Add read/write latencies and bandwidth sysfs attributes for the enabled CXL
region. The bandwidth is the aggregated bandwidth of all devices that
contribute to the CXL region. The latency is the worst latency of the
device amongst all the devices that contribute to the CXL region.
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Tested-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/20240308220055.2172956-11-dave.jiang@intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Calculate and store the performance data for a CXL region. Find the worst
read and write latency for all the included ranges from each of the devices
that attributes to the region and designate that as the latency data. Sum
all the read and write bandwidth data for each of the device region and
that is the total bandwidth for the region.
The perf list is expected to be constructed before the endpoint decoders
are registered and thus there should be no early reading of the entries
from the region assemble action. The calling of the region qos calculate
function is under the protection of cxl_dpa_rwsem and will ensure that
all DPA associated work has completed.
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Tested-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/20240308220055.2172956-10-dave.jiang@intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Move setting of cxlmd->endpoint to before calling add_device() on the port
device. Otherwise when referencing cxlmd->endpoint in region discovery code
that is triggered by the port driver probe function, the endpoint port
pointer is not valid.
Current code does not hit this issue yet since cxlmd->endpoint is not being
referenced during region discovery. However follow on code that does
performance calculations will.
Tested-by: Wonjae Lee <wj28.lee@samsung.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Tested-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/20240308220055.2172956-9-dave.jiang@intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Retrieve the qos_class (QTG ID) using the access coordinates from the
nearest CPU rather than the nearst initiator that may not be a CPU.
This may be the more appropriate number that applications care about.
For most cases, access0 and access1 have the same values.
Link: https://lore.kernel.org/linux-cxl/20240112113023.00006c50@Huawei.com/
Suggested-by: Jonathan Cameron <jonathan.cameron@huawei.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Tested-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/20240308220055.2172956-8-dave.jiang@intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The difference between access class 0 and access class 1 for 'struct
access_coordinate', if any, is that class 0 is for the distance from
the target to the closest initiator and that class 1 is for the distance
from the target to the closest CPU. For CXL memory, the nearest initiator
may not necessarily be a CPU node. The performance path from the CXL
endpoint to the host bridge should remain the same. However, the numbers
extracted and stored from HMAT is the difference for the two access
classes. Split out the performance numbers for the host bridge (generic
target) from the calculation of the entire path in order to allow
calculation of both access classes for a CXL region.
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Tested-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/20240308220055.2172956-7-dave.jiang@intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Refactor the common code of combining coordinates in order to reduce code.
Create a new function cxl_cooordinates_combine() it combine two 'struct
access_coordinate'.
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Tested-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/20240308220055.2172956-6-dave.jiang@intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Update acpi_get_genport_coordinates() to allow retrieval of both access
classes of the 'struct access_coordinate' for a generic target. The update
will allow CXL code to compute access coordinates for both access class.
Cc: Rafael J. Wysocki <rafael@kernel.org>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Tested-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/20240308220055.2172956-5-dave.jiang@intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
In order to compute access0 and access1 classes for CXL memory, 2 levels
of generic port information must be stored. Access0 will indicate the
generic port access coordinates to the closest initiator and access1
will indicate the generic port access coordinates to the cloest CPU.
Cc: Rafael J. Wysocki <rafael@kernel.org>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Tested-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/20240308220055.2172956-4-dave.jiang@intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Both generic node and HMAT handling code have been using magic numbers to
indicate access classes for 'struct access_coordinate'. Introduce enums to
enumerate the access0 and access1 classes shared by the two subsystems.
Update the function parameters and callers as appropriate to utilize the
new enum.
Access0 is named to ACCESS_COORDINATE_LOCAL in order to indicate that the
access class is for 'struct access_coordinate' between a target node and
the nearest initiator node.
Access1 is named to ACCESS_COORDINATE_CPU in order to indicate that the
access class is for 'struct access_coordinate' between a target node and
the nearest CPU node.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Rafael J. Wysocki <rafael@kernel.org>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Tested-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/20240308220055.2172956-3-dave.jiang@intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
For generic targets, there's no reason to call
register_memory_node_under_compute_node() with the access levels that are
only visible to HMAT handling code. Only update the attributes and rename
hmat_register_generic_target_initiators() to hmat_update_generic_target().
The original call path ends up triggering register_memory_node_under_compute_node().
Although the access level would be "3" and not impact any current node arrays, it
introduces unwanted data into the numa node access_coordinate array.
