Klaus Ethgen reported occasional high CPU usages in his system that
seem caused by HD-audio driver. The perf output revealed that it's
in the unsolicited event handling in the workqueue, and the problem
seems triggered by some communication stall between the controller and
the codec at the runtime or system resume.
Actually a similar phenomenon was seen in the past for other Intel
platforms, and we already applied the workaround to enforce sync-write
for CORB/RIRB verbs for Skylake and newer chipsets (commit
2756d9143a "ALSA: hda - Fix intermittent CORB/RIRB stall on Intel
chips"). Fortunately, the same workaround is applicable to the old
chipset, and the experiment showed the positive effect.
Based on the experiment result, this patch enables the sync-write
workaround for all Intel chipsets. The only reason I hesitated to
apply this workaround was about the possibly slightly higher CPU usage.
But if the lack of sync causes a much severer problem even for quite
old chip, we should think this would be necessary for all Intel chips.
Reported-by: Klaus Ethgen <Klaus@ethgen.ch>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191223171833.GA17053@chua
Link: https://lore.kernel.org/r/20191223221816.32572-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
You can't use PCI_BASE_CLASS with pci_get_class(). This
happens to work by luck on devices with PCI_CLASS_DISPLAY_VGA, but
misses PCI_CLASS_DISPLAY_OTHER. Add a check for those as well.
Fixes: 586bc4aab8 ("ALSA: hda/hdmi - fix vgaswitcheroo detection for AMD")
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Link: https://lore.kernel.org/r/20191221001702.1338587-1-alexander.deucher@amd.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Make sure to check the return value of usb_altnum_to_altsetting() to
avoid dereferencing a NULL pointer when the requested alternate settings
is missing.
The format altsetting number may come from a quirk table and there does
not seem to be any other validation of it (the corresponding index is
checked however).
Fixes: b099b9693d ("ALSA: usb-audio: Avoid superfluous usb_set_interface() calls")
Cc: stable <stable@vger.kernel.org> # 4.18
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191220093134.1248-1-johan@kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Recently we found the headset-mic on the Dell Dock WD19 doesn't work
anymore after s3 (s2i or deep), this problem could be workarounded by
closing (pcm_close) the app and then reopening (pcm_open) the app, so
this bug is not easy to be detected by users.
When problem happens, retire_capture_urb() could still be called
periodically, but the size of captured data is always 0, it could be
a firmware bug on the dock. Anyway I found after resuming, the
snd_usb_pcm_prepare() will be called, and if we forcibly run
set_format() to set the interface and its endpoint, the capture
size will be normal again. This problem and workaound also apply to
playback.
To fix it in the kernel, add a quirk to let set_format() run
forcibly once after resume.
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191218132650.6303-1-hui.wang@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A collection of fixes since the merge window, mostly driver specific but
there's a few in the core that clean up fallout from the refactorings
done in the last cycle.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl34w3ITHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0FM/B/9zM8zae1DIXi10S7tRElz/LnadE7il
umQ34PoghSd/f9D5TCQZMgyLjdglyQGiOar4G1xkOEC87yjBCY8AOfcV3QQLRsgK
ej8AdrBGKQUWvCdoJGx/FsrwTpgBcvRNvVJbHIKab2BfGxZA8t733tMCAkuXHnty
/dtYhA5wjI6gGtUofihEp9jvVuRLWFjopaUJs4JANKO5pmRfXgzdayt74xUKz2/q
VQCp2dCmCSXSIyYUwoY/Dg9+3RQ6Ebt3YfSWBGUrxyW+EyYtCGz4lHzV3Wb+QThM
daV+wHXlz0vW4Zr6rUz6D6WlyiK9IlhEX+hdYJagFnHmKXNcpHHl2LvU
=sP7K
-----END PGP SIGNATURE-----
Merge tag 'asoc-fix-v5.5-rc2' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v5.5
A collection of fixes since the merge window, mostly driver specific but
there's a few in the core that clean up fallout from the refactorings
done in the last cycle.
We made the error message for the CORB/RIRB communication clearer by
upgrading to dev_WARN() so that user can notice better. But this
struck us like a boomerang: now it caught syzbot and reported back as
a fatal issue although it's not really any too serious bug that worth
for stopping the whole system.
OK, OK, let's be softy, downgrade it to the standard dev_err() again.
