The 8th NAND partition should be named "NAND.u-boot-env.backup1"
instead of "NAND.u-boot-env". This is to be consistent with other
TI boards as well as u-boot.
CC: Pekon Gupta <pekon@pek-sem.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The I2C3 pins are taken from pads E21 (GPIO6_14) and
F20 (GPIO6_15). Use the right pinmux register and mode.
Also set the I2C3 bus frequency to a safer 400KHz than
3.4Mhz.
CC: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The arm64 interrupt migration code on cpu offline calls
irqchip.irq_set_affinity() with the argument force=true. Originally
this argument had no effect because it was not used by any interrupt
chip driver and there was no semantics defined.
This changed with commit 01f8fa4f01 ("genirq: Allow forcing cpu
affinity of interrupts") which made the force argument useful to route
interrupts to not yet online cpus without checking the target cpu
against the cpu online mask. The following commit ffde1de640
("irqchip: gic: Support forced affinity setting") implemented this for
the GIC interrupt controller.
As a consequence the cpu offline irq migration fails if CPU0 is
offlined, because CPU0 is still set in the affinity mask and the
validation against cpu online mask is skipped to the force argument
being true. The following first_cpu(mask) selection always selects
CPU0 as the target.
Commit 601c942176d8("arm64: use cpu_online_mask when using forced
irq_set_affinity") intended to fix the above mentioned issue but
introduced another issue where affinity can be migrated to a wrong
CPU due to unconditional copy of cpu_online_mask.
As with for arm, solve the issue by calling irq_set_affinity() with
force=false from the CPU offline irq migration code so the GIC driver
validates the affinity mask against CPU online mask and therefore
removes CPU0 from the possible target candidates. Also revert the
changes done in the commit 601c942176 as it's no longer needed.
Tested on Juno platform.
Fixes: 601c942176d8("arm64: use cpu_online_mask when using forced
irq_set_affinity")
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: <stable@vger.kernel.org> # 3.10.x
Signed-off-by: Will Deacon <will.deacon@arm.com>
Another handful of arm64 fixes here:
- A few fixes for real issues found by smatch (after Dan's talk at KS)
- Revert the /proc/cpuinfo changes merged during the merge window.
We've opened a can of worms here, so we need to find out where we
stand before we change this interface.
- Implement KSTK_ESP for compat tasks, otherwise 32-bit Android gets
confused wondering where its [stack] has gone
- Misc fixes (fpsimd context handling, crypto, ...)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABCgAGBQJUBKj4AAoJEC379FI+VC/ZR7wP/jdJ+mK+lqMPg0K2vw8qiGsu
Npq/QBG+mrIcPJZQ/njPBx7Ex7o/8YrhlA4tzuT5sk3Q+P5xgcg6VCneOp4qYmNA
YUuNcWOx1Oufo8FxnmG8nylV9hlNKYiY83/UTlSw4ZdEH9C/CpBb3ihI5XnfJvtE
yRg2DnkW2p4kd0Xp/Ffc9zIEhvquv5ieYEmEXlC0//N/C2AZcbgVBLDBikfxtouM
q6htZZ/jJ4hYTgpY6pL0zl7g/Ct5S2BI07cDKYXg79Sr8GtgbGlAO5LbRb+Ll7LB
Uo3FSN0hhcoHGq+R8QjBKQ/FINSjpywSPIhU1kJESwfyRpLwPdpWM+dy1NNf+/gY
J1xES+jcilYhbb/jQM2E4xsSsID9KmWHEWJ4cDpaDx2DLj2eEX0vfv403ghZ7VSG
yUfTCUFdRLf8HadVlTgsNsS9ckNYRHsxhG+hgMjfM48dkNlkwNQB3wMi8DwUFLY2
BGNKiWbX8LK1qE1Cy81mlsl/P0WzEY8qzswbuOZ7DnN7Rhr1zMMnG5KHYcOyGNPD
BlIKj6DUMgZE49ouExx4sFyO1chmIDgC5R+acHAmEqNS6SvWFrK9eQBjdpob5nff
OBtusJGsSlLmoNQOrzE8funS3fyiuA4Dl/ZsTSyQbVq3IDRCZ1UrCw0+2Py7IMhZ
cWbL9Vbsb9drJbutXrgI
=ibHT
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull more arm64 fixes from Will Deacon:
"Another handful of arm64 fixes here. They address some issues found
by running smatch on the arch code (ignoring the false positives) and
also stop 32-bit Android from losing track of its stack.
There's one additional irq migration fix in the pipeline, but it came
in after I'd tagged and tested this set.
- a few fixes for real issues found by smatch (after Dan's talk at KS)
- revert the /proc/cpuinfo changes merged during the merge window.
We've opened a can of worms here, so we need to find out where we
stand before we change this interface.
- implement KSTK_ESP for compat tasks, otherwise 32-bit Android gets
confused wondering where its [stack] has gone
- misc fixes (fpsimd context handling, crypto, ...)"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
Revert "arm64: cpuinfo: print info for all CPUs"
arm64: fix bug for reloading FPSIMD state after cpu power off
arm64: report correct stack pointer in KSTK_ESP for compat tasks
arm64: Add brackets around user_stack_pointer()
arm64: perf: don't rely on layout of pt_regs when grabbing sp or pc
arm64: ptrace: fix compat reg getter/setter return values
arm64: ptrace: fix compat hardware watchpoint reporting
arm64: Remove unused variable in head.S
arm64/crypto: remove redundant update of data
fc95ca7284 introduces a memset in
kvmppc_alloc_hpt since the general CMA doesn't clear the memory it
allocates.
However, the size argument passed to memset is computed from a signed value
and its signed bit is extended by the cast the compiler is doing. This lead
to extremely large size value when dealing with order value >= 31, and
almost all the memory following the allocated space is cleaned. As a
consequence, the system is panicing and may even fail spawning the kdump
kernel.
This fix makes use of an unsigned value for the memset's size argument to
avoid sign extension. Among this fix, another shift operation which may
lead to signed extended value too is also fixed.
Cc: Alexey Kardashevskiy <aik@ozlabs.ru>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Alexander Graf <agraf@suse.de>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Laurent Dufour <ldufour@linux.vnet.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The quite-recently-added analog-tv-connector bindings say that the
compatible string for composite video connector is
"composite-connector". That string is also used in the omap3-n900.dts
file. However, the connector driver uses "composite-video-connector", so
this has never worked.
While changing the driver's compatible string to "composite-connector"
would be safer, as published DT bindings should not be changed, I'd
rather fix the bindings in this case for two reasons:
* composite-connector is a bit too generic name, as it doesn't even hint
at video.
* it's clear that this has never worked, which means no one has used
those bindings, which should make it safe to change this.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Analogous to commit 8858d88a25
that fixed commit 70b41abc15
"ARM: ux500: move MSP pin control to the device tree"
accidentally activated MSP2, giving rise to a boot scroll
scream as the kernel attempts to probe a driver for it and
fails to obtain DMA channel 14.
For some reason I forgot to fix this on the Snowball. Fix
this up by marking the node disabled again.
Cc: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
commit 0944fe3f4a ("s390/mm: implement software referenced bits")
triggered another paging/storage key corruption. There is an
unhandled invalid->valid pte change where we have to set the real
storage key from the pgste.
When doing paging a guest page might be swapcache or swap and when
faulted in it might be read-only and due to a parallel scan old.
An do_wp_page will make it writeable and young. Due to software
reference tracking this page was invalid and now becomes valid.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: stable@vger.kernel.org # v3.12+
Since 3.12 or more precisely commit 0944fe3f4a ("s390/mm:
implement software referenced bits") guest storage keys get
corrupted during paging. This commit added another valid->invalid
translation for page tables - namely ptep_test_and_clear_young.