Fixes: a3a3e341f1 ("acpi: numa: Add setting of generic port system locality attributes")
Cc: Rafael J. Wysocki <rafael@kernel.org>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Tested-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/20240308220055.2172956-2-dave.jiang@intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Some more mostly boring fixes, but some not
User reported ones:
- the BTREE_ITER_FILTER_SNAPSHOTS one fixes a really nasty performance
bug; user reported an unter initially taking 2 seconds and then ~2
minutes
- kill a __GFP_NOFAIL in the buffered read path; this was a leftover
from the trickier fix to kill __GFP_NOFAIL in readahead, where we
can't return errors (and have to silently truncate the read
ourselves).
bcachefs can't use GFP_NOFAIL for folio state unlike iomap based
filesystems because our folio state is just barely too big, 2MB
hugepages cause us to exceed the 2 page threshhold for GFP_NOFAIL.
additionally, the flags argument was just buggy, we weren't supplying
GFP_KERNEL previously (!).
-----BEGIN PGP SIGNATURE-----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=KNWR
-----END PGP SIGNATURE-----
Merge tag 'bcachefs-2024-02-25' of https://evilpiepirate.org/git/bcachefs
Pull bcachefs fixes from Kent Overstreet:
"Some more mostly boring fixes, but some not
User reported ones:
- the BTREE_ITER_FILTER_SNAPSHOTS one fixes a really nasty
performance bug; user reported an untar initially taking two
seconds and then ~2 minutes
- kill a __GFP_NOFAIL in the buffered read path; this was a leftover
from the trickier fix to kill __GFP_NOFAIL in readahead, where we
can't return errors (and have to silently truncate the read
ourselves).
bcachefs can't use GFP_NOFAIL for folio state unlike iomap based
filesystems because our folio state is just barely too big, 2MB
hugepages cause us to exceed the 2 page threshhold for GFP_NOFAIL.
additionally, the flags argument was just buggy, we weren't
supplying GFP_KERNEL previously (!)"
* tag 'bcachefs-2024-02-25' of https://evilpiepirate.org/git/bcachefs:
bcachefs: fix bch2_save_backtrace()
bcachefs: Fix check_snapshot() memcpy
bcachefs: Fix bch2_journal_flush_device_pins()
bcachefs: fix iov_iter count underflow on sub-block dio read
bcachefs: Fix BTREE_ITER_FILTER_SNAPSHOTS on inodes btree
bcachefs: Kill __GFP_NOFAIL in buffered read path
bcachefs: fix backpointer_to_text() when dev does not exist
- The XFS online fsck documentation uses incredibly deeply nested
subsection and list nesting; that broke the PDF docs build. Tweak a
parameter to tell LaTeX to allow the deeper nesting.
- Fix a 6.8 PDF-build regression
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEIw+MvkEiF49krdp9F0NaE2wMflgFAmXbi5QPHGNvcmJldEBs
d24ubmV0AAoJEBdDWhNsDH5YZSMH/RIZh48S/Jh5mhjzqnKhGf1sFn6lSk8sFY3I
uJqML/LPo6GYzX8WvYKlfyP9+UvrLiDcQF0Er6MeIhK6mhKE1Lp7w1YvRgeXcgFR
H9DtxA4fJSGWlAaMqZBwsXjF2EFwjyxHtHUeNyaJ+YocHfrT6L9Cp9uBEvdT3Iye
F191VpjWLrFD0DJEh64CcmNd3rggN5jeD/n24dbNOmnem1cak2brIIUeltdkUmQG
48Hr27xqYF1QyVckfoRtnT/C3AyaCKbxRbTxeAjwUDjU+7nCsHf1MKltiFAZHnFs
7ZLsOboLhmR+y9xiZUg7OlpRaVj1C+7JSYC+WSaNjwRkkIfJUu4=
=MEzm
-----END PGP SIGNATURE-----
Merge tag 'docs-6.8-fixes3' of git://git.lwn.net/linux
Pull two documentation build fixes from Jonathan Corbet:
- The XFS online fsck documentation uses incredibly deeply nested
subsection and list nesting; that broke the PDF docs build. Tweak a
parameter to tell LaTeX to allow the deeper nesting.
