Rename the low_power_ctrl field to low_power_ctrl_an to be properly
descriptive of it being an autoneg field.
Signed-off-by: Lev Faerman <lev.faerman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Firmware now reports AN28, AN32, and AN73. Add a helper and check these new
values and report PHY autoneg capability.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add debug logs for ice_aq_get_phy_caps(), and format
ice_aq_set_phy_cfg() and ice_aq_get_link_info() debug logs to make them
more readable.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When the Port Disable bit is set in the Link Default Override Mask TLV PFA
module in the NVM, Total Port Shutdown mode is supported and enabled. In
this mode, the driver should act as if the link-down-on-close ethtool
private flag is always enabled and dis-allow any change to that flag.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Adds functions to check for link override firmware support and get
the override settings for a port. The previously supported/default link
mode was strict mode.
In strict mode link is configured based on get PHY capabilities PHY types
with media.
Lenient mode is now the default link mode. In lenient mode the link is
configured based on get PHY capabilities PHY types without media. This
allows the user to configure link that the media does not report. Limit the
minimum supported link mode to 25G for devices that support 100G, and 1G
for devices that support less than 100G.
Default override is only supported in lenient mode. If default override
is supported and enabled, then default override values are used for
configuring speed and FEC. Default override provide persistent link
settings in the NVM.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Signed-off-by: Evan Swanson <evan.swanson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
After the transition from no media to media FW will clear the
set-phy-cfg data set by the user. Save initial PHY settings and any
settings later requested by the user and use that data to restore PHY
settings on media insertion. Since PHY configuration is now being stored,
replace calls that were calling FW to get the configuration with the saved
copy.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Signed-off-by: Chinh T Cao <chinh.t.cao@intel.com>
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The call to ice_cfg_phy_fec() requires the caller to perform certain
actions before calling it. Instead of imposing these preconditions move
the operations into the function and perform them ourselves.
Also, fix some style issues in nearby touched code.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Signed-off-by: Chinh T Cao <chinh.t.cao@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Create a helper function for configuring requested flow control so that it
can be utilized by other functions looking to configure flow control
settings. Utilize the existing helper ice_copy_phy_caps_to_cfg() to copy a
PHY capability to configuration instead duplicating the code for it.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add callbacks needed to support advanced power management for Wake on LAN.
Also make ice_pf_state_is_nominal function available for all configurations
not just CONFIG_PCI_IOV.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Using the new ice_aq_list_caps and ice_parse_(dev|func)_caps functions,
replace ice_discover_caps with two functions that each take a pointer to
the dev_caps and func_caps structures respectively.
This makes the side effect of updating the hw->dev_caps and
hw->func_caps obvious from reading the implementation of the function.
Additionally, it opens the way for enabling reading of device
capabilities outside of the initialization flow. By passing in
a pointer, another caller will be able to read the capabilities without
modifying the HW capabilities structures.
As there are no other callers, it is safe to now remove
ice_aq_discover_caps and ice_parse_caps.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The ice_parse_caps function is used to convert the capability block data
coming from firmware into a structured format used by other parts of the
code.
The current implementation directly updates the hw->func_caps and
hw->dev_caps structures. It is directly called from within
ice_aq_discover_caps. This causes the discover_caps function to have the
side effect of modifying the HW capability structures, which is not
intuitive.
Split this function into ice_parse_dev_caps and ice_parse_func_caps.
These functions will take a pointer to the dev_caps and func_caps
respectively. Also create an ice_parse_common_caps for sharing the
capability logic that is common to device and function.
Doing so enables a future refactor to allow reading and parsing
capabilities into a local caps structure instead of modifying the
members of the HW structure directly.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The ice_discover_caps function is used to read the device and function
capabilities, updating the hardware capabilities structures with
relevant data.
The exact number of capabilities returned by the hardware is unknown
ahead of time. The AdminQ command will report the total number of
capabilities in the return buffer.
The current implementation involves requesting capabilities once,
reading this returned size, and then re-requested with that size.
