Coccinelle noticed:
drivers/rtc/rtc-cpcap.c:271:7-32: ERROR: Threaded IRQ with no
primary handler requested without IRQF_ONESHOT
drivers/rtc/rtc-cpcap.c:287:7-32: ERROR: Threaded IRQ with no
primary handler requested without IRQF_ONESHOT
Signed-off-by: Tian Tao <tiantao6@hisilicon.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/1605000947-32882-1-git-send-email-tiantao6@hisilicon.com
Enable wakeup in the hym8563 driver if the IRQ was successfully
requested or if wakeup-source is set in the devicetree.
As per the description of device_init_wakeup(), it should be enabled
for "devices that everyone expects to be wakeup sources". One would
expect this to be the case with a real-time clock.
Tested on rk3288-rock2-square, which has an IRQ configured for the
RTC. As a result, wakeup was enabled during driver initialisation.
Fixes: dcaf038493 ("rtc: add hym8563 rtc-driver")
Reported-by: kernelci.org bot <bot@kernelci.org>
Signed-off-by: Guillaume Tucker <guillaume.tucker@collabora.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/1ea023e2ba50a4dab6e39be93d7de3146af71a60.1604653374.git.guillaume.tucker@collabora.com
Here we could use the '!=' expression to fix the following coccicheck
warning:
./drivers/rtc/rtc-sc27xx.c:566:50-55: WARNING: conversion to bool not needed here
Reported-by: Tosk Robot <tencent_os_robot@tencent.com>
Signed-off-by: Kaixu Xia <kaixuxia@tencent.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/1604647854-876-1-git-send-email-kaixuxia@tencent.com
When clk_hw_register_fixed_rate_with_accuracy() fails,
clk_data should be freed. It's the same for the subsequent
two error paths, but we should also unregister the already
registered clocks in them.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20201020061226.6572-1-dinghao.liu@zju.edu.cn
These functions should return zero on success. Non-zero returns are
treated as error. On some paths, this doesn't matter but in
nvmem_cell_read() a non-zero return would be passed to ERR_PTR() and
lead to an Oops.
Fixes: d6c3029f32 ("rtc: pcf2127: add support for accessing internal static RAM")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20201022070451.GA2817669@mwanda
The obvious advantages are:
- The linker can drop the watchdog functions if CONFIG_WATCHDOG is off.
- All watchdog stuff grouped together with only a single function call
left in generic code.
- Watchdog register is only read when it is actually used.
- Less #ifdefery
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200924105256.18162-2-u.kleine-koenig@pengutronix.de
Subsystem:
- new generic DT properties: aux-voltage-chargeable, trickle-voltage-millivolt
New driver:
- Microcrystal RV-3032
Drivers:
- ds1307: use aux-voltage-chargeable
- r9701, rx8010: modernization of the driver
- rv3028: fix clock output, trickle resistor values, RAM configuration
registers
-----BEGIN PGP SIGNATURE-----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=o9I0
-----END PGP SIGNATURE-----
Merge tag 'rtc-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"A new driver this cycle is making the bulk of the changes and the
rx8010 driver has been rework to use the modern APIs.
Summary:
Subsystem:
- new generic DT properties: aux-voltage-chargeable,
trickle-voltage-millivolt
New driver:
- Microcrystal RV-3032
Drivers:
- ds1307: use aux-voltage-chargeable
- r9701, rx8010: modernization of the driver
- rv3028: fix clock output, trickle resistor values, RAM
configuration registers"
* tag 'rtc-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (50 commits)
rtc: r9701: set range
rtc: r9701: convert to devm_rtc_allocate_device
rtc: r9701: stop setting RWKCNT
rtc: r9701: remove useless memset
rtc: r9701: stop setting a default time
rtc: r9701: remove leftover comment
rtc: rv3032: Add a driver for Microcrystal RV-3032
dt-bindings: rtc: rv3032: add RV-3032 bindings
dt-bindings: rtc: add trickle-voltage-millivolt
rtc: rv3028: ensure ram configuration registers are saved
rtc: rv3028: factorize EERD bit handling
rtc: rv3028: fix trickle resistor values
rtc: rv3028: fix clock output support
rtc: mt6397: Remove unused member dev
rtc: rv8803: simplify the return expression of rv8803_nvram_write
rtc: meson: simplify the return expression of meson_vrtc_probe
rtc: rx8010: rename rx8010_init_client() to rx8010_init()
rtc: ds1307: enable rx8130's backup battery, make it chargeable optionally
rtc: ds1307: consider aux-voltage-chargeable
rtc: ds1307: store previous charge default per chip
...
