When commit 9c7be59fc5 ("libata: Apply NOLPM quirk to Crucial MX100
512GB SSDs") was added it inherited the ATA_HORKAGE_NO_NCQ_TRIM quirk
from the existing "Crucial_CT*MX100*" entry, but that entry sets model_rev
to "MU01", where as the entry adding the NOLPM quirk sets it to NULL.
This means that after this commit we no apply the NO_NCQ_TRIM quirk to
all "Crucial_CT512MX100*" SSDs even if they have the fixed "MU02"
firmware. This commit splits the "Crucial_CT512MX100*" quirk into 2
quirks, one for the "MU01" firmware and one for all other firmware
versions, so that we once again only apply the NO_NCQ_TRIM quirk to the
"MU01" firmware version.
Fixes: 9c7be59fc5 ("libata: Apply NOLPM quirk to ... MX100 512GB SSDs")
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Commit b17e5729a6 ("libata: disable LPM for Crucial BX100 SSD 500GB
drive"), introduced a ATA_HORKAGE_NOLPM quirk for Crucial BX100 500GB SSDs
but limited this to the MU02 firmware version, according to:
http://www.crucial.com/usa/en/support-ssd-firmware
MU02 is the last version, so there are no newer possibly fixed versions
and if the MU02 version has broken LPM then the MU01 almost certainly
also has broken LPM, so this commit changes the quirk to apply to all
firmware versions.
Fixes: b17e5729a6 ("libata: disable LPM for Crucial BX100 SSD 500GB...")
Cc: stable@vger.kernel.org
Cc: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
There have been reports of the Crucial M500 480GB model not working
with LPM set to min_power / med_power_with_dipm level.
It has not been tested with medium_power, but that typically has no
measurable power-savings.
Note the reporters Crucial_CT480M500SSD3 has a firmware version of MU03
and there is a MU05 update available, but that update does not mention any
LPM fixes in its changelog, so the quirk matches all firmware versions.
In my experience the LPM problems with (older) Crucial SSDs seem to be
limited to higher capacity versions of the SSDs (different firmware?),
so this commit adds a NOLPM quirk for the 480 and 960GB versions of the
M500, to avoid LPM causing issues with these SSDs.
Cc: stable@vger.kernel.org
Reported-and-tested-by: Martin Steigerwald <martin@lichtvoll.de>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Samsung explicitly states that queued TRIM is supported for Linux with
860 PRO and 860 EVO.
Make the previous blacklist to cover only 840 and 850 series.
Signed-off-by: Park Ju Hyung <qkrwngud825@gmail.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
Like the Highpoint Rocketraid 642L and cards using a Marvel 88SE9235
controller in general, this RAID card also supports AHCI mode and short
of a custom driver, this is the only way to make it work under Linux.
Note that even though the card is called to 644L, it has a product-id
of 0x0645.
Cc: stable@vger.kernel.org
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1534106
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
We've got a kernel panic when using sata disk with sas controller:
[115946.152283] Unable to handle kernel NULL pointer dereference at virtual address 000007d8
[115946.223963] CPU: 0 PID: 22175 Comm: kworker/0:1 Tainted: G W OEL 4.14.0 #1
[115946.232925] Workqueue: events ata_scsi_hotplug
[115946.237938] task: ffff8021ee50b180 task.stack: ffff00000d5d0000
[115946.244717] PC is at sas_find_dev_by_rphy+0x44/0x114
[115946.250224] LR is at sas_find_dev_by_rphy+0x3c/0x114
......
[115946.355701] Process kworker/0:1 (pid: 22175, stack limit = 0xffff00000d5d0000)
[115946.363369] Call trace:
[115946.456356] [<ffff000008878a9c>] sas_find_dev_by_rphy+0x44/0x114
[115946.462908] [<ffff000008878b8c>] sas_target_alloc+0x20/0x5c
[115946.469408] [<ffff00000885a31c>] scsi_alloc_target+0x250/0x308
[115946.475781] [<ffff00000885ba30>] __scsi_add_device+0xb0/0x154
[115946.481991] [<ffff0000088b520c>] ata_scsi_scan_host+0x180/0x218
[115946.488367] [<ffff0000088b53d8>] ata_scsi_hotplug+0xb0/0xcc
[115946.494801] [<ffff0000080ebd70>] process_one_work+0x144/0x390
[115946.501115] [<ffff0000080ec100>] worker_thread+0x144/0x418
[115946.507093] [<ffff0000080f2c98>] kthread+0x10c/0x138
[115946.512792] [<ffff0000080855dc>] ret_from_fork+0x10/0x18
We found that Ding Xiang has reported a similar bug before:
https://patchwork.kernel.org/patch/9179817/
And this bug still exists in mainline. Since libsas handles hotplug and
device adding/removing itself, do not need to schedule ata hot plug task
here if it is a sas host.