We have to transfer the storage key into the pgste in that case.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: stable@vger.kernel.org # v3.12+
It turns out that vendors are relying on the format of /proc/cpuinfo,
and we've even spotted out-of-tree hacks attempting to make it look
identical to the format used by arch/arm/. That means we can't afford to
churn this interface in mainline, so revert the recent reformatting of
the file for arm64 pending discussions on the list to find out what
people actually want.
This reverts commit d7a49086f2.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Now arm64 defers reloading FPSIMD state, but this optimization also
introduces the bug after cpu resume back from low power mode.
The reason is after the cpu has been powered off, s/w need set the
cpu's fpsimd_last_state to NULL so that it will force to reload
FPSIMD state for the thread, otherwise there has the chance to meet
the condition for both the task's fpsimd_state.cpu field contains the
id of the current cpu, and the cpu's fpsimd_last_state per-cpu variable
points to the task's fpsimd_state, so finally kernel will skip to reload
the context during it return back to userland.
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Leo Yan <leoy@marvell.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The explicit NULL pointer check on the timespec argument is only
required for clock_getres but not for clock_gettime.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Currently the loadparm is only supported for CCW IPL. But also for SCSI
IPL it can be specified either on the HMC load panel respectively
z/VM console or via diagnose 308.
So fix this for SCSI and add the required sysfs attributes for reading the
IPL loadparm and for setting the loadparm for re-IPL.
With this patch the following two sysfs attributes are introduced:
- /sys/firmware/ipl/loadparm (for system that have been IPLed from SCSI)
- /sys/firmware/reipl/fcp/loadparm
Because the loadparm is now available for SCSI and CCW it is moved
now from "struct ipl_block_ccw" to the generic "struct ipl_list_hdr".
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
- support highmem on cores with aliasing data cache. Enable highmem on kc705
by default;
- simplify addition of new core variants (no need to modify Kconfig /
Makefiles);
- improve robustness of unaligned access handler and its interaction with
window overflow/underflow exception handlers;
- deprecate atomic and spill registers syscalls;
- clean up Kconfig: remove orphan MATH_EMULATION, sort 'select' statements;
- wire up renameat2 syscall.
Various fixes:
- fix address checks in dma_{alloc,free}_coherent (runtime BUG);
- fix access to THREAD_RA/THREAD_SP/THREAD_DS (debug build breakage);
- fix TLBTEMP_BASE_2 region handling in fast_second_level_miss (runtime
unrecoverable exception);
- fix a6 and a7 handling in fast_syscall_xtensa (runtime userspace register
clobbering);
- fix kernel/user jump out of fast_unaligned (potential runtime unrecoverabl
exception);
- replace termios IOCTL code definitions with constants (userspace build
breakage).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=mAYX
-----END PGP SIGNATURE-----
Merge tag 'xtensa-20140830' of git://github.com/czankel/xtensa-linux
Pull Xtensa updates from Chris Zankel:
"Xtensa improvements for 3.17:
- support highmem on cores with aliasing data cache. Enable highmem
on kc705 by default
- simplify addition of new core variants (no need to modify Kconfig /
Makefiles)
- improve robustness of unaligned access handler and its interaction
with window overflow/underflow exception handlers
- deprecate atomic and spill registers syscalls
- clean up Kconfig: remove orphan MATH_EMULATION, sort 'select'
statements
- wire up renameat2 syscall.
Various fixes:
- fix address checks in dma_{alloc,free}_coherent (runtime BUG)
- fix access to THREAD_RA/THREAD_SP/THREAD_DS (debug build breakage)
- fix TLBTEMP_BASE_2 region handling in fast_second_level_miss
(runtime unrecoverable exception)
- fix a6 and a7 handling in fast_syscall_xtensa (runtime userspace
register clobbering)
- fix kernel/user jump out of fast_unaligned (potential runtime
unrecoverabl exception)
- replace termios IOCTL code definitions with constants (userspace
build breakage)"
* tag 'xtensa-20140830' of git://github.com/czankel/xtensa-linux: (25 commits)
xtensa: deprecate fast_xtensa and fast_spill_registers syscalls
xtensa: don't allow overflow/underflow on unaligned stack
xtensa: fix a6 and a7 handling in fast_syscall_xtensa
xtensa: allow single-stepping through unaligned load/store
xtensa: move invalid unaligned instruction handler closer to its users
xtensa: make fast_unaligned store restartable
xtensa: add double exception fixup handler for fast_unaligned
xtensa: fix kernel/user jump out of fast_unaligned
xtensa: configure kc705 for highmem
xtensa: support highmem in aliasing cache flushing code
xtensa: support aliasing cache in kmap
xtensa: support aliasing cache in k[un]map_atomic
xtensa: implement clear_user_highpage and copy_user_highpage
xtensa: fix TLBTEMP_BASE_2 region handling in fast_second_level_miss
xtensa: allow fixmap and kmap span more than one page table
xtensa: make fixmap region addressing grow with index
xtensa: fix access to THREAD_RA/THREAD_SP/THREAD_DS
xtensa: add renameat2 syscall
xtensa: fix address checks in dma_{alloc,free}_coherent
xtensa: replace IOCTL code definitions with constants
...
unicore32 builds fail with
arch/unicore32/kernel/signal.c: In function ‘setup_frame’:
arch/unicore32/kernel/signal.c:257: error: ‘usig’ undeclared (first use in this function)
arch/unicore32/kernel/signal.c:279: error: ‘usig’ undeclared (first use in this function)
arch/unicore32/kernel/signal.c: In function ‘handle_signal’:
arch/unicore32/kernel/signal.c:306: warning: unused variable ‘tsk’
arch/unicore32/kernel/signal.c: In function ‘do_signal’:
arch/unicore32/kernel/signal.c:376: error: implicit declaration of function ‘get_signsl’
make[1]: *** [arch/unicore32/kernel/signal.o] Error 1
make: *** [arch/unicore32/kernel/signal.o] Error 2
Bisect points to commit 649671c90e ("unicore32: Use get_signal()
signal_setup_done()").
This code never even compiled. Reverting the patch does not work, since
previously used functions no longer exist, so try to fix it up. Compile
tested only.
Fixes: 649671c90e ("unicore32: Use get_signal() signal_setup_done()")
Cc: Richard Weinberger <richard@nod.at>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull ARM fixes from Russell King:
"Various assorted fixes:
- a couple of patches from Mark Rutland to resolve an errata with
Cortex-A15 CPUs.
- fix cpuidle for the CPU part ID changes in the last merge window
- add support for a relocation which ARM binutils is generating in
some circumstances"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 8130/1: cpuidle/cpuidle-big_little: fix reading cpu id part number
ARM: 8129/1: errata: work around Cortex-A15 erratum 830321 using dummy strex
ARM: 8128/1: abort: don't clear the exclusive monitors
ARM: 8127/1: module: add support for R_ARM_TARGET1 relocations
Here's the weekly batch of fixes from arm-soc.
The delta is a largeish negative delta, due to revert of SMP support for Broadcom's
STB SoC -- it was accidentally merged before some issues had been addressed, so they
will make a new attempt for 3.18. I didn't see a need for a full revert of the whole
platform due to this, we're keeping the rest enabled.
The rest is mostly:
* A handful of DT fixes for i.MX (Hummingboard/Cubox-i in particular)
* Some MTD/NAND fixes for OMAP
* Minor DT fixes for shmobile
* Warning fix for UP builds on vexpress/spc
There's also a couple of patches that wires up hwmod on TI's DRA7 SoC
so it can boot. Drivers and the rest had landed for 3.17, and it's small
and isolated so it made sense to pick up now even if it's not a bugfix.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=/AD8
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Here's the weekly batch of fixes from arm-soc.
The delta is a largeish negative delta, due to revert of SMP support
for Broadcom's STB SoC -- it was accidentally merged before some
issues had been addressed, so they will make a new attempt for 3.18.
