Add helper to deregister fixed-link PHYs registered using
of_phy_register_fixed_link().
Convert the two drivers that care to deregister their fixed-link PHYs to
use the new helper, but note that most drivers currently fail to do so.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to drop the reference taken by bus_find_device() before
returning NULL from of_phy_find_device() when the found device is not a
PHY.
Fixes: 6ed742363b ("of: of_mdio: Ensure mdio device is a PHY")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to drop the of_node reference also on failure to parse the
speed property in of_phy_register_fixed_link().
Fixes: 3be2a49e5c ("of: provide a binding for fixed link PHYs")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Abstract a general interface "of_phy_get_and_connect"
for PHY connect. User will have no bother with getting
"phy-mode" and "phy-handle" any more.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Dongpo Li <lidongpo@hisilicon.com>
Reviewed-by: Jiancheng Xue <xuejiancheng@hisilicon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calling the fixed-phy functions when CONFIG_FIXED_PHY=m as a previous
change tried cannot work if the caller is in built-in code:
drivers/of/built-in.o: In function `of_phy_register_fixed_link':
of_reserved_mem.c:(.text+0x85e0): undefined reference to `fixed_phy_register'
Making of_mdio depend on 'FIXED_PHY || !FIXED_PHY' would solve this
dependency by enforcing that OF_MDIO itself becomes a loadable module
when FIXED_PHY=y, but that creates a different dependency as it
breaks any built-in ethernet driver that uses of_mdio.
Making FIXED_PHY a bool option also cannot work, since it depends on
PHYLIB, which again is tristate.
This version now uses 'select FIXED_PHY' to ensure that the fixed-phy
portion of of_mdio is not optional. The main downside of this is
a small increase in code size for cases that do not need fixed phy
support, but it should avoid all of the link-time problems.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: d1bd330a22 ("of_mdio: Enable fixed PHY support if driver is a module")
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The fixed_phy driver doesn't have to be built-in, and it's
important that of_mdio supports it even if it's a module.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a check whether the 'struct device_node' pointer passed to
of_mdiobus_register() is an available (aka enabled) node in the Device
Tree.
Rationale for doing this are cases where an Ethernet MAC provides a MDIO
bus controller and node, and an additional Ethernet MAC might be
connecting its PHY/switches to that first MDIO bus controller, while
still embedding one internally which is therefore marked as "disabled".
Instead of sprinkling checks like these in callers of
of_mdiobus_register(), do this in a central location.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that get_phy_device() no longer returns NULL on error, we don't need
to check for it...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The results of of_mdiobus_register_{device|phy}() are never checked, so we
can make both these functions *void*...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PTR_ERR_OR_ZERO() is open coded in of_phy_register_fixed_link(), so just
call it directly...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IS_ERR_OR_NULL() is open coded in of_mdiobus_register_phy(), so just call
it directly...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mdio_device_create() never returns NULL, thus checking for it in
of_mdiobus_register_device() is pointless...
Suggested-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several cases of overlapping changes, as well as one instance
(vxlan) of a bug fix in 'net' overlapping with code movement
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
The 'flags' parameter of the of_phy_connect() function wasn't described
in the kernel-doc comment...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_mdiobus_register() declares the 'paddr' variable to hold the result of
the of_get_property() but only uses it once after that while the function
can be called directly from the *if* statement. Remove that variable and
switch to calling of_find_property() instead since we don't care about
the "reg" property's value anyway...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit ae46113196 ("of: of_mdio: Add a whitelist of PHY
compatibilities.") missed one compatible string used in in-tree DTBs:
in OCTEON, for selected boards, the kernel DTB pruning code will overwrite
the DTB compatible string with "marvell,88e1145", which is missing
from the whitelist. Add it.
The patch fixes broken networking on EdgeRouter Lite.
Fixes: ae46113196 ("of: of_mdio: Add a whitelist of PHY compatibilities.")
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some phy nodes list a compatible value indicating the PHY make/model.
This is never used to match the device to the driver. However it does
confuse the code to separate a PHY from a generic MDIO device like a
switch. Generic MDIO devices must have a compatible value, PHYs can
list clause 22 or 45, but nothing else.
Issue a warning if we find a compatible value known on the whitelist,
and say it is a PHY.
