Remove double underscore prefix from numeric types. This code will never be used
outside the kernel so the prefixes are unnecessary.
Signed-off-by: Michal Malý <madcatxster@devoid-pointer.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This reverts commit 3a61e97563.
The Logitech TK820 seems to be affected by a firmware bug which
delays the sending of the keys (pressed, or released, which triggers
a key-repeat) while holding fingers on the touch sensor.
This behavior can be observed while using the mouse emulation mode
if the user moves the finger while typing (highly improbable though).
Holding the finger still while in the mouse emulation mode does
not trigger the key repeat problem.
So better keep things in their previous state to not have to
explain users that the new key-repeat bug they see is a "feature".
Furthermore, I noticed that I disabled the media keys whith
this patch. Sorry, my bad.
I think it is best to revert the patch, in all the current
versions it has been shipped.
Cc: <stable@vger.kernel.org> # v3.19 and above
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Correct a spelling mistake in the Sixaxis HID descriptor comment.
Add an explanation as to why the Sixaxis has so many analog axes and why
some of them are seen as multi-touch axes.
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Directly set the initial LED states in the device state struct instead
of copying them from a temporary array.
This allows for the removal of a redundant "x = x" copy loop in
sony_set_leds() that was taking place any time an LED was updated.
It also allows for the simplifying of the parameters in functions dealing
with LED initialization and updates since only a pointer to the sony_sc
struct is needed now.
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Rearrange Sony controller devices into alphabetical order in the hardware
device list.
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add a fixed-up HID descriptor for the Sony motion controller and enable
controls for the LED light as well as force-feedback.
The LED is multi-colored (red, green, blue).
The motion controller has a single rumble motor so the higher of the left
and right values is used to set the speed.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Adds the PID for the Sony motion controller to the hardware ID list.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
sony_allocate_output_report() was being called before sony_set_device_id()
which meant that an unallocated ida value was was freed if the output
report allocation failed and the probe function jumped to err_stop.
Do the device ID allocation before the output report allocation to avoid
freeing an unallocated value in case of a failure.
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
'key' is set but never used in the first loop. So remove the set.
And indent the re-set of pm->last_key properly.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
wait_event_interruptible_timeout() expects a timeout in jiffies so the
numeric constant becomes HZ dependent - put it through msecs_to_jiffies()
to make it HZ independent.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This dock is used with the Thinkpad Helix 2 but suffers from an error
in the report descriptor where an usage max is 65535.
Add a report fixup for it and make the keyboard working.
Tested-by: Jonathan Oppenheim <lejono@gmail.com>
Tested-by: John Reid <owlman.lists@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The last patch was careful to maintain backwards-compatible behavior
by forcing device_type to BTN_TOOL_PEN (and printing a warning) if it
were still uninitialized after scanning the HID descriptor and applying
quirks. We should be more strict with HID_GENERIC devices, however,
since there is no a priori guarantee that it is a tablet or touchpad.
If the device_type is still uninitialized for a HID_GENERIC device then
we assume that it isn't something the driver can work with and so fail
the probe.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Currently, we assume a device_type of BTN_TOOL_PEN before scanning the
HID descriptor and then change the device_type if what we discover
proves that assumption wrong. This way of doing things makes it more
difficult to figure out if a device (particularly a HID_GENERIC device)
actually does tablet/touch input or is something completley different.
This patch leaves device_type at its initial value of 0 and then calls
'wacom_parse_hid' for every device (not just those that have touch).
As we map the usages, we can set the device_type as before. After we're
finished, we can then check if the value is still zero and do whatever
is most appropriate.
Detecting the pen can be a little tricky on most Wacom devices because
the descriptors describe opaque blobs. Fortunately, older Wacom tablets
have the HID_DG_DIGITIZER usage on the pen's application collection and
newer tablets seem to have a similar vendor-defined usage that we can
trigger on.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The naming logic currently assumes that all devices will be a pen, finger,
or pad. Though this has historically been the case, the new HID_GENERIC
catch-all may cause us to probe devices with Wacom's 056A VID which aren't
any of these types (e.g. the "Cintiq 24HDT Monitor Control"). This patch
updates the logic so that no suffix will be added to the device name if
the device type is unknown.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
HID generic devices share the same default name, "Wacom HID". This
causes userland programs to show same device names for different
devices, which would confuse end users with same device names for
different devices too.
This patch uses name retrieved from HID descriptor, if a meaningful
name is reported. Otherwise, affix its product ID to "Wacom HID".
Names from descriptor may contain extra whitespaces. To comfort
readers' eyes, we removed those extra whitespaces too.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The raphnet.net 4nes4snes and 2nes2snes multi-joystick adapters use a single
HID report descriptor with one report ID per controller. This has the effect
that the inputs of otherwise independent game controllers get packed in one
large joystick device.
With this patch each controller gets its own /dev/input/jsX device, which is
more natural and less confusing than having all inputs going to the same place.
Signed-off-by: Raphael Assenat <raph@raphnet.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Using GPIOs and gpiolib is optional. If the kernel is compiled without GPIO
support the driver should not fail if it finds the interrupt using normal
methods.
However, commit a485923efb ("HID: i2c-hid: Add support for ACPI GPIO
interrupts") did not take into account that acpi_dev_add_driver_gpios()
returns -ENXIO when !CONFIG_GPIOLIB.
Fix this by checking the return value against -ENXIO and 0 and only in that
case fail the probe.
Reported-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Set flags INPUT_PROP_POINTER and INPUT_PROP_POINTING_STICK for the trackpoint
integrated in Lenovo USB and Bluetooth keyboards. Libinput checks these flags
to enable features such as middle-button-scrolling by default.
Signed-off-by: Andreas Fleig <andreasfleig@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
To determine if a touch is present in the single-touch case, we can
simply check if the BTN_TOUCH key is active or not. This will work for
both HID_GENERIC and other device types.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
We use generic hid_report_len() to get individual packet length now.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
That is where they belong...
Signed-off-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
It makes probe routine easy to follow.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Pull input subsystem updates from Dmitry Torokhov:
"You will get the following new drivers:
- Qualcomm PM8941 power key drver
- ChipOne icn8318 touchscreen controller driver
- Broadcom iProc touchscreen and keypad drivers
- Semtech SX8654 I2C touchscreen controller driver
ALPS driver now supports newer SS4 devices; Elantech got a fix that
should make it work on some ASUS laptops; and a slew of other
enhancements and random fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (51 commits)
Input: alps - non interleaved V2 dualpoint has separate stick button bits
Input: alps - fix touchpad buttons getting stuck when used with trackpoint
Input: atkbd - document "no new force-release quirks" policy
Input: ALPS - make alps_get_pkt_id_ss4_v2() and others static
Input: ALPS - V7 devices can report 5-finger taps
Input: ALPS - add support for SS4 touchpad devices
Input: ALPS - refactor alps_set_abs_params_mt()
Input: elantech - fix absolute mode setting on some ASUS laptops
Input: atmel_mxt_ts - split out touchpad initialisation logic
Input: atmel_mxt_ts - implement support for T100 touch object
Input: cros_ec_keyb - fix clearing keyboard state on wakeup
Input: gscps2 - drop pci_ids dependency
Input: synaptics - allocate 3 slots to keep stability in image sensors
Input: Revert "Revert "synaptics - use dmax in input_mt_assign_slots""
Input: MT - make slot assignment work for overcovered solutions
mfd: tc3589x: enforce device-tree only mode
Input: tc3589x - localize platform data
Input: tsc2007 - Convert msecs to jiffies only once
Input: edt-ft5x06 - remove EV_SYN event report
Input: edt-ft5x06 - allow to setting the maximum axes value through the DT
...
Pull HID updates from Jiri Kosina:
- quite a few firmware fixes for RMI driver by Andrew Duggan
- huion and uclogic drivers have been substantially overlaping in
functionality laterly. This redundancy is fixed by hid-huion driver
being merged into hid-uclogic; work done by Benjamin Tissoires and
Nikolai Kondrashov
- i2c-hid now supports ACPI GPIO interrupts; patch from Mika Westerberg
- Some of the quirks, that got separated into individual drivers, have
historically had EXPERT dependency. As HID subsystem matured (as
well as the individual drivers), this made less and less sense. This
dependency is now being removed by patch from Jean Delvare
- Logitech lg4ff driver received a couple of improvements for mode
switching, by Michal Malý
- multitouch driver now supports clickpads, patches by Benjamin
Tissoires and Seth Forshee
- hid-sensor framework received a substantial update; namely support
for Custom and Generic pages is being added; work done by Srinivas
Pandruvada
- wacom driver received substantial update; it now supports
i2c-conntected devices (Mika Westerberg), Bamboo PADs are now
properly supported (Benjamin Tissoires), much improved battery
reporting (Jason Gerecke) and pen proximity cleanups (Ping Cheng)
- small assorted fixes and device ID additions
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (68 commits)
HID: sensor: Update document for custom sensor
HID: sensor: Custom and Generic sensor support
HID: debug: fix error handling in hid_debug_events_read()
Input - mt: Fix input_mt_get_slot_by_key
HID: logitech-hidpp: fix error return code
HID: wacom: Add support for Cintiq 13HD Touch
HID: logitech-hidpp: add a module parameter to keep firmware gestures
HID: usbhid: yet another mouse with ALWAYS_POLL
HID: usbhid: more mice with ALWAYS_POLL
HID: wacom: set stylus_in_proximity before checking touch_down
HID: wacom: use wacom_wac_finger_count_touches to set touch_down
HID: wacom: remove hardcoded WACOM_QUIRK_MULTI_INPUT
HID: pidff: effect can't be NULL
HID: add quirk for PIXART OEM mouse used by HP
HID: add HP OEM mouse to quirk ALWAYS_POLL
HID: wacom: ask for a in-prox report when it was missed
HID: hid-sensor-hub: Fix sparse warning
HID: hid-sensor-hub: fix attribute read for logical usage id
HID: plantronics: fix Kconfig default
HID: pidff: support more than one concurrent effect
...
* new API for safe access of power supply function attrs
* devres support for power supply (un)registration
* new drivers / chips
- generic syscon based poweroff driver
- iio & charger driver for da9150
- fuel gauge driver for axp288
- bq27x00: add support for bq27510
- bq2415x: add support for bq24157s
* twl4030-madc-battery: convert to iio consumer
* misc fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=WbZu
-----END PGP SIGNATURE-----
Merge tag 'for-v4.1' of git://git.infradead.org/battery-2.6
Pull power supply and reset changes from Sebastian Reichel:
- new API for safe access of power supply function attrs
- devres support for power supply (un)registration
- new drivers / chips:
- generic syscon based poweroff driver
- iio & charger driver for da9150
- fuel gauge driver for axp288
- bq27x00: add support for bq27510
- bq2415x: add support for bq24157s
- twl4030-madc-battery: convert to iio consumer
- misc fixes
* tag 'for-v4.1' of git://git.infradead.org/battery-2.6: (66 commits)
power: twl4030_madc_battery: Add missing MODULE_ALIAS
power: twl4030-madc-battery: Convert to iio consumer.
dt: power: Add docs for generic SYSCON poweroff driver.
power: reset: Add generic SYSCON register mapped poweroff.
power: max17042_battery: add missed blank
power: max17042_battery: Use reg type instead of chip type
power/reset: at91: big endian fixes for atsama5d3x
power_supply: charger-manager: Fix dereferencing of ERR_PTR
HID: input: Fix NULL pointer dereference when power_supply_register fails
power: constify of_device_id array
power/reset/rmobile-reset.c: Fix !HAS_IOMEM build
power_supply: 88pm860x_charger: Fix possible NULL pointer dereference and use of initialized variable
arm: mach-pxa: Decrement the power supply's device reference counter
mfd: ab8500: Decrement the power supply's device reference counter
power_supply: bq2415x_charger: Decrement the power supply's device reference counter
power_supply: 88pm860x_charger: Decrement the power supply's device reference counter
x86/olpc/xo15/sci: Use newly added power_supply_put API
x86/olpc/xo1/sci: Use newly added power_supply_put API
power_supply: charger-manager: Decrement the power supply's device reference counter
power_supply: Increment power supply use counter when obtaining references
...
