Turns out some xHC controllers require all 64 bits in the CRCR register
to be written to execute a command abort.
The lower 32 bits containing the command abort bit is written first.
In case the command ring stops before we write the upper 32 bits then
hardware may use these upper bits to set the commnd ring dequeue pointer.
Solve this by making sure the upper 32 bits contain a valid command
ring dequeue pointer.
The original patch that only wrote the first 32 to stop the ring went
to stable, so this fix should go there as well.
Fixes: ff0e50d356 ("xhci: Fix command ring pointer corruption while aborting a command")
Cc: stable@vger.kernel.org
Tested-by: Pavankumar Kondeti <quic_pkondeti@quicinc.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20211126122340.1193239-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The trampoline_pgd only maps the 0xfffffff000000000-0xffffffffffffffff
range of kernel memory (with 4-level paging). This range contains the
kernel's text+data+bss mappings and the module mapping space but not the
direct mapping and the vmalloc area.
This is enough to get the application processors out of real-mode, but
for code that switches back to real-mode the trampoline_pgd is missing
important parts of the address space. For example, consider this code
from arch/x86/kernel/reboot.c, function machine_real_restart() for a
64-bit kernel:
#ifdef CONFIG_X86_32
load_cr3(initial_page_table);
#else
write_cr3(real_mode_header->trampoline_pgd);
/* Exiting long mode will fail if CR4.PCIDE is set. */
if (boot_cpu_has(X86_FEATURE_PCID))
cr4_clear_bits(X86_CR4_PCIDE);
#endif
/* Jump to the identity-mapped low memory code */
#ifdef CONFIG_X86_32
asm volatile("jmpl *%0" : :
"rm" (real_mode_header->machine_real_restart_asm),
"a" (type));
#else
asm volatile("ljmpl *%0" : :
"m" (real_mode_header->machine_real_restart_asm),
"D" (type));
#endif
The code switches to the trampoline_pgd, which unmaps the direct mapping
and also the kernel stack. The call to cr4_clear_bits() will find no
stack and crash the machine. The real_mode_header pointer below points
into the direct mapping, and dereferencing it also causes a crash.
The reason this does not crash always is only that kernel mappings are
global and the CR3 switch does not flush those mappings. But if theses
mappings are not in the TLB already, the above code will crash before it
can jump to the real-mode stub.
Extend the trampoline_pgd to contain all kernel mappings to prevent
these crashes and to make code which runs on this page-table more
robust.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20211202153226.22946-5-joro@8bytes.org
Boris reported that in one of his randconfig builds, objtool got
infinitely stuck. Turns out there's trivial list corruption in the
pv_ops tracking when a function is both in a static table and in a code
assignment.
Avoid re-adding function to the pv_ops[] lists when they're already on
it.
Fixes: db2b0c5d7b ("objtool: Support pv_opsindirect calls for noinstr")
Reported-by: Borislav Petkov <bp@alien8.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Borislav Petkov <bp@suse.de>
Tested-by: Borislav Petkov <bp@alien8.de>
Link: https://lkml.kernel.org/r/20211202204534.GA16608@worktop.programming.kicks-ass.net
drm fixes for 5.16-rc4
dma-buf:
- memory leak fix
msm:
- kasan found memory overwrite
- mmap flags
- fencing error bug
- ioctl NULL ptr
- uninit var
- devfreqless devices fix
- dsi lanes fix
- dp: avoid unpowered aux xfers
amdgpu:
- IP discovery based enumeration fixes
- vkms fixes
- DSC fixes for DP MST
- Audio fix for hotplug with tiled displays
- Misc display fixes
- DP tunneling fix
- DP fix
- Aldebaran fix
amdkfd:
- Locking fix
- Static checker fix
- Fix double free
i915:
- backlight regression
- Intel HDR backlight detection fix
- revert TGL workaround that caused hangs
virtio-gpu:
- switch back to drm_poll
vc4:
- memory leak
- error check fix
- HVS modesetting fixes
-----BEGIN PGP SIGNATURE-----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=xcZd
-----END PGP SIGNATURE-----
Merge tag 'drm-fixes-2021-12-03-1' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"Bit of an uptick in patch count this week, though it's all relatively
small overall.
I suspect msm has been queuing up a few fixes to skew it here.
Otherwise amdgpu has a scattered bunch of small fixes, and then some
vc4, i915.
virtio-gpu changes an rc1 introduced uAPI mistake, and makes it
operate more like other drivers. This should be fine as no userspace
relies on the behaviour yet.
Summary:
dma-buf:
- memory leak fix
msm:
- kasan found memory overwrite
- mmap flags
- fencing error bug
- ioctl NULL ptr
- uninit var
- devfreqless devices fix
- dsi lanes fix
- dp: avoid unpowered aux xfers
amdgpu:
- IP discovery based enumeration fixes
- vkms fixes
- DSC fixes for DP MST
- Audio fix for hotplug with tiled displays
- Misc display fixes
- DP tunneling fix
- DP fix
- Aldebaran fix
amdkfd:
- Locking fix
- Static checker fix
- Fix double free
i915:
- backlight regression
- Intel HDR backlight detection fix
- revert TGL workaround that caused hangs
virtio-gpu:
- switch back to drm_poll
vc4:
- memory leak
- error check fix
- HVS modesetting fixes"
* tag 'drm-fixes-2021-12-03-1' of git://anongit.freedesktop.org/drm/drm: (41 commits)
Revert "drm/i915: Implement Wa_1508744258"
drm/amdkfd: process_info lock not needed for svm
drm/amdgpu: adjust the kfd reset sequence in reset sriov function
drm/amd/display: add connector type check for CRC source set
drm/amdkfd: fix double free mem structure
drm/amdkfd: set "r = 0" explicitly before goto
drm/amd/display: Add work around for tunneled MST.
drm/amd/display: Fix for the no Audio bug with Tiled Displays
drm/amd/display: Clear DPCD lane settings after repeater training
drm/amd/display: Allow DSC on supported MST branch devices
drm/amdgpu: Don't halt RLC on GFX suspend
drm/amdgpu: fix the missed handling for SDMA2 and SDMA3
drm/amdgpu: check atomic flag to differeniate with legacy path
drm/amdgpu: cancel the correct hrtimer on exit
drm/amdgpu/sriov/vcn: add new vcn ip revision check case for SIENNA_CICHLID
drm/i915/dp: Perform 30ms delay after source OUI write
dma-buf: system_heap: Use 'for_each_sgtable_sg' in pages free flow
drm/i915: Add support for panels with VESA backlights with PWM enable/disable
drm/vc4: kms: Fix previous HVS commit wait
drm/vc4: kms: Don't duplicate pending commit
...
