The major and minor number saved in the product_info structure
were copied from the address instead of the data, causing an
inconsistency in the reported versions during firmware loading:
usb 4-1: firmware: requesting edgeport/down.fw
/usr/src/linux/drivers/usb/serial/io_edgeport.c: downloading firmware version (930) 1.16.4
[..]
/usr/src/linux/drivers/usb/serial/io_edgeport.c: edge_startup - time 3 4328191260
/usr/src/linux/drivers/usb/serial/io_edgeport.c: FirmwareMajorVersion 0.0.4
This can cause some confusion whether firmware loaded successfully
or not.
Cc: stable@kernel.org
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As reported by Flavio Leitner, there is no synchronization to protect
NIU's get_stats method from seeing a NULL pointer in either
np->rx_rings or np->tx_rings. In fact, as far as ->ndo_get_stats
is concerned, these values are set completely asynchronously.
Flavio attempted to fix this using a RW semaphore, which in fact
works most of the time. However, dev_get_stats() can be invoked
from non-sleepable contexts in some cases, so this fix doesn't
work in all cases.
So instead, control the visibility of the np->{rx,tx}_ring pointers
when the device is being brough up, and use properties of the device
down sequence to our advantage.
In niu_get_stats(), return immediately if netif_running() is false.
The device shutdown sequence first marks the device as not running (by
clearing the __LINK_STATE_START bit), then it performans a
synchronize_rcu() (in dev_deactive_many()), and then finally it
invokes the driver ->ndo_stop() method.
This guarentees that all invocations of niu_get_stats() either see
netif_running() as false, or they see the channel pointers before
->ndo_stop() clears them out.
If netif_running() is true, protect against startup races by loading
the np->{rx,tx}_rings pointer into a local variable, and punting if
it is NULL. Use ACCESS_ONCE to prevent the compiler from reloading
the pointer on us.
Also, during open, control the order in which the pointers and the
ring counts become visible globally using SMP write memory barriers.
We make sure the np->num_{rx,tx}_rings value is stable and visible
before np->{rx,tx}_rings is.
Such visibility control is not necessary on the niu_free_channels()
side because of the RCU sequencing that happens during device down as
described above. We are always guarenteed that all niu_get_stats
calls are finished, or will see netif_running() false, by the time
->ndo_stop is invoked.
Reported-by: Flavio Leitner <fleitner@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We previously used a static array, but some new systems
had more states then we had array space, so dynamically
allocate space based on the number of states in the vbios.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=33851
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
The accelerate mode bit gets checked by certain atom
command tables to set up some register state. It needs
to be clear when setting modes and set when not.
Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=26942
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Some BIOSs (eg. the AMI BIOS on the Asus P4P800 motherboard) don't
initialise the GART address, and pcibios_assign_resources() can ignore it
because it can be marked as a host bridge (see
https://bugzilla.kernel.org/show_bug.cgi?id=24392#c5 for details). This
was handled correctly up to 2.6.35, but the pci_enable_device() cleanup in
2.6.36 96576a9e1a ("agp: intel-agp: do not use PCI resources before
pci_enable_device()") means that the kernel tries to enable the GART
before assigning it an address; in such cases the GART overlaps with other
device assignments and ends up being disabled.
This patch fixes https://bugzilla.kernel.org/show_bug.cgi?id=24392
Note that I imagine efficeon-agp.c probably has the same problem, but
I can't test that and I'd like to make sure this patch is suitable for
-stable (since 2.6.36 and 2.6.37 are affected).
Signed-off-by: Stephen Kitt <steve@sk2.org>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Maciej Rutecki <maciej.rutecki@gmail.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Kulikov Vasiliy <segooon@gmail.com>
Cc: Florian Mickler <florian@mickler.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This reverts commit f191f14407.
The AMD 751 and 761 chipsets are used on the UP1000, UP1100, and UP1500
OEM motherboards, but they neglect to do anything to make AGP work.
According to Ivan Kokshaysky:
There is quite fundamental conflict between the Alpha architecture and
x86 AGP implementation - Alpha is entirely cache coherent by design,
while x86 AGP is not (I mean native AGP DMA transactions, not a PCI over
AGP). There are no such things as non-cacheable mappings or software
support for cache flushing/invalidation on Alpha, so x86 AGP code won't
work on Nautilus.
So there's no point in allowing this driver to be configured on Alpha.
Signed-off-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
amd-k7-agp can't be built on Alpha anymore, so remove now unnecessary
code.
Signed-off-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
These should be handled by the clear_state setup, but set them
directly as well just to be sure.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Adds new packet to disable DX9 constant emulation.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
The RX lock is used to protect the RX buffer from concurrent access in DMA
mode between the timer and RX interrupt routines. It is independent from
the uart lock which is used to protect the TX buffer. It is possible for
a uart TX transfer to be started up from the RX interrupt handler if low
latency is enabled. So we need to split the locks to avoid deadlocking in
this situation.