HID Sensor Spec defines two usage ids for custom sensors
HID_USAGE_SENSOR_TYPE_OTHER_CUSTOM (0x09, 0xE1)
HID_USAGE_SENSOR_TYPE_OTHER_GENERIC(0x09, 0xE2)
In addition the standard also defines usage ids for custom fields.
The purpose of these sensors is to extend the functionality or provide a way to
obfuscate the data being communicated by a sensor. Without knowing the mapping
between the data and its encapsulated form, it is difficult for an driver to
determine what data is being communicated by the sensor. This allows some
differentiating use cases, where vendor can provide applications. Since these
can't be represented by standard sensor interfaces like IIO, we present these
as fields with
- type (input/output)
- units
- min/max
- get/set value
In addition an dev interface to transfer report events. Details about this
interface is described in /Documentation/hid/hid-sensor.txt. Manufacturers
should not use these ids for any standard sensors, otherwise the the
product/vendor id can be added to black list.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Reviewed-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
In the unlikely case of hdev vanishing while hid_debug_events_read() was
sleeping, we can't really break out of the case switch as with other cases,
as on the way out we'll try to remove ourselves from the hdev waitqueue.
Fix this by taking a shortcut exit path and avoiding cleanup that doesn't
make sense in case hdev doesn't exist any more anyway.
Reported-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Return a negative error code on failure.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret; expression e1,e2;
@@
(
if (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Cintiq 13HD Touch is a new display tablet with pen and 10 finger touches.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Logitech T650 used to report 3 fingers swipes to the up as a press on the
Super key. When we switched the touchpad to the raw mode, we also disable such
firmware gesture and some users may rely on it.
Unfortunately, 3 finger swipes are still not supported in most of the Linux
environments, which means that we disabled a feature of the touchpad.
Allow users to revert the raw reporting mode and keep going with the firmware
gestures by providing a new module parameter.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The device exists with two device IDs instead of one as previously
believed.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
During a stress test these mice kept dropping and reappearing
in runlevel 1 as opposed to 5.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
In wacom_bpt_pen, we checked touch_down before assigning new
stylus_in_proximity value. This would cause stylus_in_proximity not updated
properly if touch is down before pen is in proximity.
[jkosina@suse.cz: fix if-else style]
Signed-off-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Counting number of touching fingers by wacom_wac_finger_count_touches so we
don't have to count them inside individual routines.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The quirk was added for devices that support both pen and touch. It decides if
a device supports multiple inputs by hardcoded feature type. However, for some
devices, we do not know if they support both before accessing their HID
descriptors.
This patch relies on dynamically assigned device_type to make the decision.
Also, we make it certain that wacom_wac->shared is always created. That is, the
driver will not be loaded if it fails to create wacom_wac->shared.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Conflicts:
drivers/hid/wacom_wac.c
Need to fetch the 4.0 fixes to apply 4.1 patches based on top
of those.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Force-beedback core guarantees that the 'effect' pointer that's being passed
to ->upload() callback is non-NULL.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This mouse is also known under other IDs. It needs the quirk or will disconnect
in runlevel 1 or 3.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
CC: stable@vger.kernel.org
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Do not call power_supply_powers() if power_supply_register() failed
earlier. This fixes possible NULL pointer dereference by
power_supply_powers() in such case.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVD1VGAAoJEHm+PkMAQRiG7yoH/juKOQ1zbxi5M+mleDEEJtA0
RxQSojqEMWIKrWi8PNZxjENn1OZB6XOLIXOhlyAZBrmgsjO34p1DyXlZMznr/R8W
kQ2Xxs061hRtB3OuruMIqOApUrjuqsaCwgbgUS1qWmqZcoyZN4oELyZMP6OOlqv5
UUBZm8MfyXGyxrCcg39mjct3VEOhiuEcvL6SUxOC380CdSVAnyqHFPcz0JVqMUn9
9RUBs0T9cMdhb0mZ2bfXzt6AKArj63G2nXOum+VzFcvspSm2U+MPIDCuoE+ZbTPS
jqIAgG0rj1ezRyb5oeJrvlU0Yy3u/cXoMPs9+kORvpladooYNLti8ovh6qllm0I=
=d/ye
-----END PGP SIGNATURE-----
Merge tag 'v4.0-rc5' into next
Merge with the latest upstream to synchronize Synaptics changes
and bring in new infrastructure pieces.
Conflicts:
drivers/input/mouse/synaptics.c
486b908 (HID: wacom: do not send pen events before touch is up/forced out)
introduces a kernel oops when plugging a tablet without touch.
wacom->shared is null for these devices so this leads to a null pointer
exception.
Change the condition to make it clear that what we need is wacom->shared
not NULL.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
If noone listens to the input device when a tool comes in proximity,
the tablet does not send the in-prox event when a client becomes available.
That means that no events will be sent until the tool is taken out of
proximity.
In this situation, ask for the report WACOM_REPORT_INTUOSREAD which will
read the corresponding feature and generate an in-prox event.
To make some generation of hardware working, we need to unset the
quirk NO_GET set by hid-core because the interfaces are seen as "boot
mouse".
We don't schedule this read in a worker while we are in an IO interrupt.
We know that usbhid will do it asynchronously. If this is triggered by
uhid, then this is obviously a client side bug :)
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Since I can't change the type of hid_set_field argument 3, using __force __s32 to remove
this warning.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
For defining enumeration values like report or power status events, the
enumeration usage ids are enclosed in a logical collection. In this case we
need to match logical usage id for pending read on this usage id. For example,
in the below field, when read is requested for 0319, the report will
contain one of the status usages like 850, 851 etc. In this case the raw
event will not match 0319. So when logical collection matches, then wake
up the pending thread.
Physical(Sensor.OtherCustom)
Logical(Sensor.0319)
Application(Sensor.Sensor)
Usage(6)
Sensor.0850
Sensor.0851
Sensor.0852
Sensor.0853
Sensor.0854
Sensor.0855
Logical Minimum(1)
Logical Maximum(5)
Report Size(8)
Report Count(1)
Report Offset(24)
Flags( Array Absolute )
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This driver didn't exist until before v3.19.
Why would suddenly everybody want to build it?
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The PID driver (usbhid/hid-pidff.c) does not set the effect ID when
uploading an effect. The result is that the initial upload works but
subsequent uploads to modify effect parameters are all directed at the
last-created effect.
The targeted effect ID must be passed back to the device when effect
parameters are changed. This is done at the start of
"pidff_set_condition_report", "pidff_set_periodic_report" etc. based on
the value of "pidff->block_load[PID_EFFECT_
BLOCK_INDEX].value[0]".
This value is only ever set during pidff_request_effect_upload.
The result is stored in "pidff->pid_id[effect->id]" at the end of
pid_upload_effect, for later use. However, if an effect is modified and
re-sent then this identifier is not being copied back from
pidff->pid_id[effect->id] before sending the command to the device. The
fix is to do this at the start of pidff_upload_effect.
Signed-off-by: Jim Keir <jimkeir@oracledbadirect.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Many HID driver options are hidden unless EXPERT is set. While I
understand the idea of simplifying the kernel configuration for most
users, in practice I believe it adds more confusion than it helps.
One thing that worries me is that, in non-EXPERT mode, these drivers
will be either built-in or modular based on apparent magic. For
example, switching INPUT and HID from m to y will cause all these
drivers to be built into the kernel when they were previously built
as modules. Short of enabling EXPERT mode altogether, the user has no
control over that.
Generally I do not think tristate options should depend on !EXPERT.
Of these, 11 of 15 are currently in the hid subsystem.
The HID_LOGITECH option is even worse than the others. Sub-options
depend on it, and this causes menuconfig and friends to display the
option even though the user can't change its value. The help page for
HID_LOGITECH will not explain why the value can't be changed. It only
says, for example:
Depends on: INPUT [=y] && HID [=y]
and that leaves the user puzzled about why the option is forced to y.
You might argue that this is a Kconfig bug, but that doesn't make it
less annoying for the user.
Even worse is that some of the sub-options of HID_LOGITECH select
INPUT_FF_MEMLESS, which in turn gets out of control for the user. So,
if you set INPUT=y and HID=y (something most general purpose
distributions would do these days, as both modules would get loaded on
a vast majority of systems otherwise), and you want support for
force-feedback game controllers, you can't have that as a module, it
has to be built-in, regardless of how rare these devices are.
Of course, all this madness goes away once EXPERT is enabled, but then
the rest of the kernel configuration becomes more complex, which
totally voids the original point.
For this reason, I would like all HID device tristate options to be
displayed regardless of EXPERT being set or not. We can let the
default settings still depend on EXPERT, that's not intrusive.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
No need to retrieve the USB handle in input_mapping() when we already
do that in probe. It also allows to use the quirk without having to
add the product ID matching.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The linux kernel has supported the TiVo Slide remote control for some time, but
does not recognize the USB ID of the newer Slide Pro. This patch adds the
missing data structures so the newer remote will be recognized by the driver,
thereby allowing the TiVo, LiveTV, and Thumbs Up/Down buttons to be
mapped with a hwdb file.
Signed-off-by: Forest Wilkinson <web11.forest@tibit.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Change the ownership of power_supply structure from each driver
implementing the class to the power supply core.
The patch changes power_supply_register() function thus all drivers
implementing power supply class are adjusted.
Each driver provides the implementation of power supply. However it
should not be the owner of power supply class instance because it is
exposed by core to other subsystems with power_supply_get_by_name().
These other subsystems have no knowledge when the driver will unregister
the power supply. This leads to several issues when driver is unbound -
mostly because user of power supply accesses freed memory.
Instead let the core own the instance of struct 'power_supply'. Other
users of this power supply will still access valid memory because it
will be freed when device reference count reaches 0. Currently this
means "it will leak" but power_supply_put() call in next patches will
solve it.
This solves invalid memory references in following race condition
scenario:
Thread 1: charger manager
Thread 2: power supply driver, used by charger manager
THREAD 1 (charger manager) THREAD 2 (power supply driver)
========================== ==============================
psy = power_supply_get_by_name()
Driver unbind, .remove
power_supply_unregister()
Device fully removed
psy->get_property()
The 'get_property' call is executed in invalid context because the driver was
unbound and struct 'power_supply' memory was freed.
