Up to now the pasemi nand driver only supported a single device
instance. However the check for that was racy because two parallel calls
of pasemi_nand_probe() could pass the check
if (pasemi_nand_mtd)
return -ENODEV;
before any of them assigns a non-NULL value to it.
So rework the driver to make use of per-device driver data.
As an intended side effect the driver can bind more than one device and
also gets rid of the check
if (!pasemi_nand_mtd)
return 0;
in the remove callback that could only ever trigger after the above race
happened.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230102124051.1508424-1-u.kleine-koenig@pengutronix.de
Building with -Werror=override-init reveals that two patches added
the same device ID table to this driver:
drivers/mtd/devices/mtd_dataflash.c:946:27: error: initialized field overwritten [-Werror=override-init]
946 | .id_table = dataflash_spi_ids,
| ^~~~~~~~~~~~~~~~~
drivers/mtd/devices/mtd_dataflash.c:946:27: note: (near initialization for 'dataflash_driver.id_table')
Remove one of the copies.
Fixes: 27a030e872 ("mtd: dataflash: Add device-tree SPI IDs")
Fixes: ac4f83482a ("mtd: dataflash: Add SPI ID table")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20221215164736.1315815-1-arnd@kernel.org
Each chip is required to have a unique CS number ("reg" property) in the
range 0-7, so there is no need to separately count the number of chips.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20221229181526.53766-4-samuel@sholland.org
If a chip fails to initialize, we need to clean up any chips that were
already initialized/registered.
Fixes: 1fef62c142 ("mtd: nand: add sunxi NAND flash controller support")
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20221229181526.53766-2-samuel@sholland.org
A missing layouts were added to the driver to support NAND flashes
with ECC layouts of 12 or 16 with page sized of 2048, 4096 or 8192.
Usually theses are rare layouts, but in Marvell AC5 driver, the ECC
level is set according to the spare area, so we may use these layouts
more frequently.
Signed-off-by: Aviram Dali <aviramd@marvell.com>
Signed-off-by: Vadym Kochan <vadym.kochan@plvision.eu>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20221216162715.3230766-1-vadym.kochan@plvision.eu
When MTD or MTD_CFI_GEOMETRY is disabled, the spi-intel driver
fails to build, as it includes the shared CFI header:
include/linux/mtd/cfi.h:62:2: error: #warning No CONFIG_MTD_CFI_Ix selected. No NOR chip support can work. [-Werror=cpp]
62 | #warning No CONFIG_MTD_CFI_Ix selected. No NOR chip support can work.
linux/mtd/spi-nor.h does not actually need to include cfi.h, so
remove the inclusion here to fix the warning. This uncovers a
missing #include in spi-nor/core.c so add that there to
prevent a different build issue.
Fixes: e23e5a05d1 ("mtd: spi-nor: intel-spi: Convert to SPI MEM")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Tokunori Ikegami <ikegami.t@gmail.com>
Acked-by: Pratyush Yadav <pratyush@kernel.org>
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20221220141352.1486360-1-arnd@kernel.org
This fixes the following compile error on mips architecture with clang
version 16.0.0 reported by the 0-DAY CI Kernel Test Service:
ld.lld: error: undefined symbol: __udivdi3
referenced by scpart.c
mtd/parsers/scpart.o:(scpart_parse) in archive drivers/built-in.a
As a workaround this makes 'offs' a 32-bit type. This is enough, because
the mtd containing partition table practically does not exceed 1 MB. We
can revert this when the [Link] has been resolved.
Link: https://github.com/ClangBuiltLinux/linux/issues/1635
Fixes: 9b78ef0c79 ("mtd: parsers: add support for Sercomm partitions")
Reported-by: kernel test robot <lkp@intel.com>
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/805fe58e-690f-6a3f-5ebf-2f6f6e6e4599@gmail.com
The parts needs to be freed with all its elements, otherwise it will be
leaked.
Fixes: 00a3588084 ("mtd: parsers: add TP-Link SafeLoader partitions table parser")
Signed-off-by: Yuan Can <yuancan@huawei.com>
Reviewed-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20221208113620.78855-1-yuancan@huawei.com
BFPT_DWORD() converts 1-based indexing to 0-based indexing for C arrays,
and is used in BFPT parse. Per JESD216F.02, the conversion is applicable
to other parameter tables than BFPT. This patch renames the macro to
SFDP_DWORD() so that we can use it for other parameter tables than BFPT.
Suggested-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://lore.kernel.org/r/e42feac840fe3a31187419e91b2d514d9f259d15.1672026365.git.Takahiro.Kuwano@infineon.com
* Fix refcount error in del_mtd_device()
* Fix possible resource leak in init_mtd()
* Set ROOT_DEV for partitions marked as rootfs in DT
* Describe marking rootfs partitions in the bindings
* Fix device name leak when register device failed in add_mtd_device()
* Try to find OF node for every MTD partition
* simplify (a bit) code find partition-matching dynamic OF node
MTD driver changes:
* pxa2xx-flash maps: fix memory leak in probe
* BCM parser: refer to ARCH_BCMBCA instead of ARCH_BCM4908
* lpddr2_nvm: Fix possible null-ptr-deref
* inftlcore: fix repeated words in comments
* lart: remove driver
* tplink:
- Add TP-Link SafeLoader partitions table parser and bindings
- Describe TP-Link SafeLoader parser
- Describe TP-Link SafeLoader dynamic subpartitions
* mtdoops:
- Panic caused mtdoops to call mtdoops_erase function immediately
- Add mtdoops_erase function and move mtdoops_inc_counter to after it
- Change printk() to counterpart pr_ functions
MTD binding cleanup:
* Fixed-partitions: Fix 'sercomm,scpart-id' schema
* Standardize the style in the examples
* Drop object types when referencing other files
* Argue in favor of keeping additionalProperties set to true
* NVMEM-cells:
- Inherit from MTD partitions
- Drop range property from example
* Partitions:
- Change qcom,smem-part partition type
- Constrain the list of parsers
* Physmap: Reuse the generic definitions
* SPI-NOR: Drop common properties
* Sunxi-nand: Add an example to validate the bindings
* Onenand: Mention the expected node name
* Ingenic: Mark partitions in the controller node as deprecated
* NAND:
- Standardize the child node name
- Drop common properties already defined in generic files
- nand-chip.yaml should reference mtd.yaml
* Remove useless file about partitions
* Clarify all partition subnodes
SPI NOR core changes:
* Add support for flash reset using the dt reset-gpios property.
* Update hwcaps.mask to include 8D-8D-8D read and page program ops
when xSPI profile 1.0 table is defined.
* Bypass zero erase size in spi_nor_find_best_erase_type().
* Fix select_uniform_erase to skip 0 erase size
* Add generic flash driver. If a flash is not found in the flash_info
array, fall back to the generic flash driver which is described solely
by the flash's SFDP tables.
* Fix the number of bytes for the dummy cycles in
spi_nor_spimem_check_readop().
* Introduce SPI_NOR_QUAD_PP flag, as PP_1_1_4 is not SFDP discoverable.
SPI NOR manufacturer drivers changes:
* Spansion:
- use PARSE_SFDP for s28hs512t,
- add support for s28hl512t, s28hl01gt, and s28hs01gt.
* Gigadevice: Replace default_init() with post_bfpt() for gd25q256.
* Micron - ST: Enable locking for mt25qu256a.
* Winbond: Add support for W25Q512NW-IQ.
* ISSI: Use PARSE_SFDP and SPI_NOR_QUAD_PP.
Raw NAND core changes:
* Drop obsolete dependencies on COMPILE_TEST
* MAINTAINERS: rectify entry for MESON NAND controller bindings
* Drop EXPORT_SYMBOL_GPL for nanddev_erase()
Raw NAND driver changes:
* marvell: Enable NFC/DEVBUS arbiter
* gpmi: Use pm_runtime_resume_and_get instead of pm_runtime_get_sync
* mpc5121: Replace NO_IRQ by 0
* lpc32xx_{slc,mlc}:
- Switch to using pm_ptr()
- Switch to using gpiod API
* lpc32xx_mlc: Switch to using pm_ptr()
* cadence: Support 64-bit slave dma interface
* rockchip: Describe rk3128-nfc in the bindings
* brcmnand: Update interrupts description in the bindings
SPI-NAND driver changes:
* winbond:
- Add Winbond W25N02KV flash support
- Fix flash identification
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmOOBbQACgkQJWrqGEe9
VoRB7wf9EY8IeRhumaeN9WT+VrmPxGOu61m/eilUK4xvgj6JX/yhYo/kKW9eEp+o
5I8JLimG6uo7rZNlbixGMbHd41aTu9MplLrTA42nzGadl3w4D8p9c1ic6sEiv7SI
qgnAbzq3FLUPDLLDV0IfrMQvsQgJkv3b+r8ShPt9uJy3cmnKQzOvIhs43wwLnOXp
NPiMbVjpS4FAmNvG7nI0xfcBLO/eFaTuQc+UyfP2SwkVIAN5xfUAwOPOHZWBstmR
zhJlHSFJWrg+J9T9bsRW7D5q/MVxqNsMH589c9aXHNqzgzZs2FTopDUf6cWwHr0f
2Ssot2naIdvU+eLGA12hDuUDDoRwKA==
=Igti
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull mtd updates from Miquel Raynal:
"MTD core changes:
- Fix refcount error in del_mtd_device()
- Fix possible resource leak in init_mtd()
- Set ROOT_DEV for partitions marked as rootfs in DT
- Describe marking rootfs partitions in the bindings
- Fix device name leak when register device fails in add_mtd_device()
- Try to find OF node for every MTD partition
- simplify (a bit) code find partition-matching dynamic OF node
MTD driver changes:
- pxa2xx-flash maps: fix memory leak in probe
- BCM parser: refer to ARCH_BCMBCA instead of ARCH_BCM4908
- lpddr2_nvm: Fix possible null-ptr-deref
- inftlcore: fix repeated words in comments
- lart: remove driver
- tplink:
- Add TP-Link SafeLoader partitions table parser and bindings
- Describe TP-Link SafeLoader parser
- Describe TP-Link SafeLoader dynamic subpartitions
- mtdoops:
- Panic caused mtdoops to call mtdoops_erase function immediately
- Add mtdoops_erase function and move mtdoops_inc_counter after it
- Change printk() to counterpart pr_ functions
MTD binding cleanup:
- Fixed-partitions: Fix 'sercomm,scpart-id' schema
- Standardize the style in the examples
- Drop object types when referencing other files
- Argue in favor of keeping additionalProperties set to true
- NVMEM-cells:
- Inherit from MTD partitions
- Drop range property from example
- Partitions:
- Change qcom,smem-part partition type
- Constrain the list of parsers
- Physmap: Reuse the generic definitions
- SPI-NOR: Drop common properties
- Sunxi-nand: Add an example to validate the bindings
- Onenand: Mention the expected node name
- Ingenic: Mark partitions in the controller node as deprecated
- NAND:
- Standardize the child node name
- Drop common properties already defined in generic files
- nand-chip.yaml should reference mtd.yaml
- Remove useless file about partitions
- Clarify all partition subnodes
SPI NOR core changes:
- Add support for flash reset using the dt reset-gpios property.