I didn't see a need for a full revert of the whole platform due to
this, we're keeping the rest enabled.
The rest is mostly:
- a handful of DT fixes for i.MX (Hummingboard/Cubox-i in particular)
- some MTD/NAND fixes for OMAP
- minor DT fixes for shmobile
- warning fix for UP builds on vexpress/spc
There's also a couple of patches that wires up hwmod on TI's DRA7 SoC
so it can boot. Drivers and the rest had landed for 3.17, and it's
small and isolated so it made sense to pick up now even if it's not a
bugfix"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (23 commits)
vexpress/spc: fix a build warning on array bounds
ARM: DRA7: hwmod: Add dra74x and dra72x specific ocp interface lists
ARM: DRA7: Add support for soc_is_dra74x() and soc_is_dra72x() variants
MAINTAINERS: catch special Rockchip code locations
ARM: dts: microsom-ar8035: MDIO pad must be set open drain
ARM: dts: omap54xx-clocks: Fix the l3 and l4 clock rates
ARM: brcmstb: revert SMP support
ARM: OMAP2+: hwmod: Rearm wake-up interrupts for DT when MUSB is idled
ARM: dts: Enable UART wake-up events for beagleboard
ARM: dts: Remove twl6030 clk32g "regulator"
ARM: OMAP2+: omap_device: remove warning that clk alias already exists
ARM: OMAP: fix %d confusingly prefixed with 0x in format string
ARM: dts: DRA7: fix interrupt-cells for GPIO
mtd: nand: omap: Fix 1-bit Hamming code scheme, omap_calculate_ecc()
ARM: dts: omap3430-sdp: Revert to using software ECC for NAND
ARM: OMAP2+: GPMC: Support Software ECC scheme via DT
mtd: nand: omap: Revert to using software ECC by default
ARM: dts: hummingboard/cubox-i: change SPDIF output to be more descriptive
ARM: dts: hummingboard/cubox-i: add USB OC pinctrl configuration
ARM: shmobile: r8a7791: add missing 0x0100 for SDCKCR
...
With ARCH_VEXPRESS_SPC option, kernel build has the following
warning:
arch/arm/mach-vexpress/spc.c: In function ‘ve_spc_clk_init’:
arch/arm/mach-vexpress/spc.c:431:38: warning: array subscript is below array bounds [-Warray-bounds]
struct ve_spc_opp *opps = info->opps[cluster];
^
since 'cluster' maybe '-1' in UP system. This patch does a active
checking to fix this issue.
Signed-off-by: Alex Shi <alex.shi@linaro.org>
Acked-by: Pawel Moll <pawel.moll@arm.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
are OMAP2+ derivative SoCs. This should be low-risk to existing OMAP
platforms.
Basic build, boot, and PM test logs are available here:
http://www.pwsan.com/omap/testlogs/hwmod-a-early-v3.17-rc/20140827194314/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=5ZS8
-----END PGP SIGNATURE-----
Merge tag 'for-v3.17-rc/omap-dra72x-d74x-support-a' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into fixes
Pull "ARM: OMAP2+: DRA72x/DRA74x basic support" from Tony Lindgren:
Add basic subarchitecture support for the DRA72x and DRA74x. These
are OMAP2+ derivative SoCs. This should be low-risk to existing OMAP
platforms.
Basic build, boot, and PM test logs are available here:
http://www.pwsan.com/omap/testlogs/hwmod-a-early-v3.17-rc/20140827194314/
* tag 'for-v3.17-rc/omap-dra72x-d74x-support-a' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending:
ARM: DRA7: hwmod: Add dra74x and dra72x specific ocp interface lists
ARM: DRA7: Add support for soc_is_dra74x() and soc_is_dra72x() variants
Signed-off-by: Olof Johansson <olof@lixom.net>
Pull x86 fixes from Peter Anvin:
"One patch to avoid assigning interrupts we don't actually have on
non-PC platforms, and two patches that addresses bugs in the new
IOAPIC assignment code"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, irq, PCI: Keep IRQ assignment for runtime power management
x86: irq: Fix bug in setting IOAPIC pin attributes
x86: Fix non-PC platform kernel crash on boot due to NULL dereference
Merge patches from Andrew Morton:
"22 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (22 commits)
kexec: purgatory: add clean-up for purgatory directory
Documentation/kdump/kdump.txt: add ARM description
flush_icache_range: export symbol to fix build errors
tools: selftests: fix build issue with make kselftests target
ocfs2: quorum: add a log for node not fenced
ocfs2: o2net: set tcp user timeout to max value
ocfs2: o2net: don't shutdown connection when idle timeout
ocfs2: do not write error flag to user structure we cannot copy from/to
x86/purgatory: use approprate -m64/-32 build flag for arch/x86/purgatory
drivers/rtc/rtc-s5m.c: re-add support for devices without irq specified
xattr: fix check for simultaneous glibc header inclusion
kexec: remove CONFIG_KEXEC dependency on crypto
kexec: create a new config option CONFIG_KEXEC_FILE for new syscall
x86,mm: fix pte_special versus pte_numa
hugetlb_cgroup: use lockdep_assert_held rather than spin_is_locked
mm/zpool: use prefixed module loading
zram: fix incorrect stat with failed_reads
lib: turn CONFIG_STACKTRACE into an actual option.
mm: actually clear pmd_numa before invalidating
memblock, memhotplug: fix wrong type in memblock_find_in_range_node().
...
Without this patch the kexec-purgatory.c and purgatory.ro files are not
removed after make mrproper.
Signed-off-by: Michael Welling <mwelling@ieee.org>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Thomas reported that build of x86_64 kernel was failing for him. He is
using 32bit tool chain.
Problem is that while compiling purgatory, I have not specified -m64
flag. And 32bit tool chain must be assuming -m32 by default.
Following is error message.
(mini) [~/work/linux-2.6] make
scripts/kconfig/conf --silentoldconfig Kconfig
CHK include/config/kernel.release
UPD include/config/kernel.release
CHK include/generated/uapi/linux/version.h
CHK include/generated/utsrelease.h
UPD include/generated/utsrelease.h
CC arch/x86/purgatory/purgatory.o
arch/x86/purgatory/purgatory.c:1:0: error: code model 'large' not supported in
the 32 bit mode
Fix it by explicitly passing appropriate -m64/-m32 build flag for
purgatory.
Reported-by: Thomas Glanzmann <thomas@glanzmann.de>
Tested-by: Thomas Glanzmann <thomas@glanzmann.de>
Suggested-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
New system call depends on crypto. As it did not have a separate config
option, CONFIG_KEXEC was modified to select CRYPTO and CRYPTO_SHA256.
But now previous patch introduced a new config option for new syscall.
So CONFIG_KEXEC does not require crypto. Remove that dependency.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Shaun Ruffell <sruffell@digium.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently new system call kexec_file_load() and all the associated code
compiles if CONFIG_KEXEC=y. But new syscall also compiles purgatory
code which currently uses gcc option -mcmodel=large. This option seems
to be available only gcc 4.4 onwards.
Hiding new functionality behind a new config option will not break
existing users of old gcc. Those who wish to enable new functionality
will require new gcc. Having said that, I am trying to figure out how
can I move away from using -mcmodel=large but that can take a while.
I think there are other advantages of introducing this new config
option. As this option will be enabled only on x86_64, other arches
don't have to compile generic kexec code which will never be used. This
new code selects CRYPTO=y and CRYPTO_SHA256=y. And all other arches had
to do this for CONFIG_KEXEC. Now with introduction of new config
option, we can remove crypto dependency from other arches.
Now CONFIG_KEXEC_FILE is available only on x86_64. So whereever I had
CONFIG_X86_64 defined, I got rid of that.
