Most of DT files in ARM use #include "..." to make pre-processor
include DT in the same directory, but we have some exceptional files
that use #include <...> for that.
Fix them to remove -I$(srctree)/arch/$(SRCARCH)/boot/dts path from
dtc_cpp_flags.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
"bcrmf" is a typo and "wifi" is the preferred form to describe
such node, so change it accordingly.
Reported-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Currently the following eMMC error is seen:
mmc1: mmc_select_hs200 failed, error -74
mmc1: new MMC card at address 0001
mmcblk1: mmc1:0001 V10008 7.05 GiB
mmcblk1boot0: mmc1:0001 V10008 partition 1 4.00 MiB
mmcblk1boot1: mmc1:0001 V10008 partition 2 4.00 MiB
mmcblk1rpmb: mmc1:0001 V10008 partition 3 4.00 MiB
On imx7s-warp the eMMC VCCQ is fixed at 3.15V, so pass the 'no-1-8-v'
property to properly describe that 1.8V operation is not possible.
With this change HS200 error is gone and another benefit is that the
card can operate in DDR52 mode now:
mmc1: new DDR MMC card at address 0001
mmcblk1: mmc1:0001 V10008 7.05 GiB
mmcblk1boot0: mmc1:0001 V10008 partition 1 4.00 MiB
mmcblk1boot1: mmc1:0001 V10008 partition 2 4.00 MiB
mmcblk1rpmb: mmc1:0001 V10008 partition 3 4.00 MiB
Suggested-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the initial support for imx7d-pico board.
Add support for eMMC, USB host, USB device, PMIC, Ethernet and audio.
For more information about this board, please visit:
http://www.technexion.org/products/pico/pico-som/pico-imx7-emmc
Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The PWM driver has now capability to specify the PWM polarity
which is e.g. for backlight control. Allow to make use of PWM
polarity by specifying pwm-cells to be 3 in the base dt.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
List GPR block as compatible "fsl,imx6q-iomuxc-gpr" to support drivers
requesting it that way (PCIe driver is one example).
Cc: yurovsky@gmail.com
Cc: Dong Aisheng <aisheng.dong@nxp.com>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Now that support for 'anatop-enable-bit' has been added to ANADIG
driver, reintroduce 'anatop-enable-bit' for all applicable LDOs.
Cc: yurovsky@gmail.com
Cc: Dong Aisheng <aisheng.dong@nxp.com>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On imx6sx-sdb rev B/C the VDD_ARM_IN and VDD_SOC_IN supplies are connected
together and both are supplied by the SW1A PMIC output, so model this
correctly in the device tree.
Suggested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
When running a stress playback/stop loop test on a mx6colibri channel
swaps can be noticed randomly.
Increasing the SGTL5000 LRCLK pad strength to its maximum value fixes
the issue, so add the 'lrclk-strength' property to avoid the audio
channel swaps.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
When running a stress playback/stop loop test on a mx6wandboard channel
swaps can be noticed randomly.
Increasing the SGTL5000 LRCLK pad strength to its maximum value fixes
the issue, so add the 'lrclk-strength' property to avoid the audio
channel swaps.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The USDHC instances need the USDHC NAND and IPG clock in order to
operate. Reference them properly by replacing the dummy clocks with
the actual clocks.
Note that both clocks are currently implicitly enabled since they
are part of the i.MX 7 clock drivers init_on list. This might
change in the future.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The rv4162 compatbile string is missing the vendor part, add it.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The rv4162 vendor is microcrystal, not ST.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The rv4162 vendor is microcrystal, not ST.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the more specific QuadPlus compatible to the GPC node, to trigger the
required workarounds in the power domain code.
In regard to the interrupt mapping the QuadPlus controller is fully
compatible to the Quad one, so keep that compatible in place.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Adopt the i.MX6Q/DL DT to the new and more flexible GPC binding.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Remove the sky2 ethernet device node from the pcie controller which was
invalid to begin with.
The original intent was to allow the bootloader to populate the MAC via
dt but this requires the PCI bus topology to be complete in dt as well
and as these boards have an expansion connector that topology is dynamic
and can't be represented here.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
to me not catching up as quickly on patch review than anything else.
Overall it seems normal though, a few small changes to the core, mostly
small non-critical fixes here and there as well as driver updates for new
and existing hardware support. The biggest things are the TI clk driver
rework to lay the groundwork for clkctrl support in the next merge window
and the AmLogic audio/graphics clk support.
Core:
* clk_possible_parents debugfs file so we know which parents a clk
could possibly have
* Fix to make clk rate change notifiers stop on the first failure instead
of continuing
New Drivers:
* Mediatek MT6797 SoCs
* hi655x PMIC clks
* AmLogic Meson SoC i2s and spdif audio clks and Mali graphics clks
* Allwinner H5 SoCs and PRCM hardware
Updates:
* Nvidia Tegra T210 cleanups and non-critical fixes
* TI OMAP cleanups in preparation for clkctrl support
* Trivial fixes like kcalloc(), devm_* conversions, and seq_puts()
* ZTE zx296718 SoC VGA clks
* Rockchip clk-ids, fixups, and rename of rk1108 to rv1108
* Support for IDT VersaClock 5P49V5935
* Renesas R-Car H3 and M3-W IMR clks and ES2.0 rev of R-Car H3 support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=/5a/
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"Sort of on the quieter side this time, which is probably due more to
me not catching up as quickly on patch review than anything else.
