- Mark ATS on AMD Stoney Radeon R7 GPU broken to avoid IOMMU issues
(Nikolai Kostrigin)
- Mark Atheros AR9462 to avoid bus reset that locks up host machine
(James Prestwood)
* pci/virtualization:
PCI: Mark Atheros AR9462 to avoid bus reset
PCI: Mark AMD Stoney Radeon R7 GPU ATS as broken
- Add a whitelist of Root Complexes known to support peer-to-peer DMA
between Root Ports (Christian König)
* pci/peer-to-peer:
PCI/P2PDMA: Allow P2P DMA between any devices under AMD ZEN Root Complex
- Fix RPA and RPA DLPAR refcount issues (Tyrel Datwyler)
- Stop exporting pci_get_hp_params() (Alexandru Gagniuc)
- Simplify _HPP, _HPX parsing (Alexandru Gagniuc)
- Add support for _HPX Type 3 settings (Alexandru Gagniuc)
- Tell firmware we support _HPX Type 3 via _OSC (Alexandru Gagniuc)
* pci/hotplug:
PCI/ACPI: Advertise _HPX Type 3 support via _OSC
PCI/ACPI: Implement _HPX Type 3 Setting Record
PCI/ACPI: Remove the need for 'struct hotplug_params'
PCI/ACPI: Do not export pci_get_hp_params()
PCI: rpaphp: Get/put device node reference during slot alloc/dealloc
PCI: rpadlpar: Fix leaked device_node references in add/remove paths
- Enable PCIe services for host controller drivers that use managed host
bridge alloc (Jean-Philippe Brucker)
- Add quirk to clear PCIe Retrain Link bit to work around Pericom bridge
erratum (Stefan Mätje)
- Add "external-facing" DT property to identify cases where we require
IOMMU protection from untrusted devices (Jean-Philippe Brucker)
- Support fixed bus numbers from bridge Enhanced Allocation capabilities
(Subbaraya Sundeep)
* pci/enumeration:
PCI: Assign bus numbers present in EA capability for bridges
PCI: OF: Support "external-facing" property
dt-bindings: Add "external-facing" PCIe port property
PCI: Rework pcie_retrain_link() wait loop
PCI: Work around Pericom PCIe-to-PCI bridge Retrain Link erratum
PCI: Factor out pcie_retrain_link() function
PCI: Init PCIe feature bits for managed host bridge alloc
The PCI specs say that peer-to-peer DMA should be supported between any two
devices that have a common upstream PCI-to-PCI bridge. But devices under
different Root Ports don't share a common upstream bridge, and PCIe r4.0,
sec 1.3.1, says routing peer-to-peer transactions between Root Ports in the
same Root Complex is optional.
Many Root Complexes, including AMD ZEN, *do* support peer-to-peer DMA even
between Root Ports. Add a whitelist and allow peer-to-peer DMA if both
participants are attached to a Root Complex known to support it.
Link: https://lore.kernel.org/linux-pci/20190418115859.2394-1-christian.koenig@amd.com
Signed-off-by: Christian König <christian.koenig@amd.com>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
In several places in the kernel we find PCI_DEVID used like this:
PCI_DEVID(dev->bus->number, dev->devfn)
Add a "pci_dev_id(struct pci_dev *dev)" helper to simplify callers.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
On ThinkPad P50 SKUs with an Nvidia Quadro M1000M instead of the M2000M
variant, the BIOS does not always reset the secondary Nvidia GPU during
reboot if the laptop is configured in Hybrid Graphics mode. The reason is
unknown, but the following steps and possibly a good bit of patience will
reproduce the issue:
1. Boot up the laptop normally in Hybrid Graphics mode
2. Make sure nouveau is loaded and that the GPU is awake
3. Allow the Nvidia GPU to runtime suspend itself after being idle
4. Reboot the machine, the more sudden the better (e.g. sysrq-b may help)
5. If nouveau loads up properly, reboot the machine again and go back to
step 2 until you reproduce the issue
This results in some very strange behavior: the GPU will be left in exactly
the same state it was in when the previously booted kernel started the
reboot. This has all sorts of bad side effects: for starters, this
completely breaks nouveau starting with a mysterious EVO channel failure
that happens well before we've actually used the EVO channel for anything:
nouveau 0000:01:00.0: disp: chid 0 mthd 0000 data 00000400 00001000 00000002
This causes a timeout trying to bring up the GR ctx:
nouveau 0000:01:00.0: timeout
WARNING: CPU: 0 PID: 12 at drivers/gpu/drm/nouveau/nvkm/engine/gr/ctxgf100.c:1547 gf100_grctx_generate+0x7b2/0x850 [nouveau]
Hardware name: LENOVO 20EQS64N0B/20EQS64N0B, BIOS N1EET82W (1.55 ) 12/18/2018
Workqueue: events_long drm_dp_mst_link_probe_work [drm_kms_helper]
...
