[ Upstream commit 0fb782b5d5 ]
The Lenovo Yoga Tablet 2 Pro 1380 model is the exception to the rule that
devices which use the Crystal Cove PMIC without using ACPI for battery and
AC power_supply class support use the USB-phy for charger detection.
Unlike the Lenovo Yoga Tablet 2 830 / 1050 models this model has an extra
LC824206XA Micro USB switch which does the charger detection.
Add a DMI quirk to not set the "linux,phy_charger_detect" property on
the 1380 model. This quirk matches on the BIOS version to differentiate
the 1380 model from the 830 and 1050 models which otherwise have
the same DMI strings.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20240406140127.17885-1-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 1d26ba0944 upstream.
Currently all controller IP/revisions except DWC3_usb3 >= 310a
wait 1ms unconditionally for ENDXFER completion when IOC is not
set. This is because DWC_usb3 controller revisions >= 3.10a
supports GUCTL2[14: Rst_actbitlater] bit which allows polling
CMDACT bit to know whether ENDXFER command is completed.
Consider a case where an IN request was queued, and parallelly
soft_disconnect was called (due to ffs_epfile_release). This
eventually calls stop_active_transfer with IOC cleared, hence
send_gadget_ep_cmd() skips waiting for CMDACT cleared during
EndXfer. For DWC3 controllers with revisions >= 310a, we don't
forcefully wait for 1ms either, and we proceed by unmapping the
requests. If ENDXFER didn't complete by this time, it leads to
SMMU faults since the controller would still be accessing those
requests.
Fix this by ensuring ENDXFER completion by adding 1ms delay in
__dwc3_stop_active_transfer() unconditionally.
Cc: stable@vger.kernel.org
Fixes: b353eb6dc2 ("usb: dwc3: gadget: Skip waiting for CMDACT cleared during endxfer")
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20240502044103.1066350-1-quic_prashk@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6d73572206 upstream.
GUSB3PIPECTL.SUSPENDENABLE and GUSB2PHYCFG.SUSPHY should be cleared
during initialization. Suspend during initialization can result in
undefined behavior due to clock synchronization failure, which often
seen as core soft reset timeout.
The programming guide recommended these bits to be cleared during
initialization for DWC_usb3.0 version 1.94 and above (along with
DWC_usb31 and DWC_usb32). The current check in the driver does not
account if it's set by default setting from coreConsultant.
This is especially the case for DRD when switching mode to ensure the
phy clocks are available to change mode. Depending on the
platforms/design, some may be affected more than others. This is noted
in the DWC_usb3x programming guide under the above registers.
Let's just disable them during driver load and mode switching. Restore
them when the controller initialization completes.
Note that some platforms workaround this issue by disabling phy suspend
through "snps,dis_u3_susphy_quirk" and "snps,dis_u2_susphy_quirk" when
they should not need to.
Cc: stable@vger.kernel.org
Fixes: 9ba3aca8fe ("usb: dwc3: Disable phy suspend after power-on reset")
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20da4e5a0c4678c9587d3da23f83bdd6d77353e9.1713394973.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f121531703 upstream.
Intel Arrow Lake CPU uses the Meteor Lake ID with this
controller (the controller that's part of the Intel Arrow
Lake chipset (PCH) does still have unique PCI ID).
Fixes: de4b5b28c8 ("usb: dwc3: pci: add support for the Intel Arrow Lake-H")
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20240312115008.1748637-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f9aa41130a upstream.
If the device is configured for system wakeup, then make sure that the
xHCI driver knows about it and make sure to permit wakeup only at the
appropriate time.
For host mode, if the controller goes through the dwc3 code path, then a
child xHCI platform device is created. Make sure the platform device
also inherits the wakeup setting for xHCI to enable remote wakeup.
For device mode, make sure to disable system wakeup if no gadget driver
is bound. We may experience unwanted system wakeup due to the wakeup
signal from the controller PMU detecting connection/disconnection when
in low power (D3). E.g. In the case of Steam Deck, the PCI PME prevents
the system staying in suspend.