Overall it seems normal though, a few small changes to the core,
mostly small non-critical fixes here and there as well as driver
updates for new and existing hardware support.
The biggest things are the TI clk driver rework to lay the groundwork
for clkctrl support in the next merge window and the AmLogic
audio/graphics clk support.
Core:
- clk_possible_parents debugfs file so we know which parents a clk
could possibly have
- Fix to make clk rate change notifiers stop on the first failure
instead of continuing
New Drivers:
- Mediatek MT6797 SoCs
- hi655x PMIC clks
- AmLogic Meson SoC i2s and spdif audio clks and Mali graphics clks
- Allwinner H5 SoCs and PRCM hardware
Updates:
- Nvidia Tegra T210 cleanups and non-critical fixes
- TI OMAP cleanups in preparation for clkctrl support
- trivial fixes like kcalloc(), devm_* conversions, and seq_puts()
- ZTE zx296718 SoC VGA clks
- Rockchip clk-ids, fixups, and rename of rk1108 to rv1108
- IDT VersaClock 5P49V5935 support
- Renesas R-Car H3 and M3-W IMR clks and ES2.0 rev of R-Car H3
support"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (151 commits)
clk: x86: pmc-atom: Checking for IS_ERR() instead of NULL
clk: ti: divider: try to fix ti_clk_register_divider
clk: mvebu: Use kcalloc() in two functions
clk: mvebu: Use kcalloc() in of_cpu_clk_setup()
clk: nomadik: Delete error messages for a failed memory allocation in two functions
clk: nomadik: Use seq_puts() in nomadik_src_clk_show()
clk: Improve a size determination in two functions
clk: Replace four seq_printf() calls by seq_putc()
clk: si5351: Delete an error message for a failed memory allocation in si5351_i2c_probe()
clk: si5351: Use devm_kcalloc() in si5351_i2c_probe()
clk: at91: Use kcalloc() in of_at91_clk_pll_get_characteristics()
reset: mediatek: Add MT2701 ethsys reset controller include file
clk: mediatek: add mt2701 ethernet reset
clk: hi6220: Add the hi655x's pmic clock
clk: ti: fix building without legacy omap3
clk: ti: fix linker error with !SOC_OMAP4
clk: hi3620: Fix a typo in one variable name
clk: hi3620: Delete error messages for a failed memory allocation in two functions
clk: hi3620: Use kcalloc() in hi3620_mmc_clk_init()
clk: hisilicon: Delete error messages for failed memory allocations in hisi_clk_init()
...
Device-tree updates for arm64 platforms. Just as with 32-bit, a bunch of smaller
changes, but also some new platforms that are worth mentioning:
* Rockchip RK3399 platforms for Chromebooks, including Samsung Chromebook
Plus (Kevin)
* Orange Pi PC2 (Allwinner H5)
* Freescale LS2088A and LS1088A SoCs
* Expanded support for Nvidia Tegra186 (and Jetson TX2)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=q3Ix
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM 64-bit DT updates from Olof Johansson:
"Device-tree updates for arm64 platforms. Just as with 32-bit, a bunch
of smaller changes, but also some new platforms that are worth
mentioning:
- Rockchip RK3399 platforms for Chromebooks, including Samsung
Chromebook Plus (Kevin)
- Orange Pi PC2 (Allwinner H5)
- Freescale LS2088A and LS1088A SoCs
- Expanded support for Nvidia Tegra186 (and Jetson TX2)"
* tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (180 commits)
arm64: dts: Add basic DT to support Spreadtrum's SP9860G
arm64: dts: exynos: Use - instead of @ for DT OPP entries
arm64: dts: exynos: Add support for s6e3hf2 panel device on TM2e board
arm64: dts: juno: add information about L1 and L2 caches
arm64: dts: juno: fix few unit address format warnings
arm64: marvell: dts: enable the crypto engine on the Armada 8040 DB
arm64: marvell: dts: enable the crypto engine on the Armada 7040 DB
arm64: marvell: dts: add crypto engine description for 7k/8k
arm64: dts: marvell: add sdhci support for Armada 7K/8K
arm64: dts: marvell: add eMMC support for Armada 37xx
arm64: dts: hisi: add pinctrl dtsi file for HiKey960 development board
arm64: dts: hisi: add drive strength levels of the pins for Hi3660 SoC
arm64: dts: hisi: enable the NIC and SAS for the hip07-d05 board
arm64: dts: hisi: add SAS nodes for the hip07 SoC
arm64: dts: hisi: add RoCE nodes for the hip07 SoC
arm64: dts: hisi: add network related nodes for the hip07 SoC
arm64: dts: hisi: add mbigen nodes for the hip07 SoC
arm64: dts: rockchip: fix the memory size of PX5 Evaluation board
arm64: dts: hisilicon: add dts files for hi3798cv200-poplar board
dt-bindings: arm: hisilicon: add bindings for hi3798cv200 SoC and Poplar board
...
Device-tree continues to see lots of updates. The majority of patches
here are smaller changes for new hardware on existing platforms, and
there are a few larger changes worth pointing out.
Major new platforms:
- Gemini has been ported to DT, so a handful of "new" platforms moved over
from board files
- Rockchip RK3288 support for Tinkerboard and Phytec phyCORE-RK3288 SoM and RDK
- A bunch of embedded platforms, several Linksys platforms, Synology DS116,
- Motorola Droid4 (really old OMAP-based phone) support is added.
Some refactorings, i.e. Allwinner H3/H5 support is commonalized.
