ASSR is an optional feature, so it's a valid operating condition for
the display to reject ASSR enable. Demote the warning to the debug
level.
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by:Andrey Gusakov <andrey.gusakov@cogentembedded.com>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20161130114810.3245-1-l.stach@pengutronix.de
The Amlogic Meson Display controller is composed of several components :
DMC|---------------VPU (Video Processing Unit)----------------|------HHI------|
| vd1 _______ _____________ _________________ | |
D |-------| |----| | | | | HDMI PLL |
D | vd2 | VIU | | Video Post | | Video Encoders |<---|-----VCLK |
R |-------| |----| Processing | | | | |
| osd2 | | | |---| Enci ----------|----|-----VDAC------|
R |-------| CSC |----| Scalers | | Encp ----------|----|----HDMI-TX----|
A | osd1 | | | Blenders | | Encl ----------|----|---------------|
M |-------|______|----|____________| |________________| | |
___|__________________________________________________________|_______________|
VIU: Video Input Unit
---------------------
The Video Input Unit is in charge of the pixel scanout from the DDR memory.
It fetches the frames addresses, stride and parameters from the "Canvas" memory.
This part is also in charge of the CSC (Colorspace Conversion).
It can handle 2 OSD Planes and 2 Video Planes.
VPP: Video Post Processing
--------------------------
The Video Post Processing is in charge of the scaling and blending of the
various planes into a single pixel stream.
There is a special "pre-blending" used by the video planes with a dedicated
scaler and a "post-blending" to merge with the OSD Planes.
The OSD planes also have a dedicated scaler for one of the OSD.
VENC: Video Encoders
--------------------
The VENC is composed of the multiple pixel encoders :
- ENCI : Interlace Video encoder for CVBS and Interlace HDMI
- ENCP : Progressive Video Encoder for HDMI
- ENCL : LCD LVDS Encoder
The VENC Unit gets a Pixel Clocks (VCLK) from a dedicated HDMI PLL and clock
tree and provides the scanout clock to the VPP and VIU.
The ENCI is connected to a single VDAC for Composite Output.
The ENCI and ENCP are connected to an on-chip HDMI Transceiver.
This driver is a DRM/KMS driver using the following DRM components :
- GEM-CMA
- PRIME-CMA
- Atomic Modesetting
- FBDev-CMA
For the following SoCs :
- GXBB Family (S905)
- GXL Family (S905X, S905D)
- GXM Family (S912)
The current driver only supports the CVBS PAL/NTSC output modes, but the
CRTC/Planes management should support bigger modes.
But Advanced Colorspace Conversion, Scaling and HDMI Modes will be added in
a second time.
The Device Tree bindings makes use of the endpoints video interface definitions
to connect to the optional CVBS and in the future the HDMI Connector nodes.
HDMI Support is planned for a next release.
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
single drm fix.
* tag 'drm-misc-fixes-2016-11-30' of git://anongit.freedesktop.org/git/drm-misc:
drm: Don't call drm_for_each_crtc with a non-KMS driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=7Fpy
-----END PGP SIGNATURE-----
Merge tag 'tilcdc-4.10' of https://github.com/jsarha/linux into drm-next
tilcdc changes for v4.10
* tag 'tilcdc-4.10' of https://github.com/jsarha/linux: (23 commits)
drm/tilcdc: fix parsing of some DT properties
drm/tilcdc: Enable frame done irq and functionality for LCDC rev 1
drm/tilcdc: Configure video mode to HW in enable() not in mode_set_nofb()
drm/tilcdc: Load palette at the end of mode_set_nofb()
drm/tilcdc: Add timeout wait for palette loading to complete
drm/tilcdc: Enable palette loading for revision 2 LCDC too
drm/tilcdc: Fix load mode bit-field setting in tilcdc_crtc_enable()
drm/tilcdc: Add tilcdc_write_mask() to tilcdc_regs.h
drm/tilcdc: Fix tilcdc_crtc_create() return value handling
drm/tilcdc: implement palette loading for rev1
drm/tilcdc: Enable sync lost error and recovery handling for rev 1 LCDC
drm/tilcdc: Add drm bridge support for attaching drm bridge drivers
drm/bridge: Add ti-tfp410 DVI transmitter driver
dt-bindings: Move "ti,tfp410.txt" from display/ti to display/bridge
drm/tilcdc: Recover from sync lost error flood by resetting the LCDC
drm/tilcdc: Fix race from forced shutdown of crtc in unload
drm/tilcdc: Use unload to handle initialization failures
drm/tilcdc: Stop using struct drm_driver load() callback
drm/tilcdc: Remove obsolete drm_connector_register() calls
drm/tilcdc: Correct misspelling in error message
...
On the userspace side, all the basics are working, and most of glmark2
is working. I've been working through deqp, and I've got a couple more
things to fix (but we've gone from 70% to 80+% pass in last day, and
current deqp run that is going should pick up another 5-10%). I expect
to push the mesa patches today or tomorrow.
There are a couple more a5xx related patches to take the gpu out of
secure mode (for the devices that come up in secure mode, like the hw
I have), but those depend on an scm patch that would come in through
another tree. If that can land in the next day or two, there might
be a second late pull request for drm/msm.
In addition to the new-shiny, there have also been a lot of overlay/
plane related fixes for issues found using drm-hwc2 (in the process of
testing/debugging the atomic/kms fence patches), resulting in rework
to assign hwpipes to kms planes dynamically (as part of global atomic
state) and also handling SMP (fifo) block allocation atomically as
part of the ->atomic_check() step. All those patches should also help
out atomic weston (when those patches eventually land).
* 'msm-next' of git://people.freedesktop.org/~robclark/linux: (36 commits)
drm/msm: gpu: Add support for the GPMU
drm/msm: gpu: Add A5XX target support
drm/msm: Disable interrupts during init
drm/msm: Remove 'src_clk' from adreno configuration
drm/msm: gpu: Add OUT_TYPE4 and OUT_TYPE7
drm/msm: Add adreno_gpu_write64()
drm/msm: gpu Add new gpu register read/write functions
drm/msm: gpu: Return error on hw_init failure
drm/msm: gpu: Cut down the list of "generic" registers to the ones we use
drm/msm: update generated headers
drm/msm/adreno: move scratch register dumping to per-gen code
drm/msm/rd: support for 64b iova
drm/msm: convert iova to 64b
drm/msm: set dma_mask properly
drm/msm: Remove bad calls to of_node_put()
drm/msm/mdp5: move LM bounds check into plane->atomic_check()
drm/msm/mdp5: dump smp state on errors too
drm/msm/mdp5: add debugfs to show smp block status
drm/msm/mdp5: handle SMP block allocations "atomically"
drm/msm/mdp5: dynamically assign hw pipes to planes
...
The DT binding for tildc is not consistent with the driver code: there
are two options - 'max-width' and 'max-pixelclock' specified in the
documentation which are parsed as 'ti,max-width' and
'ti,max-pixelclock' respectively.
Make the driver code consistent with the binding.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
We should wait for the last frame to complete before shutting things
down also on LCDC rev 1.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Tested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Configure video mode to HW in enable() call back. There is no reason
to do it before that. This makes PM functions way easier because there
is no HW context to save when screen is for instance blanked. This
patch removes mode_set_nofb() call back from tilcdc.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Tested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Load palette at the end of mode_set_nofb(). Moving the palette loading
to mode_set_nofb() saves us from storing and restoring of framebuffer
addresses in dma registers that were just recently written there.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Tested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Add timeout wait for palette loadind to complete. We do not want to
hang forever if palette loaded interrupt does not arrive for some
reason.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Tested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The LCDC revision 2 documentation also mentions the mandatory palette
for true color modes. Even if the rev 2 LCDC appears to work just fine
without the palette being loaded loading it helps in testing the
feature.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Tested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Set LCDC_PALETTE_LOAD_MODE bit-field with new tilcdc_write_mask()
instead of tilcdc_set(). Setting a bit-fields with tilcdc_set() is
fundamentally broken.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Tested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Add tilcdc_write_mask() for handling register field wider than one bit
and mask values for those fields.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Tested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Failed tilcdc_crtc_create() error handling was broken, this patch
should fix it.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Tested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Revision 1 of the IP doesn't work if we don't load the palette (even
if it's not used, which is the case for the RGB565 format).
Add a function called from tilcdc_crtc_enable() which performs all
required actions if we're dealing with a rev1 chip.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Tested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Revision 1 LCDC support also sync lost errors and can benefit from
sync lost recovery routine.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Tested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Adds drm bride support for attaching drm bridge drivers to tilcdc. The
decision whether a video port leads to an external encoder or bridge
is made simply based on remote device's compatible string. The code
has been tested with BeagleBone-Black with and without BeagleBone
DVI-D Cape Rev A3 using ti-tfp410 driver.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Tested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Add very basic ti-tfp410 DVI transmitter driver. The only feature
separating this from a completely dummy bridge is the EDID read
support trough DDC I2C. Even that functionality should be in a
separate generic connector driver. However, because of missing DRM
infrastructure support the connector is implemented within the bridge
driver. Some tfp410 HW specific features may be added later if needed,
because there is a set of registers behind i2c if it is connected.
This implementation is tested against my new tilcdc bridge support
and it works with BeagleBone DVI-D Cape Rev A3. A DT binding document
is also updated.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Recover from sync lost error flood by resetting the LCDC instead of
turning off the SYNC_LOST error IRQ. When LCDC starves on limited
memory bandwidth it may sometimes result an error situation when the
picture may have shifted couple of pixels to right and SYNC_LOST
interrupt is generated on every frame. LCDC main reset recovers from
this situation and causes a brief blanking on the screen.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Tested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
We grab the struct_mutex in intel_crtc_page_flip, but if we are wedged
or a reset is in progress we bail early but never seem to actually
release the lock.