- Update hwcaps.mask to include 8D-8D-8D read and page program ops
when xSPI profile 1.0 table is defined.
- Bypass zero erase size in spi_nor_find_best_erase_type().
- Fix select_uniform_erase to skip 0 erase size
- Add generic flash driver. If a flash is not found in the flash_info
array, fall back to the generic flash driver which is described
solely by the flash's SFDP tables.
- Fix the number of bytes for the dummy cycles in
spi_nor_spimem_check_readop().
- Introduce SPI_NOR_QUAD_PP flag, as PP_1_1_4 is not SFDP
discoverable.
SPI NOR manufacturer drivers changes:
- Spansion:
- use PARSE_SFDP for s28hs512t,
- add support for s28hl512t, s28hl01gt, and s28hs01gt.
- Gigadevice: Replace default_init() with post_bfpt() for gd25q256.
- Micron - ST: Enable locking for mt25qu256a.
- Winbond: Add support for W25Q512NW-IQ.
- ISSI: Use PARSE_SFDP and SPI_NOR_QUAD_PP.
Raw NAND core changes:
- Drop obsolete dependencies on COMPILE_TEST
- MAINTAINERS: rectify entry for MESON NAND controller bindings
- Drop EXPORT_SYMBOL_GPL for nanddev_erase()
Raw NAND driver changes:
- marvell: Enable NFC/DEVBUS arbiter
- gpmi: Use pm_runtime_resume_and_get instead of pm_runtime_get_sync
- mpc5121: Replace NO_IRQ by 0
- lpc32xx_{slc,mlc}:
- Switch to using pm_ptr()
- Switch to using gpiod API
- lpc32xx_mlc: Switch to using pm_ptr()
- cadence: Support 64-bit slave dma interface
- rockchip: Describe rk3128-nfc in the bindings
- brcmnand: Update interrupts description in the bindings
SPI-NAND driver changes:
- winbond:
- Add Winbond W25N02KV flash support
- Fix flash identification"
* tag 'mtd/for-6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (76 commits)
mtd: rawnand: Drop obsolete dependencies on COMPILE_TEST
mtd: maps: pxa2xx-flash: fix memory leak in probe
mtd: core: Fix refcount error in del_mtd_device()
mtd: spi-nor: add SFDP fixups for Quad Page Program
mtd: spi-nor: issi: is25wp256: Init flash based on SFDP
mtd: spi-nor: winbond: add support for W25Q512NW-IQ
mtd: spi-nor: micron-st: Enable locking for mt25qu256a
mtd: spi-nor: Fix the number of bytes for the dummy cycles
mtd: spi-nor: gigadevice: gd25q256: replace gd25q256_default_init with gd25q256_post_bfpt
mtd: spi-nor: Fix formatting in spi_nor_read_raw() kerneldoc comment
mtd: spi-nor: sysfs: print JEDEC ID for generic flash driver
mtd: spi-nor: add generic flash driver
mtd: spi-nor: fix select_uniform_erase to skip 0 erase size
mtd: spi-nor: move function declaration out of sfdp.h
mtd: spi-nor: remember full JEDEC flash ID
mtd: spi-nor: sysfs: hide manufacturer if it is not set
mtd: spi-nor: hide jedec_id sysfs attribute if not present
mtd: spi-nor: Check for zero erase size in spi_nor_find_best_erase_type()
mtd: rawnand: marvell: Enable NFC/DEVBUS arbiter
mtd: parsers: refer to ARCH_BCMBCA instead of ARCH_BCM4908
...
-----BEGIN PGP SIGNATURE-----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=QRhK
-----END PGP SIGNATURE-----
Merge tag 'random-6.2-rc1-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/crng/random
Pull random number generator updates from Jason Donenfeld:
- Replace prandom_u32_max() and various open-coded variants of it,
there is now a new family of functions that uses fast rejection
sampling to choose properly uniformly random numbers within an
interval:
get_random_u32_below(ceil) - [0, ceil)
get_random_u32_above(floor) - (floor, U32_MAX]
get_random_u32_inclusive(floor, ceil) - [floor, ceil]
Coccinelle was used to convert all current users of
prandom_u32_max(), as well as many open-coded patterns, resulting in
improvements throughout the tree.
I'll have a "late" 6.1-rc1 pull for you that removes the now unused
prandom_u32_max() function, just in case any other trees add a new
use case of it that needs to converted. According to linux-next,
there may be two trivial cases of prandom_u32_max() reintroductions
that are fixable with a 's/.../.../'. So I'll have for you a final
conversion patch doing that alongside the removal patch during the
second week.
This is a treewide change that touches many files throughout.
- More consistent use of get_random_canary().
- Updates to comments, documentation, tests, headers, and
simplification in configuration.
- The arch_get_random*_early() abstraction was only used by arm64 and
wasn't entirely useful, so this has been replaced by code that works
in all relevant contexts.
- The kernel will use and manage random seeds in non-volatile EFI
variables, refreshing a variable with a fresh seed when the RNG is
initialized. The RNG GUID namespace is then hidden from efivarfs to
prevent accidental leakage.
These changes are split into random.c infrastructure code used in the
EFI subsystem, in this pull request, and related support inside of
EFISTUB, in Ard's EFI tree. These are co-dependent for full
functionality, but the order of merging doesn't matter.
- Part of the infrastructure added for the EFI support is also used for
an improvement to the way vsprintf initializes its siphash key,
replacing an sleep loop wart.
- The hardware RNG framework now always calls its correct random.c
input function, add_hwgenerator_randomness(), rather than sometimes
going through helpers better suited for other cases.
- The add_latent_entropy() function has long been called from the fork
handler, but is a no-op when the latent entropy gcc plugin isn't
used, which is fine for the purposes of latent entropy.
But it was missing out on the cycle counter that was also being mixed
in beside the latent entropy variable. So now, if the latent entropy
gcc plugin isn't enabled, add_latent_entropy() will expand to a call
to add_device_randomness(NULL, 0), which adds a cycle counter,
without the absent latent entropy variable.
- The RNG is now reseeded from a delayed worker, rather than on demand
when used. Always running from a worker allows it to make use of the
CPU RNG on platforms like S390x, whose instructions are too slow to
do so from interrupts. It also has the effect of adding in new inputs
more frequently with more regularity, amounting to a long term
transcript of random values. Plus, it helps a bit with the upcoming
vDSO implementation (which isn't yet ready for 6.2).
- The jitter entropy algorithm now tries to execute on many different
CPUs, round-robining, in hopes of hitting even more memory latencies
and other unpredictable effects. It also will mix in a cycle counter
when the entropy timer fires, in addition to being mixed in from the
main loop, to account more explicitly for fluctuations in that timer
firing. And the state it touches is now kept within the same cache
line, so that it's assured that the different execution contexts will
cause latencies.
* tag 'random-6.2-rc1-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/crng/random: (23 commits)
random: include <linux/once.h> in the right header
random: align entropy_timer_state to cache line
random: mix in cycle counter when jitter timer fires
random: spread out jitter callback to different CPUs
random: remove extraneous period and add a missing one in comments
efi: random: refresh non-volatile random seed when RNG is initialized
vsprintf: initialize siphash key using notifier
random: add back async readiness notifier
random: reseed in delayed work rather than on-demand
random: always mix cycle counter in add_latent_entropy()
hw_random: use add_hwgenerator_randomness() for early entropy
random: modernize documentation comment on get_random_bytes()
random: adjust comment to account for removed function
random: remove early archrandom abstraction
random: use random.trust_{bootloader,cpu} command line option only
stackprotector: actually use get_random_canary()
stackprotector: move get_random_canary() into stackprotector.h
treewide: use get_random_u32_inclusive() when possible
treewide: use get_random_u32_{above,below}() instead of manual loop
treewide: use get_random_u32_below() instead of deprecated function
...
