'encap_header' is malloced and should be freed before leaving from
the error handling cases, otherwise it will cause memory leak.
Fixes: 232c001398 ("net/mlx5e: Add support to neighbour update flow")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove including <linux/version.h> that is not needed.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the missing unlock before return from function __ibmvnic_reset()
in the error handling case.
Fixes: ed651a1087 ("ibmvnic: Updated reset handling")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull MD fixes from Shaohua Li:
- Several bug fixes for raid5-cache from Song Liu, mainly handle
journal disk error
- Fix bad block handling in choosing raid1 disk from Tomasz Majchrzak
- Simplify external metadata array sysfs handling from Artur
Paszkiewicz
- Optimize raid0 discard handling from me, now raid0 will dispatch
large discard IO directly to underlayer disks.
* tag 'md/4.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/shli/md:
raid1: prefer disk without bad blocks
md/r5cache: handle sync with data in write back cache
md/r5cache: gracefully handle journal device errors for writeback mode
md/raid1/10: avoid unnecessary locking
md/raid5-cache: in r5l_do_submit_io(), submit io->split_bio first
md/md0: optimize raid0 discard handling
md: don't return -EAGAIN in md_allow_write for external metadata arrays
md/raid5: make use of spin_lock_irq over local_irq_disable + spin_lock
The function is not used, removing it fixes the following warning when
building with clang:
drivers/net/usb/net1080.c:271:20: error: unused function
'nc_dump_ttl' [-Werror,-Wunused-function]
Also remove the definition of TTL_THIS, which is only used in
nc_dump_ttl()
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function is not used, removing it fixes the following warning when
building with clang:
drivers/net/usb/r8152.c:825:5: error: unused function 'usb_ocp_read'
[-Werror,-Wunused-function]
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Don't allow negative TCP reordering values, from Soheil Hassas
Yeganeh.
2) Don't overflow while parsing ipv6 header options, from Craig Gallek.
3) Handle more cleanly the case where an individual route entry during
a dump will not fit into the allocated netlink SKB, from David
Ahern.
4) Add missing CONFIG_INET dependency for mlx5e, from Arnd Bergmann.
5) Allow neighbour updates to converge more quickly via gratuitous
ARPs, from Ihar Hrachyshka.
6) Fix compile error from CONFIG_INET is disabled, from Eric Dumazet.
7) Fix use after free in x25 protocol init, from Lin Zhang.
8) Valid VLAN pvid ranges passed into br_validate(), from Tobias
Jungel.
9) NULL out address lists in child sockets in SCTP, this is similar to
the fix we made for inet connection sockets last week. From Eric
Dumazet.
10) Fix NULL deref in mlxsw driver, from Ido Schimmel.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (27 commits)
mlxsw: spectrum: Avoid possible NULL pointer dereference
sh_eth: Do not print an error message for probe deferral
sh_eth: Use platform device for printing before register_netdev()
mlxsw: spectrum_router: Fix rif counter freeing routine
mlxsw: spectrum_dpipe: Fix incorrect entry index
cxgb4: update latest firmware version supported
qmi_wwan: add another Lenovo EM74xx device ID
sctp: do not inherit ipv6_{mc|ac|fl}_list from parent
udp: make *udp*_queue_rcv_skb() functions static
bridge: netlink: check vlan_default_pvid range
net: ethernet: faraday: To support device tree usage.
net: x25: fix one potential use-after-free issue
bpf: adjust verifier heuristics
ipv6: Check ip6_find_1stfragopt() return value properly.
selftests/bpf: fix broken build due to types.h
bnxt_en: Check status of firmware DCBX agent before setting DCB_CAP_DCBX_HOST.
bnxt_en: Call bnxt_dcb_init() after getting firmware DCBX configuration.
net: fix compile error in skb_orphan_partial()
ipv6: Prevent overrun when parsing v6 header options
neighbour: update neigh timestamps iff update is effective
...
- fix headers_install to not delete pre-existing headers
in the install destination
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=vhLf
-----END PGP SIGNATURE-----
Merge tag 'kbuild-fixes-v4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild fix from Masahiro Yamada:
"Fix headers_install to not delete pre-existing headers in the install
destination"
* tag 'kbuild-fixes-v4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kbuild: skip install/check of headers right under uapi directories
This pushes qed [and as result, all qed* drivers] into using 8.20.0.0
firmware. The changes are mostly contained in qed with minor changes
to qedi due to some HSI changes.
