On ISOC transfer completion, in DDMA mode, set actual frame
number returning to function driver in usb_request.
Due to core limitation, returning frame number is 11-bit wide.
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Some function drivers queueing more than 128 ISOC requests at a time.
To avoid "descriptor chain full" cases, increasing descriptors count
from MAX_DMA_DESC_NUM_GENERIC to MAX_DMA_DESC_NUM_HS_ISOC for ISOC's
only.
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Added delayed status support for Control transfers.
Tested in all 3 modes: Slave, BDMA and DDMA.
Performed tests: USB CV (Ch9 and MSC), Control Read/Write tests
using Synopsys USB test environment function driver.
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Most of the phy initialization is shared between host and gadget,
this adds the turnaround configuration only used by gadgets to
the global phy init.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Jules Maselbas <jmaselbas@kalray.eu>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The phy utmi width information is already set in hsotg params,
phyif is only used in few places and I don't see any reason to
not use hsotg's params.
Moreover the utmi width was being forced to 16 bits by platform
initialization which doesn't take in account HW configuration.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Jules Maselbas <jmaselbas@kalray.eu>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The function dwc2_hsotg_init is only called once just before calling
dwc2_hsotg_core_init_disconnected which does the same initialization:
setting the usbcfg register with turnaround time, timeout calibration
and phy width.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Jules Maselbas <jmaselbas@kalray.eu>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Avoiding switch to L1 state in any stage of control transfers.
Send NYET handshake to LPM token.
Renamed GLPMCFG_LPM_ACCEPT_CTRL_ISOC to GLPMCFG_LPM_REJECT_CTRL_CONTROL
because by setting this bit core reject LPM token.
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch adds support for transferring requests, which are
non-contiguous in physical memory, i.e. the data buffer is described by
a scatter-list. This allows transferring large requests without relying
on error-prone contiguous buffer allocations. This way of allocating
requests is already implemented in functionfs and TCM USB functions and
automatically used if UDC driver advertises scatter-gather suppport.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
[mszyprow: fixed null pointer issue, rewrote commit message]
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In case when some EP IN is frequently reused, i.e. enabled/disabled by
function driver. It is required to clear TxFIFO number field in DIEPCTL
register before setting new number. Otherwise there is probability to
have same TxFIFO number for different EP's because of OR operator.
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
To clear GINTSTS2_WKUP_ALERT_INT bit in GINTSTS2 register
require to write 1. This bit is implemented as "Write to clear".
Fixes: 187c5298a1 ("usb: dwc2: gadget: Add handler for WkupAlert interrupt")
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Disabling all EP's allow to reset EP's to initial state.
Introduced new function dwc2_hsotg_ep_disable_lock() which
before calling dwc2_hsotg_ep_disable() function acquire
hsotg->lock and release on exiting.
From dwc2_hsotg_ep_disable() function removed acquiring
hsotg->lock.
In dwc2_hsotg_core_init_disconnected() function when USB
reset interrupt asserted disabling all ep’s by
dwc2_hsotg_ep_disable() function.
This updates eliminating sparse imbalance warnings.
Reverted changes in dwc2_hostg_disconnect() function.
Introduced new function dwc2_hsotg_ep_disable_lock().
Changed dwc2_hsotg_ep_ops. Now disable point to
dwc2_hsotg_ep_disable_lock() function.
In functions dwc2_hsotg_udc_stop() and dwc2_hsotg_suspend()
dwc2_hsotg_ep_disable() function replaced by
dwc2_hsotg_ep_disable_lock() function.
In dwc2_hsotg_ep_disable() function removed acquiring
of hsotg->lock.
Fixes: dccf1bad4b ("usb: dwc2: Disable all EP's on disconnect")
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Set GLPMCFG_LPM_ACCEPT_CTRL_ISOC bit in GLPMCFG register
to accept LPM token during ISOC transfers when TxFIFO is
not empty.
- Added two definitions.
#define GLPMCFG_LPM_ACCEPT_CTRL_CONTROL BIT(21)
#define GLPMCFG_LPM_ACCEPT_CTRL_ISOC BIT(22)
This patch uses GLPMCFG_LPM_ACCEPT_CTRL_ISOC.
GLPMCFG_LPM_ACCEPT_CTRL_CONTROL is defined for further use.