- Fix the Intel HDR backlight support detection.
- Reverting a w/a to fix a gpu Hang in TGL. The w/a itself was also
for a hang, but in a much rarer scenario. The proper solution need
to be done with help from user space and it will be addressed later.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEbSBwaO7dZQkcLOKj+mJfZA7rE8oFAmGpH+kACgkQ+mJfZA7r
E8p8ngf/U04CSeEqzS8PJ3U7NnOAIChv8IAgZQcMECZMl9vqU39mqoCRnTJHU0pS
dHF2xqPGeMBtKxs0hohM5ZVEsk/V1UnDOXvOYeKGHqUqkpZelCM5uzY3aVEXQJy2
Es2QmWfIE0RSvRKZZEMbhJN3AVayJ8nWwL1hO7sVwERm9aFBb2Dyti5973ntZRsO
FjJ5CRABMLhKtsT6Jrniv+TNPEOpkaELWml6ZwPn6JGRY8afCw0Q993gDozck90t
dcTmZ0uNYKbDvzxu/IAXiN1jw65QlvV33bGc7dPn6Dn0Y6Fo/0+WBQyerpB65Jn+
GMGKcZ/P9eZSf3V36gYKru5SYVneqg==
=5u4d
-----END PGP SIGNATURE-----
Merge tag 'drm-intel-fixes-2021-12-02' of git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
- Fixing a regression where the backlight brightness control stopped working.
- Fix the Intel HDR backlight support detection.
- Reverting a w/a to fix a gpu Hang in TGL. The w/a itself was also
for a hang, but in a much rarer scenario. The proper solution need
to be done with help from user space and it will be addressed later.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/Yakf9hdnR5or+zNP@intel.com
improper error check, some functional fixes too) for vc4, memory leak
fix in dma-buf,
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCYaiHXQAKCRDj7w1vZxhR
xcU2AQCjblCn6Qkj9gf3LBuO0npYaCrXQyNoGsb9e7wYWuHjZwD/dWUDQ2G9SY1a
d1UfF5Dr/4+8CXFv4EkAxNC32k/R9gI=
=NQ3M
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-fixes-2021-12-02' of git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
Switch back to drm_poll for virtio, multiple fixes (memory leak,
improper error check, some functional fixes too) for vc4, memory leak
fix in dma-buf,
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20211202084440.u3b7lbeulj7k3ltg@houat
and wireguard.
Current release - regressions:
- smc: keep smc_close_final()'s error code during active close
Current release - new code bugs:
- iwlwifi: various static checker fixes (int overflow, leaks, missing
error codes)
- rtw89: fix size of firmware header before transfer, avoid crash
- mt76: fix timestamp check in tx_status; fix pktid leak;
- mscc: ocelot: fix missing unlock on error in ocelot_hwstamp_set()
Previous releases - regressions:
- smc: fix list corruption in smc_lgr_cleanup_early
- ipv4: convert fib_num_tclassid_users to atomic_t
Previous releases - always broken:
- tls: fix authentication failure in CCM mode
- vrf: reset IPCB/IP6CB when processing outbound pkts, prevent
incorrect processing
- dsa: mv88e6xxx: fixes for various device errata
- rds: correct socket tunable error in rds_tcp_tune()
- ipv6: fix memory leak in fib6_rule_suppress
- wireguard: reset peer src endpoint when netns exits
- wireguard: improve resilience to DoS around incoming handshakes
- tcp: fix page frag corruption on page fault which involves TCP
- mpls: fix missing attributes in delete notifications
- mt7915: fix NULL pointer dereference with ad-hoc mode
Misc:
- rt2x00: be more lenient about EPROTO errors during start
- mlx4_en: update reported link modes for 1/10G
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=r0Jh
-----END PGP SIGNATURE-----
Merge tag 'net-5.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from wireless, and wireguard.
Mostly scattered driver changes this week, with one big clump in
mv88e6xxx. Nothing of note, really.
Current release - regressions:
- smc: keep smc_close_final()'s error code during active close
Current release - new code bugs:
- iwlwifi: various static checker fixes (int overflow, leaks, missing
error codes)
- rtw89: fix size of firmware header before transfer, avoid crash
- mt76: fix timestamp check in tx_status; fix pktid leak;
- mscc: ocelot: fix missing unlock on error in ocelot_hwstamp_set()
Previous releases - regressions:
- smc: fix list corruption in smc_lgr_cleanup_early
- ipv4: convert fib_num_tclassid_users to atomic_t
Previous releases - always broken:
- tls: fix authentication failure in CCM mode
- vrf: reset IPCB/IP6CB when processing outbound pkts, prevent
incorrect processing
- dsa: mv88e6xxx: fixes for various device errata
- rds: correct socket tunable error in rds_tcp_tune()
- ipv6: fix memory leak in fib6_rule_suppress
- wireguard: reset peer src endpoint when netns exits
- wireguard: improve resilience to DoS around incoming handshakes
- tcp: fix page frag corruption on page fault which involves TCP
- mpls: fix missing attributes in delete notifications
- mt7915: fix NULL pointer dereference with ad-hoc mode
Misc:
- rt2x00: be more lenient about EPROTO errors during start
- mlx4_en: update reported link modes for 1/10G"
* tag 'net-5.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (85 commits)
net: dsa: b53: Add SPI ID table
gro: Fix inconsistent indenting
selftests: net: Correct case name
net/rds: correct socket tunable error in rds_tcp_tune()
mctp: Don't let RTM_DELROUTE delete local routes
net/smc: Keep smc_close_final rc during active close
ibmvnic: drop bad optimization in reuse_tx_pools()
ibmvnic: drop bad optimization in reuse_rx_pools()
net/smc: fix wrong list_del in smc_lgr_cleanup_early
Fix Comment of ETH_P_802_3_MIN
ethernet: aquantia: Try MAC address from device tree
ipv4: convert fib_num_tclassid_users to atomic_t
net: avoid uninit-value from tcp_conn_request
net: annotate data-races on txq->xmit_lock_owner
octeontx2-af: Fix a memleak bug in rvu_mbox_init()
net/mlx4_en: Fix an use-after-free bug in mlx4_en_try_alloc_resources()
vrf: Reset IPCB/IP6CB when processing outbound pkts in vrf dev xmit
net: qlogic: qlcnic: Fix a NULL pointer dereference in qlcnic_83xx_add_rings()
net: dsa: mv88e6xxx: Link in pcs_get_state() if AN is bypassed
net: dsa: mv88e6xxx: Fix inband AN for 2500base-x on 88E6393X family
...
