as a
large rework of the Marvell Orion/EBU watchdog driver are notable"
* tag 'drivers-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (99 commits)
Revert "dts: socfpga: Add DTS entry for adding the stmmac glue layer for stmmac."
Revert "net: stmmac: Add SOCFPGA glue driver"
ARM: shmobile: r8a7791: Fix SCIFA3-5 clocks
ARM: STi: Add reset controller support to mach-sti Kconfig
drivers: reset: stih416: add softreset controller
drivers: reset: stih415: add softreset controller
drivers: reset: Reset controller driver for STiH416
drivers: reset: Reset controller driver for STiH415
drivers: reset: STi SoC system configuration reset controller support
dts: socfpga: Add sysmgr node so the gmac can use to reference
dts: socfpga: Add support for SD/MMC on the SOCFPGA platform
reset: Add optional resets and stubs
ARM: shmobile: r7s72100: fix bus clock calculation
Power: Reset: Generalize qnap-poweroff to work on Synology devices.
dts: socfpga: Update clock entry to support multiple parents
ARM: socfpga: Update socfpga_defconfig
dts: socfpga: Add DTS entry for adding the stmmac glue layer for stmmac.
net: stmmac: Add SOCFPGA glue driver
watchdog: orion_wdt: Use %pa to print 'phys_addr_t'
drivers: cci: Export CCI PMU revision
...
Define the generic R8A7790 part of the Ether device node.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Current audio clock doesn't have dependency to device/driver,
but, it is not good design for DT support.
To avoid branch merge conflict issue,
it uses this load map, and this patch is 1) part.
1) add old/new style clock in platform
2) add new style clock method in driver
3) remove old tyle clock from platform
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa@sang-engineering.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
These values are inherited, so don't need to be specified again.
Signed-off-by: Wolfram Sang <wsa@sang-engineering.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Replace the hardcoded value 4 with IRQ_TYPE_LEVEL_HIGH.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Remove the -generic suffix that has been added by mistake from the
serial port compatible strings.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This adds SATA[01] device nodes to r8a7790.dtsi
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The platform code serial port instantiation mechanism is kept for the
non-DT platforms only.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Correct i2c clock references for r8a7790 (R-Car H2) SoC
The error was introduced in 72197ca7a1 ("ARM: shmobile: r8a7790:
Reference clocks") which is queued up for v3.14.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=UVOK
-----END PGP SIGNATURE-----
Merge tag 'renesas-dt-fixes2-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes
Second Round of Renesas ARM Based SoC DT Fixes for v3.14
Correct i2c clock references for r8a7790 (R-Car H2) SoC
The error was introduced in 72197ca7a1 ("ARM: shmobile: r8a7790:
Reference clocks") which is queued up for v3.14.
* tag 'renesas-dt-fixes2-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r8a7790.dtsi: ficx i2c[0-3] clock reference
Signed-off-by: Olof Johansson <olof@lixom.net>
DT and DT-conversion-related changes for various ARM platforms. Most
of these are to enable various devices on various boards, etc, and not
necessarily worth enumerating.
New boards and systems continue to come in as new devicetree files that
don't require corresponding C changes any more, which is indicating that
the system is starting to work fairly well.
A few things worth pointing out:
* ST Ericsson ux500 platforms have made the major push to move over to fully
support the platform with DT.
* Renesas platforms continue their conversion over from legacy platform devices
to DT-based for hardware description.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJS4Vg8AAoJEIwa5zzehBx3tRkP/2dXiXerdB6V63HQ2UjA0J1w
wnEqOrHXhIBPHVsAjRs+JOqG1iHxwQ+6qPtpxy//OZy5EN/hTamU5HBAKwcJvbbS
He+a2xhOK6nsjr5QrEk2wupXOodhXDXoaU2mqJ51HAN9AOS68QVbHFh1jHs0f7S0
RaPVqHTlpXiiWMZ1ScVwl6qqM/hVcK6H3WOrHz09RWG2V/rFth4cJ6hkXBgqBeYU
Zl24Z9mzStaTI7epDEZXq7jZTMX5lzArL2mCA0jKA+YdEy7KSh5GEzqDGu2qi230
wwmJ3g5X1WxDvedXPL0+gUffL7UcHWlEV1nl5KtwVsPf/vpsAUvwPLdlObUgA2nr
/cVrdwQYLaPJKg6xq8IWxaS0K34kLdJyUwiNjKxw5s2GayWEwqGRWALn9TANdKz7
Wg+RT0UxjHPL8zj/N1uQV/fTdayHE6PnTPorESKDK0a6q9qqzdUypV3j13d9faIS
FbASmq35zO2iOo4ji7SX6wP4ZwPWV1Yx9UBl4RNDlWu9MyB6jsjiJFT1nyr5PxGo
WCf8U1Nv4tqCo01gE8AHR1qzlW7cOoya7VMTwDme6J5N9K3GpN+OXqCVItT1lfL2
s2I0OI6TiD7pTAM4WkgCZaKAhPaE/i2Vc9xlGdZ8L77J4allBtLXTAPpIAZj1Lfl
a7NT9hbUIiEkTnO8BhHm
=4o2d
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC DT updates from Olof Johansson:
"DT and DT-conversion-related changes for various ARM platforms. Most
of these are to enable various devices on various boards, etc, and not
necessarily worth enumerating.
