For 5000 and 6000g2b series of devices, use long monitor timer to check
stuck tx queues.
.6000g2b series device, it is WiFi/BT combo device, there are some cases,
tx queues are not move for a period of time because the WiFi/BT coex.
.5000 series device, it is being reported firmware got reload more
often than necessary, so extend the timer to avoid un-necessary reload.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Change the name for monitor timer, also adding define for long monitor
timer; long monitor timer can be used for the type of devices require longer
time to determine the uCode is stuck on tx and needed reload.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Atheros PCIe wireless cards handled by ath5k do require L0s disabled.
For distributions shipping with CONFIG_PCIEASPM (this will be enabled
by default in the future in 2.6.36) this will also mean both L1 and L0s
will be disabled when a pre 1.1 PCIe device is detected. We do know L1
works correctly even for all ath5k pre 1.1 PCIe devices though but cannot
currently undue the effect of a blacklist, for details you can read
pcie_aspm_sanity_check() and see how it adjusts the device link
capability.
It may be possible in the future to implement some PCI API to allow
drivers to override blacklists for pre 1.1 PCIe but for now it is
best to accept that both L0s and L1 will be disabled completely for
distributions shipping with CONFIG_PCIEASPM rather than having this
issue present. Motivation for adding this new API will be to help
with power consumption for some of these devices.
Example of issues you'd see:
- On the Acer Aspire One (AOA150, Atheros Communications Inc. AR5001
Wireless Network Adapter [168c:001c] (rev 01)) doesn't work well
with ASPM enabled, the card will eventually stall on heavy traffic
with often 'unsupported jumbo' warnings appearing. Disabling
ASPM L0s in ath5k fixes these problems.
- On the same card you would see a storm of RXORN interrupts
even though medium is idle.
Credit for root causing and fixing the bug goes to Jussi Kivilinna.
Cc: David Quan <David.Quan@atheros.com>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Tim Gardner <tim.gardner@canonical.com>
Cc: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch handles the firmware loading properly
for device ID 7015.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use appropriate command (CMD_TRIGGER_SCAN_TO) instead of scan command
(CMD_SCAN) to configure trigger scan timeout.
This was broken in commit 3a98c30f3e.
This fix address the bug reported here:
https://bugzilla.kernel.org/show_bug.cgi?id=16554
Cc: stable@kernel.org
Signed-off-by: Yuri Ershov <ext-yuri.ershov@nokia.com>
Signed-off-by: Yuri Kululin <ext-yuri.kululin@nokia.com>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some APs advertise that they may be HT40 capable in the capabilites
but the current operating channel configuration may be only HT20.
This causes disconnection as ath9k_htc sets WLAN_RC_40_FLAG despite
the AP operating in HT20 mode.
Hence set this flag only if the current channel configuration
is HT40 enabled.
Cc: stable@kernel.org
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently the driver will try to protect all frames,
which leads to a lot of odd things like sending an
RTS with a zeroed RA before multicast frames, which
is clearly bogus.
In order to fix all of this, we need to take a step
back and see what we need to achieve:
* we need RTS/CTS protection if requested by
the AP for the BSS, mac80211 tells us this
* in that case, CTS-to-self should only be
enabled when mac80211 tells us
* additionally, as a hardware workaround, on
some devices we have to protect aggregated
frames with RTS
To achieve the first two items, set up the RXON
accordingly and set the protection required flag
in the transmit command when mac80211 requests
protection for the frame.
To achieve the last item, set the rate-control
RTS-requested flag for all stations that we have
aggregation sessions with, and set the protection
required flag when sending aggregated frames (on
those devices where this is required).
Since otherwise bugs can occur, do not allow the
user to override the RTS-for-aggregation setting
from sysfs any more.
Finally, also clean up the way all these flags get
set in the driver and move everything into the
device-specific functions.