This could be observed easily with charger manager driver (here compiled
with max17040 fuel gauge):
$ cat /sys/devices/virtual/power_supply/cm-battery/capacity &
$ echo "1-0036" > /sys/bus/i2c/drivers/max17040/unbind
[ 55.725123] Unable to handle kernel NULL pointer dereference at virtual address 00000000
[ 55.732584] pgd = d98d4000
[ 55.734060] [00000000] *pgd=5afa2831, *pte=00000000, *ppte=00000000
[ 55.740318] Internal error: Oops: 80000007 [#1] PREEMPT SMP ARM
[ 55.746210] Modules linked in:
[ 55.749259] CPU: 1 PID: 2936 Comm: cat Tainted: G W 3.19.0-rc1-next-20141226-00048-gf79f475f3c44-dirty #1496
[ 55.760190] Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
[ 55.766270] task: d9b76f00 ti: daf54000 task.ti: daf54000
[ 55.771647] PC is at 0x0
[ 55.774182] LR is at charger_get_property+0x2f4/0x36c
[ 55.779201] pc : [<00000000>] lr : [<c034b0b4>] psr: 60000013
[ 55.779201] sp : daf55e90 ip : 00000003 fp : 00000000
[ 55.790657] r10: 00000000 r9 : c06e2878 r8 : d9b26c68
[ 55.795865] r7 : dad81610 r6 : daec7410 r5 : daf55ebc r4 : 00000000
[ 55.802367] r3 : 00000000 r2 : daf55ebc r1 : 0000002a r0 : d9b26c68
[ 55.808879] Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
[ 55.815994] Control: 10c5387d Table: 598d406a DAC: 00000015
[ 55.821723] Process cat (pid: 2936, stack limit = 0xdaf54210)
[ 55.827451] Stack: (0xdaf55e90 to 0xdaf56000)
[ 55.831795] 5e80: 60000013 c01459c4 0000002a c06f8ef8
[ 55.839956] 5ea0: db651000 c06f8ef8 daebac00 c04cb668 daebac08 c0346864 00000000 c01459c4
[ 55.848115] 5ec0: d99eaa80 c06f8ef8 00000fff 00001000 db651000 c027f25c c027f240 d99eaa80
[ 55.856274] 5ee0: d9a06c00 c0146218 daf55f18 00001000 d99eaa80 db4c18c0 00000001 00000001
[ 55.864468] 5f00: daf55f80 c0144c78 c0144c54 c0107f90 00015000 d99eaab0 00000000 00000000
[ 55.872603] 5f20: 000051c7 00000000 db4c18c0 c04a9370 00015000 00001000 daf55f80 00001000
[ 55.880763] 5f40: daf54000 00015000 00000000 c00e53dc db4c18c0 c00e548c 0000000d 00008124
[ 55.888937] 5f60: 00000001 00000000 00000000 db4c18c0 db4c18c0 00001000 00015000 c00e5550
[ 55.897099] 5f80: 00000000 00000000 00001000 00001000 00015000 00000003 00000003 c000f364
[ 55.905239] 5fa0: 00000000 c000f1a0 00001000 00015000 00000003 00015000 00001000 0001333c
[ 55.913399] 5fc0: 00001000 00015000 00000003 00000003 00000002 00000000 00000000 00000000
[ 55.921560] 5fe0: 7fffe000 be999850 0000a225 b6f3c19c 60000010 00000003 00000000 00000000
[ 55.929744] [<c034b0b4>] (charger_get_property) from [<c0346864>] (power_supply_show_property+0x48/0x20c)
[ 55.939286] [<c0346864>] (power_supply_show_property) from [<c027f25c>] (dev_attr_show+0x1c/0x48)
[ 55.948130] [<c027f25c>] (dev_attr_show) from [<c0146218>] (sysfs_kf_seq_show+0x84/0x104)
[ 55.956298] [<c0146218>] (sysfs_kf_seq_show) from [<c0144c78>] (kernfs_seq_show+0x24/0x28)
[ 55.964536] [<c0144c78>] (kernfs_seq_show) from [<c0107f90>] (seq_read+0x1b0/0x484)
[ 55.972172] [<c0107f90>] (seq_read) from [<c00e53dc>] (__vfs_read+0x18/0x4c)
[ 55.979188] [<c00e53dc>] (__vfs_read) from [<c00e548c>] (vfs_read+0x7c/0x100)
[ 55.986304] [<c00e548c>] (vfs_read) from [<c00e5550>] (SyS_read+0x40/0x8c)
[ 55.993164] [<c00e5550>] (SyS_read) from [<c000f1a0>] (ret_fast_syscall+0x0/0x48)
[ 56.000626] Code: bad PC value
[ 56.011652] ---[ end trace 7b64343fbdae8ef1 ]---
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
[for the nvec part]
Reviewed-by: Marc Dietrich <marvin24@gmx.de>
[for compal-laptop.c]
Acked-by: Darren Hart <dvhart@linux.intel.com>
[for the mfd part]
Acked-by: Lee Jones <lee.jones@linaro.org>
[for the hid part]
Acked-by: Jiri Kosina <jkosina@suse.cz>
[for the acpi part]
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Add new structure 'power_supply_config' for holding run-time
initialization data like of_node, supplies and private driver data.
The power_supply_register() function is changed so all power supply
drivers need updating.
When registering the power supply this new 'power_supply_config' should be
used instead of directly initializing 'struct power_supply'. This allows
changing the ownership of power_supply structure from driver to the
power supply core in next patches.
When a driver does not use of_node or supplies then it should use NULL
as config. If driver uses of_node or supplies then it should allocate
config on stack and initialize it with proper values.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
[for the nvec part]
Reviewed-by: Marc Dietrich <marvin24@gmx.de>
[for drivers/platform/x86/compal-laptop.c]
Reviewed-by: Darren Hart <dvhart@linux.intel.com>
[for drivers/hid/*]
Reviewed-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
According to [1], Windows Precision Touchpad devices must supply
a button type usage in the device capabilities feature report. A
value of 0 indicates that the device contains a depressible
button (i.e. it's a click-pad) whereas a value of 1 indicates
a non-depressible button. Add support for this usage and set
INPUT_PROP_BUTTONPAD on the touchpad input device whenever a
depressible button is present.
[1] https://msdn.microsoft.com/en-us/library/windows/hardware/dn467314(v=vs.85).aspx
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Declare the POWER_SUPPLY_PROP_PRESENT property to provide userspace
with a way to determine if the battery on a wireless tablet is plugged
in. Although current wireless tablets do not explicitly report this
information, it can be inferred from other state information. In
particular, a battery is assumed to be present if any of the following
are true: a non-zero battery level reported, the battery is reported as
charging, or the tablet is operating wirelessly.
Note: The last condition above may not strictly hold for the Graphire
Wireless (it charges from a DC barrel jack instead of a USB port), but I
do not know what is reported in the no-battery condition.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The constant is not used (leftover from previous patch versions
that never got merged).
Reported-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The status packet for tablets which can use a wireless module contains a
bit that is set if the battery is charging. This bit will be 0 if either
a battery is not present or if the battery has reached full charge. Note
that the charging circuit may continue to charge the battery for a short
time after reaching "100%".
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Calls the wacom_status_irq function to report battery status for the
Intuos Pro and Intuos5 (in addition to the already-reporting Intuos
and last-generation Bamboo).
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
If a wireless adapter (which contains the charging circuitry) is
detected as being attached to the tablet then create a new battery
interface and update its status as data is reported. Also destroy the
battery if the adapter goes away.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Tablets like the Intuos, Intuos Pro, and Bamboo have a connector for an
optional wireless module that can be connected on the fly. The presence
(or absence) of this module is indicated in a status report recieved
from the tablet. This patch adds a workqueue function that will create
or destroy a power_supply object at runtime to match the current state
of the WACOM_QUIRK_BATTERY flag.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Has the 'wacom_notify_battery' function take on the job of detecting if
updating the power supply is necessary to remove multiple
nearly-identical 'if' blocks.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
In addition to the touchswitch state for "Intuos", these packets are
also sent by the Intuos Pro, Intuos5, and last-generation Bamboo
tablets when using a wired connection. They contain, among other
things, information about the optional wireless module and battery
charge state (to be supported in subsuquent patches).
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Touchpads that have only one button are called clickpads and should
be advertised as such by the kernel.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Jason Ekstrand <jason@jlekstrand.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Currently HID code maps usages from telephony page into BTN_0, BTN_1, etc
keys which get interpreted by mousedev and userspace as left/right/middle
button clicks, which is not really helpful.
This change adds mappings for usages that have corresponding input event
definitions, and leaves the rest unmapped. This can be changed when
there are userspace consumers for more telephony usages.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
In commit 08177f4 (HID: uclogic: merge hid-huion driver in hid-uclogic)
HID_HUION depends explicitely on USB_HID because it contained quite some
USB-isms.
Now that hid-uclogic is the new home of Huion tablets, we need to also
add the dependency on USB_HID to this driver.
Reported-by: Jiri Kosina <jkosina@suse.cz>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This hack is only needed for Huion tablets. It does not seem to have
any effect on the other tablets handled by this device right now, but
it's better to check for the product id sooner than discovering that
we have messed up one tablet later.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Nikolai Kondrashov <spbnick@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Some Huion tablets present 2 HID Pen interfaces. Only one is used, so
we can drop the unused one.
Reviewed-by: Nikolai Kondrashov <spbnick@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
NO_EMPTY_INPUT is useful when MULTI_INPUT is set. It prevents to create
empty input nodes that user space does not know what to do with.
It does not seem to be required at the moment, this is just a preventive
patch. This check is only made during the plug of the device, so it does
not hurt to have it.
Reviewed-by: Nikolai Kondrashov <spbnick@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
We append "Pen", "Pad", "Mouse", "Keyboard", "Consumer Control" or
"System Control" suffix to the appropriate input node to match what
the Wacom driver does and be more convenient for the user to know
which one is which.
Reviewed-by: Nikolai Kondrashov <spbnick@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Merge the hid-huion driver into hid-uclogic as all the devices supported
by hid-huion are in fact UC-Logic devices.
Signed-off-by: Nikolai Kondrashov <Nikolai.Kondrashov@redhat.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Based on a patch from: Nikolai Kondrashov <Nikolai.Kondrashov@redhat.com>
Most of the tablets handled by hid-uclogic already use MULTI_INPUT.
For the ones which are not quirked in usbhid/hidquirks, they have a
custom report descriptor which contains only one report per HID
interface. For those tablets HID_QUIRK_MULTI_INPUT is transparent.
According to https://github.com/DIGImend/tablets, the only problematic
tablet currently handled by hid-uclogic is the TWHA60 v3. This tablet
presents different report descriptors from the ones currently quirked.
This is not a problem per se, given that this tablet is not supported
currently in this version (it needs the same command as a Huion to
start forwarding events).
Reviewed-by: Nikolai Kondrashov <spbnick@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
touch_down is a flag to indicate if there are touches on tablet
or not. Since one set of touch events may be posted over more
than one data packet/touch frame, and pen may come in proximity
while touch events are partially sent, counting all touch events
for the set reflects the actual status of touch_down.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
If pen comes in proximity while touch is down, we force touch up
before sending pen events. Otherwise, there can be unfinished
touch events compete with pen events. This idea has been fully
implemented for Tablet PCs. But other tablets that support both
pen and touch are not fully considered.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The stylus of this device works just fine out of the box.
The touch is seen by default as a mouse with relative events and some
gestures.
The wireless and the wired version have slightly different firmwares, but
the debug mode 2 on the feature 2 is common to the 2 devices. In this mode,
all the reports are emitted through the debug interface (pen, raw touch
and mouse emulation), so we have to re-route manually the events.
We keep the Pen interface as a HID_GENERIC one because it works, and only
parse the raw touches while discarding the mouse emulation & gestures.
Switching the default in raw mode allows us to have a consistent user
experience accross all the multitouch touchpads (and enable the touch part
of the devices).
Note that the buttons of this devices are reported through the touch
interface. There is no 'Pad' interface. It seemed more natural to have
the BTN_LEFT and BTN_RIGHT reported with the touch because they are
placed under the touch interface and it looks like they belong to the
touch part.
Tested-by: Josep Sanchez Ferreres <josep.sanchez.ferreres@est.fib.upc.edu>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Bamboo PAD in debug mode needs to re-route events from the debug
interface to the Pen interface. This can be easily done with
hid_input_report(), but that means that we need to keep a reference to
the various hid_devices.
There should be only one touch and one pen interface per physical tablet,
so there is no need to keep a list of hid-devices, plain pointers are
sufficient.
Tested-by: Josep Sanchez Ferreres <josep.sanchez.ferreres@est.fib.upc.edu>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
These 2 are left over from the USB dependency cleaning, so there is
no need to keep them.
[jkosina@suse.cz: fix filename]
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
A touchpad may have firmware based palm detection code enabled which
suppresses 2D data from being reported when the firmware believes a palm is
on the touchpad. This functionality is meant to be used in mouse mode without
a driver. When a driver is present, the driver can do a better job of
determining if a contact is a palm. If this gesture is enabled on a touchpad
operating in rmi mode then the firmware will not properly clear the palm detect
interrupt, causing the touchpad to interrupt indefinately. This patch disables
the palm detect gesture when the touchpad is operating in rmi mode.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Tested-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When a finger is lifted from a Synaptics touchpad the firmware will continue
to interrupts for up to a second. These additional interrupts are know and
dribble interrupts. Since the data read from the touchpad does not change
the input subsystem only reports a single event. This makes the servicing of
dribble interrupts on Linux unnecessary. This patch simply disables dribble
interupts when configuring the touchpad.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Tested-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The HID over I2C specification allows to have the interrupt for a HID
device to be GPIO instead of directly connected to the IO-APIC.