- Added setting GLPMCFG_LPM_ACCEPT_CTRL_ISOC bit in GLPMCFG
register in dwc2_gadget_init_lpm function.
Signed-off-by: Artur Petrosyan <arturp@synopsys.com>
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
According to the databook DCTL_RMTWKUPSIG bit
is defined in DCTL register not in DCFG.
Updated setting DCTL_RMTWKUPSIG bit to DCTL
register.
Fixes: 187c5298a1 ("usb: dwc2: gadget: Add handler for WkupAlert interrupt")
Signed-off-by: Artur Petrosyan <arturp@synopsys.com>
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Added interrupt handler for WkupAlert interrupt.
This interrupt should initiate Remote Wake up.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
WKUP_ALERT interrupt should be unmask when lpm mode is enabled.
This interrupt is asserted when the device is in L1 for the duration
mentioned in GREFCLK.SOF_CNN_WKUP_ALERT. This is used to alert SW to
initiate Remote wake up so that the device resumes in time in order not
to lose sync with the host frame number.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Added dwc2_gadget_program_ref_clk function to program GREFCLK
register in device mode.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In service interval based scheduling target (u)frame must be
set as a last frame in this the service interval.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Added dwc2_gadget_dec_frame_num_by_one() function in gadget.c.
This function will be used to calculate descriptor frame number field
value. For service interval mode frame number in descriptor should point
to last (u)frame in the interval.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Added core parameter for service interval based scheduling.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Disabling all EP's allow to reset EP's to initial state.
On disconnect disable all EP's instead of just killing
all requests. Because of some platform didn't catch
disconnect event, same stuff added to
dwc2_hsotg_core_init_disconnected() function when USB
reset detected on the bus.
Changed from version 1:
Changed lock acquire flow in dwc2_hsotg_ep_disable()
function.
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Not a big pull request with only 37 non-merge commits, most of which
are touching dwc2 (74% of the changes).
The most important changes are dwc2's support for uframe scheduling
and its endian-agnostic readl/writel wrappers.
From dwc3 side we have a special new glue layer for Synopsys HAPS
which will help Synopsys running FPGA validation using our upstream
driver. We also have the beginnings of dual-role support for Intel
Merrifield platform.
Apart from these, just a series of non-critical changes.
-----BEGIN PGP SIGNATURE-----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=HiNz
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: changes for v4.19
Not a big pull request with only 37 non-merge commits, most of which
are touching dwc2 (74% of the changes).
The most important changes are dwc2's support for uframe scheduling
and its endian-agnostic readl/writel wrappers.
From dwc3 side we have a special new glue layer for Synopsys HAPS
which will help Synopsys running FPGA validation using our upstream
driver. We also have the beginnings of dual-role support for Intel
Merrifield platform.
Apart from these, just a series of non-critical changes.
To start ISOC transfers in handlers dwc2_gadget_handle_nak() and
dwc2_gadget_handle_out_token_ep_disabled() driver reads current frame
number, based on which, set target frame number to start first ISOC
transfer.
In case if system's high IRQ latency and multiple EP's asserted
interrupt in same frame, there are high probability that when reading
current frame number in EP's handlers, actual frame number can be
increased. As result for bInterval > 1, starting target frame
will be set wrongly and all ISOC packets will be dropped.
In patch "usb: dwc2: Change reading of current frame number flow"
reading of current frame number done ASAP in common interrupt handler.
This frame number stored in frame_number variable which used as
starting frame number for ISOC EP's in above mentioned handlers.
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
dwc2_readl_rep/dwc2_writel_rep functions using readl/writel in a
loop.
Signed-off-by: Gevorg Sahakyan <sahakyan@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Added hsotg argument to dwc2_readl/writel function prototype,
and also instead of address pass offset of register.
hsotg will contain flag field for endianness.
Also customized dwc2_set_bit and dwc2_clear_bit function for
dwc2_readl/writel functions.
Signed-off-by: Gevorg Sahakyan <sahakyan@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
For unidirectional endpoints, the endpoint pointer will be NULL for the
unused direction. Check that the endpoint is active before
dereferencing this pointer.