For CONFIG_KEXEC_FILE, instead of doing select CRYPTO=y, I changed it to
"depends on CRYPTO=y". This should be safer as "select" is not
recursive.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Tested-by: Shaun Ruffell <sruffell@digium.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Sasha Levin has shown oopses on ffffea0003480048 and ffffea0003480008 at
mm/memory.c:1132, running Trinity on different 3.16-rc-next kernels:
where zap_pte_range() checks page->mapping to see if PageAnon(page).
Those addresses fit struct pages for pfns d2001 and d2000, and in each
dump a register or a stack slot showed d2001730 or d2000730: pte flags
0x730 are PCD ACCESSED PROTNONE SPECIAL IOMAP; and Sasha's e820 map has
a hole between cfffffff and 100000000, which would need special access.
Commit c46a7c817e ("x86: define _PAGE_NUMA by reusing software bits on
the PMD and PTE levels") has broken vm_normal_page(): a PROTNONE SPECIAL
pte no longer passes the pte_special() test, so zap_pte_range() goes on
to try to access a non-existent struct page.
Fix this by refining pte_special() (SPECIAL with PRESENT or PROTNONE) to
complement pte_numa() (SPECIAL with neither PRESENT nor PROTNONE). A
hint that this was a problem was that c46a7c817e added pte_numa() test
to vm_normal_page(), and moved its is_zero_pfn() test from slow to fast
path: This was papering over a pte_special() snag when the zero page was
encountered during zap. This patch reverts vm_normal_page() to how it
was before, relying on pte_special().
It still appears that this patch may be incomplete: aren't there other
places which need to be handling PROTNONE along with PRESENT? For
example, pte_mknuma() clears _PAGE_PRESENT and sets _PAGE_NUMA, but on a
PROT_NONE area, that would make it pte_special(). This is side-stepped
by the fact that NUMA hinting faults skipped PROT_NONE VMAs and there
are no grounds where a NUMA hinting fault on a PROT_NONE VMA would be
interesting.
Fixes: c46a7c817e ("x86: define _PAGE_NUMA by reusing software bits on the PMD and PTE levels")
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Tested-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Mel Gorman <mgorman@suse.de>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Cyrill Gorcunov <gorcunov@gmail.com>
Cc: Matthew Wilcox <matthew.r.wilcox@intel.com>
Cc: <stable@vger.kernel.org> [3.16]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
write{b,w,l,q}_relaxed are implemented by some architectures in order to
permit memory-mapped I/O writes with weaker barrier semantics than the
non-relaxed variants.
This patch implements these write macros for Alpha, in the same vein as
the relaxed read macros, which are already implemented.
Acked-by: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The KSTK_ESP macro is used to determine the user stack pointer for a
given task. In particular, this is used to to report the '[stack]' VMA
in /proc/self/maps, which is used by Android to determine the stack
location for children of the main thread.
This patch fixes the macro to use user_stack_pointer instead of directly
returning sp. This means that we report w13 instead of sp, since the
former is used as the stack pointer when executing in AArch32 state.
Cc: <stable@vger.kernel.org>
Reported-by: Serban Constantinescu <Serban.Constantinescu@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Commit 5f888a1d33 (ARM64: perf: support dwarf unwinding in compat mode)
changes user_stack_pointer() to return the compat SP for 32-bit tasks
but without brackets around the whole definition, with possible issues
on the call sites (noticed with a subsequent fix for KSTK_ESP).
Fixes: 5f888a1d33 (ARM64: perf: support dwarf unwinding in compat mode)
Reported-by: Sudeep Holla <sudeep.holla@arm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Now IOAPIC driver dynamically allocates IRQ numbers for IOAPIC pins.
We need to keep IRQ assignment for PCI devices during runtime power
management, otherwise it may cause failure of device wakeups.
Commit 3eec595235 "x86, irq, PCI: Keep IRQ assignment for PCI
devices during suspend/hibernation" has fixed the issue for suspend/
hibernation, we also need the same fix for runtime device sleep too.
Fix: https://bugzilla.kernel.org/show_bug.cgi?id=83271
Reported-and-Tested-by: EmanueL Czirai <amanual@openmailbox.org>
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: EmanueL Czirai <amanual@openmailbox.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Grant Likely <grant.likely@linaro.org>
Link: http://lkml.kernel.org/r/1409304383-18806-1-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The architecture specifies that when the processor wakes up from a WFE
or WFI instruction, the instruction is considered complete, however we
currrently return to EL1 (or EL0) at the WFI/WFE instruction itself.
While most guests may not be affected by this because their local
exception handler performs an exception returning setting the event bit
or with an interrupt pending, some guests like UEFI will get wedged due
this little mishap.
Simply skip the instruction when we have completed the emulation.
Cc: <stable@vger.kernel.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
X-Gene u-boot runs in EL2 mode with MMU enabled hence we might
have stale EL2 tlb enteris when we enable EL2 MMU on each host CPU.
This can happen on any ARM/ARM64 board running bootloader in
Hyp-mode (or EL2-mode) with MMU enabled.
This patch ensures that we flush all Hyp-mode (or EL2-mode) TLBs
on each host CPU before enabling Hyp-mode (or EL2-mode) MMU.
Cc: <stable@vger.kernel.org>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Pranavkumar Sawargaonkar <pranavkumar@linaro.org>
Signed-off-by: Anup Patel <anup.patel@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
The current perf_regs code relies on sp and pc sitting just off the end
of the pt_regs->regs array. This is ugly and fragile, so this patch
checks for these register explicitly and returns the appropriate field.
Acked-by: Jean Pihet <jean.pihet@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
copy_{to,from}_user return the number of bytes remaining on failure, not
an error code.
This patch returns -EFAULT when the copy operation didn't complete,
rather than expose the number of bytes not copied directly to userspace.
Signed-off-by: Will Deacon <will.deacon@arm.com>
I'm not sure what I was on when I wrote this, but when iterating over
the hardware watchpoint array (hbp_watch_array), our index is off by
ARM_MAX_BRP, so we walk off the end of our thread_struct...
... except, a dodgy condition in the loop means that it never executes
at all (bp cannot be NULL).
This patch fixes the code so that we remove the bp check and use the
correct index for accessing the watchpoint structures.
Cc: <stable@vger.kernel.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
(and a sneaky document addition that slipped from the previous pull-request)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=DaB2
-----END PGP SIGNATURE-----
Merge tag 'mfd-fixes-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull mfd fixes from Lee Jones:
"Couple of simple fixes due for the 3.17 rcs
(and a sneaky document addition that slipped from the previous
pull-request)"
* tag 'mfd-fixes-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd:
mfd: twl4030-power: Fix PM idle pin configuration to not conflict with regulators
mfd: tc3589x: Add device tree bindings
mfd: ab8500-core: Use 'ifdef' for config options
mfd: htc-i2cpld: Fix %d confusingly prefixed with 0x in format string
mfd: omap-usb-host: Fix %d confusingly prefixed with 0x in format string
Commit 43fef47f94 (mfd: twl4030-power: Add a configuration to turn
off oscillator during off-idle) added support for configuring the PMIC
to cut off resources during deeper idle states to save power.
This however caused regression for n900 display power that needed the
PMIC configuration to be disabled with commit d937678ab6 (ARM: dts:
Revert enabling of twl configuration for n900).
Turns out the root cause of the problem is that we must use
TWL4030_RESCONFIG_UNDEF instead of DEV_GRP_NULL to avoid disabling
regulators that may have been enabled before the init function
for twl4030-power.c runs. With TWL4030_RESCONFIG_UNDEF we let the
regulator framework control the regulators like it should. Here we
need to only configure the sys_clken and sys_off_mode triggers for
the regulators that cannot be done by the regulator framework as
it's not running at that point.
This allows us to enable the PMIC configuration for n900.