Cc: stable@vger.kernel.org
Reported-by: Guilherme G. Piccoli <gpiccoli@igalia.com>
Closes: https://lore.kernel.org/linux-usb/70a7692d-647c-9be7-00a6-06fc60f77294@igalia.com/T/#mf00d6669c2eff7b308d1162acd1d66c09f0853c7
Fixes: d07e8819a0 ("usb: dwc3: add xHCI Host support")
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Tested-by: Sanath S <Sanath.S@amd.com>
Tested-by: Guilherme G. Piccoli <gpiccoli@igalia.com> # Steam Deck
Link: https://lore.kernel.org/r/667cfda7009b502e08462c8fb3f65841d103cc0a.1709865476.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6661befe41 ]
As runtime PM is enabled, the module can be runtime
suspended when .remove() is called.
Do a pm_runtime_get_sync() to make sure module is active
before doing any register operations.
Doing a pm_runtime_put_sync() should disable the refclk
so no need to disable it again.
Fixes the below warning at module removel.
[ 39.705310] ------------[ cut here ]------------
[ 39.710004] clk:162:3 already disabled
[ 39.713941] WARNING: CPU: 0 PID: 921 at drivers/clk/clk.c:1090 clk_core_disable+0xb0/0xb8
We called of_platform_populate() in .probe() so call the
cleanup function of_platform_depopulate() in .remove().
Get rid of the now unnnecessary dwc3_ti_remove_core().
Without this, module re-load doesn't work properly.
Fixes: e8784c0aec ("drivers: usb: dwc3: Add AM62 USB wrapper driver")
Cc: stable@vger.kernel.org # v5.19+
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20240227-for-v6-9-am62-usb-errata-3-0-v4-1-0ada8ddb0767@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 61a348857e upstream.
In current scenario if Plug-out and Plug-In performed continuously
there could be a chance while checking for dwc->gadget_driver in
dwc3_gadget_suspend, a NULL pointer dereference may occur.
Call Stack:
CPU1: CPU2:
gadget_unbind_driver dwc3_suspend_common
dwc3_gadget_stop dwc3_gadget_suspend
dwc3_disconnect_gadget
CPU1 basically clears the variable and CPU2 checks the variable.
Consider CPU1 is running and right before gadget_driver is cleared
and in parallel CPU2 executes dwc3_gadget_suspend where it finds
dwc->gadget_driver which is not NULL and resumes execution and then
CPU1 completes execution. CPU2 executes dwc3_disconnect_gadget where
it checks dwc->gadget_driver is already NULL because of which the
NULL pointer deference occur.
Cc: stable@vger.kernel.org
Fixes: 9772b47a4c ("usb: dwc3: gadget: Fix suspend/resume during device mode")
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Uttkarsh Aggarwal <quic_uaggarwa@quicinc.com>
Link: https://lore.kernel.org/r/20240119094825.26530-1-quic_uaggarwa@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 817349b6d2 upstream.
Upstream commit bac1ec5514 ("usb: xhci: Set quirk for
XHCI_SG_TRB_CACHE_SIZE_QUIRK") introduced a new quirk in XHCI
which fixes XHC timeout, which was seen on synopsys XHCs while
using SG buffers. But the support for this quirk isn't present
in the DWC3 layer.
We will encounter this XHCI timeout/hung issue if we run iperf
loopback tests using RTL8156 ethernet adaptor on DWC3 targets
with scatter-gather enabled. This gets resolved after enabling
the XHCI_SG_TRB_CACHE_SIZE_QUIRK. This patch enables it using
the xhci device property since its needed for DWC3 controller.
In Synopsys DWC3 databook,
Table 9-3: xHCI Debug Capability Limitations
Chained TRBs greater than TRB cache size: The debug capability
driver must not create a multi-TRB TD that describes smaller
than a 1K packet that spreads across 8 or more TRBs on either
the IN TR or the OUT TR.