Fixes: a9049e0c51 ("mdio: Add support for mdio drivers.")
Reported-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Reported-by: Olof Johansson <olof@lixom.net>
Tested-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_phy_find_device() is used to find the phy device associated with a
device node. It is expected the node is for a PHY device, but in fact
it could of been probed as a generic MDIO device. Ensure the device is
a PHY before returning it.
Fixes: a9049e0c51 ("mdio: Add support for mdio drivers.")
Reported-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Reported-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It used to be that mdio->irq was a pointer but after e7f4dc3536
('mdio: Move allocation of interrupts into core') it's an array inside
the mdio struct so it can never be NULL.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all devices on an MDIO bus are PHYs. Meaning not all MDIO drivers
are PHY drivers. Add support for generic MDIO drivers.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than have drivers directly manipulate the mii_bus structure,
provide and API for registering and unregistering devices on an MDIO
bus, and performing lookups.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We will soon support devices other than phys on the mdio bus. Look at
a child's compatibility string to determine if it is a phy, before
registering a phy device.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all devices attached to an MDIO bus are phys. So add an
mdio_device structure to represent the generic parts of an mdio
device, and place this structure into the phy_device.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Have mdio_alloc() create the array of interrupt numbers, and
initialize it to POLLING. This is what most MDIO drivers want, so
allowing code to be removed from the drivers.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bus_find_device() is defined as:
* This is similar to the bus_for_each_dev() function above, but it
* returns a reference to a device that is 'found' for later use, as
* determined by the @match callback.
and it does indeed return a reference-counted pointer to the device:
while ((dev = next_device(&i)))
if (match(dev, data) && get_device(dev))
^^^^^^^^^^^^^^^
break;
klist_iter_exit(&i);
return dev;
What that means is that when we're done with the struct device, we must
drop that reference. Neither of_phy_connect() nor of_phy_attach() did
this when phy_connect_direct() or phy_attach_direct() failed.
With our previous patch, phy_connect_direct() and phy_attach_direct()
take a new refcount on the phy device when successful, so we can drop
our local reference immediatley after these functions, whether or not
they succeeded.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
An SFP module may have a link up/down status pin which can be
connection to a GPIO line of the host. Add support for reading such an
GPIO in the fixed_phy driver.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the PHY management type is selected by the MAC driver arbitrary.
The decision is based on the presence of the "fixed-link" node and on a
will of the driver's authors.
This caused a regression recently, when mvneta driver suddenly started
to use the in-band status for auto-negotiation on fixed links.
It appears the auto-negotiation may not work when expected by the MAC driver.
Sebastien Rannou explains:
<< Yes, I confirm that my HW does not generate an in-band status. AFAIK, it's
a PHY that aggregates 4xSGMIIs to 1xQSGMII ; the MAC side of the PHY (with
inband status) is connected to the switch through QSGMII, and in this context
we are on the media side of the PHY. >>
https://lkml.org/lkml/2015/7/10/206
This patch introduces the new string property 'managed' that allows
the user to set the management type explicitly.
The supported values are:
"auto" - default. Uses either MDIO or nothing, depending on the presence
of the fixed-link node
"in-band-status" - use in-band status
Signed-off-by: Stas Sergeev <stsp@users.sourceforge.net>
CC: Rob Herring <robh+dt@kernel.org>
CC: Pawel Moll <pawel.moll@arm.com>
CC: Mark Rutland <mark.rutland@arm.com>
CC: Ian Campbell <ijc+devicetree@hellion.org.uk>
CC: Kumar Gala <galak@codeaurora.org>
CC: Florian Fainelli <f.fainelli@gmail.com>
CC: Grant Likely <grant.likely@linaro.org>
CC: devicetree@vger.kernel.org
CC: linux-kernel@vger.kernel.org
CC: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Some Ethernet PHY devices/switches may not properly release the MDIO bus
during turn-around time, and fail to drive it low, which can be seen by
some controllers as a read failure, while the data clocked in is still
correct.