Fixes: 7f1847ebf4 ("drm/i915: Simplify checking of GPU reset_counter in display pageflips")
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20161128103648.9235-1-matthew.auld@intel.com
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: <stable@vger.kernel.org> # v4.7+
(cherry picked from commit ddbb271aea)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
On the DMA mapping error path, sg may be NULL (it has already been
marked as the last scatterlist entry), and we should avoid dereferencing
it again.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: e227330223 ("drm/i915: avoid leaking DMA mappings")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Imre Deak <imre.deak@intel.com>
Cc: stable@vger.kernel.org
Link: http://patchwork.freedesktop.org/patch/msgid/20161114112930.2033-1-chris@chris-wilson.co.uk
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
(cherry picked from commit b17993b7b2)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Big thing is that drm-misc is now officially a group maintainer/committer
model thing, with MAINTAINERS suitably updated. Otherwise just the usual
pile of misc things all over, nothing that stands out this time around.
* tag 'drm-misc-next-2016-11-29' of git://anongit.freedesktop.org/git/drm-misc: (33 commits)
drm: Introduce drm_framebuffer_assign()
drm/bridge: adv7511: Enable the audio data and clock pads on adv7533
drm/bridge: adv7511: Add Audio support
drm/edid: Consider alternate cea timings to be the same VIC
drm/atomic: Constify drm_atomic_crtc_needs_modeset()
drm: bridge: dw-hdmi: add ASoC dependency
drm: Fix shift operations for drm_fb_helper::drm_target_preferred()
drm: Avoid NULL dereference for DRM_LEGACY debug message
drm: Use u64_to_user_ptr() helper for blob ioctls
drm: Fix conflicting macro parameter in drm_mm_for_each_node_in_range()
drm: Fixup kernel doc for driver->gem_create_object
drm/hisilicon/hibmc: mark PM functions __maybe_unused
drm/hisilicon/hibmc: Checking for NULL instead of IS_ERR()
drm: bridge: add DesignWare HDMI I2S audio support
drm: Check against color expansion in drm_mm_reserve_node()
drm: Define drm_mm_for_each_node_in_range()
drm/doc: Fix links in drm_property.c
MAINTAINERS: Add link to drm-misc documentation
vgaarb: use valid dev pointer in vgaarb_info()
drm/atomic: Unconfuse the old_state mess in commmit_tail
...
Final 4.10 updates:
- fine-tune fb flushing and tracking (Chris Wilson)
- refactor state check dumper code for more conciseness (Tvrtko)
- roll out dev_priv all over the place (Tvrkto)
- finally remove __i915__ magic macro (Tvrtko)
- more gvt bugfixes (Zhenyu&team)
- better opregion CADL handling (Jani)
- refactor/clean up wm programming (Maarten)
- gpu scheduler + priority boosting for flips as first user (Chris
Wilson)
- make fbc use more atomic (Paulo)
- initial kvm-gvt framework, but not yet complete (Zhenyu&team)
* tag 'drm-intel-next-2016-11-21' of git://anongit.freedesktop.org/git/drm-intel: (127 commits)
drm/i915: Update DRIVER_DATE to 20161121
drm/i915: Skip final clflush if LLC is coherent
drm/i915: Always flush the dirty CPU cache when pinning the scanout
drm/i915: Don't touch NULL sg on i915_gem_object_get_pages_gtt() error
drm/i915: Check that each request phase is completed before retiring
drm/i915: i915_pages_create_for_stolen should return err ptr
drm/i915: Enable support for nonblocking modeset
drm/i915: Be more careful to drop the GT wakeref
drm/i915: Move frontbuffer CS write tracking from ggtt vma to object
drm/i915: Only dump dp_m2_n2 configuration when drrs is used
drm/i915: don't leak global_timeline
drm/i915: add i915_address_space_fini
drm/i915: Add a few more sanity checks for stolen handling
drm/i915: Waterproof verification of gen9 forcewake table ranges
drm/i915: Introduce enableddisabled helper
drm/i915: Only dump possible panel fitter config for the platform
drm/i915: Only dump scaler config where supported
drm/i915: Compact a few pipe config debug lines
drm/i915: Don't log pipe config kernel pointer and duplicated pipe name
drm/i915: Dump FDI config only where applicable
...
drm/qxl: various bugfixes and cleanups,
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=OYiT
-----END PGP SIGNATURE-----
Merge tag 'drm-qemu-20161121' of git://git.kraxel.org/linux into drm-next
drm/virtio: fix busid in a different way, allocate more vbufs.
drm/qxl: various bugfixes and cleanups,
* tag 'drm-qemu-20161121' of git://git.kraxel.org/linux: (224 commits)
drm/virtio: allocate some extra bufs
qxl: Allow resolution which are not multiple of 8
qxl: Don't notify userspace when monitors config is unchanged
qxl: Remove qxl_bo_init() return value
qxl: Call qxl_gem_{init, fini}
qxl: Add missing '\n' to qxl_io_log() call
qxl: Remove unused prototype
qxl: Mark some internal functions as static
Revert "drm: virtio: reinstate drm_virtio_set_busid()"
drm/virtio: fix busid regression
drm: re-export drm_dev_set_unique
Linux 4.9-rc5
gp8psk: Fix DVB frontend attach
gp8psk: fix gp8psk_usb_in_op() logic
dvb-usb: move data_mutex to struct dvb_usb_device
iio: maxim_thermocouple: detect invalid storage size in read()
aoe: fix crash in page count manipulation
lightnvm: invalid offset calculation for lba_shift
Kbuild: enable -Wmaybe-uninitialized warnings by default
pcmcia: fix return value of soc_pcmcia_regulator_set
...
Thanks for pulling the previous patch for HDLCD. Unfortunately,
yesterday Robin Murphy discovered another issue while playing with
CMA allocation sizes, which he has submitted a fix for.
* 'for-upstream/hdlcd' of git://linux-arm.org/linux-ld:
drm: hdlcd: Fix cleanup order
There was a small window where a userspace program could submit
a pageflip after receiving a pageflip completion event yet still
receive EBUSY.
Signed-off-by: Derek Foreman <derekf@osg.samsung.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Daniel Stone <daniels@collabora.com>
Encoders&planes can't be hotplugged, we dont need locking for this
since it's all single-threaded driver setup/teardown code. CRTCs
already don't grab locks.
While at it I noticed that plane's are missing the
drm_modeset_lock_fini() call, so add it.
Reviewed-by: Frank Binns <frank.binns@imgtec.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20161129094538.9650-1-daniel.vetter@ffwll.ch
Though we only walk the kernel_fb_helper_list inside a panic (or single
thread debugging), we still need to protect the list manipulation on
creating/removing a framebuffer device in order to prevent list
corruption.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20161129120217.7344-3-chris@chris-wilson.co.uk
drm_fb_helper_probe_connector_modes() is always called before
drm_setup_crtcs(), so just move the call into drm_setup_crtcs for a
small bit of code compaction.
Note that register_framebuffer will do a modeset (when fbcon is enabled)
and hence must be moved out of the critical section. A follow-up patch
will add new locking for the fb list, hence move all the related
registration code together.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20161129120217.7344-2-chris@chris-wilson.co.uk
The fb_helper->connector_count is modified when a new connector is
constructed following a hotplug event (e.g. DP-MST). This causes trouble
for drm_setup_crtcs() and friends that assume that fb_helper is
constant:
[ 1250.872997] BUG: KASAN: slab-out-of-bounds in drm_setup_crtcs+0x320/0xf80 at addr ffff88074cdd2608
[ 1250.873020] Write of size 40 by task kworker/u8:3/480
[ 1250.873039] CPU: 2 PID: 480 Comm: kworker/u8:3 Tainted: G U 4.9.0-rc6+ #285
[ 1250.873043] Hardware name: /NUC6i3SYB, BIOS SYSKLi35.86A.0024.2015.1027.2142 10/27/2015
[ 1250.873050] Workqueue: events_unbound async_run_entry_fn
[ 1250.873056] ffff88070f9d78f0 ffffffff814b72aa ffff88074e40c5c0 ffff88074cdd2608
[ 1250.873067] ffff88070f9d7918 ffffffff8124ff3c ffff88070f9d79b0 ffff88074cdd2600
[ 1250.873079] ffff88074e40c5c0 ffff88070f9d79a0 ffffffff812501e4 0000000000000005
[ 1250.873090] Call Trace:
[ 1250.873099] [<ffffffff814b72aa>] dump_stack+0x67/0x9d
[ 1250.873106] [<ffffffff8124ff3c>] kasan_object_err+0x1c/0x70
[ 1250.873113] [<ffffffff812501e4>] kasan_report_error+0x204/0x4f0
[ 1250.873120] [<ffffffff81698df0>] ? drm_dev_printk+0x140/0x140
[ 1250.873127] [<ffffffff81250ac3>] kasan_report+0x53/0x60
[ 1250.873134] [<ffffffff81688b40>] ? drm_setup_crtcs+0x320/0xf80
[ 1250.873142] [<ffffffff8124f18e>] check_memory_region+0x13e/0x1a0
[ 1250.873147] [<ffffffff8124f5f3>] memset+0x23/0x40
[ 1250.873154] [<ffffffff81688b40>] drm_setup_crtcs+0x320/0xf80
[ 1250.873161] [<ffffffff810be7c5>] ? wake_up_q+0x45/0x80
[ 1250.873169] [<ffffffff81b0c180>] ? mutex_lock_nested+0x5a0/0x5a0
[ 1250.873176] [<ffffffff8168a0e6>] drm_fb_helper_initial_config+0x206/0x7a0
[ 1250.873183] [<ffffffff81689ee0>] ? drm_fb_helper_set_par+0x90/0x90
[ 1250.873303] [<ffffffffa0b68690>] ? intel_fbdev_fini+0x140/0x140 [i915]
[ 1250.873387] [<ffffffffa0b686b2>] intel_fbdev_initial_config+0x22/0x40 [i915]
[ 1250.873391] [<ffffffff810b50ff>] async_run_entry_fn+0x7f/0x270
[ 1250.873394] [<ffffffff810a64b0>] process_one_work+0x3d0/0x960
[ 1250.873398] [<ffffffff810a641d>] ? process_one_work+0x33d/0x960
[ 1250.873401] [<ffffffff810a60e0>] ? max_active_store+0xf0/0xf0
[ 1250.873406] [<ffffffff810f6f9d>] ? do_raw_spin_lock+0x10d/0x1a0
[ 1250.873413] [<ffffffff810a767d>] worker_thread+0x8d/0x840
[ 1250.873419] [<ffffffff810a75f0>] ? create_worker+0x2e0/0x2e0
[ 1250.873426] [<ffffffff810b0454>] kthread+0x194/0x1c0
[ 1250.873432] [<ffffffff810b02c0>] ? kthread_park+0x60/0x60
[ 1250.873438] [<ffffffff810f095d>] ? trace_hardirqs_on+0xd/0x10
[ 1250.873446] [<ffffffff810b02c0>] ? kthread_park+0x60/0x60
[ 1250.873453] [<ffffffff810b02c0>] ? kthread_park+0x60/0x60
[ 1250.873457] [<ffffffff81b12277>] ret_from_fork+0x27/0x40
[ 1250.873460] Object at ffff88074cdd2608, in cache kmalloc-32 size: 32
However, when holding the mode_config.lock around the fb_helper, we have
to be careful of any callbacks that may reenter the fb_helper and so try
to reacquire the mode_config.lock (e.g. register_framebuffer). To avoid
the mutex recursion, we have to rearrange the sequence to move the
registration into the caller outside of the mode_config.lock.
