The LDO28 is used only on Odroid XU3 for Display Port. Define it so DTS
will describe entire hardware.
Depending on bootloader behavior this might affect the Display Port
because none of drivers are enabling it. By default it is off in S2MPS11
PMIC reset values. However it could be enabled by bootloader so in such
case kernel will later disable it as unused regulator.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
The LED nodes can be shared between Odroid XU3, XU3-Lite and XU (not yet
added) thus removing duplication.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
DWC3 device found on Exynos SoCs cannot work in OTG mode alone, because
it lacks some OTG related control part. OTG mode operation is possible
only with external hardware logic (usually GPIO-based) specific to
the board. Right now, however, there is no driver for such logic and no
bindings, so the OTG mode is dysfunctional at all (this means that it
doesn't work as a peripheral nor as a host). This patch sets the operation
mode to peripheral to get DWC3_1 device at least somehow working. This can
be later updated, when proper OTG driver and bindings get developed.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Add Hardkernel Odroid XU4 board Device Tree sources. The board differs
from Odroid XU3 and XU3-Lite by:
1. No green and red LEDs (except standard red power LED).
2. Only two PWM outputs are used (fan and blue LED)
3. No audio codec.
4. Two USB3 ports in host mode (no micro USB3 connector for OTG).
5. Realtek RTL8153-CG gigabit network adapter (instead of SMSC9514).
6. Additional connector with IO ports (I2S_0, I2C_5).
7. No DisplayPort (like XU3-Lite).
8. No TI INA231 power measurement sensors (like XU3-Lite).
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The Odroid XU4 board does not have audio codec so before adding DTS
for new board split the audio codec to separate DTSI file. Include
the audio codec DTSI in Odroid XU3 and XU3-Lite boards.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The Odroid XU3 Lite is almost the same as XU3, except:
1. Lower CPU frequencies (1.8 GHz for A15 and 1.3 GHz for A7, instead of
2.0 GHz and 1.4 GHz).
2. No DisplayPort.
3. No TI INA231 energy measurement sensors.
This patch moves common nodes (which is almost everything) to a common
DTSI file and adds a new XU3 Lite DTS.
Currently in comparison to XU3, only the INA231 sensors are disabled to
remove the warning:
ina2xx 0-0040: error configuring the device: -6
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The IRQB of S2MPS11 PMIC is wired to XEINT4 (GPX0-4) through pull-up
resistor.
Add interrupt properties and pinctrl configuration to enable RTC wake
alarm of rtc-s5m driver. This also removes a warning:
sec_pmic 4-0066: No interrupt specified, no interrupts
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
PWM output wasn't working because it wasn't hooked up to its pincontrol.
This patch:
- hooks up PWM to its pincontrol, and documents what
the outputs are on the XU3
- switches the LEDs that are on PWM outputs to use PWM
rather than GPIO.
The main effect is that the brightness of the LEDs can be controlled, and
user-mode fan control is enabled via /sys/class/pwm
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Peter Chubb <peter.chubb@nicta.com.au>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Add MAX98090 audio codec, I2S interface and the sound nodes
to support audio on exynos5422-odroidxu3 board. Now we can
support audio using simple-audio-card DT binding.
Signed-off-by: Inha Song <ideal.song@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Tested-by: Markus Reichl <m.reichl@fivetechno.de>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The Exynos5422 SoC has a s3c6410 RTC where the source clock
is now a mandatory property.
This patch fixes probe failure of s3c-rtc on Odroid-XU3 boards.
Signed-off-by: Markus Reichl <m.reichl@fivetechno.de>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
HS400 timing values are added for exynos5422-odroidxu3 board.
Signed-off-by: Markus Reichl <m.reichl@fivetechno.de>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
This patch adds the RGB-LED on XU3 as 3 gpio-leds.
Signed-off-by: Markus Reichl <m.reichl@fivetechno.de>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The patch adds gpio for detecting presence of MMC card.
It fixes issue with kernel hang when MMC card is missing.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The Exynos5420 SoC has 3 sets of 8 pads used as data lines for the 3
MMC/SD/SDIO slots. These needs to be muxed as SD_n_DATA instead of a
GPIO or external interrupt to allow the MMC controller to communicate
with the attached cards or SDIO devices.
Which data lines needs to be muxed as SD_n_DATA depends on the bus
width used for data transfer:
* bus-width = <1> needs SD_n_DATA[0]
* bus-width = <4> needs SD_n_DATA[0-3]
* bus-width = <8> needs SD_n_DATA[0-7]
The Exynos5250-pinctrl.dtsi file that defines the groups of pins has
SD_n_DATA[0] muxed for both sdn_bus1 and sdn_bus4 so just one of them
needs to be included in the device node's pinctrl property.
But Exynos5420-pinctrl has a different definition and only includes
SD_n_DATA[1-3] for sdn_bus4. So for a bus-width = <4>, both sdn_bus1
and sdn_bus4 have to be in the dev pinctrl to mux all the needed pads.
It seems all Exynos5420 boards had just cargo cult the pinctrl lines
assuming that sdn_bus4 also included SD_n_DATA[0] and it only works
because the bootloader muxes the pads correctly. But that is not the
case for the devices not used by the bootloader such as WiFi modules.
Add sdn_bus1 too in the nodes pinctrl to not rely on the bootloader.
Suggested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
This patch adds reset-gpios property to the eMMC slot, so the MMC driver
is able to properly reset eMMC card on system restart and thus fixes
system hang on software reboot.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Last 22 MiB is RAM is reserved by secure monitor code and cannot be
accessed from Linux kernel, so adjust total RAM size to 0x7EA00000
(2 GiB - 22 MiB). This fixes random 'imprecise kernel abort' kernel
failures.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The odroid-xu3 has 4 INA231 current sensors on board which can be
accessed from the Linux via the hwmon interface.
There is one sensor for each of these power rails:
- A15 cluster: VDD_ARM
- A7 cluster: VDD_KFC
- GPU: VDD_G3D
- memory: VDD_MEM
In addition to adding the sensors, LDO26 from the PMIC needs to be
enabled because it's powering these sensor.
Cc: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Cc: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Add DTS for the Hardkernel Odroid XU3. The name of the DTS file is
kept the same as the vendors naming, which means it's prefixed with
exynos5422 instead of exynos5800 as the SoC name even though it
includes the exyno5800 dtsi.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Kukjin Kim <kgene@kernel.org>