Fixes: 43fef47f94 (mfd: twl4030-power: Add a configuration to turn off oscillator during off-idle)
Cc: stable@vger.kernel.org # v3.16
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
To deal with IPs which are specific to dra74x and dra72x, maintain seperate
ocp interface lists, while keeping the common list for all common IPs.
Move USB OTG SS4 to dra74x only list since its unavailable in
dra72x and is giving an abort during boot. The dra72x only list
is empty for now and a placeholder for future hwmod additions which
are specific to dra72x.
Fixes: d904b38df0 ("ARM: DRA7: hwmod: Add SYSCONFIG for usb_otg_ss")
Reported-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
[paul@pwsan.com: fixed comment style to conform with CodingStyle]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
* ARM: shmobile: r8a7791: add missing 0x0100 for SDCKCR
This resolves a problem introduced by 4bfb358b1d
("ARM: shmobile: Add r8a7791 legacy SDHI clocks")
which was included in v3.15.
This fix does not have any run-time affect at this time.
* ARM: shmobile: r8a7790: add missing 0x0100 for SDCKCR
This resolves a problem introduced by 9f13ee6f83
("ARM: shmobile: r8a7790: add div4 clocks")
which was included in v3.11.
This fix does not have any run-time affect at this time.
* ARM: shmobile: sh73a0: Remove spurious 0x from SCIFB clock name
This resolves a problem introduced by a0f7e7496d
("ARM: shmobile: sh73a0: add CMT1 clock support for DT")
which was included in v3.17-rc1.
This fix does not have any run-time affect at this time as the clock in
question is used by a SCIF device that is not enabled by default.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=jurT
-----END PGP SIGNATURE-----
Merge tag 'renesas-clock-fixes-for-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes
Merge "Renesas ARM Based SoC Clock Fixes For v3.17" from Simon Horman:
* ARM: shmobile: r8a7791: add missing 0x0100 for SDCKCR
This resolves a problem introduced by 4bfb358b1d
("ARM: shmobile: Add r8a7791 legacy SDHI clocks")
which was included in v3.15.
This fix does not have any run-time affect at this time.
* ARM: shmobile: r8a7790: add missing 0x0100 for SDCKCR
This resolves a problem introduced by 9f13ee6f83
("ARM: shmobile: r8a7790: add div4 clocks")
which was included in v3.11.
This fix does not have any run-time affect at this time.
* ARM: shmobile: sh73a0: Remove spurious 0x from SCIFB clock name
This resolves a problem introduced by a0f7e7496d
("ARM: shmobile: sh73a0: add CMT1 clock support for DT")
which was included in v3.17-rc1.
This fix does not have any run-time affect at this time as the clock in
question is used by a SCIF device that is not enabled by default.
* tag 'renesas-clock-fixes-for-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r8a7791: add missing 0x0100 for SDCKCR
ARM: shmobile: r8a7790: add missing 0x0100 for SDCKCR
ARM: shmobile: sh73a0: Remove spurious 0x from SCIFB clock name
Signed-off-by: Olof Johansson <olof@lixom.net>
- Fixes suspend/resume issue on imx53-qsrb due to PMIC IRQ pin
configuration missing
- A couple small SolidRun board fixes/correction from Rabeeh
and Russell
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJT/XBJAAoJEFBXWFqHsHzOuqgH/3XqY4n0kL7lZQGRl8sBA/1m
bLtlKYaGjtn5ITXYONuWyxk9MrkCUaVUEEkcM3Gty6kHbCZ9F8nqSa5NiYs4MyGR
FiBX1GANmz96t61i90jlNNxHdPfnmgj3ZXEDTEj9g2brwGceUgQZv4/D59qSy41H
VlyIIOREQbrIoFlln1cEaKf2UXOpmSpB835QHROwy9K4aK0kZKAR4v5eqM2aQaIl
9VpvR5Xfsmr5vH/srlkY+Vc2ODVF1nQZsa3ikleAh2rzFQ4thwSKqpSxF7HL6EAo
zafJuI67ctyzIFk1PlsUuqCM2NimzACnpgrNG6Vn2KDq/JavNIsuyna0KgzzXqE=
=jOFz
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-3.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
Merge "ARM: imx: fixes for 3.17, 2nd take" from Shawn Guo:
i.MX fixes for 3.17, 2nd take:
- Fixes suspend/resume issue on imx53-qsrb due to PMIC IRQ pin
configuration missing
- A couple small SolidRun board fixes/correction from Rabeeh
and Russell
* tag 'imx-fixes-3.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: microsom-ar8035: MDIO pad must be set open drain
ARM: dts: hummingboard/cubox-i: change SPDIF output to be more descriptive
ARM: dts: hummingboard/cubox-i: add USB OC pinctrl configuration
ARM: dts: imx53-qsrb: Fix suspend/resume
Signed-off-by: Olof Johansson <olof@lixom.net>
by default as that's what many boards expect. Also fixes for omap5
clocks, PM wake-up events, GPIO interrupt cells for dra7, and few
other minor fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJT/PNtAAoJEBvUPslcq6VzQsoP/0a2WXN51/oqrhviMGURLDFy
57Mc6Yz4annJPeyzmD7myPEoppOAzC+Ysp04gC2Ig5ygj94KPJb5Mc2o28lZT4wr
OTNjQA2W+5CpefXHTRSRaoqcfOD9qUmcnb+rGTiTIxSu8DYxWaf8seAxL2Q2YJ7u
+DPREfhs0YZyA1kxiZy1xssR2pM1lsPthf0hBDxPyxaTnBxvWFlZAw+06xWVlA+G
Lk5NZZOFXKTKGV6Cq28q+FQvveUqW3An87pfFZZsSyBQfCIZdNDtCQ7OXCgjA+E2
OZ7fYh+phbFkr8W+0fJGu3b3t8ehFm74tvQ1qQlb0R0GrqRMaYXooO4Wk73sgJmc
MbaBGZ7CzkLC7IgvfitbdDRlFmrQeVHoBoH+UtwkNh4CyWtBzdrvxxgj8BvtJSYs
rWfppeEZrsWKdESNdjV4YFqkrMEHfyOlTjAqDUVd8CjtF1fOyQ/WkfpgqcpsYfj5
7YhW5qMjtYYmNoklU62sQyJx2HhpYpjdI83qmKT6zUM2OlrJYmco3FFXFRHRfNv2
o6M61iO+dwYuEjfZ1NhlCep41/MJ2El1oYMnNNvXy/DBveh9887TuX4S5WYIcF2M
ofhv4y3JDGPfXvvdpE/M1FiqHoJ0Epl+IUbaeNR61mbBmZZG3ExvPiqvYgdrhbnk
2kr7x8fPRfgsc41z1ajH
=i+aY
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.17/fixes-against-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Merge "omap fixes against v3.17-rc2" from Tony Lindgren:
Fixes for omaps, mostly to revert NAND back to using software ECC
by default as that's what many boards expect. Also fixes for omap5
clocks, PM wake-up events, GPIO interrupt cells for dra7, and few
other minor fixes.
* tag 'omap-for-v3.17/fixes-against-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: omap54xx-clocks: Fix the l3 and l4 clock rates
ARM: OMAP2+: hwmod: Rearm wake-up interrupts for DT when MUSB is idled
ARM: dts: Enable UART wake-up events for beagleboard
ARM: dts: Remove twl6030 clk32g "regulator"
ARM: OMAP2+: omap_device: remove warning that clk alias already exists
ARM: OMAP: fix %d confusingly prefixed with 0x in format string
ARM: dts: DRA7: fix interrupt-cells for GPIO
mtd: nand: omap: Fix 1-bit Hamming code scheme, omap_calculate_ecc()
ARM: dts: omap3430-sdp: Revert to using software ECC for NAND
ARM: OMAP2+: GPMC: Support Software ECC scheme via DT
mtd: nand: omap: Revert to using software ECC by default
Commit af040ffc9b ("ARM: make it easier to check the CPU part number
correctly") changed ARM_CPU_PART_X masks, and the way they are returned and
checked against. Usage of read_cpuid_part_number() is now deprecated, and
calling places updated accordingly. This actually broke cpuidle-big_little
initialization, as bl_idle_driver_init() performs a check using an hardcoded
mask on cpu_id.
