so far vblank interrupt on ironlake is disabled, this would cause
bad gfx performance if userspace calls drm_wait_vblank. This patch
enables vblank interrupt on ironlake and follows vblank get/put
model.
Signed-off-by: Li Peng <peng.li@intel.com>
Acked-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This tries to fix CRT detect loop hang seen on some Ironlake form
factor, to clear up hotplug detect state before taking CRT detect
to make sure next hotplug detect cycle is consistent.
Cc: Stable Team <stable@kernel.org>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This enables possible 36bit address mask on 965G that use physical
address for hw status page.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Original DP mode_valid check didn't take pixel color depth into account,
which made one 1600x900 eDP panel's mode check invalid because of overclock,
but actually this 6bpc panel does can work with x1 lane at 2.7G. This one
trys to take bpp value properly both in mode validation and mode setting.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Many platform support this feature, and it can provide significant
power savings when the reduced refresh rate is low. However, on some
platforms a secondary (reduced) timing is provided but not actually
supported by the hardware. This results in undesirable flicker at
runtime.
So disable the feature by default, but allow users to opt-in to the
reduced clock behavior with a new module parameter, lvds_downclock,
that can be set to 1 to enable the feature.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org> (in principle)
Signed-off-by: Eric Anholt <eric@anholt.net>
On Ironlake, there is an interrupt master control bit. With the bit
disabled before clearing IIR, we do not need to handle extra interrupt
in a loop. This patch removes the loop in Ironlake interrupt handler.
It fixed irq lost issue on some Ironlake platforms.
Cc: Stable Team <stable@kernel.org>
Signed-off-by: Zou Nan hai <Nanhai.zou@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
When we setup buffer for display plane, we'll check any pending
required GPU flush and possible make interruptible wait for flush
complete. But that wait would be most possibly to fail in case of
signals received for X process, which will then fail modeset process
and put display engine in unconsistent state. The result could be
blank screen or CPU hang, and DDX driver would always turn on outputs
DPMS after whatever modeset fails or not.
So this one creates new helper for setup display plane buffer, and
when needing flush using uninterruptible wait for that.
This one should fix bug like https://bugs.freedesktop.org/show_bug.cgi?id=24009.
Also fixing mode switch stress test on Ironlake.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
There exist multiple DDC buses for the SDVO cards with multiple outputs.
When we can't get the EDID by using the select DDC bus, we can try the other
possible DDC bus to see whether the EDID can be obtained.
https://bugs.freedesktop.org/show_bug.cgi?id=23842
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Tested-by: Sebastien Caty <sebastien.caty@mrnf.gouv.qc.ca>
Signed-off-by: Eric Anholt <eric@anholt.net>
For some SDVO cards based on conexant chip, we can't read the EDID if
we don't read the response after issuing SDVO DDC bus switch
command.
From the SDVO spec once when another I2C transaction is finished after
completing the I2C transaction of issuing the bus switch command, it
will be switched back to the SDVO internal state again. So we can't
initiate a new I2C transaction to read the response after issuing the
DDC bus switch command. Instead we should issue DDC bus switch command
and read the response in the same I2C transaction.
https://bugs.freedesktop.org/show_bug.cgi?id=23842https://bugs.freedesktop.org/show_bug.cgi?id=24458https://bugs.freedesktop.org/show_bug.cgi?id=24522https://bugs.freedesktop.org/show_bug.cgi?id=24282
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Tested-by: Sebastien Caty <sebastien.caty@mrnf.gouv.qc.ca>
Signed-off-by: Eric Anholt <eric@anholt.net>
On some boxes the BIOS will report different child device arrays when
the system is booted with/without the dock. In such case the HDMI/DP
port can't be setup correctly. So revert two commits
(fc816655236cd9da162356e96e74c7cfb0834d92/
6e36595a21) that use the child device
parsed from VBT to setup HDMI/DP.
http://bugzilla.kernel.org/show_bug.cgi?id=14854http://bugzilla.kernel.org/show_bug.cgi?id=14860
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Tested-by: Sean Young <sean@mess.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Commit cbda12d77e (drm/i915: implement
new pm ops for i915), among other things, removed the .suspend and
.resume pointers from the struct drm_driver object in i915_drv.c,
which broke resume without KMS on my MSI Wind U100.