- Allow compares of strings when using signed and unsigned characters
- Fix kmemleak false positive for histogram entries.
- Handle negative numbers for user defined kretprobe data sizes
-----BEGIN PGP SIGNATURE-----
iIoEABYIADIWIQRRSw7ePDh/lE+zeZMp5XQQmuv6qgUCYagqyxQccm9zdGVkdEBn
b29kbWlzLm9yZwAKCRAp5XQQmuv6qlCuAP45eI+DN2P+HxlnuWq7bLt/HYcOucit
nALTZ4OIux8kqgEAss4wSTcUIefOQHi3PiMXgJmyXheTbeBUk/ecInDoZAQ=
=P6C/
-----END PGP SIGNATURE-----
Merge tag 'trace-v5.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
"Three tracing fixes:
- Allow compares of strings when using signed and unsigned characters
- Fix kmemleak false positive for histogram entries
- Handle negative numbers for user defined kretprobe data sizes"
* tag 'trace-v5.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
kprobes: Limit max data_size of the kretprobe instances
tracing: Fix a kmemleak false positive in tracing_map
tracing/histograms: String compares should not care about signed values
Some changes that went in 5.16 that had issues. When working on the
design a piece was redesigned and things got missed. And the message
type was not being initialized when it was allocated, resulting in some
crashes.
In addition, the IPMI driver has had a shutdown issue where it could
still have an item in a system workqueue after it had been shutdown.
Move to a private workqueue to avoid that problem.
-----BEGIN PGP SIGNATURE-----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=dPMY
-----END PGP SIGNATURE-----
Merge tag 'for-linus-5.16-2' of git://github.com/cminyard/linux-ipmi
Pull IPMI fixes from Corey Minyard:
"Some changes that went in 5.16 had issues. When working on the design
a piece was redesigned and things got missed. And the message type was
not being initialized when it was allocated, resulting in crashes.
In addition, the IPMI driver has had a shutdown issue where it could
still have an item in a system workqueue after it had been shutdown.
Move to a private workqueue to avoid that problem"
* tag 'for-linus-5.16-2' of git://github.com/cminyard/linux-ipmi:
ipmi:ipmb: Fix unknown command response
ipmi: fix IPMI_SMI_MSG_TYPE_IPMB_DIRECT response length checking
ipmi: fix oob access due to uninit smi_msg type
ipmi: msghandler: Make symbol 'remove_work_wq' static
ipmi: Move remove_work to dedicated workqueue
getrusage(RUSAGE_THREAD) with nohz_full may return shorter utime/stime
than the actual time.
task_cputime_adjusted() snapshots utime and stime and then adjust their
sum to match the scheduler maintained cputime.sum_exec_runtime.
Unfortunately in nohz_full, sum_exec_runtime is only updated once per
second in the worst case, causing a discrepancy against utime and stime
that can be updated anytime by the reader using vtime.
To fix this situation, perform an update of cputime.sum_exec_runtime
when the cputime snapshot reports the task as actually running while
the tick is disabled. The related overhead is then contained within the
relevant situations.
Reported-by: Hasegawa Hitomi <hasegawa-hitomi@fujitsu.com>
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Hasegawa Hitomi <hasegawa-hitomi@fujitsu.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Masayoshi Mizuma <m.mizuma@jp.fujitsu.com>
Acked-by: Phil Auld <pauld@redhat.com>
Link: https://lore.kernel.org/r/20211026141055.57358-3-frederic@kernel.org
When at least one CPU runs in nohz_full mode, a dedicated timekeeper CPU
is guaranteed to stay online and to never stop its tick.
Meanwhile on some rare case, the dedicated timekeeper may be running
with interrupts disabled for a while, such as in stop_machine.
If jiffies stop being updated, a nohz_full CPU may end up endlessly
programming the next tick in the past, taking the last jiffies update
monotonic timestamp as a stale base, resulting in an tick storm.
Here is a scenario where it matters:
0) CPU 0 is the timekeeper and CPU 1 a nohz_full CPU.
1) A stop machine callback is queued to execute somewhere.
2) CPU 0 reaches MULTI_STOP_DISABLE_IRQ while CPU 1 is still in
MULTI_STOP_PREPARE. Hence CPU 0 can't do its timekeeping duty. CPU 1
can still take IRQs.
3) CPU 1 receives an IRQ which queues a timer callback one jiffy forward.
4) On IRQ exit, CPU 1 schedules the tick one jiffy forward, taking
last_jiffies_update as a base. But last_jiffies_update hasn't been
updated for 2 jiffies since the timekeeper has interrupts disabled.
5) clockevents_program_event(), which relies on ktime_get(), observes
that the expiration is in the past and therefore programs the min
delta event on the clock.