nouveau 0000:01:00.0: gr: wait for idle timeout (en: 1, ctxsw: 0, busy: 1)
nouveau 0000:01:00.0: gr: wait for idle timeout (en: 1, ctxsw: 0, busy: 1)
nouveau 0000:01:00.0: fifo: fault 01 [WRITE] at 0000000000008000 engine 00 [GR] client 15 [HUB/SCC_NB] reason c4 [] on channel -1 [0000000000 unknown]
The GPU never manages to recover. Booting without loading nouveau causes
issues as well, since the GPU starts sending spurious interrupts that cause
other device's IRQs to get disabled by the kernel:
irq 16: nobody cared (try booting with the "irqpoll" option)
...
handlers:
[<000000007faa9e99>] i801_isr [i2c_i801]
Disabling IRQ #16
...
serio: RMI4 PS/2 pass-through port at rmi4-00.fn03
i801_smbus 0000:00:1f.4: Timeout waiting for interrupt!
i801_smbus 0000:00:1f.4: Transaction timeout
rmi4_f03 rmi4-00.fn03: rmi_f03_pt_write: Failed to write to F03 TX register (-110).
i801_smbus 0000:00:1f.4: Timeout waiting for interrupt!
i801_smbus 0000:00:1f.4: Transaction timeout
rmi4_physical rmi4-00: rmi_driver_set_irq_bits: Failed to change enabled interrupts!
This causes the touchpad and sometimes other things to get disabled.
Since this happens without nouveau, we can't fix this problem from nouveau
itself.
Add a PCI quirk for the specific P50 variant of this GPU. Make sure the
GPU is advertising NoReset- so we don't reset the GPU when the machine is
in Dedicated graphics mode (where the GPU being initialized by the BIOS is
normal and expected). Map the GPU MMIO space and read the magic 0x2240c
register, which will have bit 1 set if the device was POSTed during a
previous boot. Once we've confirmed all of this, reset the GPU and
re-disable it - bringing it back to a healthy state.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=203003
Link: https://lore.kernel.org/lkml/20190212220230.1568-1-lyude@redhat.com
Signed-off-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: nouveau@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Cc: Karol Herbst <kherbst@redhat.com>
Cc: Ben Skeggs <skeggsb@gmail.com>
Cc: stable@vger.kernel.org
The _HPX Type 3 Setting Record is intended to be more generic and allow
configuration of settings not possible with Type 2 records. For example,
firmware could ensure that the completion timeout value is set accordingly
throughout the PCI tree.
Implement support for _HPX Type 3 Setting Records, which were added in the
ACPI 6.3 spec.
Link: https://lore.kernel.org/lkml/20190208162414.3996-4-mr.nuke.me@gmail.com
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
We used to first parse all the _HPP and _HPX tables before using the
information to program registers of PCIe devices. Up through HPX Type 2,
there was only one structure of each type, so we could cheat and store it
on the stack.
With HPX Type 3 we get an arbitrary number of entries, so the above model
doesn't scale that well. Instead of parsing all tables at once, parse and
program each entry separately. For _HPP and _HPX Types 0 through 2, this
is functionally equivalent. The change enables the upcoming _HPX Type 3 to
integrate more easily.
Link: https://lore.kernel.org/lkml/20190208162414.3996-3-mr.nuke.me@gmail.com
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
[bhelgaas: fix build errors]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
pci_get_hp_params() is only used within drivers/pci, and there is no reason
to make it available outside of the PCI core, so stop exporting it.
Link: https://lore.kernel.org/lkml/20190208162414.3996-2-mr.nuke.me@gmail.com
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
When using PCI passthrough with this device, the host machine locks up
completely when starting the VM, requiring a hard reboot. Add a quirk to
avoid bus resets on this device.
Fixes: c3e59ee4e7 ("PCI: Mark Atheros AR93xx to avoid bus reset")
Link: https://lore.kernel.org/linux-pci/20190107213248.3034-1-james.prestwood@linux.intel.com
Signed-off-by: James Prestwood <james.prestwood@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v3.14+
If the bandwidth notification interrupt is left unmasked when entering
suspend to idle, it triggers immediately bringing the system back to
working state.
To keep that from happening, disable the interrupt when entering system
sleep and enable it again during resume.
Reported-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
When running application tool switchtec-user's `firmware update` and `event
wait` commands concurrently, sometimes the firmware update speed reduced
significantly.
It is because when the MRPC event happened after MRPC event occurrence
check but before the event mask loop reaches its header register in event
ISR, the MRPC event would be masked unintentionally. Since there's no
chance to enable it again except for a module reload, all the following
MRPC execution completion checks time out.
Fix this bug by skipping the mask operation for MRPC event in event ISR,
same as what we already do for LINK event.