v2: drop the 1; following the lockdep assertion inside the for(;;), I
anticipated an error that doesn't happen!
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=98826
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20161129120217.7344-1-chris@chris-wilson.co.uk
Fix race from forced shutdown of crtc in unload by adding internal
locking and a boolean telling if device is going to be shutdown.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Use unload to handle initialization failures instead of complex goto
label mess. To do this the initialization sequence needed slight
reordering and some unload functions needed to become conditional.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Stop using struct drm_driver load() and unload() callbacks. The
callbacks should not be used anymore. Instead of using load the
drm_device is allocated with drm_dev_alloc() and registered with
drm_dev_register() only after the driver is completely initialized.
The deinitialization is done directly either in component unbind
callback or in platform driver demove callback.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Remove obsolete drm_connector_register() calls from tilcdc_panel.c and
tilcdc_tfp410.c. All connectors are registered when drm_dev_register()
is called.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
This error message will be printed when a FIFO underflow irq has
triggered. Since this happens sometimes and the error message will be
displayed on the console, it should have a correct spelling.
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
The commit d8ff0c63fbcb ("drm/tilcdc: Adjust the FB_CEILING address")
added an adjustment of the FB_CEILING address. This is done by decrementing
the address by one.
On the AM335x (rev 0x4F201000) the framebuffer is rotated left over the
display border, because the ceiling address is 8f276fff instead of
8f277000. Since this adjustment isn't necessary for the LCDC v2, the
origin ceiling address should be used.
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Due to some potential tweaks for the da850 LCDC (for example: the
required memory bandwith settings) we need a separate compatible
for the IP present on the da850 boards.
Suggested-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Some architectures don't use the common clock framework and don't
implement all the clk interfaces for every clock. This is the case
for da850-lcdk where clk_set_rate() only works for PLL0 and PLL1.
Trying to set the clock rate for the LCDC clock results in -EINVAL
being returned.
As a workaround for that: if the call to clk_set_rate() fails, fall
back to adjusting the clock divider instead. Proper divider value is
calculated by dividing the current clock rate by the required pixel
clock rate in HZ.
This code is based on a hack initially developed internally for
baylibre by Karl Beldan <kbeldan@baylibre.com>.
Tested with a da850-lcdk with an LCD display connected over VGA.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
The ATPX method does not always exist on the dGPU, it may be located at
the iGPU. The parent device of the iGPU is the root port for which
bridge_d3 is false. This accidentally enables the legacy PM method which
conflicts with port PM and prevented the dGPU from powering on.
Ported from amdgpu commit:
drm/amdgpu: fix check for port PM availability
from Peter Wu.
Fixes: d3ac31f3b4 (drm/radeon: fix power state when port pm is unavailable (v2))
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: Peter Wu <peter@lekensteyn.nl>
Cc: <stable@vger.kernel.org> # 4.8+
The ATPX method does not always exist on the dGPU, it may be located at
the iGPU. The parent device of the iGPU is the root port for which
bridge_d3 is false. This accidentally enables the legacy PM method which
conflicts with port PM and prevented the dGPU from powering on.
Fixes: 1db4496f16 ("drm/amdgpu: fix power state when port pm is unavailable")
Reported-and-tested-by: Mike Lothian <mike@fireburn.co.uk>
Signed-off-by: Peter Wu <peter@lekensteyn.nl>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: <stable@vger.kernel.org> # 4.8+
This patch enables the Audio Data and Clock pads to the adv7533 bridge.
Without this patch audio can not be played.
Cc: David Airlie <airlied@linux.ie>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Wolfram Sang <wsa+renesas@sang-engineering.com>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: "Ville Syrjälä" <ville.syrjala@linux.intel.com>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Andy Green <andy@warmcat.com>
Cc: Dave Long <dave.long@linaro.org>
Cc: Guodong Xu <guodong.xu@linaro.org>
Cc: Zhangfei Gao <zhangfei.gao@linaro.org>
Cc: Mark Brown <broonie@kernel.org>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Jose Abreu <joabreu@synopsys.com>
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1480382552-28219-3-git-send-email-john.stultz@linaro.org
This patch adds support to Audio for both adv7511 and adv7533
bridge chips.
This patch was originally from [1] by Lars-Peter Clausen <lars@metafoo.de>
and was adapted by Archit Taneja <architt@codeaurora.org> and
Srinivas Kandagatla <srinivas.kandagatla@linaro.org>.
Then I heavily reworked it to use the hdmi-codec driver. And also
folded in some audio packet initialization done by Andy Green
<andy.green@linaro.org>. So credit to them, but blame to me.
[1] https://github.com/analogdevicesinc/linux/blob/xcomm_zynq/drivers/gpu/drm/i2c/adv7511_audio.c
Cc: David Airlie <airlied@linux.ie>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Wolfram Sang <wsa+renesas@sang-engineering.com>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: "Ville Syrjälä" <ville.syrjala@linux.intel.com>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Andy Green <andy@warmcat.com>
Cc: Dave Long <dave.long@linaro.org>
Cc: Guodong Xu <guodong.xu@linaro.org>
Cc: Zhangfei Gao <zhangfei.gao@linaro.org>
Cc: Mark Brown <broonie@kernel.org>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Jose Abreu <joabreu@synopsys.com>
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Cc: dri-devel@lists.freedesktop.org
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1480382552-28219-2-git-send-email-john.stultz@linaro.org
Add a kernel parameter legancyfb_depth (like the i.MX drm driver)
to control the legancy fbdev depth. Default to the so far hard
coded depth of 24-bit. Currently changing the framebuffer depth
is not possible from user space when using the fbdev emulation
layer... This provides a rudimentary mechanism to change depth
without having to change kernel code.
Signed-off-by: Stefan Agner <stefan@agner.ch>
The separate file fsl_dcu_drm_fbdev.c only initialized fbdev
emulation which is a one-line operation. There is not much more
code on sight which justifies a separate file, hence call the
initialization helper directly from the drv file.
Signed-off-by: Stefan Agner <stefan@agner.ch>
In case of platform_get_irq() failure, let's propagate the real
error code, instead of a 'fake' one.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
devm_ioremap_resource() performs NULL check for the 'res' argument,
so remove the unneeded check.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Make sure that all outputs are disabled before unloading the DRM
driver. Otherwise vblank handling is not shut down properly and
warnings such as this appear:
WARNING: CPU: 0 PID: 540 at drivers/gpu/drm/drm_irq.c:339 drm_vblank_cleanup+0x5c/0x94
Signed-off-by: Stefan Agner <stefan@agner.ch>
Use drm_put_dev to unload the driver before disabling clocks.
Otherwise the driver might read a register during unload which
leads to an external abort.
Signed-off-by: Stefan Agner <stefan@agner.ch>
This could lead to mclk dpm problems on some boards.
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Ack-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Most 5XX targets have GPMU (Graphics Power Management Unit) that
handles a lot of the heavy lifting for power management including
thermal and limits management and dynamic power collapse. While
the GPMU itself is optional, it is usually nessesary to hit
aggressive power targets.
The GPMU firmware needs to be loaded into the GPMU at init time via a
shared hardware block of registers. Using the GPU to write the microcode
is more efficient than using the CPU so at first load create an indirect
buffer that can be executed during subsequent initalization sequences.
After loading the GPMU gets initalized through a shared register
interface and then we mostly get out of its way and let it do
its thing.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Disable the interrupt during the init sequence to avoid having
interrupts fired for errors and other things that we are not
ready to handle while initializing.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The adreno code inherited a silly workaround from downstream
from the bad old days before decent clock control. grp_clk[0]
(named 'src_clk') doesn't actually exist - it was used as a proxy
for whatever the core clock actually was (usually 'core_clk').
All targets should be able to correctly request 'core_clk' and
get the right thing back so zap the anachronism and directly
use grp_clk[0] to control the clock rate.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add helper functions for TYPE4 and TYPE7 ME opcodes that replace
TYPE0 and TYPE3 starting with the A5XX targets.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add a new generic function to write a "64" bit value. This isn't
actually a 64 bit operation, it just writes the upper and lower
32 bit of a 64 bit value to a specified LO and HI register. If
a particular target doesn't support one of the registers it can
mark that register as SKIP and writes/reads from that register
will be quietly dropped.