- Fix a 6.8 PDF-build regression
* tag 'docs-6.8-fixes3' of git://git.lwn.net/linux:
docs: translations: use attribute to store current language
docs: Instruct LaTeX to cope with deeper nesting
Here are some small USB fixes for 6.8-rc6 to resolve some reported
problems. These include:
- regression fixes with typec tpcm code as reported by many
- cdnsp and cdns3 driver fixes
- usb role setting code bugfixes
- build fix for uhci driver
- ncm gadget driver bugfix
- MAINTAINERS entry update
All of these have been in linux-next all week with no reported issues
and there is at least one fix in here that is in Thorsten's regression
list that is being tracked.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZdtGEA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymzsgCg2IsWqIR72XUGsa5rrbRnskOP/G4An24BmUb6
t34d0VjiHagZTFlfRx6g
=eOL1
-----END PGP SIGNATURE-----
Merge tag 'usb-6.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some small USB fixes for 6.8-rc6 to resolve some reported
problems. These include:
- regression fixes with typec tpcm code as reported by many
- cdnsp and cdns3 driver fixes
- usb role setting code bugfixes
- build fix for uhci driver
- ncm gadget driver bugfix
- MAINTAINERS entry update
All of these have been in linux-next all week with no reported issues
and there is at least one fix in here that is in Thorsten's regression
list that is being tracked"
* tag 'usb-6.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: typec: tpcm: Fix issues with power being removed during reset
MAINTAINERS: Drop myself as maintainer of TYPEC port controller drivers
usb: gadget: ncm: Avoid dropping datagrams of properly parsed NTBs
Revert "usb: typec: tcpm: reset counter when enter into unattached state after try role"
usb: gadget: omap_udc: fix USB gadget regression on Palm TE
usb: dwc3: gadget: Don't disconnect if not started
usb: cdns3: fix memory double free when handle zero packet
usb: cdns3: fixed memory use after free at cdns3_gadget_ep_disable()
usb: roles: don't get/set_role() when usb_role_switch is unregistered
usb: roles: fix NULL pointer issue when put module's reference
usb: cdnsp: fixed issue with incorrect detecting CDNSP family controllers
usb: cdnsp: blocked some cdns3 specific code
usb: uhci-grlib: Explicitly include linux/platform_device.h
Here are 3 small serial/tty driver fixes for 6.8-rc6 that resolve the
following reported errors:
- riscv hvc console driver fix that was reported by many
- amba-pl011 serial driver fix for RS485 mode
- stm32 serial driver fix for RS485 mode
All of these have been in linux-next all week with no reported problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZdtGnA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymrqwCfSIsUj9GLazXJTTTgMz1I94HXLrQAnjq9QOtg
EFt6xmUGcF4zFhnfSLal
=/k5+
-----END PGP SIGNATURE-----
Merge tag 'tty-6.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver fixes from Greg KH:
"Here are three small serial/tty driver fixes for 6.8-rc6 that resolve
the following reported errors:
- riscv hvc console driver fix that was reported by many
- amba-pl011 serial driver fix for RS485 mode
- stm32 serial driver fix for RS485 mode
All of these have been in linux-next all week with no reported
problems"
* tag 'tty-6.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: amba-pl011: Fix DMA transmission in RS485 mode
serial: stm32: do not always set SER_RS485_RX_DURING_TX if RS485 is enabled
tty: hvc: Don't enable the RISC-V SBI console by default
point in the return-to-userspace path, otherwise memory accesses after
the VERW execution could cause data to land in CPU buffers again
-----BEGIN PGP SIGNATURE-----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=n5us
-----END PGP SIGNATURE-----
Merge tag 'x86_urgent_for_v6.8_rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Borislav Petkov:
- Make sure clearing CPU buffers using VERW happens at the latest
possible point in the return-to-userspace path, otherwise memory
accesses after the VERW execution could cause data to land in CPU
buffers again
* tag 'x86_urgent_for_v6.8_rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
KVM/VMX: Move VERW closer to VMentry for MDS mitigation
KVM/VMX: Use BT+JNC, i.e. EFLAGS.CF to select VMRESUME vs. VMLAUNCH
x86/bugs: Use ALTERNATIVE() instead of mds_user_clear static key
x86/entry_32: Add VERW just before userspace transition
x86/entry_64: Add VERW just before userspace transition
x86/bugs: Add asm helpers for executing VERW
from silently failing to set it up
- Do not call bus_get_dev_root() for the mbigen irqchip as it always
returns NULL - use NULL directly
- Fix hardware interrupt number truncation when assigning MSI interrupts
- Correct sending end-of-interrupt messages to disabled interrupts lines on
RISC-V PLIC
-----BEGIN PGP SIGNATURE-----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=cMur
-----END PGP SIGNATURE-----
Merge tag 'irq_urgent_for_v6.8_rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Borislav Petkov:
- Make sure GICv4 always gets initialized to prevent a kexec-ed kernel
from silently failing to set it up
- Do not call bus_get_dev_root() for the mbigen irqchip as it always
returns NULL - use NULL directly
- Fix hardware interrupt number truncation when assigning MSI
interrupts
- Correct sending end-of-interrupt messages to disabled interrupts
lines on RISC-V PLIC
* tag 'irq_urgent_for_v6.8_rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/gic-v3-its: Do not assume vPE tables are preallocated
irqchip/mbigen: Don't use bus_get_dev_root() to find the parent
PCI/MSI: Prevent MSI hardware interrupt number truncation
irqchip/sifive-plic: Enable interrupt if needed before EOI
- Fix page refcount leak when looking up specific inodes
introduced by metabuf reworking.