Cc: stable@vger.kernel.org #5.11
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20240116055816.1169821-2-quic_prashk@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit afe28cd686 upstream.
This reverts commit e835c0a4e2.
Don't omit soft-reset. During initialization, the driver may need to
perform a soft reset to ensure the phy is ready when the controller
updates the GCTL.PRTCAPDIR or other settings by issuing phy soft-reset.
Many platforms often have access to DCTL register for soft-reset despite
being host-only. If there are actual reported issues from the platforms
that don't expose DCTL registers, then we will need to revisit (perhaps
to teach dwc3 to perform xhci's soft-reset USBCMD.HCRST).
Cc: <stable@vger.kernel.org>
Fixes: e835c0a4e2 ("usb: dwc3: don't reset device side if dwc3 was configured as host-only")
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/7668ab11a48f260820825274976eb41fec7f54d1.1703282469.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3c7af52c76 upstream.
There is a scenario where DWC3 runtime suspend is blocked due to the
dwc->connected flag still being true while PM usage_count is zero after
DWC3 giveback is completed and the USB gadget session is being terminated.
This leads to a case where nothing schedules a PM runtime idle for the
device.
The exact condition is seen with the following sequence:
1. USB bus reset is issued by the host
2. Shortly after, or concurrently, a USB PD DR SWAP request is received
(sink->source)
3. USB bus reset event handler runs and issues
dwc3_stop_active_transfers(), and pending transfer are stopped
4. DWC3 usage_count decremented to 0, and runtime idle occurs while
dwc->connected == true, returns -EBUSY
5. DWC3 disconnect event seen, dwc->connected set to false due to DR
swap handling
6. No runtime idle after this point
Address this by issuing an asynchronous PM runtime idle call after the
disconnect event is completed, as it modifies the dwc->connected flag,
which is what blocks the initial runtime idle.
Fixes: fc8bb91bc8 ("usb: dwc3: implement runtime PM")
Cc: <stable@vger.kernel.org>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20240103214946.2596-1-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 730e12fbec upstream.
Current EP0 dequeue path will share the same as other EPs. However, there
are some special considerations that need to be made for EP0 transfers:
- EP0 transfers never transition into the started_list
- EP0 only has one active request at a time
In case there is a vendor specific control message for a function over USB
FFS, then there is no guarantee on the timeline which the DATA/STATUS stage
is responded to. While this occurs, any attempt to end transfers on
non-control EPs will end up having the DWC3_EP_DELAY_STOP flag set, and
defer issuing of the end transfer command. If the USB FFS application
decides to timeout the control transfer, or if USB FFS AIO path exits, the
USB FFS driver will issue a call to usb_ep_dequeue() for the ep0 request.
In case of the AIO exit path, the AIO FS blocks until all pending USB
requests utilizing the AIO path is completed. However, since the dequeue
of ep0 req does not happen properly, all non-control EPs with the
DWC3_EP_DELAY_STOP flag set will not be handled, and the AIO exit path will
be stuck waiting for the USB FFS data endpoints to receive a completion
callback.
Fix is to utilize dwc3_ep0_reset_state() in the dequeue API to ensure EP0
is brought back to the SETUP state, and ensures that any deferred end
transfer commands are handled. This also will end any active transfers
on EP0, compared to the previous implementation which directly called
giveback only.
Fixes: fcd2def663 ("usb: dwc3: gadget: Refactor dwc3_gadget_ep_dequeue")
Cc: stable <stable@kernel.org>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20231206201814.32664-1-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e9d40b215e upstream.
Current implementation blocks the running operations when Plug-out and
Plug-In is performed continuously, process gets stuck in
dwc3_thread_interrupt().
Code Flow:
CPU1
->Gadget_start
->dwc3_interrupt
->dwc3_thread_interrupt
->dwc3_process_event_buf
->dwc3_process_event_entry
->dwc3_endpoint_interrupt
->dwc3_ep0_interrupt
->dwc3_ep0_inspect_setup
->dwc3_ep0_stall_and_restart
By this time if pending_list is not empty, it will get the next request
on the given list and calls dwc3_gadget_giveback which will unmap request
and call its complete() callback to notify upper layers that it has
completed. Currently dwc3_gadget_giveback status is set to -ECONNRESET,
whereas it should be -ESHUTDOWN based on condition if not dwc->connected
is true.