* Add support for flash reset using the dt reset-gpios property.
* Update hwcaps.mask to include 8D-8D-8D read and page program ops
when xSPI profile 1.0 table is defined.
* Bypass zero erase size in spi_nor_find_best_erase_type().
* Fix select_uniform_erase to skip 0 erase size
* Add generic flash driver. If a flash is not found in the flash_info
array, fall back to the generic flash driver which is described solely
by the flash's SFDP tables.
* Fix the number of bytes for the dummy cycles in
spi_nor_spimem_check_readop().
* Introduce SPI_NOR_QUAD_PP flag, as PP_1_1_4 is not SFDP discoverable.
SPI NOR manufacturer drivers changes:
* Spansion:
- use PARSE_SFDP for s28hs512t,
- add support for s28hl512t, s28hl01gt, and s28hs01gt.
* Gigadevice: Replace default_init() with post_bfpt() for gd25q256.
* Micron - ST: Enable locking for mt25qu256a.
* Winbond: Add support for W25Q512NW-IQ.
* ISSI: Use PARSE_SFDP and SPI_NOR_QUAD_PP.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEHUIqys8OyG1eHf7fS1VPR6WNFOkFAmOJ59AACgkQS1VPR6WN
FOnzOQf/WLBTNFtPcJoS7cdjlh4fuGySDUKuLifOX+Tmk/ki3XFCZR98cESgb5m+
hCyFDeER/qfdOK9ObT3K1GBS6x7zx8YkskbucjAU0vlIsr2ZHCjNpNiAHrADsKjR
579N0Xwh2ibh7uVJ1xvsPwObdAc8P/tjGHHWF6hGEZzIPYXJVce+qDktkkLfbZ/P
Fik6+y3h68wW/0kDNt/gNmNcb5Z3fjxySs21Np5sy7bUtVVBjHWLo0OpjNadDH9M
m6AkhFA5h9OVl5E4jHBpxc4NvlAa5f6520vESpieseNJiIMWo0W/eSkVsframFew
ILdtXCHjkbS6kgvSpUViobMFsgCjaA==
=Yi2q
-----END PGP SIGNATURE-----
Merge tag 'spi-nor/for-6.2' into mtd/next
SPI NOR core changes:
* Add support for flash reset using the dt reset-gpios property.
* Update hwcaps.mask to include 8D-8D-8D read and page program ops
when xSPI profile 1.0 table is defined.
* Bypass zero erase size in spi_nor_find_best_erase_type().
* Fix select_uniform_erase to skip 0 erase size
* Add generic flash driver. If a flash is not found in the flash_info
array, fall back to the generic flash driver which is described solely
by the flash's SFDP tables.
* Fix the number of bytes for the dummy cycles in
spi_nor_spimem_check_readop().
* Introduce SPI_NOR_QUAD_PP flag, as PP_1_1_4 is not SFDP discoverable.
SPI NOR manufacturer drivers changes:
* Spansion:
- use PARSE_SFDP for s28hs512t,
- add support for s28hl512t, s28hl01gt, and s28hs01gt.
* Gigadevice: Replace default_init() with post_bfpt() for gd25q256.
* Micron - ST: Enable locking for mt25qu256a.
* Winbond: Add support for W25Q512NW-IQ.
* ISSI: Use PARSE_SFDP and SPI_NOR_QUAD_PP.
Fix merge conflict in the jedec,spi-nor bindings.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
* Drop obsolete dependencies on COMPILE_TEST
* MAINTAINERS: rectify entry for MESON NAND controller bindings
* Drop EXPORT_SYMBOL_GPL for nanddev_erase()
Raw NAND driver changes:
* marvell: Enable NFC/DEVBUS arbiter
* gpmi: Use pm_runtime_resume_and_get instead of pm_runtime_get_sync
* mpc5121: Replace NO_IRQ by 0
* lpc32xx_{slc,mlc}:
- Switch to using pm_ptr()
- Switch to using gpiod API
* lpc32xx_mlc: Switch to using pm_ptr()
* cadence: Support 64-bit slave dma interface
* rockchip: Describe rk3128-nfc in the bindings
* brcmnand: Update interrupts description in the bindings
SPI-NAND driver changes:
* winbond:
- Add Winbond W25N02KV flash support
- Fix flash identification
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmOGGfIACgkQJWrqGEe9
VoSZVQgAmew5RtMegFus/AXflUsGYCvZKfV1LVnxmSoGIKBrJr3yjzh6mFuLyzaP
qt2KljEJ4dblk2M3efosX5YeAkz7A7evm218NHGeKWHMPCDimSE1ptAyBhhMmsVi
cgCgu3LXh369dK9OAm7ZVR4hOdDuK5rpYIcXA4mUh0yqiFxfxsuuNY7QBDVrN+qt
SNmZkTBbCgGRxo7RRanN2ljnSm31p6TyhngUDKG89puMka9gGA9yWLbWFDpwM5SS
L0Tr2ZOHctzz/X/1s2yPcnN6ZPpqsc1wLnGyLOWlhkm7oo7aiT59rlHj9GHbp82h
7lXf7MeWxSNSVr9PMHHUR7XDqlLaOw==
=aOZ+
-----END PGP SIGNATURE-----
Merge tag 'nand/for-6.2' into mtd/next
Raw NAND core changes:
* Drop obsolete dependencies on COMPILE_TEST
* MAINTAINERS: rectify entry for MESON NAND controller bindings
* Drop EXPORT_SYMBOL_GPL for nanddev_erase()
Raw NAND driver changes:
* marvell: Enable NFC/DEVBUS arbiter
* gpmi: Use pm_runtime_resume_and_get instead of pm_runtime_get_sync
* mpc5121: Replace NO_IRQ by 0
* lpc32xx_{slc,mlc}:
- Switch to using pm_ptr()
- Switch to using gpiod API
* lpc32xx_mlc: Switch to using pm_ptr()
* cadence: Support 64-bit slave dma interface
* rockchip: Describe rk3128-nfc in the bindings
* brcmnand: Update interrupts description in the bindings
SPI-NAND driver changes:
* winbond:
- Add Winbond W25N02KV flash support
- Fix flash identification
Fix merge conflict with mtd tree regarding the brcm bindings.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Since commit 0166dc11be ("of: make CONFIG_OF user selectable"), it
is possible to test-build any driver which depends on OF on any
architecture by explicitly selecting OF. Therefore depending on
COMPILE_TEST as an alternative is no longer needed.
It is actually better to always build such drivers with OF enabled,
so that the test builds are closer to how each driver will actually be
built on its intended target. Building them without OF may not test
much as the compiler will optimize out potentially large parts of the
code. In the worst case, this could even pop false positive warnings.
Dropping COMPILE_TEST here improves the quality of our testing and
avoids wasting time on non-existent issues.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: Naga Sureshkumar Relli <nagasure@xilinx.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20221124115946.5edb771c@endymion.delvare
SFDP table of some flash chips do not advertise support of Quad Input
Page Program even though it has support. Use flags and add hardware
cap for these chips.
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@sifive.com>
[tudor.ambarus@microchip.com: move pp setting in spi_nor_init_default_params]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20220920184808.44876-2-sudip.mukherjee@sifive.com
The datasheet of is25wp256 says it supports SFDP. Get rid of the static
initialization of the flash parameters and init them when parsing SFDP.
Testing showed the flash using SPINOR_OP_READ_1_1_4_4B 0x6c,
SPINOR_OP_PP_4B 0x12 and SPINOR_OP_BE_4K_4B 0x21 before enabling SFDP.
After this patch, it parses the SFDP information and still uses the
same opcodes.
Set sector_size and n_sectors to zero as they will be discovered when
parsing SFDP.
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@sifive.com>
[tudor.ambarus@microchip.com: set sector_size and n_sectors to zero]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20220920184808.44876-1-sudip.mukherjee@sifive.com
The number of bytes used by spi_nor_spimem_check_readop() may be
incorrect for the dummy cycles. Since nor->read_dummy is not initialized
before spi_nor_spimem_adjust_hwcaps().
We use both mode and wait state clock cycles instead of nor->read_dummy.
Fixes: 0e30f47232 ("mtd: spi-nor: add support for DTR protocol")
Co-developed-by: Bayi Cheng <bayi.cheng@mediatek.com>
Signed-off-by: Bayi Cheng <bayi.cheng@mediatek.com>
Signed-off-by: Allen-KH Cheng <allen-kh.cheng@mediatek.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested-by: Dhruva Gole <d-gole@ti.com>
Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Pratyush Yadav <pratyush@kernel.org>
Link: https://lore.kernel.org/r/20221031124633.13189-1-allen-kh.cheng@mediatek.com
When utilizing PARSE_SFDP to initialize the flash parameter, the
deprecated initializing method spi_nor_init_params_deprecated() and the
function spi_nor_manufacturer_init_params() within it will never be
executed, which results in the default_init hook function will also never
be executed.
This is okay for 'D' generation of GD25Q256, because 'D' generation is
implementing the JESD216B standards, it has QER field defined in BFPT,
parsing the SFDP can properly set the quad_enable function. The 'E'
generation also implements the JESD216B standards, and it has the same
status register definitions as 'D' generation, parsing the SFDP to set
the quad_enable function should also work for 'E' generation.