Fixes: 1b4977c793 ("usb: dwc2: Update dwc2_handle_incomplete_isoc_in() function")
Fixes: 689efb2619 ("usb: dwc2: Update dwc2_handle_incomplete_isoc_out() function")
Fixes: d84845522d ("usb: dwc2: Update GINTSTS_GOUTNAKEFF interrupt handling")
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
PID bitfield in descriptor should be set based on particular request
length, not based on EP's mc value. PID value can't be set to 0 even
request length is 0.
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Freed allocated request for ep0 to prevent memory leak in case when
dwc2_driver_probe() failed.
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In ISOC OUT transfer, when the OUT token received while EP disabled,
we shouldn't complete a usb request. The current flow completed one
usb request, this will lead to a packet drop to function driver.
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In ISOC transfer, when the NAK interrupt happens, we shouldn't complete
a usb request, the current flow will complete one usb request with no
hardware transfer, this will lead to a packet drop on the usb bus.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Zeng Tao <prime.zeng@hisilicon.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In case of requests queue is empty reset EP target_frame to
initial value.
This allow restarting ISOC traffic in case when function
driver queued requests with interruptions.
Tested-by: Zeng Tao <prime.zeng@hisilicon.com>
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
By clearing NAK status of EP, core will send ZLP
to IN token and assert NAK interrupt relying
on TxFIFO status only.
The WA applies only to core versions from 2.72a
to 4.00a (including both). Also for FS_IOT_1.00a
and HS_IOT_1.00a.
Signed-off-by: Artur Petrosyan <arturp@synopsys.com>
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Added descriptions for all not described parameters.
Fix all kernel doc's warnings.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The current frame_number is read from core for both
device and host modes. Reading of the current frame
number needs to be performed ASAP due to IRQ latency's.
This is why, it is moved to common interrupt handler.
Accordingly updated dwc2_gadget_target_frame_elapsed()
function which uses stored frame_number instead of
reading frame number.
In cases when target frame value is incremented
the frame_number is required to read again.
Signed-off-by: Artur Petrosyan <arturp@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Crash caused by going out of "eps_out" array range.
Iteration on "eps_out" changed to less than "num_of_eps".
Signed-off-by: Artur Petrosyan <arturp@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Added GHWCFG4_IPG_ISOC_SUPPORTED and DCFG_IPG_ISOC_SUPPORDED
bits definitions to enable/disable IPG feature.
Added ipg_isoc_en core parameter which will indicate IPG support
enable/disable and initialize it.
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In DDMA mode required to enable BNA interrupt for
both directions.
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Changed existing two descriptor-chain flow to one chain.
In two-chain implementation BNA interrupt used for switching between
two chains. BNA interrupt asserted because of returning to
beginning of the chain based on L-bit of last descriptor.
Because of that we lose packets. This issue resolved by using one
desc-chain.
Removed all staff related to two desc-chain flow from
DDMA ISOC related functions.
Removed request length checking from dwc2_gadget_fill_isoc_desc()
function. Request length checking added to dwc2_hsotg_ep_queue()
function. If request length greater than descriptor limits then
request not added to queue. Additional checking done for High
Bandwidth ISOC OUT's which not supported by driver. In
dwc2_gadget_fill_isoc_desc() function also checked desc-chain
status (full or not) to avoid of reusing not yet processed
descriptors.
In dwc2_gadget_start_isoc_ddma() function creation of desc-chain
always started from descriptor 0. Before filling descriptors, they
were initialized by HOST BUSY status.
In dwc2_gadget_complete_isoc_request_ddma() added checking for
desc-chain rollover. Also added checking completion status.
Request completed successfully if DEV_DMA_STS is DEV_DMA_STS_SUCC,
otherwise complete with actual=0. For systems with high IRQ latency
added pointer compl_desc to next descriptor to be completed by
XferCompl interrupt. This pointer replace descriptor index calculation
based on DxEPDMA register. On descriptor completion interrupt
processing all descriptors starting from compl_desc till descriptor
which Buffer Status field not equal DMA_DONE status.
Actually removed dwc2_gadget_start_next_isoc_ddma() function because
now driver use only one desc-chain and instead that function added
dwc2_gadget_handle_isoc_bna() function for handling BNA interrupts.
Handling BNA interrupt done by flushing TxFIFOs for OUT EPs,
completing request with actual=0 and resetting desc-chain number and
target frame to initial values for restarting transfers.