This can be immediately put in place for the ringbuffer base and
the RPTR address. Both writes are converted to use
adreno_gpu_write64() with their respective high and low registers
and the high register appropriately marked as SKIP for both 32 bit
targets (a3xx and a4xx). When a5xx comes it will define valid target
registers for the 'hi' option and everything else will just work.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add some new functions to manipulate GPU registers. gpu_read64 and
gpu_write64 can read/write a 64 bit value to two 32 bit registers.
For 4XX and older these are normally perfcounter registers, but
future targets will use 64 bit addressing so there will be many
more spots where a 64 bit read and write are needed.
gpu_rmw() does a read/modify/write on a 32 bit register given a mask
and bits to OR in.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
When the GPU hardware init function fails (like say, ME_INIT timed
out) return error instead of blindly continuing on. This gives us
a small chance of saving the system before it goes boom.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
There are very few register accesses in the common code. Cut down
the list of common registers to just those that are used. This
saves const space and saves us the effort of maintaining registers
for A3XX and A4XX that don't exist or are unused.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
For a5xx the gpu is 64b so we need to change iova to 64b everywhere. On
the display side, iova is still 32b so it can ignore the upper bits.
(Although all the armv8 devices have an iommu that can map 64b pa to 32b
iova.)
Signed-off-by: Rob Clark <robdclark@gmail.com>
CEA-861 specifies that the vertical front porch may vary by one or two
lines for specific VICs. Up to now we've only considered a mode to match
the VIC if it matched the shortest possible vertical front porch length
(as that is the variant we store in cea_modes[]). Let's allow our VIC
matching to work with the other timings variants as well so that that
we'll send out the correct VIC if the variant actually used isn't the
one with the shortest vertical front porch.
Cc: Shashank Sharma <shashank.sharma@intel.com>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Adam Jackson <ajax@redhat.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1478177609-16762-2-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
The newly added sound driver depends on SND_SOC_HDMI_CODEC, which in
turn only makes sense when ASoC is enabled, as shown by this warning:
warning: (DRM_MSM && DRM_STI && DRM_MEDIATEK_HDMI && DRM_I2C_NXP_TDA998X && DRM_DW_HDMI_I2S_AUDIO) selects SND_SOC_HDMI_CODEC which has unmet direct dependencies (SOUND && !M68K && !UML && SND && SND_SOC)
Since the audio driver is probably useless without the audio subsystem,
adding a dependency here seems the right solution.
Fixes: 2761ba6c09 ("drm: bridge: add DesignWare HDMI I2S audio support")
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20161125205411.1157522-1-arnd@arndb.de
smatch correctly warns:
drivers/gpu/drm/drm_fb_helper.c:1960 drm_target_preferred() warn: should '1 << i' be a 64 bit type?
drivers/gpu/drm/drm_fb_helper.c:2001 drm_target_preferred() warn: should '1 << i' be a 64 bit type?
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need to call drm_helper_hpd_irq_event() on resume to properly detect
monitor connection / disconnection on some laptops, use hpd_work for
this to avoid deadlocks.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
We need to call drm_helper_hpd_irq_event() on resume to properly detect
monitor connection / disconnection on some laptops. For runtime-resume
(which gets called on resume from normal suspend too) we must call
drm_helper_hpd_irq_event() from a workqueue to avoid a deadlock.
Rename acpi_work to hpd_work, and move it out of the #ifdef CONFIG_ACPI
blocks to make it suitable for generic work.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The new atomic modesetting/pageflip code for nv50+ for
Linux 4.10+ no longer uses pageflip irq's to signal
flip completion. Instead it polls for flip completion
from within a kthread/work queue.
This creates a race between the vblank irq handler
updating the vblank count and timestamp for the
vblank of flip completion, and the kthread's
polling code detecting flip completion and sending
out the flip completion event.
Depending on who executes a few microseconds earlier,
the flip completion event will either contain correct
count/timestamp or a stale count/timestamp from the
previous vblank. This error was observed for about
50% of all executed flips, e.g., observable under DRI2
by the Xorg.log filling with flip handler warning
messages.
Call drm_accurate_vblank_count() before sending
out flip completion events to enforce a vblank
count/ts update for the vblank of flip completion
and avoid stale counts/timestamps.
This fix leads to one redundant call to drm_update_vblank_count
for each completed flip, but no other side effects. On
a ~6 year old Core i7 M620@ 2.67GHz the redundant call
costs about 10 usecs per flip
Successfully tested on GeForce 9500/9600/330M so far.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Previous value really only made sense on armv7 without LPAE. Everything
that supports more than 4g of memory also has iommu's that can map
anything.
Signed-off-by: Rob Clark <robdclark@gmail.com>
In add_components_mdp, we parse the endpoints in MDP output ports
using the helper for_each_endpoint_of_node(). Our function calls
of_node_put() on the endpoint node before we iterate over the
next one. This is already done by the helper, and results in
trying to decrement the refcount twice.
Remove the extra of_node_put calls. This fixes warnings seen when
we try to insert the driver as a module on IFC6410.
Reported-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The mode_config->max_{width,height} is for the maximum size of a fb, not
the max scanout limits (of the layer-mixer). It is legal, and in fact
common, to create a larger fb, only only scan-out a smaller part of it.
For example multi-monitor configurations for x11, or android wallpaper
layer (which is created larger than the screen resolution for fast
scrolling by just changing the src x/y coordinates).
Signed-off-by: Rob Clark <robdclark@gmail.com>
Previously, SMP block allocation was not checked in the plane's
atomic_check() fxn, so we could fail allocation SMP block allocation at
atomic_update() time. Re-work the block allocation to request blocks
during atomic_check(), but not update the hw until committing the atomic
update.
Since SMP blocks allocated at atomic_check() time, we need to manage the
SMP state as part of mdp5_state (global atomic state). This actually
ends up significantly simplifying the SMP management, as the SMP module
does not need to manage the intermediate state between assigning new
blocks before setting flush bits and releasing old blocks after vblank.
(The SMP registers and SMP allocation is not double-buffered, so newly
allocated blocks need to be updated in kms->prepare_commit() released
blocks in kms->complete_commit().)
Signed-off-by: Rob Clark <robdclark@gmail.com>
(re)assign the hw pipes to planes based on required caps, and to handle
situations where we could not modify an in-use plane (ie. SMP block
reallocation).
This means all planes advertise the superset of formats and properties.
Userspace must (as always) use atomic TEST_ONLY step for atomic updates,
as not all planes may be available for use on every frame.
The mapping of hwpipe to plane is stored in mdp5_state, so that state
updates are atomically committed in the same way that plane/etc state
updates are managed. This is needed because the mdp5_plane_state keeps
a pointer to the hwpipe, and we don't want global state to become out
of sync with the plane state if an atomic update fails, we hit deadlock/
backoff scenario, etc. The use of state_lock keeps multiple parallel
updates which both re-assign hwpipes properly serialized.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add basic state duplication/apply mechanism. Following commits will
move actual global hw state into this.
The state_lock allows multiple concurrent updates to proceed as long as
they don't both try to alter global state. The ww_mutex mechanism will
trigger backoff in case of deadlock between multiple threads trying to
update state.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Split out the hardware pipe specifics from mdp5_plane. To start, the hw
pipes are statically assigned to planes, but next step is to assign the
hw pipes during plane->atomic_check() based on requested caps (scaling,
YUV, etc). And then hw pipe re-assignment if required if required SMP
blocks changes.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Just use plane->name now that it is a thing. In a following patch, once
we dynamically assign hw pipes to planes, it won't make sense to name
planes the way we do, so this also partly reduces churn in following
patch.
Signed-off-by: Rob Clark <robdclark@gmail.com>
We can do this all from mdp5_plane_complete_commit(), so simplify things
a bit and drop mdp5_plane_complete_flip().
Signed-off-by: Rob Clark <robdclark@gmail.com>
Plane's (pipes) can be assigned dynamically with atomic, so it doesn't
make much sense to name the pipe after it's primary plane.
Signed-off-by: Rob Clark <robdclark@gmail.com>
These are really plane-id's, not crtc-id's. Only connection to CRTCs is
that they are used as primary-planes.
Current name is just legacy from when we only supported RGB/primary
planes. Lets pick a better name now.
Signed-off-by: Rob Clark <robdclark@gmail.com>
We can have various combinations of 64b and 32b address space, ie. 64b
CPU but 32b display and gpu, or 64b CPU and GPU but 32b display. So
best to decouple the device iova's from mmap offset.
Signed-off-by: Rob Clark <robdclark@gmail.com>
If fb dimensions are larger than what can be scanned out, but the src
dimensions are not, the hw can still handle this. So clip.
Signed-off-by: Rob Clark <robdclark@gmail.com>
If the bottom-most layer is not fullscreen, we need to use the BASE
mixer stage for solid fill (ie. MDP5_CTL_BLEND_OP_FLAG_BORDER_OUT). The
blend_setup() code pretty much handled this already, we just had to
figure this out in _atomic_check() and assign the stages appropriately.
Also fix the case where there are zero enabled planes, where we also
need to enable BORDER_OUT.
Signed-off-by: Rob Clark <robdclark@gmail.com>
When CONFIG_PM_SLEEP is disabled, we get a harmless warning
drm/hisilicon/hibmc/hibmc_drm_drv.c:115:12: error: ‘hibmc_pm_resume’ defined but not used [-Werror=unused-function]
drm/hisilicon/hibmc/hibmc_drm_drv.c:97:12: error: ‘hibmc_pm_suspend’ defined but not used [-Werror=unused-function]
Marking the functions as __maybe_unused avoids the warning without
having to add an #ifdef.