However, the same thing can't apply to 'C' generation. 'C' generation
'GD25Q256C' implements the JESD216 standards, and it doesn't have the
QER field defined in BFPT, since it does have QE bit in status register
1, the quad_enable hook needs to be tweaked to properly set the
quad_enable function, this can be done in post_bfpt fixup hook.
Fixes: 047275f7de ("mtd: spi-nor: gigadevice: gd25q256: Init flash based on SFDP")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Yaliang Wang <Yaliang.Wang@windriver.com>
[tudor.ambarus@microchip.com: Update comment in gd25q256_post_bfpt]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20221016171901.1483542-2-yaliang.wang@windriver.com
It doesn't make sense to put "set" on its own line like that.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Pratyush Yadav <pratyush@kernel.org>
Link: https://lore.kernel.org/r/20221101162906.990125-1-j.neuschaefer@gmx.net
We don't have a database entry for the generic SPI-NOR flash driver and
thus we don't have a JEDEC ID to print. Print the (cached) JEDEC ID
instead.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Link: https://lore.kernel.org/r/20220810220654.1297699-8-michael@walle.cc
Our SFDP parsing is everything we need to support all basic operations
of a flash device. If the flash isn't found in our in-kernel flash
database, gracefully fall back to a driver described solely by its SFDP
tables.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Link: https://lore.kernel.org/r/20220810220654.1297699-7-michael@walle.cc
4bait will set the erase size to 0 if there is no corresponding
opcode for the 4byte erase. Fix spi_nor_select_uniform_erase to skip
the 0 erase size to avoid mtd device registration failure cases.
Reported-by: Jae Hyun Yoo <quic_jaehyoo@quicinc.com>
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20220810220654.1297699-6-michael@walle.cc
sfdp.h should only contain constants related to the JEDEC SFDP
specification(s).
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Link: https://lore.kernel.org/r/20220810220654.1297699-5-michael@walle.cc
At the moment, we print the JEDEC ID that is stored in our database. The
generic flash support won't have such an entry in our database. To find
out the JEDEC ID later we will have to cache it. There is also another
advantage: If the flash is found in the database, the ID could be
truncated because the ID of the entry is used which can be shorter. Some
flashes still holds valuable information in the bytes after the JEDEC ID
and come in handy during debugging of when coping with INFO6() entries.
These are not accessible for now.
Save a copy of the ID bytes after reading and display it via debugfs.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Link: https://lore.kernel.org/r/20220810220654.1297699-4-michael@walle.cc
The manufacturer may be optional when pure SFDP flashes are supported.
Hide the sysfs property if no manufacturer is set.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Link: https://lore.kernel.org/r/20220810220654.1297699-3-michael@walle.cc
Some non-jedec compliant flashes (like the Everspin flashes) don't have
an ID at all. Hide the attribute in this case.
Fixes: 36ac022862 ("mtd: spi-nor: add initial sysfs support")
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Link: https://lore.kernel.org/r/20220810220654.1297699-2-michael@walle.cc
Erase can be zeroed in spi_nor_parse_4bait() or
spi_nor_init_non_uniform_erase_map(). In practice it happened with
mt25qu256a, which supports 4K, 32K, 64K erases with 3b address commands,
but only 4K and 64K erase with 4b address commands.
Fixes: dc92843159 ("mtd: spi-nor: fix erase_type array to indicate current map conf")
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20211119081412.29732-1-alexander.sverdlin@nokia.com
These cases were done with this Coccinelle:
@@
expression H;
expression L;
@@
- (get_random_u32_below(H) + L)
+ get_random_u32_inclusive(L, H + L - 1)
@@
expression H;
expression L;
expression E;
@@
get_random_u32_inclusive(L,
H
- + E
- - E
)
@@
expression H;
expression L;
expression E;
@@
get_random_u32_inclusive(L,
H
- - E
- + E
)
@@
expression H;
expression L;
expression E;
expression F;
@@
get_random_u32_inclusive(L,
H
- - E
+ F
- + E
)
@@
expression H;
expression L;
expression E;
expression F;
@@
get_random_u32_inclusive(L,
H
- + E
+ F
- - E
)
And then subsequently cleaned up by hand, with several automatic cases
rejected if it didn't make sense contextually.
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com> # for infiniband
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
This is a simple mechanical transformation done by:
@@
expression E;
@@
- prandom_u32_max
+ get_random_u32_below
(E)
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Darrick J. Wong <djwong@kernel.org> # for xfs
Reviewed-by: SeongJae Park <sj@kernel.org> # for damon
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com> # for infiniband
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> # for arm
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # for mmc
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
The CN9130 SoC (an ARMADA 8K type) has both a NAND Flash Controller and
a generic local bus controller (Device Bus Controller) that share common
pins.
With a board design that incorporates both a NAND flash and uses
the Device Bus (in our case for an SRAM) accessing the Device Bus device
fails unless the NfArbiterEn bit is set. Setting the bit enables
arbitration between the Device Bus and the NAND flash.
Since there is no obvious downside in enabling this for designs that
don't require arbitration, we always enable it.
Signed-off-by: Hamish Martin <hamish.martin@alliedtelesis.co.nz>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20221109231325.7714-1-hamish.martin@alliedtelesis.co.nz
Commit dd5c672d7c ("arm64: bcmbca: Merge ARCH_BCM4908 to ARCH_BCMBCA")
removes config ARCH_BCM4908 as config ARCH_BCMBCA has the same intent.
Probably due to concurrent development, commit 002181f5b1 ("mtd: parsers:
add Broadcom's U-Boot parser") introduces 'Broadcom's U-Boot partition
parser' that depends on ARCH_BCM4908, but this use was not visible during
the config refactoring from the commit above. Hence, these two changes
create a reference to a non-existing config symbol.
Adjust the MTD_BRCM_U_BOOT definition to refer to ARCH_BCMBCA instead of
ARCH_BCM4908 to remove the reference to the non-existing config symbol
ARCH_BCM4908.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20221116124932.4748-1-lukas.bulwahn@gmail.com
There is already a real partitions.yaml file, so assuming everybody
knows hot to read yaml schema now, this text file is no longer needed,
so drop it.
Depending on the situation, the lines referring to this file are either
dropped or edited to point to mtd.yaml which includes partition{,s}.yaml.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/linux-mtd/20221114090315.848208-3-miquel.raynal@bootlin.com
The switch to using the gpiod API removed the last user of
lpc32xx_wp_disable() outside #ifdef CONFIG_PM, causing build failures if
CONFIG_PM=n:
drivers/mtd/nand/raw/lpc32xx_slc.c:318:13: error: ‘lpc32xx_wp_disable’ defined but not used [-Werror=unused-function]
318 | static void lpc32xx_wp_disable(struct lpc32xx_nand_host *host)
| ^~~~~~~~~~~~~~~~~~
Fix this by switching from #ifdef CONFIG_PM to pm_ptr(), increasing
compile-coverage as a side-effect.
Reported-by: noreply@ellerman.id.au
Fixes: 6b923db286 ("mtd: rawnand: lpc32xx_slc: switch to using gpiod API")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20221027131028.3838303-2-geert@linux-m68k.org
The switch to using the gpiod API removed the last user of
lpc32xx_wp_disable() outside #ifdef CONFIG_PM, causing build failures if
CONFIG_PM=n:
drivers/mtd/nand/raw/lpc32xx_mlc.c:380:13: error: ‘lpc32xx_wp_disable’ defined but not used [-Werror=unused-function]
380 | static void lpc32xx_wp_disable(struct lpc32xx_nand_host *host)
| ^~~~~~~~~~~~~~~~~~
Fix this by switching from #ifdef CONFIG_PM to pm_ptr(), increasing
compile-coverage as a side-effect.
Reported-by: noreply@ellerman.id.au
Fixes: 782e32a990 ("mtd: rawnand: lpc32xx_mlc: switch to using gpiod API")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20221027131028.3838303-1-geert@linux-m68k.org
I got the error report while inject fault in init_mtd():
sysfs: cannot create duplicate filename '/devices/virtual/bdi/mtd-0'
Call Trace:
<TASK>
dump_stack_lvl+0x67/0x83
sysfs_warn_dup+0x60/0x70
sysfs_create_dir_ns+0x109/0x120
kobject_add_internal+0xce/0x2f0
kobject_add+0x98/0x110
device_add+0x179/0xc00
device_create_groups_vargs+0xf4/0x100
device_create+0x7b/0xb0
bdi_register_va.part.13+0x58/0x2d0
bdi_register+0x9b/0xb0
init_mtd+0x62/0x171 [mtd]
do_one_initcall+0x6c/0x3c0
do_init_module+0x58/0x222
load_module+0x268e/0x27d0
__do_sys_finit_module+0xd5/0x140
do_syscall_64+0x37/0x90
entry_SYSCALL_64_after_hwframe+0x63/0xcd
</TASK>
kobject_add_internal failed for mtd-0 with -EEXIST, don't try to register
things with the same name in the same directory.
Error registering mtd class or bdi: -17
If init_mtdchar() fails in init_mtd(), mtd_bdi will not be unregistered,
as a result, we can't load the mtd module again, to fix this by calling
bdi_unregister(mtd_bdi) after out_procfs label.
Fixes: 445caaa20c ("mtd: Allocate bdi objects dynamically")
Signed-off-by: Gaosheng Cui <cuigaosheng1@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20221024065109.2050705-1-cuigaosheng1@huawei.com
This adds support for "linux,rootfs" binding that is used to mark flash
partition containing rootfs. It's useful for devices using device tree
that don't have bootloader passing root info in cmdline.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20221022211318.32009-2-zajec5@gmail.com
On 64 bit systems, the highest 32 bits of the "offset" variable are
not initialized. Also the existing code is not endian safe (it will
fail on big endian systems). Change the type of "offset" to a u32.