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Cc: Ding Xiang <dingxiang@huawei.com>
Cc: stable@vger.kernel.org
Signed-off-by: Tejun Heo <tj@kernel.org>
After Laptop Mode Tools starts to use min_power for LPM, a user found
out Crucial BX100 SSD can't get mounted.
Crucial BX100 SSD 500GB drive don't work well with min_power. This also
happens to med_power_with_dipm.
So let's disable LPM for Crucial BX100 SSD 500GB drive.
BugLink: https://bugs.launchpad.net/bugs/1726930
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
Various people have reported the Crucial MX100 512GB model not working
with LPM set to min_power. I've now received a report that it also does
not work with the new med_power_with_dipm level.
It does work with medium_power, but that has no measurable power-savings
and given the amount of people being bitten by the other levels not
working, this commit just disables LPM altogether.
Note all reporters of this have either the 512GB model (max capacity), or
are not specifying their SSD's size. So for now this quirk assumes this is
a problem with the 512GB model only.
Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=89261
Buglink: https://github.com/linrunner/TLP/issues/84
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Because power of Salvator-X board is cut off in suspend,
it needs to reset SATA PHY state in resume.
Otherwise, SATA partition could not be accessed anymore.
Signed-off-by: Khiem Nguyen <khiem.nguyen.xt@rvc.renesas.com>
Signed-off-by: Hien Dang <hien.dang.eb@rvc.renesas.com>
[reinit phy in sata_rcar_resume() function on R-Car Gen3 only]
[factor out SATA module init sequence]
[fixed the prefix for the subject]
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
syzkaller hit a WARN() in ata_bmdma_qc_issue() when writing to /dev/sg0.
This happened because it issued an ATA pass-through command (ATA_16)
where the protocol field indicated that NCQ should be used -- but the
device did not support NCQ.
We could just remove the WARN() from libata-sff.c, but the real problem
seems to be that the SCSI -> ATA translation code passes through NCQ
commands without verifying that the device actually supports NCQ.
Fix this by adding the appropriate check to ata_scsi_pass_thru().
Here's reproducer that works in QEMU when /dev/sg0 refers to a disk of
the default type ("82371SB PIIX3 IDE"):
#include <fcntl.h>
#include <unistd.h>
int main()
{
char buf[53] = { 0 };
buf[36] = 0x85; /* ATA_16 */
buf[37] = (12 << 1); /* FPDMA */
buf[38] = 0x1; /* Has data */
buf[51] = 0xC8; /* ATA_CMD_READ */
write(open("/dev/sg0", O_RDWR), buf, sizeof(buf));
}
Fixes: ee7fb331c3 ("libata: add support for NCQ commands for SG interface")
Reported-by: syzbot+2f69ca28df61bdfc77cd36af2e789850355a221e@syzkaller.appspotmail.com
Cc: <stable@vger.kernel.org> # v4.4+
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
syzkaller hit a WARN() in ata_qc_issue() when writing to /dev/sg0. This
happened because it issued a READ_6 command with no data buffer.
Just remove the WARN(), as it doesn't appear indicate a kernel bug. The
expected behavior is to fail the command, which the code does.
Here's a reproducer that works in QEMU when /dev/sg0 refers to a disk of
the default type ("82371SB PIIX3 IDE"):
#include <fcntl.h>
#include <unistd.h>
int main()
{
char buf[42] = { [36] = 0x8 /* READ_6 */ };
write(open("/dev/sg0", O_RDWR), buf, sizeof(buf));
}
Fixes: f92a26365a ("libata: change ATA_QCFLAG_DMAMAP semantics")
Reported-by: syzbot+f7b556d1766502a69d85071d2ff08bd87be53d0f@syzkaller.appspotmail.com
Cc: <stable@vger.kernel.org> # v2.6.25+
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
syzkaller reported a crash in ata_bmdma_fill_sg() when writing to
/dev/sg1. The immediate cause was that the ATA command's scatterlist
was not DMA-mapped, which causes 'pi - 1' to underflow, resulting in a
write to 'qc->ap->bmdma_prd[0xffffffff]'.