6) The tick fires immediately, goto 3)
7) Tick storm, the nohz_full CPU is drown and takes ages to reach
MULTI_STOP_DISABLE_IRQ, which is the only way out of this situation.
Solve this with unconditionally updating jiffies if the value is stale
on nohz_full IRQ entry. IRQs and other disturbances are expected to be
rare enough on nohz_full for the unconditional call to ktime_get() to
actually matter.
Reported-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Paul E. McKenney <paulmck@kernel.org>
Link: https://lore.kernel.org/r/20211026141055.57358-2-frederic@kernel.org
Currently autoloading for SPI devices does not use the DT ID table, it
uses SPI modalises. Supporting OF modalises is going to be difficult if
not impractical, an attempt was made but has been reverted, so ensure
that module autoloading works for this driver by adding an id_table
listing the SPI IDs for everything.
Fixes: 96c8395e21 ("spi: Revert modalias changes")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ipv6_addr_bind/ipv4_addr_bind are function names. Previously, bind test
would not be run by default due to the wrong case names
Fixes: 34d0302ab8 ("selftests: Add ipv6 address bind tests to fcnal-test")
Fixes: 75b2b2b3db ("selftests: Add ipv4 address bind tests to fcnal-test")
Signed-off-by: Li Zhijian <lizhijian@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Correct an error where setting /proc/sys/net/rds/tcp/rds_tcp_rcvbuf would
instead modify the socket's sk_sndbuf and would leave sk_rcvbuf untouched.
Fixes: c6a58ffed5 ("RDS: TCP: Add sysctl tunables for sndbuf/rcvbuf on rds-tcp socket")
Signed-off-by: William Kucharski <william.kucharski@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to test against the existing route type, not
the rtm_type in the netlink request.
Fixes: 83f0a0b728 ("mctp: Specify route types, require rtm_type in RTM_*ROUTE messages")
Signed-off-by: Matt Johnston <matt@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
When smc_close_final() returns error, the return code overwrites by
kernel_sock_shutdown() in smc_close_active(). The return code of
smc_close_final() is more important than kernel_sock_shutdown(), and it
will pass to userspace directly.
Fix it by keeping both return codes, if smc_close_final() raises an
error, return it or kernel_sock_shutdown()'s.
Link: https://lore.kernel.org/linux-s390/1f67548e-cbf6-0dce-82b5-10288a4583bd@linux.ibm.com/
Fixes: 606a63c978 ("net/smc: Ensure the active closing peer first closes clcsock")
Suggested-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Tony Lu <tonylu@linux.alibaba.com>
Reviewed-by: Wen Gu <guwen@linux.alibaba.com>
Acked-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When trying to decide whether or not reuse existing rx/tx pools
we tried to allow a range of values for the pool parameters rather
than exact matches. This was intended to reuse the resources for
instance when switching between two VIO servers with different
default parameters.
But this optimization is incomplete and breaks when we try to
change the number of queues for instance. The optimization needs
to be updated, so drop it for now and simplify the code.
Fixes: bbd809305b ("ibmvnic: Reuse tx pools when possible")
Reported-by: Dany Madden <drt@linux.ibm.com>
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Reviewed-by: Dany Madden <drt@linux.ibm.com>
Reviewed-by: Rick Lindsley <ricklind@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When trying to decide whether or not reuse existing rx/tx pools
we tried to allow a range of values for the pool parameters rather
than exact matches. This was intended to reuse the resources for
instance when switching between two VIO servers with different
default parameters.
But this optimization is incomplete and breaks when we try to
change the number of queues for instance. The optimization needs
to be updated, so drop it for now and simplify the code.
Fixes: 489de956e7 ("ibmvnic: Reuse rx pools when possible")
Reported-by: Dany Madden <drt@linux.ibm.com>
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Reviewed-by: Dany Madden <drt@linux.ibm.com>
Reviewed-by: Rick Lindsley <ricklind@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The description of ETH_P_802_3_MIN is misleading.
The value of EthernetType in Ethernet II frame is more than 0x0600,
the value of Length in 802.3 frame is less than 0x0600.
Signed-off-by: Xiayu Zhang <Xiayu.Zhang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Apple M1 Mac minis (2020) with 10GE NICs do not have MAC address in the
card, but instead need to obtain MAC addresses from the device tree. In
this case the hardware will report an invalid MAC.
Currently atlantic driver does not query the DT for MAC address and will
randomly assign a MAC if the NIC doesn't have a permanent MAC burnt in.
This patch causes the driver to perfer a valid MAC address from OF (if
present) over HW self-reported MAC and only fall back to a random MAC
address when neither of them is valid.
Signed-off-by: Tianhao Chai <cth451@gmail.com>
Reviewed-by: Igor Russkikh <irusskikh@marvell.com>
Reviewed-by: Hector Martin <marcan@marcan.st>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before commit faa041a40b ("ipv4: Create cleanup helper for fib_nh")
changes to net->ipv4.fib_num_tclassid_users were protected by RTNL.
After the change, this is no longer the case, as free_fib_info_rcu()
runs after rcu grace period, without rtnl being held.
Fixes: faa041a40b ("ipv4: Create cleanup helper for fib_nh")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: David Ahern <dsahern@kernel.org>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When gfs2_lookup_by_inum() calls gfs2_inode_lookup() for an uncached
inode, gfs2_inode_lookup() will place a new tentative inode into the
inode cache before verifying that there is a valid inode at the given
address. This can race with gfs2_create_inode() which doesn't check for
duplicates inodes. gfs2_create_inode() will try to assign the new inode
to the corresponding inode glock, and glock_set_object() will complain
that the glock is still in use by gfs2_inode_lookup's tentative inode.
We noticed this bug after adding commit 486408d690 ("gfs2: Cancel
remote delete work asynchronously") which allowed delete_work_func() to
race with gfs2_create_inode(), but the same race exists for
open-by-handle.
Fix that by switching from insert_inode_hash() to
insert_inode_locked4(), which does check for duplicate inodes. We know
we've just managed to to allocate the new inode, so an inode tentatively
created by gfs2_inode_lookup() will eventually go away and
insert_inode_locked4() will always succeed.