Fixes: aec4d5f5ffd0 ("mtd: parsers: add TP-Link SafeLoader partitions table parser")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/Y1gCALFWXYYwqV1P@kili
The panic function disables the local interrupts, preemption, and all
other processors. When the invoked mtdoops needs to erase a used page,
calling schedule_work() to do it will not work. Instead, just call
mtdoops_erase function immediately.
Tested:
~# echo c > /proc/sysrq-trigger
[ 171.654759] sysrq: Trigger a crash
[ 171.658325] Kernel panic - not syncing: sysrq triggered crash
......
[ 172.406423] mtdoops: not ready 34, 35 (erase immediately)
[ 172.432285] mtdoops: ready 34, 35
[ 172.435633] Rebooting in 10 seconds..
Signed-off-by: Ray Zhang <sgzhang@google.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20221010045549.2221965-4-sgzhang@google.com
Preparing for next patch with minimal code difference, add mtdoops_erase
function and move mtdoops_inc_counter to after it, with no functional
change.
Signed-off-by: Ray Zhang <sgzhang@google.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20221010045549.2221965-3-sgzhang@google.com
To comply with latest kernel code requirement, change printk() to
counterpart pr_ functions in mtdoops driver:
- change printk(INFO) to pr_info()
- change printk(DEBUG) to pr_debug()
- change printk(WARNING) to pr_warn()
- change printk(ERR) to pr_err()
Note that only if dynamic debugging is enabled or DEBUG is defined,
printk(KERN_DEBUG) and pr_debug() are equivalent; Otherwise pr_debug()
is no-op, causing different behavior.
Signed-off-by: Ray Zhang <sgzhang@google.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20221010045549.2221965-2-sgzhang@google.com
So far this feature was limited to the top-level "nvmem-cells" node.
There are multiple parsers creating partitions and subpartitions
dynamically. Extend that code to handle them too.
This allows finding partition-* node for every MTD (sub)partition.
Random example:
partitions {
compatible = "brcm,bcm947xx-cfe-partitions";
partition-firmware {
compatible = "brcm,trx";
partition-loader {
};
};
};
Cc: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20221004083710.27704-2-zajec5@gmail.com
OMAP2 OneNAND driver uses gpmc_omap_onenand_set_timings() provided by
OMAP_GPMC driver, so the latter cannot be module if OneNAND driver is
built-in:
/usr/bin/arm-linux-gnueabi-ld: drivers/mtd/nand/onenand/onenand_omap2.o: in function `omap2_onenand_probe':
onenand_omap2.c:(.text+0x520): undefined reference to `gpmc_omap_onenand_set_timings'
The OMAP_GPMC is also a runtime dependency.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 854fd9209b ("memory: omap-gpmc: Allow building as a module")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20221107091520.127053-1-krzysztof.kozlowski@linaro.org
The compiler is not smart enough to notice that it's impossible for
them to be actually used uninitialized. Which exact variables trip
here varies depending on random surrounding code; none triggered in
6.1-rc1 but 6.1-rc2 fails on three of these five, despite variables
declared in the very same line having identical flow.
Signed-off-by: Adam Borowski <kilobyte@angband.pl>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20221024092026.42123-1-kilobyte@angband.pl
With use_codeword_fixup enabled, any return from
mtd_device_parse_register gets overwritten. Aside from the clear bug, this
is also problematic as a parser can EPROBE_DEFER and because this is not
correctly handled, the nand is never rescanned later in the bootup
process.
An example of this problem is when smem requires additional time to be
probed and nandc use qcomsmempart as parser. Parser will return
EPROBE_DEFER but in the current code this ret gets overwritten by
qcom_nand_host_parse_boot_partitions and qcom_nand_host_init_and_register
return 0.
Correctly handle the return code from mtd_device_parse_register so that
any error from this function is not ignored.
Fixes: 862bdedd7f ("mtd: nand: raw: qcom_nandc: add support for unprotected spare data pages")
Cc: stable@vger.kernel.org # v6.0+
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20221021165304.19991-1-ansuelsmth@gmail.com
Add an error message when failing to exit the 4-byte address mode. Do not
stop the execution and go through the spi_nor_soft_reset() method if used,
in the hope that the flash will default to 3-byte address mode after the
reset.
Suggested-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220728030159.68680-1-tudor.ambarus@microchip.com
We track in the core the internal address mode of the flash. Stop using
hardcoded values for the number of bytes of address and use
nor->addr_nbytes and nor->params->addr_mode_nbytes instead.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20220728041451.85559-3-tudor.ambarus@microchip.com
We track in the core the internal address mode of the flash. Stop using
hardcoded values for the number of bytes of address and use
nor->addr_nbytes and nor->params->addr_mode_nbytes instead.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Link: https://lore.kernel.org/r/20220728041451.85559-2-tudor.ambarus@microchip.com
Read, Page Program, and Sector Erase settings are done in SFDP so we can
remove NO_SFDP_FLAGS from s28hs512t info. Since the default_init() is no
longer called after removing NO_SFDP_FLAGS, the initialization in the
default_init() is moved to late_init().
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/12e468992f5d0cbd474abff3203100cc8163d4e5.1661915569.git.Takahiro.Kuwano@infineon.com
Add support for spi-nor flash reset via GPIO controller by reading the
reset-gpio property. If there is a valid GPIO specifier then reset will
be performed by asserting and deasserting the GPIO using gpiod APIs
otherwise it will not perform any operation.
Signed-off-by: Sai Krishna Potthuri <sai.krishna.potthuri@amd.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220908064428.2962-3-sai.krishna.potthuri@amd.com
There is some code in the parser that tries to read 0x8000
bytes into a block to "read in the middle" of the block. Well
that only works if the block is also 0x10000 bytes all the time,
else we get these parse errors as we reach the end of the flash:
spi-nor spi0.0: mx25l1606e (2048 Kbytes)
mtd_read error while parsing (offset: 0x200000): -22
mtd_read error while parsing (offset: 0x201000): -22
(...)
Fix the code to do what I think was intended.
Cc: stable@vger.kernel.org
Fixes: f0501e81fb ("mtd: bcm47xxpart: alternative MAGIC for board_data partition")
Cc: Rafał Miłecki <zajec5@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20221018091129.280026-1-linus.walleij@linaro.org
Winbond uses 3 bytes to identify flash: vendor_id, dev_id_0, dev_id_1,
but current driver uses only first 2 bytes of it for devices
identification. As result Winbond W25N02KV flash (id_bytes: EF, AA, 22)
is identified as W25N01GV (id_bytes: EF, AA, 21).
Fix this by adding missed identification bytes.
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20221010105110.446674-1-mikhail.kshevetskiy@iopsys.eu
NO_IRQ is used to check the return of irq_of_parse_and_map().
On some architecture NO_IRQ is 0, on other architectures it is -1.
irq_of_parse_and_map() returns 0 on error, independent of NO_IRQ.
So use 0 instead of using NO_IRQ.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/4e3ca3e0077ea124ea210c312e6e620f0f9e8bca.1665034065.git.christophe.leroy@csgroup.eu
Originally the absence of the marvell,nand-keep-config property caused
the setup_data_interface function to be provided. However when
setup_data_interface was moved into nand_controller_ops the logic was
unintentionally inverted. Update the logic so that only if the
marvell,nand-keep-config property is present the bootloader NAND config
kept.
Cc: stable@vger.kernel.org
Fixes: 7a08dbaedd ("mtd: rawnand: Move ->setup_data_interface() to nand_controller_ops")
Signed-off-by: Tony O'Brien <tony.obrien@alliedtelesis.co.nz>
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220927024728.28447-1-chris.packham@alliedtelesis.co.nz
The pm_runtime_enable will increase power disable depth. Thus
a pairing decrement is needed on the error handling path to
keep it balanced according to context.
Cc: stable@vger.kernel.org
Fixes: d7d9f8ec77 ("mtd: rawnand: add NVIDIA Tegra NAND Flash controller driver")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220926084456.98160-1-zhangqilong3@huawei.com
The 'chip_np' returned by of_get_next_child() with refcount decremented,
of_node_put() need be called in error path to decrease the refcount.
Fixes: bfc618fcc3 ("mtd: rawnand: intel: Read the chip-select line from the correct OF node")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220924131010.957117-1-yangyingliang@huawei.com
The Intel SPI-NOR controller does not support the 4-byte address opcode
so ->set_4byte_addr_mode() ends up returning -ENOTSUPP and the SPI flash
chip probe fail like this:
[ 12.291082] spi-nor: probe of spi0.0 failed with error -524
Whereas previously before commit 08412e72af ("mtd: spi-nor: core:
Return error code from set_4byte_addr_mode()") it worked just fine.
Fix this by ignoring -ENOTSUPP in spi_nor_init().
Fixes: 08412e72af ("mtd: spi-nor: core: Return error code from set_4byte_addr_mode()")
Cc: stable@vger.kernel.org
Reported-by: Hongyu Ning <hongyu.ning@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Acked-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220923093441.3178-1-mika.westerberg@linux.intel.com
-----BEGIN PGP SIGNATURE-----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=M+mV
-----END PGP SIGNATURE-----
Merge tag 'random-6.1-rc1-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/crng/random
Pull more random number generator updates from Jason Donenfeld:
"This time with some large scale treewide cleanups.