Fixes: dd65f7e19c ("ALSA: hda - Show the fatal CORB/RIRB error more clearly")
Reported-by: syzbot+b3028ac3933f5c466389@syzkaller.appspotmail.com
Link: https://lore.kernel.org/r/20191216151224.30013-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
According to user manual, it is required that FLL_LAMBDA > 0
in all cases (Integer and Franctional modes).
Fixes: 9a76f1ff6e ("ASoC: Add initial WM8962 CODEC driver")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/1576065442-19763-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The commit e38e486d66 ("ALSA: hda: Modify stream stripe mask only
when needed") tried to address the regression by the unconditional
application of the stripe mask, but this caused yet another
regression for the previously working devices. Namely, the patch
clears the azx_dev->stripe flag at snd_hdac_stream_clear(), but this
may be called multiple times before restarting the stream, so this
ended up with clearance of the flag for the whole time.
This patch fixes the regression by moving the azx_dev->stripe flag
clearance at the counter-part, the close callback of HDMI codec
driver instead.
Fixes: e38e486d66 ("ALSA: hda: Modify stream stripe mask only when needed")
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=205855
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=204477
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191214175217.31852-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
CA0132 has the delayed HP jack detection code that is invoked from the
unsol handler, but it does a few weird things: it contains the cancel
of a work inside the work handler, and yet it misses the cancel-sync
call at (runtime-)suspend. This patch addresses those issues.
Fixes: 15c2b3cc09 ("ALSA: hda/ca0132 - Fix possible workqueue stall")
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191213085111.22855-4-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Introduce a timeout to dspio_clear_response_queue() so that it won't
be caught in an endless loop even if the hardware doesn't respond
properly.
Fixes: a73d511c48 ("ALSA: hda/ca0132: Add unsol handler for DSP and jack detection")
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191213085111.22855-3-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We need to keep power on while processing the DSP response via unsol
event. Each snd_hda_codec_read() call does the power management, so
it should work normally, but still it's safer to keep the power up for
the whole function.
Fixes: a73d511c48 ("ALSA: hda/ca0132: Add unsol handler for DSP and jack detection")
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191213085111.22855-2-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The current PCM code doesn't initialize explicitly the buffers
allocated for PCM streams, hence it might leak some uninitialized
kernel data or previous stream contents by mmapping or reading the
buffer before actually starting the stream.
Since this is a common problem, this patch simply adds the clearance
of the buffer data at hw_params callback. Although this does only
zero-clear no matter which format is used, which doesn't mean the
silence for some formats, but it should be OK because the intention is
just to clear the previous data on the buffer.
Reported-by: Lionel Koenig <lionel.koenig@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191211155742.3213-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
After applying the fixup ALC274_FIXUP_DELL_AIO_LINEOUT_VERB, the
Line-out jack works well. And instead of adding a new set of pin
definition in the pin_fixup_tbl, we put a more generic matching entry
in the fallback_pin_fixup_tbl.
Cc: <stable@vger.kernel.org>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Link: https://lore.kernel.org/r/20191211051321.5883-1-hui.wang@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Nicholas Johnson reports a null pointer deref as well as a refcount
underflow upon hot-removal of a Thunderbolt-attached AMD eGPU.
He's bisected the issue down to commit 586bc4aab8 ("ALSA: hda/hdmi -
fix vgaswitcheroo detection for AMD").
The commit iterates over PCI devices using pci_get_class() and
unreferences each device found, even though pci_get_class()
subsequently unreferences the device as well. Fix it.
Fixes: 586bc4aab8 ("ALSA: hda/hdmi - fix vgaswitcheroo detection for AMD")
Link: https://lore.kernel.org/r/PSXP216MB0438BFEAA0617283A834E11580580@PSXP216MB0438.KORP216.PROD.OUTLOOK.COM/
Reported-and-tested-by: Nicholas Johnson <nicholas.johnson-opensource@outlook.com.au>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Alexander Deucher <alexander.deucher@amd.com>
Cc: Bjorn Helgaas <helgaas@kernel.org>
Link: https://lore.kernel.org/r/77aa6c01aefe1ebc4004e87b0bc714f2759f15c4.1575985006.git.lukas@wunner.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On CML boards with the RT5682 headset codec and RT1011 speaker
amplifier, the platform firmware exposes three ACPI HIDs
(10EC5682, 10EC1011 and MX98357A). The last HID is a mistake in
DSDT tables, which causes the wrong machine driver to be loaded.
This patch changes the key used to identify boards and changes the
order of entries in the table to load the correct machine driver.
The order does matter and should not be modified to work-around this
firmware issue.