Cc: stable@kernel.org [2.6.35]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CC [M] drivers/net/wireless/libertas/cfg.o
/home/greearb/git/wireless-testing/drivers/net/wireless/libertas/cfg.c: In function ‘lbs_scan_worker’:
/home/greearb/git/wireless-testing/drivers/net/wireless/libertas/cfg.c:722: error: ‘TASK_NORMAL’ undeclared (first use in this function)
/home/greearb/git/wireless-testing/drivers/net/wireless/libertas/cfg.c:722: error: (Each undeclared identifier is reported only once
/home/greearb/git/wireless-testing/drivers/net/wireless/libertas/cfg.c:722: error: for each function it appears in.)
/home/greearb/git/wireless-testing/drivers/net/wireless/libertas/cfg.c: In function ‘lbs_cfg_connect’:
/home/greearb/git/wireless-testing/drivers/net/wireless/libertas/cfg.c:1267: error: ‘TASK_INTERRUPTIBLE’ undeclared (first use in this function)
/home/greearb/git/wireless-testing/drivers/net/wireless/libertas/cfg.c:1267: error: implicit declaration of function ‘signal_pending’
/home/greearb/git/wireless-testing/drivers/net/wireless/libertas/cfg.c:1267: error: implicit declaration of function ‘schedule_timeout’
Reported-by: Ben Greear <greearb@candelatech.com>
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit 5f7aebd845.
Apparently, that PCI ID data was incorrectly taken from the subsystem
information. The actual ID matches another already known ID.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
spin_is_locked() can return zero on some (UP?)
configurations because locks don't exist, and
that causes an endless amount of warnings. Use
lockdep_assert_held() instead, which has two
advantages:
1) it verifies the current task is holding
the lock or mutex
2) it compiles away completely when lockdep
is not enabled
Cc: stable@kernel.org [2.6.34+, maybe only parts of patch]
Reported-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The TX tracing code copies with the wrong length,
which will typically copy too little data. Fix
this by using the correct length variable.
Cc: stable@kernel.org [2.6.32+]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix this leftover TODO from the cfg80211 conversion by doing a scan
if cfg80211 didn't pass in the BSSID for us. Since the scan code
uses so much of the cfg80211_scan_request structure to build up the
firmware command, we just fake one when the scan request is triggered
internally. But we need to make sure that internal 'fake' cfg82011
scan request does not get back to cfg82011 via cfg80211_scan_done().
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some APs get pissy if you don't send the firmware the extended rates
in the association request's rates TLV. Found this on a Linksys
WRT54G v2; it denies association with status code 18 unless you
add the extended rates too. The old driver did this, but it got
lost in the cfg80211 conversion.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Let's actually check the right field in the command response; and
if there aren't any reported BSSes, exit early with success.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
82ca934176 added scary looking
but harmless error messages. Make them clearer and make the
actual failure message show up with the same severity as the
harmless one.
Signed-off-by: Andy Lutomirski <luto@mit.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
IRQ and resource[] may not have correct values until
after PCI hotplug setup occurs at pci_enable_device() time.
The semantic match that finds this problem is as follows:
// <smpl>
@@
identifier x;
identifier request ~= "pci_request.*|pci_resource.*";
@@
(
* x->irq
|
* x->resource
|
* request(x, ...)
)
...
*pci_enable_device(x)
// </smpl>
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If kzalloc() fails return with -ENOMEM from ipw2100_net_init() which is
called by register_netdev.
CC: Dan Carpenter <error27@gmail.com>
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_rx_skb_preprocess nulls rxs and the mactime is never set again -
mactime is always 0. This causes problems in IBSS mode.
ieee80211_rx_bss_info uses mactime to decide if an IBSS merge is needed.
Without this patch the merge is triggered by each beacon received.
This can be recognized by the "beacon TSF higher than local TSF - IBSS
merge with BSSID" log message accompanying each beacon.
This problem was not completely fixed in commit
a6d2055b02 and is not a stable kernel fix.