Cc: <stable@vger.kernel.org>
Fixes: d742220b35 ("usb: dwc3: ep0: giveback requests on stall_and_restart")
Signed-off-by: Uttkarsh Aggarwal <quic_uaggarwa@quicinc.com>
Link: https://lore.kernel.org/r/20231222094704.20276-1-quic_uaggarwa@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 41f5a09732 upstream.
The Qualcomm glue driver is overriding the interrupt trigger types
defined by firmware when requesting the wakeup interrupts during probe.
This can lead to a failure to map the DP/DM wakeup interrupts after a
probe deferral as the firmware defined trigger types do not match the
type used for the initial mapping:
irq: type mismatch, failed to map hwirq-14 for interrupt-controller@b220000!
irq: type mismatch, failed to map hwirq-15 for interrupt-controller@b220000!
Fix this by not overriding the firmware provided trigger types when
requesting the wakeup interrupts.
Fixes: a4333c3a6b ("usb: dwc3: Add Qualcomm DWC3 glue driver")
Cc: stable@vger.kernel.org # 4.18
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Link: https://lore.kernel.org/r/20231120161607.7405-3-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9feefbf57d upstream.
Make sure to remove the software node also on (ACPI) probe errors to
avoid leaking the underlying resources.
Note that the software node is only used for ACPI probe so the driver
unbind tear down is updated to match probe.
Fixes: 8dc6e6dd1b ("usb: dwc3: qcom: Constify the software node")
Cc: stable@vger.kernel.org # 5.12
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Andrew Halaney <ahalaney@redhat.com>
Link: https://lore.kernel.org/r/20231117173650.21161-3-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 10d510abd0 upstream.
The default mode, configurable by DT, shall be set before usb role switch
driver is registered. Otherwise there is a race between default mode
and mode set by usb role switch driver.
Fixes: 98ed256a4d ("usb: dwc3: Add support for role-switch-default-mode binding")
Cc: stable <stable@kernel.org>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20231025095110.2405281-1-alexander.stein@ew.tq-group.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9cf87666fc ]
Make sure to free the "urs" platform device, which is created for some
ACPI platforms, on probe errors and on driver unbind.
Compile-tested only.
Fixes: c25c210f59 ("usb: dwc3: qcom: add URS Host support for sdm845 ACPI boot")
Cc: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Acked-by: Andrew Halaney <ahalaney@redhat.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Link: https://lore.kernel.org/r/20231117173650.21161-4-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 51392a1879 ]
The driver needs to deregister and free the newly allocated dwc3 core
platform device on ACPI probe errors (e.g. probe deferral) and on driver
unbind but instead it leaked those resources while erroneously dropping
a reference to the parent platform device which is still in use.
For OF probing the driver takes a reference to the dwc3 core platform
device which has also always been leaked.
Fix the broken ACPI tear down and make sure to drop the dwc3 core
reference for both OF and ACPI.
Fixes: 8fd95da2cf ("usb: dwc3: qcom: Release the correct resources in dwc3_qcom_remove()")
Fixes: 2bc02355f8 ("usb: dwc3: qcom: Add support for booting with ACPI")
Fixes: a4333c3a6b ("usb: dwc3: Add Qualcomm DWC3 glue driver")
Cc: stable@vger.kernel.org # 4.18
Cc: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Cc: Lee Jones <lee@kernel.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Acked-by: Andrew Halaney <ahalaney@redhat.com>
Link: https://lore.kernel.org/r/20231117173650.21161-2-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 9cf87666fc ("USB: dwc3: qcom: fix ACPI platform device leak")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e72fc8d6a1 ]
In Synopsys's dwc3 data book:
To avoid underrun and overrun during the burst, in a high-latency bus
system (like USB), threshold and burst size control is provided through
GTXTHRCFG and GRXTHRCFG registers.
