Most of the blk-ctrl reset bits are found in one register, however
there are two bits in offset 8 for pulling the MIPI DPHY out of reset
and one of them needs to be set when IMX8MM_DISPBLK_PD_MIPI_CSI is brought
out of reset or the MIPI_CSI hangs.
Since MIPI_DSI is impacted, add the additional one for MIPI_DSI too.
Fixes: 926e57c065 ("soc: imx: imx8m-blk-ctrl: add DISP blk-ctrl")
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Enable the vpu-h1 clock when the domain is active because reading
or writing to the VPU-H1 IP block cause the system to hang.
Fixes: 656ade7aa4 ("soc: imx: gpcv2: keep i.MX8M* bus clocks enabled")
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
In case the following power domain sequence happens, iMX8M Mini always hangs:
gpumix:on -> gpu:on -> gpu:off -> gpu:on
This is likely due to another quirk of the GPC block. This situation can be
prevented by always synchronously powering off both the domain and MIX domain.
Make it so. This turns the aforementioned sequence into:
gpumix:on -> gpu:on -> gpu:off -> gpumix:off -> gpumix:on -> gpu:on
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Frieder Schrempf <frieder.schrempf@kontron.de>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Acked-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The > comparison should be >= to prevent reading one element beyond the
end of the array. The onecell_data->domains[] array is allocated in
imx8m_blk_ctrl_probe() and it has "onecell_data->num_domains" elements.
Fixes: 5b340e7813d4 ("soc: imx: add i.MX8M blk-ctrl driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This adds the description for the i.MX8MM disp blk-ctrl.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This adds a driver for the blk-ctrl blocks found in the i.MX8M* line of
SoCs. The blk-ctrl is a top-level peripheral located in the various *MIX
power domains and interacts with the GPC power controller to provide the
peripherals in the power domain access to the NoC and ensures that those
peripherals are properly reset when their respective power domain is
brought back to life.
Software needs to do different things to make the bus handshake happen
after the GPC *MIX domain is powered up and before it is powered down.
As the requirements are quite different between the various blk-ctrls
there is a callback function provided to hook in the proper sequence.
The peripheral domains are quite uniform, they handle the soft clock
enables and resets in the blk-ctrl address space and sequencing with the
upstream GPC power domains.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Our usage of runtime PM to control the hierarchy of power domains is
slightly unusual and means that powering up a domain may fail in early
system resume, as runtime PM is still disallowed at this stage.
However the system suspend/resume path takes care of powering down/up
the power domains in the order defined by the device parent/child and
power-domain provider/consumer hierarachy. So we can just runtime
resume all our power-domain devices to allow the power-up to work
properly in the resume path. System suspend will still disable all
domains as intended.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Annotate the domains with bus clocks to keep those clocks enabled
as long as the domain is active.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Some of the MIX domains are using clocks to drive the bus bridges. Those
must be enabled at all times, as long as the domain is powered up and
they don't have any other consumer than the power domain. Add an option
to keep the clocks attached to a domain enabled as long as the domain
is power up and only disable them after the domain is powered down.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Some of the GPCv2 power domains are nested inside each other without
visibility to lockdep at the genpd level, as they are in separate
driver instances and don't have a parent/child power-domain relationship.
Add a subclass annotation to the nested domains to let lockdep know that
it is okay to take the genpd lock in a nested fashion.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This reverts commit a77ebdd9f553. It turns out that the VPU domain has no
different requirements, even though the downstream ATF implementation seems
to suggest otherwise. Powering on the domain with the reset asserted works
fine. As the changed sequence has caused sporadic issues with the GPU
domains, just revert the change to go back to the working sequence.
Cc: <stable@vger.kernel.org> # 5.14
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Peng Fan <peng.fan@nxp.com>
Tested-by: Adam Ford <aford173@gmail.com> #imx8mm-beacon
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Some board designs don't supply power to all of the power domains,
as they are not used anyways. In that case we must make sure to
not touch those power domains at all, as trying to power up a
domain that has no power supplied to it will obviously end in a
system crash. Allow to disable those domains via the standard DT
status property.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-By: Tim Harvey <tharvey@gateworks.com>
Tested-By: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
To bring up the MX8MM GPU domain, it is necessary to configure both
GPC_PGC_nCTRL(GPU_2D) and GPC_PGC_nCTRL(GPU_3D) registers. Without
this configuration, the system might hang on boot when bringing up
the GPU power domain. This is sporadically observed on multiple
disparate systems.
Add the GPU3D bit into MX8MM GPU domain pgc bitfield, so that both
GPC_PGC_nCTRL(GPU_2D) and GPC_PGC_nCTRL(GPU_3D) registers are
configured when bringing up the GPU domain. This fixes the sporadic
hang.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Frieder Schrempf <frieder.schrempf@kontron.de>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There is currently the MX8MM GPU domain, which is in fact a composite domain
for both GPU2D and GPU3D. To correctly configure this domain, it is necessary
to control both GPC_PGC_nCTRL(GPU_2D) and GPC_PGC_nCTRL(GPU_3D) at the same
time. This is currently not possible.
Turn the domain->pgc from value into bitfield and use for_each_set_bit() to
iterate over all bits set in domain->pgc when configuring GPC_PGC_nCTRL
register array. This way it is possible to configure all GPC_PGC_nCTRL
registers required in a particular domain.
This is a preparatory patch, no functional change.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Frieder Schrempf <frieder.schrempf@kontron.de>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
With the SoC matching changed to a platform driver the match data
is available only after other drivers, which may rely on it are
already probed. This breaks at least the CAAM driver on i.MX8M.
Revert the change until all those drivers have been audited and
changed to be able to eal with match data being available later
in the boot process.
Fixes: 7d981405d0 ("soc: imx8m: change to use platform driver")
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Acked-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
- Reset controllers: Adding support for Microchip Sparx5 Switch.
- Memory controllers: ARM Primecell PL35x SMC memory controller
driver cleanups and improvements.
- i.MX SoC drivers: Power domain support for i.MX8MM and i.MX8MN.
- Rockchip: RK3568 power domains support + DT binding updates,
cleanups.
- Qualcomm SoC drivers: Amend socinfo with more SoC/PMIC details,
including support for MSM8226, MDM9607, SM6125 and SC8180X.
- ARM FFA driver: "Firmware Framework for ARMv8-A", defining
management interfaces and communication (including bus model)
between partitions both in Normal and Secure Worlds.
- Tegra Memory controller changes, including major rework to deal
with identity mappings at boot and integration with ARM SMMU
pieces.
-----BEGIN PGP SIGNATURE-----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=kPg8
-----END PGP SIGNATURE-----
Merge tag 'arm-drivers-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM driver updates from Olof Johansson:
- Reset controllers: Adding support for Microchip Sparx5 Switch.
- Memory controllers: ARM Primecell PL35x SMC memory controller driver
cleanups and improvements.
- i.MX SoC drivers: Power domain support for i.MX8MM and i.MX8MN.
- Rockchip: RK3568 power domains support + DT binding updates,
cleanups.