Signed-off-by: Amery Song <chao.song@intel.com>
Signed-off-by: Keyon Jie <yang.jie@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191210004854.16845-9-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Turns out SSP 3-5 are only available on cht, to avoid dumping on
undefined registers let's split the definition.
Signed-off-by: Curtis Malainey <cujomalainey@chromium.org>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191210004854.16845-7-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
An error occurs during parsing more than one ext_data from the mailbox, because
of invalid data offset handling. Fix by removing the incorrect duplicate
increment of the offset.
The return value is also reset in the switch case. This does not change the
behavior but improves readability - there is no longer a need to check what the
return value of get_ext_windows is.
Signed-off-by: Karol Trzcinski <karolx.trzcinski@linux.intel.com>
Signed-off-by: Bartosz Kokoszko <bartoszx.kokoszko@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191210004854.16845-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Added warning log when found some unknown FW boot ext header,
to improve debuggability.
Signed-off-by: Karol Trzcinski <karolx.trzcinski@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191210004854.16845-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In normal sound case all DAIs are detected as CPU-Codec.
simple_dai_link_of supports the presence of a platform but it counts
it as a CPU DAI resulting in the creation of an extra link.
Adding a platform property to a link description like:
simple-audio-card,dai-link {
cpu {
sound-dai = <&sai1>;
};
plat {
sound-dai = <&dsp>;
};
codec {
sound-dai = <&wm8960>;
}
will result in the creation of two links:
* sai1 <-> wm8960
* dsp <-> wm8960
which is obviously not what we want. We just want one single link
with:
* sai1 <-> wm8960 (and platform set to dsp).
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/20191209135353.17427-1-daniel.baluta@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The return value of soc_tplg_pcm_create() is currently not checked
in soc_tplg_pcm_elems_load(). If an error is to occur there, the
topology ignores it and continues loading.
Fix that by checking the status and rejecting the topology on error.
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Dragos Tarcatu <dragos_tarcatu@mentor.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191210003939.15752-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
snd_soc_add_dai_link() might fail. This situation occurs for
instance in a very specific use case where a PCM device and a
Back End DAI link are given identical names in the topology.
When this happens, soc_new_pcm_runtime() fails and then
snd_soc_add_dai_link() returns -ENOMEM when called from
soc_tplg_fe_link_create(). Because of that, the link will not
get added into the card list, so any attempt to remove it later
ends up in a panic.
Fix that by checking the return status and free the memory in case
of an error.
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Dragos Tarcatu <dragos_tarcatu@mentor.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191210003939.15752-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There are many paths to soc_free_pcm_runtime which can both have and
have not yet inited the workqueue yet. When we flush the queue when we
have not yet inited the queue we cause warnings to be printed.
An example is soc_cleanup_card_resources which is called by
snd_soc_bind_card which has multiple failure points before and after
soc_link_init -> soc_new_pcm which is where the queue is inited.
Signed-off-by: Curtis Malainey <cujomalainey@chromium.org>
Link: https://lore.kernel.org/r/20191128011358.39234-1-cujomalainey@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Mutex is doubly unlocked in some error path of pcm.open. This commit fixes
ALSA firewire-motu driver in Linux kernel v5.5.
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: 3fd80b2003 ("ALSA: firewire-motu: use the same size of period for PCM substream in AMDTP streams")
Fixes: 0f5482e787 ("ALSA: firewire-motu: share PCM buffer size for both direction")
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20191208232226.6685-1-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The loop optimizer seems to go astray here, and produces some warnings
that don't seem valid.
Still, the code can be simplified -- just clear the whole array at the
beginning, and fill in whatever values are valid on the platform.
Warnings before this change (GCC 8.2.0 ARM allmodconfig):
In file included from ../sound/pci/echoaudio/gina24.c:115:
../sound/pci/echoaudio/echoaudio.c: In function 'snd_echo_vumeters_get':
../sound/pci/echoaudio/echoaudio_dsp.c:647:9: warning: iteration 1073741824 invokes undefined behavior [-Waggressive-loop-optimizations]
In file included from ../sound/pci/echoaudio/layla24.c:112:
../sound/pci/echoaudio/echoaudio.c: In function 'snd_echo_vumeters_get':
../sound/pci/echoaudio/echoaudio_dsp.c:658:9: warning: iteration 1073741824 invokes undefined behavior [-Waggressive-loop-optimizations]
../sound/pci/echoaudio/echoaudio_dsp.c:647:9: warning: iteration 1073741824 invokes undefined behavior [-Waggressive-loop-optimizations]
Signed-off-by: Olof Johansson <olof@lixom.net>
Link: https://lore.kernel.org/r/20191207224953.25944-1-olof@lixom.net
Signed-off-by: Takashi Iwai <tiwai@suse.de>
syzkaller reported an invalid access in PCM OSS read, and this seems
to be an overflow of the internal buffer allocated for a plugin.