Add support for this so that when the driver does not find proper interrupt
number from the I2C client structure we check if it has ACPI GpioInt()
resource listed in _CRS. If it is found we convert it to an interrupt
number and use it instead.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Lenovo Thinkpad 10 has wacom digitizer connected as a I2C-HID device. Add
generic support for this.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This commit exposes in sysfs the HID country code that is stored in the country
member of hid_device structure. It identifies the country code of localized
hardware.
For example some keyboards use it to exhibit the language of the key layout. It
helps the upper layer to identify the localized hardware and setup the correct
language to use.
For USB HID devices the country code comes for the HID descriptor and for
Bluetooth HID devices it is the HIDCountryCode attribute from the SDP database.
Signed-off-by: Olivier Gay <ogay@logitech.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Microsoft Natural Wireless Ergonomic Keyboard 7000 has special My
Favorites 1..5 keys which are handled through a vendor-defined usage
page (0xff05).
Apply MS_ERGONOMY quirks handling to USB PID 0x071d (Microsoft Microsoft
2.4GHz Transceiver V1.0) so that the My Favorites 1..5 keys are reported
as KEY_F14..18 events.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=52841
Signed-off-by: Jakub Sitnicki <jsitnicki@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Current API only allows setting one offset in the field. This API
is extended to set multiple offsets in the field report.
Also update parameters in the users of this API.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Reviewed-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Some hid sensor feature report can contain more than one reports.
This API can now support receiving multiple values from the feature
report.
Also update the parameters in the users of this API.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add additional flag to read in async mode. In this mode the caller will get
reply via registered callback for capture_sample. Callbacks can be registered
using sensor_hub_register_callback function. The usage id parameter of the
capture_sample can be matched with the usage id of the requested attribute.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Section 4.2.5 of HID Sensor hub specification allows two methods
defining sensor devices.
- Each sensor device by its own collection
- A top level application collection object, including multiple
sensors.
In the first method, each sensor can be in its own sensor application
collection without a physical collection.
In the second method there is a usage id for collection type, which
is defined as an application collection, with multiple physical
collections in it. It is possible to define fusion sensor with this
and may have its own handler. If there is a callback registered
for the collection type, then forward all reports for sensors in
its collection to this handler.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Current implementation only allows one outstanding synchronous read.
This is a performance hit when user mode is requesting raw reads
of sensor attributes on multiple sensors together.
This change changes the mutex lock to per hid sensor hub device instead
of global lock. Although request to hid sensor hub is serialized, there
can be multiple outstanding read requests pending for responses via
hid reports.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
d1c7e29e8d (HID: i2c-hid: prevent buffer overflow in early IRQ)
changed hid_get_input() to read ihid->bufsize bytes, which can be
more than wMaxInputLength. This is the case with the Dell XPS 13
9343, and it is causing events to be missed. In some cases the
missed events are releases, which can cause the cursor to jump or
freeze, among other problems. Limit the number of bytes read to
min(wMaxInputLength, ihid->bufsize) to prevent such problems.
Fixes: d1c7e29e8d "HID: i2c-hid: prevent buffer overflow in early IRQ"
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Per-controller spinlock needs to be properly initialized during device probe.
[jkosina@suse.cz: massage changelog]
[jkosina@suse.cz: drop hunk that has already been applied by previous
patch]
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
sony_dev_list_lock spinlock (which was introduced in d2d782fcce ("HID: sony:
Prevent duplicate controller connections") is not being initialized properly.
Fix that.
Reported-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Fix "undefined reference" build issue with CONFIG_USB disabled; make the
driver use generic HID API instead.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Michal Malý <madcatxster@devoid-pointer.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
input_mt_sync_frame() calls input_mt_report_pointer_emulation() and do
some internal steps required to keep in sync the state of the touch within
the various reports.
Given that we use input_mt_get_slot_by_key() in this driver, it is better to
use input_mt_sync_frame().
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Don't mix declaration and allocation, remove some useless newlines
between calling a function and checking its return value.
Signed-off-by: Antonio Ospite <ao2@ao2.it>
Acked-by: Frank Praznik <frank.praznik@oh.rr.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Use the same type declared in the prototypes of functions that are going
to accept the buffer as parameter.
Signed-off-by: Antonio Ospite <ao2@ao2.it>
Acked-by: Frank Praznik <frank.praznik@oh.rr.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Remove the magic numbers used in sixaxis_set_operational_usb():
- use the already defined SIXAXIS_REPORT_0xF2_SIZE;
- define and use SIXAXIS_REPORT_0xF5_SIZE;
- set the dummy buffer size to accommodate any report that is going to
be requested.
Signed-off-by: Antonio Ospite <ao2@ao2.it>
Acked-by: Frank Praznik <frank.praznik@oh.rr.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Sixaxis devices accept feature report 0xf2 when size is >= 17, not 18.
Use the minimum accepted size.
The change is mainly for documentation purposes, the code worked fine
even before this change.
Signed-off-by: Antonio Ospite <ao2@ao2.it>
Acked-by: Frank Praznik <frank.praznik@oh.rr.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
ida_destroy() must be called _after_ all the devices have been
unregistered; otherwise, when calling "rmmod hid_sony" with devices
still plugged in, the following warning would show up because of calls
to ida_simple_remove() on a destroyed ID allocator:
------------[ cut here ]------------
WARNING: CPU: 0 PID: 5509 at lib/idr.c:1052 ida_simple_remove+0x26/0x50()
ida_remove called for id=0 which is not allocated.
Modules linked in: ...
CPU: 0 PID: 5509 Comm: rmmod Not tainted 3.19.0-rc6-ao2 #35
Hardware name: System manufacturer System Product Name/M2N-MX SE, BIOS 0501 03/20/2008
0000000000000000 ffffffff8176320d ffffffff815b3a88 ffff880036f7fdd8
ffffffff8106ce01 0000000000000000 ffffffffa07658e0 0000000000000246
ffff88005077d8b8 ffff88005077d8d0 ffffffff8106ce7a ffffffff81763260
Call Trace:
[<ffffffff815b3a88>] ? dump_stack+0x40/0x50
[<ffffffff8106ce01>] ? warn_slowpath_common+0x81/0xb0
[<ffffffff8106ce7a>] ? warn_slowpath_fmt+0x4a/0x50
[<ffffffff812ccb86>] ? ida_simple_remove+0x26/0x50
[<ffffffffa0762dc8>] ? sony_remove+0x58/0xe0 [hid_sony]
[<ffffffffa00fff15>] ? hid_device_remove+0x65/0xd0 [hid]
[<ffffffff8140425e>] ? __device_release_driver+0x7e/0x100
[<ffffffff81404c70>] ? driver_detach+0xa0/0xb0
[<ffffffff81403ee5>] ? bus_remove_driver+0x55/0xe0
[<ffffffffa01000ff>] ? hid_unregister_driver+0x2f/0xa0 [hid]
[<ffffffff810e45bf>] ? SyS_delete_module+0x1bf/0x270
[<ffffffff81014089>] ? do_notify_resume+0x69/0xa0
[<ffffffff815b952d>] ? system_call_fastpath+0x16/0x1b
---[ end trace bc794b3d22c30ede ]---
Signed-off-by: Antonio Ospite <ao2@ao2.it>
Acked-by: Frank Praznik <frank.praznik@oh.rr.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Allow switching of Logitech gaming wheels between available compatibility modes
through sysfs. This only applies to multimode wheels.
Signed-off-by: Michal Malý <madcatxster@devoid-pointer.net>
Tested-by: Simon Wood <simon@mungewell.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Introduce a module parameter to disable automatic switch of Logitech gaming
wheels from compatibility to native mode. This only applies to multimode wheels.
Signed-off-by: Michal Malý <madcatxster@devoid-pointer.net>
Tested-by: Simon Wood <simon@mungewell.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Display the real wheel model and supported alternate modes through sysfs. This
applies only to multimode wheels.
Signed-off-by: Michal Malý <madcatxster@devoid-pointer.net>
Tested-by: Simon Wood <simon@mungewell.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Identify Logitech gaming wheels in compatibility modes accordingly to Logitech
specifications.
Logitech specification contains a general method of identifying various
models of their gaming wheels while they are in "compatibility" mode.
This patch implements the method instead of checking against known
values of bcdDevice. Handling of the mode switch upon initialization is
also adjusted so that the driver does not have to go through the entire
initialization routine because the wheels are set to perform a USB
detach before they reappear in "native" mode.
Signed-off-by: Michal Malý <madcatxster@devoid-pointer.net>
Tested-by: Simon Wood <simon@mungewell.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Commit 0ccf091d1f ("HID: sensor-hub:
make dyn_callback_lock IRQ-safe) was supposed to change locks
in sensor_hub_get_callback(), but missed.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Knowing the firmware id is extremely useful when debugging issues related to
the touchpad. It can be used to determine the hardware, firmware version,
and configuation of the touchpad. This patch queries the firmware id and
prints it as the touchpad is starting so that it will show up in the dmesg
output included in bug reports.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Microsoft HID over I2C specification says two things regarding the
interrupt:
1) The interrupt should be level sensitive
2) The device keeps the interrupt asserted as long as it has more reports
available.
We've seen that at least some Atmel and N-Trig panels keep the line low as
long as they have something to send. The current version of the driver only
detects the first edge but then fails to read rest of the reports (as the
line is still asserted).
Make the driver follow the specification and configure the HID interrupt to
be level sensitive.
The Windows HID over I2C driver also seems to do the same.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Without this, my "Gasia Co.,Ltd PS(R) Gamepad" would not send
any events. Now everything works including the leds.
Based on work by Andrew Haines and Antonio Ospite.
cc: Antonio Ospite <ao2@ao2.it>
cc: Andrew Haines <AndrewD207@aol.com>
Signed-off-by: Lauri Kasanen <cand@gmx.com>
Reviewed-by: Antonio Ospite <ao2@ao2.it>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Genius PenSketch M912 digitizer tablet sends incorrect report descriptor by
default. This patch replaces it with a corrected one.
Signed-off-by: Milan Plzik <milan.plzik@gmail.com>
Reviewed-by: Nikolai Kondrashov <spbnick@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
27QHD has the same x_min/y_min (WACOM_CINTIQ_OFFSET) as other Cintiqs.
ABS_MISC event is required for PAD packet to work properly with
xf86-input-wacom.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
These devices have accelerometers. To report accelerometer coordinates, a new
property, INPUT_PROP_ACCELEROMETER, is added.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
After PAD moved to its own interface, there were duplicated statements in
wacom_setup_pentouch_input_capabilities. Merge them together to reduce future
maintenance effort.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
stylus_in_proximity is used to make sure no touch event is sent while pen is in
proximity. touch_down is used to make sure a touch up event is sent when pen
comes into proximity while touch is down.
Two touch routines didn't store touch_down. One touch routine forgot to check
stylus_in_proximity before sending touch events. This patch fixes those issues.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The FF2 driver (usbhid/hid-pidff.c) sends commands to the stick during ff_init.
However, this is called inside a block where driver_input_lock is locked, so
the results of these initial commands are discarded. This behavior is the
"killer", without this nothing else works.
ff_init issues commands using "hid_hw_request". This eventually goes to
hid_input_report, which returns -EBUSY because driver_input_lock is locked. The
change is to delay the ff_init call in hid-core.c until after this lock has
been released.
Calling hid_device_io_start() releases the lock so the device can be
configured. We also need to call hid_device_io_stop() on exit for the lock to
remain locked while ending the init of the drivers.
[ benjamin.tissoires@redhat.com: imrpoved the changelog a lot ]
Signed-off-by: Jim Keir <jimkeir@oracledbadirect.com>
Reviewed-by: Benjamin.tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The return type of wait_for_completion_timeout is unsigned long not
int. This patch fixes up the declarations only.
