There's no need to run all the code on mt7530_setup_port5() if port 5 is
disabled. The only case for calling mt7530_setup_port5() from
mt7530_setup() is when PHY muxing is enabled. That is because port 5 is not
defined as a port on the devicetree, therefore, it cannot be controlled by
phylink.
Because of this, run mt7530_setup_port5() if priv->p5_intf_sel is
P5_INTF_SEL_PHY_P0 or P5_INTF_SEL_PHY_P4. Remove the P5_DISABLED case from
mt7530_setup_port5().
Stop initialising the interface variable as the remaining cases will always
call mt7530_setup_port5() with it initialised.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20240122-for-netnext-mt7530-improvements-1-v3-7-042401f2b279@arinc9.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Running mt7530_setup_port5() from mt7530_setup() used to handle all cases
of configuring port 5, including phylink.
Setting priv->p5_interface under mt7530_setup_port5() makes sure that
mt7530_setup_port5() from mt753x_phylink_mac_config() won't run.
The commit ("net: dsa: mt7530: improve code path for setting up port 5")
makes so that mt7530_setup_port5() from mt7530_setup() runs only on
non-phylink cases.
Get rid of unnecessarily setting priv->p5_interface under
mt7530_setup_port5() as port 5 phylink configuration will be done by
running mt7530_setup_port5() from mt753x_phylink_mac_config() now.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20240122-for-netnext-mt7530-improvements-1-v3-6-042401f2b279@arinc9.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There're two code paths for setting up port 5:
mt7530_setup()
-> mt7530_setup_port5()
mt753x_phylink_mac_config()
-> mt753x_mac_config()
-> mt7530_mac_config()
-> mt7530_setup_port5()
Currently mt7530_setup_port5() from mt7530_setup() always runs. If port 5
is used as a CPU, DSA, or user port, mt7530_setup_port5() from
mt753x_phylink_mac_config() won't run. That is because priv->p5_interface
set on mt7530_setup_port5() will match state->interface on
mt753x_phylink_mac_config() which will stop running mt7530_setup_port5()
again.
Therefore, mt7530_setup_port5() will never run from
mt753x_phylink_mac_config().
Address this by not running mt7530_setup_port5() from mt7530_setup() if
port 5 is used as a CPU, DSA, or user port. This driver isn't in the
dsa_switches_apply_workarounds[] array so phylink will always be present.
To keep the cases where port 5 isn't controlled by phylink working as
before, preserve the mt7530_setup_port5() call from mt7530_setup().
Do not set priv->p5_intf_sel to P5_DISABLED. It is already set to that when
"priv" is allocated.
Move setting the interface to a more specific location. It's supposed to be
overwritten if PHY muxing is detected.
Improve the comment which explains the process.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20240122-for-netnext-mt7530-improvements-1-v3-5-042401f2b279@arinc9.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There's no logic to numerically order the CPU ports. Just state the port
number instead.
Remove the irrelevant PHY muxing information from
mt7530_mac_port_get_caps(). Explain the supported MII modes instead.
Remove the out of place PHY muxing information from
mt753x_phylink_mac_config(). The function is for MT7530, MT7531, and the
switch on the MT7988 SoC but there's no PHY muxing on MT7531 or the switch
on the MT7988 SoC.
These comments were gradually introduced with the commits below.
commit ca366d6c88 ("net: dsa: mt7530: Convert to PHYLINK API")
commit 38f790a805 ("net: dsa: mt7530: Add support for port 5")
commit 88bdef8be9 ("net: dsa: mt7530: Extend device data ready for adding
a new hardware")
commit c288575f78 ("net: dsa: mt7530: Add the support of MT7531 switch")
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Acked-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20240122-for-netnext-mt7530-improvements-1-v3-4-042401f2b279@arinc9.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Introduce the p5_sgmii field to store the information for whether port 5
has got SGMII or not. Instead of reading the MT7531_TOP_SIG_SR register
multiple times, the register will be read once and the value will be
stored on the p5_sgmii field. This saves unnecessary reads of the
register.
Move the comment about MT7531AE and MT7531BE to mt7531_setup(), where the
switch is identified.