Fixes: 52eabba5bc ("switchtec: Add IOCTLs to the Switchtec driver")
Signed-off-by: Wesley Sheng <wesley.sheng@microchip.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
The Switchtec devices supports two PCIe Function Frameworks (PFFs) per
upstream port (one for the port itself and one for the management endoint),
and each PFF may have up to 255 ports. Previously the driver only
supported 48 of those ports, and the SWITCHTEC_IOCTL_EVENT_SUMMARY ioctl
only returned information about those 48.
Increase SWITCHTEC_MAX_PFF_CSR from 48 to 255 so the driver supports all
255 possible ports.
Rename SWITCHTEC_IOCTL_EVENT_SUMMARY and associated struct
switchtec_ioctl_event_summary to SWITCHTEC_IOCTL_EVENT_SUMMARY_LEGACY and
switchtec_ioctl_event_summary_legacy with so existing applications work
unchanged, supporting up to 48 ports.
Add replacement SWITCHTEC_IOCTL_EVENT_SUMMARY and struct
switchtec_ioctl_event_summary that new and recompiled applications support
up to 255 ports.
Signed-off-by: Wesley Sheng <wesley.sheng@microchip.com>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
pci_request_region_exclusive() was introduced with commit e8de1481fd
("resource: allow MMIO exclusivity for device drivers") in 2.6.29 which
was released 2008.
It never had an in tree user since then, so after 11 years later let's
remove it.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The "Enhanced Allocation (EA) for Memory and I/O Resources" ECN, approved
23 October 2014, sec 6.9.1.2, specifies a second DW in the capability for
type 1 (bridge) functions to describe fixed secondary and subordinate bus
numbers. This ECN was included in the PCIe r4.0 spec, but sec 6.9.1.2 was
omitted, presumably by mistake.
Read fixed bus numbers from the EA capability for bridges.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
[bhelgaas: add pci_ea_fixed_busnrs() return value]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Set the "untrusted" attribute to any PCIe port that has an
"external-facing" device tree property. Any device downstream of this port
will inherit the attribute and have only the strictest IOMMU protection.
Signed-off-by: Jean-Philippe Brucker <jean-philippe.brucker@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
ATS is broken on the Radeon R7 GPU (at least for Stoney Ridge based laptop)
and causes IOMMU stalls and system failure. Disable ATS on these devices
to make them usable again with IOMMU enabled.
Thanks to Joerg Roedel <jroedel@suse.de> for help.
[bhelgaas: In the email thread mentioned below, Alex suspects the real
problem is in sbios or iommu, so it may affect only certain systems, and it
may affect other devices in those systems as well. However, per Joerg we
lack the ability to debug further, so this quirk is the best we can do for
now.]
Link: https://bugzilla.kernel.org/show_bug.cgi?id=194521
Link: https://lore.kernel.org/lkml/20190408103725.30426-1-nickel@altlinux.org
Fixes: 9b44b0b09d ("PCI: Mark AMD Stoney GPU ATS as broken")
Signed-off-by: Nikolai Kostrigin <nickel@altlinux.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Joerg Roedel <jroedel@suse.de>
CC: stable@vger.kernel.org
When allocating the slot structure we store a pointer to the associated
device_node. We really should be incrementing the reference count, so add
an of_node_get() during slot alloc and an of_node_put() during slot
dealloc.
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The find_dlpar_node() helper returns a device node with its reference
incremented. Both the add and remove paths use this helper for find the
appropriate node, but fail to release the reference when done.
Annotate the find_dlpar_node() helper with a comment about the incremented
reference count and call of_node_put() on the obtained device_node in the
add and remove paths. Also, fixup a reference leak in the find_vio_slot()
helper where we fail to call of_node_put() on the vdevice node after we
iterate over its children.
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Transform wait code to a "do {} while (time_before())" loop as recommended
by reviewer. No functional change intended.
Signed-off-by: Stefan Mätje <stefan.maetje@esd.eu>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Due to an erratum in some Pericom PCIe-to-PCI bridges in reverse mode
(conventional PCI on primary side, PCIe on downstream side), the Retrain
Link bit needs to be cleared manually to allow the link training to
complete successfully.
If it is not cleared manually, the link training is continuously restarted
and no devices below the PCI-to-PCIe bridge can be accessed. That means
drivers for devices below the bridge will be loaded but won't work and may
even crash because the driver is only reading 0xffff.
See the Pericom Errata Sheet PI7C9X111SLB_errata_rev1.2_102711.pdf for
details. Devices known as affected so far are: PI7C9X110, PI7C9X111SL,
PI7C9X130.
Add a new flag, clear_retrain_link, in struct pci_dev. Quirks for affected
devices set this bit.
Note that pcie_retrain_link() lives in aspm.c because that's currently the
only place we use it, but this erratum is not specific to ASPM, and we may
retrain links for other reasons in the future.