Strangely though, the flag ATA_QCFLAG_DMAMAP was set in qc->flags. The
root cause is that when __ata_scsi_queuecmd() is preparing to relay a
SCSI command to an ATAPI device, it doesn't correctly validate the CDB
length before copying it into the 16-byte buffer 'cdb' in 'struct
ata_queued_cmd'. Namely, it validates the fixed CDB length expected
based on the SCSI opcode but not the actual CDB length, which can be
larger due to the use of the SG_NEXT_CMD_LEN ioctl. Since 'flags' is
the next member in ata_queued_cmd, a buffer overflow corrupts it.
Fix it by requiring that the actual CDB length be <= 16 (ATAPI_CDB_LEN).
[Really it seems the length should be required to be <= dev->cdb_len,
but the current behavior seems to have been intentionally introduced by
commit 607126c2a2 ("libata-scsi: be tolerant of 12-byte ATAPI commands
in 16-byte CDBs") to work around a userspace bug in mplayer. Probably
the workaround is no longer needed (mplayer was fixed in 2007), but
continuing to allow lengths to up 16 appears harmless for now.]
Here's a reproducer that works in QEMU when /dev/sg1 refers to the
CD-ROM drive that qemu-system-x86_64 creates by default:
#include <fcntl.h>
#include <sys/ioctl.h>
#include <unistd.h>
#define SG_NEXT_CMD_LEN 0x2283
int main()
{
char buf[53] = { [36] = 0x7e, [52] = 0x02 };
int fd = open("/dev/sg1", O_RDWR);
ioctl(fd, SG_NEXT_CMD_LEN, &(int){ 17 });
write(fd, buf, sizeof(buf));
}
The crash was:
BUG: unable to handle kernel paging request at ffff8cb97db37ffc
IP: ata_bmdma_fill_sg drivers/ata/libata-sff.c:2623 [inline]
IP: ata_bmdma_qc_prep+0xa4/0xc0 drivers/ata/libata-sff.c:2727
PGD fb6c067 P4D fb6c067 PUD 0
Oops: 0002 [#1] SMP
CPU: 1 PID: 150 Comm: syz_ata_bmdma_q Not tainted 4.15.0-next-20180202 #99
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.11.0-20171110_100015-anatol 04/01/2014
[...]
Call Trace:
ata_qc_issue+0x100/0x1d0 drivers/ata/libata-core.c:5421
ata_scsi_translate+0xc9/0x1a0 drivers/ata/libata-scsi.c:2024
__ata_scsi_queuecmd drivers/ata/libata-scsi.c:4326 [inline]
ata_scsi_queuecmd+0x8c/0x210 drivers/ata/libata-scsi.c:4375
scsi_dispatch_cmd+0xa2/0xe0 drivers/scsi/scsi_lib.c:1727
scsi_request_fn+0x24c/0x530 drivers/scsi/scsi_lib.c:1865
__blk_run_queue_uncond block/blk-core.c:412 [inline]
__blk_run_queue+0x3a/0x60 block/blk-core.c:432
blk_execute_rq_nowait+0x93/0xc0 block/blk-exec.c:78
sg_common_write.isra.7+0x272/0x5a0 drivers/scsi/sg.c:806
sg_write+0x1ef/0x340 drivers/scsi/sg.c:677
__vfs_write+0x31/0x160 fs/read_write.c:480
vfs_write+0xa7/0x160 fs/read_write.c:544
SYSC_write fs/read_write.c:589 [inline]
SyS_write+0x4d/0xc0 fs/read_write.c:581
do_syscall_64+0x5e/0x110 arch/x86/entry/common.c:287
entry_SYSCALL_64_after_hwframe+0x21/0x86
Fixes: 607126c2a2 ("libata-scsi: be tolerant of 12-byte ATAPI commands in 16-byte CDBs")
Reported-by: syzbot+1ff6f9fcc3c35f1c72a95e26528c8e7e3276e4da@syzkaller.appspotmail.com
Cc: <stable@vger.kernel.org> # v2.6.24+
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Indent the numbered item with one space like all other items in the same
list.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Tejun Heo <tj@kernel.org>
Exit directly with ENODEV, if the AHCI controller is not available
anymore. Otherwise a delay of 500ms for each port is added to the remove
function while trying to issue a command on the non-existent controller.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
This fixs the following comile warnings with ATA_DEBUG enabled,
which detected by Linaro GCC 5.2-2015.11:
drivers/ata/libata-scsi.c: In function 'ata_scsi_dump_cdb':
./include/linux/kern_levels.h:5:18: warning: format '%d' expects
argument of type 'int', but argument 6 has type 'u64 {aka long
long unsigned int}' [-Wformat=]
tj: Patch hand-applied and description trimmed.