- Qualcomm SoC drivers: Amend socinfo with more SoC/PMIC details,
including support for MSM8226, MDM9607, SM6125 and SC8180X.
- ARM FFA driver: "Firmware Framework for ARMv8-A", defining management
interfaces and communication (including bus model) between partitions
both in Normal and Secure Worlds.
- Tegra Memory controller changes, including major rework to deal with
identity mappings at boot and integration with ARM SMMU pieces.
* tag 'arm-drivers-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (120 commits)
firmware: turris-mox-rwtm: add marvell,armada-3700-rwtm-firmware compatible string
firmware: turris-mox-rwtm: show message about HWRNG registration
firmware: turris-mox-rwtm: fail probing when firmware does not support hwrng
firmware: turris-mox-rwtm: report failures better
firmware: turris-mox-rwtm: fix reply status decoding function
soc: imx: gpcv2: add support for i.MX8MN power domains
dt-bindings: add defines for i.MX8MN power domains
firmware: tegra: bpmp: Fix Tegra234-only builds
iommu/arm-smmu: Use Tegra implementation on Tegra186
iommu/arm-smmu: tegra: Implement SID override programming
iommu/arm-smmu: tegra: Detect number of instances at runtime
dt-bindings: arm-smmu: Add Tegra186 compatible string
firmware: qcom_scm: Add MDM9607 compatible
soc: qcom: rpmpd: Add MDM9607 RPM Power Domains
soc: renesas: Add support to read LSI DEVID register of RZ/G2{L,LC} SoC's
soc: renesas: Add ARCH_R9A07G044 for the new RZ/G2L SoC's
dt-bindings: soc: rockchip: drop unnecessary #phy-cells from grf.yaml
memory: emif: remove unused frequency and voltage notifiers
memory: fsl_ifc: fix leak of private memory on probe failure
memory: fsl_ifc: fix leak of IO mapping on probe failure
...
This adds support for the power domains founds on i.MX8MN. The Nano
has fewer domains than the Mini, and the access to some of these domains
is different than that of the Mini, the Mini power domains cannot be
reused.
Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The i.MX8MM VPU power up sequence is a bit special, it must follow:
1. request power up
2. reset assert
3. reset deassert
This change in this patch will not affect other domains, because
the power domain default is in asserted state, unless bootloader
deassert the reset. It also applies to GPU power domain.
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
With the BLK-CTL driver now in place, let's add the missing domains.
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This adds support for the power domains found on i.MX8MM. The 2D and 3D
GPU domains are abstracted as a single domain in the driver, as they can't
be powered up/down individually due to a shared reset.
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Normally the reset for the devices inside the power domain is
triggered automatically from the PGC in the power-up sequencing,
however on i.MX8MM this doesn't work for the GPU power domains.
Add support for triggering the reset explicitly during the power
up sequencing.
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Some of the PGC domains only control the handshake with the ADB400
and don't have any power sequence controls. Make such domains work
by allowing the pxx and map bits to be empty and skip all actions
using those controls.
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This allows to nest domains into other power domains and have the
parent domain powered up/down as required by the child domains.
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
New reference manuals show that there is actually a status bit for
the ADB400 handshake. Add a poll loop to wait for the ADB400 to
acknowledge our request.
[Peng Fan: i.MX8MM has blk ctl module, the handshake can only finish
after setting blk ctl. The blk ctl driver will set the bus clk bit and
the handshake will finish there. we just add a delay and suppose the
handshake will finish after that.]
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The current mixed function to control both power up and power down
sequences is very hard to follow and already contains some sequence
errors like triggering the ADB400 handshake at the wrong time due to
this. Split the function into two, which results in slightly more
code, but is way easier to get right.
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Use clk_bulk API to simplify the code a bit. Also add some error
checking to the clk_prepare_enable calls.
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
As long as the power domain driver is active we want power control
over the domain (which is what the mapping bit requests), so there
is no point in whacking it for every power control action, simply
set the bit in driver probe and clear it when the driver is removed.
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Switch to "goto out..." error handling in domain driver probe to
avoid repeating all the error paths.
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Tested-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
As on i.MX51 and i.MX53, initialize the SoC ID based on the SoC
compatible string of the board.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX51 and i.MX53 SoCs have a 64-bit SoC unique ID stored in IIM,
which can be used as SoC serial number. The same feature is already
implemented for i.MX6/i.MX7, so this complements support to earlier
SoCs.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Updates for SoC specific drivers include a few subsystems that
have their own maintainers but send them through the soc tree:
SCMI firmware:
- add support for a completion interrupt
Reset controllers:
- new driver for BCM4908
- new devm_reset_control_get_optional_exclusive_released()
function
Memory controllers:
- Renesas RZ/G2 support
- Tegra124 interconnect support
- Allow more drivers to be loadable modules
TEE/optee firmware:
- minor code cleanup
The other half of this is SoC specific drivers that do not
belong into any other subsystem, most of them living in
drivers/soc:
- Allwinner/sunxi power management work
- Allwinner H616 support
- ASpeed AST2600 system identification support
- AT91 SAMA7G5 SoC ID driver
- AT91 SoC driver cleanups
- Broadcom BCM4908 power management bus support
- Marvell mbus cleanups
- Mediatek MT8167 power domain support
- Qualcomm socinfo driver support for PMIC
- Qualcomm SoC identification for many more products
- TI Keystone driver cleanups for PRUSS and elsewhere
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=I2Zn
-----END PGP SIGNATURE-----
Merge tag 'arm-drivers-v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"Updates for SoC specific drivers include a few subsystems that have
their own maintainers but send them through the soc tree:
SCMI firmware:
- add support for a completion interrupt
Reset controllers:
- new driver for BCM4908
- new devm_reset_control_get_optional_exclusive_released() function
Memory controllers:
- Renesas RZ/G2 support
- Tegra124 interconnect support
- Allow more drivers to be loadable modules
TEE/optee firmware:
- minor code cleanup
The other half of this is SoC specific drivers that do not belong into
any other subsystem, most of them living in drivers/soc:
- Allwinner/sunxi power management work
- Allwinner H616 support
- ASpeed AST2600 system identification support
- AT91 SAMA7G5 SoC ID driver
- AT91 SoC driver cleanups
- Broadcom BCM4908 power management bus support
- Marvell mbus cleanups
- Mediatek MT8167 power domain support
- Qualcomm socinfo driver support for PMIC
- Qualcomm SoC identification for many more products
- TI Keystone driver cleanups for PRUSS and elsewhere"
* tag 'arm-drivers-v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (89 commits)
soc: aspeed: socinfo: Add new systems
soc: aspeed: snoop: Add clock control logic
memory: tegra186-emc: Replace DEFINE_SIMPLE_ATTRIBUTE with DEFINE_DEBUGFS_ATTRIBUTE
memory: samsung: exynos5422-dmc: Correct function names in kerneldoc
memory: ti-emif-pm: Drop of_match_ptr from of_device_id table
optee: simplify i2c access
drivers: soc: atmel: fix type for same7
tee: optee: remove need_resched() before cond_resched()
soc: qcom: ocmem: don't return NULL in of_get_ocmem
optee: sync OP-TEE headers
tee: optee: fix 'physical' typos
drivers: optee: use flexible-array member instead of zero-length array
tee: fix some comment typos in header files
soc: ti: k3-ringacc: Use of_device_get_match_data()
soc: ti: pruss: Refactor the CFG sub-module init
soc: mediatek: pm-domains: Don't print an error if child domain is deferred
soc: mediatek: pm-domains: Add domain regulator supply
dt-bindings: power: Add domain regulator supply
soc: mediatek: cmdq: Remove cmdq_pkt_flush()
soc: mediatek: pm-domains: Add support for mt8167
...