Patch was compile tested only for x86_64_defconfig + CONFIG_X86_VSMP=y
CONFIG_HYPERV=m, CONFIG_HID_HYPERV_MOUSE=m
Signed-off-by: Nicholas Mc Guire <der.herr@hofr.at>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
It appears that the Cintiq Companion Hybrid does not send an ABS_MISC event to
userspace when any of its ExpressKeys are pressed. This is not strictly
necessary now that the pad exists on its own device, but should be fixed for
consistency's sake.
Traditionally both the stylus and pad shared the same device node, and
xf86-input-wacom would use ABS_MISC for disambiguation. Not sending this causes
the Hybrid to behave incorrectly with xf86-input-wacom beginning with its
8f44f3 commit.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Use <driver>-$(CONFIG_FOO) syntax to build multipart objects with
optional parts, since all the config options are bool. Also, delete the
obvious comments in the usbhid Makefile.
Signed-off-by: Michal Marek <mmarek@suse.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Microchip Pick16F1454 is exported as a HID device and is used by for
example the Yepkit YKUSH three-port switchable USB hub. However, it is not an
actual HID-device. On the Yepkit, it is used to power up/down the ports on the
hub. The HID driver should ignore this device.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Use the DEVICE_ATTR_RW macro to reduce boiler plate and move the
attribute declaration to get rid of function signatures.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
There is no reason to set the range attribute executable to the user and
group, and writable to the group. Fix the permission to 0644.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Some Cintiq and Intuos tablets report In Range event. This event is sent before
valid data is reported when tool enters proximity; or before out of proximity
event is reported when tool exits.
While entering proximity, In Range means a pen is detected. This information
can be used for palm/touch rejection on both pen and touch enabled devices.
While exiting, it means the tool has reached its maximum detectable distance.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Users may use unsupported tools on Cintiq or Intuos. When invalid tools or data
are detected, they should be ignored. That is, no event from those tools should
be reported.
Consolidating that code in wacom_intuos_inout simplifies the logic and make it
easier for future code change.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Have hid-rmi handle all of the Razer Blade HID devices that are part of the
composite USB device. This will allow hid-rmi to operate the touchpad in rmi
mode while passing events from the other devices to hid-input.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The external buttons on HID touchpads are connected as pass through devices and
button events are not reported in the rmi registers. As a result on these
devices we need to allow the HID generic desktop button events to be processed
by hid-input. Unfortunately, there is no way to query the touchpad to determine
that it has pass through buttons so the RMI_DEVICE_HAS_PHYS_BUTTONS should be
set manually when adding the device to rmi_id[].
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Now that hid_report_len is in hid.h we can use this function instead of
duplicating the code which computes it.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This is a static checker fix. We write some binary settings to the
sysfs file. One of the settings is the "->startup_profile". There
isn't any checking to make sure it fits into the
pyra->profile_settings[] array in the profile_activated() function.
I added a check to pyra_sysfs_write_settings() in both places because
I wasn't positive that the other callers were correct.
Cc: <stable@vger.kernel.org>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
If a disconnect occurs while getting the actual name of the device
(which can take several HID transactions), the name of the device will
be the hid name, provided by the Unifying Receiver.
This means that in some cases, the user space will see a different
name that what it usually sees when there is no disconnect.
We should store the name of the device in the struct hidpp. That way,
if a disconnect occurs while we are accessing the name,
hidpp_connect_event() can fail, and the input node is not created.
The input node will be created only if we have a connection which
lasts long enough to retrieve all the requested information:
name, protocol, and specific configuration.
Reviewed-by: Peter Wu <peter@lekensteyn.nl>
Tested-by: Peter Wu <peter@lekensteyn.nl>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Based on code for the US Surface Type Cover 3
from commit be3b16341d
("HID: add support for MS Surface Pro 3 Type Cover"):
Signed-off-by: Alan Wu <alan.c.wu@gmail.com>
Tested-by: Karlis Dreizis <karlisdreizis@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The ignore check that got added in 6ce901eb61 ("HID: input: fix confusion
on conflicting mappings") needs to properly check for VARIABLE reports
as well (ARRAY reports should be ignored), otherwise legitimate keyboards
might break.
Cc: <stable@vger.kernel.org>
Fixes: 6ce901eb61 ("HID: input: fix confusion on conflicting mappings")
Reported-by: Fredrik Hallenberg <megahallon@gmail.com>
Reported-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
On an PC-101/103/104 keyboard (American layout) the 'Enter' key and its
neighbours look like this:
+---+ +---+ +-------+
| 1 | | 2 | | 5 |
+---+ +---+ +-------+
+---+ +-----------+
| 3 | | 4 |
+---+ +-----------+
On a PC-102/105 keyboard (European layout) it looks like this:
+---+ +---+ +-------+
| 1 | | 2 | | |
+---+ +---+ +-+ 4 |
+---+ +---+ | |
| 3 | | 5 | | |
+---+ +---+ +-----+
(Note that the number of keys is the same, but key '5' is moved down and
the shape of key '4' is changed. Keys '1' to '3' are exactly the same.)
The keys 1-4 report the same scan-code in HID in both layouts, even though
the keysym they produce is usually different depending on the XKB-keymap
used by user-space.
However, key '5' (US 'backslash'/'pipe') reports 0x31 for the upper layout
and 0x32 for the lower layout, as defined by the HID spec. This is highly
confusing as the linux-input API uses a single keycode for both.
So far, this was never a problem as there never has been a keyboard with
both of those keys present at the same time. It would have to look
something like this:
+---+ +---+ +-------+
| 1 | | 2 | | x31 |
+---+ +---+ +-------+
+---+ +---+ +-----+
| 3 | |x32| | 4 |
+---+ +---+ +-----+
HID can represent such a keyboard, but the linux-input API cannot.
Furthermore, any user-space mapping would be confused by this and,
luckily, no-one ever produced such hardware.
Now, the HID input layer fixed this mess by mapping both 0x31 and 0x32 to
the same keycode (KEY_BACKSLASH==0x2b). As only one of both physical keys
is present on a hardware, this works just fine.
Lets introduce hardware-vendors into this:
------------------------------------------
Unfortunately, it seems way to expensive to produce a different device for
American and European layouts. Therefore, hardware-vendors put both keys,
(0x31 and 0x32) on the same keyboard, but only one of them is hooked up
to the physical button, the other one is 'dead'.
This means, they can use the same hardware, with a different button-layout
and automatically produce the correct HID events for American *and*
European layouts. This is unproblematic for normal keyboards, as the
'dead' key will never report any KEY-DOWN events. But RollOver keyboards
send the whole matrix on each key-event, allowing n-key roll-over mode.
This means, we get a 0x31 and 0x32 event on each key-press. One of them
will always be 0, the other reports the real state. As we map both to the
same keycode, we will get spurious key-events, even though the real
key-state never changed.
The easiest way would be to blacklist 'dead' keys and never handle those.
We could simply read the 'country' tag of USB devices and blacklist either
key according to the layout. But... hardware vendors... want the same
device for all countries and thus many of them set 'country' to 0 for all
devices. Meh..
So we have to deal with this properly. As we cannot know which of the keys
is 'dead', we either need a heuristic and track those keys, or we simply
make use of our value-tracking for HID fields. We simply ignore HID events
for absolute data if the data didn't change. As HID tracks events on the
HID level, we haven't done the keycode translation, yet. Therefore, the
'dead' key is tracked independently of the real key, therefore, any events
on it will be ignored.
This patch simply discards any HID events for absolute data if it didn't
change compared to the last report. We need to ignore relative and
buffered-byte reports for obvious reasons. But those cannot be affected by
this bug, so we're fine.
Preferably, we'd do this filtering on the HID-core level. But this might
break a lot of custom drivers, if they do not follow the HID specs.
Therefore, we do this late in hid-input just before we inject it into the
input layer (which does the exact same filtering, but on the keycode
level).
If this turns out to break some devices, we might have to limit filtering
to EV_KEY events. But lets try to do the Right Thing first, and properly
filter any absolute data that didn't change.
This patch is tagged for 'stable' as it fixes a lot of n-key RollOver
hardware. We might wanna wait with backporting for a while, before we know
it doesn't break anything else, though.
Cc: <stable@vger.kernel.org>
Reported-by: Adam Goode <adam@spicenitz.org>
Reported-by: Fredrik Hallenberg <megahallon@gmail.com>
Tested-by: Fredrik Hallenberg <megahallon@gmail.com>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Bamboo Pads are using the generic processing but their report descriptors
differ from the ISDv* line. The pen fields are marked with the .physical
as Digitizer_Pen, which makes also sense.
Add this field to the checks and enable for free Bamboo Pads.
Reported-by: Josep Sanchez Ferreres <josep.sanchez.ferreres@est.fib.upc.edu>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
We introduced nice macros in wacom_wac.c to check whether a field is
a pen or a touch one.
wacom_usage_mapping() still uses it's own tests, which are not in sync with
the wacom_wac tests (.application is not checked).
That means that some legitimate fields might be filtered out from the
usage mapping, and thus will not be used properly while receiving the
events.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
New Genius MousePen i608X devices have a new id 0x501a instead of the
old 0x5011 so add a new #define with "_2" appended and change required
places.
The remaining two checkpatch warnings about line length
being over 80 characters are present in the original files too and this
patch was made in the same style (no line break).
Just adding a new id and changing the required places should make the
new device work without any issues according to the bug report in the
following url.
This patch was made according to and fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=67111
Signed-off-by: Giedrius Statkevičius <giedrius.statkevicius@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Commit fc38a8a66e ("HID: add BETOP game controller force feedback support")
is missing the actual addition of drivers/hid/hid-betopff.c due to my
mistake (I forgot to add the file after fixing conflicts).
Fixes: fc38a8a66e ("HID: add BETOP game controller force feedback support")
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Adds force feedback support for BETOP USB game controllers.
These devices are mass produced in China.
Signed-off-by: Huang Bo <huangbobupt@163.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Allowing hid-rmi to bind to non rmi devices allows us to support composite USB
devices which contain several HID devices one of which is a HID touchpad.
Since all of the devices have the same VID and PID we can add the device
to the hid_have_special_driver list and have hid-rmi handle all of the devices.
Then hid-rmi's probe can look for the rmi specific HID report IDs and decide if
it should handle the device as a rmi device or simply report that the events
needs additional processing.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Current names are reported as "K750", "M705", and it can be misleading
for the users when they look at their input device list.
Prefixing the names with "Logitech " makes things better.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Peter Wu <peter@lekensteyn.nl>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add a return to avoid a fall-through. Introduced in commit
57ac86cf52 ("HID: logitech-hidpp: add
support of the first Logitech Wireless Touchpad").
Signed-off-by: Peter Wu <peter@lekensteyn.nl>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Devices speaking HID++ 2.0 report a different error code (0xff). Detect
these errors too to avoid 5 second delays when the device reports an
error. Caught by... well, a bug in the QEMU emulation of this receiver.
Renamed fap to rap for HID++ 1.0 errors because it is more logical,
it has no functional difference.
Signed-off-by: Peter Wu <peter@lekensteyn.nl>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Allows for HID_BATTERY_STRENGTH config be enabled without the need for HID
module to be built-in, prior to this HID and POWER_SUPPLY had to be equal, and
now we only select POWER_SUPPLY and depend on the HID module.
Signed-off-by: Daniel Nicoletti <dantti12@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Current names are reported as "K750", "M705", and it can be misleading
for the users when they look at their input device list.
Prefixing the names with "Logitech " makes things better.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Peter Wu <peter@lekensteyn.nl>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When a hid driver that uses i2c-hid as transport is unloaded, the hid core
will call i2c_hid_stop() which releases all the buffers associated with the
device. This includes also the command buffer.
Now, when the i2c-hid driver itself is unloaded it tries to power down the
device by sending it PWR_SLEEP command. Since the command buffer is already
released we get following crash:
[ 79.691459] BUG: unable to handle kernel NULL pointer dereference at (null)
[ 79.691532] IP: [<ffffffffa05bc049>] __i2c_hid_command+0x49/0x310 [i2c_hid]
...