Fix this by reverting that part of commit cbda12d77e.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[anholt: added comment explaining when .suspend/.resume matter]
Signed-off-by: Eric Anholt <eric@anholt.net>
Without this fix, some modes couldn't find appropriate clocks.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Tested-by: Matthew Garrett <mjg@redhat.com>
For any given clock we can use the find_pll to get the corresponding DPLL
setting. It is unnecessary to use the find_reduce_pll callback function
to calculate the DPLL parameter for LVDS downclock in order to get the same
divider factor(P) for the normal and downclock.
In theory when the LVDS downclock is supported by LVDS panel, we should get the
same DPLL divider factor(P) for the normal clock and reduced downclock.
If we get the diferent divider factor(P) for normal clock and reduced downclock,
it means that the found downclock is incorrect and should be discarded.
So we should use find_pll callback to calculate the DPLL parameter for the
LVDS reduced downclock as for the normal clock. Then we can do the cleanup
about find_reduced_pll.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
cc: Jesse Barnes <jbarnes@virtuousgeek.org>
cc: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
As we removed TV hotplug, don't check its status ever.
Reviewed-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon/kms: rs600: use correct mask for SW interrupt
gpu/drm/radeon/radeon_irq.c: move a dereference below a NULL test
drm/radeon/radeon_device.c: move a dereference below a NULL test
drm/radeon/radeon_fence.c: move a dereference below the NULL test
drm/radeon/radeon_connectors.c: add a NULL test before dereference
drm/radeon/kms: fix memory leak
drm/kms: Fix &&/|| confusion in drm_fb_helper_connector_parse_command_line()
drm/edid: Fix CVT width/height decode
drm/edid: Skip empty CVT codepoints
drm: remove address mask param for drm_pci_alloc()
drm/radeon/kms: add missing breaks in i2c and ss lookups
drm/radeon/kms: add primary dac adj values table
drm/radeon/kms: fallback to default connector table
drm_pci_alloc() has input of address mask for setting pci dma
mask on the device, which should be properly setup by drm driver.
And leave it as a param for drm_pci_alloc() would cause confusion
or mistake would corrupt the correct dma mask setting, as seen on
intel hw which set wrong dma mask for hw status page. So remove
it from drm_pci_alloc() function.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'drm-intel-next' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel: (23 commits)
drm/i915: remove full registers dump debug
drm/i915: Add DP dpll limit on ironlake and use existing DPLL search function
drm/i915: Select the correct BPC for LVDS on Ironlake
drm/i915: Make the BPC in FDI rx/transcoder be consistent with that in pipeconf on Ironlake
drm/i915: Enable/disable the dithering for LVDS based on VBT setting
drm/i915: Permit pinning whilst the device is 'suspended'
drm/i915: Hold struct mutex whilst pinning power context bo.
drm/i915: fix unused var
drm/i915: Storage class should be before const qualifier
drm/i915: remove render reclock support
drm/i915: Fix RC6 suspend/resume
drm/i915: execbuf2 support
drm/i915: Reload hangcheck timer too for Ironlake
drm/i915: only enable hotplug for detected outputs
drm/i915: Track whether cursor needs physical address in intel_device_info
drm/i915: Implement IS_* macros using static tables
drm/i915: Move PCI IDs into i915 driver
drm/i915: Update LVDS connector status when receiving ACPI LID event
drm/i915: Add MALATA PC-81005 to ACPI LID quirk list
drm/i915: implement new pm ops for i915
...
This one reverts 9e3a6d155e.
As reported by http://bugzilla.kernel.org/show_bug.cgi?id=14485,
this dump will cause hang problem on some machine. If something
really needs this kind of full registers dump, that could be done
within intel-gpu-tools.
Cc: Ben Gamari <bgamari.foss@gmail.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
For some clocks, the old Ironlake DPLL calculator wold give m/n/p
combinations that didn't match the spreadsheet of what HW validation
tests. Instead, use the G4X DPLL calculator, which does a better job
at it.