Fixes: 5e0df3a08f ("drm/hisilicon/hibmc: Add hisilicon hibmc drm master driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20161124163107.3914495-1-arnd@arndb.de
The drm_dev_alloc() function returns error pointers. It never returns
NULLs.
Fixes: 5e0df3a08f ("drm/hisilicon/hibmc: Add hisilicon hibmc drm master driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20161124113545.GP17225@mwanda
This branch include patches of fixing a typo, accurate dsi frame rate,
and fixing null pointer dereference.
* 'mediatek-drm-fixes-2016-11-24' of https://github.com/ckhu-mediatek/linux.git-tags:
drm/mediatek: fix null pointer dereference
drm/mediatek: fixed the calc method of data rate per lane
drm/mediatek: fix a typo of DISP_OD_CFG to OD_RELAYMODE
Need to be careful to release struct_mutext when request alloc
failed and take consistent handling for return status as with
normal go out path. Ensure to check correct workload request in
complete path too.
v2: Add Fixes note
Fixes: 90d27a1b18 ("drm/i915/gvt: fix deadlock in workload_thread")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Pei Zhang <pei.zhang@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Free memory mapping, if hdmi_probe is not successful.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
These updates:
* improve the robustness of the driver wrt races
* improve the compliance for sending infoframes and audio
* re-organise the function order in the driver to group like functions
together. (This unfortunately causes a conflict with the change in
drm-misc, but it should be trivial to solve, although it looks more
scarey than it really is - sfr has already sent two reports about
this, one earlier today.)
* simplify tda998x_audio_get_eld and DPMS handling
* power down sections of the chip that we never use
* add some initial preparation for supporting the CEC driver
* 'drm-tda998x-devel' of git://git.armlinux.org.uk/~rmk/linux-arm:
drm/i2c: tda998x: fix spelling mistake
drm/i2c: tda998x: allow sharing of the CEC device accesses
drm/i2c: tda998x: allow interrupt to be shared
drm/i2c: tda998x: power down pre-filter and color conversion
drm/i2c: tda998x: switch to boolean is_on
drm/i2c: tda998x: remove complexity from tda998x_audio_get_eld()
drm/i2c: tda998x: group audio functions together
drm/i2c: tda998x: separate connector initialisation
drm/i2c: tda998x: group connector functions and funcs together
drm/i2c: tda998x: move and rename tda998x_encoder_set_config()
drm/i2c: tda998x: correct function name in comments
drm/i2c: tda998x: only enable audio if supported by sink
drm/i2c: tda998x: only configure infoframes and audio if supported
drm/i2c: tda998x: avoid race when programming audio
drm/i2c: tda998x: avoid racy access to mode clock
drm/i2c: tda998x: avoid race in tda998x_encoder_mode_set()
drm/i2c: tda998x: move audio mutex initialisation
Building on top of the MALI change previously merged, these changes:
* add tracing support for overlay updates
* refactor some of the plane support code
* de-midlayer the driver
* cleanups from other folk reviewing the code
* 'drm-armada-devel' of git://git.armlinux.org.uk/~rmk/linux-arm:
drm/armada: fix NULL pointer comparison warning
drm/armada: use DRM_FB_HELPER_DEFAULT_OPS for fb_ops
drm/armada: remove some dead code
drm/armada: mark symbols static where possible
drm/armada: de-midlayer armada
drm/armada: use common helper for plane base address
drm/armada: move setting primary plane position to armada_drm_primary_set()
drm/armada: split out primary plane update
drm/armada: move plane state to struct armada_plane
drm/armada: clean up armada_drm_plane_work_run()
drm/armada: add tracing support
Current dw-hdmi is supporting sound via AHB bus, but it has
I2S audio feature too. This patch adds I2S audio support to dw-hdmi.
This HDMI I2S is supported by using ALSA SoC common HDMI encoder
driver.
Tested-by: Jose Abreu <joabreu@synopsys.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/8737j2bxba.wl%kuninori.morimoto.gx@renesas.com
Use the color_adjust callback when reserving a node to check if
inserting a node into this hole requires any additional space, and so if
that space then conflicts with an existing allocation.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20161123141118.23876-2-chris@chris-wilson.co.uk
Some clients would like to iterate over every node within a certain
range. Make a nice little macro for them to hide the mixing of the
rbtree search and linear walk.
v2: Blurb
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20161123141118.23876-1-chris@chris-wilson.co.uk
The probe function requests the interrupt before initializing
the ddp component. Which leads to a null pointer dereference at boot.
Fix this by requesting the interrput after all components got
initialized properly.
Fixes: 119f517362 ("drm/mediatek: Add DRM Driver for Mediatek SoC
MT8173.")
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Change-Id: I57193a7ab554dfb37c35a455900689333adf511c
Tune dsi frame rate by pixel clock, dsi add some extra signal (i.e.
Tlpx, Ths-prepare, Ths-zero, Ths-trail,Ths-exit) when enter and exit LP
mode, those signals will cause h-time larger than normal and reduce FPS.
So need to multiply a coefficient to offset the extra signal's effect.
coefficient = ((htotal*bpp/lane_number)+Tlpx+Ths_prep+Ths_zero+
Ths_trail+Ths_exit)/(htotal*bpp/lane_number)
Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
If we want to set the hardware OD to relay mode,
we have to set DISP_OD_CFG register rather than
OD_RELAYMODE; otherwise, the system will access
the wrong address.
Change-Id: Ifb9bb4caa63df906437d48b5d5326b6d04ea332a
Fixes: 7216436420 ("drm/mediatek: set mt8173 dithering function")
Cc: stable@vger.kernel.org # v4.9+
Signed-off-by: Bibby Hsieh <bibby.hsieh@mediatek.com>
Acked-by: CK Hu <ck.hu@mediatek.com>
For 64bit bar while reading the higher 32bit the value should be returned
directly.
In the current implementation the higher 32bit value was discarded and not
written to the cfg space of vgpu which lead to an incorrect bar size.
Signed-off-by: Xiaoguang Chen <xiaoguang.chen@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
A late issue discovered by Russell King while testing his setup on Juno.
* 'for-upstream/hdlcd' of git://linux-arm.org/linux-ld:
drm/arm: hdlcd: fix plane base address update
one small powerplay fix and one regression fix for older PX systems and d3cold
* 'drm-fixes-4.9' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: fix power state when port pm is unavailable (v2)
drm/amdgpu: fix power state when port pm is unavailable
drm/amd/powerplay: avoid out of bounds access on array ps.
UVD 5 and newer do not have the same placement limitations
as older chips, so skip the first pass since it's just
overhead on chips where we don't have to force placement.
v2: fix inverted logic
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Same code duplicated in both functions.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch is used for virtualization support. In virtualization,
only SMU manager is needed, DPM should be disabled. This is a
use case for commit 2f9346b6f984
("drm/amdgpu/powerplay: pp module only enable smu when dpm disabled.")
Signed-off-by: Trigger Huang <trigger.huang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Doesn't make much sense to have the same functionality twice.
v2: rebase on dma_fence renaming
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Drop this whole reserve/unreserve dance, just lock the
reservation object manually when creating the BO.
v2: rebase on dma_fence renaming
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Manually checking why a function could fail is not a good idea
if you can just check the functions return code.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The mem start is relative to the domain in the address space, so this
worked only when VRAM was mapped at offset 0.
It also didn't handled multiple drm_mm_nodes for split VRAM.
v2: rebase on dma_fence renaming
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Not used any more.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It can be the case that upon GPU page faults we start trashing
the logs, and so let us ratelimit here to avoid that.
V2. Fix issue where calling dev_err_ratelimited separately for
each line means that some lines corresponding to a single
VM fault may or may not appear depending on the rate.
- Michel Dänzer.
Reviewed-by: Christian König <christian.koenig@amd.com> (v1)
Signed-off-by: Edward O'Callaghan <funfunctor@folklore1984.net>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Edward O'Callaghan <funfunctor@folklore1984.net>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Port of SI DCE v6 over to new AMDGPU headers. Tested on a
Tahiti with GNOME through various hot plugs/rotations/sizes/fullscreen/windowed and
staging drm/xf86-video-amdgpu.
(v2) Re-factored to remove formatting changes to si_enums.h
as well rename various defines.
(v3) Rebase on upstream
Signed-off-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
when shadowing enabled, tesselation app will trigger
vm fault because below three tesselation registers:
VGT_TF_RING_SIZE__CI__VI,
VGT_HS_OFFCHIP_PARAM__CI__VI,
VGT_TF_MEMORY_BASE__CI__VI,
need to be programed after vgt-flush.
Tesselation picture vm fault disappeared after vgt-flush
introduced.
v2:implement vgt-flush for CI & SI.
v3:move vgt flush inside of cntx_cntrl
v4:count vgt flush in frame_size
v5:squash in typo fix
Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
sw clockgate was used on uvd6.0.
when uvd is idle, we gate the uvd clock.
when decode, we ungate the uvd clock.
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When PCIe port PM is not enabled (system BIOS is pre-2015 or the
pcie_port_pm=off parameter is set), legacy ATPX PM should still be
marked as supported. Otherwise the GPU can fail to power on after
runtime suspend. This affected a Dell Inspiron 5548.
Ideally the BIOS date in the PCI core is lowered to 2013 (the first year
where hybrid graphics platforms using power resources was introduced),
but that seems more risky at this point and would not solve the
pcie_port_pm=off issue.
v2: agd: fix typo
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=98505
Signed-off-by: Peter Wu <peter@lekensteyn.nl>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: <stable@vger.kernel.org> # 4.8+
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
When PCIe port PM is not enabled (system BIOS is pre-2015 or the
pcie_port_pm=off parameter is set), legacy ATPX PM should still be
marked as supported. Otherwise the GPU can fail to power on after
runtime suspend. This affected a Dell Inspiron 5548.