Directly reading ocotp register depends on that bootloader enables ocotp
clk, which is not always effective, so change to use nvmem API. Using
nvmem API requires to support driver defer probe and thus change
soc-imx8m.c to use platform driver.
The other reason is that directly reading ocotp register causes kexec
kernel hang because the 1st kernel running will disable unused clks
after kernel boots up, and then ocotp clk will be disabled even if
bootloader enables it. When kexec kernel, ocotp clk needs to be enabled
before reading ocotp registers, and nvmem API with platform driver
supported can accomplish this.
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Selecting ARM_GIC_V3 on non-CP15 processors leads to build failures
like
arch/arm/include/asm/arch_gicv3.h: In function 'write_ICC_AP1R3_EL1':
arch/arm/include/asm/arch_gicv3.h:36:40: error: 'c12' undeclared (first use in this function)
36 | #define __ICC_AP1Rx(x) __ACCESS_CP15(c12, 0, c9, x)
| ^~~
Add a dependency to only enable the gic driver when building for
at an ARMv7 target, which is the closes approximation to the ARMv8
processor that is actually in this chip.
Fixes: fc40200ebf ("soc: imx: increase build coverage for imx8m soc driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
dev_err_probe() can reduce code size, uniform error handling and record the
defer probe reason etc., use it to simplify the code.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
A couple of subsystems have their own subsystem maintainers but choose
to have the code merged through the soc tree as upstream, as the code
tends to be used across multiple SoCs or has SoC specific drivers itself:
- memory controllers:
Krzysztof Kozlowski takes ownership of the drivers/memory
subsystem and its drivers, starting out with a set of cleanup
patches.
A larger driver for the Tegra memory controller that was accidentally
missed for v5.8 is now added.
- reset controllers:
Only minor updates to drivers/reset this time
- firmware:
The "turris mox" firmware driver gains support for signed firmware blobs
The tegra firmware driver gets extended to export some debug information
Various updates to i.MX firmware drivers, mostly cosmetic
- ARM SCMI/SCPI:
A new mechanism for platform notifications is added, among a number
of minor changes.
- optee:
Probing of the TEE bus is rewritten to better support detection of
devices that depend on the tee-supplicant user space.
A new firmware based trusted platform module (fTPM) driver is added
based on OP-TEE
- SoC attributes:
A new driver is added to provide a generic soc_device for identifying
a machine through the SMCCC ARCH_SOC_ID firmware interface rather than
by probing SoC family specific registers.
The series also contains some cleanups to the common soc_device code.
There are also a number of updates to SoC specific drivers,
the main ones are:
- Mediatek cmdq driver gains a few in-kernel interfaces
- Minor updates to Qualcomm RPMh, socinfo, rpm drivers, mostly adding
support for additional SoC variants
- The Qualcomm GENI core code gains interconnect path voting and
performance level support, and integrating this into a number of
device drivers.
- A new driver for Samsung Exynos5800 voltage coupler for
- Renesas RZ/G2H (R8A774E1) SoC support gets added to a couple of SoC
specific device drivers
- Updates to the TI K3 Ring Accelerator driver
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEo6/YBQwIrVS28WGKmmx57+YAGNkFAl8j3y4ACgkQmmx57+YA
GNm8Iw//euEC37KaiBDhlK3mcAL7NOdITqZpq4m+ZJZBsF02NDMWktJR8bYuOgmp
kjR4LjCxa2i+UOq1Ln+zYSlS27AngZLHFM+YSG3jqDho12GYIe4OBZB/q/hkDu71
L5jCPNrZV9+GIcean2u8LOWDNlQ4SZQyZ1/gcCK7y7I8W1pVulmJRhtJ0MNkezni
gDQ+OH+6+6XY8AethWK9ubsYH7SeJX/U6I8t5KJGhPr6FlaJFZOO5RTdUkBFMHpS
i4UaT4meuqZUjwz4BhjvoYul5AT6Zc8OOTQwk1FM7dIe47aI8VkWrWci/IekxoLh
UXtKbAJxerCIdehfiygX4pKtOmRKSisS2ocWsKg46Htu11ltv0XMRgyLyGv4Vm84
g+fKfKUL0SUueDqr+jKEq2aZdyLxwV5ZUoFt3IVsXdHRkZtxpN8jmOHOjV6erLVY
m7S85U5eclNdK5Ap7RSVvQa4NP3NTUvJd1IDNIneUVyACRkxzWEKmE3ZuEO4qttS
WSDW74m5ja80pltv1umFbGAsOUTZWA+WGULeXPv4CIooaD8RL6Jzs+7tkZEEhleU
WlGBFE4eJi/ChMeyTKXPvEqsQncLSf0mGzM4/DVY6XRSTIrW+cuj1/Gsso1BJdod
aZZ76uMNHJdAt0PcxL47lDUDxhJDkTwBsfGNJseZ3sYlAQ7Wmqo=
=nezz
-----END PGP SIGNATURE-----
Merge tag 'arm-drivers-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"A couple of subsystems have their own subsystem maintainers but choose
to have the code merged through the soc tree as upstream, as the code
tends to be used across multiple SoCs or has SoC specific drivers
itself:
- memory controllers:
Krzysztof Kozlowski takes ownership of the drivers/memory subsystem
and its drivers, starting out with a set of cleanup patches.
A larger driver for the Tegra memory controller that was
accidentally missed for v5.8 is now added.
- reset controllers:
Only minor updates to drivers/reset this time
- firmware:
The "turris mox" firmware driver gains support for signed firmware
blobs The tegra firmware driver gets extended to export some debug
information Various updates to i.MX firmware drivers, mostly
cosmetic
- ARM SCMI/SCPI:
A new mechanism for platform notifications is added, among a number
of minor changes.
- optee:
Probing of the TEE bus is rewritten to better support detection of
devices that depend on the tee-supplicant user space. A new
firmware based trusted platform module (fTPM) driver is added based
on OP-TEE
- SoC attributes:
A new driver is added to provide a generic soc_device for
identifying a machine through the SMCCC ARCH_SOC_ID firmware
interface rather than by probing SoC family specific registers.
The series also contains some cleanups to the common soc_device
code.
There are also a number of updates to SoC specific drivers, the main
ones are:
- Mediatek cmdq driver gains a few in-kernel interfaces
- Minor updates to Qualcomm RPMh, socinfo, rpm drivers, mostly adding
support for additional SoC variants
- The Qualcomm GENI core code gains interconnect path voting and
performance level support, and integrating this into a number of
device drivers.