In Realtek DHC SoC, DWC3 USB 3.0 uses AHB system bus. When dwc3 is
connected with USB 2.5G Ethernet, there will be overrun problem.
Therefore, setting TX/RX thresholds can avoid this issue.
Signed-off-by: Stanley Chang <stanley_chang@realtek.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20230912041904.30721-1-stanley_chang@realtek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
When there's phy initialization, we need to initiate a soft-reset
sequence. That's done through USBCMD.HCRST in the xHCI driver and its
initialization, However, the dwc3 driver may modify core configs before
the soft-reset. This may result in some connection instability. So,
ensure the phy is ready before the controller updates the GCTL.PRTCAPDIR
or other settings by issuing phy soft-reset.
Note that some host-mode configurations may not expose device registers
to initiate the controller soft-reset (via DCTL.CoreSftRst). So we reset
through GUSB3PIPECTL and GUSB2PHYCFG instead.
Cc: stable@vger.kernel.org
Fixes: e835c0a4e2 ("usb: dwc3: don't reset device side if dwc3 was configured as host-only")
Reported-by: Kenta Sato <tosainu.maple@gmail.com>
Closes: https://lore.kernel.org/linux-usb/ZPUciRLUcjDywMVS@debian.me/
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Tested-by: Kenta Sato <tosainu.maple@gmail.com>
Link: https://lore.kernel.org/r/70aea513215d273669152696cc02b20ddcdb6f1a.1694564261.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add Exynos850 compatible string and associated driver data. Only two
clocks are needed for this SoC:
- bus_early: bus clock needed for registers access
- ref: USB 2.0 DRD reference clock (50 MHz)
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230819031731.22618-4-semen.protsenko@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove unnecessary platform_set_drvdata(..., NULL) in ->remove(),
the driver_data will be cleared in device_unbind_cleanup() after
calling ->remove() in driver call code.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20230810134710.114356-1-yangyingliang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Device connected to usb otg port of GXL-based boards can not be
recognised after resumption, doesn't recover even if disconnect and
reconnect the device. dmesg shows it disconnects during resumption.
[ 41.492911] usb 1-2: USB disconnect, device number 3
[ 41.499346] usb 1-2: unregistering device
[ 41.511939] usb 1-2: unregistering interface 1-2:1.0
Calling usb_post_init() will fix this issue, and it's tested and
verified on libretech's aml-s905x-cc board.
Cc: stable@vger.kernel.org # v5.8+
Fixes: c99993376f ("usb: dwc3: Add Amlogic G12A DWC3 glue")
Signed-off-by: Luke Lu <luke.lu@libre.computer>
Acked-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230809212911.18903-1-luke.lu@libre.computer
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If dwc3 is runtime suspended we defer processing the event buffer
until resume, by setting the pending_events flag. Set this flag before
triggering resume to avoid race with the runtime resume callback.
While handling the pending events, in addition to checking the event
buffer we also need to process it. Handle this by explicitly calling
dwc3_thread_interrupt(). Also balance the runtime pm get() operation
that triggered this processing.
Cc: stable@vger.kernel.org
Fixes: fc8bb91bc8 ("usb: dwc3: implement runtime PM")
Signed-off-by: Elson Roy Serrao <quic_eserrao@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20230801192658.19275-1-quic_eserrao@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Assign copyright to indicate driver rewrite is done for RACOM s.r.o.