In PIO mode, the RX lock is not necessary because the handle_simple_irq
and handle_level_irq functions ensure driver interrupt handlers are called
once on one core.
And now that the RX path has its own lock, the TX interrupt has nothing to
do with the RX path, so disabling it at the same time.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit 0587102cf9 replaced a direct
implementation of SIOCGICOUNT with an implementation of
tty_operations::get_icount, but it did not actually set
rs_360_ops.get_icount.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: stable@kernel.org [2.6.37]
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This field is settable but did not get copied.
Signed-off-by: Ken Mills <ken.k.mills@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit 728674a7e4 moved virtio_console.c
to drivers/tty/hvc/ under the perception of this being an hvc driver.
It was such once, but these days it has generic communication
capabilities as well, so move it to drivers/char/.
In the future, the hvc part from this file can be split off and moved
under drivers/tty/hvc/.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
CC: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] libsas: fix runaway error handler problem
[SCSI] fix incorrect value of SCSI_MAX_SG_CHAIN_SEGMENTS due to include file ordering
[SCSI] arcmsr: Fix the issue of system hangup after commands timeout on ARC-1200
[SCSI] mpt2sas: fix Integrated Raid unsynced on shutdown problem
[SCSI] mpt2sas: Kernel Panic during Large Topology discovery
[SCSI] mpt2sas: Fix the race between broadcast asyn event and scsi command completion
[SCSI] mpt2sas: Correct resizing calculation for max_queue_depth
[SCSI] mpt2sas: fix internal device reset for older firmware prior to MPI Rev K
[SCSI] mpt2sas: Fix device removal handshake for zoned devices
Some rtc drivers use the ioctl method instead of the alarm_irq_enable
method for enabling alarm interupts. With the new virtualized RTC
rework, its important for drivers to use the alarm_irq_enable instead.
This patch converts the drivers that use the AIE ioctl method to
use the alarm_irq_enable method. Other ioctl cmds are left untouched.
I have not been able to test or even compile most of these drivers.
Any help to make sure this change is correct would be appreciated!
CC: Alessandro Zummo <a.zummo@towertech.it>
CC: Thomas Gleixner <tglx@linutronix.de>
CC: Marcelo Roberto Jimenez <mroberto@cpti.cetuc.puc-rio.br>
Reported-by: Marcelo Roberto Jimenez <mroberto@cpti.cetuc.puc-rio.br>
Tested-by: Marcelo Roberto Jimenez <mroberto@cpti.cetuc.puc-rio.br>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Some RTC drivers enable functionality directly via their ioctl method
instead of using the generic ioctl handling code. With the recent
virtualization of the RTC layer, its now important that the generic
layer always be used.
This patch moved the rtc driver ioctl method call to after the generic
ioctl processing is done. This allows hardware specific features or
ioctls to still function, while relying on the generic code for handling
everything else.
This patch on its own may more obviously break rtc drivers that
implement the alarm irq enablement via their ioctl method instead of
implementing the alarm_irq_eanble method. Those drivers will be fixed
in a following patch. Additionaly, those drivers are already likely to
not be functioning reliably without this patch.
CC: Alessandro Zummo <a.zummo@towertech.it>
CC: Marcelo Roberto Jimenez <mroberto@cpti.cetuc.puc-rio.br>
CC: Thomas Gleixner <tglx@linutronix.de>
Reported-by: Marcelo Roberto Jimenez <mroberto@cpti.cetuc.puc-rio.br>
Tested-by: Marcelo Roberto Jimenez <mroberto@cpti.cetuc.puc-rio.br>
Signed-off-by: John Stultz <john.stultz@linaro.org>
This patch prevents a user space program from calling the RTC_IRQP_SET
ioctl with a negative value of frequency. Also, if this call is make
with a zero value of frequency, there would be a division by zero in the
kernel code.
[jstultz: Also initialize irq_freq to 1 to catch other divbyzero issues]
CC: Alessandro Zummo <a.zummo@towertech.it>
CC: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marcelo Roberto Jimenez <mroberto@cpti.cetuc.puc-rio.br>
Signed-off-by: John Stultz <john.stultz@linaro.org>
In drivers/net/wireless/wl1251/main.c:wl1251_op_bss_info_changed() we make
a call to ieee80211_beacon_get() which may return NULL, but we do not
check the return value before dereferencing the pointer.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
RDMA: Update missed conversion of flush_scheduled_work()
RDMA/ucma: Copy iWARP route information on queries
RDMA/amso1100: Fix compile warnings
RDMA/cxgb4: Set the correct device physical function for iWARP connections
RDMA/cxgb4: Limit MAXBURST EQ context field to 256B
IB/qib: Hold link for TX SERDES settings
mlx4_core: Add ConnectX-3 device IDs
This reverts commit 5fdbe44d03.