[ 79.693467] Call Trace:
[ 79.693494] [<ffffffff810424e1>] ? __unmask_ioapic+0x21/0x30
[ 79.693537] [<ffffffff81042855>] ? unmask_ioapic+0x25/0x40
[ 79.693581] [<ffffffffa05bc35b>] ? i2c_hid_set_power+0x4b/0xa0 [i2c_hid]
[ 79.693632] [<ffffffffa05bc3cf>] ? i2c_hid_runtime_resume+0x1f/0x30 [i2c_hid]
[ 79.693689] [<ffffffff814c08fb>] ? __rpm_callback+0x2b/0x70
[ 79.693733] [<ffffffff814c0961>] ? rpm_callback+0x21/0x90
[ 79.693776] [<ffffffff814c0dec>] ? rpm_resume+0x41c/0x600
[ 79.693820] [<ffffffff814c1e1c>] ? __pm_runtime_resume+0x4c/0x80
[ 79.693868] [<ffffffff814b8588>] ? __device_release_driver+0x28/0x100
[ 79.693917] [<ffffffff814b8d90>] ? driver_detach+0xa0/0xb0
[ 79.693959] [<ffffffff814b82cc>] ? bus_remove_driver+0x4c/0xb0
[ 79.694006] [<ffffffff810d1cfd>] ? SyS_delete_module+0x11d/0x1d0
[ 79.694054] [<ffffffff8165f107>] ? int_signal+0x12/0x17
[ 79.694095] [<ffffffff8165ee69>] ? system_call_fastpath+0x12/0x17
Fix this so that we only free buffers when the i2c-hid driver itself is
removed.
Fixes: 34f439e4af ("HID: i2c-hid: add runtime PM support")
Reported-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
On composite HID devices there may be multiple HID devices on separate
interfaces, but hid-rmi should only bind to the touchpad. The previous version
simply checked that the interface protocol was set to mouse. Unfortuately, it
is not always the case that the touchpad has the mouse interface protocol set.
This patch takes a different approach and scans the report descriptor looking
for the Generic Desktop Pointer usage and the Vendor Specific Top Level
Collection needed by the hid-rmi driver to interface with the device.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
If wtp_connect() fails, that means most of the time that the device has
been disconnected. Subsequent attempts to contact the device will fail
too, so it's simpler to bail out earlier.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Peter Wu <peter@lekensteyn.nl>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Apple bluetooth wireless keyboard (sold in UK) has always reported zero
for battery strength no matter what condition the batteries are actually
in. With this patch applied (applying same quirk as other Apple
keyboards), the battery strength is now correctly reported.
Signed-off-by: Karl Relton <karllinuxtest.relton@ntlworld.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
By default the middle button is in a compatibility mode, and generates
standard wheel events when dragging with the middle trackpoint button.
Unfortunately this is buggy:
* The middle button comes up before starting wheel events, causing a middle
click on whatever the mouse cursor was sitting on
* The USB keyboard always generates the "native" horizontal wheel event,
regardless of mode.
Instead, enable the "native" mode the Windows driver uses, and add support
for the custom events this generates. This fixes the USB keyboard wheel
events, and the middle-click up event comes after the wheel events.
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The trackpoint sensitivity can also be controlled, expose this via
sysfs.
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Previously wtp_raw_event would be called through
hidpp_raw_hidpp_event (for the touchpad report) and hidpp_raw_event
(for the mouse report).
This patch removes one calling surface, making a clearer distinction
between "generic HID++ processing" (matching internal reports) and
device-specific event processing.
Suggested-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Peter Wu <peter@lekensteyn.nl>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Malicious USB devices can send bogus reports smaller than the expected
buffer size. Ensure that the length for WTP reports is valid to avoid
reading out of bounds.
Signed-off-by: Peter Wu <peter@lekensteyn.nl>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Malicious USB devices can send bogus reports smaller than the expected
buffer size. Ensure that the length is valid to avoid reading out of
bounds.
Signed-off-by: Peter Wu <peter@lekensteyn.nl>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Pull HID updates from Jiri Kosina:
- i2c-hid race condition fix from Jean-Baptiste Maneyrol
- Logitech driver now supports vendor-specific HID++ protocol, allowing
us to deliver a full multitouch support on wider range of Logitech
touchpads. Written by Benjamin Tissoires
- MS Surface Pro 3 Type Cover support added by Alan Wu
- RMI touchpad support improvements from Andrew Duggan
- a lot of updates to Wacom driver from Jason Gerecke and Ping Cheng
- various small fixes all over the place
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (56 commits)
HID: rmi: The address of query8 must be calculated based on which query registers are present
HID: rmi: Check for additional ACM registers appended to F11 data report
HID: i2c-hid: prevent buffer overflow in early IRQ
HID: logitech-hidpp: disable io in probe error path
HID: logitech-hidpp: add boundary check for name retrieval
HID: logitech-hidpp: check name retrieval return code
HID: logitech-hidpp: do not return the name length
HID: wacom: Report input events for each finger on generic devices
HID: wacom: Initialize MT slots for generic devices at post_parse_hid
HID: wacom: Update maximum X/Y accounding to outbound offset
HID: wacom: Add support for DTU-1031X
HID: wacom: add defines for new Cintiq and DTU outbound tracking
HID: wacom: fix freeze on open when autosuspend is on
HID: wacom: re-add accidentally dropped Lenovo PID
HID: make hid_report_len as a static inline function in hid.h
HID: wacom: Consult the application usage when determining field type
HID: wacom: PAD is independent with pen/touch
HID: multitouch: Add quirk for VTL touch panels
HID: i2c-hid: fix race condition reading reports
HID: wacom: Add angular resolution data to some ABS axes
...
If a touchpad does not report relative data then query 6 will not be present and the address
of query 8 will be one less. This patches calculates the location of query 8 instead of
hardcoding the offset.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
If a touchpad reports the F11 data40 register then this indicates that the touchpad reports
additional ACM (Accidental Contact Mitigation) data after the F11 data in the HID attention
report. These additional bytes shift the position of the F30 button data causing the driver
to incorrectly report button state when this functionality is present. This patch accounts
for the additional data in the report.
Fixes:
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1398533
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Before ->start() is called, bufsize size is set to HID_MIN_BUFFER_SIZE,
64 bytes. While processing the IRQ, we were asking to receive up to
wMaxInputLength bytes, which can be bigger than 64 bytes.
Later, when ->start is run, a proper bufsize will be calculated.
Given wMaxInputLength is said to be unreliable in other part of the
code, set to receive only what we can even if it results in truncated
reports.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Balance a hid_device_io_start() call with hid_device_io_stop() in the
error path. This avoids processing of HID reports when the probe fails
which possibly leads to invalid memory access in hid_device_probe() as
report_enum->report_id_hash might already be freed via
hid_close_report().
hid_set_drvdata() is called before wtp_allocate, be consistent and clear
drvdata too on the error path of wtp_allocate.
Signed-off-by: Peter Wu <peter@lekensteyn.nl>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The HID response has a limited size. Do not trust the value returned by
hardware, check that it really fits in the message.
Signed-off-by: Peter Wu <peter@lekensteyn.nl>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
hidpp_devicenametype_get_device_name() may return a negative value on
protocol errors (for example, when the device is powered off).
Explicitly check this condition to avoid a long-running loop.
(0 cannot be returned as __name_length - index > 0, but check for it
anyway as it would otherwise result in an infinite loop.)
Signed-off-by: Peter Wu <peter@lekensteyn.nl>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
We do not make any use of the actual name length get through
hidpp_get_device_name(). Original patch by Benjamin Tissoires, this
patch also replaces a (now) unnecessary goto by return NULL.
Signed-off-by: Peter Wu <peter@lekensteyn.nl>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The existing generic touch code only reports events after reading an
entire HID report, which practically means that only data about the last
contact in a report will ever be provided to userspace. This patch uses
a trick from hid-multitouch.c to discover what type of field is at the
end of each contact; when such a field is encountered all the stored
contact data will be reported.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This time we have some more new material than we used to have during
the last couple of development cycles.
The most important part of it to me is the introduction of a unified
interface for accessing device properties provided by platform
firmware. It works with Device Trees and ACPI in a uniform way and
drivers using it need not worry about where the properties come
from as long as the platform firmware (either DT or ACPI) makes
them available. It covers both devices and "bare" device node
objects without struct device representation as that turns out to
be necessary in some cases. This has been in the works for quite
a few months (and development cycles) and has been approved by
all of the relevant maintainers.
On top of that, some drivers are switched over to the new interface
(at25, leds-gpio, gpio_keys_polled) and some additional changes are
made to the core GPIO subsystem to allow device drivers to manipulate
GPIOs in the "canonical" way on platforms that provide GPIO information
in their ACPI tables, but don't assign names to GPIO lines (in which
case the driver needs to do that on the basis of what it knows about
the device in question). That also has been approved by the GPIO
core maintainers and the rfkill driver is now going to use it.
Second is support for hardware P-states in the intel_pstate driver.
It uses CPUID to detect whether or not the feature is supported by
the processor in which case it will be enabled by default. However,
it can be disabled entirely from the kernel command line if necessary.
Next is support for a platform firmware interface based on ACPI
operation regions used by the PMIC (Power Management Integrated
Circuit) chips on the Intel Baytrail-T and Baytrail-T-CR platforms.
That interface is used for manipulating power resources and for
thermal management: sensor temperature reporting, trip point setting
and so on.
Also the ACPI core is now going to support the _DEP configuration
information in a limited way. Basically, _DEP it supposed to reflect
off-the-hierarchy dependencies between devices which may be very
indirect, like when AML for one device accesses locations in an
operation region handled by another device's driver (usually, the
device depended on this way is a serial bus or GPIO controller).
The support added this time is sufficient to make the ACPI battery
driver work on Asus T100A, but it is general enough to be able to
cover some other use cases in the future.
Finally, we have a new cpufreq driver for the Loongson1B processor.
In addition to the above, there are fixes and cleanups all over the
place as usual and a traditional ACPICA update to a recent upstream
release.
As far as the fixes go, the ACPI LPSS (Low-power Subsystem) driver
for Intel platforms should be able to handle power management of
the DMA engine correctly, the cpufreq-dt driver should interact
with the thermal subsystem in a better way and the ACPI backlight
driver should handle some more corner cases, among other things.
On top of the ACPICA update there are fixes for race conditions
in the ACPICA's interrupt handling code which might lead to some
random and strange looking failures on some systems.
In the cleanups department the most visible part is the series
of commits targeted at getting rid of the CONFIG_PM_RUNTIME
configuration option. That was triggered by a discussion
regarding the generic power domains code during which we realized
that trying to support certain combinations of PM config options
was painful and not really worth it, because nobody would use them
in production anyway. For this reason, we decided to make
CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and that lead to the
conclusion that the latter became redundant and CONFIG_PM could
be used instead of it. The material here makes that replacement
in a major part of the tree, but there will be at least one more
batch of that in the second part of the merge window.
Specifics:
- Support for retrieving device properties information from ACPI
_DSD device configuration objects and a unified device properties
interface for device drivers (and subsystems) on top of that.
As stated above, this works with Device Trees and ACPI and allows
device drivers to be written in a platform firmware (DT or ACPI)
agnostic way. The at25, leds-gpio and gpio_keys_polled drivers
are now going to use this new interface and the GPIO subsystem
is additionally modified to allow device drivers to assign names
to GPIO resources returned by ACPI _CRS objects (in case _DSD is
not present or does not provide the expected data). The changes
in this set are mostly from Mika Westerberg, Rafael J Wysocki,
Aaron Lu, and Darren Hart with some fixes from others (Fabio Estevam,
Geert Uytterhoeven).
- Support for Hardware Managed Performance States (HWP) as described
in Volume 3, section 14.4, of the Intel SDM in the intel_pstate
driver. CPUID is used to detect whether or not the feature is
supported by the processor. If supported, it will be enabled
automatically unless the intel_pstate=no_hwp switch is present in
the kernel command line. From Dirk Brandewie.
- New Intel Broadwell-H ID for intel_pstate (Dirk Brandewie).
- Support for firmware interface based on ACPI operation regions
used by the PMIC chips on the Intel Baytrail-T and Baytrail-T-CR
platforms for power resource control and thermal management
(Aaron Lu).