And lots of smaller changes, cleanups, etc. See shortlog for more description
We're adding ability to cross-include DT files between arm and arm64,
by creating appropriate links in the dt-include directory, and using arm/
and arm64/ as include prefixes. This will avoid other local hacks such as
per-file links between the two arch trees (this broke for external mirroring
of DT contents). Now they can just provide their own appropriate dt-include
hierarcy per platform.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=v6w6
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM Device-tree updates from Olof Johansson:
"Device-tree continues to see lots of updates. The majority of patches
here are smaller changes for new hardware on existing platforms, and
there are a few larger changes worth pointing out.
Major new platforms:
- Gemini has been ported to DT, so a handful of "new" platforms moved
over from board files
- Rockchip RK3288 support for Tinkerboard and Phytec phyCORE-RK3288
SoM and RDK
- A bunch of embedded platforms, several Linksys platforms, Synology
DS116,
- Motorola Droid4 (really old OMAP-based phone) support is added.
Some refactorings, i.e. Allwinner H3/H5 support is commonalized.
And lots of smaller changes, cleanups, etc. See shortlog for more
description
We're adding ability to cross-include DT files between arm and arm64,
by creating appropriate links in the dt-include directory, and using
arm/ and arm64/ as include prefixes. This will avoid other local hacks
such as per-file links between the two arch trees (this broke for
external mirroring of DT contents). Now they can just provide their
own appropriate dt-include hierarcy per platform"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (349 commits)
ARM: dts: exynos: Use - instead of @ for DT OPP entries
arm: spear6xx: add DT description of the ADC on SPEAr600
arm: spear6xx: remove unneeded pinctrl properties in spear600-evb
arm: spear6xx: switch spear600-evb to the new flash partition DT binding
arm: spear6xx: fix spaces in spear600-evb.dts
arm: spear6xx: use node labels in spear600-evb.dts
arm: spear6xx: add labels to various nodes in spear600.dtsi
ARM: dts: vexpress: fix few unit address format warnings
ARM: dts: at91: sama5d3_xplained: not all ADC channels are available
ARM: dts: at91: sama5d3_xplained: fix ADC vref
ARM: dts: at91: add envelope detector mux to the Axentia TSE-850
ARM: dts: armada-38x: label USB and SATA nodes
ARM: dts: imx6q-utilite-pro: add hpd gpio
ARM: dts: imx6qp-sabresd: Set reg_arm regulator supply
ARM: dts: imx6qdl-sabresd: Set LDO regulator supply
ARM: dts: imx: add Gateworks Ventana GW5903 support
ARM: dts: i.MX25: add AIPS control registers
ARM: dts: imx7-colibri: add Carrier Board 3.3V/5V regulators
ARM: dts: imx7-colibri: remove 1.8V fixed regulator
ARM: dts: imx7-colibri: allow to disable Ethernet rail
...
Pull ARM updates from Russell King:
"Lots of little things this time:
- allow modules to be autoloaded according to the HWCAP feature bits
(used primarily for crypto modules)
- split module core and init PLT sections, since the core code and
init code could be placed far apart, and the PLT sections need to
be local to the code block.
- three patches from Chris Brandt to allow Cortex-A9 L2 cache
optimisations to be disabled where a SoC didn't wire up the out of
band signals.
- NoMMU compliance fixes, avoiding corruption of vector table which
is not being used at this point, and avoiding possible register
state corruption when switching mode.
- fixmap memory attribute compliance update.
- remove unnecessary locking from update_sections_early()
- ftrace fix for DEBUG_RODATA with !FRAME_POINTER"
* 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 8672/1: mm: remove tasklist locking from update_sections_early()
ARM: 8671/1: V7M: Preserve registers across switch from Thread to Handler mode
ARM: 8670/1: V7M: Do not corrupt vector table around v7m_invalidate_l1 call
ARM: 8668/1: ftrace: Fix dynamic ftrace with DEBUG_RODATA and !FRAME_POINTER
ARM: 8667/3: Fix memory attribute inconsistencies when using fixmap
ARM: 8663/1: wire up HWCAP/HWCAP2 feature bits to the CPU modalias
ARM: 8666/1: mm: dump: Add domain to output
ARM: 8662/1: module: split core and init PLT sections
ARM: 8661/1: dts: r7s72100: add l2 cache
ARM: 8660/1: shmobile: r7s72100: Enable L2 cache
ARM: 8659/1: l2c: allow CA9 optimizations to be disabled
-----BEGIN PGP SIGNATURE-----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=Snzj
-----END PGP SIGNATURE-----
Merge tag 'media/v4.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
"Media updates for v4.12-rc1:
- new driver to support mediatek jpeg in hardware codec
- rc-lirc, s5p-cec and st-cec staging drivers got promoted
- hardware histogram support for vsp1 driver
- added Virtual Media Controller driver, to make easier to test the
media controller
- added a new CEC driver (rainshadow-cec)
- removed two staging LIRC drivers for obscure hardware that are too
obsolete
- added support for Intel SR300 Depth camera
- some improvements at CEC and RC core
- lots of driver cleanups, improvements all over the tree
With this series, we're finally getting rid of the LIRC staging
driver. There's just one left (lirc_zilog), with require more care,
as part of its functionality (IR RX) is already provided by another
driver. Work in progress to convert it on the proper way"
* tag 'media/v4.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (304 commits)
[media] ov2640: print error if devm_*_optional*() fails
[media] atmel-isc: Fix the static checker warning
[media] ov2640: add support for MEDIA_BUS_FMT_YVYU8_2X8 and MEDIA_BUS_FMT_VYUY8_2X8
[media] ov2640: fix vflip control
[media] ov2640: fix duplicate width+height returning from ov2640_select_win()
[media] ov2640: add missing write to size change preamble
[media] ov2640: add information about DSP register 0xc7
[media] ov2640: improve banding filter register definitions/documentation
[media] ov2640: fix init sequence alignment
[media] ov2640: make GPIOLIB an optional dependency
[media] xc5000: fix spelling mistake: "calibration"
[media] vidioc-queryctrl.rst: fix menu/int menu references
[media] media-entity: only call dev_dbg_obj if mdev is not NULL
[media] pixfmt-meta-vsp1-hgo.rst: remove spurious '-'
[media] mtk-vcodec: avoid warnings because of empty macros
[media] coda: bump maximum number of internal framebuffers to 17
[media] media: mtk-vcodec: remove informative log
[media] subdev-formats.rst: remove spurious '-'
[media] dw2102: limit messages to buffer size
[media] ttusb2: limit messages to buffer size
...
