The previous patch addressed a warning but not the cause:
drivers/slimbus/qcom-ctrl.c: In function 'qcom_slim_probe':
drivers/slimbus/qcom-ctrl.c:584:9: error: passing argument 3 of 'dmam_alloc_coherent' from incompatible pointer type [-Werror=incompatible-pointer-types]
There are two things wrong here:
- The naming is very confusing, we now have a member named 'phys'
that doesn't refer to a phys_addr_t but a dma_addr_t. If we needed
a dma address, it should be named 'dma' to avoid confusion, and
to make it less likely that someone passes it into a function that
expects a physical address.
- The dma address is not used at all at this point. It may have been
designed to support DMA in the future, but today it doesn't, so
the only effect right now is to make transfers artificially slower
by using uncached memory instead of cached memory for a temporary
buffer.
This removes the unused structure member and instead changes the code
to call devm_kcalloc(), which matches the usage of the 'base' pointer
as an array of temporary buffers.
Fixes: db809859c8 ("slimbus: qcom: fix incompatible pointer warning")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
One of the pointer passed to dmam_alloc_coherent seems to be
phys_addr_t * instead of dma_addr_t *. This address will be
used by dma apis, so change this to proper type.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Slimbus HW mandates that clock-pause sequence has to be executed
before disabling relevant interface and core clocks.
Runtime-PM's autosuspend feature is used here to enter/exit low
power mode for Qualcomm's Slimbus controller. Autosuspend feature
enables driver to avoid changing power-modes too frequently since
entering clock-pause is an expensive sequence
Signed-off-by: Sagar Dharia <sdharia@codeaurora.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviwed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This controller driver programs manager, interface, and framer
devices for Qualcomm's slimbus HW block.
Manager component currently implements logical address setting,
and messaging interface.
Interface device reports bus synchronization information, and framer
device clocks the bus from the time it's woken up, until clock-pause
is executed by the manager device.
Signed-off-by: Sagar Dharia <sdharia@codeaurora.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviwed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds some common constant defines which are required
for qcom slim controller driver.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviwed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Per SLIMbus specification, a reconfiguration sequence known as
'clock pause' needs to be broadcast over the bus while entering low-
power mode. Clock-pause is initiated by the controller driver.
To exit clock-pause, controller typically wakes up the framer device.
Since wakeup precedure is controller-specific, framework calls it via
controller's function pointer to invoke it.
Signed-off-by: Sagar Dharia <sdharia@codeaurora.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviwed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SLIMbus devices use value-element, and information elements to
control device parameters (e.g. value element is used to represent
gain for codec, information element is used to represent interrupt
status for codec when codec interrupt fires).
Messaging APIs are used to set/get these value and information
elements. SLIMbus specification uses 8-bit "transaction IDs" for
messages where a read-value is anticipated. Framework uses a table
of pointers to store those TIDs and responds back to the caller in
O(1).
Caller can do synchronous and asynchronous reads/writes.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviwed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support to parse slim devices from device tree.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviwed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support to slim controllers in the slim core,
including some utility functions invoked by the controller and
slim device drivers.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviwed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SLIMbus (Serial Low Power Interchip Media Bus) is a specification
developed by MIPI (Mobile Industry Processor Interface) alliance.
SLIMbus is a 2-wire implementation, which is used to communicate with
peripheral components like audio-codec.
SLIMbus uses Time-Division-Multiplexing to accommodate multiple data
channels, and control channel. Control channel has messages to do
device-enumeration, messages to send/receive control-data to/from
SLIMbus devices, messages for port/channel management, and messages to
do bandwidth allocation.
The framework supports multiple instances of the bus (1 controller per
bus), and multiple slave devices per controller.
This patch adds support to basic silmbus core which includes support to
SLIMbus type, slimbus device registeration and some basic data structures.
Signed-off-by: Sagar Dharia <sdharia@codeaurora.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviwed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