Signed-off-by: Dong Bo <dongbo4@huawei.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ttq9
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.16-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- skip AER driver error recovery callbacks for correctable errors
reported via ACPI APEI, as we already do for errors reported via the
native path (Tyler Baicar)
- fix DPC shared interrupt handling (Alex Williamson)
- print full DPC interrupt number (Keith Busch)
- enable DPC only if AER is available (Keith Busch)
- simplify DPC code (Bjorn Helgaas)
- calculate ASPM L1 substate parameter instead of hardcoding it (Bjorn
Helgaas)
- enable Latency Tolerance Reporting for ASPM L1 substates (Bjorn
Helgaas)
- move ASPM internal interfaces out of public header (Bjorn Helgaas)
- allow hot-removal of VGA devices (Mika Westerberg)
- speed up unplug and shutdown by assuming Thunderbolt controllers
don't support Command Completed events (Lukas Wunner)
- add AtomicOps support for GPU and Infiniband drivers (Felix Kuehling,
Jay Cornwall)
- expose "ari_enabled" in sysfs to help NIC naming (Stuart Hayes)
- clean up PCI DMA interface usage (Christoph Hellwig)
- remove PCI pool API (replaced with DMA pool) (Romain Perier)
- deprecate pci_get_bus_and_slot(), which assumed PCI domain 0 (Sinan
Kaya)
- move DT PCI code from drivers/of/ to drivers/pci/ (Rob Herring)
- add PCI-specific wrappers for dev_info(), etc (Frederick Lawler)
- remove warnings on sysfs mmap failure (Bjorn Helgaas)
- quiet ROM validation messages (Alex Deucher)
- remove redundant memory alloc failure messages (Markus Elfring)
- fill in types for compile-time VGA and other I/O port resources
(Bjorn Helgaas)
- make "pci=pcie_scan_all" work for Root Ports as well as Downstream
Ports to help AmigaOne X1000 (Bjorn Helgaas)
- add SPDX tags to all PCI files (Bjorn Helgaas)
- quirk Marvell 9128 DMA aliases (Alex Williamson)
- quirk broken INTx disable on Ceton InfiniTV4 (Bjorn Helgaas)
- fix CONFIG_PCI=n build by adding dummy pci_irqd_intx_xlate() (Niklas
Cassel)
- use DMA API to get MSI address for DesignWare IP (Niklas Cassel)
- fix endpoint-mode DMA mask configuration (Kishon Vijay Abraham I)
- fix ARTPEC-6 incorrect IS_ERR() usage (Wei Yongjun)
- add support for ARTPEC-7 SoC (Niklas Cassel)
- add endpoint-mode support for ARTPEC (Niklas Cassel)
- add Cadence PCIe host and endpoint controller driver (Cyrille
Pitchen)
- handle multiple INTx status bits being set in dra7xx (Vignesh R)
- translate dra7xx hwirq range to fix INTD handling (Vignesh R)
- remove deprecated Exynos PHY initialization code (Jaehoon Chung)
- fix MSI erratum workaround for HiSilicon Hip06/Hip07 (Dongdong Liu)
- fix NULL pointer dereference in iProc BCMA driver (Ray Jui)
- fix Keystone interrupt-controller-node lookup (Johan Hovold)
- constify qcom driver structures (Julia Lawall)
- rework Tegra config space mapping to increase space available for
endpoints (Vidya Sagar)
- simplify Tegra driver by using bus->sysdata (Manikanta Maddireddy)
- remove PCI_REASSIGN_ALL_BUS usage on Tegra (Manikanta Maddireddy)
- add support for Global Fabric Manager Server (GFMS) event to
Microsemi Switchtec switch driver (Logan Gunthorpe)
- add IDs for Switchtec PSX 24xG3 and PSX 48xG3 (Kelvin Cao)
* tag 'pci-v4.16-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (140 commits)
PCI: cadence: Add EndPoint Controller driver for Cadence PCIe controller
dt-bindings: PCI: cadence: Add DT bindings for Cadence PCIe endpoint controller
PCI: endpoint: Fix EPF device name to support multi-function devices
PCI: endpoint: Add the function number as argument to EPC ops
PCI: cadence: Add host driver for Cadence PCIe controller
dt-bindings: PCI: cadence: Add DT bindings for Cadence PCIe host controller
PCI: Add vendor ID for Cadence
