b2c2-flexcop, dvb/bt8xx and video/bt8xx fails to build on ARM with:
__bad_udelay is specifically designed on ARM to fail when udelay is
called in a bad way. arch/arm/include/asm/delay.h has this to say
about __bad_udelay:
/*
* This function intentionally does not exist; if you see references to
* it, it means that you're calling udelay() with an out of range value.
*
* With currently imposed limits, this means that we support a max delay
* of 2000us. Further limits: HZ<=1000 and bogomips<=3355
*/
extern void __bad_udelay(void);
Solution is to replace udelay by a mdelay and udelay with value less than 2000
Signed-off-by: Thierry MERLE <thierry.merle@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
budget.ko fails to build on ARM with:
ERROR: "__bad_udelay" [drivers/media/dvb/ttpci/budget.ko] undefined!
make[1]: *** [__modpost] Error 1
__bad_udelay is specifically designed on ARM to fail when udelay is
called in a bad way. arch/arm/include/asm/delay.h has this to say
about __bad_udelay:
/*
* This function intentionally does not exist; if you see references to
* it, it means that you're calling udelay() with an out of range value.
*
* With currently imposed limits, this means that we support a max delay
* of 2000us. Further limits: HZ<=1000 and bogomips<=3355
*/
extern void __bad_udelay(void);
Solution is to replace udelay by a mdelay and udelay with value less than 2000
Acked-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Thierry MERLE <thierry.merle@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- Adjust hstart in ov7630 on sn9c103 initdata to shift bayer pattern, this is
the same change as done for the other initdata tables in a previous patch.
- Assign usb-id's for the ov7630 + sn9c103 to gspca if gspca and sn9c102
drivers are both enabled.
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-Make raw bayer header size change from 20 to 16 affect rev072a only, my 2
rev012a cams both have a header size of 20
-While testing this I also tested the new exposure setting (good work on
finding the register JF), and after quite a bit of testing have found out the
exact meaning of the register, this patch modifies setexposure to control
the exposure over a much wider range.
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When using the sonixb driver in a dark room and given that the autoexposure
algorithm starts with a setting most suitable for daylight, the picture
produced by the cam may actually be 100% black leading to a avg_lum value of 0,
so an avg_lum value of 0 does not always signal an exposure settings change
(which it normally does). This patch adds a check for the really black image
case and stops dropping all frames as invalid in this case.
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch makes gspca claim the USB-ID for sn9c101/2 cams with a TAS5110C1B
sensor even if both gspca and sn9c102 are enabled, as these cams are much
better supported under gspca (and extensively tested with gspca).
It also removes an usb-id from sn9c102 for one more unsupported bridge
sensor combo.
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- Add documentation for some known registers
- Add support for vga modes (320x240, 160x120) for sif sensors
- Remove F_RAW sensor flag raw mode should work on any sensor as its a bridge
only thing and keeping the flag was becoming awkward.
- Fixup ov6650 and pas106 auto exposure window settings
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
bnx2x: Accessing un-mapped page
ath9k: Fix TX control flag use for no ACK and RTS/CTS
ath9k: Fix TX status reporting
iwlwifi: fix STATUS_EXIT_PENDING is not set on pci_remove
iwlwifi: call apm stop on exit
iwlwifi: fix Tx cmd memory allocation failure handling
iwlwifi: fix rx_chain computation
iwlwifi: fix station mimo power save values
iwlwifi: remove false rxon if rx chain changes
iwlwifi: fix hidden ssid discovery in passive channels
iwlwifi: W/A for the TSF correction in IBSS
netxen: Remove workaround for chipset quirk
pcnet-cs, axnet_cs: add new IDs, remove dup ID with less info
ixgbe: initialize interrupt throttle rate
net/usb/pegasus: avoid hundreds of diagnostics
tipc: Don't use structure names which easily globally conflict.
The allocated RX buffer size was 64 bytes bigger than the PCI mapped
size with no good reason. If the packet was actually using the buffer up
to its limit and if the last 64 bytes of the buffer crossed 4KB boundary
then an unmapped PCI page was accessed. The fix is to use only one
parameter for the buffer size - there is no need to differentiate
between the buffer size and the PCI mapping size since the extra 64
bytes can actually be used by the FW to align the Ethernet payload to
64 bytes.