Create an interface to perform the check (that is now even easier to read).
Define also a proper mask (ARM_CPU_PART_MASK) that makes this kind of checks
cleaner and helps preventing bugs in the future. Update usage accordingly.
Signed-off-by: Juri Lelli <juri.lelli@arm.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On revisions of Cortex-A15 prior to r3p3, a CLREX instruction at PL1 may
falsely trigger a watchpoint exception, leading to potential data aborts
during exception return and/or livelock.
This patch resolves the issue in the following ways:
- Replacing our uses of CLREX with a dummy STREX sequence instead (as
we did for v6 CPUs).
- Removing the clrex code from v7_exit_coherency_flush and derivatives,
since this only exists as a minor performance improvement when
non-cached exclusives are in use (Linux doesn't use these).
Benchmarking on a variety of ARM cores revealed no measurable
performance difference with this change applied, so the change is
performed unconditionally and no new Kconfig entry is added.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The ARMv6 and ARMv7 early abort handlers clear the exclusive monitors
upon entry to the kernel, but this is redundant:
- We clear the monitors on every exception return since commit
200b812d00 ("Clear the exclusive monitor when returning from an
exception"), so this is not necessary to ensure the monitors are
cleared before returning from a fault handler.
- Any dummy STREX will target a temporary scratch area in memory, and
may succeed or fail without corrupting useful data. Its status value
will not be used.
- Any other STREX in the kernel must be preceded by an LDREX, which
will initialise the monitors consistently and will not depend on the
earlier state of the monitors.
Therefore we have no reason to care about the initial state of the
exclusive monitors when a data abort is taken, and clearing the monitors
prior to exception return (as we already do) is sufficient.
This patch removes the redundant clearing of the exclusive monitors from
the early abort handlers.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Kernel module build with GCOV profiling fails to load with the
following error:
$ insmod test_module.ko
test_module: unknown relocation: 38
insmod: can't insert 'test_module.ko': invalid module format
This happens because constructor pointers in the .init_array section
have not supported R_ARM_TARGET1 relocation type.
Documentation (ELF for the ARM Architecture) says:
"The relocation must be processed either in the same way as R_ARM_REL32 or
as R_ARM_ABS32: a virtual platform must specify which method is used."
Since kernel expects to see absolute addresses in .init_array R_ARM_TARGET1
relocation type should be treated the same way as R_ARM_ABS32.
Signed-off-by: Andrey Ryabinin <a.ryabinin@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We allocate "len" number of chars so we should put the NUL at "len - 1"
to avoid corrupting memory. Btw, strlen_user() is different from the
normal strlen() function because it includes NUL terminator in the
count.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Helge Deller <deller@gmx.de>
Commit 15a3c7cc91 "x86, irq: Introduce two helper functions
to support irqdomain map operation" breaks LPSS ACPI enumerated
devices.
On startup, IOAPIC driver preallocates IRQ descriptors and programs
IOAPIC pins with default level and polarity attributes for all legacy
IRQs. Later legacy IRQ users may fail to set IOAPIC pin attributes
if the requested attributes conflicts with the default IOAPIC pin
attributes. So change mp_irqdomain_map() to allow the first legacy IRQ
user to reprogram IOAPIC pin with different attributes.
Reported-and-tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Prarit Bhargava <prarit@redhat.com>
Link: http://lkml.kernel.org/r/1409118795-17046-1-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch is important for the MicroSOM implementation due to the
following details -
1. VIH of the Atheros phy is 1.7V.
2. NVCC_ENET which is the power domain of the MDIO pad is driven by the
PHY's LDO (i.e. either 1.8v or 2.5v).
3. The MicroSOM implements an onbouard 1.6kohm pull up to 3.3v (R3000).
In the case the PHY's LDO was 1.8v then there would be only a 100mV
margin for the signal to be acknowledged as high (1.8v-1.7v).
Due to that setting the pad as an open drain will let the 1.6kohm pull
that signal high to 3.3 that assures enough margins to the PHY to be
acked as '1' logic.
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Pull s390 updates from Martin Schwidefsky:
- wire up the system calls seccomp, getrandom and memfd_create
- use static system information as input to add_device_randomness
- .. and three bug fixes
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/sclp: remove unnecessary XTABS flag
s390/3215: fix tty output containing tabs
s390: wire up memfd_create syscall
s390: add system information as device randomness
s390/kdump: Clear subchannel ID to signal non-CCW/SCSI IPL
s390: wire up seccomp and getrandom syscalls
Similarly to DRA7, OMAP5 has l3 and l4 clock rates incorrectly calculated.
Fixed by using proper divider clock types for the clock nodes.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reported-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove an unused local variable from head.S. It seems this was never
used even from the initial commit
9703d9d7f7 (arm64: Kernel booting and
initialisation), and is a left over from a previous implementation
of __calc_phys_offset.
Signed-off-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Originally found by cppcheck:
[arch/arm64/crypto/sha2-ce-glue.c:153]: (warning) Assignment of
function parameter has no effect outside the function. Did you
forget dereferencing it?
Updating data by blocks * SHA256_BLOCK_SIZE at the end of
sha2_finup is redundant code and can be removed.
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The edma_setup_from_hw() should know about the CC number when parsing the
CCCFG register - when it reads the register to be precise. The base
addresses for CCs stored in an array and we need to provide the correct id
to edma_read() in order to read the correct register.
Cc: <stable@vger.kernel.org> # 3.16
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
There were several issues (of varying degree of importance) pointed out
with this code late in the review cycle, yet the code was still merged.
Let's rip it out for now and look at resubmitting at a later time.
This reverts most of commit 4fbe66d990.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Looks like MUSB cable removal can cause wake-up interrupts to
stop working for device tree based booting at least for UART3
even as nothing is dynamically remuxed. This can be fixed by
calling reconfigure_io_chain() for device tree based booting
in hwmod code. Note that we already do that for legacy booting
if the legacy mux is configured.
My guess is that this is related to UART3 and MUSB ULPI
hsusb0_data0 and hsusb0_data1 support for Carkit mode that
somehow affect the configured IO chain for UART3 and require
rearming the wake-up interrupts.
In general, for device tree based booting, pinctrl-single
calls the rearm hook that in turn calls reconfigure_io_chain
so calling reconfigure_io_chain should not be needed from the
hwmod code for other events.
So let's limit the hwmod rearming of iochain only to
HWMOD_FORCE_MSTANDBY where MUSB is currently the only user
of it. If we see other devices needing similar changes we can
add more checks for it.
Cc: Paul Walmsley <paul@pwsan.com>
Cc: stable@vger.kernel.org # v3.16
Signed-off-by: Tony Lindgren <tony@atomide.com>
For device tree based booting, we need to use wake-up
interrupts like we already do for some omaps. This fixes
a PM regression on beagleboard compared to legacy booting.
Tested-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The kernel has never supported clk32g as a regulator since it is a clock
and not a regulator. Fortunately nothing actually references this node so
we can just remove it.
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
When an alias for a clock already exists the warning is printed. For
every module with a main_clk defined, a clk alias for fck is added.
There are some components that have the same main_clk defined, so this
is a really normal situation.
For example the am33xx edma device has 4 components using the same main
clock. So there are three warnings in the boot log for this already
existing clock alias:
platform 49000000.edma: alias fck already exists
platform 49000000.edma: alias fck already exists
platform 49000000.edma: alias fck already exists
As this is only interesting for developers, this patch changes the
message to a debug message.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
GPIO modules are also interrupt sources. However, they require both the
GPIO number and IRQ type to function properly.