-----BEGIN PGP SIGNATURE-----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=/Bfj
-----END PGP SIGNATURE-----
Merge tag 'erofs-for-6.8-rc6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/xiang/erofs
Pull erofs fix from Gao Xiang:
- Fix page refcount leak when looking up specific inodes
introduced by metabuf reworking
* tag 'erofs-for-6.8-rc6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/xiang/erofs:
erofs: fix refcount on the metabuf used for inode lookup
pathwalk. This series is a result of code audit (the second round
of it) and it should deal with most of that stuff. Exceptions: ntfs3
->d_hash()/->d_compare() and ceph_d_revalidate(). Up to maintainers (a
note for NTFS folks - when documentation says that a method may not block,
it *does* imply that blocking allocations are to be avoided. Really).
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQqUNBr3gm4hGXdBJlZ7Krx/gZQ6wUCZdroDAAKCRBZ7Krx/gZQ
60dKAQCzp6rYr3ye4nylho9Rzu8LEpH04TuNf3C6JuyUaNHxHwEAvNLatZsyFnmV
Ksp2Rg/IlKPNtQgYJ8xPxv9DFmNe8gI=
=47Un
-----END PGP SIGNATURE-----
Merge tag 'pull-fixes.pathwalk-rcu-2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull RCU pathwalk fixes from Al Viro:
"We still have some races in filesystem methods when exposed to RCU
pathwalk. This series is a result of code audit (the second round of
it) and it should deal with most of that stuff.
Still pending: ntfs3 ->d_hash()/->d_compare() and ceph_d_revalidate().
Up to maintainers (a note for NTFS folks - when documentation says
that a method may not block, it *does* imply that blocking allocations
are to be avoided. Really)"
[ More explanations for people who aren't familiar with the vagaries of
RCU path walking: most of it is hidden from filesystems, but if a
filesystem actively participates in the low-level path walking it
needs to make sure the fields involved in that walk are RCU-safe.
That "actively participate in low-level path walking" includes things
like having its own ->d_hash()/->d_compare() routines, or by having
its own directory permission function that doesn't just use the common
helpers. Having a ->d_revalidate() function will also have this issue.
Note that instead of making everything RCU safe you can also choose to
abort the RCU pathwalk if your operation cannot be done safely under
RCU, but that obviously comes with a performance penalty. One common
pattern is to allow the simple cases under RCU, and abort only if you
need to do something more complicated.
So not everything needs to be RCU-safe, and things like the inode etc
that the VFS itself maintains obviously already are. But these fixes
tend to be about properly RCU-delaying things like ->s_fs_info that
are maintained by the filesystem and that got potentially released too
early. - Linus ]
* tag 'pull-fixes.pathwalk-rcu-2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
ext4_get_link(): fix breakage in RCU mode
cifs_get_link(): bail out in unsafe case
fuse: fix UAF in rcu pathwalks
procfs: make freeing proc_fs_info rcu-delayed
procfs: move dropping pde and pid from ->evict_inode() to ->free_inode()
nfs: fix UAF on pathwalk running into umount
nfs: make nfs_set_verifier() safe for use in RCU pathwalk
afs: fix __afs_break_callback() / afs_drop_open_mmap() race
hfsplus: switch to rcu-delayed unloading of nls and freeing ->s_fs_info
exfat: move freeing sbi, upcase table and dropping nls into rcu-delayed helper
affs: free affs_sb_info with kfree_rcu()
rcu pathwalk: prevent bogus hard errors from may_lookup()
fs/super.c: don't drop ->s_user_ns until we free struct super_block itself
and a fix for erofs failure exit breakage (had been there since
way back).
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQqUNBr3gm4hGXdBJlZ7Krx/gZQ6wUCZdrkZAAKCRBZ7Krx/gZQ
67D8AP0eM68yZvbThA/Hb5iElDh3Aogt1AW/QAu9/alkDVHr+wD+PKqhamC8WXGk
b1QZ5AOHQFwzkzdF4738fdbujquBWQE=
=Ra0D
-----END PGP SIGNATURE-----
Merge tag 'pull-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs fixes from Al Viro:
"A couple of fixes - revert of regression from this cycle and a fix for
erofs failure exit breakage (had been there since way back)"
* tag 'pull-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
erofs: fix handling kern_mount() failure
Revert "get rid of DCACHE_GENOCIDE"
1) errors from ext4_getblk() should not be propagated to caller
unless we are really sure that we would've gotten the same error
in non-RCU pathwalk.