The intent of this pull is to clean up the way callers fetch random
integers. The current rules for doing this right are:
- If you want a secure or an insecure random u64, use get_random_u64()
- If you want a secure or an insecure random u32, use get_random_u32()
The old function prandom_u32() has been deprecated for a while
now and is just a wrapper around get_random_u32(). Same for
get_random_int().
- If you want a secure or an insecure random u16, use get_random_u16()
- If you want a secure or an insecure random u8, use get_random_u8()
- If you want secure or insecure random bytes, use get_random_bytes().
The old function prandom_bytes() has been deprecated for a while
now and has long been a wrapper around get_random_bytes()
- If you want a non-uniform random u32, u16, or u8 bounded by a
certain open interval maximum, use prandom_u32_max()
I say "non-uniform", because it doesn't do any rejection sampling
or divisions. Hence, it stays within the prandom_*() namespace, not
the get_random_*() namespace.
I'm currently investigating a "uniform" function for 6.2. We'll see
what comes of that.
By applying these rules uniformly, we get several benefits:
- By using prandom_u32_max() with an upper-bound that the compiler
can prove at compile-time is ≤65536 or ≤256, internally
get_random_u16() or get_random_u8() is used, which wastes fewer
batched random bytes, and hence has higher throughput.
- By using prandom_u32_max() instead of %, when the upper-bound is
not a constant, division is still avoided, because
prandom_u32_max() uses a faster multiplication-based trick instead.
- By using get_random_u16() or get_random_u8() in cases where the
return value is intended to indeed be a u16 or a u8, we waste fewer
batched random bytes, and hence have higher throughput.
This series was originally done by hand while I was on an airplane
without Internet. Later, Kees and I worked on retroactively figuring
out what could be done with Coccinelle and what had to be done
manually, and then we split things up based on that.
So while this touches a lot of files, the actual amount of code that's
hand fiddled is comfortably small"
* tag 'random-6.1-rc1-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/crng/random:
prandom: remove unused functions
treewide: use get_random_bytes() when possible
treewide: use get_random_u32() when possible
treewide: use get_random_{u8,u16}() when possible, part 2
treewide: use get_random_{u8,u16}() when possible, part 1
treewide: use prandom_u32_max() when possible, part 2
treewide: use prandom_u32_max() when possible, part 1
UBI:
- Use bitmap API to allocate bitmaps
- New attach mode, disable_fm, to attach without fastmap
- Fixes for various typos in comments
UBIFS:
- Fix for a deadlock when setting xattrs for encrypted file
- Fix for an assertion failures when truncating encrypted files
- Fixes for various typos in comments
-----BEGIN PGP SIGNATURE-----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=UVHq
-----END PGP SIGNATURE-----
Merge tag 'for-linus-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs
Pull UBI and UBIFS updates from Richard Weinberger:
"UBI:
- Use bitmap API to allocate bitmaps
- New attach mode, disable_fm, to attach without fastmap
- Fixes for various typos in comments
UBIFS:
- Fix for a deadlock when setting xattrs for encrypted file
- Fix for an assertion failures when truncating encrypted files
- Fixes for various typos in comments"
* tag 'for-linus-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs:
ubi: fastmap: Add fastmap control support for 'UBI_IOCATT' ioctl
ubi: fastmap: Use the bitmap API to allocate bitmaps
ubifs: Fix AA deadlock when setting xattr for encrypted file
ubifs: Fix UBIFS ro fail due to truncate in the encrypted directory
mtd: ubi: drop unexpected word 'a' in comments
ubi: block: Fix typos in comments
ubi: fastmap: Fix typo in comments
ubi: Fix repeated words in comments
ubi: ubi-media.h: Fix comment typo
ubi: block: Remove in vain semicolon
ubifs: Fix ubifs_check_dir_empty() kernel-doc comment
The prandom_bytes() function has been a deprecated inline wrapper around
get_random_bytes() for several releases now, and compiles down to the
exact same code. Replace the deprecated wrapper with a direct call to
the real function. This was done as a basic find and replace.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Yury Norov <yury.norov@gmail.com>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu> # powerpc
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Rather than truncate a 32-bit value to a 16-bit value or an 8-bit value,
simply use the get_random_{u8,u16}() functions, which are faster than
wasting the additional bytes from a 32-bit value. This was done by hand,
identifying all of the places where one of the random integer functions
was used in a non-32-bit context.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Yury Norov <yury.norov@gmail.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Heiko Carstens <hca@linux.ibm.com> # for s390
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Rather than incurring a division or requesting too many random bytes for
the given range, use the prandom_u32_max() function, which only takes
the minimum required bytes from the RNG and avoids divisions. This was
done mechanically with this coccinelle script:
@basic@
expression E;
type T;
identifier get_random_u32 =~ "get_random_int|prandom_u32|get_random_u32";
typedef u64;
@@
(
- ((T)get_random_u32() % (E))
+ prandom_u32_max(E)
|
- ((T)get_random_u32() & ((E) - 1))
+ prandom_u32_max(E * XXX_MAKE_SURE_E_IS_POW2)
|
- ((u64)(E) * get_random_u32() >> 32)
+ prandom_u32_max(E)
|
- ((T)get_random_u32() & ~PAGE_MASK)
+ prandom_u32_max(PAGE_SIZE)
)
@multi_line@
identifier get_random_u32 =~ "get_random_int|prandom_u32|get_random_u32";
identifier RAND;
expression E;
@@
- RAND = get_random_u32();
... when != RAND
- RAND %= (E);
+ RAND = prandom_u32_max(E);
// Find a potential literal
@literal_mask@
expression LITERAL;
type T;
identifier get_random_u32 =~ "get_random_int|prandom_u32|get_random_u32";
position p;
@@
((T)get_random_u32()@p & (LITERAL))
// Add one to the literal.
@script:python add_one@
literal << literal_mask.LITERAL;
RESULT;
@@
value = None
if literal.startswith('0x'):
value = int(literal, 16)
elif literal[0] in '123456789':
value = int(literal, 10)
if value is None:
print("I don't know how to handle %s" % (literal))
cocci.include_match(False)
elif value == 2**32 - 1 or value == 2**31 - 1 or value == 2**24 - 1 or value == 2**16 - 1 or value == 2**8 - 1:
print("Skipping 0x%x for cleanup elsewhere" % (value))
cocci.include_match(False)
elif value & (value + 1) != 0:
print("Skipping 0x%x because it's not a power of two minus one" % (value))
cocci.include_match(False)
elif literal.startswith('0x'):
coccinelle.RESULT = cocci.make_expr("0x%x" % (value + 1))
else:
coccinelle.RESULT = cocci.make_expr("%d" % (value + 1))
// Replace the literal mask with the calculated result.
@plus_one@
expression literal_mask.LITERAL;
position literal_mask.p;
expression add_one.RESULT;
identifier FUNC;
@@
- (FUNC()@p & (LITERAL))
+ prandom_u32_max(RESULT)
@collapse_ret@
type T;
identifier VAR;
expression E;
@@
{
- T VAR;
- VAR = (E);
- return VAR;
+ return E;
}
@drop_var@
type T;
identifier VAR;
@@
{
- T VAR;
... when != VAR
}
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Yury Norov <yury.norov@gmail.com>
Reviewed-by: KP Singh <kpsingh@kernel.org>
Reviewed-by: Jan Kara <jack@suse.cz> # for ext4 and sbitmap
Reviewed-by: Christoph Böhmwalder <christoph.boehmwalder@linbit.com> # for drbd
Acked-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Heiko Carstens <hca@linux.ibm.com> # for s390
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # for mmc
Acked-by: Darrick J. Wong <djwong@kernel.org> # for xfs
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Here is the large set of char/misc and other small driver subsystem
changes for 6.1-rc1. Loads of different things in here:
- IIO driver updates, additions, and changes. Probably the largest
part of the diffstat
- habanalabs driver update with support for new hardware and features,
the second largest part of the diff.
- fpga subsystem driver updates and additions
- mhi subsystem updates
- Coresight driver updates
- gnss subsystem updates
- extcon driver updates
- icc subsystem updates
- fsi subsystem updates
- nvmem subsystem and driver updates
- misc driver updates
- speakup driver additions for new features
- lots of tiny driver updates and cleanups
All of these have been in the linux-next tree for a while with no
reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCY0GQmA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylyVQCeNJjZ3hy+Wz8WkPSY+NkehuIhyCIAnjXMOJP8
5G/JQ+rpcclr7VOXlS66
=zVkU
-----END PGP SIGNATURE-----
Merge tag 'char-misc-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc and other driver updates from Greg KH:
"Here is the large set of char/misc and other small driver subsystem
changes for 6.1-rc1. Loads of different things in here:
- IIO driver updates, additions, and changes. Probably the largest
part of the diffstat
- habanalabs driver update with support for new hardware and
features, the second largest part of the diff.