Get rid of mt7531_dual_sgmii_supported() now that priv->p5_sgmii stores the
information. Address the code where mt7531_dual_sgmii_supported() is used.
Get rid of mt7531_is_rgmii_port() which just prints the opposite of
priv->p5_sgmii.
Instead of calling mt7531_pll_setup() then returning, do not call it if
port 5 is SGMII.
Remove P5_INTF_SEL_GMAC5_SGMII. The p5_interface_select enum is supposed to
represent the mode that port 5 is being used in, not the hardware
information of port 5. Set p5_intf_sel to P5_INTF_SEL_GMAC5 instead, if
port 5 is not dsa_is_unused_port().
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Acked-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20240122-for-netnext-mt7530-improvements-1-v3-3-042401f2b279@arinc9.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use the p5_interface_select enumeration as the data type for the
p5_intf_sel field. This ensures p5_intf_sel can only take the values
defined in the p5_interface_select enumeration.
Remove the explicit assignment of 0 to P5_DISABLED as the first enum item
is automatically assigned 0.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Acked-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20240122-for-netnext-mt7530-improvements-1-v3-2-042401f2b279@arinc9.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On the MT7530 switch, the CPU_PORT field indicates which CPU port to trap
frames to, regardless of the affinity of the inbound user port.
When multiple CPU ports are in use, if the DSA conduit interface is down,
trapped frames won't be passed to the conduit interface.
To make trapping frames work including this case, implement
ds->ops->conduit_state_change() on this subdriver and set the CPU_PORT
field to the numerically smallest CPU port whose conduit interface is up.
Introduce the active_cpu_ports field to store the information of the active
CPU ports. Correct the macros, CPU_PORT is bits 4 through 6 of the
register.
Add a comment to explain frame trapping for this switch.
Currently, the driver doesn't support the use of multiple CPU ports so this
is not necessarily a bug fix.
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Suggested-by: Russell King (Oracle) <linux@armlinux.org.uk>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20240122-for-netnext-mt7530-improvements-1-v3-1-042401f2b279@arinc9.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Same patch as previous one, but for ebtables.
To build a kernel that only supports ebtables-nft, the builtin tables
need to be disabled, i.e.:
CONFIG_BRIDGE_EBT_BROUTE=n
CONFIG_BRIDGE_EBT_T_FILTER=n
CONFIG_BRIDGE_EBT_T_NAT=n
The ebtables specific extensions can then be used nftables'
NFT_COMPAT interface.
Signed-off-by: Florian Westphal <fw@strlen.de>
Add hidden IP(6)_NF_IPTABLES_LEGACY symbol.
When any of the "old" builtin tables are enabled the "old" iptables
interface will be supported.
To disable the old set/getsockopt interface the existing options
for the builtin tables need to be turned off:
CONFIG_IP_NF_IPTABLES=m
CONFIG_IP_NF_FILTER is not set
CONFIG_IP_NF_NAT is not set
CONFIG_IP_NF_MANGLE is not set
CONFIG_IP_NF_RAW is not set
CONFIG_IP_NF_SECURITY is not set
Same for CONFIG_IP6_NF_ variants.
This allows to build a kernel that only supports ip(6)tables-nft
(iptables-over-nftables api).
In the future the _LEGACY symbol will become visible and the select
statements will be turned into 'depends on', but for now be on safe side
so "make oldconfig" won't break things.
Signed-off-by: Florian Westphal <fw@strlen.de>
Allows to build kernel that supports the arptables mangle target
via nftables' compat infra but without the arptables get/setsockopt
interface or the old arptables filter interpreter.
IOW, setting IP_NF_ARPFILTER=n will break arptables-legacy, but
arptables-nft will continue to work as long as nftables compat
support is enabled.
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Phil Sutter <phil@nwl.cc>
Use the new KMEM_CACHE() macro instead of direct kmem_cache_create
to simplify the creation of SLAB caches.
Signed-off-by: Kunwu Chan <chentao@kylinos.cn>
Acked-by: Simon Horman <horms@kernel.org>
Signed-off-by: Florian Westphal <fw@strlen.de>
Use the new KMEM_CACHE() macro instead of direct kmem_cache_create
to simplify the creation of SLAB caches.