PCI: Add generic function to probe PCI host controllers
PCI: generic: fix missing call of pci_free_resource_list()
PCI: OF: Add generic function to parse and allocate PCI resources
PCI: Regroup all PCI related entries into drivers/pci/Makefile
PCI/DPC: Reformat DPC register definitions
PCI/DPC: Add and use DPC Status register field definitions
PCI/DPC: Squash dpc_rp_pio_get_info() into dpc_process_rp_pio_error()
PCI/DPC: Remove unnecessary RP PIO register structs
PCI/DPC: Push dpc->rp_pio_status assignment into dpc_rp_pio_get_info()
PCI/DPC: Squash dpc_rp_pio_print_error() into dpc_rp_pio_get_info()
PCI/DPC: Make RP PIO log size check more generic
PCI/DPC: Rename local "status" to "dpc_status"
PCI/DPC: Squash dpc_rp_pio_print_tlp_header() into dpc_rp_pio_print_error()
...
Pull libata updates from Tejun Heo:
"Nothing too interesting. Several patches to convert mdelay() to
usleep_range(), removal of unused pata_at32, and other low level
driver specific changes"
* 'for-4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ata: pata_pdc2027x: Replace mdelay with msleep
ata: pata_it821x: Replace mdelay with usleep_range in it821x_firmware_command
ata: sata_mv: Replace mdelay with usleep_range in mv_reset_channel
ata: remove pata_at32
phy: brcm-sata: remove unused variable
phy: brcm-sata: fix semicolon.cocci warnings
ata: ahci_brcm: Recover from failures to identify devices
phy: brcm-sata: Implement calibrate callback
ahci: Add Intel Cannon Lake PCH-H PCI ID
ata_piix: constify pci_bits
libata:pata_atiixp: Don't use unconnected secondary port on SB600
ata: ahci_brcm: Avoid clobbering SATA_TOP_CTRL_BUS_CTRL
ahci: Allow setting a default LPM policy for mobile chipsets
ahci: Add PCI ids for Intel Bay Trail, Cherry Trail and Apollo Lake AHCI
ahci: Annotate PCI ids for mobile Intel chipsets as such
After checking all possible call chains to pdc_adjust_pll and
pdc_detect_pll_input_clock,
my tool finds that these functions are never called in atomic context,
namely never in an interrupt handler or holding a spinlock.
And their caller functions pdc2027x_init_one and pdc2027x_reinit_one
calls pci_enable_device which can sleep, and no spinlock is held when
calling pdc_adjust_pll and pdc_detect_pll_input_clock,
so it proves that pdc_adjust_pll and pdc_detect_pll_input_clock
can call functions which can sleep.
Thus mdelay can be replaced with msleep to avoid busy wait.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
After checking all possible call chains to it821x_firmware_command here,
my tool finds that it821x_firmware_command
is never called in atomic context,
namely never in an interrupt handler or holding a spinlock.
And it821x_firmware_command calls kmalloc(GFP_KERNEL),
so it proves again that it821x_firmware_command
can call functions which can sleep.
Thus mdelay can be replaced with usleep_range to avoid busy wait.
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
After checking all possible call chains to mv_reset_channel here,
my tool finds that mv_reset_channel is never called in atomic context,
namely never in an interrupt handler or holding a spinlock.
Thus mdelay can be replaced with usleep_range to avoid busy wait.
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Since AVR32 was removed, pata_at32 is unselectable/uncompilable.
Remove this driver.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
When powering up, the SATA controller may fail to mount the HDD. The SATA
controller will lock up, preventing it from negotiating to a lower speed or
transmitting data. Root cause is power supply noise creating resonance at 6 Ghz
and 3 GHz frequencies, which causes instability in the Clock-Data Recovery
(CDR) frontend module, resulting in false acquisition of the clock at SATA
6G/3G speeds.
