Add rw as bootargs parameter and change from ip=on to ip=dhcp to make the
Marzen board bootargs match other boards from Renesas. No need to be special.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Include R-Car Gen1 product names for Bock-W and Marzen.
The product names are taken from:
Documentation/devicetree/bindings/arm/shmobile.txt
Signed-off-by: Magnus Damm <damm@opensource.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add support for the on-board voltage regulator hooked up to GPIO3_20
on r8a7779 Marzen. The board schematics describes the regulator as U4
TPS2110A. Input wise, U4 has D0 fixed to ground, D1 tied to GPIO3_20
while IN1 is fixed to 3.3V and IN2 is fixed to 1.8V. OUT goes to the
pull-ups for the data pins of SDHI0.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The scif_clk device node is already enabled in r8a7779.dtsi, so there is
no need to update its status again.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Device nodes representing I/O devices should be marked disabled in the
SoC-specific DTS, and overridden by board-specific DTSes where needed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
DU0 uses an externally provided clock, but the corresponding pin isn't
correctly muxed. Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the serial port config to "chosen/stdout-path", which requires
referring to the port by alias.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Name the Pin Function Controller subnodes for SCIF2 and SCIF4 after
their device names, instead of using some arbitrary names that look like
serial port aliases, but differ from the actual aliases.
This avoids conflicts when enabling support for more serial ports later,
either here or in a DT overlay.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Warning (unit_address_vs_reg): Node /memory has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): Node /fixedregulator@0 has a unit name, but no reg property
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Since 16ccaf5bb5 ("pinctrl: sh-pfc: Accept standard function, pins and
groups properties") renesas pfc drivers accept generic "function", "pins"
and "groups" properties.
This patch updates the marzen device tree to use the generic properties.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add and enable the external crystal for the SCIF_CLK and its pinctrl, to
be used by the Baud Rate Generator for External Clock (BRG) on (H)SCIF.
This increases the range and accuracy of supported baud rates.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Convert Marzen to use board-specific serial0 and serial1 instead
of the older shared SoC-specific SCIF index.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Declare the fixed 65MHz pixel clock connected to the DU clock input.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Specify the DU output topology, enable the DU device and configure the
related pins.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a stdout-path property so that automatic console selection works
in the absence of a "console=" parameter on the kernel command line.
Note that we have to keep the "console=" parameter in chosen/bootargs,
as this DTS is shared between legacy and multi-platform.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
No more device needs to be added from platform code when booting the
reference platform, remove the now empty
r8a7779_add_standard_devices_dt() function completely.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Initialise SCIF devices using DT when booting marzen
using multiplatform.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As early printk support is not enabled in the kernel in the
shmobile defconfig it does not make much sense to provide for
it in the default command line.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The external crystal frequency is 31.25 on the Marzen board.
Specify it in the device tree.
Based on work for the Lager board by Laurent Pinchart.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Copy the device nodes from Marzen reference into the Marzen device tree
file. This will allow us to use a single DTS file regardless of kernel
configuration. In case of legacy C board code the device nodes may or
may not be used, but in the multiplatform case all the DT device nodes
will be used.
Based on a similar change for the Lager board by Laurent Pinchart.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
In order to allow usage of the preprocessor in the SoC device tree
sources, switch from /include/ to #include.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This is in preparation for converting the marzen board to
use DT_MACHINE_START.
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