By declaring that GPIO uses interrupt-cells=<1>, we essentially do not
allow users of the nodes to use the interrupt property appropritely.
With this change, the following now works:
interrupt-parent = <&gpio6>;
interrupts = <5 IRQ_TYPE_LEVEL_LOW>;
Fixes: 6e58b8f1da ('ARM: dts: DRA7: Add the dts files for dra7 SoC and dra7-evm board')
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
For v3.14 and prior, 1-bit Hamming code ECC via software was used
for NAND on this board.
Commit c06c527016 in v3.15 changed the behaviour
to use 1-bit Hamming code via Hardware using a different ECC layout
i.e. (ROM code layout) than what is used by software ECC.
This ECC layout change causes NAND filesystems created in v3.14
and prior to be unusable in v3.15 and later. So revert back to
using software ECC scheme.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
For v3.14 and prior, 1-bit Hamming code ECC via software was the
default choice for some boards e.g. 3430sdp.
Commit ac65caf514 in v3.15 changed the behaviour
to use 1-bit Hamming code via Hardware using a different ECC layout
i.e. (ROM code layout) than what is used by software ECC.
This ECC layout change causes NAND filesystems created in v3.14
and prior to be unusable in v3.15 and later. So don't mark "sw" scheme
as deperecated and support it.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
For v3.12 and prior, 1-bit Hamming code ECC via software was the
default choice. Commit c66d039197 in v3.13 changed the behaviour
to use 1-bit Hamming code via Hardware using a different ECC layout
i.e. (ROM code layout) than what is used by software ECC.
This ECC layout change causes NAND filesystems created in v3.12
and prior to be unusable in v3.13 and later. So revert back to
using software ECC by default if an ECC scheme is not explicitely
specified.
This defect can be observed on the following boards during legacy boot
-omap3beagle
-omap3touchbook
-overo
-am3517crane
-devkit8000
-ldp
-3430sdp
Signed-off-by: Roger Quadros <rogerq@ti.com>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
* Confine SH_INTC to platforms that need it
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=QSyy
-----END PGP SIGNATURE-----
Merge tag 'renesas-sh-drivers-for-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas
Pull SH driver fix from Simon Horman:
"Confine SH_INTC to platforms that need it"
* tag 'renesas-sh-drivers-for-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
sh: intc: Confine SH_INTC to platforms that need it
Pull MIPS fixes from Ralf Baechle:
"Pretty much all across the field so with this we should be in
reasonable shape for the upcoming -rc2"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: OCTEON: make get_system_type() thread-safe
MIPS: CPS: Initialize EVA before bringing up VPEs from secondary cores
MIPS: Malta: EVA: Rename 'eva_entry' to 'platform_eva_init'
MIPS: EVA: Add new EVA header
MIPS: scall64-o32: Fix indirect syscall detection
MIPS: syscall: Fix AUDIT value for O32 processes on MIPS64
MIPS: Loongson: Fix COP2 usage for preemptible kernel
MIPS: NL: Fix nlm_xlp_defconfig build error
MIPS: Remove race window in page fault handling
MIPS: Malta: Improve system memory detection for '{e, }memsize' >= 2G
MIPS: Alchemy: Fix db1200 PSC clock enablement
MIPS: BCM47XX: Fix reboot problem on BCM4705/BCM4785
MIPS: Remove duplicated include from numa.c
MIPS: Add common plat_irq_dispatch declaration
MIPS: MSP71xx: remove unused plat_irq_dispatch() argument
MIPS: GIC: Remove useless parens from GICBIS().
MIPS: perf: Mark pmu interupt IRQF_NO_THREAD
Upstream commit:
95d76acc75 ("x86, irq: Count legacy IRQs by legacy_pic->nr_legacy_irqs instead of NR_IRQS_LEGACY")
removed reserved interrupts for the platforms that do not have a legacy IOAPIC.
Which breaks the boot on Intel MID platforms such as Medfield:
BUG: unable to handle kernel NULL pointer dereference at 0000003a
IP: [<c107079a>] setup_irq+0xf/0x4d [ 0.000000] *pdpt = 0000000000000000 *pde = 9bbf32453167e510
The culprit is an uncoditional setting of IRQ2 which is used
as cascade IRQ on legacy platforms. It seems we have to check
if we have enough legacy IRQs reserved before we can call
setup_irq().
The fix adds such check in native_init_IRQ() and in setup_default_timer_irq().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jiang Liu <jiang.liu@linux.intel.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: David Cohen <david.a.cohen@linux.intel.com>
Link: http://lkml.kernel.org/r/1405931920-12871-1-git-send-email-andriy.shevchenko@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
1. a malicious user to trigger a kernel BUG
2. a malicious user to change the storage key of read-only pages
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=ED9q
-----END PGP SIGNATURE-----
Merge tag 'kvm-s390-20140825' of git://git.kernel.org/pub/scm/linux/kernel/git/kvms390/linux into kvm-master
Here are two fixes for s390 KVM code that prevent:
1. a malicious user to trigger a kernel BUG
2. a malicious user to change the storage key of read-only pages
The PFMF instruction handler blindly wrote the storage key even if
the page was mapped R/O in the host. Lets try a COW before continuing
and bail out in case of errors.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Dominik Dingel <dingel@linux.vnet.ibm.com>
Cc: stable@vger.kernel.org
In the early days, we had some special handling for the
KVM_EXIT_S390_SIEIC exit, but this was gone in 2009 with commit
d7b0b5eb30 (KVM: s390: Make psw available on all exits, not
just a subset).
Now this switch statement is just a sanity check for userspace
not messing with the kvm_run structure. Unfortunately, this
allows userspace to trigger a kernel BUG. Let's just remove
this switch statement.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Cc: stable@vger.kernel.org
Hummingboard has no over current hardware, so disable the over current
detection for both ports.
Cubox-i has over current hardware, so appropriately configure this.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Pull x86 fixes from Ingo Molnar:
"A couple of EFI fixes, plus misc fixes all around the map"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi/arm64: Store Runtime Services revision
firmware: Do not use WARN_ON(!spin_is_locked())
x86_32, entry: Clean up sysenter_badsys declaration
x86/doc: Fix the 'tlb_single_page_flush_ceiling' sysconfig path
x86/mm: Fix sparse 'tlb_single_page_flush_ceiling' warning and make the variable read-mostly
x86/mm: Fix RCU splat from new TLB tracepoints
A collection of fixes from this week, it's been pretty quiet and nothing
really stands out as particularly noteworthy here -- mostly minor fixes
across the field:
- ODROID booting was fixed due to PMIC interrupts missing in DT
- A collection of i.MX fixes
- Minor Tegra fix for regulators
- Rockchip fix and addition of SoC-specific mailing list to make it
easier to find posted patches.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=+oYu
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A collection of fixes from this week, it's been pretty quiet and
nothing really stands out as particularly noteworthy here -- mostly
minor fixes across the field:
- ODROID booting was fixed due to PMIC interrupts missing in DT
- a collection of i.MX fixes
- minor Tegra fix for regulators
- Rockchip fix and addition of SoC-specific mailing list to make it
easier to find posted patches"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
bus: arm-ccn: Fix warning message
ARM: shmobile: koelsch: Remove non-existent i2c6 pinmux
ARM: tegra: apalis/colibri t30: fix on-module 5v0 supplies
MAINTAINERS: add new Rockchip SoC list
ARM: dts: rockchip: readd missing mmc0 pinctrl settings
ARM: dts: ODROID i2c improvements
ARM: dts: Enable PMIC interrupts on ODROID
ARM: dts: imx6sx: fix the pad setting for uart CTS_B
ARM: dts: i.MX53: fix apparent bug in VPU clks
ARM: imx: correct gpu2d_axi and gpu3d_axi clock setting
ARM: dts: imx6: edmqmx6: change enet reset pin
ARM: dts: vf610-twr: Fix pinctrl_esdhc1 pin definitions.
