drivers/i2c/busses/i2c-rk3x.c:610:69-70: rk3x_i2c_match is not NULL terminated at line 610
Make sure of_device_id tables are NULL terminated
Generated by: /kbuild/src/linux/scripts/coccinelle/misc/of_table.cocci
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fixes:
>> drivers/i2c/busses/i2c-sun6i-p2wi.c:243:10: warning: 'ret' may be used uninitialized in this function [-Wmaybe-uninitialized]
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The P2WI controller looks like an SMBus controller which only supports byte
data transfers. But, it differs from standard SMBus protocol on several
aspects:
- it supports only one slave device, and thus drop the address field
- it adds a parity bit every 8bits of data
- only one read access is required to read a byte (instead of a write
followed by a read access in standard SMBus protocol)
- there's no Ack bit after each byte transfer
This means this bus cannot be used to interface with standard SMBus
devices (the only known device to support this interface is the AXP221
PMIC).
However the P2WI protocol is close enough to SMBus to be integrated in
the I2C subsystem (see this thread [1] for detailed reasons that led to
integrating this driver in the I2C subsystem).
[1] http://www.spinics.net/lists/linux-i2c/msg15066.html
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Driver for the native I2C adapter found in Rockchip RK3xxx SoCs.
Configuration is only possible through devicetree. The driver is
interrupt driven and supports the I2C_M_IGNORE_NAK mangling bit.
Signed-off-by: Max Schwarz <max.schwarz@online.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull i2c updates from Wolfram Sang:
"I2C has the following updates for 3.16:
- major cleanups to the rcar and sh_mobile drivers
- removal of nuc900 driver which had a compile error for years
- usual bunch of driver updates, bugfixes and cleanups"
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (44 commits)
i2c: pca954x: Fix compilation without CONFIG_GPIOLIB
i2c: mux: pca954x: Use the descriptor-based GPIO API
i2c: mpc: insert DR read in i2c_fixup()
i2c: bfin: turn to Resource-managed API in probe function
i2c: Make of_device_id array const
i2c: remove unnecessary OOM messages
i2c: designware-pci: Add Haswell PCI IDs
i2c: designware: Add runtime PM hooks
i2c: designware: Disable device on system suspend
i2c: nuc900: remove driver
i2c: imx: update i2c clock divider for each transaction
i2c: imx: fix the i2c bus hang issue when do repeat restart
i2c: rcar: update copyright and license information
i2c: rcar: janitorial cleanup after refactoring
i2c: rcar: reuse status bits as enable bits
i2c: rcar: remove spinlock
i2c: rcar: refactor status bit handling
i2c: rcar: refactor setting up msg
i2c: rcar: check bus free before first message
i2c: rcar: refactor irq state machine
...
The mpc_i2c_fixup function is called when the bus is not released by a
slave. The function generates 9 pulses that should lead the slave
to release the bus.
The sequence that generates the pulses disables/enables the I2C module
that controls the blocked bus. We have found out on the P2041 SoC that
this could cause the CPU to hang (for a short delay).
To avoid this, this patch introduces a read to the I2CDR register
between the re-enablement of the I2C module in master mode and its
returning to the slave mode instead of the delay (the final delay,
between the pulses is kept), as proposed in procedure from the P2041
reference manual (16.6.2.3), and the other manuals from the mpc83xx and
mpc85xx families.
Signed-off-by: Rainer Boschung <rainer.boschung@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
On ARM Chromebooks we have a few devices that are accessed by both the
AP (the main "Application Processor") and the EC (the Embedded
Controller). These are:
* The battery (sbs-battery).
* The power management unit tps65090.
On the original Samsung ARM Chromebook these devices were on an I2C
bus that was shared between the AP and the EC and arbitrated using
some extranal GPIOs (see i2c-arb-gpio-challenge).
The original arbitration scheme worked well enough but had some
downsides:
* It was nonstandard (not using standard I2C multimaster)
* It only worked if the EC-AP communication was I2C
* It was relatively hard to debug problems (hard to tell if i2c issues
were caused by the EC, the AP, or some device on the bus).
On the HP Chromebook 11 the design was changed to:
* The AP/EC comms were still i2c, but the battery/tps65090 were no
longer on the bus used for AP/EC communication. The battery was
exposed to the AP through a limited i2c tunnel and tps65090 was
exposed to the AP through a custom Linux driver.
On the Samsung ARM Chromebook 2 the scheme is changed yet again, now:
* The AP/EC comms are now using SPI for faster speeds.
* The EC's i2c bus is exposed to the AP through a full i2c tunnel.
The upstream "tegra124-venice2" uses the same scheme as the Samsung
ARM Chromebook 2, though it has a different set of components on the
other side of the bus.
This driver supports the scheme used by the Samsung ARM Chromebook 2.