Apparently there exist userspace programs that expect to be able to
"loop back" and distribute to readers events written into
/dev/input/eventX and this change made for the benefit of SysRq
handler broke them. Now that SysRq uses alternative method to suppress
filtering of the events it re-injects we can safely revert this change.
Reported-by: Kristen Carlson Accardi <kristen@linux.intel.com>
Cc: stable@kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Internally 'disable' the filter when re-injecting Alt-SysRq instead
of relying on input core to suppress delivery of injected events
to the originating handler.
This allows to revert commit 5fdbe44d03
which causes problems with existing userspace programs trying to
loopback the events via evdev.
Reported-by: Kristen Carlson Accardi <kristen@linux.intel.com>
Cc: stable@kernel.org
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
When rebinding a serio driver via sysfs drvctl interface it is
possible for an interrupt to trigger after the disconnect of the
existing driver and before the binding of the new driver. This will
cause the serio interrupt handler to queue a rescan event which will
disconnect the new driver immediately after it is attached.
This change removes pending rescans from the serio event queue after
processing the drvctl request but before releasing the serio mutex.
Reproduction involves issuing a rebind of device port from psmouse
driver to serio_raw driver while generating input to trigger
interrupts. Then checking to see if the corresponding
i8042/serio4/driver is correctly attached to the serio_raw driver
instead of psmouse.
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
IORESOURCE_IRQ_* is wrong for irq_request, use the correct IRQF_* instead.
Signed-off-by: Alexander Stein <alexander.stein@informatik.tu-chemnitz.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'media_fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
[media] fix saa7111 non-detection
[media] rc/streamzap: fix reporting response times
[media] mceusb: really fix remaining keybounce issues
[media] rc: use time unit conversion macros correctly
[media] rc/ir-lirc-codec: add back debug spew
[media] ir-kbd-i2c: improve remote behavior with z8 behind usb
[media] lirc_zilog: z8 on usb doesn't like back-to-back i2c_master_send
[media] hdpvr: fix up i2c device registration
[media] rc/mce: add mappings for missing keys
[media] gspca - zc3xx: Discard the partial frames
[media] gspca - zc3xx: Fix bad images with the sensor hv7131r
[media] gspca - zc3xx: Bad delay when given by a table
Solved a locking issue that resulted in driver crashes with the 43224 and 43225
chips. The problem has been reported on several fora. Root cause was two fold:
hardware was being manipulated by two unsynchronized threads, and a scan
operation could interfere with an ongoing dynamic calibration process. Fix was
to invoke a lock on wl_ops_config() operation and to set internal flags when a
scan operation is started and stopped.
Please add this to the staging-linus branch.
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Roland Vossen <rvossen@broadcom.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
currently capture through dmic captures only silence
This patch configurs the dmic registers to capture properly
Signed-off-by: Harsha Priya <priya.harsha@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The hv_netvsc gets RNDIS_STATUS_MEDIA_CONNECT event after the VM
is live migrated. Adding call to netif_notify_peers() for this event
to send GARP (Gratuitous ARP) to notify network peers. Otherwise,
the VM's network connection may stop after a live migration.
This patch should also be applied to stable kernel 2.6.32 and later.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Hank Janssen <hjanssen@microsoft.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit 8f574b35f2 ("atl1c: Add AR8151 v2
support and change L0s/L1 routine") added support for a new adapter
but failed to add it to the PCI device table.
Signed-Off-By: Chuck Ebbert <cebbert@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This error was reported by cppcheck:
drivers/s390/net/smsgiucv.c:63: error: Using sizeof for array given as
function argument returns the size of pointer.
Although there is no runtime problem as long as sizeof(u8 *) == 8,
this misleading code should get fixed.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This error was reported by cppcheck:
drivers/s390/net/netiucv.c:568: error: Using sizeof for array given
as function argument returns the size of pointer.
sizeof(ipuser) did not result in 16 (as many programmers would have
expected) but sizeof(u8 *), so it is 4 or 8, too small here.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For OSA the CHPARM-definition determines the number of available
outbound queues.
A CHPARM-change may occur while a Linux system with probed
OSA device is in suspend state. This patch enables proper
resuming of an OSA device in this case.
Signed-off-by: Ursula braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For HiperSockets the framesize-definition determines the selected
mtu-size and the size of the allocated qdio buffers.