Signed-off-by: Kunwu Chan <chentao@kylinos.cn>
Signed-off-by: Florian Westphal <fw@strlen.de>
No need to refetch the flag from the netlink attribute, pass the
existing flags variable which already provide validated flags.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Florian Westphal <fw@strlen.de>
Allow a new process to take ownership of a previously owned table,
useful mostly for firewall management services restarting or suspending
when idle.
By extending __NFT_TABLE_F_UPDATE, the on/off/on check in
nf_tables_updtable() also covers table adoption, although it is actually
not needed: Table adoption is irreversible because nf_tables_updtable()
rejects attempts to drop NFT_TABLE_F_OWNER so table->nlpid setting can
happen just once within the transaction.
If the transaction commences, table's nlpid and flags fields are already
set and no further action is required. If it aborts, the table returns
to orphaned state.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Florian Westphal <fw@strlen.de>
This companion flag to NFT_TABLE_F_OWNER requests the kernel to keep the
table around after the process has exited. It marks such table as
orphaned (by dropping OWNER flag but keeping PERSIST flag in place),
which opens it for other processes to manipulate. For the sake of
simplicity, PERSIST flag may not be altered though.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Florian Westphal <fw@strlen.de>
Add at least this one-liner describing the obvious.
Fixes: 6001a930ce ("netfilter: nftables: introduce table ownership")
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Florian Westphal <fw@strlen.de>
We had to add another synchronize_rcu() in recent fix.
Bite the bullet and add an rcu_head to netdev_name_node,
free from RCU.
Note that name_node does not hold any reference on dev
to which it points, but there must be a synchronize_rcu()
on device removal path, so we should be fine.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TRF7970A is a SPI device, not I2C.
Signed-off-by: Tobias Schramm <t.schramm@manjaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RENESAS FemtoClock3 Wireless is a high-performance jitter attenuator,
frequency translator, and clock synthesizer. The device is comprised of 3
digital PLLs (DPLL) to track CLKIN inputs and three independent low phase
noise fractional output dividers (FOD) that output low phase noise clocks.
FemtoClock3 supports one Time Synchronization (Time Sync) channel to enable
an external processor to control the phase and frequency of the Time Sync
channel and to take phase measurements using the TDC. Intended applications
are synchronization using the precision time protocol (PTP) and
synchronization with 0.5 Hz and 1 Hz signals from GNSS.
Signed-off-by: Min Li <min.li.xe@renesas.com>
Acked-by: Lee Jones <lee@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change is for the PHC devices that can measure the phase offset
between PHC signal and the external signal, such as the 1PPS signal of
GNSS. Reporting PTP_CLOCK_EXTOFF to user space will be piggy-backed to
the existing ptp_extts_event so that application such as ts2phc can
poll the external offset the same way as extts. Hence, ts2phc can use
the offset to achieve the alignment between PHC and the external signal
by the help of either SW or HW filters.
Signed-off-by: Min Li <min.li.xe@renesas.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Breno Leitao says:
====================
Fix MODULE_DESCRIPTION() for net (p3)
There are hundreds of network modules that misses MODULE_DESCRIPTION(),
causing a warning when compiling with W=1. Example:
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/net/arcnet/com90io.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/net/arcnet/arc-rimi.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/net/arcnet/com20020.o
This part3 of the patchset focus on the missing ethernet drivers, which
is now warning free. This also fixes net/pcs and ieee802154.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
W=1 builds now warn if module is built without a MODULE_DESCRIPTION().
Add descriptions to arcnet module.
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
W=1 builds now warn if module is built without a MODULE_DESCRIPTION().
Add descriptions to ieee802154 modules.
Signed-off-by: Breno Leitao <leitao@debian.org>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
W=1 builds now warn if module is built without a MODULE_DESCRIPTION().
Add descriptions to the Lynx, XPCS and LynxI PCS drivers.
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
W=1 builds now warn if module is built without a MODULE_DESCRIPTION().
Add descriptions to the Beckhoff CX5020 EtherCAT Ethernet driver.
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
W=1 builds now warn if module is built without a MODULE_DESCRIPTION().
Add descriptions to the TI CPSW switch module.