Future patches to this driver could add support for the battery tunnel
on the HP Chromebook 11 (and perhaps could even be used to access
tps65090 on the HP Chromebook 11 instead of using a special driver,
but I haven't researched that enough).
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Make of_device_id array const, because all OF functions
handle it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message. For example,
k.alloc and v.alloc failures use dump_stack().
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Intel Haswell has the same I2C host controller than Baytrail and it can
also be enumerated as a PCI device. Add the PCI IDs to the driver list.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
It is possible that after entering runtime PM suspend the controller
context is lost due the fact that its power is removed. This happens for
example on Asus T100, an Intel Baytrail based tablet/laptop.
In order to get the controller back to functional state, we need to
implement runtime PM hooks which will re-initialize the hardware during
runtime PM resume. We can re-use the existing system suspend hooks as the
steps to resume/suspend the controller are the same.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Userspace can initiate system suspend on arbitrary times which means that
device drivers must make sure that their device gets quiesced before system
suspend is entered. Therefore disable the I2C host controller in the driver
system suspend hook.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Arnd said in another patch:
"As far as I can tell, this driver must have produced this
error for as long as it has been merged into the mainline kernel, but
it was never part of the normal build tests:
drivers/i2c/busses/i2c-nuc900.c: In function 'nuc900_i2c_probe':
drivers/i2c/busses/i2c-nuc900.c:601:17: error: request for member
'apbfreq' in something not a structure or union
ret = (i2c->clk.apbfreq)/(pdata->bus_freq * 5) - 1;
^
This is an attempt to get the driver to build and possibly
work correctly, although I do wonder whether we should just
remove it, as it has clearly never worked."
I agree with removing it since nobody showed interest in Arnd's fixup
patch.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: Wan ZongShun <mcuos.com@gmail.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Since IMX serial SOCs support low bus freq mode, some clocks freq
may change to save power. I2C needs to check the clock source and
update the divider.
For example:
i.MX6SL I2C clk is from IPG_PERCLK which is sourced from IPG_CLK.
Under normal operation, IPG_CLK is 66MHz, ipg_perclk is at 22MHz.
In low bus freq mode, IPG_CLK is at 12MHz and IPG_PERCLK is down
to 4MHz. So the I2C driver must update the divider register for
each transaction when the current IPG_PERCLK is not equal to the
clock of previous transaction.
Signed-off-by: Fugang Duan <B38611@freescale.com>
[wsa: removed an outdated comment and simplified debug output]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Test i2c device Maxim max44009, datasheet is located at:
http://www.maximintegrated.com/datasheet/index.mvp/id/7175
The max44009 support repeat operation like:
read -> repeat restart -> read/write
The current i2c imx host controller driver don't support this
operation that causes i2c bus hang due to "MTX" is cleared in
.i2c_imx_read(). If "read" is the last message there have no problem,
so the current driver supports all SMbus operation like:
write -> repeat restart -> read/write
IMX i2c controller for master receiver has some limitation:
- If it is the last byte for one operation, it must generate STOP
signal before read I2DR to prevent controller from generating another
clock cycle.
- If it is the last byte in the read, and then do repeat restart, it must
set "MTX" before read I2DR to prevent controller from generating another
extra clock cycle.
The patch is to fix the issue.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Make clear that the driver is GPL v2 only. Remove FSF address. Remove
filename in comment. Update copyright information.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Remove some obvious comments, remove some superfluous debug output (the
error code carries the same information), some white space fixing...
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Status register and enable register are identical regarding their
layout. Use the bit definitions for both.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The i2c core has per-adapter locks, so no need to protect again.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The old macros made it harder to see what was actually happening.
Replace them with something more readable.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Setting up a read or write message is similar enough to be done in one
function. Also, move a helper function into the new function since it is
only used here.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We should always check if the bus is free, independently if it is a read
or write. It should be done before the first message, though. After
that, we ourselves keep the bus busy. Remove a 'ret' assignment which
only silenced a build warning.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Remove the seperate functions and use designated constants. As readable
but less overhead. Actually, this is even more readable since the old
function used a mix of "=" and "|=".
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Remove the seperate functions and use designated constants. As readable
but less overhead.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We use devm, so irq number is only needed during probe.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Very basic operations, just called once, can also go to the caller.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use devm_gpio_request() to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Reviewed-by: Violeta Menendez <violeta.menendez@codethink.co.uk>
Reviewed-by: Ian Molton <ian.molton@codethink.co.uk>
Tested-by: Violeta Menendez <violeta.menendez@codethink.co.uk>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The i2c-eg20t driver is for a companion chip to the Intel Atom E600
series processors. These are 32-bit x86 processors so the driver is
only needed on X86_32. Add COMPILE_TEST as an alternative, so that the
driver can still be build-tested elsewhere.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Newer SoCs have so fast input clocks that the ICCL/H registers only
count every second clock to have a meaningful 9-bit range. The driver
was already prepared for that happening, but didn't use it so far.