A framesize-change may occur while a Linux system with probed
HiperSockets device is in suspend state. This patch enables proper
resuming of a HiperSockets device in this case.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HiperSockets and OSA hardware report a maximum MTU size. Add checking
to reject larger MTUs than allowed by hardware.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setting of a MAC-address may fail because an already used MAC-address
is to bet set or because of authorization problems. In those cases
qeth issues a message, but the mentioned MAC-address is not the
new MAC-address to be set, but the actual MAC-address. This patch
chooses now the new MAC-address to be set for the error messages.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
6250 2x2 devices have 2 tx chain and 2 rx chain. For some reason,
the EEPROM contain incorrect information and indicate it only has single
tx chain. overwrite it with .cfg parameter to make sure both chain 'A' and
chain 'B' can be used for transmit and receive
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Based on the vbios code. This should hopefully
fix the pll problems on a number of avivo asics
once it's enabled.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Some fixes to the thermal sensor code:
- handle negative numbers
- properly handle temp calculation on different asics
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'intel/drm-intel-fixes' of /ssd/git/drm-next:
drm/i915: Only bind to function 0 of the PCI device
drm/i915: Suppress spurious vblank interrupts
drm: Avoid leak of adjusted mode along quick set_mode paths
drm: Simplify and defend later checks when disabling a crtc
drm: Don't switch fb when disabling an output
drm/i915: Reset crtc after resume
drm/i915/crt: Force the initial probe after reset
drm/i915: Reset state after a GPU reset or resume
drm: Add an interface to reset the device
drm/i915/sdvo: If at first we don't succeed in reading the response, wait
Activating a spare in an array while resync/recovery is already
happening can lead the that spare being marked in-sync when it isn't
really.
So don't allow the 'slot' to be set (this activating the device)
while resync/recovery is happening.
Signed-off-by: NeilBrown <neilb@suse.de>
Accidently busted a while back. We'll be creating objects that aren't
necessary here, but, they're never used so no harm..
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
I broke this with my commit
07cfe0e7a8
This fixes fdo #33434
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
It is illegal to call netif_stop_queue before register_netdev.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While running insmod/rmood in a loop, an unnecessary netif_stop_queue
causes the system to crash. Remove the netif_stop_queue call
and netif_start_queue in the link status update path.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The comments under "config STUB_POULSBO" are close to correct,
but they are not being followed. This patch updates them to reflect
the requirements for THERMAL.
This build error is caused by STUB_POULSBO selecting ACPI_VIDEO
when ACPI_VIDEO's config requirements are not met.
ERROR: "thermal_cooling_device_register" [drivers/acpi/video.ko] undefined!
ERROR: "thermal_cooling_device_unregister" [drivers/acpi/video.ko] undefined!
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This warning was reported by cppcheck:
drivers/isdn/icn/icn.c:1641: error: Dangerous usage of 'rev' (strncpy doesn't always 0-terminate it)
If strncpy copied 20 bytes, the destination string rev was not terminated.
The patch adds one more byte to rev and makes sure that this byte is
always 0.
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Tejun Heo <tj@kernel.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The chip was erroneously configured to accept all multicast frames
in a normal (none-promisc) rx mode both on the RSS and on the FCoE L2 rings
when in an NPAR mode. This caused packet duplication for every received multicast
frame in this mode.
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Early chipsets (gen2/3) used function 1 as a placeholder for multi-head.
We used to ignore these since they were not assigned to
PCI_CLASS_DISPLAY_VGA. However with 934f992c7 we attempt to bind to all
Intel PCI_CLASS_DISPLAY devices (and functions) to work in multi-gpu
systems. This fails hard on gen2/3.
Reported-by: Ferenc Wágner <wferi@niif.hu>
Tested-by: Ferenc Wágner <wferi@niif.hu>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=28012
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
This error is reported by cppcheck:
drivers/net/vxge/vxge-config.c:3693: warning: Mutual exclusion over || always evaluates to true. Did you intend to use && instead?
It looks like cppcheck is correct, so fix this. No test was run.
Cc: Ramkrishna Vepa <ramkrishna.vepa@exar.com>
Cc: Sivakumar Subramani <sivakumar.subramani@exar.com>
Cc: Sreenivasa Honnur <sreenivasa.honnur@exar.com>
Cc: Jon Mason <jon.mason@exar.com>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Acked-by: Ram Vepa <ram.vepa@exar.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
free the skb's when the Tx of PAPRD frames fails and also add a debug
message indicating that.
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When built with rcu checks enabled, vhost triggers
bogus warnings as vhost features are read without
dev->mutex sometimes, and private pointer is read
with our kind of rcu where work serves as a
read side critical section.
Fixing it properly is not trivial.
Disable the warnings by stubbing out the checks for now.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
There are a few error paths in ehci_hcd_omap_probe that can be triggered
because of memory allocation or hw failure. Change those dev_dbg error
prints to dev_err with an error code printed so that the end users are able
to notice the issue.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Gadget MUSB driver handles dma mappings in musb_gadget_queue(). Where as it is
possible for dma code to reject the usb request later at ->channel_program()
called from txstate()/rxstate()
For example ->channel_program in tusb6010_omap.c:
static int tusb_omap_dma_program(struct dma_channel *channel, u16 packet_sz,
u8 rndis_mode, dma_addr_t dma_addr, u32 len)
{
...
if (unlikely(dma_addr & 0x1) || (len < 32) || (len > packet_sz))
return false;
...
if (dma_addr & 0x2)
return false;
...
}
In this case, usb request will be handled in PIO mode which renders dma mapping
operations unnecessary.