2) we leak buffer_heads if ext4_getblk() is successful, but bh is
not uptodate.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
->d_revalidate() bails out there, anyway. It's not enough
to prevent getting into ->get_link() in RCU mode, but that
could happen only in a very contrieved setup. Not worth
trying to do anything fancy here unless ->d_revalidate()
stops kicking out of RCU mode at least in some cases.
Reviewed-by: Christian Brauner <brauner@kernel.org>
Acked-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
->permission(), ->get_link() and ->inode_get_acl() might dereference
->s_fs_info (and, in case of ->permission(), ->s_fs_info->fc->user_ns
as well) when called from rcu pathwalk.
Freeing ->s_fs_info->fc is rcu-delayed; we need to make freeing ->s_fs_info
and dropping ->user_ns rcu-delayed too.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
makes proc_pid_ns() safe from rcu pathwalk (put_pid_ns()
is still synchronous, but that's not a problem - it does
rcu-delay everything that needs to be)
Reviewed-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
that keeps both around until struct inode is freed, making access
to them safe from rcu-pathwalk
Acked-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
NFS ->d_revalidate(), ->permission() and ->get_link() need to access
some parts of nfs_server when called in RCU mode:
server->flags
server->caps
*(server->io_stats)
and, worst of all, call
server->nfs_client->rpc_ops->have_delegation
(the last one - as NFS_PROTO(inode)->have_delegation()). We really
don't want to RCU-delay the entire nfs_free_server() (it would have
to be done with schedule_work() from RCU callback, since it can't
be made to run from interrupt context), but actual freeing of
nfs_server and ->io_stats can be done via call_rcu() just fine.
nfs_client part is handled simply by making nfs_free_client() use
kfree_rcu().
Acked-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
nfs_set_verifier() relies upon dentry being pinned; if that's
the case, grabbing ->d_lock stabilizes ->d_parent and guarantees
that ->d_parent points to a positive dentry. For something
we'd run into in RCU mode that is *not* true - dentry might've
been through dentry_kill() just as we grabbed ->d_lock, with
its parent going through the same just as we get to into
nfs_set_verifier_locked(). It might get to detaching inode
(and zeroing ->d_inode) before nfs_set_verifier_locked() gets
to fetching that; we get an oops as the result.
That can happen in nfs{,4} ->d_revalidate(); the call chain in
question is nfs_set_verifier_locked() <- nfs_set_verifier() <-
nfs_lookup_revalidate_delegated() <- nfs{,4}_do_lookup_revalidate().
We have checked that the parent had been positive, but that's
done before we get to nfs_set_verifier() and it's possible for
memory pressure to pick our dentry as eviction candidate by that
time. If that happens, back-to-back attempts to kill dentry and
its parent are quite normal. Sure, in case of eviction we'll
fail the ->d_seq check in the caller, but we need to survive
until we return there...
Acked-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
In __afs_break_callback() we might check ->cb_nr_mmap and if it's non-zero
do queue_work(&vnode->cb_work). In afs_drop_open_mmap() we decrement
->cb_nr_mmap and do flush_work(&vnode->cb_work) if it reaches zero.
The trouble is, there's nothing to prevent __afs_break_callback() from
seeing ->cb_nr_mmap before the decrement and do queue_work() after both
the decrement and flush_work(). If that happens, we might be in trouble -
vnode might get freed before the queued work runs.
__afs_break_callback() is always done under ->cb_lock, so let's make
sure that ->cb_nr_mmap can change from non-zero to zero while holding
->cb_lock (the spinlock component of it - it's a seqlock and we don't
need to mess with the counter).
Acked-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
->d_hash() and ->d_compare() use those, so we need to delay freeing
them.
Reviewed-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
That stuff can be accessed by ->d_hash()/->d_compare(); as it is, we have
a hard-to-hit UAF if rcu pathwalk manages to get into ->d_hash() on a filesystem
that is in process of getting shut down.
Besides, having nls and upcase table cleanup moved from ->put_super() towards
the place where sbi is freed makes for simpler failure exits.
Acked-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
one of the flags in it is used by ->d_hash()/->d_compare()
Reviewed-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
If lazy call of ->permission() returns a hard error, check that
try_to_unlazy() succeeds before returning it. That both makes
life easier for ->permission() instances and closes the race
in ENOTDIR handling - it is possible that positive d_can_lookup()
seen in link_path_walk() applies to the state *after* unlink() +
mkdir(), while nd->inode matches the state prior to that.