- A new driver for Samsung Exynos5800 voltage coupler for
- Renesas RZ/G2H (R8A774E1) SoC support gets added to a couple of SoC
specific device drivers
- Updates to the TI K3 Ring Accelerator driver"
* tag 'arm-drivers-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (164 commits)
soc: qcom: geni: Fix unused label warning
soc: qcom: smd-rpm: Fix kerneldoc
memory: jz4780_nemc: Only request IO memory the driver will use
soc: qcom: pdr: Reorder the PD state indication ack
MAINTAINERS: Add Git repository for memory controller drivers
memory: brcmstb_dpfe: Fix language typo
memory: samsung: exynos5422-dmc: Correct white space issues
memory: samsung: exynos-srom: Correct alignment
memory: pl172: Enclose macro argument usage in parenthesis
memory: of: Correct kerneldoc
memory: omap-gpmc: Fix language typo
memory: omap-gpmc: Correct white space issues
memory: omap-gpmc: Use 'unsigned int' for consistency
memory: omap-gpmc: Enclose macro argument usage in parenthesis
memory: omap-gpmc: Correct kerneldoc
memory: mvebu-devbus: Align with open parenthesis
memory: mvebu-devbus: Add missing braces to all arms of if statement
memory: bt1-l2-ctl: Add blank lines after declarations
soc: TI knav_qmss: make symbol 'knav_acc_range_ops' static
firmware: ti_sci: Replace HTTP links with HTTPS ones
...
Select ARM_GIC_V3, then it is able to use gic v3 driver in aarch32
mode linux on aarch64 hardware. For aarch64 mode, it not hurts
to select ARM_GIC_V3.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
fsl,ls1021a is a mach under arch/arm/mach-imx/, however it could
not use the soc driver which will break caam on ls1021a platform.
So directly return if it is compatible with fsl,ls1021a.
Fixes: 52102a3ba6 ("soc: imx: move cpu code to drivers/soc/imx")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Tested-by: Horia Geantă <horia.geanta@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The i.MX SCU soc driver depends on SCU firmware driver, so it has to
use platform driver model for proper defer probe operation, since
it has no device binding in DT file, a simple platform device is
created together inside the platform driver. To make it more clean,
we can just move the entire SCU soc driver into imx firmware folder
and initialized by i.MX SCU firmware driver.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
These are updates to SoC specific drivers that did not have
another subsystem maintainer tree to go through for some
reason:
- Some bus and memory drivers for the MIPS P5600 based
Baikal-T1 SoC that is getting added through the MIPS tree.
- There are new soc_device identification drivers for TI K3,
Qualcomm MSM8939
- New reset controller drivers for NXP i.MX8MP, Renesas
RZ/G1H, and Hisilicon hi6220
- The SCMI firmware interface can now work across ARM SMC/HVC
as a transport.
- Mediatek platforms now use a new driver for their "MMSYS"
hardware block that controls clocks and some other aspects
in behalf of the media and gpu drivers.
- Some Tegra processors have improved power management
support, including getting woken up by the PMIC and cluster
power down during idle.
- A new v4l staging driver for Tegra is added.
- Cleanups and minor bugfixes for TI, NXP, Hisilicon,
Mediatek, and Tegra.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=44Jc
-----END PGP SIGNATURE-----
Merge tag 'arm-drivers-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM/SoC driver updates from Arnd Bergmann:
"These are updates to SoC specific drivers that did not have another
subsystem maintainer tree to go through for some reason:
- Some bus and memory drivers for the MIPS P5600 based Baikal-T1 SoC
that is getting added through the MIPS tree.
- There are new soc_device identification drivers for TI K3, Qualcomm
MSM8939
- New reset controller drivers for NXP i.MX8MP, Renesas RZ/G1H, and
Hisilicon hi6220
- The SCMI firmware interface can now work across ARM SMC/HVC as a
transport.
- Mediatek platforms now use a new driver for their "MMSYS" hardware
block that controls clocks and some other aspects in behalf of the
media and gpu drivers.
- Some Tegra processors have improved power management support,
including getting woken up by the PMIC and cluster power down
during idle.
- A new v4l staging driver for Tegra is added.
- Cleanups and minor bugfixes for TI, NXP, Hisilicon, Mediatek, and
Tegra"
* tag 'arm-drivers-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (155 commits)
clk: sprd: fix compile-testing
bus: bt1-axi: Build the driver into the kernel
bus: bt1-apb: Build the driver into the kernel
bus: bt1-axi: Use sysfs_streq instead of strncmp
bus: bt1-axi: Optimize the return points in the driver
bus: bt1-apb: Use sysfs_streq instead of strncmp
bus: bt1-apb: Use PTR_ERR_OR_ZERO to return from request-regs method
bus: bt1-apb: Fix show/store callback identations
bus: bt1-apb: Include linux/io.h
dt-bindings: memory: Add Baikal-T1 L2-cache Control Block binding
memory: Add Baikal-T1 L2-cache Control Block driver
bus: Add Baikal-T1 APB-bus driver
bus: Add Baikal-T1 AXI-bus driver
dt-bindings: bus: Add Baikal-T1 APB-bus binding
dt-bindings: bus: Add Baikal-T1 AXI-bus binding
staging: tegra-video: fix V4L2 dependency
tee: fix crypto select
drivers: soc: ti: knav_qmss_queue: Make knav_gp_range_ops static
soc: ti: add k3 platforms chipid module driver
dt-bindings: soc: ti: add binding for k3 platforms chipid module
...
- Add soc device support for Vybrid/VF platform.
- Move the i.MX soc device registration code from mach-imx to
drivers/soc/imx for possible future consolidation with i.MX8 code.
- A small fixup to make pcm970_sja1000_platform_data static.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCgAyFiEEFmJXigPl4LoGSz08UFdYWoewfM4FAl7IflgUHHNoYXduZ3Vv
QGtlcm5lbC5vcmcACgkQUFdYWoewfM5Tswf+Id6DM109IHuZxhPWNB5SKEkVa1cr
v7u7GeT/REqnsVCoFgC0kYIVlOj6nm7F8wwrHziiocvryUV8KPiENG3zMCVzJfLz
+xkZxIYEuMeLoJjWOz3HeR5bp8G5GeL8sGt2D5OrMh1EUHYTZdnf4/nESvCMJb41
rOaBRHuhhR1/Dv8qwCkXU9zep/jwlVXf+r6pC5pQNGmUpUGC2VFc7rDYkODS8Jo4
MfNx5S+HHk2Jabei+6fKEsVG1x7E3lv3ky/ZdVWhjtgy19I32E+o4Cr+UQqegIen
N4V/Uya6KejSvhaHDf6Pz2TjqTkXxlWSQ0Lu2I7pDMWdU5Upf0iLqbV1rQ==
=MC2F
-----END PGP SIGNATURE-----
Merge tag 'imx-soc-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/soc
i.MX SoC changes for 5.8:
- Add soc device support for Vybrid/VF platform.
- Move the i.MX soc device registration code from mach-imx to
drivers/soc/imx for possible future consolidation with i.MX8 code.
- A small fixup to make pcm970_sja1000_platform_data static.