Signed-off-by: Stefan Mätje <stefan.maetje@esd.eu>
[bhelgaas: apply regardless of CONFIG_PCIEASPM]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
CC: stable@vger.kernel.org
Factor out pcie_retrain_link() to use for Pericom Retrain Link quirk. No
functional change intended.
Signed-off-by: Stefan Mätje <stefan.maetje@esd.eu>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
CC: stable@vger.kernel.org
Two functions allocate a host bridge: devm_pci_alloc_host_bridge() and
pci_alloc_host_bridge(). At the moment, only the unmanaged one initializes
the PCIe feature bits, which prevents from using features such as hotplug
or AER on some systems, when booting with device tree. Make the
initialization code common.
Fixes: 02bfeb4842 ("PCI/portdrv: Simplify PCIe feature permission checking")
Signed-off-by: Jean-Philippe Brucker <jean-philippe.brucker@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v4.17+
Change pcie-xilinx-nwl.c to use pci_msi_mask_irq() and pci_msi_unmask_irq()
like all other PCI host controller drivers. Remove the now-unused
mask_msi_irq() and unmask_msi_irq().
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Michal Simek <michal.simek@xilinx.com>
CC: linux-arm-kernel@lists.infradead.org
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
This patch fixes the following warnings:
drivers/pci/proc.c: In function ‘proc_bus_pci_ioctl’:
drivers/pci/proc.c:216:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (arch_can_pci_mmap_wc()) {
^
drivers/pci/proc.c:225:2: note: here
default:
^~~~~~~
drivers/pci/xen-pcifront.c: In function ‘pcifront_backend_changed’:
drivers/pci/xen-pcifront.c:1105:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (xdev->state == XenbusStateClosed)
^
drivers/pci/xen-pcifront.c:1108:2: note: here
case XenbusStateClosing:
^~~~
Notice that, in this particular case, the /* fall through */
comment is placed at the very bottom of the case statement,
which is what GCC is expecting to find.
Warning level 3 was used: -Wimplicit-fallthrough=3
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Including:
- A big cleanup and optimization patch-set for the
Tegra GART driver
- Documentation updates and fixes for the IOMMU-API
- Support for page request in Intel VT-d scalable mode
- Intel VT-d dma_[un]map_resource() support
- Updates to the ATS enabling code for PCI (acked by Bjorn) and
Intel VT-d to align with the latest version of the ATS spec
- Relaxed IRQ source checking in the Intel VT-d driver for some
aliased devices, needed for future devices which send IRQ
messages from more than on request-ID
- IRQ remapping driver for Hyper-V
- Patches to make generic IOVA and IO-Page-Table code usable
outside of the IOMMU code
- Various other small fixes and cleanups
-----BEGIN PGP SIGNATURE-----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=cKsD
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU updates from Joerg Roedel:
- A big cleanup and optimization patch-set for the Tegra GART driver
- Documentation updates and fixes for the IOMMU-API
- Support for page request in Intel VT-d scalable mode
- Intel VT-d dma_[un]map_resource() support
- Updates to the ATS enabling code for PCI (acked by Bjorn) and Intel
VT-d to align with the latest version of the ATS spec
- Relaxed IRQ source checking in the Intel VT-d driver for some aliased
devices, needed for future devices which send IRQ messages from more
than on request-ID
- IRQ remapping driver for Hyper-V
- Patches to make generic IOVA and IO-Page-Table code usable outside of
the IOMMU code
- Various other small fixes and cleanups
* tag 'iommu-updates-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (60 commits)
iommu/vt-d: Get domain ID before clear pasid entry
iommu/vt-d: Fix NULL pointer reference in intel_svm_bind_mm()
iommu/vt-d: Set context field after value initialized
iommu/vt-d: Disable ATS support on untrusted devices
iommu/mediatek: Fix semicolon code style issue
MAINTAINERS: Add Hyper-V IOMMU driver into Hyper-V CORE AND DRIVERS scope
iommu/hyper-v: Add Hyper-V stub IOMMU driver
x86/Hyper-V: Set x2apic destination mode to physical when x2apic is available
PCI/ATS: Add inline to pci_prg_resp_pasid_required()
iommu/vt-d: Check identity map for hot-added devices
iommu: Fix IOMMU debugfs fallout
iommu: Document iommu_ops.is_attach_deferred()
iommu: Document iommu_ops.iotlb_sync_map()
iommu/vt-d: Enable ATS only if the device uses page aligned address.
PCI/ATS: Add pci_ats_page_aligned() interface
iommu/vt-d: Fix PRI/PASID dependency issue.
PCI/ATS: Add pci_prg_resp_pasid_required() interface.
iommu/vt-d: Allow interrupts from the entire bus for aliased devices
iommu/vt-d: Add helper to set an IRTE to verify only the bus number
iommu: Fix flush_tlb_all typo
...