In addition, don't flush the inode glock work anymore (this can now only
make things worse) and clean up glock_{set,clear}_object for the inode
glock somewhat.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Rework gfs2_inode_lookup() to only set up the new inode's glocks after
verifying that the new inode is valid.
There is no need for flushing the inode glock work queue anymore now,
so remove that as well.
While at it, get rid of the useless wrapper around iget5_locked() and
its unnecessary is_bad_inode() check.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
In gfs2_inode_lookup, once the inode has been looked up, we check if the
inode generation (no_formal_ino) is the one we're looking for. If it
isn't and the inode wasn't in the inode cache, we discard the newly
looked up inode. This is unnecessary, complicates the code, and makes
future changes to gfs2_inode_lookup harder, so change the code to retain
newly looked up inodes instead.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
When we mock up a temporary holder in gfs2_glock_cb to demote weak holders in
response to a remote locking conflict, we don't set the HIF_HOLDER flag. This
causes function may_grant to BUG. Fix by setting the missing HIF_HOLDER flag
in the mock glock holder.
In addition, define the mock glock holder where it is used.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
When branch target identifiers are in use, code reachable via an
indirect branch requires a BTI landing pad at the branch target site.
When building FTRACE_WITH_REGS atop patchable-function-entry, we miss
BTIs at the start start of the `ftrace_caller` and `ftrace_regs_caller`
trampolines, and when these are called from a module via a PLT (which
will use a `BR X16`), we will encounter a BTI failure, e.g.
| # insmod lkdtm.ko
| lkdtm: No crash points registered, enable through debugfs
| # echo function_graph > /sys/kernel/debug/tracing/current_tracer
| # cat /sys/kernel/debug/provoke-crash/DIRECT
| Unhandled 64-bit el1h sync exception on CPU0, ESR 0x34000001 -- BTI
| CPU: 0 PID: 174 Comm: cat Not tainted 5.16.0-rc2-dirty #3
| Hardware name: linux,dummy-virt (DT)
| pstate: 60400405 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=jc)
| pc : ftrace_caller+0x0/0x3c
| lr : lkdtm_debugfs_open+0xc/0x20 [lkdtm]
| sp : ffff800012e43b00
| x29: ffff800012e43b00 x28: 0000000000000000 x27: ffff800012e43c88
| x26: 0000000000000000 x25: 0000000000000000 x24: ffff0000c171f200
| x23: ffff0000c27b1e00 x22: ffff0000c2265240 x21: ffff0000c23c8c30
| x20: ffff8000090ba380 x19: 0000000000000000 x18: 0000000000000000
| x17: 0000000000000000 x16: ffff80001002bb4c x15: 0000000000000000
| x14: 0000000000000000 x13: 0000000000000000 x12: 0000000000900ff0
| x11: ffff0000c4166310 x10: ffff800012e43b00 x9 : ffff8000104f2384
| x8 : 0000000000000001 x7 : 0000000000000000 x6 : 000000000000003f
| x5 : 0000000000000040 x4 : ffff800012e43af0 x3 : 0000000000000001
| x2 : ffff8000090b0000 x1 : ffff0000c171f200 x0 : ffff0000c23c8c30
| Kernel panic - not syncing: Unhandled exception
| CPU: 0 PID: 174 Comm: cat Not tainted 5.16.0-rc2-dirty #3
| Hardware name: linux,dummy-virt (DT)
| Call trace:
| dump_backtrace+0x0/0x1a4
| show_stack+0x24/0x30
| dump_stack_lvl+0x68/0x84
| dump_stack+0x1c/0x38
| panic+0x168/0x360
| arm64_exit_nmi.isra.0+0x0/0x80
| el1h_64_sync_handler+0x68/0xd4
| el1h_64_sync+0x78/0x7c
| ftrace_caller+0x0/0x3c
| do_dentry_open+0x134/0x3b0
| vfs_open+0x38/0x44
| path_openat+0x89c/0xe40
| do_filp_open+0x8c/0x13c
| do_sys_openat2+0xbc/0x174
| __arm64_sys_openat+0x6c/0xbc
| invoke_syscall+0x50/0x120
| el0_svc_common.constprop.0+0xdc/0x100
| do_el0_svc+0x84/0xa0
| el0_svc+0x28/0x80
| el0t_64_sync_handler+0xa8/0x130
| el0t_64_sync+0x1a0/0x1a4
| SMP: stopping secondary CPUs
| Kernel Offset: disabled
| CPU features: 0x0,00000f42,da660c5f
| Memory Limit: none
| ---[ end Kernel panic - not syncing: Unhandled exception ]---
Fix this by adding the required `BTI C`, as we only require these to be
reachable via BL for direct calls or BR X16/X17 for PLTs. For now, these
are open-coded in the function prologue, matching the style of the
`__hwasan_tag_mismatch` trampoline.
In future we may wish to consider adding a new SYM_CODE_START_*()
variant which has an implicit BTI.
When ftrace is built atop mcount, the trampolines are marked with
SYM_FUNC_START(), and so get an implicit BTI. We may need to change
these over to SYM_CODE_START() in future for RELIABLE_STACKTRACE, in
case we need to apply special care aroud the return address being
rewritten.
Fixes: 97fed779f2 ("arm64: bti: Provide Kconfig for kernel mode BTI")
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Will Deacon <will@kernel.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20211129135709.2274019-1-mark.rutland@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
In machine_kexec_post_load() we use __pa() on `empty_zero_page`, so that
we can use the physical address during arm64_relocate_new_kernel() to
switch TTBR1 to a new set of tables. While `empty_zero_page` is part of
the old kernel, we won't clobber it until after this switch, so using it
is benign.