* tag 'imx-soc-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
soc: imx: move cpu code to drivers/soc/imx
ARM: imx: move cpu definitions into a header
ARM: imx: use device_initcall for imx_soc_device_init
ARM: imx: pcm037: make pcm970_sja1000_platform_data static
ARM: vf610: report soc info via soc device
Link: https://lore.kernel.org/r/20200523032516.11016-2-shawnguo@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Optimize imx-scu driver to use one TX and one RX instead of four for
talking to SCU.
- Fix one possible message header corruption where the response is
longer than the request.
- Move System Control defines into dt-bindings header, so that DT can
use them as well.
- A couple of small fixups.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCgAyFiEEFmJXigPl4LoGSz08UFdYWoewfM4FAl7IeuUUHHNoYXduZ3Vv
QGtlcm5lbC5vcmcACgkQUFdYWoewfM5CpAf/VV2krqXlgTXA1Ppl+ivdGkx9ntwo
dVtZYNr65Z1iqp6yujW7cH/qulXfkaFanwDptq9ulBkG6uiyV06GCtBxpp3VhNOB
60uaS8RsieYmCz3e8j4kZkMCBthpD72wt0DxF1TlJu2d/cWfsM4/bMbrx0qYiT0V
J5FqcGH0xbe+E5YITdoPQbNxEig49q2P6BhkNLQelVQtVgM0lwSpDX3WRpCizch4
bbKSVYudV/rGGPM7ZYM53N+ngwKZurRbIf7br1QgA4ZlQxdCtADB6IRd2RsfrC8P
4BizRONfh46ogrnb9/P951RZu9H7VFRkTurnXdU+NcFK8HPYDGQmm7P2SQ==
=cJwM
-----END PGP SIGNATURE-----
Merge tag 'imx-drivers-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/drivers
i.MX drivers update for 5.8:
- Optimize imx-scu driver to use one TX and one RX instead of four for
talking to SCU.
- Fix one possible message header corruption where the response is
longer than the request.
- Move System Control defines into dt-bindings header, so that DT can
use them as well.
- A couple of small fixups.
* tag 'imx-drivers-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
firmware: imx: scu: Fix possible memory leak in imx_scu_probe()
dt-bindings: firmware: imx: Add more system controls and PM clock types
dt-bindings: firmware: imx: Move system control into dt-binding headfile
firmware: imx: scu: Fix corruption of header
firmware: imx-scu: Support one TX and one RX
soc: imx8m: No need to put node when of_find_compatible_node() failed
Link: https://lore.kernel.org/r/20200523032516.11016-1-shawnguo@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Move the soc device register code to drivers/soc/imx to align with
i.MX8.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Compile-testing the driver can result in a link failure
when CONFIG_SOC_BUS is disabled:
x86_64-linux-ld: drivers/soc/imx/soc-imx8m.o: in function `imx8_soc_init':
soc-imx8m.c:(.init.text+0x28d): undefined reference to `soc_device_register'
Select it from Kconfig, as we do from the other SoC drivers.
Link: https://lore.kernel.org/r/20200409075208.2824062-1-arnd@arndb.de
Fixes: fc40200ebf ("soc: imx: increase build coverage for imx8m soc driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
No need to put node when of_find_compatible_node() failed, return
immediately to simplify the code.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
These are the usual updates for SoC specific device drivers and related
subsystems that don't have their own top-level maintainers:
- ARM SCMI/SCPI updates to allow pluggable transport layers
- TEE subsystem cleanups
- A new driver for the Amlogic secure power domain controller
- Various driver updates for the NXP Layerscape DPAA2, NXP i.MX SCU and
TI OMAP2+ sysc drivers.
- Qualcomm SoC driver updates, including a new library module for
"protection domain" notifications
- Lots of smaller bugfixes and cleanups in other drivers
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=qbsP
-----END PGP SIGNATURE-----
Merge tag 'arm-drivers-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM driver updates from Arnd Bergmann:
"These are the usual updates for SoC specific device drivers and
related subsystems that don't have their own top-level maintainers:
- ARM SCMI/SCPI updates to allow pluggable transport layers
- TEE subsystem cleanups
- A new driver for the Amlogic secure power domain controller
- Various driver updates for the NXP Layerscape DPAA2, NXP i.MX SCU
and TI OMAP2+ sysc drivers.
- Qualcomm SoC driver updates, including a new library module for
"protection domain" notifications
- Lots of smaller bugfixes and cleanups in other drivers"
* tag 'arm-drivers-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (70 commits)
soc: fsl: qe: fix sparse warnings for ucc_slow.c
soc: fsl: qe: ucc_slow: remove 0 assignment for kzalloc'ed structure
soc: fsl: qe: fix sparse warnings for ucc_fast.c
soc: fsl: qe: fix sparse warnings for qe_ic.c
soc: fsl: qe: fix sparse warnings for ucc.c
soc: fsl: qe: fix sparse warning for qe_common.c
soc: fsl: qe: fix sparse warnings for qe.c
soc: qcom: Fix QCOM_APR dependencies
soc: qcom: pdr: Avoid uninitialized use of found in pdr_indication_cb
soc: imx: drop COMPILE_TEST for IMX_SCU_SOC
firmware: imx: add COMPILE_TEST for IMX_SCU driver
soc: imx: gpc: fix power up sequencing
soc: imx: increase build coverage for imx8m soc driver
soc: qcom: apr: Add avs/audio tracking functionality
dt-bindings: soc: qcom: apr: Add protection domain bindings
soc: qcom: Introduce Protection Domain Restart helpers
devicetree: bindings: firmware: add ipq806x to qcom_scm
memory: tegra: Correct debugfs clk rate-range on Tegra124
memory: tegra: Correct debugfs clk rate-range on Tegra30
memory: tegra: Correct debugfs clk rate-range on Tegra20
...
With COMPILE_TEST, there will be build error, because IMX_SCU
might be set to n, so drop COMPILE_TEST.
Suggested-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Currently we wait only until the PGC inverts the isolation setting
before disabling the peripheral clocks. This doesn't ensure that the
reset is properly propagated through the peripheral devices in the
power domain.
Wait until the PGC signals that the power up request is done and
wait a bit for resets to propagate before disabling the clocks.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The soc-imx8.c driver is actually for i.MX8M family, so rename it
to soc-imx8m.c.
Use CONFIG_SOC_IMX8M as build gate, not CONFIG_ARCH_MXC, to control
whether build this driver, also make it possible for compile test.
Default set it to y for ARCH_MXC && ARM64
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The imx SC api strongly assumes that messages are composed out of
4-bytes words but some of our message structs have odd sizeofs.
This produces many oopses with CONFIG_KASAN=y.
Fix by marking with __aligned(4).
Fixes: 73feb4d0f8 ("soc: imx-scu: Add SoC UID(unique identifier) support")
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This header is included indirectly on arm/arm64 but not on x86 so
CONFIG_COMPILE_TEST breaks. Fix by including <linux/sizes.h> directly.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
IMX_SCU_SOC can be compile tested to increase build coverage.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This is useful information to have when looking through system logs,
so add it to the output.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Various driver updates for platforms:
- A larger set of work on Tegra 2/3 around memory controller and
regulator features, some fuse cleanups, etc..