The SATA controller may fail to mount the HDD and lock up, requiring a power
cycle. Broadcom chips suspected of being susceptible to this issue include
BCM7445, BCM7439, and BCM7366.
The Kernel implements an error recovery mechanism that resets the SATA PHY and
digital controller when the controller locks up. During this error recovery
process, typically there is less activity on the board and Broadcom STB chip,
so that the power supply is less noisy, thus allowing the SATA controller to
lock correctly.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
pci_get_bus_and_slot() is restrictive such that it assumes domain=0 as
where a PCI device is present. This restricts the device drivers to be
reused for other domain numbers.
Getting ready to remove pci_get_bus_and_slot() function in favor of
pci_get_domain_bus_and_slot().
Use pci_get_domain_bus_and_slot() and extract the actual domain number
from the pdev passed in.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
Acked-by: Tejun Heo <tj@kernel.org>
Add Intel Cannon Lake PCH-H PCI ID to the list of supported controllers.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
pci_bits are not supposed to change at runtime. Functions
pci_test_config_bits() working with const 'struct pci_bits'.
So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The AMD SB600 southbridge has an PATA IDE interface, but the
secondary port has no physical connections, so is disabled in
the PCI header which makes it appear as a legacy port.
On most systems this causes no trouble, but the Amigaone X1000 has
an SB600 connected to a PowerPC SoC PCI-e root port, with an
emulated ISA bus. On this system a kernel panic occurs at boot
time during device attach for the secondary port.
Mark the port as 'dummy' to prevent this. As a bonus, disabling
this will slightly speed up booting on PC systems using an
SB600 as they will now skip 2 known empty ports.
Signed-off-by: Darren Stevens <Darren@stevens-zone.net>
Signed-off-by: Tejun Heo <tj@kernel.org>
We are doing a blind write to SATA_TOP_CTRL_BUS_CTRL to set the system
endian, but in doing so, we are also overwriting other bits, such as the
SATA_SCB_BURST_SIZE and SATA_FIFO_SIZE bits, which impact performance.
Do a read/modify/write so we keep the default values.
While we are at it, we also greatly simplify the logic and just leave
the NSP specific bit settings, instead of having a completely different
sequence.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
LITEON EP1 has the same timeout issues as CX1 series devices.
Revert max_sectors to the value of 1024.
'e0edc8c54646 ("libata: apply MAX_SEC_1024 to all CX1-JB*-HP devices")'
Signed-off-by: Xinyu Lin <xinyu0123@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
On many laptops setting a different LPM policy then unknown /
max_performance can lead to power-savings of 1.0 - 1.5 Watts (when idle).
Modern ultrabooks idle around 6W (at 50% screen brightness), 1.0 - 1.5W
is a significant chunk of this.
There are some performance / latency costs to enabling LPM by default,
so it is desirable to make it possible to set a different LPM policy
for mobile / laptop variants of chipsets / "South Bridges" vs their
desktop / server counterparts. Also enabling LPM by default is not
entirely without risk of regressions. At least min_power is known to
cause issues with some disks, including some reports of data corruption.
This commits adds a new ahci.mobile_lpm_policy kernel cmdline option,
which defaults to a new SATA_MOBILE_LPM_POLICY Kconfig option so that
Linux distributions can choose to set a LPM policy for mobile chipsets
by default.
The reason to have both a kernel cmdline option and a Kconfig default
value for it, is to allow easy overriding of the default to allow
trouble-shooting without needing to rebuild the kernel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Add PCI ids for Intel Bay Trail, Cherry Trail and Apollo Lake AHCI
SATA controllers. This commit is a preparation patch for allowing a
different default sata link powermanagement policy for mobile chipsets.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Intel uses different SATA PCI ids for the Desktop and Mobile SKUs of their
chipsets. For older models the comment describing which chipset the PCI id
is for, aksi indicates when we're dealing with a mobile SKU. Extend the
comments for recent chipsets to also indicate mobile SKUs.
The information this commit adds comes from Intel's chipset datasheets.
This commit is a preparation patch for allowing a different default
sata link powermanagement policy for mobile chipsets.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
During hotplug, it is possible for 6Gbps link speed to be limited all
the way down to 1.5 Gbps which may lead to a slower link speed when
drive is re-connected.