Content-wise, the firmware contains fixes to various issues exposed
since the release of the previous firmware, including:
- Corrects iSCSI fast retransmit when data digest is enabled.
- Stop draining packets when receiving several consecutive PFCs.
- Prevent possible assertion when consecutively opening/closing
many connections.
- Prevent possible assertion due to too long BDQ fetch time.
In addition, the new firmware would allow us to later add iWARP support
in qed and qedr.
Changes from previous version
-----------------------------
- V2: Fix warning in qed_debug.c
Signed-off-by: Chad Dupuis <Chad.Dupuis@cavium.com>
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Manish Rangankar <Manish.Rangankar@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skbs in (re)transmit queue no longer have a copy of jiffies
at the time of the transmit : skb->skb_mstamp is now in usec unit,
with no correlation to tcp_jiffies32.
We have to convert rto from jiffies to usec, compute a time difference
in usec, then convert the delta to HZ units.
Fixes: 9a568de481 ("tcp: switch TCP TS option (RFC 7323) to 1ms clock")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull pid namespace fixes from Eric Biederman:
"These are two bugs that turn out to have simple fixes that were
reported during the merge window. Both of these issues have existed
for a while and it just happens that they both were reported at almost
the same time"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
pid_ns: Fix race between setns'ed fork() and zap_pid_ns_processes()
pid_ns: Sleep in TASK_INTERRUPTIBLE in zap_pid_ns_processes
In case we got an FDB notification for a port that doesn't exist we
execute an FDB entry delete to prevent it from re-appearing the next
time we poll for notifications.
If the operation failed we would trigger a NULL pointer dereference as
'mlxsw_sp_port' is NULL.
Fix it by reporting the error using the underlying bus device instead.
Fixes: 12f1501e75 ("mlxsw: spectrum: remove FDB entry in case we get unknown object notification")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
octeon_devices_lock can be made static as it does not need to be
in global scope.
Cleans up sparse warning: "warning: symbol 'octeon_devices_lock'
was not declared. Should it be static?"
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
EPROBE_DEFER is not an error, hence printing an error message like
sh-eth ee700000.ethernet: failed to initialise MDIO
may confuse the user.
To fix this, suppress the error message in case of probe deferral.
While at it, shorten the message, and add the actual error code.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MDIO initialization failure message is printed using the network
device, before it has been registered, leading to:
(null): failed to initialise MDIO
Use the platform device instead to fix this:
sh-eth ee700000.ethernet: failed to initialise MDIO
Fixes: daacf03f0b ("sh_eth: Register MDIO bus before registering the network device")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEE4bay/IylYqM/npjQHv7KIOw4HPYFAlkdXckTHG1rbEBwZW5n
dXRyb25peC5kZQAKCRAe/sog7Dgc9nmsB/0alLYsQdFCSSH6QY0xdAJXzHYuojXf
OXIG128k2oLRIr67RIkyrWT+uLvfGbT4Xnve30gegsRIx2bQ/cDvyh/LTy0I9x5+
zf6Sw3ayg2Qg/QaOi5raYXGyiBPD9Amcp9sOo/z7hxWUx6NWSHuZeLJUYcerEcK9
TTaMtcb+rgbbydJBQ4tL0I+Z0suNtPXYCzVDfV57FJjPl8wM/KlduPrFhaqoNliD
cFXDVrPx/vdHkQ1LzHrVtftctxhJZR7n6B8N+bMD5IpV2753wrWf8gXMdWpuD913
WOoZQRH9GK2nw3QuLKLs7Y85RMgiyz8iZacSYv5r2MN7UNJ3wBLvQYYE
=N66w
-----END PGP SIGNATURE-----
Merge tag 'linux-can-next-for-4.13-20170518' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2017-05-18
this is a pull request of 4 patches for net-next/master.
