Currently we directly call a clock_enable in trigger function without
a clk_prepare as pair first.
This will cause system hang immediately when run capture because
the clock was not prepared(playback does not hang because the clock was
prepared already by get_mclk before), a warning message in clock framework
may cause a deadlock to reclaim clock lock (see: pl011_console_write).
Here we prepare clock first in hw_param, then enable it in trigger
function to guarantee the balance.
Signed-off-by: Dong Aisheng <dong.aisheng@linaro.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Otherwise if someone tries to use all four channels on AIF1 with the
device in master mode we won't be able to clock out all the data.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
Ever since the DAPM performance improvements we've been marking all widgets
as not dirty after each DAPM run. Since _PRE and _POST events aren't part
of the DAPM graph this has rendered them non-functional, they will never be
marked dirty again and thus will never be run again.
Fix this by skipping them when marking widgets as not dirty.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Cc: stable@vger.kernel.org
The MX31 Audmux also has 7 Ports.
This patch adds the missing define, and makes the debugfs code iterate
over that port too.
Signed-off-by: Torben Hohn <torbenh@linutronix.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The conversion of the core driver to irqdomains means that we don't need
and irq_base to have working interrupts so use wm8994_request_irq() to
deal with looking up the interrupt number for the micdet IRQ.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The s3c2410_gpio* calls are obsolete and have been scheduled for
removal since several kernel releases. Remove them and use common
gpiolib API.
This patch is a prerequisite for removal of the obsolete S3C24XX
SoC GPIO definitions.
Compile tested only.
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The s3c2410_gpio* calls are obsolete and have been scheduled for
removal since several kernel releases. Remove them and use common
gpiolib API.
This patch is a prerequisite for removal of the obsolete S3C24XX
SoC GPIO definitions.
Tested on Micro2440-SDK.
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix following:
sound/soc/soc-dapm.c: In function ‘dapm_clock_event’:
sound/soc/soc-dapm.c:1021:1: warning: control reaches end of non-void function [-Wreturn-type]
Signed-off-by: Marek Belisko <marek.belisko@open-nandra.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Ensure robust startup of the part by going through the reset procedure
prior to resyncing the full register cache, avoiding potential intermittent
faults in some designs.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
Release the memory of the routing table before leaving the function upon errors
in the device tree
Signed-off-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM5110 is a highly integrated low power audio subsystem for
smartphones, tablets and other portable audio devices. It combines
an advanced DSP feature set with a flexible, high performance audio
hub CODEC.
This patch adds the audio CODEC driver for the device.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
GCC complains that "ret" is uninitialized here.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-By: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Some Arizona chips have a higher frequency for the FLL VCO, support this
in the common code.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds input selection of main codec clock - from what pin.
Both registers set same value since codec uses clock divider or pll at one time.
Signed-off-by: Jiri Prchal <jiri.prchal@aksignal.cz>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds AGC target level and times settings for TLV320AIC3x.
Enums uses small arrays of two channels left and right since it uses different registers.
Signed-off-by: Jiri Prchal <jiri.prchal@aksignal.cz>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds missing deemphasis switch.
Signed-off-by: Jiri Prchal <jiri.prchal@aksignal.cz>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The analogue PGA shifts were used; this makes no practical difference as
the values are the same.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The MODULE_ALIAS() was missing from the driver.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Since we're now relying on DAPM for things like enabling clocks when we
reparent the clocks for widgets we need to either use conditional routes
(which are expensive) or remove routes at runtime. Add a route removal
API to support this use case.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
If we add a new route at runtime then we'll need to recheck the connections
to the affected widgets.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Some userspace will open a PCM device and then configure mixers
for routing before triggering. This patch allows userspace to do
this sequence.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix spelling mistake in "High-Performance" option of twl6040 power mode.
Signed-off-by: Simon Wilson <simonwilson@google.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Make sure we set the bias level for all DAPM contexts when
changing level.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use dev_ style logging throughout soc_new_pcm()
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Codec shutdown performs a DAPM power sequence that might cause conflicts
and/or race conditions if another stream power event is running simultaneously.
Use card's dapm mutex to protect any potential race condition between them.
Signed-off-by: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
If an audio interface is configured to use ASYNCCLK then update the
asynchronous sample rate rather than one of our primary sample rates.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
mx27pdk board also has a mc13783 codec.
Add support for it and do a run-time machine type check to perform the correct
audiomux settings.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If we don't set IMX_AUDMUX_V2_PTCR_TCLKDIR in the AUDMUX PTCR
register (means Tx clock pin is input), we don't need to set
IMX_AUDMUX_V2_PTCR_TCSEL as well. Since both i.MX35, i.MX51 and
i.MX6 datasheet says "When Tx clock pin set as an input, the TCSEL
settings are ignored".
Signed-off-by: Hui Wang <jason77.wang@gmail.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Allow any BCLK which can be divided down to generate LRCLK, not just the
lowest possible BCLK to clock out the samples.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Allow the user to select which of the system clocks each AIF is referenced
to and constran the DAI to the set of frequencies which can be generated
from that clock.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
They're the rates for the BCLK, not for the sample rate, so rename so that
we don't confuse ourselves.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch implements the spdif out driver for ST peripheral. This
peripheral implements IEC60958 standard
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The STA529 is a digital stereo class-D audio amplifier. It includes an
audio DSP, an ST proprietary high-efficiency class-D driver and CMOS
power output stage. It is intended for high-efficiency
digital-to-power-audio conversion for portable applications.
Signed-off-by: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Adds missing register default values to cache.
Signed-off-by: Jiri Prchal <jiri.prchal@aksignal.cz>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Adds register and bit shift definitions in header file.
Changes are for TLV320AIC310x based on data sheet.
Signed-off-by: Jiri Prchal <jiri.prchal@aksignal.cz>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Leave it up to the machine driver to disable accessory detection if
desired, the common pattern is to have accessory detection be a wake
source.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Since most new drivers are expected to use regmap and since frequently the
only thing we need to do in the CODEC probe function is configure the I/O
try to initialise the register I/O using regmap if the driver hasn't done
so after probe().
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
dapm_set_path_status() sets connect incorrectly in the case max > 1 with invert.
In that case, the raw disconnect value should be max, which corresponds to the
userspace value 0.
This use case currently does not appear upstream, but it could break
SOC_DAPM_SINGLE() or SOC_DAPM_SINGLE_TLV() elsewhere or in the future.
This patch completes commit 3a9abe8.
Cc: Liam Girdwood <lrg@ti.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: <alsa-devel@alsa-project.org>
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use the dmaengine based Tegra APB DMA driver for
data transfer between SPI fifo and memory in
place of legacy Tegra APB DMA.
Because generic soc-dmaengine-pcm uses the DMAs API
based on dmaengine, using the exported APIs provided
by this generic driver.
The new driver is selected if legacy driver is not
selected and new dma driver is enabled through config
file.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Stereo is not yet supported by dapm widgets, so remove stereo code from
snd_soc_dapm_get_volsw(), and warn if stereo controls are detected.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Current method for machine driver to register with the ASoC core is to use
snd_soc_register_card() instead of creating a "soc-audio" platform device.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