- MMP platform drivers, in particular for USB PHY, and other smaller
additions.
- Samsung Exynos 5422 driver for DMC (dynamic memory configuration),
and ASV (adaptive voltage), allowing the platform to run at more
optimal operating points.
- Misc refactorings and support for RZ/G2N and R8A774B1 from Renesas
- Clock/reset control driver for TI/OMAP
- Meson-A1 reset controller support
- Qualcomm sdm845 and sda845 SoC IDs for socinfo
-----BEGIN PGP SIGNATURE-----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=dk7w
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Olof Johansson:
"Various driver updates for platforms:
- A larger set of work on Tegra 2/3 around memory controller and
regulator features, some fuse cleanups, etc..
- MMP platform drivers, in particular for USB PHY, and other smaller
additions.
- Samsung Exynos 5422 driver for DMC (dynamic memory configuration),
and ASV (adaptive voltage), allowing the platform to run at more
optimal operating points.
- Misc refactorings and support for RZ/G2N and R8A774B1 from Renesas
- Clock/reset control driver for TI/OMAP
- Meson-A1 reset controller support
- Qualcomm sdm845 and sda845 SoC IDs for socinfo"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (150 commits)
firmware: arm_scmi: Fix doorbell ring logic for !CONFIG_64BIT
soc: fsl: add RCPM driver
dt-bindings: fsl: rcpm: Add 'little-endian' and update Chassis definition
memory: tegra: Consolidate registers definition into common header
memory: tegra: Ensure timing control debug features are disabled
memory: tegra: Introduce Tegra30 EMC driver
memory: tegra: Do not handle error from wait_for_completion_timeout()
memory: tegra: Increase handshake timeout on Tegra20
memory: tegra: Print a brief info message about EMC timings
memory: tegra: Pre-configure debug register on Tegra20
memory: tegra: Include io.h instead of iopoll.h
memory: tegra: Adapt for Tegra20 clock driver changes
memory: tegra: Don't set EMC rate to maximum on probe for Tegra20
memory: tegra: Add gr2d and gr3d to DRM IOMMU group
memory: tegra: Set DMA mask based on supported address bits
soc: at91: Add Atmel SFR SN (Serial Number) support
memory: atmel-ebi: switch to SPDX license identifiers
memory: atmel-ebi: move NUM_CS definition inside EBI driver
soc: mediatek: Refactor bus protection control
soc: mediatek: Refactor sram control
...
SOC revision on older imx8mq is not available in fuses so on anything
other than B1 current code just reports "unknown".
TF-A already handles this by parsing the ROM and exposes the value
through a SMC call. Call this instead of reimplementing the workaround
in the kernel itself.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The soc_device_attribute structure already contains a serial_number
attribute to show SoC's unique ID, just use it to show SoC's unique
ID instead of creating a new file called soc_uid.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The soc_device_attribute structure already contains a serial_number
attribute to show SoC's unique ID, just use it to show SoC's unique
ID instead of creating a new file called soc_uid.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Make the initialiers in imx_gpc_domains C99 format to fix the
following sparse warnings:
drivers/soc/imx/gpc.c:252:30: warning: obsolete array initializer, use C99 syntax
drivers/soc/imx/gpc.c:258:29: warning: obsolete array initializer, use C99 syntax
drivers/soc/imx/gpc.c:269:34: warning: obsolete array initializer, use C99 syntax
drivers/soc/imx/gpc.c:278:30: warning: obsolete array initializer, use C99 syntax
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Fixes: b0682d485f ("soc: imx: gpc: use GPC_PGC_DOMAIN_* indexes")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The SCU firmware API for getting UID should have response,
otherwise, the message stored in function stack could be
released and then the response data received from SCU will be
stored into that released stack and cause kernel NULL pointer
dump.
Fixes: 73feb4d0f8 ("soc: imx-scu: Add SoC UID(unique identifier) support")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The current code prints 'ret' (thus 0) while it should use 'err'.
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Various driver updates for platforms and a couple of the small driver
subsystems we merge through our tree:
- A driver for SCU (system control) on NXP i.MX8QXP
- Qualcomm Always-on Subsystem messaging driver (AOSS QMP)
- Qualcomm PM support for MSM8998
- Support for a newer version of DRAM PHY driver for Broadcom (DPFE)
- Reset controller support for Bitmain BM1880
- TI SCI (System Control Interface) support for CPU control on AM654
processors
- More TI sysc refactoring and rework
-----BEGIN PGP SIGNATURE-----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=ek+j
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC-related driver updates from Olof Johansson:
"Various driver updates for platforms and a couple of the small driver
subsystems we merge through our tree:
- A driver for SCU (system control) on NXP i.MX8QXP
- Qualcomm Always-on Subsystem messaging driver (AOSS QMP)
- Qualcomm PM support for MSM8998
- Support for a newer version of DRAM PHY driver for Broadcom (DPFE)
- Reset controller support for Bitmain BM1880
- TI SCI (System Control Interface) support for CPU control on AM654
processors
- More TI sysc refactoring and rework"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (84 commits)
reset: remove redundant null check on pointer dev
soc: rockchip: work around clang warning
dt-bindings: reset: imx7: Fix the spelling of 'indices'
soc: imx: Add i.MX8MN SoC driver support
soc: aspeed: lpc-ctrl: Fix probe error handling
soc: qcom: geni: Add support for ACPI
firmware: ti_sci: Fix gcc unused-but-set-variable warning
firmware: ti_sci: Use the correct style for SPDX License Identifier
soc: imx8: Use existing of_root directly
soc: imx8: Fix potential kernel dump in error path
firmware/psci: psci_checker: Park kthreads before stopping them
memory: move jedec_ddr.h from include/memory to drivers/memory/
memory: move jedec_ddr_data.c from lib/ to drivers/memory/
MAINTAINERS: Remove myself as qcom maintainer
soc: aspeed: lpc-ctrl: make parameter optional
soc: qcom: apr: Don't use reg for domain id
soc: qcom: fix QCOM_AOSS_QMP dependency and build errors
memory: tegra: Fix -Wunused-const-variable
firmware: tegra: Early resume BPMP
soc/tegra: Select pinctrl for Tegra194
...
Pull ARM cpufreq changes for v5.3 from Viresh Kumar:
"This pull request contains:
- Minor fixes for brcmstb driver (Florian).
- New imx-cpufreq driver, its bindings and code around it (Leonard).
- New Raspberry Pi driver (Nicolas).
- Minor fix for s5pv210 driver (Pawel).
- Minor cleanup for armada driver (YueHaibing)."
* 'cpufreq/arm/linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm:
cpufreq: s5pv210: Don't flood kernel log after cpufreq change
cpufreq: add driver for Raspberry Pi
cpufreq: Switch imx7d to imx-cpufreq-dt for speed grading
cpufreq: imx-cpufreq-dt: Remove global platform match list
cpufreq: brcmstb-avs-cpufreq: Fix types for voltage/frequency
cpufreq: brcmstb-avs-cpufreq: Fix initial command check
cpufreq: armada-37xx: Remove set but not used variable 'freq'
cpufreq: imx-cpufreq-dt: Fix no OPPs available on unfused parts
dt-bindings: imx-cpufreq-dt: Document opp-supported-hw usage
cpufreq: Add imx-cpufreq-dt driver
- Add i.MX SCU based SoC bus driver for i.MX8QXP SoC support, which
talks to SCU firmware for getting SoC ID and revision.