So we use the intel_g4x_find_best_pll to calculate the DPLL for CRT/HDMI/LVDS
on ironlake. At the same time to consider the dpll setting for display port, we
add the display port DPLL limit on ironlake, which will directly use the
function of intel_find_pll_ironlake_dp to get the corresponding dpll setting.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Select the correct BPC for LVDS on Ironlake. If it is 18-bit LVDS panel,
the BPC will be 6. When it is 24-bit LVDS panel, the BPC will 8.
At the same time the BPC will be 8 when the output device is CRT/HDMI/DP.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Make the BPC in FDI rx/transcoder be consistent with that in pipeconf on Ironlake.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Enable/disable the dithering for LVDS based on VBT setting. On the 965/g4x
platform the dithering flag is defined in LVDS register. And on the ironlake
the dithering flag is defined in pipeconf register.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
As pinning (allocating and binding GTT memory) does not actually invoke
GPU commands, it is safe, and indeed is attempted, during resumption
from suspension:
[drm:intel_init_clock_gating] *ERROR* failed to pin power context: -16
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reported-by: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Cc: stable@kernel.org
Signed-off-by: Eric Anholt <eric@anholt.net>
Hugh found an error path where we were attempting to unref a bo without
holding the struct mutex:
[drm:intel_init_clock_gating] *ERROR* failed to pin power context: -16
------------[ cut here ]------------
WARNING: at drivers/gpu/drm/drm_gem.c:438 drm_gem_object_free+0x20/0x5e()
Hardware name: ESPRIMO Mobile V5505
Modules linked in: snd_pcm_oss snd_mixer_oss snd_seq snd_seq_device
Pid: 3793, comm: s2ram Not tainted 2.6.33-rc2 #4
Call Trace:
[<7815298e>] warn_slowpath_common+0x59/0x6b
[<781529b3>] warn_slowpath_null+0x13/0x18
[<78317c1a>] ? drm_gem_object_free+0x20/0x5e
[<78317c1a>] drm_gem_object_free+0x20/0x5e
[<78317bfa>] ? drm_gem_object_free+0x0/0x5e
[<7829df11>] kref_put+0x38/0x45
[<7833a5f0>] intel_init_clock_gating+0x232/0x271
[<78317bfa>] ? drm_gem_object_free+0x0/0x5e
[<7832c307>] i915_restore_state+0x21a/0x2b3
[<7832379d>] i915_resume+0x3c/0xbb
[<78174fe5>] ? trace_hardirqs_on_caller+0xfc/0x123
[<7831c756>] ? drm_class_resume+0x0/0x3e
[<7831c78d>] drm_class_resume+0x37/0x3e
[<78351e0a>] legacy_resume+0x1e/0x51
[<78351ece>] device_resume+0x91/0xab
[<7831c756>] ? drm_class_resume+0x0/0x3e
[<78352226>] dpm_resume+0x58/0x10f
[<783522fb>] dpm_resume_end+0x1e/0x2c
[<78180f80>] suspend_devices_and_enter+0x61/0x84
[<78180ff8>] enter_state+0x55/0x83
[<7818091c>] state_store+0x94/0xaa
[<7829d09e>] kobj_attr_store+0x1e/0x23
[<782098e0>] sysfs_write_file+0x66/0x99
[<781cd2f0>] vfs_write+0x8a/0x108
[<781cd408>] sys_write+0x3c/0x63
[<78125c10>] sysenter_do_call+0x12/0x36
---[ end trace a343537f29950fda ]---
It is in fact slightly more insiduous that first appears since we are
attempting to not just free the object without the lock, but are trying
to do the whole bo manipulation without holding the lock.
Reported-by: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Signed-off-by: Eric Anholt <eric@anholt.net>
drivers/gpu/drm/i915/i915_dma.c: In function 'i915_driver_load':
drivers/gpu/drm/i915/i915_dma.c:1114: warning: 'll_base' may be used uninitialized in this function
Partly this is because gcc isn't smart enough. But `ll_base' does get used
uninitialised in the DRM_DEBUG() call.
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Eric Anholt <eric@anholt.net>
Cc: Dave Airlie <airlied@linux.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
The C99 specification states in section 6.11.5:
The placement of a storage-class specifier other than at the beginning
of the declaration specifiers in a declaration is an obsolescent
feature.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Eric Anholt <eric@anholt.net>
This code generally fails to adjust the render clock, and when it does,
it conflicts with some other register settings and can cause problems.