As David no longer works for Marvell (Cavium), I'm to blame for breakage.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Acked-by: David Daney <daviddaney@microsoft.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Link: https://lore.kernel.org/r/ZMeAAYx6Z3hlQBNQ@lenoch
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It might be interesting to know control register value in case
clock fails to enable.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/ZMd/5OX9szEMnhQH@lenoch
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Parse and verify device tree node first, then setup UCTL bridge
using verified values. This avoids needless allocations
in case DT misconfiguration was found in the middle of setup.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/ZMd/x3MHA4/QowMO@lenoch
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Power gpio configuration is done from the middle of
dwc3_octeon_clocks_start leaving hardware in half-initialized
state if it fails. As that indicates dwc3_octeon_clocks_start
does more than just initialize the clocks rename it appropriately
and verify power gpio configuration in advance at the beginning
of device probe.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/ZMd/oMRx8ze22/kK@lenoch
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pass dwc3_octeon instead of just the base. It fits with the
function names and it requires less change in the future if
access to dwc3_octeon is needed.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/ZMd/gt58laSlqAAT@lenoch
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While driver is intended to run on 64bit machines, it is compile time
tested for 32bit targets as well. Here shift count overflow is reported
for bits greater than 31, so use _ULL versions of BIT and GENMASK macros
to silence these warnings.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202307260537.MROrhVNM-lkp@intel.com/
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/ZMd/aa2ncz6tJGNU@lenoch
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DWC3 as implemented in Cavium SoC is using UCTL bridge unit
between I/O interconnect and USB controller.
Currently there is no bond with dwc3 core code, so if anything goes
wrong in UCTL setup dwc3 is left in reset, which leads to bus error
while trying to read any device register. Thus any failure in UCTL
initialization ends with kernel panic.
To avoid this move Octeon DWC3 glue code from arch/mips and make it
proper glue driver which is used instead of dwc3-of-simple.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Acked-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/ZMd/ReyiY7wS6DvN@lenoch
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need the USB fixes in here for testing and for other patches to be
applied on top of.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hardware based on the Bay Trail / BYT SoCs require an external ULPI phy for
USB device-mode. The phy chip usually has its 'reset' and 'chip select'
lines connected to GPIOs described by ACPI fwnodes in the DSDT table.
Because of hardware with missing ACPI resources for the 'reset' and 'chip
select' GPIOs commit 5741022cbd ("usb: dwc3: pci: Add GPIO lookup table
on platforms without ACPI GPIO resources") introduced a fallback
gpiod_lookup_table with hard-coded mappings for Bay Trail devices.
However there are existing Bay Trail based devices, like the National
Instruments cRIO-903x series, where the phy chip has its 'reset' and
'chip-select' lines always asserted in hardware via resistor pull-ups. On
this hardware the phy chip is always enabled and the ACPI dsdt table is
missing information not only for the 'chip-select' and 'reset' lines but
also for the BYT GPIO controller itself "INT33FC".
With the introduction of the gpiod_lookup_table initializing the USB
device-mode on these hardware now errors out. The error comes from the
gpiod_get_optional() calls in dwc3_pci_quirks() which will now return an
-ENOENT error due to the missing ACPI entry for the INT33FC gpio controller
used in the aforementioned table.
This hardware used to work before because gpiod_get_optional() will return
NULL instead of -ENOENT if no GPIO has been assigned to the requested
function. The dwc3_pci_quirks() code for setting the 'cs' and 'reset' GPIOs
was then skipped (due to the NULL return). This is the correct behavior in
cases where the phy chip is hardwired and there are no GPIOs to control.
Since the gpiod_lookup_table relies on the presence of INT33FC fwnode
in ACPI tables only add the table if we know the entry for the INT33FC
gpio controller is present. This allows Bay Trail based devices with
hardwired dwc3 ULPI phys to continue working.
Fixes: 5741022cbd ("usb: dwc3: pci: Add GPIO lookup table on platforms without ACPI GPIO resources")
Cc: stable <stable@kernel.org>
Signed-off-by: Gratian Crisan <gratian.crisan@ni.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230726184555.218091-2-gratian.crisan@ni.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rename dwc3_data to dwc3_am62 to make it consistent with other
glue drivers, it's clearer that this is am62's specific.
While there, do the same for data variable.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Link: https://lore.kernel.org/r/ZLKoHhJvT+Y6aM+C@lenoch
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Acked-by: Herve Codina <herve.codina@bootlin.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230718143027.1064731-1-robh@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit b138e23d3d.