ARM: imx: remove unnecessary ARCH_HAS_OPP select
ARM: imx: fix TLB missing of IOMUXC base address during suspend
ARM: imx6: fix SMP compilation again
ARM: dt: sun6i: Add #address-cells and #size-cells to i2c controller nodes
On r8a7791, i2c6 (aka iic3) doesn't need pinmux, but the koelsch dts
refers to non-existent pinmux configuration data:
pinmux core: sh-pfc does not support function i2c6
sh-pfc e6060000.pfc: invalid function i2c6 in map table
Remove it to fix this.
Fixes: commit 1d41f36a68 ("ARM: shmobile:
koelsch dts: Add VDD MPU regulator for DVFS")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Olof Johansson <olof@lixom.net>
Working on Gigabit/PCIe support in U-Boot for Apalis T30 I realised
that the current device tree source includes for our modules only
happen to work due to referencing the on-carrier 5v0 supply from USB
which is not at all available on-module. The modules actually contain
TPS60150 charge pumps to generate the PMIC required 5 volts from the
one and only 3.3 volt module supply. This patch fixes this.
(Note: When back-porting this to v3.16 stable releases, simply drop the
change to tegra30-apalis.dtsi; that file was added in v3.17)
Cc: <stable@vger.kernel.org> #v3.16+
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
dts files and addition of the new Rockchip list to MAINTAINERS.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCAAGBQJT+hwkAAoJEPOmecmc0R2Bda4IAJ7rxypWxi8RtfxULHu1oGxZ
cdmAsaedAkjTn6tye/99lv1WkLzUD+Q3AxLX6Glu8PgTkocbwtkVTP+gMbv7zwfN
Z9bA6kazPL4Rskr6Am8BFKkGhXHCXChGP1J3z9Gyh07Vu2+3zsvRzyM7hySt3TqZ
EA2dL/uODlukw6EPzFaqGWZLn1OuJmkHXDfnZ3lBI/GFZD9qt5DnYswMBlDlIwr6
D08jmcleRA3wpnY1HXYR2cN1sJmcEP6xVE8ApXd71X0MtumEy49ZTR+4T5/Sh/XN
OPheoH3UUVtXVrAa5fsoUE2xsKs3PZgnIHk1kQklpbw+HArbN+aW0Jh6CySb65Q=
=aNJj
-----END PGP SIGNATURE-----
Merge tag 'v3.17-rockchip-fixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into fixes
Merge "ARM: rockchip: fix for 3.17" from Heiko Stubner:
Pinctrl that got accidentially dropped when reorganizing the
dts files and addition of the new Rockchip list to MAINTAINERS.
* tag 'v3.17-rockchip-fixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
MAINTAINERS: add new Rockchip SoC list
ARM: dts: rockchip: readd missing mmc0 pinctrl settings
Signed-off-by: Olof Johansson <olof@lixom.net>
During the restructuring of the Rockchip Cortex-A9 dtsi files it seems
like the pinctrl settings vanished at some point from the mmc0 support.
This of course renders them unusable, so readd the necessary pinctrl
properties.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Only a single patch in here that fixes a DTC warning.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=PL45
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt-for-3.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into fixes
Merge "Allwinner DT changes, take 2" from Maxime Ripard:
Only a single patch in here that fixes a DTC warning.
* tag 'sunxi-dt-for-3.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
ARM: dt: sun6i: Add #address-cells and #size-cells to i2c controller nodes
Signed-off-by: Olof Johansson <olof@lixom.net>
This small set of fixes addresses a few issues introduced during the
merge window, including:
- Fix typo in I-cache detection that was causing us to treat all
I-caches as aliasing
- Hook up memfd_create and getrandom syscalls for native and compat
- Revert a temporary hack for defconfig builds in -next (the audit
tree changes didn't make it in this merge window)
- A couple of UEFI fixes for TEXT_OFFSET fuzzing and /memreserve/
- A simple sparsemem fix for 48-bit physical addressing
- Small defconfig updates to get autotesters working with X-gene
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=BqdY
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"This small set of fixes addresses a few issues introduced during the
merge window, including:
- fix typo in I-cache detection that was causing us to treat all
I-caches as aliasing
- hook up memfd_create and getrandom syscalls for native and compat
- revert a temporary hack for defconfig builds in -next (the audit
tree changes didn't make it in this merge window)
- a couple of UEFI fixes for TEXT_OFFSET fuzzing and /memreserve/
- a simple sparsemem fix for 48-bit physical addressing
- small defconfig updates to get autotesters working with X-gene"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
Revert "arm64: Do not invoke audit_syscall_* functions if !CONFIG_AUDIT_SYSCALL"
arm64: mm: update max pa bits to 48
arm64: ignore DT memreserve entries when booting in UEFI mode
arm64: configs: Enable X-Gene SATA and ethernet in defconfig
arm64: align randomized TEXT_OFFSET on 4 kB boundary
asm-generic: add memfd_create system call to unistd.h
arm64: compat: wire up memfd_create and getrandom syscalls for aarch32
arm64: fix typo in I-cache policy detection
Swap it for the more canonical lockdep_assert_held() which always
does the right thing - Guenter Roeck
* Assign the correct value to efi.runtime_version on arm64 so that all
the runtime services can be invoked - Semen Protsenko
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=IUiu
-----END PGP SIGNATURE-----
Merge tag 'efi-urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/mfleming/efi into x86/urgent
Pull EFI fixes from Matt Fleming:
* WARN_ON(!spin_is_locked()) always triggers on non-SMP machines.
Swap it for the more canonical lockdep_assert_held() which always
does the right thing - Guenter Roeck
* Assign the correct value to efi.runtime_version on arm64 so that all
the runtime services can be invoked - Semen Protsenko
Signed-off-by: Ingo Molnar <mingo@kernel.org>
"efi" global data structure contains "runtime_version" field which must
be assigned in order to use it later in Runtime Services virtual calls
(virt_efi_* functions).
Before this patch "runtime_version" was unassigned (0), so each
Runtime Service virtual call that checks revision would fail.
Signed-off-by: Semen Protsenko <semen.protsenko@linaro.org>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Currently the sh-intc driver is compiled on all SuperH and
non-multiplatform SH-Mobile platforms, while it's only used on a limited
number of platforms:
- SuperH: SH2(A), SH3(A), SH4(A)(L) (all but SH5)
- ARM: sh7372, sh73a0
Drop the "default y" on SH_INTC, make all CPU platforms that use it
select it, and protect all sub-options by "if SH_INTC" to fix this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
4bfb358b1d
(ARM: shmobile: Add r8a7791 legacy SDHI clocks)
added r8a7791 SDHI clock support.
But, it is missing
"0x0100: x 1/8" division ratio.
This patch fixes hidden bug.
It is based on R-Car H2 v0.7, R-Car M2 v0.9.
Reported-by: Yusuke Goda <yusuke.goda.sx@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
9f13ee6f83
(ARM: shmobile: r8a7790: add div4 clocks)
added r8a7790 DIV4 clock support.
But, it is missing
"0x0100: x 1/8" division ratio.
This patch fixes hidden bug.
It is based on R-Car H2 v0.7, R-Car M2 v0.9.
Reported-by: Yusuke Goda <yusuke.goda.sx@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Set 'ti,set-rate-parent' property for the dpll4_m5x2_ck clock, which
is used for the ISP functional clock. This fixes the OMAP3 ISP driver's
clock rate configuration on OMAP34xx, which needs the rate to be
propagated properly to the divider node (dpll4_m5_ck).
Signed-off-by: Stefan Herbrechtsmeier <stefan@herbrechtsmeier.net>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: <linux-media@vger.kernel.org>
Cc: <linux-omap@vger.kernel.org>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