Add the proper DT configuration for SoCs that need it.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Due to misconfiguration, it can happen that the calculated timing
parameters are out of range. Bail out if that happens. We can also
simplify some logic later because of the verified value. Also, make the
printouts of the values more precise by adding the hex-prefixes.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
sh_mobile_i2c_init() could detect wrong settings, but didn't bail out,
so it would continue unconfigured. Fix this.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Following the KISS principle, remove unneeded stuff.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This is what devm was made for. No rollback mechanism needed, remove the
hook parameter from the irq setup function and simplify it. While we are
here change some variables to proper types.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Convert the easy parts to devm. irqs will be converted in a seperate
patch to keep diffs readable.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use standard i2c error codes for i2c failures. Also, don't print
something on timeout since it happens regularly with i2c. Simplify some,
logic, too.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
No functional change, binaries are identical.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
HSI2C module on Exynos5260 differs from current modules in
following ways:
1. HSI2C on Exynos5260 has fifo_depth of 16bytes
2. Module needs to be reset as a part of init sequence.
Hence, Following changes are involved.
1. Add a new compatible string and Updates the Documentation dt bindings.
2. Introduce a variant struct to support the changes in H/W
3. Reset the module during init. Thus, bringing the module back
to default state irrespective of what firmware did with it.
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fixed most checkpatch.pl issues
Signed-off-by: Richard Leitner <me@g0hl1n.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
For !CONFIG_PM_RUNTIME, the device were never put back into active
state while resuming.
For CONFIG_PM_RUNTIME, we blindly trusted the device to be inactive
while we were about to handle it at suspend late, which is just too
optimistic.
Even if the driver uses pm_runtime_put_sync() after each tranfer to
return it's runtime PM resources, there are no guarantees this will
actually mean the device will inactivated. The reason is that the PM
core will prevent runtime suspend during system suspend, and thus when
a transfer occurs during the early phases of system suspend the device
will be kept active after the transfer.
To handle both issues above, use pm_runtime_force_suspend|resume() from
the system suspend|resume callbacks.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The smbus block read is not currently supported for imx i2c devices.
This patchset adds the support to imx i2c bus so that blocks of data
can be read using SMbus block reads.(using i2c_smbus_read_block_data()
function from the i2c_core.c.). Tested with 3.10.9 kernel.
Reviewed-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Kaushal Butala <kaushalkernelmailinglist@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The Allwinner A10 compatibles were following a slightly different compatible
patterns than the rest of the SoCs for historical reasons. Move to the other
pattern for consistency across all Allwinner Socs.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
[wsa: dropped binding OK as per
http://lists.infradead.org/pipermail/linux-arm-kernel/2014-February/229438.html]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This hardware does not support zero length transfers. Instead, the
driver does one (random) byte transfers currently with undefined results
for the slaves. We now bail out.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
This patch corrects the error check on the call to pm_runtime_get_sync.
Signed-off-by: Andy Gross <agross@codeaurora.org>
Reviewed-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Don't unmark the device as suspended until after it's been re-setup.
The main race would be w.r.t. an i2c driver that gets resumed at the same
time (asyncronously), that is allowed to do a transfer since suspended
is set to 0 before reinit, but really should have seen the -EIO return
instead.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
There have been "i2c_designware 80860F41:00: controller timed out" errors
on a number of Baytrail platforms. The issue is caused by incorrect value in
Interrupt Mask Register (DW_IC_INTR_MASK) when i2c core is being enabled.
This causes call to __i2c_dw_enable() to immediately start the transfer which
leads to timeout. There are 3 failure modes observed:
1. Failure in S0 to S3 resume path
The default value after reset for DW_IC_INTR_MASK is 0x8ff. When we start
the first transaction after resuming from system sleep, TX_EMPTY interrupt
is already unmasked because of the hardware default.
2. Failure in normal operational path
This failure happens rarely and is hard to reproduce. Debug trace showed that
DW_IC_INTR_MASK had value of 0x254 when failure occurred, which meant
TX_EMPTY was unmasked.
3. Failure in S3 to S0 suspend path
This failure also happens rarely and is hard to reproduce. Adding debug trace
that read DW_IC_INTR_MASK made this failure not reproducible. But from ISR
call trace we could conclude TX_EMPTY was unmasked when problem occurred.
The patch masks all interrupts before the controller is enabled to resolve the
faulty DW_IC_INTR_MASK conditions.
Signed-off-by: Wenkai Du <wenkai.du@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
[wsa: improved the comment and removed typo in commit msg]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