Ideally the BIOS date in the PCI core is lowered to 2013 (the first year
where hybrid graphics platforms using power resources was introduced),
but that seems more risky at this point and would not solve the
pcie_port_pm=off issue.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=98505
Reported-and-tested-by: Nayan Deshmukh <nayan26deshmukh@gmail.com>
Signed-off-by: Peter Wu <peter@lekensteyn.nl>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: <stable@vger.kernel.org> # 4.8+
Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Initiate param.primary to 1. We should be primary currently.
Signed-off-by: Du, Changbin <changbin.du@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
We now pass the device to the debug messages, but on non-x86,
this is an invalid pointer in vga_arb_device_init:
drivers/gpu/vga/vgaarb.c: In function 'vga_arb_device_init':
drivers/gpu/vga/vgaarb.c:1467:4: error: 'dev' may be used uninitialized in this function [-Werror=maybe-uninitialized]
This moves the initialization of the dev pointer outside of the
architecture #ifdef.
Fixes: a75d68f621 ("vgaarb: Use dev_printk() when possible")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20161122143445.1896558-1-arnd@arndb.de
While testing HDMI with Xorg on the Juno board, I find that when Xorg
starts up or shuts down, the display is shifted significantly to the
right and wrapped in the active region. (No sync bars are visible.)
The timings are correct, it behaves as if the start address has been
shifted many pixels _into_ the framebuffer.
This occurs whenever the display mode size is changed - using xrandr
in Xorg shows that changing the resolution triggers the problem
almost every time, but changing the refresh rate does not.
Using devmem2 to disable and re-enable the HDLCD resolves the issue,
and repeated disable/enable cycles do not make the issue re-appear.
Further debugging shows that we try to update the controller
configuration while enabled.
Alwys ensure that the HDLCD is disabled prior to updating the
controller timings, and use drm_crtc_vblank_off()/drm_crtc_vblank_on()
so that DRM knows whether it can expect vblank interrupts.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
I totally butcherd the job on typing the kernel-doc for these, and no
one realized. Noticed by Russell. Maarten has a more complete approach
to this confusion, by making it more explicit what the new/old state
is, instead of this magic switching behaviour.
v2:
- Liviu pointed out that wait_for_fences is even more magic. Leave
that as @state, and document @pre_swap better.
- While at it, patch in header for the reference section.
- Fix spelling issues Russell noticed.
v3: Fix up the @pre_swap note (Liviu): Also s/synchronous/blocking/,
since async flip is something else than non-blocking.
Cc: Liviu Dudau <liviu.dudau@arm.com>
Reported-by: Russell King - ARM Linux <linux@armlinux.org.uk>
Cc: Russell King - ARM Linux <linux@armlinux.org.uk>
Fixes: 9f2a7950e7 ("drm/atomic-helper: nonblocking commit support")
Cc: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Tomeu Vizoso <tomeu.vizoso@gmail.com>
Cc: Daniel Stone <daniels@collabora.com>
Reviewed-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20161121171802.24147-1-daniel.vetter@ffwll.ch
Cleanup the debugfs entries created by
commit 6559c901cb: drm/atomic: add debugfs file to dump out atomic state
when the driver's minor gets un-registered. Without it, DRM drivers
compiled as modules cannot be rmmod-ed and modprobed again.
Tested-by: Brian Starkey <brian.starkey@arm.com>
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20161117114129.2627-1-Liviu.Dudau@arm.com
Fixes: 6559c901cb ("drm/atomic: add debugfs file to dump out atomic state")
hibmc drm driver for hisilicon.
* tag 'drm-hisilicon-next-2016-11-17' of http://github.com/zourongrong/linux:
MAINTAINERS: Update HISILICON DRM entries
drm/hisilicon/hibmc: Add support for vblank interrupt
drm/hisilicon/hibmc: Add support for VDAC
drm/hisilicon/hibmc: Add support for display engine
drm/hisilicon/hibmc: Add support for frame buffer
drm/hisilicon/hibmc: Add video memory management
drm/hisilicon/hibmc: Add hisilicon hibmc drm master driver
Currently we only clflush the scanout if it is in the CPU domain. Also
flush if we have a pending CPU clflush. We also want to treat the
dirtyfb path similar, and flush any pending writes there as well.
v2: Only send the fb flush message if flushing the dirt on flip
v3: Make flush-for-flip and dirtyfb look more alike since they serve
similar roles as end-of-frame marker.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> #v2
Link: http://patchwork.freedesktop.org/patch/msgid/20161118211747.25197-1-chris@chris-wilson.co.uk
On the DMA mapping error path, sg may be NULL (it has already been
marked as the last scatterlist entry), and we should avoid dereferencing
it again.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: e227330223 ("drm/i915: avoid leaking DMA mappings")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Imre Deak <imre.deak@intel.com>
Cc: stable@vger.kernel.org
Link: http://patchwork.freedesktop.org/patch/msgid/20161114112930.2033-1-chris@chris-wilson.co.uk
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
When gathering the pages from our backing storage we expect get_pages()
to either give us our sg_table or an err ptr. However when gathering our
fake pages for stolen memory we may return NULL in the event of a
failure. To prevent any funny business we should therefore return the
proper err ptr value.
Fixes: 03ac84f183 ("drm/i915: Pass around sg_table to get_pages/put_pages backend")
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1479488536-6168-1-git-send-email-matthew.auld@intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Since we can retire requests from multiple paths, we cannot assume that
i915_gem_retire_requests() is the sole path on which we can transition
to gt.active_requests == 0. A consequence of this is that we would skip
the function if we had already retired all the requests and not
scheduled the idle worker.
This is fallout from changing the routine from considering active_engines
(for which it was the only consumer) to active_requests.
v2: Move kicking the idle working to i915_gem_request_retire() otherwise
we could postpone the idle callback everytime we called retire_requests
even though we did no work.
v3: We only need to move the idle work kicking!
v4: Drop the BUG_ON(!awake) as we may be called from the shrinker in the
middle of constructing a request before we have marked the device awake.
v5: Add a BUG_ON() for active_requests underflow upon retirement (Joonas)
Fixes: 28176ef4cf ("drm/i915: Reserve space in the global seqno during request allocation")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20161115164620.17185-1-chris@chris-wilson.co.uk
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
I tried to avoid having to track the write for every VMA by only
tracking writes to the ggtt. However, for the purposes of frontbuffer
tracking this is insufficient as we need to invalidate around writes not
just to the the ggtt but all aliased ppgtt views of the framebuffer. By
moving the critical section to the object and only doing so for
framebuffer writes we can reduce the tracking even further by only
watching framebuffers and not vma.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20161116190704.5293-1-chris@chris-wilson.co.uk
Tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Use dev_printk() when possible. This makes messages more consistent with
other device-related messages and, in some cases, adds useful information.
This changes messages like this:
vgaarb: failed to allocate pci device
vgaarb: setting as boot device: PCI:0000:01:00.0
vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
vgaarb: bridge control possible 0000:01:00.0
to this:
pci 0000:01:00.0: vgaarb: failed to allocate VGA arbiter data
pci 0000:01:00.0: vgaarb: setting as boot VGA device
pci 0000:01:00.0: vgaarb: VGA device added: decodes=io+mem,owns=io+mem,locks=none
pci 0000:01:00.0: vgaarb: bridge control possible
No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20161117174758.16810.67625.stgit@bhelgaas-glaptop.roam.corp.google.com
There's a really big pile of additional connector properties, a lot of
them standardized. But they're all for specific outputs (panels, TV,
scaling, ...) so I left them out for now since this is enough for a
start.
I typed this to give Manasi a place to add her new link status
property documentation.
v2: forgot to git add all the bits (Manasi).
v3: Be more epxlicit about integrated tiled panels (Archit)
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Archit Taneja <architt@codeaurora.org>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20161117085648.26646-1-daniel.vetter@ffwll.ch
i915 misc fixes.
* tag 'drm-intel-fixes-2016-11-17' of ssh://git.freedesktop.org/git/drm-intel:
drm/i915: Assume non-DP++ port if dvo_port is HDMI and there's no AUX ch specified in the VBT
drm/i915: Refresh that status of MST capable connectors in ->detect()
drm/i915: Grab the rotation from the passed plane state for VLV sprites
drm/i915: Mark CPU cache as dirty when used for rendering
Trivial fix to spelling mistake "configutation" to "configuration"
in dev_err message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
cec_read() is non-atomic in the presence of other I2C bus transactions
to the same device. This presents a problem when we add support for
the TDA9950 CEC engine part - both drivers can be trying to access the
device.
Avoid the inherent problems by switching to i2c_transfer() instead,
which allows us to perform more than one bus transaction atomically.
As this means we will be using I2C transactions rather than SMBUS, we
have to check that the host supports I2C functionality.
Tested-by: Brian Starkey <brian.starkey@arm.com>
Reviewed-by: Brian Starkey <brian.starkey@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Some TDA998x contain several different I2C devices - there is the HDMI
encoder, and there is a TDA9950 CEC engine. These two share the same
interrupt signal.
In order to allow a driver for the CEC engine to work, we need to be
able to share the interrupt with the CEC driver, so convert the handler
and registration to allow this to happen.
Tested-by: Brian Starkey <brian.starkey@arm.com>
Reviewed-by: Brian Starkey <brian.starkey@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Disabling the pre-filter block of the TDA998x saves 40mW and the colour
conversion block saves 15mW. As we always disable these two blocks, we
can power these sections of the chip down to save 55mW of unnecessary
power consumption.
Tested-by: Brian Starkey <brian.starkey@arm.com>
Reviewed-by: Brian Starkey <brian.starkey@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Rather than storing the DPMS mode (which will always be on or off) use a
boolean to store this instead.
Tested-by: Robin Murphy <robin.murphy@arm.com>
Tested-by: Jon Medhurst <tixy@linaro.org>
Acked-by: Jon Medhurst <tixy@linaro.org>
Tested-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
tda998x_audio_get_eld() is needlessly complex - the connector associated
with the encoder is always our own priv->connector. Remove this
complexity, but ensure that there are no races when copying out the ELD.