Core changes:
- Add bi-directional and output-enable pin configurations to
the generic bindings and generic pin controlling core.
New drivers or subdrivers:
- Armada 37xx SoC pin controller and GPIO support.
- Axis ARTPEC-6 SoC pin controller support.
- AllWinner A64 R_PIO controller support, and opening up the
AllWinner sunxi driver for ARM64 use.
- Rockchip RK3328 support.
- Renesas R-Car H3 ES2.0 support.
- STM32F469 support in the STM32 driver.
- Aspeed G4 and G5 pin controller support.
Improvements:
- A whole slew of realtime improvements to drivers implementing
irqchips: BCM, AMD, SiRF, sunxi, rockchip.
- Switch meson driver to get the GPIO ranges from the device
tree.
- Input schmitt trigger support on the Rockchip driver.
- Enable the sunxi (AllWinner) driver to also be used on ARM64
silicon.
- Name the Qualcomm QDF2xxx GPIO lines.
- Support GMMR GPIO regions on the Intel Cherryview. This
fixes a serialization problem on these platforms.
- Pad retention support for the Samsung Exynos 5433.
- Handle suspend-to-ram in the AT91-pio4 driver.
- Pin configuration support in the Aspeed driver.
Cleanups:
- The final name of Rockchip RK1108 was RV1108 so rename the
driver and variables to stay consistent.
-----BEGIN PGP SIGNATURE-----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=BCaA
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v4.12 cycle.
The extra week before the merge window actually resulted in some of
the type of fixes that usually arrive after the merge window already
starting to trickle in from eager developers using -next, I'm
impressed.
I have recruited a Samsung subsubsystem maintainer (Krzysztof) to deal
with the onset of Samsung patches. It works great.
Apart from that it is a boring round, just incremental updates and
fixes all over the place, no serious core changes or anything exciting
like that. The most pleasing to see is Julia Cartwrights work to audit
the irqchip-providing drivers for realtime locking compliance. It's
one of those "I should really get around to looking into that" things
that have been on my TODO list since forever.
Summary:
Core changes:
- add bi-directional and output-enable pin configurations to the
generic bindings and generic pin controlling core.
New drivers or subdrivers:
- Armada 37xx SoC pin controller and GPIO support.
- Axis ARTPEC-6 SoC pin controller support.
- AllWinner A64 R_PIO controller support, and opening up the
AllWinner sunxi driver for ARM64 use.
- Rockchip RK3328 support.
- Renesas R-Car H3 ES2.0 support.
- STM32F469 support in the STM32 driver.
- Aspeed G4 and G5 pin controller support.
Improvements:
- a whole slew of realtime improvements to drivers implementing
irqchips: BCM, AMD, SiRF, sunxi, rockchip.
- switch meson driver to get the GPIO ranges from the device tree.
- input schmitt trigger support on the Rockchip driver.
- enable the sunxi (AllWinner) driver to also be used on ARM64
silicon.
- name the Qualcomm QDF2xxx GPIO lines.
- support GMMR GPIO regions on the Intel Cherryview. This fixes a
serialization problem on these platforms.
- pad retention support for the Samsung Exynos 5433.
- handle suspend-to-ram in the AT91-pio4 driver.
- pin configuration support in the Aspeed driver.
Cleanups:
- the final name of Rockchip RK1108 was RV1108 so rename the driver
and variables to stay consistent"
* tag 'pinctrl-v4.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (80 commits)
pinctrl: mediatek: Add missing pinctrl bindings for mt7623
pinctrl: artpec6: Fix return value check in artpec6_pmx_probe()
pinctrl: artpec6: Remove .owner field for driver
pinctrl: tegra: xusb: Silence sparse warnings
ARM: at91/at91-pinctrl documentation: fix spelling mistake: "contoller" -> "controller"
pinctrl: make artpec6 explicitly non-modular
pinctrl: aspeed: g5: Add pinconf support
pinctrl: aspeed: g4: Add pinconf support
pinctrl: aspeed: Add core pinconf support
pinctrl: aspeed: Document pinconf in devicetree bindings
pinctrl: Add st,stm32f469-pinctrl compatible to stm32-pinctrl
pinctrl: stm32: Add STM32F469 MCU support
Documentation: dt: Remove ngpios from stm32-pinctrl binding
pinctrl: stm32: replace device_initcall() with arch_initcall()
pinctrl: stm32: add possibility to use gpio-ranges to declare bank range
pinctrl: armada-37xx: Add gpio support
pinctrl: armada-37xx: Add pin controller support for Armada 37xx
pinctrl: dt-bindings: Add documentation for Armada 37xx pin controllers
pinctrl: core: Make pinctrl_init_controller() static
pinctrl: generic: Add bi-directional and output-enable
...