It is solely intended for wireless-testing.
Signed-off-by: Jan Friedrich <jft@dev2day.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The SMC2802W appears to work with p54pci.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested-by: David Cozatt <olbrannon@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I noticed a possible issue in the paused flag management of the
ath_atx_tid data structure. In particular, in a noisy environment and
under heavy load, I observed that the AGGR session establishment could
fail several times consecutively causing values of the paused flag
greater than one for this TID (ath_tx_pause_tid is called more than
once from ath_tx_aggr_start).
Considering that the session for this TID can not be established also
after the mac80211 stack calls the ieee80211_agg_tx_operational() since
the ath_tx_aggr_resume() lowers the paused flag only by one.
This patch also replaces some BUG_ON calls with WARN_ON, as even if
these unlikely conditions happen, it's not fatal enough to justify a
BUG_ON.
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR9003 was not relying on the CTL indexes from the EEPROM for capping the
max output power. The CTL indexes from the EEPROM provide calibrated
limits for output power for each tested and supported frequency. Without
this the device operates at a power level which only conforms to the
transmit spectrum mask as specified by IEEE Annex I.2.3.
The regulatory limit by CRDA is always used but does not provide
calibrated values for optimal performance, specially on band edges.
Using the calibrated data from the EEPROM ensures the device
operates at optimal output power while still ensuring proper
regulatory compliance. The device uses the minimum of these tree
values, the value from CRDA, the calibrated value from CTL indexex,
and the value to conform to the IEEE transmit spectrum mask.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
wl1271_dump() uses cmd after kfree(cmd). Move kfree() just after
wl1271_dump().
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Acked-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
small typo fix in ucode_bt_stats_read debugfs file
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is a uCode bug which cause the tx queue id not match scd_flow
in compressed block ack frame, and it need to be addressed in uCode.
Currently, driver will log the information when it happen.
Since it is possible happen very often and we do not want to fill the syslog,
so don't enable the logging by default.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When iwlwifi is compiled w/o debug, we get
this warning:
iwl-agn.c: In function ‘iwlagn_load_firmware’:
iwl-agn.c:2014: warning: passing argument 3 of ‘iwl_print_hex_dump’ discards qualifiers from pointer target type
iwl-debug.h:73: note: expected ‘void *’ but argument is of type ‘const u8 *’
because the const qualifier is missing in the
inline stub. Fix this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On AR5008-AR9002, other forms of calibration must not be started while
the noise floor calibration is running, as this can create invalid
readings which were sometimes not even recoverable by any further
calibration attempts.
This patch also ensures that the result of noise floor measurements
are processed faster and also allows the result of the initial
calibration on reset to make it into the NF history buffer
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The noise floor history buffer is currently not kept per channel, which
can lead to problems when changing channels from a clean channel to a
noisy one. Also when switching from HT20 to HT40, the noise floor
history buffer is full of measurements, but none of them contain data
for the extension channel, which it needs quite a bit of time to recover
from.
This patch puts all the per-channel calibration data into a single data
structure, and gives the the driver control over whether that is used
per-channel or even not used for some channels.
For ath9k_htc, I decided to keep this per-channel in order to avoid
creating regressions.
For ath9k, the data is kept only for the operating channel, which saves
some space. ath9k_hw takes care of wiping old data when the operating
channel or its channel flags change.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Previously the software scan callback was used to indicate to the hardware,
when it was safe to calibrate. This didn't really work properly, because it
depends on a specific order of software scan callbacks vs. channel changes.
Also, software scans are not the only thing that triggers off-channel
activity, so it's better to use the newly added indication from mac80211 for
this and not use the software scan callback for anything calibration related.
This fixes at least some of the invalid noise floor readings that I've seen
in AP mode on AR9160
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Writes to the analog shift registers, which are issues by the initval
programming function, require a 100 usec delay (similar to AR9002,
but in a different register range).