This isn't really necessary. The firmware interface has a maximum size
of ICE_AQ_MAX_BUF_LEN. Firmware can never return more than
ICE_AQ_MAX_BUF_LEN / sizeof(struct ice_aqc_list_caps_elem) capabilities.
Avoid the retry loop by simply allocating a buffer of size
ICE_AQ_MAX_BUF_LEN. This is significantly simpler than retrying. The
extra allocation isn't a big deal, as it will be released after we
finish parsing the capabilities.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Use eth_zero_addr() to clear mac address insetad of memset().
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check MC_CMD_DRV_ATTACH_EXT_OUT_FLAG_TRUSTED, before setting
the info, which will hopefully protect us from -EPERM errors
the previous code was gracefully ignoring. Ed reports this
is not the 100% correct bit, but it's the best approximation
we have. Shared code reports the port information back to user
space, so we really want to know what was added and what failed.
Ignoring -EPERM is not an option.
The driver does not call udp_tunnel_get_rx_info(), so its own
management of table state is not really all that problematic,
we can leave it be. This allows the driver to continue with its
copious table syncing, and matching the ports to TX frames,
which it will reportedly do one day.
Leave the feature checking in the callbacks, as the device may
remove the capabilities on reset.
Inline the loop from __efx_ef10_udp_tnl_lookup_port() into
efx_ef10_udp_tnl_has_port(), since it's the only caller now.
With new infra this driver gains port replace - when space frees
up in a full table a new port will be selected for offload.
Plus efx will no longer sleep in an atomic context.
v2:
- amend the commit message about TRUSTED not being 100%
- add TUNNEL_ENCAP_UDP_PORT_ENTRY_INVALID to mark unsed
entries
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-By: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add XDP_REDIRECT case handling and the corresponding NDO to support
redirecting XDP frames. This also includes registering driver memory
model (currently order-0 page mode) in BPF subsystem.
The total number of XDP queues is usually 1:1 with Rx ones.
Signed-off-by: Alexander Lobakin <alobakin@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current XDP Tx logic is suboptimal and can't be reused for XDP_REDIRECT
path.
Make qede_xdp_{tx_int,xmit}() more universal and effective in general to
allow future expanding.
Misc: use unlikely() hints where appropriate and replace "fallthrough"
comments with pseudo-keywords.
Signed-off-by: Alexander Lobakin <alobakin@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Correct the indentation of net_device_ops declarations for fancier look.
Signed-off-by: Alexander Lobakin <alobakin@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the file more readable and easier for adding new fields.
Misc: use IFNAMSIZ and netdev_name() instead of sizeof_field()
and direct net_device::name dereferencing.
Signed-off-by: Alexander Lobakin <alobakin@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend current infrastructure to store chain page size in a struct
and use it in all functions instead of fixed QED_CHAIN_PAGE_SIZE.
Its value remains the default one, but can be overridden in
qed_chain_init_params before chain allocation.
Signed-off-by: Alexander Lobakin <alobakin@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To simplify qed_chain_alloc() prototype and call sites, introduce struct
qed_chain_init_params to specify chain params, and pass a pointer to
filled struct to the actual qed_chain_alloc() instead of a long list
of separate arguments.
Signed-off-by: Alexander Lobakin <alobakin@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fill PBL table parameters for chains with an external PBL data earlier on
qed_chain_init_params() rather than on allocation itself. This simplifies
allocation code and allows to extend struct ext_pbl for other chain types.
Signed-off-by: Alexander Lobakin <alobakin@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qed_chain_init*() are used in one file/place on "cold" path only, so they
can be uninlined and moved next to the call sites.
Signed-off-by: Alexander Lobakin <alobakin@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PBL chain elements are actually DMA addresses stored in __le64, but
currently their size is hardcoded to 8, and DMA addresses are assigned
via cast to variable-sized dma_addr_t without any bitwise conversions.
Change the type of pbl_virt array to match the actual one, add a new
field to store the size of allocated DMA memory and sanitize elements
assignment.
