Name the Pin Function Controller subnode for SCIF0 after its device
name, instead of after the serial port alias.
This avoids conflicts when enabling support for more serial ports later,
either here or in a DT overlay.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Warning (unit_address_vs_reg): Node /memory has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): Node /fixedregulator@0 has a unit name, but no reg property
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
On the BOCK-W development board, the RTS and CTS pins of the console
SCIF0 are wired to the "product serial" connector. Reflect this in the
DTS by adding the "uart-has-rtscts" property to the scif0 device node.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Since 16ccaf5bb5 ("pinctrl: sh-pfc: Accept standard function, pins and
groups properties") renesas pfc drivers accept generic "function", "pins"
and "groups" properties.
This patch updates the bockw device tree to use the generic properties.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add and enable the external crystal for the SCIF_CLK and its pinctrl, to
be used by the Baud Rate Generator for External Clock (BRG) on (H)SCIF.
This increases the range and accuracy of supported baud rates.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As of commit e488ca9f8d ("doc: dt: mtd: partitions: add compatible
property to "partitions" node"), the "partitions" subnode of an SPI
FLASH device node must have a compatible property. The partitions are no
longer detected if it is not present.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Drop the "console=" parameter from the kernel command line, as it's no
longer needed for DT-based platforms.
Add serial port config to chosen/stdout-path.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The default value of #sound-dai-cells in r8a7778.dtsi is one, while
the /sound/simple-audio-card,cpu device node in r8a7778-bockw.dts uses a
phandle without any extra cells ("<&rcar_sound>"), causing:
/sound/simple-audio-card,cpu: arguments longer than property
asoc-simple-card sound: parse error -22
asoc-simple-card: probe of sound failed with error -22
Override #sound-dai-cells to zero to fix this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As of commits 5cfdedb7b9 ("mtd: ofpart: move ofpart partitions to a
dedicated dt node") and fe2585e9c2 ("doc: dt: mtd: support partitions
in a special 'partitions' subnode"), having partitions as direct subnodes
of an mtd device is discouraged. Hence move the SPI FLASH partition to a
"partitions" subnode.
Based on similar work for the koelsch board by Geert Uytterhoeven.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Ensures that the pull-ups for pins SD0_CD and SD0_WP are enabled.
This is one of two features from the DT reference platform that are
still missing in MP.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Spansion s25fl008k is compatible with "nor-jedec". Hence add the
"nor-jedec" compatible value, so the driver can bind against the generic
name, cfr. commit 8ff16cf77c ("Documentation: devicetree: m25p80:
add "nor-jedec" binding").
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Adds sound card using the ak4643 codec.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Sets the extal clock to the frequency of the oscillator installed by
default (33 MHz).
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Move the Ethernet node to the new BSC node, as its connected to the
Bus State Controller.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
[horms: dropped compat string changes as they seem out of scope]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Adds pin control info for USB host and video-in devices.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This moves everything to the legacy dts that is missing there to make it
suitable for use with multiplatform.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
In order to allow usage of the preprocessor in the SoC device tree
sources, switch from /include/ to #include.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The shmobile DT files available in the kernel are reference
implementations intended to be used as sample code, as well as for
development. As such, it makes sense to mount the root file system in
read/write mode by default.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
"ip" and "root" settings are useful for development
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add basic Bock-W board support
More devices will be added on top of this patch after
PICNTRL and clock framework are in better shape.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