However, `empty_zero_page` is part of the kernel image rather than a
linear map address, so it is not correct to use __pa(x), and we should
instead use __pa_symbol(x) or __pa(lm_alias(x)). Otherwise, when the
kernel is built with DEBUG_VIRTUAL, we'll encounter splats as below, as
I've seen when fuzzing v5.16-rc3 with Syzkaller:
| ------------[ cut here ]------------
| virt_to_phys used for non-linear address: 000000008492561a (empty_zero_page+0x0/0x1000)
| WARNING: CPU: 3 PID: 11492 at arch/arm64/mm/physaddr.c:15 __virt_to_phys+0x120/0x1c0 arch/arm64/mm/physaddr.c:12
| CPU: 3 PID: 11492 Comm: syz-executor.0 Not tainted 5.16.0-rc3-00001-g48bd452a045c #1
| Hardware name: linux,dummy-virt (DT)
| pstate: 60400005 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
| pc : __virt_to_phys+0x120/0x1c0 arch/arm64/mm/physaddr.c:12
| lr : __virt_to_phys+0x120/0x1c0 arch/arm64/mm/physaddr.c:12
| sp : ffff80001af17bb0
| x29: ffff80001af17bb0 x28: ffff1cc65207b400 x27: ffffb7828730b120
| x26: 0000000000000e11 x25: 0000000000000000 x24: 0000000000000001
| x23: ffffb7828963e000 x22: ffffb78289644000 x21: 0000600000000000
| x20: 000000000000002d x19: 0000b78289644000 x18: 0000000000000000
| x17: 74706d6528206131 x16: 3635323934383030 x15: 303030303030203a
| x14: 1ffff000035e2eb8 x13: ffff6398d53f4f0f x12: 1fffe398d53f4f0e
| x11: 1fffe398d53f4f0e x10: ffff6398d53f4f0e x9 : ffffb7827c6f76dc
| x8 : ffff1cc6a9fa7877 x7 : 0000000000000001 x6 : ffff6398d53f4f0f
| x5 : 0000000000000000 x4 : 0000000000000000 x3 : ffff1cc66f2a99c0
| x2 : 0000000000040000 x1 : d7ce7775b09b5d00 x0 : 0000000000000000
| Call trace:
| __virt_to_phys+0x120/0x1c0 arch/arm64/mm/physaddr.c:12
| machine_kexec_post_load+0x284/0x670 arch/arm64/kernel/machine_kexec.c:150
| do_kexec_load+0x570/0x670 kernel/kexec.c:155
| __do_sys_kexec_load kernel/kexec.c:250 [inline]
| __se_sys_kexec_load kernel/kexec.c:231 [inline]
| __arm64_sys_kexec_load+0x1d8/0x268 kernel/kexec.c:231
| __invoke_syscall arch/arm64/kernel/syscall.c:38 [inline]
| invoke_syscall+0x90/0x2e0 arch/arm64/kernel/syscall.c:52
| el0_svc_common.constprop.2+0x1e4/0x2f8 arch/arm64/kernel/syscall.c:142
| do_el0_svc+0xf8/0x150 arch/arm64/kernel/syscall.c:181
| el0_svc+0x60/0x248 arch/arm64/kernel/entry-common.c:603
| el0t_64_sync_handler+0x90/0xb8 arch/arm64/kernel/entry-common.c:621
| el0t_64_sync+0x180/0x184 arch/arm64/kernel/entry.S:572
| irq event stamp: 2428
| hardirqs last enabled at (2427): [<ffffb7827c6f2308>] __up_console_sem+0xf0/0x118 kernel/printk/printk.c:255
| hardirqs last disabled at (2428): [<ffffb7828223df98>] el1_dbg+0x28/0x80 arch/arm64/kernel/entry-common.c:375
| softirqs last enabled at (2424): [<ffffb7827c411c00>] softirq_handle_end kernel/softirq.c:401 [inline]
| softirqs last enabled at (2424): [<ffffb7827c411c00>] __do_softirq+0xa28/0x11e4 kernel/softirq.c:587
| softirqs last disabled at (2417): [<ffffb7827c59015c>] do_softirq_own_stack include/asm-generic/softirq_stack.h:10 [inline]
| softirqs last disabled at (2417): [<ffffb7827c59015c>] invoke_softirq kernel/softirq.c:439 [inline]
| softirqs last disabled at (2417): [<ffffb7827c59015c>] __irq_exit_rcu kernel/softirq.c:636 [inline]
| softirqs last disabled at (2417): [<ffffb7827c59015c>] irq_exit_rcu+0x53c/0x688 kernel/softirq.c:648
| ---[ end trace 0ca578534e7ca938 ]---
With or without DEBUG_VIRTUAL __pa() will fall back to __kimg_to_phys()
for non-linear addresses, and will happen to do the right thing in this
case, even with the warning. But we should not depend upon this, and to
keep the warning useful we should fix this case.
Fix this issue by using __pa_symbol(), which handles kernel image
addresses (and checks its input is a kernel image address). This matches
what we do elsewhere, e.g. in arch/arm64/include/asm/pgtable.h:
| #define ZERO_PAGE(vaddr) phys_to_page(__pa_symbol(empty_zero_page))
Fixes: 3744b5280e ("arm64: kexec: install a copy of the linear-map")
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Pasha Tatashin <pasha.tatashin@soleen.com>
Cc: Will Deacon <will@kernel.org>
Reviewed-by: Pasha Tatashin <pasha.tatashin@soleen.com>
Link: https://lore.kernel.org/r/20211130121849.3319010-1-mark.rutland@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
Remove the paragraph which has nothing to do with the kernel and
add PAC description related to kernel.
Suggested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Kuan-Ying Lee <Kuan-Ying.Lee@mediatek.com>
Link: https://lore.kernel.org/r/20211201034014.20048-1-Kuan-Ying.Lee@mediatek.com
Signed-off-by: Will Deacon <will@kernel.org>
Bail from the page fault handler if the root shadow page was obsoleted by
a memslot update. Do the check _after_ acuiring mmu_lock, as the TDP MMU
doesn't rely on the memslot/MMU generation, and instead relies on the
root being explicit marked invalid by kvm_mmu_zap_all_fast(), which takes
mmu_lock for write.