Also updating the driver version and date
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a memory leak in an error path.
Reported-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
video_device_release() does kfree(), which made the following printk()
doing a use-after-free.
printk() first and release then.
Reported-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This adds basic support for the Hauppauge Nova-TD-500 84xxx series.
A future patch will allow for one aerial input to supply both tuners.
With the current code, an aerial must be plugged into each antannae input
in order for both tuners to function.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This comment helps to make the code more readable.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some DVB drivers are incorrectly assuming that the size of
i2c_adapter.name is I2C_NAME_SIZE. Here's a fix.
Also change strncpy to strlcpy, as the former is error-prone (and was
indeed incorrectly used.)
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Uwe Bugla <uwe.bugla@gmx.de>
Reviewed-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
1) Lower the hstart setting for all sensor by 1 so that we generate
(compressed) BGGR data just like sn9c102 does (instead of GBRG data)
2) Add support for raw bayer output in the lowest resolutions (not enough
bandwidth for higher resolutions), this should work with all sensors but
to be sure only enable it for sensors where it has been tested.
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Under certain conditions sonixb compressed frame size can get bigger then
the uncompressed size (seen with 0c45:6028), so make the buffers slightly
bigger.
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-the usb-id table caried several flags which were not usb-id specific but
sensor specific, add a sensor_data array and move these flag there
-fr_h_sz was being abused to store and check which bridge was being used
instead add a bridge member to the sd struct
-now that we have a sensor_data table use that to store pointers to
init_sequences instead of using switch cases on sd->sensor
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-remove USB-id's from zc0301 for cams for which zc0301.c does not support
the sensor
-remove USB-id's from sn9c102 for cams where sn9c102 does not support the
bridge sensor combination
-no longer make inclusion of usb id's removed from zc0301 and sn9c102
conditional in gspca
-fix conditional inclusion of USB-id's in gspca to also work when the
conflicting drivers are build as a module
-add a number of USB-id's to gspca from various windows .inf files:
0c45:608f from generic sonix sn9c103 inf file (+ ov7630 which we support)
041e:4022 from creative webcam nx pro, same as already supported 041e:401e
0ac8:0301 from generic zc0301 driver which supports many sensors
10fd:804d from typhoon webshot driver (also FlyCAM-USB 300 plus)
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The USB buffer may be used for DMA and there may be a caching problem
if the buffer is part of the device structure.
Thanks to Alan Stern.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-Add usb id for 093a:2624 (pac7302)
-Report some controls to userspace with 7302 only, as they are 7302 only
-Add gain and exposure controls
-Add autogain
-Fix 7302 imaged being mirrored by default
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- the stream must stop when the main application closes the device.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- new function 'init' called on probe and resume
- remove the functions 'open' and 'closed'
- 'stopN' and 'stop0' are optional
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- turn the led of the cam off after plugging in the cam
- move the probe code from open to config, so that if the probe fails
we never register
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- set some controls as disabled instead of copying the device descr.
- in the ov6650 / 7650 exposure code clamp reg 11 before (instead of after)
using it to calculate reg 10.
- disable brightness (instead of ignoring it) for the TAS5110.
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- documentation for some registers
- some preparations for adding autogain_n_exposure functionality
- various pac7311 fixes
- disable brightness and colors controls for 7311
- fix contrast control for 7311
- add hflip and vflip controls for 7311
- minimal jpeg header
- proper SOF detection
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I need this so I can better isolate my linux email from my
corporate email.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If apps pass QAM_AUTO then we need to obey it.
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If apps pass QAM_AUTO then we need to obey it.
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Not a bug as such, but it looks really strange doing this before
checking whether the state structure could be allocated.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
cx18: Simplify queue flush logic to prevent oops in cx18_flush_queues().
If accounting of a queue is in error, logic borrowed from ivtv will cause
an oops when flushing the queues for a stream. This change greatly
simplifies the queue flush logic, and sets the queue back to sane
defaults on a flush.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