So remove this code altogether. I'm reworking it now to do the right
thing, but the only bit it will share is the VBT check for whether
reclocking is supported, so I'm leaving that bit.
Reverts most of 652c393a33 ("add dynamic
clock frequency control"), though for many the regressions showed up
in the later 181a5336d6 ("Fix render
reclock availability detection").
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
We restored RC6 twice on resume, even with modesetting off. Instead,
only restore it once and skip RC6 initialization entirely in non-KMS mode.
Signed-off-by: Andy Lutomirski <luto@mit.edu>
Tested-by: Jeff Chua <jeff.chua.linux@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This patch adds a new execbuf ioctl, execbuf2, for use by clients that
want to control fence register allocation more finely. The buffer
passed in to the new ioctl includes a new relocation type to indicate
whether a given object needs a fence register assigned for the command
buffer in question.
Compatibility with the existing execbuf ioctl is implemented in terms
of the new code, preserving the assumption that fence registers are
required for pre-965 rendering commands.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[ickle: Remove pre-emptive clear_fence_reg()]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Kristian Høgsberg <krh@bitplanet.net>
[anholt: Removed dmesg spam]
Signed-off-by: Eric Anholt <eric@anholt.net>
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (35 commits)
drm/radeon/kms: add definitions for v4 power tables
drm/radeon/kms: never combine LVDS with another encoder
drm/radeon/kms: Check module arguments to be valid V2
drm/radeon/kms: Avoid crash when trying to cleanup uninitialized structure
drm/radeon/kms: add cvt mode if we only have lvds w/h and no edid (v4)
drm/radeon/kms: add 3DC compression support
drm/radeon/kms: allow rendering while no colorbuffer is set on r300
drm/radeon/kms: enable memory clock reading on legacy (V2)
drm/radeon/kms: prevent parallel AtomBIOS calls
drm/radeon/kms: set proper default tv standard
drm/radeon/kms: fix legacy rmx
drm/radeon/kms/atom: fill in proper defines for digital setup
drm/kms: silencing a false positive warning.
drm/mm: fix logic for selection of best fit block
drm/vmwgfx: Use TTM handles instead of SIDs as user-space surface handles.
drm/vmwgfx: Return -ERESTARTSYS when interrupted by a signal.
drm/vmwgfx: Fix unlocked ioctl and add proper access control
drm/radeon: fix build on 64-bit with some compilers.
drivers/gpu: Use kzalloc for allocating only one thing
DRM: Rename clamp variable
...
drm_ioctl is called with the Big Kernel Lock held,
which shows up very high in statistics on vfs_ioctl.
Moving the lock into the drm_ioctl function itself
makes sure we blame the right subsystem and it gets
us one step closer to eliminating the locked version
of fops->ioctl.
Since drm_ioctl does not require the lock itself,
we only need to hold it while calling the specific
handler. The 32 bit conversion handlers do not
interact with any other code, so they don't need
the BKL here either and can just call drm_ioctl.
As a bonus, this cleans up all the other users
of drm_ioctl which now no longer have to find
the inode or call lock_kernel.
[airlied: squashed the non-driver bits
of the second patch in here, this provides
the flag for drivers to use to select unlocked
ioctls - but doesn't modify any drivers].
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: David Airlie <airlied@linux.ie>
Cc: dri-devel@lists.sourceforge.net
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Make sure hangcheck timer won't beat us unexpectedly on Ironlake.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This patch changes around our hotplug enable code a bit to only enable
it for ports we actually detect and initialize. This prevents problems
with stuck or spurious interrupts on outputs that aren't actually wired
up, and is generally more correct.
Fixes FDO bug #23183.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Instead of using the IS_I9XX etc macros that expand to a ton of
comparisons, use new struct intel_device_info to capture the
capabilities of the different chipsets. The drm_i915_private struct
will be initialized to point to the device info that correspond to
the actual device and this way, testing for a specific capability is
just a matter of checking a bit field.
Signed-off-by: Kristian Høgsberg <krh@bitplanet.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
The old include/drm/drm_pciids.h used to be generated from the libdrm
git repo. We don't use that anymore so just use a local list in the
driver like everybody else.