Tested-by: Jon Medhurst <tixy@linaro.org>
Acked-by: Jon Medhurst <tixy@linaro.org>
Tested-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Group the TDA998x audio functions together rather than split between
two different locations in the file, keeping like code together.
Tested-by: Jon Medhurst <tixy@linaro.org>
Acked-by: Jon Medhurst <tixy@linaro.org>
Tested-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Separate out the connector initialisation from the rest of the drivers
initialisation.
Tested-by: Robin Murphy <robin.murphy@arm.com>
Tested-by: Jon Medhurst <tixy@linaro.org>
Acked-by: Jon Medhurst <tixy@linaro.org>
Tested-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Group the TDA998x connector functions and funcs structures together
before the encoder support, rather than scattered amongst the rest of
the file. This keeps like code together.
Tested-by: Robin Murphy <robin.murphy@arm.com>
Tested-by: Jon Medhurst <tixy@linaro.org>
Acked-by: Jon Medhurst <tixy@linaro.org>
Tested-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
The naming of tda998x_encoder_set_config() is a left-over from when
TDA998x was a slave encoder. Since this is part of the initialisation,
drop the _encoder from the name, and move it near tda998x_bind().
Tested-by: Robin Murphy <robin.murphy@arm.com>
Tested-by: Jon Medhurst <tixy@linaro.org>
Acked-by: Jon Medhurst <tixy@linaro.org>
Tested-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Correct two references to tda998x_connector_get_modes() which were
incorrectly referring to tda998x_encoder_get_modes().
Tested-by: Robin Murphy <robin.murphy@arm.com>
Tested-by: Jon Medhurst <tixy@linaro.org>
Acked-by: Jon Medhurst <tixy@linaro.org>
Tested-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Check for audio support by the attached sink by consulting the EDID
prior to enabling audio over the TMDS link. We must consult the EDID
after calling drm_helper_probe_single_connector_modes(), as this can
use an override EDID, or load a replacement EDID.
Tested-by: Jon Medhurst <tixy@linaro.org>
Acked-by: Jon Medhurst <tixy@linaro.org>
Tested-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
The CEA 861B specification indicates the situations when we are able to
send each infoframe based on the version of the EDID's CEA extension.
Update the tda998x driver to follow the CEA specification wrt sending
of infoframes.
Since we only support the generation of AVI version 2, this limits us
to CEA extension version 3, so we treat CEA extension version 2 as
CEA 861 (no infoframes, no audio.)
Tested-by: Robin Murphy <robin.murphy@arm.com>
Tested-by: Jon Medhurst <tixy@linaro.org>
Acked-by: Jon Medhurst <tixy@linaro.org>
Tested-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Avoid a race between programming audio and an in-progress mode set.
A mode set is complex, and disables the ability to send infoframes
to the sink, and is disruptive to audio - we have to mute the audio
FIFO while doing a mode set.
If an attempt is made to start up the audio side, we will undo the
audio FIFO mute before the mode set has completed.
Move the lock so that we prevent audio interfering with an in-progress
mode set.
Tested-by: Jon Medhurst <tixy@linaro.org>
Acked-by: Jon Medhurst <tixy@linaro.org>
Tested-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Avoid a racy access to the mode clock by storing the current mode clock
during a mode set under the audio mutex. This allows us to access it
from the audio path in a safe way.
Tested-by: Jon Medhurst <tixy@linaro.org>
Acked-by: Jon Medhurst <tixy@linaro.org>
Tested-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
As priv->audio_params can now be changed at run time, we need to be more
careful about how we deal with a mode set. We must take the audio lock
while checking if there's a valid audio configuration.
However, it's slightly worse than that - during mode set, we mute the
audio, and it must not be unmuted until we have finished the mode set.
It is possible that the audio side may start while a mode set is in
progress, so take the audio_mutex lock around the whole mode setting
procedure.
Tested-by: Jon Medhurst <tixy@linaro.org>
Acked-by: Jon Medhurst <tixy@linaro.org>
Tested-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
We will need the audio mutex initialised in all cases, so lets move this
to be early, rather than only being initialised for the DT case.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
We already have an i915_address_space_init, so for symmetry we should
also have a _fini, plus we already open code it twice. This then also
fixes a bug where we leak the timeline for the ggtt vm.
v2: don't forget about the struct_mutex for the ggtt path.
Fixes: 80b204bce8 ("drm/i915: Enable multiple timelines")
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20161117210411.14044-1-chris@chris-wilson.co.uk
We should never be called via obj->ops->release() on anything other than
a fully formed stolen object, so raise that to an assert. In the process
tidy up a comment and variable no longer used outside of a conditional
BUG.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20161117155846.4631-1-chris@chris-wilson.co.uk
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Kernel pointer does not sound like an useful thing to log and
pipe name is already contained in the crtc name.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
We don't spam the debug when we create a normal object, nor when we
allocate their pages. Yet we do for stolen objects, and since these are
quite frequently used (at least once per context), the resulting spam
floods the dmesg in CI.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
We use DRM_DEBUG() when reporting on user actions, to try and keep
intentional errors out of the CI dmesg. Demote the debug from
i915_gem_open() similarly so that it is only apparent with drm.debug & 1
like its brethren.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20161109104507.21228-1-chris@chris-wilson.co.uk
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
It looks to me skl_update_scaler will already log interesting
debug messages when the state transitions or there is an error.
In this case it feels we can remove the two unconditional
debug messages which happen immediately before calling
skl_update_scaler. This way we get rid of the sole debug
message when switching virtual terminals for example.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1479376805-5087-1-git-send-email-tvrtko.ursulin@linux.intel.com
Plus a trickle of function prototype changes.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
And as usual a little bit of cascaded function prototype changes.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
A bunch of source files with just a few instances of the
incorrect INTEL_INFO use.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
And a little bit of function prototype changes.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
And a little bit of function prototype changes.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
And a little bit of cascaded function prototype changes.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
And a little bit of cascaded function prototype changes.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
And a little bit of cascaded function prototype changes.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Started with removing INTEL_INFO(dev) and cascaded into a quite
big trickle of function prototype changes. Still, I think it is
for the better.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Plus a small cascade of function prototype changes.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
From Zhenyu Wang:
gvt-next-2016-11-17
- Fix lock order issue found in guest stress test
- Fix several MMIO handlers to correct behavior
- Fix crash for vgpu execlist reset and memleak
- Fix a possible conflict for unresolved vfio mdev dependency
- other misc fixes
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Tvrtko needs
commit b3c11ac267
Author: Eric Engestrom <eric@engestrom.ch>
Date: Sat Nov 12 01:12:56 2016 +0000
drm: move allocation out of drm_get_format_name()
to be able to apply his patches without conflicts.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Commit 0dd356bb6f ("drm/i915: Eliminate Gen9 special case")
accidentaly dropped a MMIO range between 0xc000 to 0xcfff out
of the blitter forcewake domain. Fix it.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Fixes: 0dd356bb6f ("drm/i915: Eliminate Gen9 special case")
Reported-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1479373363-16528-1-git-send-email-tvrtko.ursulin@linux.intel.com
We've overlooked adding DSI panels to the front of the connector
list. This seems to be the right thing to do, and I suspect this might
fix some issues, although I currently have no evidence to support this.
v2: also git add the comment change
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1479378548-32695-1-git-send-email-jani.nikula@intel.com
It has been suggested that having per-plane modifiers is making life
more difficult for userspace, so let's just retire modifier[1-3] and
use modifier[0] to apply to the entire framebuffer.
Obviosuly this means that if individual planes need different tiling
layouts and whatnot we will need a new modifier for each combination
of planes with different tiling layouts.
For a bit of extra backwards compatilbilty the kernel will allow
non-zero modifier[1+] but it require that they will match modifier[0].
This in case there's existing userspace out there that sets
modifier[1+] to something non-zero with planar formats.
Mostly a cocci job, with a bit of manual stuff mixed in.
@@
struct drm_framebuffer *fb;
expression E;
@@
- fb->modifier[E]
+ fb->modifier
@@
struct drm_framebuffer fb;
expression E;
@@
- fb.modifier[E]
+ fb.modifier
Cc: Kristian Høgsberg <hoegsberg@gmail.com>
Cc: Ben Widawsky <benjamin.widawsky@intel.com>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Tomeu Vizoso <tomeu@tomeuvizoso.net>
Cc: dczaplejewicz@collabora.co.uk
Suggested-by: Kristian Høgsberg <hoegsberg@gmail.com>
Acked-by: Ben Widawsky <ben@bwidawsk.net>
Acked-by: Daniel Stone <daniels@collabora.com>
Acked-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1479295996-26246-1-git-send-email-ville.syrjala@linux.intel.com
This is essentially the same thing as duplicating DIDL now that the
connector list has the ACPI device IDs.
Cc: Peter Wu <peter@lekensteyn.nl>
Cc: Rainer Koenig <Rainer.Koenig@ts.fujitsu.com>
Cc: Jan-Marek Glogowski <glogow@fbihome.de>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Marcos Paulo de Souza <marcos.souza.org@gmail.com>
Cc: Paolo Stivanin <paolostivanin@fastmail.fm>
Tested-by: Rainer Koenig <Rainer.Koenig@ts.fujitsu.com>
Tested-by: Paolo Stivanin <paolostivanin@fastmail.fm>
Tested-by: Marcos Paulo de Souza <marcos.souza.org@gmail.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/ea0a052fa99a4cb56b559a815866434bcfef853d.1479295490.git.jani.nikula@intel.com
The graphics driver is supposed to define the DIDL, which are used for
_DOD, not the BIOS. Restore that behaviour.