-----BEGIN PGP SIGNATURE-----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=vf9L
-----END PGP SIGNATURE-----
Merge tag 'pci-v5.1-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- Use match_string() instead of reimplementing it (Andy Shevchenko)
- Enable SERR# forwarding for all bridges (Bharat Kumar Gogada)
- Use Latency Tolerance Reporting if already enabled by platform (Bjorn
Helgaas)
- Save/restore LTR info for suspend/resume (Bjorn Helgaas)
- Fix DPC use of uninitialized data (Dongdong Liu)
- Probe bridge window attributes only once at enumeration-time to fix
device accesses during rescan (Bjorn Helgaas)
- Return BAR size (not "size -1 ") from pci_size() to simplify code (Du
Changbin)
- Use config header type (not class code) identify bridges more
reliably (Honghui Zhang)
- Work around Intel Denverton incorrect Trace Hub BAR size reporting
(Alexander Shishkin)
- Reorder pciehp cached state/hardware state updates to avoid missed
interrupts (Mika Westerberg)
- Turn ibmphp semaphores into completions or mutexes (Arnd Bergmann)
- Mark expected switch fall-through (Mathieu Malaterre)
- Use of_node_name_eq() for node name comparisons (Rob Herring)
- Add ACS and pciehp quirks for HXT SD4800 (Shunyong Yang)
- Consolidate Rohm Vendor ID definitions (Andy Shevchenko)
- Use u32 (not __u32) for things not exposed to userspace (Logan
Gunthorpe)
- Fix locking semantics of bus and slot reset interfaces (Alex
Williamson)
- Update PCIEPORTBUS Kconfig help text (Hou Zhiqiang)
- Allow portdrv to claim subtractive decode Ports so PCIe services will
work for them (Honghui Zhang)
- Report PCIe links that become degraded at run-time (Alexandru
Gagniuc)
- Blacklist Gigabyte X299 Root Port power management to fix Thunderbolt
hotplug (Mika Westerberg)
- Revert runtime PM suspend/resume callbacks that broke PME on network
cable plug (Mika Westerberg)
- Disable Data Link State Changed interrupts to prevent wakeup
immediately after suspend (Mika Westerberg)
- Extend altera to support Stratix 10 (Ley Foon Tan)
- Allow building altera driver on ARM64 (Ley Foon Tan)
- Replace Douglas with Tom Joseph as Cadence PCI host/endpoint
maintainer (Lorenzo Pieralisi)
- Add DT support for R-Car RZ/G2E (R8A774C0) (Fabrizio Castro)
- Add dra72x/dra74x/dra76x SoC compatible strings (Kishon Vijay Abraham I)
- Enable x2 mode support for dra72x/dra74x/dra76x SoC (Kishon Vijay
Abraham I)
- Configure dra7xx PHY to PCIe mode (Kishon Vijay Abraham I)
- Simplify dwc (remove unnecessary header includes, name variables
consistently, reduce inverted logic, etc) (Gustavo Pimentel)
- Add i.MX8MQ support (Andrey Smirnov)
- Add message to help debug dwc MSI-X mask bit errors (Gustavo
Pimentel)
- Work around imx7d PCIe PLL erratum (Trent Piepho)
- Don't assert qcom reset GPIO during probe (Bjorn Andersson)
- Skip dwc MSI init if MSIs have been disabled (Lucas Stach)
- Use memcpy_fromio()/memcpy_toio() instead of plain memcpy() in PCI
endpoint framework (Wen Yang)
- Add interface to discover supported endpoint features to replace a
bitfield that wasn't flexible enough (Kishon Vijay Abraham I)
- Implement the new supported-feature interface for designware-plat,
dra7xx, rockchip, cadence (Kishon Vijay Abraham I)
- Fix issues with 64-bit BAR in endpoints (Kishon Vijay Abraham I)
- Add layerscape endpoint mode support (Xiaowei Bao)
- Remove duplicate struct hv_vp_set in favor of struct hv_vpset (Maya
Nakamura)
- Rework hv_irq_unmask() to use cpumask_to_vpset() instead of
open-coded reimplementation (Maya Nakamura)
- Align Hyper-V struct retarget_msi_interrupt arguments (Maya Nakamura)
- Fix mediatek MMIO size computation to enable full size of available
MMIO space (Honghui Zhang)
- Fix mediatek DMA window size computation to allow endpoint DMA access
to full DRAM address range (Honghui Zhang)
- Fix mvebu prefetchable BAR regression caused by common bridge
emulation that assumed all bridges had prefetchable windows (Thomas
Petazzoni)
- Make advk_pci_bridge_emul_ops static (Wei Yongjun)
- Configure MPS settings for VMD root ports (Jon Derrick)
* tag 'pci-v5.1-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (92 commits)
PCI: Update PCIEPORTBUS Kconfig help text
PCI: Fix "try" semantics of bus and slot reset
PCI/LINK: Report degraded links via link bandwidth notification
dt-bindings: PCI: altera: Add altr,pcie-root-port-2.0
PCI: altera: Enable driver on ARM64
PCI: altera: Add Stratix 10 PCIe support
PCI/PME: Fix possible use-after-free on remove
PCI: aardvark: Make symbol 'advk_pci_bridge_emul_ops' static
PCI: dwc: skip MSI init if MSIs have been explicitly disabled
PCI: hv: Refactor hv_irq_unmask() to use cpumask_to_vpset()
PCI: hv: Replace hv_vp_set with hv_vpset
PCI: hv: Add __aligned(8) to struct retarget_msi_interrupt
PCI: mediatek: Enlarge PCIe2AHB window size to support 4GB DRAM
PCI: mediatek: Fix memory mapped IO range size computation
PCI: dwc: Remove superfluous shifting in definitions
PCI: dwc: Make use of GENMASK/FIELD_PREP
PCI: dwc: Make use of BIT() in constant definitions
PCI: dwc: Share code for dw_pcie_rd/wr_other_conf()
PCI: dwc: Make use of IS_ALIGNED()
PCI: imx6: Add code to request/control "pcie_aux" clock for i.MX8MQ
...