On handling NAK request completed with actual=0. Incremented target
frame to allow fill desc chain and start transfers.
In DDMA mode avoided of frame number incrementing, because tracking
of frame number performed in dwc2_gadget_fill_isoc_desc() function.
When core assert XferCompl along with BNA, we should ignore XferCompl
in dwc2_hsotg_epint() function.
On BNA interrupt replaced dwc2_gadget_start_next_isoc_ddma() by above
mentioned BNA handler.
In dwc2_hsotg_ep_enable() function added sanity check of bInterval
for ISOC IN in DDMA mode, because HW doesn't supported EP's with
bInterval more than 10 and check for mc for ISOC OUT transfers,
because core doesn't support high bandwidth transfers.
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add host/device hibernation functions which must be wrapped
by core's dwc2_enter_hibernation()/dwc2_exit_hibernation()
functions.
Make dwc2_backup_global_registers dwc2_restore_global_register
non-static to use them in both host/gadget sides.
Added function names:
dwc2_gadget_enter_hibernation()
dwc2_gadget_exit_hibernation()
dwc2_host_enter_hibernation()
dwc2_host_exit_hibernation()
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Artur Petrosyan <arturp@synopsys.com>
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
It will be set once corresponding set_feature command comes.
True if device is allowed to wake-up host by remote-wakeup
signalling.
This is preparation for remote wake-up support implementation,
it will not be implemented until gadget stack provide interface
for bringing remote wake-up signalling.
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add parameter remote_wakeup to dwc2_restore_device_registers()
to be able to restore device registers according to programming
guide for dwc-otg. It says that in case of rem_wakeup DCTL must not
be restored here.
Remove setting of DCTL_PWRONPRGDONE from this function, because it
will be done in function responsible for exiting from hibernation.
WA for enabled EPx's IN and OUT in DDMA mode. On entering to
hibernation wrong value read and saved from DIEPDMAx,
as result BNA interrupt asserted on hibernation exit
by restoring from saved area.
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Artur Petrosyan <arturp@synopsys.com>
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Moved dtxfsiz from dwc2_gregs_backup to dwc2_dregs_backup,
because it is device register.
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
No-op change, only rename.
This code was misnamed originally. It was only responsible for partial
power down and not for hibernation.
Rename core_params->hibernation to core_params->power_down,
dwc2_set_param_hibernation() to dwc2_set_param_power_down().
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Set 'lpm_capable' flag in the gadget structure so
indicating that LPM is supported.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Sevak Arakelyan <sevaka@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Assign true or false to boolean variables instead of an integer value.
This issue was detected with the help of Coccinelle.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Added core state checking in dwc2_hsotg_ep_queue() function
to make sure that application will submit requests only in L0 state.
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Configure core in device mode to support LPM according to
programming guide.
Device will start giving valid responses for LPM tokens.
After this patch device side LPM will start working.
Signed-off-by: Sevak Arakelyan <sevaka@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Added function for supporting Active Clock Gating functionality
in the driver.
PCGCCTL1 (Power and Clock Control) register will be used
for controlling the core`s active clock gating feature, and
the previously reserved 12th bit in GHWCFG4 now indicates that the
controller supports the Dynamic Power Reduction (Active Clock Gating)
during no traffic scenarios such as L0, idle, resume and suspend
states.
dwc2_enable_acg() function sets GATEEN bit in PCGCCTL1 register
and enables ACG, if it supported.
According to ACG functional specification, enabling of ACG feature
in host mode done in host initialization, before turning Vbus on,
specifically in dwc2_core_host_init function.
Enabling of ACG feature in device mode done in device initialization,
before clearing the SftDiscon bit in DCTL.
This bit was cleared in dwc2_hsotg_core_connect() function.So
dwc2_enable_acg() called before dwc2_core_connect() calls.
Signed-off-by: Razmik Karapetyan <razmik@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Renamed __orr32 and __bic32 function names to more descriptive
dwc2_set_bit and dwc2_clear_bit respectively.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Razmik Karapetyan <razmik@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Disabled only unmasked endpoints based on DAINTMSK register.
This will allow to minimize GINTSTS_GOUTNAKEFF interrupt handling.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Razmik Karapetyan <razmik@synopsys.com>
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>