Pull networking updates from David Millar:
"Here are some highlights from the 2065 networking commits that
happened this development cycle:
1) XDP support for IXGBE (John Fastabend) and thunderx (Sunil Kowuri)
2) Add a generic XDP driver, so that anyone can test XDP even if they
lack a networking device whose driver has explicit XDP support
(me).
3) Sparc64 now has an eBPF JIT too (me)
4) Add a BPF program testing framework via BPF_PROG_TEST_RUN (Alexei
Starovoitov)
5) Make netfitler network namespace teardown less expensive (Florian
Westphal)
6) Add symmetric hashing support to nft_hash (Laura Garcia Liebana)
7) Implement NAPI and GRO in netvsc driver (Stephen Hemminger)
8) Support TC flower offload statistics in mlxsw (Arkadi Sharshevsky)
9) Multiqueue support in stmmac driver (Joao Pinto)
10) Remove TCP timewait recycling, it never really could possibly work
well in the real world and timestamp randomization really zaps any
hint of usability this feature had (Soheil Hassas Yeganeh)
11) Support level3 vs level4 ECMP route hashing in ipv4 (Nikolay
Aleksandrov)
12) Add socket busy poll support to epoll (Sridhar Samudrala)
13) Netlink extended ACK support (Johannes Berg, Pablo Neira Ayuso,
and several others)
14) IPSEC hw offload infrastructure (Steffen Klassert)"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2065 commits)
tipc: refactor function tipc_sk_recv_stream()
tipc: refactor function tipc_sk_recvmsg()
net: thunderx: Optimize page recycling for XDP
net: thunderx: Support for XDP header adjustment
net: thunderx: Add support for XDP_TX
net: thunderx: Add support for XDP_DROP
net: thunderx: Add basic XDP support
net: thunderx: Cleanup receive buffer allocation
net: thunderx: Optimize CQE_TX handling
net: thunderx: Optimize RBDR descriptor handling
net: thunderx: Support for page recycling
ipx: call ipxitf_put() in ioctl error path
net: sched: add helpers to handle extended actions
qed*: Fix issues in the ptp filter config implementation.
qede: Fix concurrency issue in PTP Tx path processing.
stmmac: Add support for SIMATIC IOT2000 platform
net: hns: fix ethtool_get_strings overflow in hns driver
tcp: fix wraparound issue in tcp_lp
bpf, arm64: fix jit branch offset related to ldimm64
bpf, arm64: implement jiting of BPF_XADD
...
Pull crypto updates from Herbert Xu:
"Here is the crypto update for 4.12:
API:
- Add batch registration for acomp/scomp
- Change acomp testing to non-unique compressed result
- Extend algorithm name limit to 128 bytes
- Require setkey before accept(2) in algif_aead
Algorithms:
- Add support for deflate rfc1950 (zlib)
Drivers:
- Add accelerated crct10dif for powerpc
- Add crc32 in stm32
- Add sha384/sha512 in ccp
- Add 3des/gcm(aes) for v5 devices in ccp
- Add Queue Interface (QI) backend support in caam
- Add new Exynos RNG driver
- Add ThunderX ZIP driver
- Add driver for hardware random generator on MT7623 SoC"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (101 commits)
crypto: stm32 - Fix OF module alias information
crypto: algif_aead - Require setkey before accept(2)
crypto: scomp - add support for deflate rfc1950 (zlib)
crypto: scomp - allow registration of multiple scomps
crypto: ccp - Change ISR handler method for a v5 CCP
crypto: ccp - Change ISR handler method for a v3 CCP
crypto: crypto4xx - rename ce_ring_contol to ce_ring_control
crypto: testmgr - Allow ecb(cipher_null) in FIPS mode
Revert "crypto: arm64/sha - Add constant operand modifier to ASM_EXPORT"
crypto: ccp - Disable interrupts early on unload
crypto: ccp - Use only the relevant interrupt bits
hwrng: mtk - Add driver for hardware random generator on MT7623 SoC
dt-bindings: hwrng: Add Mediatek hardware random generator bindings
crypto: crct10dif-vpmsum - Fix missing preempt_disable()
crypto: testmgr - replace compression known answer test
crypto: acomp - allow registration of multiple acomps
hwrng: n2 - Use devm_kcalloc() in n2rng_probe()
crypto: chcr - Fix error handling related to 'chcr_alloc_shash'
padata: get_next is never NULL
crypto: exynos - Add new Exynos RNG driver
...