AutoRetry has been found to sometimes cause controller freezes when
communicating with buggy USB devices.
This controller feature allows the controller in host mode to send
non-terminating/burst retry ACKs instead of terminating retry ACKs
to devices when a transaction error (CRC error or overflow) occurs.
Unfortunately, if the USB device continues to respond with a CRC error,
the controller will not complete endpoint-related commands while it
keeps trying to auto-retry. [3] The xHCI driver will notice this once
it tries to abort the transfer using a Stop Endpoint command and
does not receive a completion in time. [1]
This situation is reported to dmesg:
[sda] tag#29 uas_eh_abort_handler 0 uas-tag 1 inflight: CMD IN
[sda] tag#29 CDB: opcode=0x28 28 00 00 69 42 80 00 00 48 00
xhci-hcd: xHCI host not responding to stop endpoint command
xhci-hcd: xHCI host controller not responding, assume dead
xhci-hcd: HC died; cleaning up
Some users observed this problem on an Odroid HC2 with the JMS578
USB3-to-SATA bridge. The issue can be triggered by starting
a read-heavy workload on an attached SSD. After a while, the host
controller would die and the SSD would disappear from the system. [1]
Further analysis by Synopsys determined that controller revisions
other than the one in Odroid HC2 are also affected by this.
The recommended solution was to disable AutoRetry altogether.
This change does not have a noticeable performance impact. [2]
Revert the enablement commit. This will keep the AutoRetry bit in
the default state configured during SoC design [2].
Fixes: b138e23d3d ("usb: dwc3: core: Enable AutoRetry feature in the controller")
Link: https://lore.kernel.org/r/a21f34c04632d250cd0a78c7c6f4a1c9c7a43142.camel@gmail.com/ [1]
Link: https://lore.kernel.org/r/20230711214834.kyr6ulync32d4ktk@synopsys.com/ [2]
Link: https://lore.kernel.org/r/20230712225518.2smu7wse6djc7l5o@synopsys.com/ [3]
Cc: stable@vger.kernel.org
Cc: Mauro Ribeiro <mauro.ribeiro@hardkernel.com>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Suggested-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Jakub Vanek <linuxtardis@gmail.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20230714122419.27741-1-linuxtardis@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit c4a5153e87 ("usb: dwc3: core: Power-off core/PHYs on
system_suspend in host mode") replaces check for HOST only dr_mode with
current_dr_role. But during booting, the current_dr_role isn't
initialized, thus the device side reset is always issued even if dwc3
was configured as host-only. What's more, on some platforms with host
only dwc3, aways issuing device side reset by accessing device register
block can cause kernel panic.
Fixes: c4a5153e87 ("usb: dwc3: core: Power-off core/PHYs on system_suspend in host mode")
Cc: stable <stable@kernel.org>
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20230627162018.739-1-jszhang@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the big set of USB and Thunderbolt driver updates for 6.5-rc1.
Included in here are:
- Lots of USB4/Thunderbolt additions and updates for new hardware
types and fixes as people are starting to get access to the hardware
in the wild
- new gadget controller driver, cdns2, added
- new typec drivers added
- xhci driver updates
- typec driver updates
- usbip driver fixes
- usb-serial driver updates and fixes
- lots of smaller USB driver updates
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZKKcVw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynEIQCgzJgnMCB81mirXlY1ZpCSDFqN8KIAnjRc27/1
vnUzldMQGY/FiS549gD9
=G3yz
-----END PGP SIGNATURE-----
Merge tag 'usb-6.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt driver updates from Greg KH:
"Here is the big set of USB and Thunderbolt driver updates for 6.5-rc1.