Signed-off-by: Kristian Høgsberg <krh@bitplanet.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
Dirk reports that nothing is displayed on LVDS when using ubuntu 9.1 after
close/reopen the LID. And I also reproduce this issue on another laptop.
After some tests and debug, it seems that it is related with that the
LVDS status is not updated in time in course of suspend/resume.
Now the LID state is used to check whether the LVDS is connected or
disconnected. And when the LID is closed, it means that the LVDS is
disconnected. When it is reopened, it means that the LVDS is connected.
At the same time on some distributions the LID event is also used to put
the system into suspend state. When the LID is closed, the system will enter
the suspend state. When the LID is reopened, the system will be resumed.
In such case when the LID is closed, user-space script will receive the LID
notification event and detect the LVDS as disconnected. Then the system will
enter the suspended state. When the LID is reopened, the system will be
resumed. As the LVDS status is not updated in course of resume, it will cause
that the LVDS connector is marked as unused and disabled. After the resume is
finished,user-space script will try to configure the display mode for LVDS.
But unfortunately as the LVDS status is not updated in time and it is still
marked as disconnected, the LVDS and its corresponding CRTC will be disabled
again in the function of drm_helper_disable_unused_functions after changing
mode for LVDS.
So we had better check and update the status of LVDS connector after receiving
the LID notication event. Then after the system is resumed from suspended
state, we can set the display mode for LVDS correctly.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Reported-by: Dirk Hohndel <hohndel@infradead.org>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
CC: stable@kernel.org
Signed-off-by: Eric Anholt <eric@anholt.net>
The MALATA PC-81005 laptop always reports that the LID status is closed and we
can't use it reliabily for LVDS detection. So add this box into the quirk list.
https://bugs.freedesktop.org/show_bug.cgi?id=25523
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Review-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Hector <hector1987@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
One problem in i915 hibernate with current legacy pci pm ops is
that after we do freeze, we'll be forced to do resume once again,
which re-init some resources and do modesetting again, that is
unnecessary for hibernate. This patch trys to bypass that.
We can't resolve this within legacy pm framework, but can do it
easily with new pm ops. Suspend (S3) process has also been kept
without change.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Checking for the presence of a lid in order to validate whether or not
an LVDS display exists fails on some development platforms that implement
a lid device but allow the LVDS to be disabled. The VBT is correctly
updated, but Linux assumes that an LVDS is still present and lies to
userspace. Remove the lid check and trust the VBT.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
i915_gem_object_unbind had the ordering wrong. The other user,
i915_gem_object_put_fence_reg already has the correct ordering.
Results was usually corrupted pixmaps, especially garbled font glyphs
after a suspend/resume (because this evicts everything).
I'm still waiting for the feedback from the bug-reporters, but
because this obviously fixes a bug (at least for me) I'm already
submitting it.
Bugzilla: http://bugs.freedesktop.org/show_bug.cgi?id=25406
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Eric Anholt <eric@anholt.net>
CC: stable@kernel.org
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (189 commits)
drm/radeon/kms: fix warning about cur_placement being uninitialised.
drm/ttm: Print debug information on memory manager when eviction fails
drm: Add memory manager debug function
drm/radeon/kms: restore surface registers on resume.
drm/radeon/kms/r600/r700: fallback gracefully on ucode failure
drm/ttm: Initialize eviction placement in case the driver callback doesn't
drm/radeon/kms: cleanup structure and module if initialization fails
drm/radeon/kms: actualy set the eviction placements we choose
drm/radeon/kms: Fix NULL ptr dereference
drm/radeon/kms/avivo: add support for new pll selection algo
drm/radeon/kms/avivo: fix some bugs in the display bandwidth setup
drm/radeon/kms: fix return value from fence function.
drm/radeon: Remove tests for -ERESTART from the TTM code.
drm/ttm: Have the TTM code return -ERESTARTSYS instead of -ERESTART.
drm/radeon/kms: Convert radeon to new TTM validation API (V2)
drm/ttm: Rework validation & memory space allocation (V3)
drm: Add search/get functions to get a block in a specific range
drm/radeon/kms: fix avivo tiling regression since radeon object rework
drm/i915: Remove a debugging printk from hangcheck
drm/radeon/kms: make sure i2c id matches
...