- Update soc-imx8 bus driver to read imx8mm soc revision from anatop.
- Add i.MX8MN SoC bus support into soc-imx8 driver.
- Various small improvements on soc-imx8 bus driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJdEX9EAAoJEFBXWFqHsHzOixgIAJ5FXbnVlJdoFkfFTOqQpzM5
w0/dPoJLyZOPd42SU4zTAlj7ooPCN+ux+AvOpf4BOMMZjJ3SnKRccpA7yPrhAAyb
pjYEGJAB1bLX1B4bnGJy2lHZzZFkGEMo2rK6jUl7agLV0T5HnV0/bRtBePCei8as
AXO5VhsXqxczG0EwqkwxdLWrvlFNwTtxi9XY90h/Af/tLUwRS4/V0/btE17r/v+2
FgoCZkHiGt+zfTzDdBSc+sV1MMcSgIGHDVTIRD1x2BfMC3VBng1HZy8aVZL2f5YP
FvDeP4W91bGSlfztKxZtZI7LLQ5oAJujgJFOvtqaaRQxV8Fk7DsNeSN58c9nRf4=
=qYcp
-----END PGP SIGNATURE-----
Merge tag 'imx-drivers-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/drivers
i.MX driver changes for 5.3:
- Add i.MX SCU based SoC bus driver for i.MX8QXP SoC support, which
talks to SCU firmware for getting SoC ID and revision.
- Update soc-imx8 bus driver to read imx8mm soc revision from anatop.
- Add i.MX8MN SoC bus support into soc-imx8 driver.
- Various small improvements on soc-imx8 bus driver.
* tag 'imx-drivers-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
soc: imx: Add i.MX8MN SoC driver support
soc: imx8: Use existing of_root directly
soc: imx8: Fix potential kernel dump in error path
soc: imx: soc-imx8: Correct return value of error handle
soc: imx: soc-imx8: Avoid unnecessary of_node_put() in error handling
soc: imx: Add SCU SoC info driver support
soc: imx: Read imx8mm soc revision from anatop
Signed-off-by: Olof Johansson <olof@lixom.net>
There is common of_root for reference, no need to find it
from DT again, use of_root directly to make driver simple.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Current implementation of i.MX8 SoC driver returns -ENODEV
for all cases of error during initialization, this is incorrect.
This patch fixes them using correct return value according
to different errors.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
of_node_put() is called after of_match_node() successfully called,
then in the following error handling, of_node_put() is called again
which is unnecessary, this patch adjusts the location of of_node_put()
to avoid such scenario.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add i.MX SCU SoC info driver to support i.MX8QXP SoC, introduce
driver dependency into Kconfig as CONFIG_IMX_SCU must be
selected to support i.MX SCU SoC driver, also need to use
platform driver model to make sure IMX_SCU driver is probed
before i.MX SCU SoC driver.
With this patch, SoC info can be read from sysfs:
i.mx8qxp-mek# cat /sys/devices/soc0/family
Freescale i.MX
i.mx8qxp-mek# cat /sys/devices/soc0/soc_id
0x2
i.mx8qxp-mek# cat /sys/devices/soc0/machine
Freescale i.MX8QXP MEK
i.mx8qxp-mek# cat /sys/devices/soc0/revision
1.1
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Like on imx6/7 we can read version information from a register in
anatop, and in the same format.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Right now in upstream imx8m cpufreq support just lists a common subset
of OPPs because the higher ones should only be attempted after checking
speed grading in fuses.
Add a small driver which checks speed grading from nvmem cells before
registering cpufreq-dt.
This driver allows unlocking all frequencies for imx8mm and imx8mq and
could be applied to other chips like imx7d
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Various driver updates for platforms and a couple of the small driver
subsystems we merge through our tree:
Among the larger pieces:
- Power management improvements for TI am335x and am437x (RTC suspend/wake)
- Misc new additions for Amlogic (socinfo updates)
- ZynqMP FPGA manager
- Nvidia improvements for reset/powergate handling
- PMIC wrapper for Mediatek MT8516
- Misc fixes/improvements for ARM SCMI, TEE, NXP i.MX SCU drivers
-----BEGIN PGP SIGNATURE-----
iQJDBAABCAAtFiEElf+HevZ4QCAJmMQ+jBrnPN6EHHcFAlzc+9QPHG9sb2ZAbGl4
b20ubmV0AAoJEIwa5zzehBx3o3sQAIJ2SZnITy/ycvkbhKe+V/806P+aoqMpbZDw
7ldBQFoIMQqVIoeSSeml+9B86ZGyK4CGTgnvsfAI/Zt2fZSHczjqLP5InbEnvB5M
4naf0nSjSlkb5F4p24wXQ7WTI8IO45SwqG4hCi/WW6MakxN21cwdMWHBn+TRZWQu
+AlJdwyDFJoMRXcq8xvLHOBNVAqD3LyvlECbLKqn3+UPwwYw0Ti1dsLwaMLOYDbc
o/1dC2O8111kg2DgO0OM4Tl7jdbpmGA5MeixbVnmu3t4b2s26trG33eXqK2yWqaV
XigD85R74GAq/wmgnzjdiNaIgZjlPPitVYaTE4L6Od39zMgXemnsqMlh/byPeO2y
JvRRLEIciNay9q9uq+8H2zRWwa2wLqAewjssTTMM0RJNQWUtonVCkD8DAx4GLDof
6Ej42XGbtxnqpf0g854mBJ4zaPfZLN4xK//1Llx9HkM8mhLZLJ7BQvgvW1JzniSa
XKnmjqK7SySiJ4bbjn+aFk5EkX7Oh5aXno18tVNKXdxc8nWoEw4PHMUmCCHOFPye
/1oxc95Ux8P/lV+B0ZjiI0yTAX/IpDkEszAYmgdy6pWh1hXnYUr/Rpm7cGUG8kzk
SbtyB8JOI/DFQ7QMDfPp6e6bcB8zTbUuF9H2MXwPN5TqGzP/mya88DC5Iv1jY4jc
0oWv/uhj
=YSfu
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC-related driver updates from Olof Johansson:
"Various driver updates for platforms and a couple of the small driver
subsystems we merge through our tree:
Among the larger pieces:
- Power management improvements for TI am335x and am437x (RTC
suspend/wake)
- Misc new additions for Amlogic (socinfo updates)
- ZynqMP FPGA manager
- Nvidia improvements for reset/powergate handling
- PMIC wrapper for Mediatek MT8516
- Misc fixes/improvements for ARM SCMI, TEE, NXP i.MX SCU drivers"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (57 commits)
soc: aspeed: fix Kconfig
soc: add aspeed folder and misc drivers
spi: zynqmp: Fix build break
soc: imx: Add generic i.MX8 SoC driver
MAINTAINERS: Update email for Qualcomm SoC maintainer
memory: tegra: Fix a typos for "fdcdwr2" mc client
Revert "ARM: tegra: Restore memory arbitration on resume from LP1 on Tegra30+"
memory: tegra: Replace readl-writel with mc_readl-mc_writel
memory: tegra: Fix integer overflow on tick value calculation
memory: tegra: Fix missed registers values latching
ARM: tegra: cpuidle: Handle tick broadcasting within cpuidle core on Tegra20/30
optee: allow to work without static shared memory
soc/tegra: pmc: Move powergate initialisation to probe
soc/tegra: pmc: Remove reset sysfs entries on error
soc/tegra: pmc: Fix reset sources and levels
soc: amlogic: meson-gx-pwrc-vpu: Add support for G12A
soc: amlogic: meson-gx-pwrc-vpu: Fix power on/off register bitmask
fpga manager: Adding FPGA Manager support for Xilinx zynqmp
dt-bindings: fpga: Add bindings for ZynqMP fpga driver
firmware: xilinx: Add fpga API's
...