- Limited support for retrieving off-the-hierarchy dependencies
between devices from ACPI _DEP device configuration objects
and deferred probing support for the ACPI battery driver based
on the _DEP information to make that driver work on Asus T100A
(Lan Tianyu).
- New cpufreq driver for the Loongson1B processor (Kelvin Cheung).
- ACPICA update to upstream revision 20141107 which only affects
tools (Bob Moore).
- Fixes for race conditions in the ACPICA's interrupt handling
code and in the ACPI code related to system suspend and resume
(Lv Zheng and Rafael J Wysocki).
- ACPI core fix for an RCU-related issue in the ioremap() regions
management code that slowed down significantly after CPUs had
been allowed to enter idle states even if they'd had RCU callbakcs
queued and triggered some problems in certain proprietary graphics
driver (and elsewhere). The fix replaces synchronize_rcu() in
that code with synchronize_rcu_expedited() which makes the issue
go away. From Konstantin Khlebnikov.
- ACPI LPSS (Low-Power Subsystem) driver fix to handle power
management of the DMA engine included into the LPSS correctly.
The problem is that the DMA engine doesn't have ACPI PM support
of its own and it simply is turned off when the last LPSS device
having ACPI PM support goes into D3cold. To work around that,
the PM domain used by the ACPI LPSS driver is redesigned so at
least one device with ACPI PM support will be on as long as the
DMA engine is in use. From Andy Shevchenko.
- ACPI backlight driver fix to avoid using it on "Win8-compatible"
systems where it doesn't work and where it was used by default by
mistake (Aaron Lu).
- Assorted minor ACPI core fixes and cleanups from Tomasz Nowicki,
Sudeep Holla, Huang Rui, Hanjun Guo, Fabian Frederick, and
Ashwin Chaugule (mostly related to the upcoming ARM64 support).
- Intel RAPL (Running Average Power Limit) power capping driver
fixes and improvements including new processor IDs (Jacob Pan).
- Generic power domains modification to power up domains after
attaching devices to them to meet the expectations of device
drivers and bus types assuming devices to be accessible at
probe time (Ulf Hansson).
- Preliminary support for controlling device clocks from the
generic power domains core code and modifications of the
ARM/shmobile platform to use that feature (Ulf Hansson).
- Assorted minor fixes and cleanups of the generic power
domains core code (Ulf Hansson, Geert Uytterhoeven).
- Assorted minor fixes and cleanups of the device clocks control
code in the PM core (Geert Uytterhoeven, Grygorii Strashko).
- Consolidation of device power management Kconfig options by making
CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and removing the latter
which is now redundant (Rafael J Wysocki and Kevin Hilman). That
is the first batch of the changes needed for this purpose.
- Core device runtime power management support code cleanup related
to the execution of callbacks (Andrzej Hajda).
- cpuidle ARM support improvements (Lorenzo Pieralisi).
- cpuidle cleanup related to the CPUIDLE_FLAG_TIME_VALID flag and
a new MAINTAINERS entry for ARM Exynos cpuidle (Daniel Lezcano and
Bartlomiej Zolnierkiewicz).
- New cpufreq driver callback (->ready) to be executed when the
cpufreq core is ready to use a given policy object and cpufreq-dt
driver modification to use that callback for cooling device
registration (Viresh Kumar).
- cpufreq core fixes and cleanups (Viresh Kumar, Vince Hsu,
James Geboski, Tomeu Vizoso).
- Assorted fixes and cleanups in the cpufreq-pcc, intel_pstate,
cpufreq-dt, pxa2xx cpufreq drivers (Lenny Szubowicz, Ethan Zhao,
Stefan Wahren, Petr Cvek).
- OPP (Operating Performance Points) framework modification to
allow OPPs to be removed too and update of a few cpufreq drivers
(cpufreq-dt, exynos5440, imx6q, cpufreq) to remove OPPs (added
during initialization) on driver removal (Viresh Kumar).
- Hibernation core fixes and cleanups (Tina Ruchandani and
Markus Elfring).
- PM Kconfig fix related to CPU power management (Pankaj Dubey).
- cpupower tool fix (Prarit Bhargava).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=5dox
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"This time we have some more new material than we used to have during
the last couple of development cycles.
The most important part of it to me is the introduction of a unified
interface for accessing device properties provided by platform
firmware. It works with Device Trees and ACPI in a uniform way and
drivers using it need not worry about where the properties come from
as long as the platform firmware (either DT or ACPI) makes them
available. It covers both devices and "bare" device node objects
without struct device representation as that turns out to be necessary
in some cases. This has been in the works for quite a few months (and
development cycles) and has been approved by all of the relevant
maintainers.
On top of that, some drivers are switched over to the new interface
(at25, leds-gpio, gpio_keys_polled) and some additional changes are
made to the core GPIO subsystem to allow device drivers to manipulate
GPIOs in the "canonical" way on platforms that provide GPIO
information in their ACPI tables, but don't assign names to GPIO lines
(in which case the driver needs to do that on the basis of what it
knows about the device in question). That also has been approved by
the GPIO core maintainers and the rfkill driver is now going to use
it.
Second is support for hardware P-states in the intel_pstate driver.
It uses CPUID to detect whether or not the feature is supported by the
processor in which case it will be enabled by default. However, it
can be disabled entirely from the kernel command line if necessary.
Next is support for a platform firmware interface based on ACPI
operation regions used by the PMIC (Power Management Integrated
Circuit) chips on the Intel Baytrail-T and Baytrail-T-CR platforms.
That interface is used for manipulating power resources and for
thermal management: sensor temperature reporting, trip point setting
and so on.
Also the ACPI core is now going to support the _DEP configuration
information in a limited way. Basically, _DEP it supposed to reflect
off-the-hierarchy dependencies between devices which may be very
indirect, like when AML for one device accesses locations in an
operation region handled by another device's driver (usually, the
device depended on this way is a serial bus or GPIO controller). The
support added this time is sufficient to make the ACPI battery driver
work on Asus T100A, but it is general enough to be able to cover some
other use cases in the future.
Finally, we have a new cpufreq driver for the Loongson1B processor.
In addition to the above, there are fixes and cleanups all over the
place as usual and a traditional ACPICA update to a recent upstream
release.
As far as the fixes go, the ACPI LPSS (Low-power Subsystem) driver for
Intel platforms should be able to handle power management of the DMA
engine correctly, the cpufreq-dt driver should interact with the
thermal subsystem in a better way and the ACPI backlight driver should
handle some more corner cases, among other things.
On top of the ACPICA update there are fixes for race conditions in the
ACPICA's interrupt handling code which might lead to some random and
strange looking failures on some systems.
In the cleanups department the most visible part is the series of
commits targeted at getting rid of the CONFIG_PM_RUNTIME configuration
option. That was triggered by a discussion regarding the generic
power domains code during which we realized that trying to support
certain combinations of PM config options was painful and not really
worth it, because nobody would use them in production anyway. For
this reason, we decided to make CONFIG_PM_SLEEP select
CONFIG_PM_RUNTIME and that lead to the conclusion that the latter
became redundant and CONFIG_PM could be used instead of it. The
material here makes that replacement in a major part of the tree, but
there will be at least one more batch of that in the second part of
the merge window.
Specifics:
- Support for retrieving device properties information from ACPI _DSD
device configuration objects and a unified device properties
interface for device drivers (and subsystems) on top of that. As
stated above, this works with Device Trees and ACPI and allows
device drivers to be written in a platform firmware (DT or ACPI)
agnostic way. The at25, leds-gpio and gpio_keys_polled drivers are
now going to use this new interface and the GPIO subsystem is
additionally modified to allow device drivers to assign names to
GPIO resources returned by ACPI _CRS objects (in case _DSD is not
present or does not provide the expected data). The changes in
this set are mostly from Mika Westerberg, Rafael J Wysocki, Aaron
Lu, and Darren Hart with some fixes from others (Fabio Estevam,
Geert Uytterhoeven).
- Support for Hardware Managed Performance States (HWP) as described
in Volume 3, section 14.4, of the Intel SDM in the intel_pstate
driver. CPUID is used to detect whether or not the feature is
supported by the processor. If supported, it will be enabled
automatically unless the intel_pstate=no_hwp switch is present in
the kernel command line. From Dirk Brandewie.
- New Intel Broadwell-H ID for intel_pstate (Dirk Brandewie).
- Support for firmware interface based on ACPI operation regions used
by the PMIC chips on the Intel Baytrail-T and Baytrail-T-CR
platforms for power resource control and thermal management (Aaron
Lu).
- Limited support for retrieving off-the-hierarchy dependencies
between devices from ACPI _DEP device configuration objects and
deferred probing support for the ACPI battery driver based on the
_DEP information to make that driver work on Asus T100A (Lan
Tianyu).
- New cpufreq driver for the Loongson1B processor (Kelvin Cheung).
- ACPICA update to upstream revision 20141107 which only affects
tools (Bob Moore).
- Fixes for race conditions in the ACPICA's interrupt handling code
and in the ACPI code related to system suspend and resume (Lv Zheng
and Rafael J Wysocki).
- ACPI core fix for an RCU-related issue in the ioremap() regions
management code that slowed down significantly after CPUs had been
allowed to enter idle states even if they'd had RCU callbakcs
queued and triggered some problems in certain proprietary graphics
driver (and elsewhere). The fix replaces synchronize_rcu() in that
code with synchronize_rcu_expedited() which makes the issue go
away. From Konstantin Khlebnikov.
- ACPI LPSS (Low-Power Subsystem) driver fix to handle power
management of the DMA engine included into the LPSS correctly. The
problem is that the DMA engine doesn't have ACPI PM support of its
own and it simply is turned off when the last LPSS device having
ACPI PM support goes into D3cold. To work around that, the PM
domain used by the ACPI LPSS driver is redesigned so at least one
device with ACPI PM support will be on as long as the DMA engine is
in use. From Andy Shevchenko.
- ACPI backlight driver fix to avoid using it on "Win8-compatible"
systems where it doesn't work and where it was used by default by
mistake (Aaron Lu).
- Assorted minor ACPI core fixes and cleanups from Tomasz Nowicki,
Sudeep Holla, Huang Rui, Hanjun Guo, Fabian Frederick, and Ashwin
Chaugule (mostly related to the upcoming ARM64 support).
- Intel RAPL (Running Average Power Limit) power capping driver fixes
and improvements including new processor IDs (Jacob Pan).
- Generic power domains modification to power up domains after
attaching devices to them to meet the expectations of device
drivers and bus types assuming devices to be accessible at probe
time (Ulf Hansson).
- Preliminary support for controlling device clocks from the generic
power domains core code and modifications of the ARM/shmobile
platform to use that feature (Ulf Hansson).
- Assorted minor fixes and cleanups of the generic power domains core
code (Ulf Hansson, Geert Uytterhoeven).
- Assorted minor fixes and cleanups of the device clocks control code
in the PM core (Geert Uytterhoeven, Grygorii Strashko).
- Consolidation of device power management Kconfig options by making
CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and removing the latter
which is now redundant (Rafael J Wysocki and Kevin Hilman). That
is the first batch of the changes needed for this purpose.
- Core device runtime power management support code cleanup related
to the execution of callbacks (Andrzej Hajda).
- cpuidle ARM support improvements (Lorenzo Pieralisi).
- cpuidle cleanup related to the CPUIDLE_FLAG_TIME_VALID flag and a
new MAINTAINERS entry for ARM Exynos cpuidle (Daniel Lezcano and
Bartlomiej Zolnierkiewicz).
- New cpufreq driver callback (->ready) to be executed when the
cpufreq core is ready to use a given policy object and cpufreq-dt
driver modification to use that callback for cooling device
registration (Viresh Kumar).
- cpufreq core fixes and cleanups (Viresh Kumar, Vince Hsu, James
Geboski, Tomeu Vizoso).
- Assorted fixes and cleanups in the cpufreq-pcc, intel_pstate,
cpufreq-dt, pxa2xx cpufreq drivers (Lenny Szubowicz, Ethan Zhao,
Stefan Wahren, Petr Cvek).