Here is the big driver core patchset for 5.1-rc1
More patches than "normal" here this merge window, due to some work in
the driver core by Alexander Duyck to rework the async probe
functionality to work better for a number of devices, and independant
work from Rafael for the device link functionality to make it work
"correctly".
Also in here is:
- lots of BUS_ATTR() removals, the macro is about to go away
- firmware test fixups
- ihex fixups and simplification
- component additions (also includes i915 patches)
- lots of minor coding style fixups and cleanups.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXH+euQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynyTgCfbV8CLums843sBnT8NnWrTMTdTCcAn1K4re0m
ep8g+6oRLxJy414hogxQ
=bLs2
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the big driver core patchset for 5.1-rc1
More patches than "normal" here this merge window, due to some work in
the driver core by Alexander Duyck to rework the async probe
functionality to work better for a number of devices, and independant
work from Rafael for the device link functionality to make it work
"correctly".
Also in here is:
- lots of BUS_ATTR() removals, the macro is about to go away
- firmware test fixups
- ihex fixups and simplification
- component additions (also includes i915 patches)
- lots of minor coding style fixups and cleanups.
All of these have been in linux-next for a while with no reported
issues"
* tag 'driver-core-5.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (65 commits)
driver core: platform: remove misleading err_alloc label
platform: set of_node in platform_device_register_full()
firmware: hardcode the debug message for -ENOENT
driver core: Add missing description of new struct device_link field
driver core: Fix PM-runtime for links added during consumer probe
drivers/component: kerneldoc polish
async: Add cmdline option to specify drivers to be async probed
driver core: Fix possible supplier PM-usage counter imbalance
PM-runtime: Fix __pm_runtime_set_status() race with runtime resume
driver: platform: Support parsing GpioInt 0 in platform_get_irq()
selftests: firmware: fix verify_reqs() return value
Revert "selftests: firmware: remove use of non-standard diff -Z option"
Revert "selftests: firmware: add CONFIG_FW_LOADER_USER_HELPER_FALLBACK to config"
device: Fix comment for driver_data in struct device
kernfs: Allocating memory for kernfs_iattrs with kmem_cache.
sysfs: remove unused include of kernfs-internal.h
driver core: Postpone DMA tear-down until after devres release
driver core: Document limitation related to DL_FLAG_RPM_ACTIVE
PM-runtime: Take suppliers into account in __pm_runtime_set_status()
device.h: Add __cold to dev_<level> logging functions
...