For the TDP MMU, inserting a SPTE into an obsolete root can leak a SP if
kvm_tdp_mmu_zap_invalidated_roots() has already zapped the SP, i.e. has
moved past the gfn associated with the SP.
For other MMUs, the resulting behavior is far more convoluted, though
unlikely to be truly problematic. Installing SPs/SPTEs into the obsolete
root isn't directly problematic, as the obsolete root will be unloaded
and dropped before the vCPU re-enters the guest. But because the legacy
MMU tracks shadow pages by their role, any SP created by the fault can
can be reused in the new post-reload root. Again, that _shouldn't_ be
problematic as any leaf child SPTEs will be created for the current/valid
memslot generation, and kvm_mmu_get_page() will not reuse child SPs from
the old generation as they will be flagged as obsolete. But, given that
continuing with the fault is pointess (the root will be unloaded), apply
the check to all MMUs.
Fixes: b7cccd397f ("KVM: x86/mmu: Fast invalidation for TDP MMU")
Cc: stable@vger.kernel.org
Cc: Ben Gardon <bgardon@google.com>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20211120045046.3940942-5-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The error paths in the prepare_vmcs02() function are supposed to set
*entry_failure_code but this path does not. It leads to using an
uninitialized variable in the caller.
Fixes: 71f7347025 ("KVM: nVMX: Load GUEST_IA32_PERF_GLOBAL_CTRL MSR on VM-Entry")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Message-Id: <20211130125337.GB24578@kili>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
kvm_vcpu_apicv_active() returns false if a virtual machine has no in-kernel
local APIC, however kvm_apicv_activated might still be true if there are
no reasons to disable APICv; in fact it is quite likely that there is none
because APICv is inhibited by specific configurations of the local APIC
and those configurations cannot be programmed. This triggers a WARN:
WARN_ON_ONCE(kvm_apicv_activated(vcpu->kvm) != kvm_vcpu_apicv_active(vcpu));
To avoid this, introduce another cause for APICv inhibition, namely the
absence of an in-kernel local APIC. This cause is enabled by default,
and is dropped by either KVM_CREATE_IRQCHIP or the enabling of
KVM_CAP_IRQCHIP_SPLIT.
Reported-by: Ignat Korchagin <ignat@cloudflare.com>
Fixes: ee49a89329 ("KVM: x86: Move SVM's APICv sanity check to common x86", 2021-10-22)
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Sean Christopherson <seanjc@google.com>
Tested-by: Ignat Korchagin <ignat@cloudflare.com>
Message-Id: <20211130123746.293379-1-pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If we run the following perf command in an AMD Milan guest:
perf stat \
-e cpu/event=0x1d0/ \
-e cpu/event=0x1c7/ \
-e cpu/umask=0x1f,event=0x18e/ \
-e cpu/umask=0x7,event=0x18e/ \
-e cpu/umask=0x18,event=0x18e/ \
./workload
dmesg will report a #GP warning from an unchecked MSR access
error on MSR_F15H_PERF_CTLx.
This is because according to APM (Revision: 4.03) Figure 13-7,
the bits [35:32] of AMD PerfEvtSeln register is a part of the
event select encoding, which extends the EVENT_SELECT field
from 8 bits to 12 bits.
Opportunistically update pmu->reserved_bits for reserved bit 19.
Reported-by: Jim Mattson <jmattson@google.com>
Fixes: ca724305a2 ("KVM: x86/vPMU: Implement AMD vPMU code for KVM")
Signed-off-by: Like Xu <likexu@tencent.com>
Message-Id: <20211118130320.95997-1-likexu@tencent.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
coccinelle report：
./drivers/ata/libata-sata.c:830:8-16:
WARNING: use scnprintf or sprintf
Use sysfs_emit instead of scnprintf or sprintf makes more sense.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Yang Guang <yang.guang5@zte.com.cn>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
In rvu_mbox_init(), mbox_regions is not freed or passed out
under the switch-default region, which could lead to a memory leak.
Fix this bug by changing 'return err' to 'goto free_regions'.
This bug was found by a static analyzer. The analysis employs
differential checking to identify inconsistent security operations
(e.g., checks or kfrees) between two code paths and confirms that the
inconsistent operations are not recovered in the current function or
the callers, so they constitute bugs.
Note that, as a bug found by static analysis, it can be a false
positive or hard to trigger. Multiple researchers have cross-reviewed
the bug.
Builds with CONFIG_OCTEONTX2_AF=y show no new warnings,
and our static analyzer no longer warns about this code.
Fixes: 98c5611163 (“octeontx2-af: cn10k: Add mbox support for CN10K platform”)
Signed-off-by: Zhou Qingyang <zhou1615@umn.edu>
Link: https://lore.kernel.org/r/20211130165039.192426-1-zhou1615@umn.edu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In mlx4_en_try_alloc_resources(), mlx4_en_copy_priv() is called and
tmp->tx_cq will be freed on the error path of mlx4_en_copy_priv().
After that mlx4_en_alloc_resources() is called and there is a dereference
of &tmp->tx_cq[t][i] in mlx4_en_alloc_resources(), which could lead to
a use after free problem on failure of mlx4_en_copy_priv().
Fix this bug by adding a check of mlx4_en_copy_priv()
This bug was found by a static analyzer. The analysis employs
differential checking to identify inconsistent security operations
(e.g., checks or kfrees) between two code paths and confirms that the
inconsistent operations are not recovered in the current function or
the callers, so they constitute bugs.
Note that, as a bug found by static analysis, it can be a false
positive or hard to trigger. Multiple researchers have cross-reviewed
the bug.
Builds with CONFIG_MLX4_EN=m show no new warnings,
and our static analyzer no longer warns about this code.
Fixes: ec25bc04ed ("net/mlx4_en: Add resilience in low memory systems")
Signed-off-by: Zhou Qingyang <zhou1615@umn.edu>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20211130164438.190591-1-zhou1615@umn.edu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
IPCB/IP6CB need to be initialized when processing outbound v4 or v6 pkts
in the codepath of vrf device xmit function so that leftover garbage
doesn't cause futher code that uses the CB to incorrectly process the
pkt.
