The devices from the ADAU17X1 family all have a MCLK clock input which
supplies the master clock for the device. The master clock is used as the
input clock for the PLL. Currently the MCLK rate as well as the desired PLL
output frequency need to be supplied by calling snd_soc_dai_set_pll() form
a machine driver.
Add support for specifying the MCLK using the common clock framework. In
addition to that also automatically configure the PLL to a suitable rate
if the master clock was provided using the CCW. This allows to use the
CODEC driver without any special configuration requirements from the
machine driver.
While the PLL output frequency can be configured over a (more or less)
continuous range the narrowness of the range and the other constraints of
the clocking tree usually only result in two output frequencies that will
actually be chosen. One for 44.1kHz based rates and one for 48kHz based
rates, these are the rates that the automatic PLL configuration will use.
For the rare case where a non-standard setup is required a machine driver
can disable the auto-configuration and configure a custom frequency using
the existing mechanisms.
If the common clock framework is not enabled clk_get() will return NULL and
the driver will function as before and the clock rate needs to be
configured manually.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Multiple devices from the ADAU family share the same PLL structure and
configuration register layout. Introduce a new helper module that can be
used to calculated the PLL configuration registers based on a specified
input frequency and the desired output frequency of the PLL.
The ADAU1761/ADAU1781 and ADAU1373 drivers are updated to make use of this
new helper module. But future drivers for additional devices from the ADAU
family are also expected to make use of it.
In anticipation of sharing more infrastructure code between different
devices from the ADAU family the new module is called adau-utils.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The dapm field of the snd_soc_codec struct is eventually going to be
removed, in preparation for this replace all manual access to
codec->dapm with snd_soc_codec_get_dapm().
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
To be able to read back data from the DSP parameter memory the register
range needs to be marked as readable. At the same time we do not want them
to e.g. appear in debugfs output so mark them as precious as well.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The v2 file format of the SigmaDSP takes a more declarative style compared
to the imperative style of the v1 format. In addition some features that are
supported with v2 require the driver to keep state around for the firmware.
This requires a bit of restructuring of both the firmware loader itself and
the drivers making use of the firmware loader.
Instead of loading and executing the firmware in place when the DSP is
configured the firmware is now loaded at driver probe time. This is required
since the new firmware format will in addition to the firmware data itself
contain meta information describing the firmware and its requirements and
capabilities. Those will for example be used to restrict the supported
samplerates advertised by the driver to userspace to the list of samplerates
supported for the firmware.
This only does the restructuring required by the v2 format, but does not
yet add support for the new format itself.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The ADAU1X61 and ADAU1X81 are very similar in the digital domain, but are quite
different in the analog domain. This patch adds support for the common parts of
the ADAU1X61 and ADAU1X81 CODECs.
The patch also restores some of the alphabetical order in the Makfile and
Kconfig.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