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
W=1 builds now warn if module is built without a MODULE_DESCRIPTION().
Add descriptions to the STMicro DWMAC for Altera SOCs.
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
W=1 builds now warn if module is built without a MODULE_DESCRIPTION().
Add descriptions to the Qualcom rmnet and emac drivers.
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Subash Abhinov Kasiviswanathan <quic_subashab@quicinc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
W=1 builds now warn if module is built without a MODULE_DESCRIPTION().
Add descriptions to the SMSC 91x/911x/9420 Ethernet drivers.
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
W=1 builds now warn if module is built without a MODULE_DESCRIPTION().
Add descriptions to the Ocelot SoCs (VSC7514) helpers driver.
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
W=1 builds now warn if module is built without a MODULE_DESCRIPTION().
Add descriptions to the Microchip ENCX24J600 helpers driver.
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
As of now, the field TCA_TAPRIO_ATTR_FLAGS is being validated by manually
checking its value, using the function taprio_flags_valid().
With this patch, the field will be validated through the netlink policy
NLA_POLICY_MASK, where the mask is defined by TAPRIO_SUPPORTED_FLAGS.
The mutual exclusivity of the two flags TCA_TAPRIO_ATTR_FLAG_FULL_OFFLOAD
and TCA_TAPRIO_ATTR_FLAG_TXTIME_ASSIST is still checked manually.
Changes since RFC:
- fixed reversed xmas tree
- use NL_SET_ERR_MSG_MOD() for both invalid configuration
Changes since v1:
- Changed NL_SET_ERR_MSG_MOD to NL_SET_ERR_MSG_ATTR when wrong flags
issued
- Changed __u32 to u32
Changes since v2:
- Added the missing parameter for NL_SET_ERR_MSG_ATTR (sorry again for
the noise)
Signed-off-by: Alessandro Marcolini <alessandromarcolini99@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds hardware profile supports for extracting packet headers.
It makes sure that hardware is capabale of extracting ICMP, CPT, ERSPAN
headers.
Signed-off-by: Suman Ghosh <sumang@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiawen Wu says:
====================
Implement irq_domain for TXGBE
Implement irq_domain for the MAC interrupt and handle the sub-irqs.
v3 -> v4:
- fix build error
v2 -> v3:
- use macro defines instead of magic number
v1 -> v2:
- move interrupt codes to txgbe_irq.c
- add txgbe-link-irq to msic irq domain
- remove functions that are not needed
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In the current interrupt controller, the MAC interrupt acts as the
parent interrupt in the GPIO IRQ chip. But when the number of Rx/Tx
ring changes, the PCI IRQ vector needs to be reallocated. Then this
interrupt controller would be corrupted. So use irq_domain structure
to avoid the above problem.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to change the interrupt response structure, there will be a
lot of code added next. Move these interrupt codes to a new file, to
make the codes cleaner.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a note when using esw_port_metadata. The parameter has runtime
mode but setting it does not take effect immediately. Setting it must
happen in legacy mode, and the port metadata takes effects when the
switchdev mode is enabled.
Disable eswitch port metadata::
$ devlink dev param set pci/0000:06:00.0 name esw_port_metadata value \
false cmode runtime
Change eswitch mode to switchdev mode where after choosing the metadata value::
$ devlink dev eswitch set pci/0000:06:00.0 mode switchdev
Note that other mlx5 devlink runtime parameters, esw_multiport and
flow_steering_mode, do not have this limitation.
Signed-off-by: William Tu <witu@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since 6.8-rc1, using VTABLE_DEFAULT_ERROR for optional functions
(never called) in #[vtable] is the recommended way.
Note that no functional changes in this patch.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@gmail.com>
Reviewed-by: Trevor Gross <tmgross@umich.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
The relative paths like the following are bothersome and don't work
with `O=` builds:
//! C headers: [`include/linux/phy.h`](../../../../../../../include/linux/phy.h).
This updates such links by using the `srctree`-relative link feature
introduced in 6.8-rc1 like:
//! C headers: [`include/linux/phy.h`](srctree/include/linux/phy.h).