One occasion of the issue might occur when MPLS route uses the vrf
device as the outgoing device such as when the route is added using "ip
-f mpls route add <label> dev <vrf>" command.
The problems seems to exist since day one. Hence I put the day one
commits on the Fixes tags.
Fixes: 193125dbd8 ("net: Introduce VRF device driver")
Fixes: 35402e3136 ("net: Add IPv6 support to VRF device")
Cc: stable@vger.kernel.org
Signed-off-by: Stephen Suryaputra <ssuryaextr@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20211130162637.3249-1-ssuryaextr@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In qlcnic_83xx_add_rings(), the indirect function of
ahw->hw_ops->alloc_mbx_args will be called to allocate memory for
cmd.req.arg, and there is a dereference of it in qlcnic_83xx_add_rings(),
which could lead to a NULL pointer dereference on failure of the
indirect function like qlcnic_83xx_alloc_mbx_args().
Fix this bug by adding a check of alloc_mbx_args(), this patch
imitates the logic of mbx_cmd()'s failure handling.
This bug was found by a static analyzer. The analysis employs
differential checking to identify inconsistent security operations
(e.g., checks or kfrees) between two code paths and confirms that the
inconsistent operations are not recovered in the current function or
the callers, so they constitute bugs.
Note that, as a bug found by static analysis, it can be a false
positive or hard to trigger. Multiple researchers have cross-reviewed
the bug.
Builds with CONFIG_QLCNIC=m show no new warnings, and our
static analyzer no longer warns about this code.
Fixes: 7f9664525f ("qlcnic: 83xx memory map and HW access routine")
Signed-off-by: Zhou Qingyang <zhou1615@umn.edu>
Link: https://lore.kernel.org/r/20211130110848.109026-1-zhou1615@umn.edu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The 'kprobe::data_size' is unsigned, thus it can not be negative. But if
user sets it enough big number (e.g. (size_t)-8), the result of 'data_size
+ sizeof(struct kretprobe_instance)' becomes smaller than sizeof(struct
kretprobe_instance) or zero. In result, the kretprobe_instance are
allocated without enough memory, and kretprobe accesses outside of
allocated memory.
To avoid this issue, introduce a max limitation of the
kretprobe::data_size. 4KB per instance should be OK.
Link: https://lkml.kernel.org/r/163836995040.432120.10322772773821182925.stgit@devnote2
Cc: stable@vger.kernel.org
Fixes: f47cd9b553 ("kprobes: kretprobe user entry-handler")
Reported-by: zhangyue <zhangyue1@kylinos.cn>
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
When comparing two strings for the "onmatch" histogram trigger, fields
that are strings use string comparisons, which do not care about being
signed or not.
Do not fail to match two string fields if one is unsigned char array and
the other is a signed char array.
Link: https://lore.kernel.org/all/20211129123043.5cfd687a@gandalf.local.home/
Cc: stable@vgerk.kernel.org
Cc: Tom Zanussi <zanussi@kernel.org>
Cc: Yafang Shao <laoar.shao@gmail.com>
Fixes: b05e89ae7c ("tracing: Accept different type for synthetic event fields")
Reviewed-by: Masami Hiramatsu <mhiramatsu@kernel.org>
Reported-by: Sven Schnelle <svens@linux.ibm.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
This ASSERT in xfs_rename is a) incorrect, because
(RENAME_WHITEOUT|RENAME_NOREPLACE) is a valid combination, and
b) unnecessary, because actual invalid flag combinations are already
handled at the vfs level in do_renameat2() before we get called.
So, remove it.
Reported-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Darrick J. Wong <djwong@kernel.org>
There are cases that the TSC clocksource is wrongly judged as unstable by
the clocksource watchdog mechanism which tries to validate the TSC against
HPET, PM_TIMER or jiffies. While there is hardly a general reliable way to
check the validity of a watchdog, Thomas Gleixner proposed [1]:
"I'm inclined to lift that requirement when the CPU has:
1) X86_FEATURE_CONSTANT_TSC
2) X86_FEATURE_NONSTOP_TSC
3) X86_FEATURE_NONSTOP_TSC_S3
4) X86_FEATURE_TSC_ADJUST
5) At max. 4 sockets
After two decades of horrors we're finally at a point where TSC seems
to be halfway reliable and less abused by BIOS tinkerers. TSC_ADJUST
was really key as we can now detect even small modifications reliably
and the important point is that we can cure them as well (not pretty
but better than all other options)."
As feature #3 X86_FEATURE_NONSTOP_TSC_S3 only exists on several generations
of Atom processorz, and is always coupled with X86_FEATURE_CONSTANT_TSC
and X86_FEATURE_NONSTOP_TSC, skip checking it, and also be more defensive
to use maximal 2 sockets.
The check is done inside tsc_init() before registering 'tsc-early' and
'tsc' clocksources, as there were cases that both of them had been
wrongly judged as unreliable.
For more background of tsc/watchdog, there is a good summary in [2]
[tglx} Update vs. jiffies:
On systems where the only remaining clocksource aside of TSC is jiffies
there is no way to make this work because that creates a circular
dependency. Jiffies accuracy depends on not missing a periodic timer
interrupt, which is not guaranteed. That could be detected by TSC, but as
TSC is not trusted this cannot be compensated. The consequence is a
circulus vitiosus which results in shutting down TSC and falling back to
the jiffies clocksource which is even more unreliable.
[1]. https://lore.kernel.org/lkml/87eekfk8bd.fsf@nanos.tec.linutronix.de/
[2]. https://lore.kernel.org/lkml/87a6pimt1f.ffs@nanos.tec.linutronix.de/
[ tglx: Refine comment and amend changelog ]
Fixes: 6e3cd95234 ("x86/hpet: Use another crystalball to evaluate HPET usability")
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: "Paul E. McKenney" <paulmck@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20211117023751.24190-2-feng.tang@intel.com