- fpga subsystem driver updates and additions
- mhi subsystem updates
- Coresight driver updates
- gnss subsystem updates
- extcon driver updates
- icc subsystem updates
- fsi subsystem updates
- nvmem subsystem and driver updates
- misc driver updates
- speakup driver additions for new features
- lots of tiny driver updates and cleanups
All of these have been in the linux-next tree for a while with no
reported issues"
* tag 'char-misc-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (411 commits)
w1: Split memcpy() of struct cn_msg flexible array
spmi: pmic-arb: increase SPMI transaction timeout delay
spmi: pmic-arb: block access for invalid PMIC arbiter v5 SPMI writes
spmi: pmic-arb: correct duplicate APID to PPID mapping logic
spmi: pmic-arb: add support to dispatch interrupt based on IRQ status
spmi: pmic-arb: check apid against limits before calling irq handler
spmi: pmic-arb: do not ack and clear peripheral interrupts in cleanup_irq
spmi: pmic-arb: handle spurious interrupt
spmi: pmic-arb: add a print in cleanup_irq
drivers: spmi: Directly use ida_alloc()/free()
MAINTAINERS: add TI ECAP driver info
counter: ti-ecap-capture: capture driver support for ECAP
Documentation: ABI: sysfs-bus-counter: add frequency & num_overflows items
dt-bindings: counter: add ti,am62-ecap-capture.yaml
counter: Introduce the COUNTER_COMP_ARRAY component type
counter: Consolidate Counter extension sysfs attribute creation
counter: Introduce the Count capture component
counter: 104-quad-8: Add Signal polarity component
counter: Introduce the Signal polarity component
counter: interrupt-cnt: Implement watch_validate callback
...
* mtdchar: add MEMREAD ioctl
* Add ECC error accounting for each read request
* always initialize 'stats' in struct mtd_oob_ops
* Track maximum number of bitflips for each read request
* Fix repeated word in comment
* Move from strlcpy with unused retval to strscpy
* Fix a typo in a comment
* Add binding for U-Boot bootloader partitions
MTD device drivers changes:
* FTL: use container_of() rather than cast
* docg3:
- Use correct function names in comment blocks
- Check the return value of devm_ioremap() in the probe
* physmap-core: Fix NULL pointer dereferencing in of_select_probe_type()
* parsers: add Broadcom's U-Boot parser
Raw NAND core changes:
* Replace of_gpio_named_count() by gpiod_count()
- Remove misguided comment of nand_get_device()
- bbt: Use the bitmap API to allocate bitmaps
Raw NAND controller drivers changes:
* Meson:
- Stop supporting legacy clocks
- Refine resource getting in probe
- Convert bindings to yaml
- Fix clock handling and update the bindings accordingly
- Fix bit map use in meson_nfc_ecc_correct()
* bcm47xx:
- Fix spelling typo in comment
* STM32 FMC2:
- Switch to using devm_fwnode_gpiod_get()
- Fix dma_map_sg error check
* Cadence:
- Remove an unneeded result variable
* Marvell:
- Fix error handle regarding dma_map_sg
* Orion:
- Use devm_clk_get_optional()
* Cafe:
- Use correct function name in comment block
* Atmel:
- Unmap streaming DMA mappings
* Arasan:
- Stop using 0 as NULL pointer
* GPMI:
- Fix typo 'the the' in comment
* BRCM:
- Add individual glue driver selection
- Move Kconfig to driver folder
* FSL: Fix none ECC mode
* Intel:
- Use devm_platform_ioremap_resource_byname()
- Remove unused clk_rate member from struct ebu_nand
- Remove unused nand_pa member from ebu_nand_cs
- Don't re-define NAND_DATA_IFACE_CHECK_ONLY
- Remove undocumented compatible string
- Fix compatible string in the bindings
- Read the chip-select line from the correct OF node
- Fix maximum chip select value in the bindings
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmNAPlUACgkQJWrqGEe9
VoTQogf/VPcMpDXORmgCm0HldghXsY2WqY92xUCNDEtREUmqLe+mEVuXlucWQdeM
tthHNDhLIJQKDfmGdJiOBOqAZ5D6tjT+ZjTySOGP7TH2gzd5XmGGhFZlblioqryn
oqE2XmPs72hKaFJhcC00Y/DFeaD/EsDolyLgwl9s6hI/JGPLcRFa8Z4gjRkWW8B9
NZEk5mB1AVm2MVjXF0OkT/Pm/FtFQ1HpprV4qhG2ZOHcL1GeDrGddNCZIf3vXgKY
PXHCdjhej+zusHxVsYgkH0ju3n7OYTuxctLPbmK7Gqi3QeBj1SbpZWHEjyPrerFu
jj8W8OXErxNQN49jngnbUa0ZKwuwag==
=6/gy
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD updates from Miquel Raynal:
"Core MTD changes:
- mtdchar: add MEMREAD ioctl
- Add ECC error accounting for each read request
- always initialize 'stats' in struct mtd_oob_ops
- Track maximum number of bitflips for each read request
- Fix repeated word in comment
- Move from strlcpy with unused retval to strscpy
- Fix a typo in a comment
- Add binding for U-Boot bootloader partitions
MTD device drivers changes:
- FTL: use container_of() rather than cast
- docg3:
- Use correct function names in comment blocks
- Check the return value of devm_ioremap() in the probe
- physmap-core: Fix NULL pointer dereferencing in
of_select_probe_type()
- parsers: add Broadcom's U-Boot parser
Raw NAND core changes:
- Replace of_gpio_named_count() by gpiod_count()
- Remove misguided comment of nand_get_device()
- bbt: Use the bitmap API to allocate bitmaps
Raw NAND controller drivers changes:
- Meson:
- Stop supporting legacy clocks
- Refine resource getting in probe
- Convert bindings to yaml
- Fix clock handling and update the bindings accordingly
- Fix bit map use in meson_nfc_ecc_correct()
- bcm47xx:
- Fix spelling typo in comment
- STM32 FMC2:
- Switch to using devm_fwnode_gpiod_get()
- Fix dma_map_sg error check
- Cadence:
- Remove an unneeded result variable
- Marvell:
- Fix error handle regarding dma_map_sg
- Orion:
- Use devm_clk_get_optional()
- Cafe:
- Use correct function name in comment block
- Atmel:
- Unmap streaming DMA mappings
- Arasan:
- Stop using 0 as NULL pointer
- GPMI:
- Fix typo 'the the' in comment
- BRCM:
- Add individual glue driver selection
- Move Kconfig to driver folder
- FSL: Fix none ECC mode
- Intel:
- Use devm_platform_ioremap_resource_byname()
- Remove unused clk_rate member from struct ebu_nand
- Remove unused nand_pa member from ebu_nand_cs
- Don't re-define NAND_DATA_IFACE_CHECK_ONLY
- Remove undocumented compatible string
- Fix compatible string in the bindings
- Read the chip-select line from the correct OF node
- Fix maximum chip select value in the bindings"
* tag 'mtd/for-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (43 commits)
mtd: rawnand: meson: stop supporting legacy clocks
dt-bindings: nand: meson: convert txt to yaml
mtd: rawnand: meson: refine resource getting in probe
mtd: rawnand: meson: fix the clock
dt-bindings: nand: meson: fix meson nfc clock
mtd: rawnand: bcm47xx: fix spelling typo in comment
mtd: rawnand: stm32_fmc2: switch to using devm_fwnode_gpiod_get()
mtd: rawnand: cadence: Remove an unneeded result variable
mtd: rawnand: Replace of_gpio_named_count() by gpiod_count()
mtd: rawnand: marvell: Fix error handle regarding dma_map_sg
mtd: rawnand: stm32_fmc2: Fix dma_map_sg error check
mtd: rawnand: remove misguided comment of nand_get_device()
mtd: rawnand: orion: Use devm_clk_get_optional()
mtd: rawnand: cafe: Use correct function name in comment block
mtd: rawnand: atmel: Unmap streaming DMA mappings
mtd: rawnand: meson: fix bit map use in meson_nfc_ecc_correct()
mtd: rawnand: arasan: stop using 0 as NULL pointer
mtd: rawnand: gpmi: Fix typo 'the the' in comment
mtd: rawnand: brcmnand: Add individual glue driver selection
mtd: rawnand: brcmnand: Move Kconfig to driver folder
...