Normally seeing e.g. EACCES from permission check in rcu pathwalk
means that with some timings non-rcu pathwalk would've run into
the same; however, running into a non-executable regular file
in the middle of a pathname would not get to permission check -
it would fail with ENOTDIR instead.
Reviewed-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Avoids fun races in RCU pathwalk... Same goes for freeing LSM shite
hanging off super_block's arse.
Reviewed-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
check_snapshot() copies the bch_snapshot to a temporary to easily handle
older versions that don't have all the fields of the current version,
but it lacked a min() to correctly handle keys newer and larger than the
current version.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
If a journal write errored, the list of devices it was written to could
be empty - we're not supposed to mark an empty replicas list.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
bch2_direct_IO_read() checks the request offset and size for sector
alignment and then falls through to a couple calculations to shrink
the size of the request based on the inode size. The problem is that
these checks round up to the fs block size, which runs the risk of
underflowing iter->count if the block size happens to be large
enough. This is triggered by fstest generic/361 with a 4k block
size, which subsequently leads to a crash. To avoid this crash,
check that the shorten length doesn't exceed the overall length of
the iter.
Fixes:
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Su Yue <glass.su@suse.com>
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
If we're in FILTER_SNAPSHOTS mode and we start scanning a range of the
keyspace where no keys are visible in the current snapshot, we have a
problem - we'll scan for a very long time before scanning terminates.
Awhile back, this was fixed for most cases with peek_upto() (and
assertions that enforce that it's being used).
But the fix missed the fact that the inodes btree is different - every
key offset is in a different snapshot tree, not just the inode field.
Fixes:
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
Recently, we fixed our __GFP_NOFAIL usage in the readahead path, but the
easy one in read_single_folio() (where wa can return an error) was
missed - oops.
Fixes:
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
- Fix a crash when hot adding a PCI device to an LPAR since recent changes.
- Fix nested KVM level-2 guest reboot failure due to empty 'arch_compat'.
Thanks to: Amit Machhiwal, Aneesh Kumar K.V (IBM), Brian King, Gaurav Batra,
Vaibhav Jain.
-----BEGIN PGP SIGNATURE-----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=+tcX
-----END PGP SIGNATURE-----
Merge tag 'powerpc-6.8-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- Fix a crash when hot adding a PCI device to an LPAR since
recent changes
- Fix nested KVM level-2 guest reboot failure due to empty
'arch_compat'
Thanks to Amit Machhiwal, Aneesh Kumar K.V (IBM), Brian King, Gaurav
Batra, and Vaibhav Jain.
* tag 'powerpc-6.8-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
KVM: PPC: Book3S HV: Fix L2 guest reboot failure due to empty 'arch_compat'
powerpc/pseries/iommu: DLPAR add doesn't completely initialize pci_controller
Including:
- Intel VT-d fixes for nested domain handling:
- Cache invalidation for changes in a parent domain
- Dirty tracking setting for parent and nested domains
- Fix a constant-out-of-range warning
- ARM SMMU fixes:
- Fix CD allocation from atomic context when using SVA with SMMUv3
- Revert the conversion of SMMUv2 to domain_alloc_paging(), as it
breaks the boot for Qualcomm MSM8996 devices
- Restore SVA handle sharing in core code as it turned out there are
still drivers relying on it
-----BEGIN PGP SIGNATURE-----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=aVOB
-----END PGP SIGNATURE-----
Merge tag 'iommu-fixes-v6.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu fixes from Joerg Roedel:
- Intel VT-d fixes for nested domain handling:
- Cache invalidation for changes in a parent domain
- Dirty tracking setting for parent and nested domains
- Fix a constant-out-of-range warning
- ARM SMMU fixes:
- Fix CD allocation from atomic context when using SVA with SMMUv3
- Revert the conversion of SMMUv2 to domain_alloc_paging(), as it
breaks the boot for Qualcomm MSM8996 devices
- Restore SVA handle sharing in core code as it turned out there are
still drivers relying on it
* tag 'iommu-fixes-v6.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/sva: Restore SVA handle sharing
iommu/arm-smmu-v3: Do not use GFP_KERNEL under as spinlock
iommu/vt-d: Fix constant-out-of-range warning
iommu/vt-d: Set SSADE when attaching to a parent with dirty tracking
iommu/vt-d: Add missing dirty tracking set for parent domain
iommu/vt-d: Wrap the dirty tracking loop to be a helper
iommu/vt-d: Remove domain parameter for intel_pasid_setup_dirty_tracking()
iommu/vt-d: Add missing device iotlb flush for parent domain
iommu/vt-d: Update iotlb in nested domain attach
iommu/vt-d: Add missing iotlb flush for parent domain
iommu/vt-d: Add __iommu_flush_iotlb_psi()
iommu/vt-d: Track nested domains in parent
Revert "iommu/arm-smmu: Convert to domain_alloc_paging()"
- Fix NUMA initialization from ACPI CEDT.CFMWS
- Fix region assembly failures due to async init order
- Fix / simplify export of qos_class information
- Fix cxl_acpi initialization vs single-window-init failures
- Fix handling of repeated 'pci_channel_io_frozen' notifications
- Workaround platforms that violate host-physical-address ==
system-physical address assumptions
- Defer CXL CPER notification handling to v6.9
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQSbo+XnGs+rwLz9XGXfioYZHlFsZwUCZdpH9gAKCRDfioYZHlFs
ZwZlAQDE+PxTJnjCXDVnDylVF4yeJF2G/wSkH1CFVFVxa0OjhAD/ZFScS/nz/76l
1IYYiiLqmVO5DdmJtfKtq16m7e1cZwc=
=PuPF
-----END PGP SIGNATURE-----
Merge tag 'cxl-fixes-6.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/cxl/cxl
Pull cxl fixes from Dan Williams:
"A collection of significant fixes for the CXL subsystem.