This patch adds an api to allow dma code to indicate incompatibility with usb
request. Gadget musb driver call this api, if available, before dma mappings to
avoid any unnecessary mapping operations.
Signed-off-by: Mian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If dma buffers are mapped by a higher layer, with a boolean musb_request.mapped
it is still possible to call dma_sync_single_for_device() from
musb_g_giveback(), even if txstate()/rxstate() has called unmap_dma_buffer()
before falling back to pio mode.
Moreover, check for musb_ep->dma is moved within map_dma_buffer() so where
applicable checks for it are removed. And where possible, checks for
is_dma_capable() are merged with buffer map state check.
Signed-off-by: Mian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We know that blackfin doesn't support double
buffering feature as of today. So we add a
flag set by musb_platform_init() to forcefully
disable that feature.
Such flag is created and marked as deprecated
to force us to find a solution for the missing
double buffering support on blackfin.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Blackfin platform doesn't support 32bits musbdma registers, so change back to
use musb_read/writew instead of musb_read/writel and simply some format casts.
Signed-off-by: Bob Liu <lliubbo@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
musb_probe() only regards 0 as a wrong IRQ number, despite platform_get_irq()
that it calls returns -ENXIO in that case. It leads to musb_init_controller()
calling request_irq() with a negative IRQ number, and when it naturally
fails, the following is printed to the console:
request_irq -6 failed!
musb_init_controller failed with status -19
Fix musb_probe() to filter out the error values as well as 0.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch fixes kernel panic during s2ram, which is caused
by the below:
- musb is not put into drv data of musb platform device if
CONFIG_USB_MUSB_HDRC_HCD is defined
- glue layer driver always get musb instance via platform_get_drvdata.
The patch fixes the issue by always puting musb into drv data
of musb platform device, which is doable even the platform device
is a host controller device.
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Sergei Shtylyov <sshtylyov@mvista.com>
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Serial devices send both pen and touch data through the same logical
port. Since we scaled touch to pen maximum, we use pen resolution
for touch as well here.
This is under the assumption that pen and touch share the same physical
surface. In the case when a small physical dimensional difference occurs
between pen and touch, we assume the tolerance for touch point precision
is higher than pen and the difference is within touch point tolerance.
A per-MT tool based resolution mechanism should be introduced if the
above assumption does not hold true for the pen and touch devices any
more.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This error was reported by cppcheck:
drivers/net/enc28j60.c:815: error: Using sizeof for array given as function argument returns the size of pointer.
The original code reads 4 or 8 bytes instead of TSV_SIZE (= 100) bytes.
I just fixed the code, but did not run any tests.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
axnet_cs:
mdelay of 10ms is too long at ei_rx_overrun.
It should be reduced to 2ms.
Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'usb-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (42 commits)
usb: gadget: composite: avoid access beyond array max length
USB: serial: handle Data Carrier Detect changes
USB: gadget: Fix endpoint representation in ci13xxx_udc
USB: gadget: Fix error path in ci13xxx_udc gadget probe function
usb: pch_udc: Fix the worning log issue at gadget driver remove
USB: serial: Updated support for ICOM devices
USB: ehci-mxc: add work-around for efika mx/sb bug
USB: unbreak ehci-mxc on otg port of i.MX27
drivers: update to pl2303 usb-serial to support Motorola cables
USB: adding USB support for Cinterion's HC2x, EU3 and PH8 products
USB serial: add missing .usb_driver field in serial drivers
USB: ehci-fsl: Fix 'have_sysif_regs' detection
USB: g_printer: fix bug in module parameter definitions
USB: g_printer: fix bug in unregistration
USB: uss720: remove duplicate USB device
MAINTAINERS: add ueagle-atm entry
USB: EHCI: fix DMA deallocation bug
USB: pch_udc: support new device ML7213 IOH
usb: pch_udc: Fixed issue which does not work with g_serial
usb: set ep_dev async suspend should be later than device_initialize
...
* 'staging-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6: (26 commits)
staging: r8712u: Add new device IDs
staging: brcm80211: fix suspend/resume issue in brcmsmac
staging: brcm80211: remove assert to avoid panic since 2.6.37 kernel
Staging: iio: Aditional fixpoint formatted output bugfix
staging: usbip: vhci: use urb->dev->portnum to find port
staging: usbip: vhci: handle EAGAIN from SO_RCVTIMEO
staging: usbip: vhci: friendly log messages for connection errors
staging: usbip: vhci: refuse to enqueue for dead connections
staging: usbip: vhci: give back URBs from in-flight unlink requests
staging: usbip: vhci: update reference count for usb_device
staging: usbip: stub: update refcounts for devices and interfaces
staging: tidspbridge: replace mbox callback with notifier_call
staging: comedi: ni_labpc: Use shared IRQ for PCMCIA card
Staging: speakup: &&/|| confusion in silent_store()
iio: Fixpoint formatted output bugfix
staging: rt2860: Fix incorrect netif_stop_queue usage warning
staging: r8712u: Fix memory leak in firmware loading
staging: tidspbridge: configure full L1 MMU range
staging: rt2870sta: Add ID for Linksys WUSB100v2
Staging: xgfib: put parenthesis in the right place
...