Add a boolean property "broken-turn-around" which is parsed by the
generic MDIO bus probing code and will set the corresponding bit in the
MDIO bus phy_ignore_ta_mask bitmask for MDIO bus drivers to utilize that
information.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Export of_mdio_parse_addr() which allows parsing a given Ethernet PHY
node MDIO address, verify it is within the allowed range, and return
its value. This is going to be useful for the DSA code which needs to
deal with multiple layers of MDIO buses.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adjust fixed_phy_register() to return struct phy_device *, so that
it becomes easy to use fixed PHYs without device tree support:
phydev = fixed_phy_register(PHY_POLL, &fixed_phy_status, NULL);
fixed_phy_set_link_update(phydev, fixed_phy_link_update);
phy_connect_direct(netdev, phydev, handler_fn, phy_interface);
This change is a prerequisite for modifying bcmgenet driver to work
without a device tree on Broadcom's MIPS-based 7xxx platforms.
Signed-off-by: Petri Gynther <pgynther@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit f9a8f83b04 ("net: phy: remove flags argument from phy_{attach,
connect, connect_direct}") removed the flags argument to the PHY library
calls to: phy_{attach,connect,connect_direct}.
Most Device Tree aware drivers call of_phy_connect() with the flag
argument set to 0, but some of them might want to set a different value
there in order for the PHY driver to key a specific behavior based on
the phy_device::phy_flags value.
Allow such drivers to set custom phy_flags as part of the
of_phy_connect() call since of_phy_connect() does start the PHY state
machine, it will call into the PHY driver config_init() callback which
is usually where a specific phy_flags value is important.
Fixes: f9a8f83b04 ("net: phy: remove flags argument from phy_{attach, connect, connect_direct}")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 86f6cf4127 (net: of_mdio: add of_mdiobus_link_phydev()) introduced a
circular dependency between libphy and of_mdio.
depmod: ERROR: <modroot>/kernel/drivers/net/phy/libphy.ko in
dependency cycle!
depmod: ERROR: <modroot>/kernel/drivers/of/of_mdio.ko in dependency cycle!
The problem is that of_mdio.c references &mdio_bus_type and libphy now
references of_mdiobus_link_phydev.
Fix this by not exporting of_mdiobus_link_phydev() from of_mdio.ko.
Make it a static function in mdio_bus.c instead.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reported-by: Jeff Mahoney <jeffm@suse.com>
Fixes: 86f6cf4127 (net: of_mdio: add of_mdiobus_link_phydev())
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes commit 3be2a49e5c ("of: provide a binding for fixed link PHYs")
Fix the parsing of the new fixed link dts bindings for duplex,
pause, and asym_pause by using the correct device node pointer.
Signed-off-by: Richard Retanubun <rretanubun.work@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make of_mdiobus_link_phydev externally available.
This fixes CONFIG_OF_MDIO=m.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Fixes: 86f6cf4127 ("net: of_mdio: add of_mdiobus_link_phydev()")
Signed-off-by: David S. Miller <davem@davemloft.net>
Use int rather than u32 to fix the following warning:
drivers/of/of_mdio.c:147 of_mdiobus_register() warn: unsigned 'addr' is
never less than zero.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Fixes: 8f8382888c ("net: of_mdio: factor out code to parse a phy's 'reg' property")
Signed-off-by: David S. Miller <davem@davemloft.net>
of_get_property() can be called with NULL as 2nd argument if the caller
is not interested in the length of a property. Use that here so we can
get rid of a variable.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a function to walk the list of subnodes of a mdio bus and look for
a node that matches the phy's address with its 'reg' property. If found,
set the of_node pointer for the phy. This allows auto-probed pyh
devices to be augmented by information passed in via DT.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Factor out some logic into of_mdio_parse_addr() so it can be reused
later. While at it, use of_property_read_u32() rather than open-coding
the same logic again.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit de906af1 (net: phy: make of_set_phy_supported work with genphy driver)
removed the last user of variable 'max_speed' in function
of_mdiobus_register_phy(), leading to compile warning "unused variable
‘max_speed’ [-Wunused-variable]". Thus remove it.