All 4 patches are by Quentin Schulz, they add deep deep Suspend/Resume
support to the m_can driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/mellanox/mlxsw//spectrum_dpipe.c:221:52: warning:
Using plain integer as NULL pointer
drivers/net/ethernet/mellanox/mlxsw//spectrum_dpipe.c:221:74: warning:
Using plain integer as NULL pointer
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko says:
====================
mlxsw: couple of fixes
Couple of fixes from Arkadi
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
During rif counter freeing the counter index can be invalid. Add check
of validity before freeing the counter.
Fixes: e0c0afd8aa ("mlxsw: spectrum: Support for counters on router interfaces")
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of disabled counters the entry index will be incorrect. Fix this
by moving the entry index set before the counter status check.
Fixes: 2ba5999f00 ("mlxsw: spectrum: Add Support for erif table entries access")
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cygnus is a small family of SoCs, of which we currently have
devicetree for BCM11360 and BCM58300. The 11360's B53 is mostly the
same as 58xx, just requiring a tiny bit of setup that was previously
missing.
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot says:
====================
net: dsa: headers cleanup
The DSA core files share a common private header file. Include the DSA
public header there instead of independently in each core source file.
DSA core and its drivers use switchdev, thus include switchdev.h in the
public DSA header. This allows us to get rid of the forward declaration
and use typedef defined by switchdev.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the DSA public header includes switchdev.h, use the provided
switchdev_obj_dump_cb_t typedef for the object dump callback.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DSA drivers and core use switchdev. Include switchdev.h only once, in
the dsa.h public header, so that inclusion in DSA drivers or forward
declarations of switchdev structures in not necessary anymore.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The public include/net/dsa.h file is meant for DSA drivers, while all
DSA core files share a common private header net/dsa/dsa_priv.h file.
Ensure that dsa_priv.h is the only DSA core file to include net/dsa.h,
and add a new line to separate absolute and relative headers at the same
time.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function has to return NULL on a error case, because there is a
separate error variable.
The offset has to be changed only if skb is returned
v2: fix udp code to not use an extra variable
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: David S. Miller <davem@davemloft.net>
Fixes: 65101aeca5 ("net/sock: factor out dequeue/peek with offset cod")
Signed-off-by: Andrei Vagin <avagin@openvz.org>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change t4fw_version.h to update latest firmware version
number to 1.16.43.0.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for hdlc-bus mode to the fsl_ucc_hdlc driver. This can
be enabled with the "fsl,hdlc-bus" property in the DTS node of the
corresponding ucc.
This aligns the configuration of the UPSMR and GUMR registers to what is
done in our ucc_hdlc driver (that only support hdlc-bus mode) and with
the QuickEngine's documentation for hdlc-bus mode.
GUMR/SYNL is set to AUTO for the busmode as in this case the CD signal
is ignored. The brkpt_support is enabled to set the HBM1 bit in the
CMXUCR register to configure an open-drain connected HDLC bus.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Cc: Zhao Qiang <qiang.zhao@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the bitmask for the two bit SYNL register according to the QUICK
Engine Reference Manual.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Cc: Zhao Qiang <qiang.zhao@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can't assume that we are always in loopback mode if rx and tx clock
have the same clock source. If we want to use HDLC busmode we also have
the same clock source but we are not in loopback mode. So move the
setting of the baudrate generator after the check for property for the
loopback mode.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Cc: Zhao Qiang <qiang.zhao@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need space for the struct qe_bd and not for a pointer to this struct.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Cc: Zhao Qiang <qiang.zhao@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes the following compiler warnings:
drivers/net/wan/fsl_ucc_hdlc.c: In function 'ucc_hdlc_poll':
warning: 'skb' may be used uninitialized in this function
[-Wmaybe-uninitialized]
skb->mac_header = skb->data - skb->head;
and
drivers/net/wan/fsl_ucc_hdlc.c: In function 'ucc_hdlc_probe':
drivers/net/wan/fsl_ucc_hdlc.c:1127:3: warning: 'utdm' may be used
uninitialized in this function [-Wmaybe-uninitialized]
kfree(utdm);
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Cc: Zhao Qiang <qiang.zhao@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the tracing seems to be remaining traces for basic driver
development. They can be removed now, as they cause noisy printouts.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Cc: Zhao Qiang <qiang.zhao@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In their infinite wisdom, and never ending quest for end user frustration,
Lenovo has decided to use a new USB device ID for the wwan modules in
their 2017 laptops. The actual hardware is still the Sierra Wireless
EM7455 or EM7430, depending on region.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
SCTP needs fixes similar to 83eaddab43 ("ipv6/dccp: do not inherit
ipv6_mc_list from parent"), otherwise bad things can happen.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the udp memory accounting refactor, we don't need any more
to export the *udp*_queue_rcv_skb(). Make them static and fix
a couple of sparse warnings:
net/ipv4/udp.c:1615:5: warning: symbol 'udp_queue_rcv_skb' was not
declared. Should it be static?