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When updating the PAPRD table in hardware, PAPRD itself needs to be
disabled first, otherwise the hardware can throw a data bus error,
which upsets at least some platforms.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The periodic noise floor calibration is broken on this chip family, because
it keeps triggering a software-filtered noise floor calibration, but never
reads the result before uploading the history buffer value to the hardware.
Fix this with a call to ath9k_hw_getnf(), just like on AR9002.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On AR9003 the initial noise floor calibration is currently triggered
at the end of the reset without allowing the hardware to update the
baseband settings. This could potentially make scans in noisy
environments a bit more unreliable, so use the same calibration
sequence that is used on AR9002.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
commit f84b29ec0a
Author: Johannes Berg <johannes.berg@intel.com>
Date: Tue May 18 02:29:13 2010 -0700
iwlwifi: queue user-initiated scan when doing internal scan
introduced a potential deadlock because it calls
ieee80211_scan_completed() with the priv->mutex
held, but mac80211 may call back into iwlwifi
which would lead to recursive locking. Move this
out from under the mutex.
Cc: stable@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1443 commits)
phy/marvell: add 88ec048 support
igb: Program MDICNFG register prior to PHY init
e1000e: correct MAC-PHY interconnect register offset for 82579
hso: Add new product ID
can: Add driver for esd CAN-USB/2 device
l2tp: fix export of header file for userspace
can-raw: Fix skb_orphan_try handling
Revert "net: remove zap_completion_queue"
net: cleanup inclusion
phy/marvell: add 88e1121 interface mode support
u32: negative offset fix
net: Fix a typo from "dev" to "ndev"
igb: Use irq_synchronize per vector when using MSI-X
ixgbevf: fix null pointer dereference due to filter being set for VLAN 0
e1000e: Fix irq_synchronize in MSI-X case
e1000e: register pm_qos request on hardware activation
ip_fragment: fix subtracting PPPOE_SES_HLEN from mtu twice
net: Add getsockopt support for TCP thin-streams
cxgb4: update driver version
cxgb4: add new PCI IDs
...
Manually fix up conflicts in:
- drivers/net/e1000e/netdev.c: due to pm_qos registration
infrastructure changes
- drivers/net/phy/marvell.c: conflict between adding 88ec048 support
and cleaning up the IDs
- drivers/net/wireless/ipw2x00/ipw2100.c: trivial ipw2100_pm_qos_req
conflict (registration change vs marking it static)
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6:
PM / Runtime: Add runtime PM statistics (v3)
PM / Runtime: Make runtime_status attribute not debug-only (v. 2)
PM: Do not use dynamically allocated objects in pm_wakeup_event()
PM / Suspend: Fix ordering of calls in suspend error paths
PM / Hibernate: Fix snapshot error code path
PM / Hibernate: Fix hibernation_platform_enter()
pm_qos: Get rid of the allocation in pm_qos_add_request()
pm_qos: Reimplement using plists
plist: Add plist_last
PM: Make it possible to avoid races between wakeup and system sleep
PNPACPI: Add support for remote wakeup
PM: describe kernel policy regarding wakeup defaults (v. 2)
PM / Hibernate: Fix typos in comments in kernel/power/swap.c
Fix possible double priv->mutex lock introduced by commit
a69b03e941
"iwlwifi: cancel scan watchdog in iwl_bg_abort_scan" .
We can not call cancel_delayed_work_sync(&priv->scan_check) with
priv->mutex locked because workqueue function iwl_bg_scan_check()
take that lock internally.
We do not need to synchronize when canceling priv->scan_check work.
We can avoid races (sending double abort command or send no
command at all) using STATUS_SCAN_ABORT bit. Moreover
current iwl_bg_scan_check() code seems to be broken, as
we should not send abort commands when currently aborting.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
CC: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes the information available through ethtool...
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Acked-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
This makes the information available through ethtool...
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Acked-by: Kalle Valo <kvalo@adurom.com>