* 'tty-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
tty/serial: fix apbuart build
n_hdlc: fix read and write locking
serial: unbreak billionton CF card
tty: use for_each_console() and WARN() on sysfs failures
vt: fix issue when fbcon wants to takeover a second time.
Fix up trivial conflict in drivers/tty/tty_io.c
Without this dependency the softing driver will be buildable on s390,
where it fails.
Signed-Off-By: Chuck Ebbert <cebbert@redhat.com>
Acked-by: Kurt Van Dijck <kurt.van.dijck@eia.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
When DEBUG_SPI is included in the debug log level wl1271_spi_reset()
will dump the already freed memory instead of the SPI buffer.
This bug was spotted by the semantic patch tool coccinelle using the
script found at scripts/coccinelle/free/kfree.cocci.
More information about semantic patching is available at
http://coccinelle.lip6.fr/
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
One saa7111 device is reporting a different ID:
saa7115 0-0024: chip found @ 0x48 (ID 0f7111d0e111111) does not match a known saa711x chip.
As this is for sure a saa7111, change the detection code to also
cover this device.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The streamzap driver has relatively low sampling resolution, and any
delays in reporting events seem to cause some minor problems for the
likes of irw when using the lirc bridge driver, resulting in a single
keypress registering as multiple independent ones, rather than as a
single press with repeats. If we call ir_raw_event_handle() more
frequently and reset the rawir kfifo at end-of-signal, the behavior
improves quite a bit.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make sure rawir struct is zeroed out before populating it for each
ir_raw_event_store_with_filter() call, and when we see a trailing 0x80
packet (end-of-data), issue an ir_raw_event_reset() call.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Due to my own stupidity, some of the wrong time unit conversion macros
were being used inside some of the IR drivers I've been working on. Fix
that, and convert over some additional places to also use the macros.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some occasionally useful debug spew disappeared as part of a feature
update a while back, and I'm finding myself in need of it again to help
diagnose some issues.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add the same "are you ready?" i2c_master_send() poll command to
get_key_haup_xvr found in lirc_zilog, which is apparently seen in
the Windows driver for the PVR-150 w/a z8. This stabilizes what is
received from both the HD-PVR and HVR-1950, even with their polling
intervals at the default of 100, thus the removal of the custom
260ms polling_interval in pvrusb2-i2c-core.c.
Acked-by: Andy Walls <awalls@md.metrocast.net>
Acked-by: Mike Isely <isely@isely.net>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Both the HD-PVR and HVR-1950, driven by the hdpvr and pvrusb2 drivers
respectively, have a zilog z8 chip exposed via i2c. These are both
usb-connected devices, and on both of them, back-to-back i2c_master_send
calls that work fine with a z8 on a pci card fail with a -EIO, as the
chip isn't yet ready from the prior command. To cope with that, add a
delay and retry loop where necessary.
Acked-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We have to actually call i2c_new_device() once for each of the rx and tx
addresses. Also improve error-handling and device remove i2c cleanup.
Reviewed-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Per http://mediacenterguides.com/book/export/html/31 and investigation
by Erin, we were missing these last three mappings to complete the mce
key table. Lets remedy that.
Reported-by: Erin Simonds <fisslefink@gmail.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In some cases, some frames may not end with the JPEG end of frame.
Being not complete, they are now discarded.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The problem was introduced by the commit 2af0b4c60c.
Some registers were no more initialized.
Tested-by: <Giovanni Scafora giovanni@archlinux.org>
Tested-by: <Sergey Manucharian sm@ingeniware.com>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hugh Dickins found that characters in xterm were going missing and oft
delayed. Being the curious type, he managed to associate this with the
new high-precision vblank patches; disabling these he found, restored
the orderliness of his characters.
The oddness begins when one realised that Hugh was not using vblanks at
all on his system (fvwm and some xterms). Instead, all he had to go on
were warning of a pipe underrun, curiously enough at around 60Hz. He
poked and found that in addition to the underrun warning, the hardware
was flagging the start of a new frame, a vblank, which in turn was
kicking off the pending vblank processing code.
There is little we can do for the underruns on Hugh's machine, a
Crestline [965GM], which must have its FIFO watermarks set to 8.
However, we do not need to process the vblank if we know that they are
disabled...
Reported-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
By setting the FB of a CRTC to NULL, we are turning off the CRTC (and so
disable the unused encoders and connectors). As such we can simplify the
later tests by making sure the set->mode is NULL. Setting the
num_connectors to zero means that we do not need to loop over the unused
connectors.
All current usage appears correct, this only builds additional defense
into the routine.