net/ipv6/udp.c:572:5: warning: symbol 'udpv6_queue_rcv_skb' was not
declared. Should it be static?
Fixes: 850cbaddb5 ("udp: use it's own memory accounting schema")
Fixes: c915fe13cb ("udplite: fix NULL pointer dereference")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently it is allowed to set the default pvid of a bridge to a value
above VLAN_VID_MASK (0xfff). This patch adds a check to br_validate and
returns -EINVAL in case the pvid is out of bounds.
Reproduce by calling:
[root@test ~]# ip l a type bridge
[root@test ~]# ip l a type dummy
[root@test ~]# ip l s bridge0 type bridge vlan_filtering 1
[root@test ~]# ip l s bridge0 type bridge vlan_default_pvid 9999
[root@test ~]# ip l s dummy0 master bridge0
[root@test ~]# bridge vlan
port vlan ids
bridge0 9999 PVID Egress Untagged
dummy0 9999 PVID Egress Untagged
Fixes: 0f963b7592 ("bridge: netlink: add support for default_pvid")
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Tobias Jungel <tobias.jungel@bisdn.de>
Acked-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Function udp_skb_dtor_locked does not need to be in global scope
so make it static to fix sparse warning:
net/ipv4/udp.c: warning: symbol 'udp_skb_dtor_locked' was not
declared. Should it be static?
Fixes: 6dfb4367cd ("udp: keep the sk_receive_queue held when splicing")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jason Wang says:
====================
vhost_net rx batch dequeuing
This series tries to implement rx batching for vhost-net. This is done
by batching the dequeuing from skb_array which was exported by
underlayer socket and pass the sbk back through msg_control to finish
userspace copying. This is also the requirement for more batching
implemention on rx path.
Tests shows at most 7.56% improvment bon rx pps on top of batch
zeroing and no obvious changes for TCP_STREAM/TCP_RR result.
Please review.
Thanks
Changes from V4:
- drop batch zeroing patch
- renew the performance numbers
- move skb pointer array out of vhost_net structure
Changes from V3:
- add batch zeroing patch to fix the build warnings
Changes from V2:
- rebase to net-next HEAD
- use unconsume helpers to put skb back on releasing
- introduce and use vhost_net internal buffer helpers
- renew performance numbers on top of batch zeroing
Changes from V1:
- switch to use for() in __ptr_ring_consume_batched()
- rename peek_head_len_batched() to fetch_skbs()
- use skb_array_consume_batched() instead of
skb_array_consume_batched_bh() since no consumer run in bh
- drop the lockless peeking patch since skb_array could be resized, so
it's not safe to call lockless one
====================
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We used to dequeue one skb during recvmsg() from skb_array, this could
be inefficient because of the bad cache utilization and spinlock
touching for each packet. This patch tries to batch them by calling
batch dequeuing helpers explicitly on the exported skb array and pass
the skb back through msg_control for underlayer socket to finish the
userspace copying. Batch dequeuing is also the requirement for more
batching improvement on receive path.
Tests were done by pktgen on tap with XDP1 in guest. Host is Intel(R)
Xeon(R) CPU E5-2650 0 @ 2.00GHz.
rx batch | pps
0 2.25Mpps
1 2.33Mpps (+3.56%)
4 2.33Mpps (+3.56%)
16 2.35Mpps (+4.44%)
64 2.42Mpps (+7.56%) <- Default rx batching
128 2.40Mpps (+6.67%)
256 2.38Mpps (+5.78%)
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes tap_recvmsg() can receive from skb from its caller
through msg_control. Vhost_net will be the first user.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