The largest change in this set, that bordered on "new development", is
the fix for the fact that the location of the new qos_class attribute
did not match the Documentation. The fix ends up deleting more code
than it added, and it has a new unit test to backstop basic errors in
this interface going forward. So the "red-diff" and unit test saved
the "rip it out and try again" response.
In contrast, the new notification path for firmware reported CXL
errors (CXL CPER notifications) has a locking context bug that can not
be fixed with a red-diff. Given where the release cycle stands, it is
not comfortable to squeeze in that fix in these waning days. So, that
receives the "back it out and try again later" treatment.
There is a regression fix in the code that establishes memory NUMA
nodes for platform CXL regions. That has an ack from x86 folks. There
are a couple more fixups for Linux to understand (reassemble) CXL
regions instantiated by platform firmware. The policy around platforms
that do not match host-physical-address with system-physical-address
(i.e. systems that have an address translation mechanism between the
address range reported in the ACPI CEDT.CFMWS and endpoint decoders)
has been softened to abort driver load rather than teardown the memory
range (can cause system hangs). Lastly, there is a robustness /
regression fix for cases where the driver would previously continue in
the face of error, and a fixup for PCI error notification handling.
Summary:
- Fix NUMA initialization from ACPI CEDT.CFMWS
- Fix region assembly failures due to async init order
- Fix / simplify export of qos_class information
- Fix cxl_acpi initialization vs single-window-init failures
- Fix handling of repeated 'pci_channel_io_frozen' notifications
- Workaround platforms that violate host-physical-address ==
system-physical address assumptions
- Defer CXL CPER notification handling to v6.9"
* tag 'cxl-fixes-6.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/cxl/cxl:
cxl/acpi: Fix load failures due to single window creation failure
acpi/ghes: Remove CXL CPER notifications
cxl/pci: Fix disabling memory if DVSEC CXL Range does not match a CFMWS window
cxl/test: Add support for qos_class checking
cxl: Fix sysfs export of qos_class for memdev
cxl: Remove unnecessary type cast in cxl_qos_class_verify()
cxl: Change 'struct cxl_memdev_state' *_perf_list to single 'struct cxl_dpa_perf'
cxl/region: Allow out of order assembly of autodiscovered regions
cxl/region: Handle endpoint decoders in cxl_region_find_decoder()
x86/numa: Fix the sort compare func used in numa_fill_memblks()
x86/numa: Fix the address overlap check in numa_fill_memblks()
cxl/pci: Skip to handle RAS errors if CXL.mem device is detached
they recheck in the error path.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEJfWUX4UqZ4x1O2wixSPxCi2dA1oFAmXaEswACgkQxSPxCi2d
A1oT2Qf/c1opgjRUe+yY/v7nWf4paufSj2O4LYAy/qQBU7IS9CcXQPzi/pKlfEo8
60OZfa5gfrCAla79se7hHI/mxReq7CI5nFvYDyqQ1JZQ/djG/4cN/oWf5fQ12pon
/ET1IzaZ+Mom+5wDBeQBLoQwXTA1ru5Bi1OiUe9Ed3wzadZQQks5s65fPnc0emGJ
ClyaXiiCt4Dy36E5GmuPpmPB4ZJ57SwcnFWDFIeCHEbIQk36APkZ22z7lqGObjw2
ANO1l59k6ojzmaXLi9pw/J/o/qyfNR0MpeI7SpmtJzhSZKeGKsUX2GlJ9QBhViJp
XL/+7MbSRJ43IY1lomoHZm1vxe0aPg==
=sQPX
-----END PGP SIGNATURE-----
Merge tag 'for-6.8/dm-fix-3' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fix from Mike Snitzer:
- Fix DM integrity and verity targets to not use excessive stack when
they recheck in the error path.