- Fix mvebu prefetchable BAR regression caused by common bridge emulation
that assumed all bridges had prefetchable windows (Thomas Petazzoni)
- Make advk_pci_bridge_emul_ops static (Wei Yongjun)
* remotes/lorenzo/pci/misc:
PCI: aardvark: Make symbol 'advk_pci_bridge_emul_ops' static
PCI: pci-bridge-emul: Extend pci_bridge_emul_init() with flags
PCI: pci-bridge-emul: Create per-bridge copy of register behavior
- Fix mediatek MMIO size computation to enable full size of available
MMIO space (Honghui Zhang)
- Fix mediatek DMA window size computation to allow endpoint DMA access
to full DRAM address range (Honghui Zhang)
* remotes/lorenzo/pci/mediatek:
PCI: mediatek: Enlarge PCIe2AHB window size to support 4GB DRAM
PCI: mediatek: Fix memory mapped IO range size computation
- Use memcpy_fromio()/memcpy_toio() instead of plain memcpy() in PCI
endpoint framework (Wen Yang)
- Add interface to discover supported endpoint features to replace a
bitfield that wasn't flexible enough (Kishon Vijay Abraham I)
- Implement the new supported-feature interface for designware-plat,
dra7xx, rockchip, cadence (Kishon Vijay Abraham I)
- Fix issues with 64-bit BAR in endpoints (Kishon Vijay Abraham I)
- Add layerscape endpoint mode support (Xiaowei Bao)
* remotes/lorenzo/pci/endpoint:
misc: pci_endpoint_test: Add the layerscape EP device support
PCI: layerscape: Add EP mode support
arm64: dts: Add the PCIE EP node in dts
dt-bindings: add DT binding for the layerscape PCIe controller with EP mode
PCI: endpoint: Remove features member in struct pci_epc
PCI: designware-plat: Remove setting epc->features in Designware plat EP driver
PCI: rockchip: Remove pci_epf_linkup() from Rockchip EP driver
PCI: cadence: Remove pci_epf_linkup() from Cadence EP driver
PCI: pci-epf-test: Use pci_epc_get_features() to get EPC features
PCI: pci-epf-test: Do not allocate next BARs memory if current BAR is 64Bit
PCI: pci-epf-test: Remove setting epf_bar flags in function driver
PCI: endpoint: Fix pci_epf_alloc_space() to set correct MEM TYPE flags
PCI: endpoint: Add helper to get first unreserved BAR
PCI: cadence: Populate ->get_features() cdns_pcie_epc_ops
PCI: rockchip: Populate ->get_features() dw_pcie_ep_ops
PCI: pci-dra7xx: Populate ->get_features() dw_pcie_ep_ops
PCI: designware-plat: Populate ->get_features() dw_pcie_ep_ops
PCI: dwc: Add ->get_features() callback function to dw_pcie_ep_ops
PCI: endpoint: Add new pci_epc_ops to get EPC features
PCI: endpoint: functions: Use memcpy_fromio()/memcpy_toio()
- Add dra72x/dra74x/dra76x SoC compatible strings (Kishon Vijay
Abraham I)
- Enable x2 mode support for dra72x/dra74x/dra76x SoC (Kishon Vijay
Abraham I)
- Configure dra7xx PHY to PCIe mode (Kishon Vijay Abraham I)
- Simplify dwc (remove unnecessary header includes, name variables
consistently, reduce inverted logic, etc) (Gustavo Pimentel)
- Add i.MX8MQ support (Andrey Smirnov)
- Add message to help debug dwc MSI-X mask bit errors (Gustavo Pimentel)
- Work around imx7d PCIe PLL erratum (Trent Piepho)
- Don't assert qcom reset GPIO during probe (Bjorn Andersson)
- Skip dwc MSI init if MSIs have been disabled (Lucas Stach)
* remotes/lorenzo/pci/dwc:
PCI: dwc: skip MSI init if MSIs have been explicitly disabled
PCI: dwc: Remove superfluous shifting in definitions
PCI: dwc: Make use of GENMASK/FIELD_PREP
PCI: dwc: Make use of BIT() in constant definitions
PCI: dwc: Share code for dw_pcie_rd/wr_other_conf()
PCI: dwc: Make use of IS_ALIGNED()
PCI: imx6: Add code to request/control "pcie_aux" clock for i.MX8MQ
dt-bindings: imx6q-pcie: Add "pcie_aux" clock for imx8mq
PCI: qcom: Don't deassert reset GPIO during probe
PCI: imx: Add workaround for e10728, IMX7d PCIe PLL failure
ARM: dts: imx7d: Add node for PCIe PHY
dt-bindings: imx6q-pcie: Add description of imx7d pcie phy
PCI: dwc: Print debug error message when MSI-X entry control mask bit is set
PCI: imx6: Add support for i.MX8MQ
PCI: imx6: Convert DIRECT_SPEED_CHANGE quirk code to use a flag
PCI: imx6: Mark PHY functions as i.MX6 specific
PCI: imx6: Introduce drvdata
PCI: dwc: Replace bit rotation operation (1 << bit) with BIT(bit)
PCI: dwc: Improve code readability and simplify mask/unmask operations
PCI: dwc: Rename variable name from data to d on dw_pcie_irq_domain_free()
PCI: dwc: Rename variable name from data to d on dw_pci_msi_set_affinity()
PCI: dwc: Rename variable name from data to d on dw_pci_setup_msi_msg()
PCI: dwc: Rename variable name from data to d on dw_pci_bottom_mask/unmask()
PCI: dwc: Remove unnecessary header include (signal.h)