tm_wday is never checked for validity and it is not read back in
r9701_get_datetime. Avoid setting it to stop tripping static checkers:
drivers/rtc/rtc-r9701.c:109 r9701_set_datetime()
error: undefined (user controlled) shift '1 << dt->tm_wday'
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20201015191135.471249-4-alexandre.belloni@bootlin.com
If RV3028_CTRL1_EERD is not set (this is the default), the RTC will refresh
the RAM configuration registers from the EEPROM at midnight. It is
necessary to save the RAM registers back to EEPROM after modifying them.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20201009153101.721149-4-alexandre.belloni@bootlin.com
rv3028_clkout_set_rate unconditionally sets RV3028_CLKOUT_CLKOE but
clk_set_rate may be called with the clock disabled. Ensure the clock is
kept disabled if it was not yet enabled.
Also, the actual rate was overwritten when enabling the clock, properly
write to the register only once.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20201009153101.721149-1-alexandre.belloni@bootlin.com
Removing the struct member "dev" in mt6397 RTC driver because it's not
initialized and the only usage is for one debugging message.
Also fixed a typo in the error message.
Signed-off-by: Fei Shao <fshao@chromium.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20201008093414.1911699-1-fshao@chromium.org
Since the switch to using regmap this function no longer takes the
I2C client struct as argument nor do we even interact with the client
anywhere other than when creating the regmap.
Rename it to a less misleading name: "rx8010_init()".
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200917114656.9036-1-brgl@bgdev.pl
The ds1307 charger infrastructure now allows to add a rx8130 charger
setup that..
- does not depend on trickle-resistor-ohms
- does not use DS13XX_TRICKLE_CHARGER_MAGIC trickle-charge select (TCS)
bits
- keeps previous no-charge behavior for device trees without
aux-voltage-chargeable
Make that happen.
Signed-off-by: Bastian Krause <bst@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200917183246.19446-9-bst@pengutronix.de
Prefer aux-voltage-chargeable over trickle-diode-disable and set diode
accordingly. This is then passed to the chip's appropriate charge setup
function.
Signed-off-by: Bastian Krause <bst@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200917183246.19446-8-bst@pengutronix.de
Some RTC's batteries and supercaps were charged by default until now.
In contrast other RTCs allow charging but the driver did not configure
them to do so until now. These must not be charged by default to stay
backwards compatible.
In order to do that, store the charge default per chip.
Signed-off-by: Bastian Krause <bst@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200917183246.19446-7-bst@pengutronix.de
Make trickle-resistor-ohms optional for charging setups that do not
require specifying ROUT bits (specifying the resistor value between Vcc
and Vbackup). In order to allow specifying that, introduce
requires_trickle_resistor per chip.
Signed-off-by: Bastian Krause <bst@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200917183246.19446-6-bst@pengutronix.de
DS13XX_TRICKLE_CHARGER_MAGIC sets the trickle-charge select (TCS) bits
(7..4). The datasheet of Maxim Integrated's DS1339 [1] for instance
reads:
"To prevent accidental enabling, only a pattern on 1010 enables the
trickle charger. All other patterns disable the trickle charger."
Since not all RTCs connected to a backup battery or supercap use these
bits DS13XX_TRICKLE_CHARGER_MAGIC should not get applied for all charger
setups unconditionally.
Epson's RX8130 is such an example: Instead of TCS bits "SMPTSEL1",
"SMPTSEL0", "CHGEN" and "INIEN" are expected as bit 7..4.
DS1339 and DS1340 are currently the only RTCs in the ds1307 driver that
apply DS13XX_TRICKLE_CHARGER_MAGIC to their setup register value. So
apply DS13XX_TRICKLE_CHARGER_MAGIC in do_trickle_setup_ds1339() which
is used by both RTCs.