Since the rate plugin adjusts its transfer size dynamically, the
calculation for the chained plugin might be bigger than the given
buffer size in some extreme cases, which lead to such an buffer
overflow as caught by KASAN.
Fix it by limiting the max transfer size properly by checking against
the destination size in each plugin transfer callback.
Reported-by: syzbot+f153bde47a62e0b05f83@syzkaller.appspotmail.com
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191204144824.17801-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When the Teclast X89 quirk was added we did not have jack-detection
support yet.
Note the over-current detection limit is set to 2mA instead of the usual
1.5mA because this tablet tends to give false-positive button-presses
when it is set to 1.5mA.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191203221442.2657-1-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There are cases where we fail before we reach soc_new_pcm which would
init the workqueue. When we fail we attempt to flush the queue which
generates warnings from the workqueue subsystem when we have not inited
the queue. Solution is to use a proxy function to get around this issue.
Signed-off-by: Curtis Malainey <cujomalainey@chromium.org>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20191203173007.46504-1-cujomalainey@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The commit 609f548534 ("ALSA: hda: hdmi - preserve non-MST PCM
routing for Intel platforms") tried to restore the old behavior wrt
assignment of the PCM slot for Intel platforms, but this didn't do it
right. As found in the later discussion, a positive pipe id on Intel
platforms can be passed for single monitor attachment case.
This patch reverts the previous attempt and applies a simpler
workaround instead. Actually, for Intel platforms, we can handle as
if per_pin->dev_id=0, assign the primary slot at the first try. This
assures the compatible behavior with the previous versions regarding
the slot assignment.
Fixes: 609f548534 ("ALSA: hda: hdmi - preserve non-MST PCM routing for Intel platforms")
Link: https://lore.kernel.org/r/20191203154105.30414-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix build error:
sound/soc/intel/atom/sst/sst.c: In function intel_sst_interrupt_mrfld:
sound/soc/intel/atom/sst/sst.c:93:5: error: implicit declaration of function memcpy_fromio;
did you mean memcpy32_fromio? [-Werror=implicit-function-declaration]
memcpy_fromio(msg->mailbox_data,
^~~~~~~~~~~~~
memcpy32_fromio
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191128135853.8360-1-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The recent commit in HD-audio stream management for changing the
stripe control seems causing a regression on some platforms. The
stripe control is currently used only by HDMI codec, and applying the
stripe mask unconditionally may lead to scratchy and static noises as
seen on some MacBooks.
For addressing the regression, this patch changes the stream
management code to apply the stripe mask conditionally only when the
codec driver requested.
Fixes: 9b6f7e7a29 ("ALSA: hda: program stripe bits for controller")
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=204477
Tested-by: Michael Pobega <mpobega@neverware.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191202074947.1617-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The auto-parser assigns the bass speaker to DAC3 (NID 0x06) which
is without the volume control. I do not see a reason to use DAC2,
because the shared output to all speakers produces the sufficient
and well balanced sound. The stereo support is enough for this
purpose (laptop).
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20191129144027.14765-1-perex@perex.cz
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit 5398e94fb7 ("ALSA: hda - Add DP-MST support for NVIDIA codecs")
introduced a slight change of behaviour how non-MST monitors are
assigned to PCMs on Intel platforms.
In the drm_audio_component.h interface, the third parameter
to pin_eld_notify() is pipe number. On Intel platforms, this value
is -1 for MST. On other platforms, a non-zero pipe id is used to
signal MST use.
This difference leads to some subtle differences in hdmi_find_pcm_slot()
with regards to how non-MST monitors are assigned to PCMs.
This patch restores the original behaviour on Intel platforms while
keeping the new allocation policy on other platforms.
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20191129143756.23941-2-kai.vehmanen@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add additional check in hdmi_find_pcm_slot() to not return
a pcm index that points to unallocated pcm. This could happen
if codec driver is set up in codec->mst_no_extra_pcms mode.
On some platforms, this leads to a kernel oops in snd_ctl_notify(),
called via update_eld().