Pull timer updates from Thomas Gleixner:
"The timer departement delivers:
- more year 2038 rework
- a massive rework of the arm achitected timer
- preparatory patches to allow NTP correction of clock event devices
to avoid early expiry
- the usual pile of fixes and enhancements all over the place"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (91 commits)
timer/sysclt: Restrict timer migration sysctl values to 0 and 1
arm64/arch_timer: Mark errata handlers as __maybe_unused
Clocksource/mips-gic: Remove redundant non devicetree init
MIPS/Malta: Probe gic-timer via devicetree
clocksource: Use GENMASK_ULL in definition of CLOCKSOURCE_MASK
acpi/arm64: Add SBSA Generic Watchdog support in GTDT driver
clocksource: arm_arch_timer: add GTDT support for memory-mapped timer
acpi/arm64: Add memory-mapped timer support in GTDT driver
clocksource: arm_arch_timer: simplify ACPI support code.
acpi/arm64: Add GTDT table parse driver
clocksource: arm_arch_timer: split MMIO timer probing.
clocksource: arm_arch_timer: add structs to describe MMIO timer
clocksource: arm_arch_timer: move arch_timer_needs_of_probing into DT init call
clocksource: arm_arch_timer: refactor arch_timer_needs_probing
clocksource: arm_arch_timer: split dt-only rate handling
x86/uv/time: Set ->min_delta_ticks and ->max_delta_ticks
unicore32/time: Set ->min_delta_ticks and ->max_delta_ticks
um/time: Set ->min_delta_ticks and ->max_delta_ticks
tile/time: Set ->min_delta_ticks and ->max_delta_ticks
score/time: Set ->min_delta_ticks and ->max_delta_ticks
...
-----BEGIN PGP SIGNATURE-----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=NymV
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-4.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt
Pull "Fix DTC warnings in Exynos ARMv7 Device Tree sources." from Krzysztof Kozłowski:
* tag 'samsung-dt-4.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: Use - instead of @ for DT OPP entries
A single fix to remove device tree warnings introduced with recently
added checks in DTC
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=kv8P
-----END PGP SIGNATURE-----
Merge tag 'vexpress-dt-4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into next/dt
Pull "ARMv7 VExpress DT fix for v4.12" from Sudeep Holla:
A single fix to remove device tree warnings introduced with recently
added checks in DTC
* tag 'vexpress-dt-4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
ARM: dts: vexpress: fix few unit address format warnings
Compiling the DT file with W=1, DTC warns like follows:
Warning (unit_address_vs_reg): Node /opp_table0/opp@1000000000 has a
unit name, but no reg property
Fix this by replacing '@' with '-' as the OPP nodes will never have a
"reg" property.
Reported-by: Krzysztof Kozlowski <krzk@kernel.org>
Reported-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Suggested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
[k.kozlowski: Split patch per ARM and ARM64]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
A function in kernel/bpf/syscall.c which got a bug fix in 'net'
was moved to kernel/bpf/verifier.c in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
The SPEAr600 has a built-in ADC, which already has a Device Tree binding
described in
Documentation/devicetree/bindings/staging/iio/adc/spear-adc.txt. This
commit adds the description in the SPEAr600 Device Tree of this ADC
device.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
The spear6xx doesn't have a pinctrl driver, since the pinmux is globally
defined through a single register, generally configured by the
firmware/bootloader.
Therefore, the pinctrl related properties in spear600-evb.dts are not
necessary.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
This commit moves spear600-evb.dts to use the new flash partition Device
Tree binding documented in
Documentation/devicetree/bindings/mtd/partition.txt.
As this Device Tree binding document says: "For backwards compatibility
partitions as direct subnodes of the mtd device are supported. This use
is discouraged."
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
This commit fixes a minor coding style issue in spear600-evb.dts:
missing spaces around equal sign.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Now that we have introduced node labels in spear600.dtsi, we can use
them for spear600-evb.dts.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Having labels allows to more easily reference nodes in .dts files
including spear600.dtsi.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
A bunch of clean up for Alpine device trees, nothing fancy.
-----BEGIN PGP SIGNATURE-----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=aD3G
-----END PGP SIGNATURE-----
Merge tag 'alpine-dt-for-4.12' of https://git.kernel.org/pub/scm/linux/kernel/git/atenart/linux into next/dt
Alpine DT changes for 4.12
A bunch of clean up for Alpine device trees, nothing fancy.
* tag 'alpine-dt-for-4.12' of https://git.kernel.org/pub/scm/linux/kernel/git/atenart/linux:
ARM: dts: alpine: add valid clock-frequency values
ARM: dts: alpine: add spaces before the uart node units.
ARM: dts: alpine: remove 0x's from the uart1 node unit address
ARM: dts: alpine: fix PCIe node name
Signed-off-by: Olof Johansson <olof@lixom.net>
Use label for USB and SATA nodes on Armada 38x
-----BEGIN PGP SIGNATURE-----
iIEEABECAEEWIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCWO+kqSMcZ3JlZ29yeS5j
bGVtZW50QGZyZWUtZWxlY3Ryb25zLmNvbQAKCRALBhiOFHI71V2vAJ47Vu37Pig3
Quq7c68ByWMNhRv0IgCgpJOKmYRrcibw/AbrHIh6ZZUoN7g=
=AtGR
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt-4.12-3' of git://git.infradead.org/linux-mvebu into next/dt
mvebu dt for 4.12 (part 3)
Use label for USB and SATA nodes on Armada 38x
* tag 'mvebu-dt-4.12-3' of git://git.infradead.org/linux-mvebu:
ARM: dts: armada-38x: label USB and SATA nodes
Signed-off-by: Olof Johansson <olof@lixom.net>
Updates to the device tree to include upstreamed drivers:
- SPI flash controller
- Watchdog
- ADC
In addition we describe some of the clocks so that upstream kernels can
boot on hardware.
-----BEGIN PGP SIGNATURE-----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=bGNK
-----END PGP SIGNATURE-----
Merge tag 'aspeed-4.12-devicetree' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/aspeed into next/dt
Aspeed devicetree updates for 4.12
Updates to the device tree to include upstreamed drivers:
- SPI flash controller
- Watchdog
- ADC
In addition we describe some of the clocks so that upstream kernels can
boot on hardware.