This behavior has been seen on a Intel Lewisburg SATA controller
(8086:a1d2) with HGST HUH728080ALE600 drive where SATA link speed was
limited to 1.5 Gbps and when re-connected the link came up 3.0 Gbps.
This patch was retested on above configuration and showed the
hotplugged link to come back online at max speed (6Gbps). I did not
see the downgrade when testing on Intel C600/X79, but retested patched
linux-4.14-rc5 kernel and didn't see any side effects from this
change. Also, successfully retested hotplug on port multiplier 3Gbps
link.
tj: Minor comment updates.
Signed-off-by: David Milburn <dmilburn@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The driver name "ahci" is already used by the ahci platform driver.
This leads to the following error:
Error: Driver 'ahci' is already registered, aborting...
Change the name to ahci-mtk to fix this.
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
These PP2C and PP3C registers control the configuration of the PHY
control OOB timing for the COMINIT/COMWAKE parameters respectively
for sata port. Overwrite default values with calculated ones to get
better OOB timing.
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Make these pdc2027x_*_timing structures const as it is never modified.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Here, The function pdc_hardware_init always return zero. So it is not
necessary to check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Pull libata updates from Tejun Heo:
"Nothing too interesting or alarming. Other than a new power saving
mode addition to ahci and crash fix on a tracepoint, all changes are
trivial or device-specific"
* 'for-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata: (22 commits)
ahci: imx: Handle increased read failures for IMX53 temperature sensor in low frequency mode.
ata: sata_dwc_460ex: Propagate platform device ID to DMA driver
ata: fixes kernel crash while tracing ata_eh_link_autopsy event
ata: pata_pdc2027x: Fix space before '[' error.
libata: fix spelling mistake: 'ambigious' -> 'ambiguous'
ata: ceva: Add SMMU support for SATA IP
ata: ceva: Correct the suspend and resume logic for SATA
ata: ceva: Correct the AXI bus configuration for SATA ports
ata: ceva: Add CCI support for SATA if CCI is enabled
ata: ceva: Make RxWaterMark value as module parameter
ata: ceva: Disable Device Sleep capability
ata: ceva: Add gen 3 mode support in driver
ata: ceva: Move sata port phy oob settings to device-tree
devicetree: bindings: Add sata port phy config parameters in ahci-ceva
ata: mark expected switch fall-throughs
ata: sata_mv: remove a redundant assignment to pointer ehi
ahci: Add support for Cavium's fifth generation SATA controller
ata: sata_rcar: Use of_device_get_match_data() helper
libata: make ata_port_type const
libata: make static arrays const, reduces object code size
...
Pull timer updates from Thomas Gleixner:
"Yet another big pile of changes:
- More year 2038 work from Arnd slowly reaching the point where we
need to think about the syscalls themself.
- A new timer function which allows to conditionally (re)arm a timer
only when it's either not running or the new expiry time is sooner
than the armed expiry time. This allows to use a single timer for
multiple timeout requirements w/o caring about the first expiry
time at the call site.
- A new NMI safe accessor to clock real time for the printk timestamp
work. Can be used by tracing, perf as well if required.
- A large number of timer setup conversions from Kees which got
collected here because either maintainers requested so or they
simply got ignored. As Kees pointed out already there are a few
trivial merge conflicts and some redundant commits which was
unavoidable due to the size of this conversion effort.
- Avoid a redundant iteration in the timer wheel softirq processing.
- Provide a mechanism to treat RTC implementations depending on their
hardware properties, i.e. don't inflict the write at the 0.5
seconds boundary which originates from the PC CMOS RTC to all RTCs.
No functional change as drivers need to be updated separately.
- The usual small updates to core code clocksource drivers. Nothing
really exciting"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (111 commits)
timers: Add a function to start/reduce a timer
pstore: Use ktime_get_real_fast_ns() instead of __getnstimeofday()
timer: Prepare to change all DEFINE_TIMER() callbacks
netfilter: ipvs: Convert timers to use timer_setup()
scsi: qla2xxx: Convert timers to use timer_setup()
block/aoe: discover_timer: Convert timers to use timer_setup()
ide: Convert timers to use timer_setup()
drbd: Convert timers to use timer_setup()
mailbox: Convert timers to use timer_setup()
crypto: Convert timers to use timer_setup()
drivers/pcmcia: omap1: Fix error in automated timer conversion
ARM: footbridge: Fix typo in timer conversion
drivers/sgi-xp: Convert timers to use timer_setup()
drivers/pcmcia: Convert timers to use timer_setup()
drivers/memstick: Convert timers to use timer_setup()
drivers/macintosh: Convert timers to use timer_setup()
hwrng/xgene-rng: Convert timers to use timer_setup()
auxdisplay: Convert timers to use timer_setup()
sparc/led: Convert timers to use timer_setup()
mips: ip22/32: Convert timers to use timer_setup()
...