This allows PU domain to be turned off in suspend and save power.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add generic i.MX8 SoC driver along with the i.MX8MQ SoC specific code.
For now, only i.MX8MQ revision B1 is supported. For any other, i.MX8MQ
revision it will print 'unknown'.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Use the new helper devm_platform_ioremap_resource() which wraps the
platform_get_resource() and devm_ioremap_resource() together, to
simplify the code.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Use the new helper devm_platform_ioremap_resource() which wraps the
platform_get_resource() and devm_ioremap_resource() together, to
simplify the code.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Replace explicit polling loop with a call to
regmap_read_poll_timeout() to avoid code repetition. Also fix
misspelled "failed" while at it.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Chris Healy <cphealy@gmail.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Since this is going to be used on more SoCs than just i.MX8MQ, make
the dependency here more generic by using ARCH_MXC instead.
Also remove the SOC_IMX7D since it is also included by the ARCH_MXC.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Some power domains handled by the GPCv2 driver need to enable the clocks
for devies inside the domain, so that the reset propagation and proper
power-up sequencing happens. Handle them in the same way as on GPCv1.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Some of the i.MX8MQ domains have an additional control bit in the PU
handshake (HSK) register. Documentation about this bit is a bit sparse
at the moment, but it seems that it controls a power-down request to
the AMBA domain bridge (ADB-400) attached to those domains.
As the documentation doesn't desribe the usage of this bit yet, handle
it in the same way as done in the ATF implementation.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The DISPLAY power domain on imx6sx has 7 clocks.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The GPCv2 on the Freescale i.MX8MQ SoC works in the same way as the
GPCv2 on the i.MX7, but only controls more power domains with a
different mapping.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The valid register ranges are defined by the implemented power domains,
which are different between the individual SoCs where the GPCv2 is used.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
So we can add i.MX8M support without introducing name clashes.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX8MQ and i.MX8MM share same gpc module with i.MX7D, they
can reuse gpcv2 pgc driver for power domain control, this
patch renames all functions and structure definitions started
with "imx7" to "imx", and use .data in imx_gpcv2_dt_ids[] to
pass platform specific power domain data for power domain
driver, thus make gpcv2 pgc driver more generic for i.MX
platforms.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Acked-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
gpcv2 driver is NOT just used on i.MX7D which has Cortex-A7
cores, but also on i.MX8MQ/i.MX8MM platforms which use Cortex-A53
cores, so let's use A_CORE instread of A7 to avoid confusion.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Acked-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx6_pm_domain_power_off() reads iso and iso2sw from GPC_PGC_PUPSCR_OFFS
which stores the power up delays.
So use GPC_PGC_PDNSCR_OFFS for the correct delays.
Signed-off-by: Sven Schmitt <sven.schmitt@mixed-mode.de>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Some of the larger changes this merge window:
- Removal of drivers for Exynos5440, a Samsung SoC that never saw
widespread use.
- Uniphier support for USB3 and SPI reset handling
- Syste control and SRAM drivers and bindings for Allwinner platforms
- Qualcomm AOSS (Always-on subsystem) reset controller drivers
- Raspberry Pi hwmon driver for voltage
- Mediatek pwrap (pmic) support for MT6797 SoC
-----BEGIN PGP SIGNATURE-----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=ZjwY
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"Some of the larger changes this merge window:
- Removal of drivers for Exynos5440, a Samsung SoC that never saw
widespread use.
- Uniphier support for USB3 and SPI reset handling
- Syste control and SRAM drivers and bindings for Allwinner platforms
- Qualcomm AOSS (Always-on subsystem) reset controller drivers
- Raspberry Pi hwmon driver for voltage
- Mediatek pwrap (pmic) support for MT6797 SoC"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (52 commits)
drivers/firmware: psci_checker: stash and use topology_core_cpumask for hotplug tests
soc: fsl: cleanup Kconfig menu
soc: fsl: dpio: Convert DPIO documentation to .rst
staging: fsl-mc: Remove remaining files
staging: fsl-mc: Move DPIO from staging to drivers/soc/fsl
staging: fsl-dpaa2: eth: move generic FD defines to DPIO
soc: fsl: qe: gpio: Add qe_gpio_set_multiple
usb: host: exynos: Remove support for Exynos5440
clk: samsung: Remove support for Exynos5440
soc: sunxi: Add the A13, A23 and H3 system control compatibles
reset: uniphier: add reset control support for SPI
cpufreq: exynos: Remove support for Exynos5440
ata: ahci-platform: Remove support for Exynos5440
soc: imx6qp: Use GENPD_FLAG_ALWAYS_ON for PU errata
soc: mediatek: pwrap: add mt6351 driver for mt6797 SoCs
soc: mediatek: pwrap: add pwrap driver for mt6797 SoCs
soc: mediatek: pwrap: fix cipher init setting error
dt-bindings: pwrap: mediatek: add pwrap support for MT6797
reset: uniphier: add USB3 core reset control
dt-bindings: reset: uniphier: add USB3 core reset support
...
Merge changes in the PM core, system-wide PM infrastructure, generic
power domains (genpd) framework, ACPI PM infrastructure and cpuidle
for 4.19.
* pm-core:
driver core: Add flag to autoremove device link on supplier unbind
driver core: Rename flag AUTOREMOVE to AUTOREMOVE_CONSUMER
* pm-domains:
PM / Domains: Introduce dev_pm_domain_attach_by_name()
PM / Domains: Introduce option to attach a device by name to genpd
PM / Domains: dt: Add a power-domain-names property
* pm-sleep:
PM / reboot: Eliminate race between reboot and suspend
PM / hibernate: Mark expected switch fall-through
x86/power/hibernate_64: Remove VLA usage
PM / hibernate: cast PAGE_SIZE to int when comparing with error code
* acpi-pm:
ACPI / PM: save NVS memory for ASUS 1025C laptop
ACPI / PM: Default to s2idle in all machines supporting LP S0
* pm-cpuidle:
ARM: cpuidle: silence error on driver registration failure