* tag 'aspeed-4.12-devicetree' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/aspeed:
arm: dts: aspeed: Describe ADCs for AST2400/AST2500
ARM: dts: aspeed: romulus: Add UART1
ARM: dts: aspeed: Update watchdog compatible strings
ARM: dts: aspeed: Add a fastread property
ARM: dts: aspeed: Add SPI controller bindings to Romulus
ARM: dts: aspeed: Make G4 clocks fixed
ARM: dts: aspeed: Make G5 clocks fixed
ARM: dts: aspeed: add SPI controller bindings
Signed-off-by: Olof Johansson <olof@lixom.net>
to configure various devices:
- Enable DCAN on am57xx-idk
- Enable CPSW ethernet0 and 1 on am335x-icev2
- Non-critical fix for droid 4 PMIC interrupt triggering
- Stop disabling SRAM and GPMC on droid 4
- Configure CPCAP PMIC related devices on droid 4 for ADC, charger
and USB PHY. The charger and USB PHY drivers are still being
discussed, but the binding for them has been acked by Rob and
Sebastian so they should be safe to merge together with the ADC
driver in Linux next that they depend on
-----BEGIN PGP SIGNATURE-----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=Jna8
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.12/dt-pt2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Second set of devicetree changes for omaps for v4.12 merge window
to configure various devices:
- Enable DCAN on am57xx-idk
- Enable CPSW ethernet0 and 1 on am335x-icev2
- Non-critical fix for droid 4 PMIC interrupt triggering
- Stop disabling SRAM and GPMC on droid 4
- Configure CPCAP PMIC related devices on droid 4 for ADC, charger
and USB PHY. The charger and USB PHY drivers are still being
discussed, but the binding for them has been acked by Rob and
Sebastian so they should be safe to merge together with the ADC
driver in Linux next that they depend on
* tag 'omap-for-v4.12/dt-pt2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: omap4-droid4: Add CPCAP PMIC OTG PHY configuration
ARM: dts: omap4-droid4: Add CPCAP PMIC battery charger configuration
ARM: dts: omap4-droid4: Add CPCAP PMIC ADC configuration
ARM: dts: omap4-droid4: Stop disabling SRAM and GPMC
ARM: dts: omap4-droid4: Fix interrupt triggering for cpcap
ARM: dts: am335x-icev2: Add CPSW ethernet0 and ethernet1
ARM: dts: am57xx-idk: Add DCAN support
Signed-off-by: Olof Johansson <olof@lixom.net>
- New board support: I2SE's i.MX28 Duckbill-2 boards, Gateworks Ventana
i.MX6 GW5903/GW5904, Zodiac Inflight Innovations RDU2 board, Engicam
i.CoreM6 Quad/Dual OpenFrame modules, Boundary Device i.MX6 Quad Plus
SOM.
- Improve compatible string for i.MX50 eSDHC, i.MX7S SRC devices and
i.MX6SX UART device.
- Add interrupts for switch and PHY devices on VF610 ZII Devel C board.
- Add LVDS, LCD backlight, touchscreen and SAI2 support for i.MX6
icore, geam, and isiot boards.
- A series from Lucas Stach to improve i.MX6Q Plus device tree and add
PRE/PRG devices.
- A series from Stefan Agner to update imx7-colibri device tree
regarding to display, PMIC/regulator support.
- Fix PCI bus DTC warnings seen with the latest compiler.
- Set default phy_type and dr_mode for i.MX25 USBOTG port.
- A couple of small improvements on i.MX25 pin function DT header.
- Add audio support for imx6q-cm-fx6 board using Wolfson wm8731 codec
which is muxed to SSI2 device.
- Other random updates, small fixes and trivial cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJY65XcAAoJEFBXWFqHsHzO0goH/jVVtrnkbfzjEZ+jSU30XY+L
8kR/R+5+PgT3LXZ/U3ZHWqbLOrYtnsmqUjA4loaRwTfyMEPnkRx86XUE86U/xfVy
FuWhFuQ/lLDyfon/CvrEXQ73+CTq8Q5PBqKefg9twi5fNkN2wRqVCD5i4cVgxMpi
KF6DchLv0eW2Zn6fYySf4zNcOIvbkma/qn/Ju2kZEP6TKadIgYvX5Tcw47d2fKsv
E5vypBXdWlNV4SzZyAm4CS9X3pjIQa8zIXHyJAeiqBY/2H7u6z/UvOqnRt0RFnX5
eaVtHF2DwuC9DyjyNVBK1Fhi/7++nnmbLRvBK9G4LBZNmIbcWJEVMHsQcsDQ2h8=
=hpdP
-----END PGP SIGNATURE-----
Merge tag 'imx-dt-4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt
i.MX device tree updates for 4.12:
- New board support: I2SE's i.MX28 Duckbill-2 boards, Gateworks Ventana
i.MX6 GW5903/GW5904, Zodiac Inflight Innovations RDU2 board, Engicam
i.CoreM6 Quad/Dual OpenFrame modules, Boundary Device i.MX6 Quad Plus
SOM.
- Improve compatible string for i.MX50 eSDHC, i.MX7S SRC devices and
i.MX6SX UART device.
- Add interrupts for switch and PHY devices on VF610 ZII Devel C board.
- Add LVDS, LCD backlight, touchscreen and SAI2 support for i.MX6
icore, geam, and isiot boards.
- A series from Lucas Stach to improve i.MX6Q Plus device tree and add
PRE/PRG devices.