References: https://bugzilla.kernel.org/show_bug.cgi?id=27722
Tested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
In drm_crtc_helper_set_config, we call drm_crtc_helper_set_mode which
may return early and do no operation if the crtc is to be disabled. In
this case we merrily swap to the new fb, discarding the old_fb believing
that it has been cleaned up. However, due to the early return, the
old_fb was not presented to the backend for correct reaping, and nor was
the new one - which is about to be reaped via the
drm_helper_disable_unused_functions(), leading to incorrect refcounting
of the pinned objects.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=27722
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=29857
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=29230
Tested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
As per the reference manual, bit "L" should be set while bit "C"
should be cleared for the last buffer descriptor in the non-cyclic
chain, so that sdma can stop trying to find the next BD and end
the transfer.
In case of sdma_prep_slave_sg(), BD_LAST needs to be set and BD_CONT
be cleared for the last BD.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
sdma_handle_channel_loop() is the handler of cyclic tx. One period
success does not really mean the success of the tx. Instead of
DMA_SUCCESS, DMA_IN_PROGRESS should be the one to tell.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The sdmac->status was designed to reflect the status of the tx,
so simply return it in sdma_tx_status(). Then dma client can call
dma_async_is_tx_complete() to know the status of the tx.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
sdma_prep_dma_cyclic() sets sdmac->status to DMA_ERROR in err_out,
and sdma_prep_slave_sg() needs to do the same. Otherwise,
sdmac->status stays at DMA_IN_PROGRESS, which will make the function
return immediately next time it gets called.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This is a leftover from the time that the driver did not have
sdma_prep_dma_cyclic callback and implemented sound dma as a looped
sg chain. And it can be removed now.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
We need channel 0 of the sdma engine for internal purposes. We
accomplished this by calling dma_request_channel() in the probe
function. This does not work when multiple dma engines are
present which is the case when IPU support for i.MX31/35 is
compiled in. So instead of registering channel 0 and reserving
it afterwards simply do not register it in the first place.
With this the dmaengine channel counting does not match sdma
channel counting anymore, so we have to use sdma channel counting
in the driver.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch lets sdma_prep_slave_sg fail if the entries of an
sg list do not start on multiples of the word size or if the
lengths are not multiple of the word size.
Also, catch the previously unhandled DMA_SLAVE_BUSWIDTH_8_BYTES
and DMA_SLAVE_BUSWIDTH_UNDEFINED cases.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
We should not report incomplete blocks on error. Return the number of
bytes successfully transferred, rounded down to the nearest block.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When we encounter an error, make sure we complete the transaction
otherwise we'll leave the request dangling.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Prevent the following compiler warning if compiling a 31 bit kernel:
drivers/s390/cio/qdio_main.c: In function ‘get_outbound_buffer_frontier’:
drivers/s390/cio/qdio_main.c:646:16: warning: ‘state’ may be used uninitialized in this function
CC lib/radix-tree.o
CC drivers/s390/scsi/zfcp_cfdc.o
drivers/s390/cio/qdio_main.c: In function ‘qdio_inbound_q_moved’:
drivers/s390/cio/qdio_main.c:479:16: warning: ‘state’ may be used uninitialized in this function
drivers/s390/cio/qdio_main.c:479:16: note: ‘state’ was declared here
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If a device is not resumed correctly the system crashes when this
device is set offline. This may happen if it gets disconnected
during suspend.
Check if the device is already removed from alias handling and skip
these steps to prevent the kernel panic.
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Update bnx2x version to 1.62.00-5
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All functions on a port should be set to take the MDC/MDIO lock to avoid contention on the bus
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix link on BCM57712 + BCM8073 when port swap is enabled. Common PHY reset was done on the wrong port.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix blink rate of activity LED of the BCM84823 on 10G link
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A rare link issue with the BCM8073 PHY may occur due to setting XAUI low power mode, while the PHY microcode already does that.
The fix is not to set set XAUI low power mode for this PHY.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a transfer is initiated from memory to a peripheral, then data is
fetched and the channel is marked busy. This busy status persists until
the HALT bit is set and the queued data has been transfered to the
peripheral. Waiting indefinitely after setting the HALT bit results in
system lockups. Timeout this operation, and print an error when this
happens.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
If we try to pause a channel when terminating a transfer, we could end
up spinning for it to become inactive indefinitely, and can result in
an uninterruptible wait requiring a reset to recover from.
Terminating a transfer is supposed to take effect immediately, but may
result in data loss.
To make this clear, rename the function to pl08x_terminate_phy_chan().
Also, make sure it is always consistently called - with the spinlock
held and IRQs disabled, and ensure that the TC and ERR interrupt status
is always cleared.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
There is no need to set this to zero at this point. It will be
set to zero by remove_and_add_spares or at the start of
md_do_sync at the latest.
And setting it to zero before MD_RECOVERY_RUNNING is cleared can
make a 'zero' appear briefly in the 'sync_completed' sysfs attribute
just as resync is finishing.