New boards and systems continue to come in as new devicetree files
that don't require corresponding C changes any more, which is
indicating that the system is starting to work fairly well.
A few things worth pointing out:
* ST Ericsson ux500 platforms have made the major push to move over
to fully support the platform with DT
* Renesas platforms continue their conversion over from legacy
platform devices to DT-based for hardware description"
* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (327 commits)
ARM: dts: SiRF: add pin group for USP0 with only RX or TX frame sync
ARM: dts: SiRF: add lost usp1_uart_nostreamctrl pin group for atlas6
ARM: dts: sirf: add lost minigpsrtc device node
ARM: dts: sirf: add clock, frequence-voltage table for CPU0
ARM: dts: sirf: add lost bus_width, clock and status for sdhci
ARM: dts: sirf: add lost clocks for cphifbg
ARM: dts: socfpga: add pl330 clock
ARM: dts: socfpga: update L2 tag and data latency
arm: sun7i: cubietruck: Enable the i2c controllers
ARM: dts: add support for EXYNOS4412 based TINY4412 board
ARM: dts: Add initial support for Arndale Octa board
ARM: bcm2835: add USB controller to device tree
ARM: dts: MSM8974: Add MMIO architected timer node
ARM: dts: MSM8974: Add restart node
ARM: dts: sun7i: external clock outputs
ARM: dts: sun7i: Change 32768 Hz oscillator node name to clk@N style
ARM: dts: sun7i: Add pin muxing options for clock outputs
ARM: dts: sun7i: Add rtp controller node
ARM: dts: sun5i: Add rtp controller node
ARM: dts: sun4i: Add rtp controller node
...
The R8A7790's dtsi file i2c0, i2c1, i2c2, and i2c3 nodes have clock
references to the mstp3_clks clock node, however these clocks are in the
mstp9_clks node.
The error was introducted in 72197ca7a1 ("ARM: shmobile: r8a7790:
Reference clocks") which is in Simon's current development tree.
This patch fixes the following error:
of_clk_src_onecell_get: invalid clock index 31
i2c-rcar e6508000.i2c: cannot get clock
i2c-rcar: probe of e6508000.i2c failed with error -2
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This reverts commit 6dea2c1ebc.
Unfortunately this commit prevents multiplatform from booting to
the point where a serial console is available. Revert it while
a solution is sought.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reference clocks using a "clocks" property in all nodes corresponding to
devices that require a clock.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Declare all core clocks and DIV6 clocks, as well as all MSTP clocks
currently used by r8a7790 boards.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The r8a7790.dtsi file has four sdhi nodes which the first two have the wrong
resource size for their register block. This causes the sh_modbile_sdhi driver
to fail to communicate with card at-all.
Change sdhi{0,1} node size from 0x100 to 0x200 to correct these nodes
as per Kuninori Morimoto's response to the original patch where all four
nodes where changed. sdhi{2,3} are the correct size.
This bug has been present since sdhi resources were added to the r8a7790 by
8c9b1aa418 ("ARM: shmobile: r8a7790: add MMCIF and SDHI DT
templates") in v3.11-rc2.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Tested-by: William Towle <william.towle@codethink.co.uk>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add "renesas,irqc-r8a7790" to the compatible string for IRQC
in case of r8a7790. This makes the IRQC follow the same style
as the other devices and also makes it more future proof.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add "renesas,mmcif-r8a7790" to the compatible string for MMCIF
in case of r8a7790. This makes the MMCIF follow the same style
as the other devices and also makes it more future proof.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Hook up the r8a7790 thermal sensor to the DTS.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
According to ePAPR spec,
this patch tidies up DT node name and related clock.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The r8a7790 GPIO resources are currently incorrect. Fix that
by making them match the English r8a7790 v0.6 data sheet.