PCI: dwc: Remove unnecessary header include (of_gpio.h)
PCI: dwc: dra7xx: Invoke phy_set_mode() API to set PHY mode to PHY_MODE_PCIE
PCI: dwc: dra7xx: Enable x2 mode support for dra74x, dra76x and dra72x
dt-bindings: PCI: dra7xx: Add properties to enable x2 lane in dra7
dt-bindings: PCI: dra7xx: Add SoC specific compatible strings
- Extend altera to support Stratix 10 (Ley Foon Tan)
- Allow building altera driver on ARM64 (Ley Foon Tan)
* remotes/lorenzo/pci/altera:
dt-bindings: PCI: altera: Add altr,pcie-root-port-2.0
PCI: altera: Enable driver on ARM64
PCI: altera: Add Stratix 10 PCIe support
- Blacklist Gigabyte X299 Root Port power management to fix Thunderbolt
hotplug (Mika Westerberg)
- Revert runtime PM suspend/resume callbacks that broke PME on network
cable plug (Mika Westerberg)
- Disable Data Link State Changed interrupts to prevent wakeup
immediately after suspend (Mika Westerberg)
* pci/pm:
PCI/PME: Fix possible use-after-free on remove
PCI/PME: Fix hotplug/sysfs remove deadlock in pcie_pme_remove()
PCI: pciehp: Disable Data Link Layer State Changed event on suspend
Revert "PCI/PME: Implement runtime PM callbacks"
PCI: Blacklist power management of Gigabyte X299 DESIGNARE EX PCIe ports
- Allow portdrv to claim subtractive decode Ports so PCIe services will
work for them (Honghui Zhang)
- Report PCIe links that become degraded at run-time (Alexandru Gagniuc)
* pci/portdrv:
PCI/LINK: Report degraded links via link bandwidth notification
PCI/portdrv: Support PCIe services on subtractive decode bridges
PCI/portdrv: Use conventional Device ID table formatting
- Mark expected switch fall-through (Mathieu Malaterre)
- Use of_node_name_eq() for node name comparisons (Rob Herring)
- Add ACS and pciehp quirks for HXT SD4800 (Shunyong Yang)
- Consolidate Rohm Vendor ID definitions (Andy Shevchenko)
- Use u32 (not __u32) for things not exposed to userspace (Logan
Gunthorpe)
- Fix locking semantics of bus and slot reset interfaces (Alex
Williamson)
- Update PCIEPORTBUS Kconfig help text (Hou Zhiqiang)
* pci/misc:
PCI: Update PCIEPORTBUS Kconfig help text
PCI: Fix "try" semantics of bus and slot reset
PCI: Clean up usage of __u32 type
genirq/msi: Clean up usage of __u8/__u16 types
PCI: Move Rohm Vendor ID to generic list
PCI: pciehp: Add HXT quirk for Command Completed errata
PCI: Add ACS quirk for HXT SD4800
PCI: Add HXT vendor ID
PCI: Use of_node_name_eq() for node name comparisons
PCI: Mark expected switch fall-through
- Reorder pciehp cached state/hardware state updates to avoid missed
interrupts (Mika Westerberg)
- Turn ibmphp semaphores into completions or mutexes (Arnd Bergmann)
* pci/hotplug:
PCI: ibmphp: Turn semaphores into completions or mutexes
PCI: pciehp: Assign ctrl->slot_ctrl before writing it to hardware
- Probe bridge window attributes only once at enumeration-time to fix
device accesses during rescan (Bjorn Helgaas)
- Return BAR size (not "size -1 ") from pci_size() to simplify code (Du
Changbin)
- Use config header type (not class code) identify bridges more reliably
(Honghui Zhang)
- Work around Intel Denverton incorrect Trace Hub BAR size reporting
(Alexander Shishkin)
* pci/enumeration:
x86/PCI: Fixup RTIT_BAR of Intel Denverton Trace Hub
PCI: Rely on config space header type, not class code
PCI: Make pci_size() return real BAR size
PCI: Probe bridge window attributes once at enumeration-time
- Use Latency Tolerance Reporting if already enabled by platform (Bjorn
Helgaas)
- Save/restore LTR info for suspend/resume (Bjorn Helgaas)
* pci/aspm:
PCI/ASPM: Save LTR Capability for suspend/resume
PCI/ASPM: Use LTR if already enabled by platform
The Virtual Channel service has been removed and Downstream Port
Containment has been added, so update the symbol description to be
consistent with the current code.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The commit referenced below introduced device locking around save and
restore of state for each device during a PCI bus "try" reset, making it
decidely non-"try" and prone to deadlock in the event that a device is
already locked. Restore __pci_reset_bus() and __pci_reset_slot() to their
advertised locking semantics by pushing the save and restore functions into
the branch where the entire tree is already locked. Extend the helper
function names with "_locked" and update the comment to reflect this
calling requirement.
Fixes: b014e96d1a ("PCI: Protect pci_error_handlers->reset_notify() usage with device_lock()")
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