This is basically a revert of
commit 3143751ff5
Author: Zhang Rui <rui.zhang@intel.com>
Date: Mon Mar 29 15:12:16 2010 +0800
drm/i915: set DIDL using the ACPI video output device _ADR method return.
which went out of its way to cater to a specific BIOS, setting up DIDL
based on _ADR method. Perhaps that approach worked on that specific
machine, but on the machines I checked the _ADR method invents the
device identifiers out of thin air if DIDL has not been set. The source
for _ADR is also supposed to be the DIDL set by the driver, not the
other way around.
With this, we'll also limit the number of outputs to what the driver
actually has.
A side effect of this change is that the DIDL, and by proxy CADL, will
be initialized in the order of the connector list. That, in turn, has
internal panels in front, ensuring they're included in the DIDL and CADL
lists. Hopefully this ensures the BIOS does not block backlight hotkey
events, thinking the internal panel is off.
v2: do not set ACPI_DEVICE_ID_SCHEME in the device id (Peter Wu)
v3: Rebase
Cc: Peter Wu <peter@lekensteyn.nl>
Cc: Rainer Koenig <Rainer.Koenig@ts.fujitsu.com>
Cc: Jan-Marek Glogowski <glogow@fbihome.de>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Marcos Paulo de Souza <marcos.souza.org@gmail.com>
Cc: Paolo Stivanin <paolostivanin@fastmail.fm>
Tested-by: Rainer Koenig <Rainer.Koenig@ts.fujitsu.com>
Tested-by: Paolo Stivanin <paolostivanin@fastmail.fm>
Tested-by: Marcos Paulo de Souza <marcos.souza.org@gmail.com>
Reviewed-and-tested-by: Peter Wu <peter@lekensteyn.nl>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/9660d29cf310c17bbf4d58c0e09d5b047446e2d5.1479295490.git.jani.nikula@intel.com
Some dumb VGA DACs are active components which require external power.
Add support for specifying a regulator as its power supply.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20161116154232.872-2-wens@csie.org
For a single_port_submission context, GVT expects that it can only be
submitted to port 0, and there shouldn't be any other context in port 1
at the same time. This is required by GVT-g context to have an opportunity
to save/restore some non-hw context render registers.
This patch is to workaround GVT-g.
v2: optimized code by following Chris's advice, and added more comments to
explain the patch.
v3: followed the coding style.
Signed-off-by: Min He <min.he@intel.com>
Reviewed-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1479305104-17049-1-git-send-email-min.he@intel.com
Instead of partially depending on vfio pin/unpin pages interface if
mdev is available, which would result in failure if vfio is not
on. But replace with a wrapper which need to be fixed till mdev
support got fully merged.
Cc: Jike Song <jike.song@intel.com>
Cc: Xiaoguang Chen <xiaoguang.chen@intel.com>
Reviewed-by: Xiaoguang Chen <Xiaoguang.chen@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Looking at the ioctl permission checks I noticed that it's impossible
to import gem buffers into a control nodes, and fd2handle/handle2fd
also don't work, so no joy with dma-bufs.
The only way to do anything with a control node is by drawing stuff
into a dumb buffer and displaying that. I suspect control nodes are an
entirely unused thing, and a cursory check shows that there does not
seem to be any callers of drmOpenControl nor of the other drmOpen
functions using DRM_MODE_CONTROL.
Since I don't like dead uabi, let's remove it. But since this would be
a really big change I think it's better to start out small by simply
not registering anything. We can garbage-collect the dead code later
on, once we're sure it's really not used anywhere.
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20161028081050.1042-1-daniel.vetter@ffwll.ch
Add vblank interrupt.
Signed-off-by: Rongrong Zou <zourongrong@gmail.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Xinliang Liu <xinliang.liu@linaro.org>
Acked-by: Sean Paul <seanpaul@chromium.org>
VDAC(Video Digital-to-Analog converter) converts the RGB diaital data
stream from DE to VGA analog signals.
Signed-off-by: Rongrong Zou <zourongrong@gmail.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Xinliang Liu <xinliang.liu@linaro.org>
Acked-by: Sean Paul <seanpaul@chromium.org>
Add display engine function, crtc/plane is initialized here.
Signed-off-by: Rongrong Zou <zourongrong@gmail.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Xinliang Liu <xinliang.liu@linaro.org>
Acked-by: Sean Paul <seanpaul@chromium.org>
Add support for fbdev and kms fb management.
Signed-off-by: Rongrong Zou <zourongrong@gmail.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Xinliang Liu <xinliang.liu@linaro.org>
Acked-by: Sean Paul <seanpaul@chromium.org>
Hibmc have 32m video memory which can be accessed through PCIe by host,
we use ttm to manage these memory.
Signed-off-by: Rongrong Zou <zourongrong@gmail.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Xinliang Liu <xinliang.liu@linaro.org>
Acked-by: Sean Paul <seanpaul@chromium.org>
Add DRM master driver for Hisilicon Hibmc SoC which used for
Out-of-band management. Blow is the general hardware connection,
both the Hibmc and the host CPU are on the same mother board.
+----------+ +----------+
| | PCIe | Hibmc |
|host CPU( |<----->| display |
|arm64,x86)| |subsystem |
+----------+ +----------+
Signed-off-by: Rongrong Zou <zourongrong@gmail.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Xinliang Liu <xinliang.liu@linaro.org>
Acked-by: Sean Paul <seanpaul@chromium.org>
We no longer cater for pre-production revisions of Skylake.
Fixes: d4362225e8 ("drm/i915/gvt: update misc ctl regs base on stepping info")
Cc: Ping Gao <ping.a.gao@intel.com>
Cc: Zhenyu Wang <zhenyuw@linux.intel.com>
Cc: Zhi Wang <zhi.a.wang@intel.com>
Cc: <intel-gfx@lists.freedesktop.org>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
- GP102/GP104 devinit (suspend/resume, optimus) hang fix
- GP102/GP104 hardware cursor fix
- Fix for a regression on some non-MST monitors that was caused by the
MST work
- Workaround for certain laptops where ACPI sends display hotkey presses
on a modeset, causing gnome-settings-daemon to go into a continuous loop
* 'linux-4.10' of git://github.com/skeggsb/linux:
drm/nouveau/disp/gp102: rename from gp104
drm/nouveau/ce/gp102: rename from gp104
drm/nouveau/fb/gp102: rename from gp104
drm/nouveau/disp/gp102: fix cursor/overlay immediate channel indices
drm/nouveau/disp/nv50-: specify ctrl/user separately when constructing classes
drm/nouveau/disp/nv50-: split chid into chid.ctrl and chid.user
drm/nouveau: Intercept ACPI_VIDEO_NOTIFY_PROBE
drm/nouveau/devinit/gm200: drop pmu reset sequence
drm/nouveau/devinit/gm200: replace while loops with PTIMER-based timeout loops
drm/nouveau/pmu/gp102: initial implementation
drm/nouveau/pmu/gp100: initial implementation
drm/nouveau/pmu: execute reset before running devinit
drm/nouveau/pmu: move ucode handling into gt215 implementation
drm/nouveau/core: initial support for GP102
drm/nouveau/device/pci: fix oops if no mmu subdev present
drm/nouveau/kms/nv50: avoid touching DP_MSTM_CTRL if !DP_MST_CAP
Replace direct comparisons to NULL i.e.
'x == NULL' with '!x'. As per coding standard.
Signed-off-by: Ravikant B Sharma <ravikant.s2@samsung.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
'dma_buf_map_attachment()' can not return NULL, so there is no need to
check for it.
Also add a space in order to improve layout.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
We get 2 warnings when building kernel with W=1:
drivers/gpu/drm/armada/armada_gem.c:215:27: warning: no previous prototype for 'armada_gem_alloc_object' [-Wmissing-prototypes]
drivers/gpu/drm/armada/armada_gem.c:423:1: warning: no previous prototype for 'armada_gem_prime_map_dma_buf' [-Wmissing-prototypes]
In fact, both functions are only used in the file in which they are
declared and don't need a declaration, but can be made static.
So this patch marks these functions with 'static'.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Now that the drm_connector_register() is gone from tda998x, we can
remove the mid-layer from armada-drm, eliminating the load, unload,
debugfs_init, and debugfs_cleanup callbacks from armada's drm_driver
structure. No functional changes.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Various notebooks with nvidia GPUs generate an ACPI_VIDEO_NOTIFY_PROBE
acpi-video event when an external device gets plugged in (and again on
modesets on that connector), the default behavior in the acpi-video
driver for this is to send a KEY_SWITCHVIDEOMODE evdev event, which
causes e.g. gnome-settings-daemon to ask us to rescan the connectors
(good), but also causes g-s-d to switch to mirror mode on a newly plugged
monitor rather then using the monitor to extend the desktop (bad)
as KEY_SWITCHVIDEOMODE is supposed to switch between extend the desktop
vs mirror mode.
More troublesome are the repeated ACPI_VIDEO_NOTIFY_PROBE events on
changing the mode on the connector, which cause g-s-d to switch
between mirror/extend mode, which causes a new ACPI_VIDEO_NOTIFY_PROBE
event and we end up with an endless loop.
This commit fixes this by adding an acpi notifier block handler to
nouveau_display.c to intercept ACPI_VIDEO_NOTIFY_PROBE and:
1) Wake-up runtime suspended GPUs and call drm_helper_hpd_irq_event()
on them, this is necessary in some cases for the GPU to detect connector
hotplug events while runtime suspended
2) Return NOTIFY_BAD to stop acpi-video from emitting a bogus
KEY_SWITCHVIDEOMODE key-press event
There already is another acpi notifier block handler registered in
drivers/gpu/drm/nouveau/nvkm/engine/device/acpi.c, but that is not
suitable since that one gets unregistered on runtime suspend, and
we also want to intercept ACPI_VIDEO_NOTIFY_PROBE when runtime suspended.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This sequence is incorrect for GP102/GP104 boards. This is now being
handled correctly by the PMU subdev during preinit();
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