Included in here are:
- Lots of USB4/Thunderbolt additions and updates for new hardware
types and fixes as people are starting to get access to the
hardware in the wild
- new gadget controller driver, cdns2, added
- new typec drivers added
- xhci driver updates
- typec driver updates
- usbip driver fixes
- usb-serial driver updates and fixes
- lots of smaller USB driver updates
All of these have been in linux-next for a while with no reported
problems"
* tag 'usb-6.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (265 commits)
usb: host: xhci-plat: Set XHCI_STATE_REMOVING before resuming XHCI HC
usb: host: xhci: Do not re-initialize the XHCI HC if being removed
usb: typec: nb7vpq904m: fix CONFIG_DRM dependency
usbip: usbip_host: Replace strlcpy with strscpy
usb: dwc3: gadget: Propagate core init errors to UDC during pullup
USB: serial: option: add LARA-R6 01B PIDs
usb: ulpi: Make container_of() no-op in to_ulpi_dev()
usb: gadget: legacy: fix error return code in gfs_bind
usb: typec: fsa4480: add support for Audio Accessory Mode
usb: typec: fsa4480: rework mux & switch setup to handle more states
usb: typec: ucsi: call typec_set_mode on non-altmode partner change
USB: gadget: f_hid: make hidg_class a static const structure
USB: gadget: f_printer: make usb_gadget_class a static const structure
USB: mon: make mon_bin_class a static const structure
USB: gadget: udc: core: make udc_class a static const structure
USB: roles: make role_class a static const structure
dt-bindings: usb: dwc3: Add interrupt-names property support for wakeup interrupt
dt-bindings: usb: Add StarFive JH7110 USB controller
dt-bindings: usb: dwc3: Add IPQ9574 compatible
usb: cdns2: Fix spelling mistake in a trace message "Wakupe" -> "Wakeup"
...
In scenarios where pullup relies on resume (get sync) to initialize
the controller and set the run stop bit, then core_init is followed by
gadget_resume which will eventually set run stop bit.
But in cases where the core_init fails, the return value is not sent
back to udc appropriately. So according to UDC the controller has
started but in reality we never set the run stop bit.
On systems like Android, there are uevents sent to HAL depending on
whether the configfs_bind / configfs_disconnect were invoked. In the
above mentioned scnenario, if the core init fails, the run stop won't
be set and the cable plug-out won't result in generation of any
disconnect event and userspace would never get any uevent regarding
cable plug out and we never call pullup(0) again. Furthermore none of
the next Plug-In/Plug-Out's would be known to configfs.
Return back the appropriate result to UDC to let the userspace/
configfs know that the pullup failed so they can take appropriate
action.
Fixes: 77adb8bdf4 ("usb: dwc3: gadget: Allow runtime suspend if UDC unbinded")
Cc: stable <stable@kernel.org>
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Message-ID: <20230618120949.14868-1-quic_kriskura@quicinc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If dwc3_meson_g12a_otg_init() fails, resources allocated by the previous
of_platform_populate() call should be released, as already done in the
error handling path.
Fixes: 1e355f21d3 ("usb: dwc3: Add Amlogic A1 DWC3 glue")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Message-ID: <9d28466de1808ccc756b4cc25fc72c482d133d13.1686403934.git.christophe.jaillet@wanadoo.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Update to using dev_err_probe() throughout to reduce spam and log useful
information in devices_deferred.
Signed-off-by: Andrew Halaney <ahalaney@redhat.com>
Message-ID: <20230605193625.63187-1-ahalaney@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If dwc3_qcom_create_urs_usb_platdev() fails, some resources still need to
be released, as already done in the other error handling path of the
probe.
Fixes: c25c210f59 ("usb: dwc3: qcom: add URS Host support for sdm845 ACPI boot")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Message-ID: <b69fa8dd68d816e7d24c88d3eda776ceb28c5dc5.1685890571.git.christophe.jaillet@wanadoo.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the probe, some resources are allocated with
dwc3_qcom_of_register_core() or dwc3_qcom_acpi_register_core(). The
corresponding resources are already coorectly freed in the error handling
path of the probe, but not in the remove function.
Fix it.
Fixes: 2bc02355f8 ("usb: dwc3: qcom: Add support for booting with ACPI")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Message-ID: <c0215a84cdf18fb3514c81842783ec53cf149deb.1685891059.git.christophe.jaillet@wanadoo.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>