Misc: give more logic names to the members of qed_chain::pbl_sp embedded
struct.
Signed-off-by: Alexander Lobakin <alobakin@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Zero-initialize chain on qed_chain_free(), so it couldn't be freed
twice and provoke undefined behaviour.
Signed-off-by: Alexander Lobakin <alobakin@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move chain allocation/freeing functions to a new file to not mix it with
hardware-related code.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Alexander Lobakin <alobakin@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
List one entry per line and sort them alphabetically to simplify the
addition of the new ones.
Signed-off-by: Alexander Lobakin <alobakin@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently when netdev fails to allocate the error return path
fails to free the allocated object 'lid'. Fix this by setting
err to the return error code and jumping to a new label that
performs the kfree of lid before returning.
Addresses-Coverity: ("Resource leak")
Fixes: 4b03b27349 ("ionic: get MTU from lif identity")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
The variable current_head_index is being initialized with a value that
is never read and it is being updated later with a new value. Replace
the initialization of -1 with the latter assignment.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
enetc_imdio_remove() is missing from the enetc_pf_probe()
bailout path. Not surprisingly because enetc_setup_serdes()
is registering the imdio bus for internal purposes, and it's
not obvious that enetc_imdio_remove() currently performs the
teardown of enetc_setup_serdes().
To fix this, define enetc_teardown_serdes() to wrap
enetc_imdio_remove() (improve code maintenance) and call it
on bailout and remove paths.
Fixes: 975d183ef0 ("net: enetc: Initialize SerDes for SGMII and USXGMII protocols")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove casting the values returned by memory allocation function.
Coccinelle emits WARNING: casting value returned by memory allocation
unction to (struct roce_destroy_qp_req_output_params *) is useless.
This issue was detected by using the Coccinelle software.
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The VSC7514 is marketed as a 10-port switch, however it has 11 physical
ports (0->10) in the block diagram:
https://www.microsemi.com/product-directory/ethernet-switches/3992-vsc7514
(also in the device tree at arch/mips/boot/dts/mscc/ocelot.dtsi)
Additionally, by architecture it has one more entry in the analyzer
block, situated right after the physical ports, for the CPU port module.
This is not a physical port, it only represents a channel for frame
injection and extraction. That entry for the CPU port is at index 11 in
the analyzer.
When the register groups for QSYS_SWITCH_PORT_MODE, SYS_PORT_MODE and
SYS_PAUSE_CFG are declared to be replicated 11 times, the 11th entry in
the array of regfields is not initialized, so the CPU port module is not
initialized either.
The documentation of QSYS_SWITCH_PORT_MODE for VSC7514 also says that
this register group is replicated 12 times, so this patch is simply
reflecting that and not introducing any further inconsistency.
Fixes: 886e1387c7 ("net: mscc: ocelot: convert QSYS_SWITCH_PORT_MODE and SYS_PORT_MODE to regfields")
Fixes: 541132f096 ("net: mscc: ocelot: convert SYS_PAUSE_CFG register access to regfield")
Reported-by: Bryan Whitehead <bryan.whitehead@microchip.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add some new interface values and update a few more descriptions.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can prevent potential incorrect DMA access attempts from the
NIC by enabling bus-master after the reset, and by disabling
bus-master earlier in cleanup.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix up our comparison to better handle a potential (but largely
unlikely) wrap around.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the host system's udev fails to set a new name for the
network port, there is no NETDEV_CHANGENAME event to trigger
the driver to send the name down to the firmware. It is safe
to set the lif name multiple times, so we add a call early on
to set the default netdev name to be sure the FW has something
to use in its internal debug logging. Then when udev gets
around to changing it we can update it to the actual name the
system will be using.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change from using hardcoded MTU limits and instead use the
firmware defined limits. The value from the LIF attributes is
the frame size, so we take off the header size to convert to
MTU size.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
React to TC_SETUP_QDISC_TBF and configure the egress shaper as
appropriate with the maximum rate and burst size requested by the user.