BugLink: https://github.com/thesofproject/linux/issues/1536
Fixes: 5398e94fb7 ALSA: hda - Add DP-MST support for NVIDIA codecs
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20191129143756.23941-1-kai.vehmanen@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We've added the bass speaker support on Acer 8951G by the commit
00066e9733 ("Add Acer Aspire Ethos 8951G model quirk"), but it seems
that the GPIO pin was wrongly set: while the commit turns off the bit
to power up the amp, the actual hardware reacts other way round,
i.e. GPIO bit on = amp on.
So this patch fixes the bug, turning on the GPIO bit 0x02 as default.
Since turning on the GPIO bit can be more easily managed with
alc_setup_gpio() call, we simplify the quirk code by integrating the
GPIO setup into the existing alc662_fixup_aspire_ethos_hp() and
dropping the whole ALC669_FIXUP_ACER_ASPIRE_ETHOS_SUBWOOFER quirk.
Fixes: 00066e9733 ("Add Acer Aspire Ethos 8951G model quirk")
Reported-and-tested-by: Sergey 'Jin' Bostandzhyan <jin@mediatomb.cc>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191128202630.6626-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
headphone have noise even the volume is very small.
Let it fill up pcbeep hidden register to default value.
The issue was gone.
Fixes: 4344aec84b ("ALSA: hda/realtek - New codec support for ALC256")
Fixes: 736f20a706 ("ALSA: hda/realtek - Add support for ALC236/ALC3204")
Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/9ae47f23a64d4e41a9c81e263cd8a250@realtek.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix regression in how intel_haswell_fixup_connect_list()
results are used in hda_read_pin_conn(). Use of
snd_hda_get_raw_connections() in hda_read_pin_conn() bypasses
the cache and thus also bypasses the overridden pin connection
list. On platforms that require the connection list fixup,
mux list will be empty and HDMI playback will fail to -EBUSY
at open.
Fix the regression in hda_read_pinn_conn(). Simplify code
as suggested by Takashi Iwai to remove old
intel_haswell_fixup_connect_list() and copy the cvt_nid list
directly and not use snd_hda_override_conn_list() at all.
Fixes: 9c32fea836 ("ALSA: hda - Add DP-MST support for non-acomp codecs")
BugLink: https://github.com/thesofproject/linux/issues/1537
Cc: Nikhil Mahale <nmahale@nvidia.com>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20191127161240.17026-1-kai.vehmanen@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
max98090_interrupt() and max98090_pll_work() run in 2 different threads.
There are 2 possible races:
Note: M98090_REG_DEVICE_STATUS = 0x01.
Note: ULK == 0, PLL is locked; ULK == 1, PLL is unlocked.
max98090_interrupt max98090_pll_work
----------------------------------------------
schedule max98090_pll_work
restart max98090 codec
receive ULK INT
assert ULK == 0
schedule max98090_pll_work (1).
In the case (1), the PLL is locked but max98090_interrupt unnecessarily
schedules another max98090_pll_work.
max98090_interrupt max98090_pll_work max98090 codec
----------------------------------------------------------------------
ULK = 1
receive ULK INT
read 0x01
ULK = 0 (clear on read)
schedule max98090_pll_work
restart max98090 codec
ULK = 1
receive ULK INT
read 0x01
ULK = 0 (clear on read)
read 0x01
assert ULK == 0 (2).
In the case (2), both max98090_interrupt and max98090_pll_work read
the same clear-on-read register. max98090_pll_work would falsely
thought PLL is locked.
Note: the case (2) race is introduced by the previous commit ("ASoC:
max98090: exit workaround earlier if PLL is locked") to check the status
and exit the loop earlier in max98090_pll_work.
There are 2 possible solution options:
A. turn off ULK interrupt before scheduling max98090_pll_work; and turn
on again before exiting max98090_pll_work.
B. remove the second thread of execution.
Option A cannot fix the case (2) race because it still has 2 threads
access the same clear-on-read register simultaneously. Although we
could suppose the register is volatile and read the status via I2C could
be much slower than the hardware raises the bits.
Option B introduces a maximum 10~12 msec penalty delay in the interrupt
handler. However, it could only punish the jack detection by extra
10~12 msec.
Adopts option B which is the better solution overall.
Signed-off-by: Tzung-Bi Shih <tzungbi@google.com>
Link: https://lore.kernel.org/r/20191122073114.219945-4-tzungbi@google.com
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
According to the datasheet, PLL lock time typically takes 2 msec and
at most takes 7 msec.