Extended testing has shown that the imx ahci driver sometimes requires
more than the 100 attempts currently alotted in the driver to perform a
successful temperature reading when running at minimum (throttled) CPU
frequency.
Debugging suggests that the read cycle can take 160 attempts (which given
that the driver averages 80 readings from the ADC equates to one failure
on each read).
Increase the attempt limit to 200 in order to greatly reduce the
likelihood of the driver failing to perform a temperature reading,
especially at low CPU frequency.
Signed-off-by: Egor Starkov <egor.starkov@ge.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: Tejun Heo <tj@kernel.org>
Propagate platform device ID to DMA driver to distinguish relationship
between DMA and SATA instances.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
When tracing ata link error event, the kernel crashes when the disk is
removed due to NULL pointer access by trace_ata_eh_link_autopsy API.
This occurs as the dev is NULL when the disk disappeared. This patch
fixes this crash by calling trace_ata_eh_link_autopsy only if "dev"
is not NULL.
v2 changes:
Removed direct passing "link" pointer instead of "dev" in trace API.
Signed-off-by: Rameshwar Prasad Sahu <rsahu@apm.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Fixes: 255c03d15a ("libata: Add tracepoints")
Cc: stable@vger.kernel.org # v4.1+
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
AXI master interface in CEVA AHCI controller requires two unique
Write/Read ID tags per port. This is because, ahci controller uses
different AXI ID[3:0] bits for identifying non-data transfers(like
reading descriptors, updating PRD tables, etc) and data transfers
(like sending/receiving FIS).To make SMMU work with SATA we need to
add correct SMMU stream id for SATA. SMMU stream id for SATA is
determined based on the AXI ID[1:0] as shown below
SATA SMMU ID = <TBU number>, 0011, 00, 00, AXI ID[1:0]
Note: SATA in ZynqMp uses TBU1 so TBU number = 0x1, so
SMMU ID = 001, 0011, 00, 00, AXI ID[1:0]
Since we have four different AXI ID[3:0] (2 for port0 & 2 for port1
as said above) we get four different SMMU stream id's combinations
for SATA. These AXI ID can be configured using PAXIC register.
In this patch we assumed the below AXI ID values
Read ID/ Write ID for Non-Data Port0 transfers = 0
Read ID/ Write ID for Data Port0 transfers = 1
Read ID/ Write ID for Non-Data Port1 transfers = 2
Read ID/ Write ID for Data Port1 transfers = 3
Based on the above values,SMMU stream ID's for SATA will be 0x4c0 &
0x4c1 for PORT0, 0x4c2 & 0x4c3 for PORT1. These values needed to be
added to iommus dts property. This patch does the same.
Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The present suspend code disables the port interrupts
and stops the HBA. On resume it enables the interrupts and HBA.
This works fine until the FPD power domain is not off.
If FPD is off then the ceva vendor specific configurations like
OOB, AXI settings are lost, they need to be re-programmed and
also since SERDES is also in FPD , SATA lane phy init needs to
be called again (which is not happening in the present sequence)
Because of this incorrect sequence SATA fails to work on resume.
This patch corrects the code to make Suspend & Resume work in normal
and FPD off cases.
Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Reviewed-by: Shubhrajyoti Datta <shubhraj@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Previously PAXIC register was programmed before configuring PCFG
register. PCFG should be programmed with the address of the port
for which PAXIC should be configured for.
This was not happening before, so only one port PAXIC was written
correctly and the other port was having wrong value.
This patch moves the PXAIC register write after configuring PCFG,
doing so will correct the axi bus settings for sata port0 & port1.
Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This patch adds support for CCI in SATA controller if CCI is
enabled in design. This patch will add CCI settings for SATA
if "dma-coherent" dts property is added.
Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