Tested with GPIO LED using Lager DT reference.
This problem has been present since GPIOs were added to the r8a7790 SoC by
f98e10c88a ("ARM: shmobile: r8a7790: Add GPIO controller devices to
device tree") in v3.12-rc1.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
- Always build in board-generic, and add pdata quirks and auxdata
support for it so we have all the pdata related quirks
in the same place.
- Merge of the drivers/pinctrl changes that are needed for PM
to continue working on omap3 and also needed for other omaps
eventually. The three pinctrl related patches have been acked
by Linus Walleij and are pulled into both the pinctrl tree
and this branch.
- Few defconfig related changes for drivers needed.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQIcBAABAgAGBQJSWIMoAAoJEBvUPslcq6VzudIQAKVjdFI26yxmI3xpYjNVS2P8
JWaUTTjHAR7Lc0EWwtuGj6CqCtbNXUH1bTnChQrkzhT7fPMGQGFbgErnoaYQdwwJ
qI15T7qcwy4q54vzeaOMAUS9UNZzr4lChEvxt9uYNoEhHlu7i6/ntyk5fgRfHMsh
yK439VA7W/2rLNinpUmIAghx6+gUuRIBbVtfJ71gg5roXL7fY2hYizEoIkDKqWSD
i1F24Xt33LAjNhy3n4/6JxCldee7ib2z0YrOUOrTdXWh/L1G9tDTslkdga6rAA5c
A+B4nP7zP7i9c1SlTPbwRyguwjHhfSPuNTRhyhuePbwVk4bscglQZx8A7dH8BwS0
pSCUxCTe2+CPEEzeN/ee9TgXwyX9Ab/r5BM092xFrX2lBbV3KxPl1F7rAxJ4HQTu
Bh/M5bnKGupO7H9MOKqmLAf1y3a3JCrXVUuQljDMJnvauB8QFTx0nYQvZ/bQCJLZ
/wfADHtooJ/FGHFS7Vb+HSLX7ifF2HyES9FgnQag5H77VfXS+bqI5yHsTcYHTgP1
MlW8mObg0vJ+oUuowhhrk9pzQ1l1VFIaMqOKOouL3X6GHAHFiBSCti1fRiSE7d4U
feW7a0NSyIjue+MAwxCjSLXOpHCATgnQ1mp9s8ByD0IF98iPugpnp9d6NGH/wp9A
bgK7SGeOWXGoc+kN672c
=bqsS
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.13/quirk-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
From Tony Lindgren:
Changes needed to prepare for making omap3 device tree only:
- Always build in board-generic, and add pdata quirks and auxdata
support for it so we have all the pdata related quirks
in the same place.
- Merge of the drivers/pinctrl changes that are needed for PM
to continue working on omap3 and also needed for other omaps
eventually. The three pinctrl related patches have been acked
by Linus Walleij and are pulled into both the pinctrl tree
and this branch.
- Few defconfig related changes for drivers needed.
* tag 'omap-for-v3.13/quirk-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (523 commits)
ARM: configs: omap2plus_defconfig: enable dwc3 and dependencies
ARM: OMAP2+: Add WLAN modules and of_serial to omap2plus_defconfig
ARM: OMAP2+: Run make savedefconfig on omap2plus_defconfig to shrink it
ARM: OMAP2+: Add minimal 8250 support for GPMC
ARM: OMAP2+: Use pdata quirks for wl12xx for omap3 evm and zoom3
ARM: OMAP: Move DT wake-up event handling over to use pinctrl-single-omap
ARM: OMAP2+: Add support for auxdata
pinctrl: single: Add support for auxdata
pinctrl: single: Add support for wake-up interrupts
pinctrl: single: Prepare for supporting SoC specific features
ARM: OMAP2+: igep0020: use display init from dss-common
ARM: OMAP2+: pdata-quirks: add legacy display init for IGEPv2 board
+Linux 3.12-rc4
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Add DT nodes for the four I2C interfacces on r8a7790.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