Signed-off-by: FUJITA Tomonori <fujita.tomonori@gmail.com>
Reviewed-by: Trevor Gross <tmgross@umich.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Correct the PHY loopback bit handling in the ksz8_w_phy_bmcr and
ksz8_r_phy_bmcr functions for KSZ8794 and KSZ8873 variants in the ksz8795
driver. Previously, the code erroneously used Bit 7 of port register 0xD
for both chip variants, which is actually for LED configuration. This
update ensures the correct registers and bits are used for the PHY
loopback feature:
- For KSZ8794: Use 0xF / Bit 7.
- For KSZ8873: Use 0xD / Bit 0.
The lack of loopback support was seen on KSZ8873 system by using
"ethtool -t lanX". After this patch, the ethtool selftest will work,
but only if port is not part of a bridge.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Link: https://lore.kernel.org/r/20240124123314.734815-4-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove the manual checks for register value changes in the
ksz8_w_phy_bmcr function. Instead, rely on regmap_update_bits() for
optimizing register updates.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Link: https://lore.kernel.org/r/20240124123314.734815-3-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Isolate the Basic Mode Control Register (BMCR) operations in the ksz8795
driver by moving the BMCR-related code segments from the ksz8_r_phy()
and ksz8_w_phy() functions to newly created ksz8_r_phy_bmcr() and
ksz8_w_phy_bmcr() functions.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Link: https://lore.kernel.org/r/20240124123314.734815-2-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQTFp0I1jqZrAX+hPRXbK58LschIgwUCZbQV+gAKCRDbK58LschI
g2OeAP0VvhZS9SPiS+/AMAFuw2W1BkMrFNbfBTc3nzRnyJSmNAD+NG4CLLJvsKI9
olu7VC20B8pLTGLUGIUSwqnjOC+Kkgc=
=wVMl
-----END PGP SIGNATURE-----
Merge tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next
Daniel Borkmann says:
====================
pull-request: bpf-next 2024-01-26
We've added 107 non-merge commits during the last 4 day(s) which contain
a total of 101 files changed, 6009 insertions(+), 1260 deletions(-).
The main changes are:
1) Add BPF token support to delegate a subset of BPF subsystem
functionality from privileged system-wide daemons such as systemd
through special mount options for userns-bound BPF fs to a trusted
& unprivileged application. With addressed changes from Christian
and Linus' reviews, from Andrii Nakryiko.
2) Support registration of struct_ops types from modules which helps
projects like fuse-bpf that seeks to implement a new struct_ops type,
from Kui-Feng Lee.
3) Add support for retrieval of cookies for perf/kprobe multi links,
from Jiri Olsa.
4) Bigger batch of prep-work for the BPF verifier to eventually support
preserving boundaries and tracking scalars on narrowing fills,
from Maxim Mikityanskiy.
5) Extend the tc BPF flavor to support arbitrary TCP SYN cookies to help
with the scenario of SYN floods, from Kuniyuki Iwashima.
6) Add code generation to inline the bpf_kptr_xchg() helper which
improves performance when stashing/popping the allocated BPF objects,
from Hou Tao.
7) Extend BPF verifier to track aligned ST stores as imprecise spilled
registers, from Yonghong Song.
8) Several fixes to BPF selftests around inline asm constraints and
unsupported VLA code generation, from Jose E. Marchesi.
9) Various updates to the BPF IETF instruction set draft document such
as the introduction of conformance groups for instructions,
from Dave Thaler.
10) Fix BPF verifier to make infinite loop detection in is_state_visited()
exact to catch some too lax spill/fill corner cases,
from Eduard Zingerman.
11) Refactor the BPF verifier pointer ALU check to allow ALU explicitly
instead of implicitly for various register types, from Hao Sun.
12) Fix the flaky tc_redirect_dtime BPF selftest due to slowness
in neighbor advertisement at setup time, from Martin KaFai Lau.
13) Change BPF selftests to skip callback tests for the case when the
JIT is disabled, from Tiezhu Yang.
14) Add a small extension to libbpf which allows to auto create
a map-in-map's inner map, from Andrey Grafin.
* tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (107 commits)
selftests/bpf: Add missing line break in test_verifier
bpf, docs: Clarify definitions of various instructions
bpf: Fix error checks against bpf_get_btf_vmlinux().
bpf: One more maintainer for libbpf and BPF selftests
selftests/bpf: Incorporate LSM policy to token-based tests
selftests/bpf: Add tests for LIBBPF_BPF_TOKEN_PATH envvar
libbpf: Support BPF token path setting through LIBBPF_BPF_TOKEN_PATH envvar
selftests/bpf: Add tests for BPF object load with implicit token
selftests/bpf: Add BPF object loading tests with explicit token passing
libbpf: Wire up BPF token support at BPF object level
libbpf: Wire up token_fd into feature probing logic
libbpf: Move feature detection code into its own file
libbpf: Further decouple feature checking logic from bpf_object
libbpf: Split feature detectors definitions from cached results
selftests/bpf: Utilize string values for delegate_xxx mount options
bpf: Support symbolic BPF FS delegation mount options
bpf: Fail BPF_TOKEN_CREATE if no delegation option was set on BPF FS
bpf,selinux: Allocate bpf_security_struct per BPF token
selftests/bpf: Add BPF token-enabled tests
libbpf: Add BPF token support to bpf_prog_load() API
...
====================
Link: https://lore.kernel.org/r/20240126215710.19855-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Christian Marangi says:
====================
net: phy: generic polarity + LED support for qca808x
This small series add LEDs support for qca808x.
QCA808x apply on PHY reset a strange polarity settings and require
some tweak to apply a more common configuration found on devices.
On adding support for it, it was pointed out that a similar
feature is also being implemented for a marvell PHY where
LED polarity is set per LED (and not global) and also have
a special mode where the LED is tristated.
The first 3 patch are to generalize this as we expect more PHY
in the future to have a similar configuration.
The implementation is extensible to support additional special
mode in the future with minimal changes and don't create regression
on already implemented PHY drivers.
====================
Link: https://lore.kernel.org/r/20240125203702.4552-1-ansuelsmth@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add LED support for QCA8081 PHY.
Documentation for this LEDs PHY is very scarce even with NDA access
to Documentation for OEMs. Only the blink pattern are documented and are
very confusing most of the time. No documentation is present about
forcing the LED on/off or to always blink.
Those settings were reversed by poking the regs and trying to find the
correct bits to trigger these modes. Some bits mode are not clear and
maybe the documentation option are not 100% correct. For the sake of LED
support the reversed option are enough to add support for current LED
APIs.
Supported HW control modes are:
- tx
- rx
- link_10
- link_100
- link_1000
- link_2500
- half_duplex
- full_duplex
Also add support for LED polarity set to set LED polarity to active
high or low. QSDK sets this value to high by default but PHY reset value
doesn't have this enabled by default.
QSDK also sets 2 additional bits but their usage is not clear, info about
this is added in the header. It was verified that for correct function
of the LED if active high is needed, only BIT 6 is needed.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240125203702.4552-6-ansuelsmth@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add Documentation for QCA808x PHYs for the additional LED configuration
for this PHY.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20240125203702.4552-5-ansuelsmth@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for PHY LEDs polarity modes. Some PHY require LED to be set
to active low to be turned ON. Adds support for this by declaring
active-low property in DT.
PHY driver needs to declare .led_polarity_set() to configure LED
polarity modes. Function will pass the index with the LED index and a
bitmap with all the required modes to set.
Current supported modes are:
- active-low with the flag PHY_LED_ACTIVE_LOW. LED is set to active-low
to turn it ON.
- inactive-high-impedance with the flag PHY_LED_INACTIVE_HIGH_IMPEDANCE.
LED is set to high impedance to turn it OFF.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240125203702.4552-4-ansuelsmth@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Document LED inactive high impedance mode to set the LED to require high
impedance configuration to be turned OFF.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Lee Jones <lee@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20240125203702.4552-3-ansuelsmth@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Move LED active-low property to common.yaml. This property is currently
defined multiple times by bcm LEDs. This property will now be supported
in a generic way for PHY LEDs with the use of a generic function.
With active-low bool property not defined, active-high is always
assumed.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Lee Jones <lee@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20240125203702.4552-2-ansuelsmth@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