[1] https://datasheets.maximintegrated.com/en/ds/DS1339-DS1339U.pdf
[2] https://support.epson.biz/td/api/doc_check.php?dl=app_RX8130CE
Signed-off-by: Bastian Krause <bst@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200917183246.19446-5-bst@pengutronix.de
Fix a bug when not specify interrupts property in dts
as follows,
rtc-pcf2127-i2c 1-0051: failed to request alarm irq
rtc-pcf2127-i2c: probe of 1-0051 failed with error -22
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200915073213.12779-1-biwen.li@oss.nxp.com
ds1685_rtc_begin_data_access() tried to access an extended register before
enabling access to it by switching to bank 1. Depending on content in NVRAM
this could lead to an endless loop. While at it fix also switch back to
bank 0 in ds1685_rtc_end_data_access().
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Joshua Kinard <kumba@gentoo.org>
Link: https://lore.kernel.org/r/20200910084124.138560-1-tsbogend@alpha.franken.de
The only usage of st_rtc_ops is to assign its address to the ops field
in the rtc_device struct. which is a const pointer. Make it const to
allow the compiler to put it in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200913122644.35515-1-rikard.falkeborn@gmail.com
We don't need to check the time range manually in set_time(), we can
use range_min and range_max exposed by struct rtc_device.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200914154601.32245-15-brgl@bgdev.pl
This driver requires SMBUS to work. We can relax this requirement if we
switch to using i2c regmap and let the regmap sub-system figure out how
to talk to the bus.
This also has the advantage of shrinking the code for register updates.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200914154601.32245-14-brgl@bgdev.pl
We should generally use probe_new instead of probe when registering i2c
drivers. Convert rx8010 to using it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200914154601.32245-13-brgl@bgdev.pl
Using the size of the variable is preferred over using the size of its
type when allocating memory. Convert the call to devm_kzalloc() in
probe().
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200914154601.32245-11-brgl@bgdev.pl
Simple 'dev' looks better then repeated &client->dev and has the added
benefit of avoiding unnecessary line breaks.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200914154601.32245-10-brgl@bgdev.pl
The 'err' local variable in rx8010_init_client() doesn't need to be
initialized.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200914154601.32245-9-brgl@bgdev.pl
The time buffer len is used directly in this driver. For readability
it's better to define it as the difference between the date register
offsets and use sizeof() whenever referencing it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200914154601.32245-8-brgl@bgdev.pl
All other functions in this driver use 'err' for integer return values.
Do the same in rx8010_set_time() for consistency.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200914154601.32245-7-brgl@bgdev.pl
The define values in this driver are close to their names and they are
separated by spaces. Use tabs instead and align all defines.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200914154601.32245-6-brgl@bgdev.pl
Move local variables of the same type into a single line for better
readability.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200914154601.32245-5-brgl@bgdev.pl
The way the driver is implemented is buggy for the (admittedly unlikely)
use case where there are two RTCs with one having an interrupt configured
and the second not. This is caused by the fact that we use a global
rtc_class_ops struct which we modify depending on whether the irq number
is present or not.
Fix it by using two const ops structs with and without alarm operations.
While at it: not being able to request a configured interrupt is an error
so don't ignore it and bail out of probe().
Fixes: ed13d89b08 ("rtc: Add Epson RX8010SJ RTC driver")
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200914154601.32245-2-brgl@bgdev.pl
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200830080937.14367-1-krzk@kernel.org
Original device id would conflict with crypto driver, change it.
Signed-off-by: Peng Ma <peng.ma@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200818063609.39859-1-ran.wang_1@nxp.com
Ensure the OSF flag is cleared on the DS1388 when the clock is set.
Fixes: df11b323b1 ("rtc: ds1307: handle oscillator failure flags for ds1388 variant")
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200818013543.4283-1-chris.packham@alliedtelesis.co.nz
Similar to the other variants the DS1388 has a bit to stop the
oscillator to reduce the power consumption from VBAT. Ensure that the
oscillator is enabled when the system is up.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200816235731.21071-1-chris.packham@alliedtelesis.co.nz