Check the lock status every 1 msec and exit the workaround if PLL is
locked.
Signed-off-by: Tzung-Bi Shih <tzungbi@google.com>
Link: https://lore.kernel.org/r/20191122073114.219945-3-tzungbi@google.com
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It was observed Baytrail-based chromebooks could cause continuous PLL
unlocked when using playback stream and capture stream simultaneously.
Specifically, starting a capture stream after started a playback stream.
As a result, the audio data could corrupt or turn completely silent.
As the datasheet suggested, the maximum PLL lock time should be 7 msec.
The workaround resets the codec softly by toggling SHDN off and on if
PLL failed to lock for 10 msec. Notably, there is no suggested hold
time for SHDN off.
On Baytrail-based chromebooks, it would easily happen continuous PLL
unlocked if there is a 10 msec delay between SHDN off and on. Removes
the msleep().
Signed-off-by: Tzung-Bi Shih <tzungbi@google.com>
Link: https://lore.kernel.org/r/20191122073114.219945-2-tzungbi@google.com
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The simple-card tries to signal the codec to disable rate constraints,
see commit 2458adb8f9 ("SoC: simple-card-utils: set 0Hz to sysclk when
shutdown"). This wasn't handled by the codec, instead it would set the
FLL frequency to 0Hz which isn't working. Since we don't have any rate
constraints just ignore this request.
Fixes: 13409d27cb ("ASoC: wm8904: configure sysclk/FLL automatically")
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20191122232532.22258-1-michael@walle.cc
Signed-off-by: Mark Brown <broonie@kernel.org>
If CONFIG_SPI is n, SND_SOC_RT5677_SPI also is n, building fails:
sound/soc/codecs/rt5677.o: In function `rt5677_irq':
rt5677.c:(.text+0x2dbf): undefined reference to `rt5677_spi_hotword_detected'
sound/soc/codecs/rt5677.o: In function `rt5677_dsp_work':
rt5677.c:(.text+0x3709): undefined reference to `rt5677_spi_write'
This adds stub helpers to fix this.
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 461c623270 ("ASoC: rt5677: Load firmware via SPI using delayed work")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20191127082145.6100-1-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Link unload now fails for ESAI/SAI DAIs with:
"error: invalid DAI type 6" because DAI type is not
properly handled.
Fix this by correctly handling cases where type is ESAI or SAI.
Fixes: a4eff5f86c ("ASoC: SOF: imx: Read ESAI parameters and send them to DSP")
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191126141606.21650-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The shim registers in BYT/CHT/BSW are 64bits based, correct the
copy/paste (from bdw.c where the shim registers are 32bits based) error
in byt_dump().
Fixes: 3a9e204d4e ("ASoC: SOF: Intel: Add context data to any IPC timeout")
Signed-off-by: Keyon Jie <yang.jie@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20191126141533.21601-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Some usages only call startup and shutdown without setting hw_params
(e.g. arecord --dump-hw-params). If we don't enable clk in startup, it
will cause ref count error because the clk will be disabled in shutdown.
For this reason, we should move enabling clk from hw_params to startup.
In addition, the hw_params is fixed in this driver(48000 rate, 2
channels, S16_LE format) so we don't need to change the clk rate after
the hw_params is set.
Signed-off-by: Yu-Hsuan Hsu <yuhsuan@chromium.org>
Acked-by: Akshu Agrawal <akshu.agarawal@amd.com>
Link: https://lore.kernel.org/r/20191126075424.80668-1-yuhsuan@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Static analysis tools (cppcheck and PVS Studio) report an error
in loopback_snd_timer_period_elapsed() regarding dpcm_play pointer
dereference earlier than its null-check. And although this is a result
of a formal check, and the pointer correctness is also protected
by having a corresponding bit set in the "running" mask, re-ordering
of the lines can imake the code even formally correct and eliminate
those static analysis error reports.
Fixes: 26c53379f9 ("ALSA: aloop: Support selection of snd_timer instead of jiffies")
Reported-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Link: https://lore.kernel.org/r/20191127110622.26105-1-andrew_gabbasov@mentor.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
So that we can power down the GPU and audio to save power.
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Link: https://lore.kernel.org/r/20191122214353.582899-5-alexander.deucher@amd.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We are able to power down the GPU and audio via the GPU driver
so flag these asics as supporting runtime pm.
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Link: https://lore.kernel.org/r/20191122214353.582899-4-alexander.deucher@amd.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