* Replace of_gpio_named_count() by gpiod_count()
- Remove misguided comment of nand_get_device()
- bbt: Use the bitmap API to allocate bitmaps
Raw NAND controller drivers changes:
* Meson:
- Stop supporting legacy clocks
- Refine resource getting in probe
- Convert bindings to yaml
- Fix clock handling and update the bindings accordingly
- Fix bit map use in meson_nfc_ecc_correct()
* bcm47xx:
- Fix spelling typo in comment
* STM32 FMC2:
- Switch to using devm_fwnode_gpiod_get()
- Fix dma_map_sg error check
* Cadence:
- Remove an unneeded result variable
* Marvell:
- Fix error handle regarding dma_map_sg
* Orion:
- Use devm_clk_get_optional()
* Cafe:
- Use correct function name in comment block
* Atmel:
- Unmap streaming DMA mappings
* Arasan:
- Stop using 0 as NULL pointer
* GPMI:
- Fix typo 'the the' in comment
* BRCM:
- Add individual glue driver selection
- Move Kconfig to driver folder
* FSL: Fix none ECC mode
* Intel:
- Use devm_platform_ioremap_resource_byname()
- Remove unused clk_rate member from struct ebu_nand
- Remove unused nand_pa member from ebu_nand_cs
- Don't re-define NAND_DATA_IFACE_CHECK_ONLY
- Remove undocumented compatible string
- Fix compatible string in the bindings
- Read the chip-select line from the correct OF node
- Fix maximum chip select value in the bindings
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmNAOvwACgkQJWrqGEe9
VoRNwQf9EqZu7zW/kWBi7cN9koCk/5YuKeCQi9KJhCf4MC9928BdEy5wwRYPkZPJ
N1rTS4Fdx+nLDpULqcE9KYDSJZM09dGEHN7sFYwJR+zKRpBV5awfDvV8gWZp1Afk
MLtC+AWO1GkJ/5V0Qmw0RX+0rtM9v+QpH25+nvJImBKt7iTfperpBDmO7S7htxhN
xPKLj8A8Ns2LR/JirwHT2DRLwe/1UJwLxNfL/yzyWxekaqmRUNz2rYSQ56ZJAbc4
D9jotFRwdpaMIKkGuruYed2gM7rgbtzSaGLZNYuHzcLMKFocH9vLL7D3EAbovoDL
D1l1saZDYsYpXkVwM4uKPWR/B8lgcg==
=DvSB
-----END PGP SIGNATURE-----
Merge tag 'nand/for-6.1' into mtd/next
Raw NAND core changes:
* Replace of_gpio_named_count() by gpiod_count()
- Remove misguided comment of nand_get_device()
- bbt: Use the bitmap API to allocate bitmaps
Raw NAND controller drivers changes:
* Meson:
- Stop supporting legacy clocks
- Refine resource getting in probe
- Convert bindings to yaml
- Fix clock handling and update the bindings accordingly
- Fix bit map use in meson_nfc_ecc_correct()
* bcm47xx:
- Fix spelling typo in comment
* STM32 FMC2:
- Switch to using devm_fwnode_gpiod_get()
- Fix dma_map_sg error check
* Cadence:
- Remove an unneeded result variable
* Marvell:
- Fix error handle regarding dma_map_sg
* Orion:
- Use devm_clk_get_optional()
* Cafe:
- Use correct function name in comment block
* Atmel:
- Unmap streaming DMA mappings
* Arasan:
- Stop using 0 as NULL pointer
* GPMI:
- Fix typo 'the the' in comment
* BRCM:
- Add individual glue driver selection
- Move Kconfig to driver folder
* FSL: Fix none ECC mode
* Intel:
- Use devm_platform_ioremap_resource_byname()
- Remove unused clk_rate member from struct ebu_nand
- Remove unused nand_pa member from ebu_nand_cs
- Don't re-define NAND_DATA_IFACE_CHECK_ONLY
- Remove undocumented compatible string
- Fix compatible string in the bindings
- Read the chip-select line from the correct OF node
- Fix maximum chip select value in the bindings
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The drivers branch for 6.1 is a bit larger than for most releases. Most
of the changes come from SoC maintainers for the drivers/soc subsystem:
- A new driver for error handling on the NVIDIA Tegra
'control backbone' bus.
- A new driver for Qualcomm LLCC/DDR bandwidth measurement
- New Rockchip rv1126 and rk3588 power domain drivers
- DT binding updates for memory controllers, older Rockchip
SoCs, various Mediatek devices, Qualcomm SCM firmware
- Minor updates to Hisilicon LPC bus, the Allwinner SRAM
driver, the Apple rtkit firmware driver, Tegra firmware
- Minor updates for SoC drivers (Samsung, Mediatek, Renesas,
Tegra, Qualcomm, Broadcom, NXP, ...)
There are also some separate subsystem with downstream maintainers that
merge updates this way:
- Various updates and new drivers in the memory controller
subsystem for Mediatek and Broadcom SoCs
- Small set of changes in preparation to add support for FF-A
v1.1 specification later, in the Arm FF-A firmware subsystem
- debugfs support in the PSCI firmware subsystem
-----BEGIN PGP SIGNATURE-----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=WX9J
-----END PGP SIGNATURE-----
Merge tag 'arm-drivers-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM driver updates from Arnd Bergmann:
"The drivers branch for 6.1 is a bit larger than for most releases.
Most of the changes come from SoC maintainers for the drivers/soc
subsystem:
- A new driver for error handling on the NVIDIA Tegra 'control
backbone' bus.
- A new driver for Qualcomm LLCC/DDR bandwidth measurement
- New Rockchip rv1126 and rk3588 power domain drivers
- DT binding updates for memory controllers, older Rockchip SoCs,
various Mediatek devices, Qualcomm SCM firmware
- Minor updates to Hisilicon LPC bus, the Allwinner SRAM driver, the
Apple rtkit firmware driver, Tegra firmware
- Minor updates for SoC drivers (Samsung, Mediatek, Renesas, Tegra,
Qualcomm, Broadcom, NXP, ...)
There are also some separate subsystem with downstream maintainers
that merge updates this way:
- Various updates and new drivers in the memory controller subsystem
for Mediatek and Broadcom SoCs
- Small set of changes in preparation to add support for FF-A v1.1
specification later, in the Arm FF-A firmware subsystem
- debugfs support in the PSCI firmware subsystem"
* tag 'arm-drivers-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (149 commits)
ARM: remove check for CONFIG_DEBUG_LL_SER3
firmware/psci: Add debugfs support to ease debugging
firmware/psci: Print a warning if PSCI doesn't accept PC mode
dt-bindings: memory: snps,dw-umctl2-ddrc: Extend schema with IRQs/resets/clocks props
dt-bindings: memory: snps,dw-umctl2-ddrc: Replace opencoded numbers with macros
dt-bindings: memory: snps,dw-umctl2-ddrc: Use more descriptive device name
dt-bindings: memory: synopsys,ddrc-ecc: Detach Zynq DDRC controller support
soc: sunxi: sram: Add support for the D1 system control
soc: sunxi: sram: Export the LDO control register
soc: sunxi: sram: Save a pointer to the OF match data
soc: sunxi: sram: Return void from the release function
soc: apple: rtkit: Add apple_rtkit_poll
soc: imx: add i.MX93 media blk ctrl driver
soc: imx: add i.MX93 SRC power domain driver
soc: imx: imx8m-blk-ctrl: Use genpd_xlate_onecell
soc: imx: imx8mp-blk-ctrl: handle PCIe PHY resets
soc: imx: imx8m-blk-ctrl: add i.MX8MP VPU blk ctrl
soc: imx: add i.MX8MP HDMI blk ctrl HDCP/HRV_MWR
soc: imx: add icc paths for i.MX8MP hsio/hdmi blk ctrl
soc: imx: add icc paths for i.MX8MP media blk ctrl
...
MTD subsystem API allows interacting with MTD devices (e.g. reading,
writing, handling bad blocks). So far a random driver could get MTD
device only by its name (get_mtd_device_nm()). This change allows
getting them also by a DT node.
This API is required for drivers handling DT defined MTD partitions in a
specific way (e.g. U-Boot (sub)partition with environment variables).
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20220916122100.170016-3-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[1] suggests that fastmap is suitable for large flash devices. Module
parameter 'fm_autoconvert' is a coarse grained switch to enable all
ubi devices to generate fastmap, which may turn on fastmap even for
small flash devices.
This patch imports a new field 'disable_fm' in struct 'ubi_attach_req'
to support following situations by ioctl 'UBI_IOCATT'.
[old functions]
A. Disable 'fm_autoconvert': Disbable fastmap for all ubi devices
B. Enable 'fm_autoconvert': Enable fastmap for all ubi devices
[new function]
C. Enable 'fm_autoconvert', set 'disable_fm' for given device: Don't
create new fastmap and do full scan (existed fastmap will be
destroyed) for the given ubi device.
A simple test case in [2].
[1] http://www.linux-mtd.infradead.org/doc/ubi.html#L_fastmap
[2] https://bugzilla.kernel.org/show_bug.cgi?id=216278
Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Use bitmap_zalloc()/bitmap_free() instead of hand-writing them.
It is less verbose and it improves the semantic.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Zhihao Cheng <chengzhihao1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
there is an unexpected word 'a' in the comments that need to be dropped
file - drivers/mtd/ubi/vmt.c
line - 626,779
* Returns zero if volume is all right and a a negative error code if not.
changed to:
* Returns zero if volume is all right and a negative error code if not.
Signed-off-by: Jiang Jian <jiangjian@cdjrlc.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Various spelling mistakes in comments.
Detected with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: Richard Weinberger <richard@nod.at>
There are a typo(dont't) in comments.
Fix it.
Signed-off-by: Zhang Jiaming <jiaming@nfschina.com>
Reviewed-by: Zhihao Cheng <chengzhihao1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Delete the redundant word 'a'.
Delete the redundant word 'the'.
Signed-off-by: Jilin Yuan <yuanjilin@cdjrlc.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
The double `the' is duplicated in the comment, remove one.
Signed-off-by: Jason Wang <wangborong@cdjrlc.com>
Reviewed-by: Zhihao Cheng <chengzhihao1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Remove the repeated ';' from code, it is not
needed.
Signed-off-by: Li zeming <zeming@nfschina.com>
Reviewed-by: Zhihao Cheng <chengzhihao1@huawei.com>
[rw: Massaged commit message a bit]
Signed-off-by: Richard Weinberger <richard@nod.at>
meson NFC driver only uses common clock interfaces, which triggers kernel test
robot errors when using legacy clocks with HAVE_LEGACY_CLK on.
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Liang Yang <liang.yang@amlogic.com>
[miquel.raynal@bootlin.com: Rephrase the commit log]
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220907080405.28240-6-liang.yang@amlogic.com
simply use devm_platform_ioremap_resource_byname() instead of two steps:
res = platform_get_resource(pdev, IORESOURCE_MEM, 0) and
reg_base = devm_ioremap_resource(dev, res)
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Liang Yang <liang.yang@amlogic.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220907080405.28240-4-liang.yang@amlogic.com