- OPP (Operating Performance Points) framework modification to allow
OPPs to be removed too and update of a few cpufreq drivers
(cpufreq-dt, exynos5440, imx6q, cpufreq) to remove OPPs (added
during initialization) on driver removal (Viresh Kumar).
- Hibernation core fixes and cleanups (Tina Ruchandani and Markus
Elfring).
- PM Kconfig fix related to CPU power management (Pankaj Dubey).
- cpupower tool fix (Prarit Bhargava)"
* tag 'pm+acpi-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (120 commits)
i2c-omap / PM: Drop CONFIG_PM_RUNTIME from i2c-omap.c
dmaengine / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
tools: cpupower: fix return checks for sysfs_get_idlestate_count()
drivers: sh / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
e1000e / igb / PM: Eliminate CONFIG_PM_RUNTIME
MMC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
MFD / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
misc / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
media / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
input / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
leds: leds-gpio: Fix multiple instances registration without 'label' property
iio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
hsi / OMAP / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
i2c-hid / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
drm / exynos / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
gpio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
hwrandom / exynos / PM: Use CONFIG_PM in #ifdef
block / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
USB / PM: Drop CONFIG_PM_RUNTIME from the USB core
PM: Merge the SET*_RUNTIME_PM_OPS() macros
...
If a HID descriptor places HID_DG_CONTACTID before HID_DG_X and HID_DG_Y then
the ABS_X and ABS_Y will not be automatically initialized by the call to
input_mt_init_slots. To ensure that this is not a problem, we relocate that
call to occur after HID parsing has been completed and we've initalized all the
multitouch axes.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Defined outbound offset for DTU and Cintiq. But didn't update
the relevant maximum values. Oops...
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
After commit b2b49ccbdd (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so #ifdef blocks
depending on CONFIG_PM_RUNTIME may now be changed to depend on
CONFIG_PM.
Replace CONFIG_PM_RUNTIME with CONFIG_PM in drivers/hid/i2c-hid/i2c-hid.c.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
There are screen to tablet offsets for newer Cintiq and DTU models.
These offsets serve as outbound tracking for those display tablets.
Use defines instead of hardcoded numbers for the offsets.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Since the conversion from USB to HID (in v3.17), some people reported a
freeze on boot with the wacom driver. Hans managed to get a stacktrace:
[ 240.272331] Call Trace:
[ 240.272338] [<ffffffff813de7b9>] ? usb_hcd_submit_urb+0xa9/0xb10
[ 240.272347] [<ffffffff81555579>] schedule+0x29/0x70
[ 240.272355] [<ffffffff815559e6>] schedule_preempt_disabled+0x16/0x20
[ 240.272363] [<ffffffff81557365>] __mutex_lock_slowpath+0xe5/0x230
[ 240.272372] [<ffffffff815574c7>] mutex_lock+0x17/0x30
[ 240.272380] [<ffffffffa063c1d2>] wacom_resume+0x22/0x50 [wacom]
[ 240.272396] [<ffffffffa01aea8a>] hid_resume_common+0xba/0x110 [usbhid]
[ 240.272404] [<ffffffff813e5890>] ? usb_runtime_suspend+0x80/0x80
[ 240.272417] [<ffffffffa01aeb1d>] hid_resume+0x3d/0x70 [usbhid]
[ 240.272425] [<ffffffff813e44a6>] usb_resume_interface.isra.6+0xb6/0x120
[ 240.272432] [<ffffffff813e4774>] usb_resume_both+0x74/0x140
[ 240.272439] [<ffffffff813e58aa>] usb_runtime_resume+0x1a/0x20
[ 240.272446] [<ffffffff813b1912>] __rpm_callback+0x32/0x70
[ 240.272453] [<ffffffff813b1976>] rpm_callback+0x26/0xa0
[ 240.272460] [<ffffffff813b2d71>] rpm_resume+0x4b1/0x690
[ 240.272468] [<ffffffff812ab992>] ? radix_tree_lookup_slot+0x22/0x50
[ 240.272475] [<ffffffff813b2c1a>] rpm_resume+0x35a/0x690
[ 240.272482] [<ffffffff8116e9c9>] ? zone_statistics+0x89/0xa0
[ 240.272489] [<ffffffff813b2f90>] __pm_runtime_resume+0x40/0x60
[ 240.272497] [<ffffffff813e4272>] usb_autopm_get_interface+0x22/0x60
[ 240.272509] [<ffffffffa01ae8d9>] usbhid_open+0x59/0xe0 [usbhid]
[ 240.272517] [<ffffffffa063ac85>] wacom_open+0x35/0x50 [wacom]
[ 240.272525] [<ffffffff813f37b9>] input_open_device+0x79/0xa0
[ 240.272534] [<ffffffffa048d1c1>] evdev_open+0x1b1/0x200 [evdev]
[ 240.272543] [<ffffffff811c899e>] chrdev_open+0xae/0x1f0
[ 240.272549] [<ffffffff811c88f0>] ? cdev_put+0x30/0x30
[ 240.272556] [<ffffffff811c17e2>] do_dentry_open+0x1d2/0x320
[ 240.272562] [<ffffffff811c1cd1>] finish_open+0x31/0x50
[ 240.272571] [<ffffffff811d2202>] do_last.isra.36+0x652/0xe50
[ 240.272579] [<ffffffff811d2ac7>] path_openat+0xc7/0x6f0
[ 240.272586] [<ffffffff811cf012>] ? final_putname+0x22/0x50
[ 240.272594] [<ffffffff811d42d2>] ? user_path_at_empty+0x72/0xd0
[ 240.272602] [<ffffffff811d43fd>] do_filp_open+0x4d/0xc0
[...]
So here, wacom_open is called, and then wacom_resume is called by the
PM system. However, wacom_open already took the lock when wacom_resume
tries to get it. Freeze.
A little bit of history shows that this already happened in the past
- commit f6cd378372 ("Input: wacom - fix runtime PM related deadlock"),
and the solution was to call first the PM function before taking the lock.
The lock was introduced in commit commit e722409445 ("Input: wacom -
implement suspend and autosuspend") when the autosuspend feature has
been added. Given that usbhid already takes care of this very same
locking between suspend/resume, I think we can simply kill the lock
in open/close.
The lock is now used also with LEDs, so we can not remove it completely.
Reported-by: Hans Spath <inbox-546@hans-spath.de>
Tested-by: Hans Spath <inbox-546@hans-spath.de>
CC: stable@vger.kernel.org # v3.17+
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
In several hid drivers it is necessary to calculate the length of an
hid_report. This patch exports the existing static function hid_report_len of
hid-core.c as an inline function in hid.h
Signed-off-by: Mathieu Magnaudet <mathieu.magnaudet@enac.fr>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
It is not necessarily sufficient to look only at the physical and logical
usages when determining if a field is for the pen or touch. Some fields
are not contained in a sub-collection and thus only have an application
usage. Not checking the application usage in such cases causes us to
ignore the field entirely, which may lead to incorrect behavior.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
PAD can be on pen interface (Intuos Pro and Cintiq series) or touch
interface (Bamboo PT and Intuos PT series) or its own interface
(Bamboo pen-only and Intuos Pen M/S). We need to mark it independently.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Use mfd_add_hotplug_devices() helper to register the subdevices.
Compile-only tested.
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
VTL panels do not switch to the multitouch mode until the input mode
feature is read by the host. This should normally be done by
usbhid, but it looks like an other bug prevents usbhid to properly
retrieve the feature state. As a workaround, we force the reading of
the feature in mt_set_input_mode for such devices.
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Mathieu Magnaudet <mathieu.magnaudet@enac.fr>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Current driver uses a common buffer for reading reports either
synchronously in i2c_hid_get_raw_report() and asynchronously in
the interrupt handler.
There is race condition if an interrupt arrives immediately after
the report is received in i2c_hid_get_raw_report(); the common
buffer is modified by the interrupt handler with the new report
and then i2c_hid_get_raw_report() proceed using wrong data.
Fix it by using a separate buffers for synchronous reports.
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
[Antonio Borneo: cleanup, rebase to v3.17, submit mainline]
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Provide the resolution of several angular axes (tilt, pen rotation, puck
rotation) to userspace. Because these values are natively degree-based, we
need to convert them to into units/radian as required by the input_absinfo
struct. To ensure wraparound behaves properly for the rotation axes, the
converted value was rounded up rather than rounded nearest.
Notably, the touchring axes (ABS_WHEEL and ABS_THROTTLE) are left without a
a declared resolution because the their low resolution cannot be accurately
represented (the worst-case rounding-induced error would be ~16 degrees).
Pre-scaling the values and range by at least 10x would reduce the error in
the resolution to acceptable levels, but the xf86-input-wacom driver is not
able to use pre-scaled values for these axes at this time.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Centers the ABS_TILT_{X,Y} axes so that a value of zero is reported when
the pen is vertical. Combined with resolution information in the next
patch, this makes it possible for userspace to calculate the pen angle
without needing hardware-specific knowledge. The xf86-input-wacom driver
was updated to support signed tilt values in late-2012 (2f2acec).
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Bamboo models do not support HID_DG_CONTACTMAX. Plus, Bamboo pen-only
has touch descriptor. This leads to some complications in the code.
This patch also fixes duplicated PAD interfeaces for Intuos Pen
models.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Graphire 4 only has two tablet buttons; Bamboo Fun touch ring is only
for PAD.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
ENODEV indicates no device is added. Hence, the associated pad input device
is simply freed.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add vid/pid for the SMK branded third-party PS3 Bluetooth remote and enable
support in the hid-sony driver.
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The touchscreen needs the same quirk as the other models.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Reported-by: Bryan Poling <poli0048@umn.edu>
CC: stable@vger.kernel.org
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Replace stack buffers with kernel allocated buffers for sending
and receiving HID reports to prevent issues with DMA transfers
on certain hardware.
Output report buffers are allocated at initialization time to avoid
excessive calls to kmalloc and kfree.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=87991
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Report is received in "buffer"; fix the following i2c_hid_dbg()
to dump data from the correct pointer.
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
[Antonio Borneo: cleanup and rebase to v3.17]
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Pull HID fixes from Jiri Kosina:
- fix for an oops in HID core upon repeated subdriver insertion/removal
under certain circumstances, by Benjamin Tissoires
- quirk for another Elan Touchscreen device, by Adel Gadllah
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: core: cleanup .claimed field on disconnect
HID: usbhid: enable always-poll quirk for Elan Touchscreen 0103
On the USB keyboard, the VENDOR hotkeys share the same device as the
mouse. Setting EV_REP also affects mouse buttons, so leave it off.
The bluetooth keyboard still has autorepeating mouse buttons, as it
only has one device and is set by the KEYBOARD pages.
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The bluetooth keyboard also generates 0x00fa when the middle button is
pressed. Move the made-up report out of the way so we don't trigger
KEY_FILE when middle button is pressed
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
touch_input is stored in wacom_shared for pen data to report touch
switch status. It is possible, although we didn't see it happen on
Linux yet, that pen data is procesed before touch interface is
fully probed.
As a by-product of this patch, it fixes the FreeBSD issue reported
by Denis Akiyakov http://www.spinics.net/lists/linux-input/msg33971.html
Reviewed-by: Hans Petter Selasky <hps@selasky.org>
Tested-by: Denis Akiyakov <d.akiyakov@gmail.com>
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
I have tested HID quirk for Saitek R.A.T.7 with my R.A.T. 9. It works fine for
me. Attached patch makes the necessary changes to use the quirk on the R.A.T.9
too, and necessary Kconfig changes too.
I have stylized the Kconfig option name to include Mad Catz in the option name,
as (at least some of) the devices are marketed under Mad Catz brand.
Signed-off-by: Ville Aakko <ville.aakko@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
- remove the constant '1'
- when the device is not connected, the protocol error
HIDPP_ERROR_RESOURCE_ERROR is raised. We should not warn the user about
it because it is somewhat expected as an answer when we check if the
device is connected.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