* tag 'for-6.8/dm-fix-3' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm-integrity, dm-verity: reduce stack usage for recheck
Six fixes: the four driver ones are pretty trivial. The larger two
core changes are to try to fix various USB attached devices which have
somewhat eccentric ways of handling the VPD and other mode pages which
necessitate multiple revalidates (that were removed in the interests
of efficiency) and updating the heuristic for supported VPD pages.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCZdkyyyYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishS2KAP0V8RVm
U1gUoE4doIV9WdK8Dv0MUxnOpYVvjhRjM8PA1QEAwaPJivC91smxJv4MOIDq0PL3
9qyMwQq4jWH/2zS14p8=
=8aq+
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Six fixes: the four driver ones are pretty trivial.
The larger two core changes are to try to fix various USB attached
devices which have somewhat eccentric ways of handling the VPD and
other mode pages which necessitate multiple revalidates (that were
removed in the interests of efficiency) and updating the heuristic for
supported VPD pages"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: jazz_esp: Only build if SCSI core is builtin
scsi: smartpqi: Fix disable_managed_interrupts
scsi: ufs: Uninitialized variable in ufshcd_devfreq_target()
scsi: target: pscsi: Fix bio_put() for error case
scsi: core: Consult supported VPD page list prior to fetching page
scsi: sd: usb_storage: uas: Access media prior to querying device properties
-----BEGIN PGP SIGNATURE-----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=QxF6
-----END PGP SIGNATURE-----
Merge tag 'i2c-for-6.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fix from Wolfram Sang:
"A bugfix for host drivers"
* tag 'i2c-for-6.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: imx: when being a target, mark the last read as processed
The newly added integrity_recheck() function has another larger stack
allocation, just like its caller integrity_metadata(). When it gets
inlined, the combination of the two exceeds the warning limit for 32-bit
architectures and possibly risks an overflow when this is called from
a deep call chain through a file system:
drivers/md/dm-integrity.c:1767:13: error: stack frame size (1048) exceeds limit (1024) in 'integrity_metadata' [-Werror,-Wframe-larger-than]
1767 | static void integrity_metadata(struct work_struct *w)
Since the caller at this point is done using its checksum buffer,
just reuse the same buffer in the new function to avoid the double
allocation.
[Mikulas: add "noinline" to integrity_recheck and verity_recheck.
These functions are only called on error, so they shouldn't bloat the
stack frame or code size of the caller.]
Fixes: c88f5e553f ("dm-integrity: recheck the integrity tag after a failure")
Fixes: 9177f3c0de ("dm-verity: recheck the hash after a failure")
Cc: stable@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
When being a target, NAK from the controller means that all bytes have
been transferred. So, the last byte needs also to be marked as
'processed'. Otherwise index registers of backends may not increase.
Fixes: f7414cd692 ("i2c: imx: support slave mode for imx I2C driver")
Signed-off-by: Corey Minyard <minyard@acm.org>
Tested-by: Andrew Manley <andrew.manley@sealingtech.com>
Reviewed-by: Andrew Manley <andrew.manley@sealingtech.com>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
[wsa: fixed comment and commit message to properly describe the case]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
- Fix CPU hotplug
- Fix unaligned accesses and faults in stack unwinder
- Fix potential build errors by always including asm-generic/kprobes.h
- Fix build bug by add missing CONFIG_DYNAMIC_FTRACE check
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQS86RI+GtKfB8BJu973ErUQojoPXwUCZdjO+gAKCRD3ErUQojoP
X5QiAPsGd0pv/I5HXc/JkwnqBaP7RC1BwN01og4ftzmKG8ngvQD+JH4YT2rvT7c0
0FgUVp5khg0ZgSZ6IGUFy7GUs8uanww=
=XdOQ
-----END PGP SIGNATURE-----
Merge tag 'parisc-for-6.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc architecture fixes from Helge Deller:
"Fixes CPU hotplug, the parisc stack unwinder and two possible build
errors in kprobes and ftrace area:
- Fix CPU hotplug
- Fix unaligned accesses and faults in stack unwinder
- Fix potential build errors by always including asm-generic/kprobes.h
- Fix build bug by add missing CONFIG_DYNAMIC_FTRACE check"
* tag 'parisc-for-6.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Fix stack unwinder
parisc/kprobes: always include asm-generic/kprobes.h
parisc/ftrace: add missing CONFIG_DYNAMIC_FTRACE check
Revert "parisc: Only list existing CPUs in cpu_possible_mask"