Signed-off-by: Christian Engelmayer <cengelma@gmx.at>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_set_phy_supported allows overwiting hardware capabilities of
a phy with values from the devicetree. of_set_phy_supported is
called right after phy_device_register in the assumption that
phy_probe is called from phy_device_register and the features
of the phy are already initialized. For the genphy driver this
is not true, here phy_probe is called later during phy_connect
time. phy_probe will then overwrite all settings done from
of_set_phy_supported
Fix this by moving of_set_phy_supported to the core phy code
and calling it from phy_probe.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
All in-tree drivers have been converted to use the new pair of
functions: of_is_fixed_phy_link() plus of_phy_register_fixed_link(), we
can now safely remove of_phy_connect_fixed_link.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some Ethernet MACs have a "fixed link", and are not connected to a
normal MDIO-managed PHY device. For those situations, a Device Tree
binding allows to describe a "fixed link" using a special PHY node.
This patch adds:
* A documentation for the fixed PHY Device Tree binding.
* An of_phy_is_fixed_link() function that an Ethernet driver can call
on its PHY phandle to find out whether it's a fixed link PHY or
not. It should typically be used to know if
of_phy_register_fixed_link() should be called.
* An of_phy_register_fixed_link() function that instantiates the
fixed PHY into the PHY subsystem, so that when the driver calls
of_phy_connect(), the PHY device associated to the OF node will be
found.
These two additional functions also support the old fixed-link Device
Tree binding used on PowerPC platforms, so that ultimately, the
network device drivers for those platforms could be converted to use
of_phy_is_fixed_link() and of_phy_register_fixed_link() instead of
of_phy_connect_fixed_link(), while keeping compatibility with their
respective Device Tree bindings.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes the generic of_mdiobus_register parse the DT compatible string for
the pattern ethernet-phy-idAAAA.BBBB. If present it should be a value that
matches the phy-id register normally readable through MDIO.
When the ID is given the phy autoprobing is defeated and the phy is
created directly.
This is necessary to support phy's that cannot be autoprobed when
of_mdiobus_register is called. Specifically, my case has the phy in reset at
of_mdiobus_register, the reset is only released once the ethernet driver
starts, before it attaches to the phy.
Tested on ARM Kirkwood with phy id 0x01410e90 (Marvell 88E1318)
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The of_mdiobus_register_phy() is not setting phy->irq thus causing
some drivers to incorrectly assume that the PHY does not have an
IRQ associated with it. Not only do some drivers report no IRQ
they do not install an interrupt handler for the PHY.
Simplify the code setting irq and set the phy->irq at the same
time so that we cover the following issues, which should cover
all the cases the code will find:
- Set phy->irq if node has irq property and mdio->irq is NULL
- Set phy->irq if node has no irq and mdio->irq is not NULL
- Leave phy->irq as PHY_POLL default if none of the above
This fixes the issue:
net eth0: attached PHY 1 (IRQ -1) to driver Micrel KSZ8041RNLI
to the correct:
net eth0: attached PHY 1 (IRQ 416) to driver Micrel KSZ8041RNLI
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 8fdade4 ("net: of_mdio: parse "max-speed" property to set PHY
supported features") introduced a typo in of_set_phy_supported for the
first assignment of phydev->supported which will not effectively limit
the PHY device supported features bits if the PHY driver contains
"higher" features (e.g: max-speed = <100> and PHY driver has
PHY_GBIT_FEATURES set).
Fix this by making sure that the very first thing is to reset to sane
defaults (PHY_BASIC_FEATURES) and then progressively add speed features
as we parse them.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
10G PHYs don't currently support running the state machine, which
is implicitly setup via of_phy_connect(). Therefore, it is necessary
to implement an OF version of phy_attach(), which does everything
except start the state machine.
Signed-off-by: Andy Fleming <afleming@gmail.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "max-speed" property is defined per the ePAPR specification to
express the maximum speed a PHY supports. Use that property, if present
to set the phydev->supported features which properly restricts the PHY
within the range of defined speeds.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If irq_of_parse_and_map fails to find an interrupt line for a given PHY,
we will force the PHY interrupt to be PHY_POLL, completely overriding
the previous value that the MDIO bus may have set for us (e.g:
PHY_IGNORE_INTERRUPT). In case of failure, just restore the previous
value.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the PHY_MAX_ADDR constant for checking if a MDIO bus address is
valid instead of using a plain "32".
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 779d835e ("net: of_mdio: scan mdiobus for PHYs without reg
property") we have two foreach loops which do pretty much the same
thing. Factor the PHY device registration in a function helper:
of_mdiobus_register_phy() which takes care of the details and allows for
future PHY specific extensions.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