- A series from Stefan Agner to update imx7-colibri device tree
regarding to display, PMIC/regulator support.
- Fix PCI bus DTC warnings seen with the latest compiler.
- Set default phy_type and dr_mode for i.MX25 USBOTG port.
- A couple of small improvements on i.MX25 pin function DT header.
- Add audio support for imx6q-cm-fx6 board using Wolfson wm8731 codec
which is muxed to SSI2 device.
- Other random updates, small fixes and trivial cleanups.
* tag 'imx-dt-4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (56 commits)
ARM: dts: imx6q-utilite-pro: add hpd gpio
ARM: dts: imx6qp-sabresd: Set reg_arm regulator supply
ARM: dts: imx6qdl-sabresd: Set LDO regulator supply
ARM: dts: imx: add Gateworks Ventana GW5903 support
ARM: dts: i.MX25: add AIPS control registers
ARM: dts: imx7-colibri: add Carrier Board 3.3V/5V regulators
ARM: dts: imx7-colibri: remove 1.8V fixed regulator
ARM: dts: imx7-colibri: allow to disable Ethernet rail
ARM: dts: imx7-colibri: fix PMIC voltages
ARM: dts: imx7-colibri: use OF graph to describe the display
ARM: dts: imx6qp-nitrogen6_som2: add Quad Plus variant of the SOM
ARM: dts: imx6q-icore: Add touchscreen node
ARM: dts: vf610-zii-dev-rev-b: change switch2 label
ARM: dts: imx6ul-[geam|isiot]: Add sai2 node
ARM: dts: imx6ul-isiot-common: Add touchscreen node
ARM: dts: imx6ul-isiot: Add i2c nodes
ARM: dts: imx6ul-isiot: Add imx6ul-isiot-common.dtsi
ARM: dts: imx6ul-isiot: Add backlight support for lcdif
ARM: dts: imx6ul-geam: Add backlight support for lcdif
ARM: dts: imx6: add ZII RDU2 boards
...
Signed-off-by: Olof Johansson <olof@lixom.net>
board, the phyCORE som and its PCM-947 carrier board from Phytec.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAljpQsEQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgSw5CACTf+7cvykZ3aKvtfo76yacC84mSMdLFOQl
IPkQBX6cV2CEes8xoKjsHXwvYgpgX6Jz58S86ATfi+h3uMu4l7dld+yMaipTcZp/
ROCtf16r+sjq3kndDGoqSFyq5+YZ2En+mz+86YDdEYS3vZvASp+gSVRkn7NUPlrU
+O2Wb8mdY+Hl8XYSZcsmQ7zNjxw/G9pyqVly0/3aSuHRVAbtn4KyunbfkhHdK4LJ
NOFji0t+FIXEr8FNBpiRFnIQ19KILzWmrIr5c92Tz+t11R8+wSIwITYpsAomwVqO
QWtI1alwusJHY2MwdLXlFtBAW3BwsTt72gasl6AigpvYIP0AxKna
=R6eU
-----END PGP SIGNATURE-----
Merge tag 'v4.12-rockchip-dts32-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
Support for the usb-sata controller on the rock2 and another new rk3288
board, the phyCORE som and its PCM-947 carrier board from Phytec.
* tag 'v4.12-rockchip-dts32-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: Add support for PCM-947 carrier board
dt-bindings: Document Phytec phyCORE-RK3288 RDK
ARM: dts: rockchip: Add support for phyCORE-RK3288 SoM
ARM: dts: rockchip: Enable sata support on rock2 square
Signed-off-by: Olof Johansson <olof@lixom.net>
1. Enhancements to PCIe nodes on Exynos5440.
2. Fix thermal values on some of Exynos5420 boards like Odroid XU3.
3. Add proper clock frequency properties to DSI nodes.
4. Fix watchdog reset on Exynos4412.
5. Fix watchdog infinite interrupt in soft mode on Exynos4210,
Exynos5440, S3C64xx and S5Pv210.
6. Enable watchdog on Exynos4 and S3C SoCs.
-----BEGIN PGP SIGNATURE-----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=QHlh
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt
Samsung DeviceTree ARM update for v4.12:
1. Enhancements to PCIe nodes on Exynos5440.
2. Fix thermal values on some of Exynos5420 boards like Odroid XU3.
3. Add proper clock frequency properties to DSI nodes.
4. Fix watchdog reset on Exynos4412.
5. Fix watchdog infinite interrupt in soft mode on Exynos4210,
Exynos5440, S3C64xx and S5Pv210.
6. Enable watchdog on Exynos4 and S3C SoCs.
* tag 'samsung-dt-4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: add HDMI controller phandle to exynos4.dtsi
ARM: dts: s5pv210: Fix infinite interrupt in soft mode
ARM: dts: s3c64xx: Fix infinite interrupt in soft mode
ARM: dts: exynos: Fix infinite interrupt in soft mode on Exynos4210 and Exynos5440
ARM: dts: exynos: Enable watchdog on all Exynos4 boards
ARM: dts: s3c64xx: Enable watchdog on all S3C64xx boards
ARM: dts: exynos: Fix watchdog reset on Exynos4412
ARM: dts: exynos: Add the burst and esc clock frequency properties to DSI node
ARM: dts: exynos: Do not ignore real-world fuse values for thermal zone 0 on Exynos5420
ARM: dts: exynos: Add phy-pcie node for pcie to Exynos5440
Signed-off-by: Olof Johansson <olof@lixom.net>