TBF can only be offloaded on DPAA2 when it's the root qdisc, ie it's a
per port shaper.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the necessary API (dpni_set_tx_shaping) for configuring the rate and
burst size of a per port shaper in DPAA2.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the setup done for MQPRIO into a separate function so that
with the addition of another offload we do not crowd
dpaa2_eth_setup_tc(). After this restructuring it's easier to see what
is supported in terms of Qdisc offloading.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For most chip versions this has been added already. Allow also for
RTL8125A to enable ASPM.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New devices add a new hardware acceleration engine, which adds some
restrictions to the driver.
Metadata descriptor must be present for each packet and the maximum
burst size between two doorbells is now limited to a number
advertised by the device.
This patch adds:
1. A handshake protocol between the driver and the device, so the
device will enable the accelerated queues only when both sides
support it.
2. The driver support for the new acceleration engine:
2.1. Send metadata descriptor for each Tx packet.
2.2. Limit the number of packets sent between doorbells.(*)
(*) A previous driver implementation of this feature was comitted in
commit 05d62ca218 ("net: ena: add handling of llq max tx burst size")
however the design of the interface between the driver and device
changed since then. This change is reflected in this commit.
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the ENA device resets to recover from some error state, all LLQ
configuration values are reset to their defaults, because LLQ is
initialized only once during ena_probe().
Changes in this commit:
1. Move the LLQ configuration process into ena_init_device()
which is called from both ena_probe() and ena_restore_device(). This
way, LLQ setup configurations that are different from the default
values will survive resets.
2. Extract the LLQ bar mapping to ena_map_llq_bar(),
and call once in the lifetime of the driver from ena_probe(),
since there is no need to unmap and map the LLQ bar again every reset.
3. Map the LLQ bar if it exists, regardless if initialization of LLQ
placement policy (ENA_ADMIN_PLACEMENT_POLICY_DEV) succeeded
or not. Initialization might fail the first time, falling back to the
ENA_ADMIN_PLACEMENT_POLICY_HOST placement policy, but later succeed
after device reset, in which case the LLQ bar needs to be mapped
already.
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the rss_configurable_function_key bit to driver_supported_feature.
This bit tells the device that the driver in question supports the
retrieving and updating of RSS function and hash key, and therefore
the device should allow RSS function and key manipulation.
This commit turns on device support for hash key and RSS function
management. Without this commit this feature is turned off at the
device and appears to the user as unsupported.
This commit concludes the following series of already merged commits:
commit 0af3c4e2ea ("net: ena: changes to RSS hash key allocation")
commit c1bd17e51c ("net: ena: change default RSS hash function to Toeplitz")
commit f66c2ea3b1 ("net: ena: allow setting the hash function without changing the key")
commit e9a1de378d ("net: ena: fix error returning in ena_com_get_hash_function()")
commit 80f8443fcd ("net: ena: avoid unnecessary admin command when RSS function set fails")
commit 6a4f7dc82d ("net: ena: rss: do not allocate key when not supported")
commit 0d1c3de7b8 ("net: ena: fix incorrect default RSS key")
The above commits represent the last part of the implementation of
this feature, and with them merged the feature can be enabled
in the device.
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for traffic mirroring, where the hardware reads the
buffer from the instance memory directly.
Traffic Mirroring needs access to the rx buffers in the instance.
To have this access, this patch:
1. Changes the code to map and unmap the rx buffers bidirectionally.
2. Enables the relevant bit in driver_supported_features to indicate
to the FW that this driver supports traffic mirroring.
Rx completion is not generated until mirroring is done to avoid
the situation where the driver changes the buffer before it is
mirrored.
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The size of the admin statistics in ena_com_stats_admin is changed
from 32bit to 64bit so to align with the sizes of the other statistics
in the driver (i.e. rx_stats, tx_stats and ena_stats_dev).
This is done as part of an effort to create a unified API to read
statistics.
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
gcc 4.8 reports a warning when initializing with = {0}.
Dropping the "0" from the braces fixes the issue.
This fix is not ANSI compatible but is allowed by gcc.
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