So simply remove this setting to zero.
Signed-off-by: NeilBrown <neilb@suse.de>
Do not respond with -EINVAL to EVIOCGKEYCODE for not-yet-mapped
scancodes, but rather return KEY_RESERVED.
This fixes breakage with Ubuntu's input-kbd utility that stopped
returning full keymaps for remote controls.
Tested-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tested-by: Mark Lord <kernel@teksavvy.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
libata: set queue DMA alignment to sector size for ATAPI too
libata: DVR-212D can't do SETXFER DVD-RW DVR-212D
ahci: add HFLAG_YES_FBS and apply it to 88SE9128
pata_hpt37x: inherit prereset() method for HPT374
ahci: AHCI mode SATA patch for Intel DH89xxCC DeviceIDs
pata_hpt37x: fold 'if' statement into 'switch'
pata_hpt{37x|3x2n}: use pr_*(DRV_NAME ...) instead of printk(KERN_* ...)
pata_hpt{366|37x}: use pr_warning(...) instead of printk(KERN_WARNING ...)
pata_mpc52xx: inherit from ata_bmdma_port_ops
remove_and_add_spares is called in two places where the needs really
are very different.
remove_and_add_spares should not be called on an array which is about
to be reshaped as some extra devices might have been manually added
and that would remove them. However if the array is 'read-auto',
that will currently happen, which is bad.
So in the 'ro != 0' case don't call remove_and_add_spares but simply
remove the failed devices as the comment suggests is needed.
Signed-off-by: NeilBrown <neilb@suse.de>
This patch introduces raid 1 to raid0 takeover operation
in kernel space.
Signed-off-by: Krzysztof Wojcik <krzysztof.wojcik@intel.com>
Signed-off-by: Neil Brown <neilb@nbeee.brown>
This flag is not needed and is used badly.
Devices that are included in a native-metadata array are reserved
exclusively for that array - and currently have AllReserved set.
They all are bd_claimed for the rdev and so cannot be shared.
Devices that are included in external-metadata arrays can be shared
among multiple arrays - providing there is no overlap.
These are bd_claimed for md in general - not for a particular rdev.
When changing the amount of a device that is used in an array we need
to check for overlap. This currently includes a check on AllReserved
So even without overlap, sharing with an AllReserved device is not
allowed.
However the bd_claim usage already precludes sharing with these
devices, so the test on AllReserved is not needed. And in fact it is
wrong.
As this is the only use of AllReserved, simply remove all usage and
definition of AllReserved.
Signed-off-by: NeilBrown <neilb@suse.de>
As spares can be added manually before a reshape starts, we need to
find them all to mark some of them as in_sync.
Previously we would abort looking for spares when we found an
unallocated spare what could not be added to the array (implying there
was no room for new spares). However already-added spares could be
later in the list, so we need to keep searching.
Signed-off-by: NeilBrown <neilb@suse.de>
As spares can be added to the array before the reshape is started,
we need to find and count them when checking there are enough.
The array could have been degraded, so we need to check all devices,
no just those out side of the range of devices in the array before
the reshape.
So instead of checking the index, check the In_sync flag as that
reliably tells if the device is a spare or this purpose.
Signed-off-by: NeilBrown <neilb@suse.de>
There are two consecutive 'if' statements.
if (mddev->delta_disks >= 0)
....
if (mddev->delta_disks > 0)
The code in the second is equally valid if delta_disks == 0, and these
two statements are the only place that 'added_devices' is used.
So make them a single if statement, make added_devices a local
variable, and re-indent it all.
No functional change.
Signed-off-by: NeilBrown <neilb@suse.de>
If we try to update_raid_disks and it fails, we should put
'delta_disks' back to zero. This is important because some code,
such as slot_store, assumes that delta_disks has been validated.
Signed-off-by: NeilBrown <neilb@suse.de>
This error is reported by cppcheck:
drivers/gpu/drm/radeon/radeon_encoders.c:1066: warning: Mutual exclusion over || always evaluates to true. Did you intend to use && instead?
It looks like cppcheck is correct, so fix this. No test was run.
Cc: David Airlie <airlied@linux.ie>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fix the referenced project website to www.mictronics.de in the Kconfig
help text for the slcan driver.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Variable name sdma and sdmac are consistently used as the pointer to
sdma_engine and sdma_channel respectively throughout the file. The
patch fixes the inconsistency seen in function sdma_assign_cookie().
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
When loading the microcode to the SDMA engine we have to use
the ram_code_start_addr found in the firmware image. The copy
in the sdma engine is not initialized correctly. This is broken
since:
5b28aa3 dmaengine i.MX SDMA: Allow to run without firmware
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This reverts commit a121f64399.
Unfortunately, this commit breaks UBIFS backward compatibility and
makes new UBIFS refuse older UBIFS-formatted media:
UBIFS error: validate_sb: min. I/O unit mismatch: 8 in superblock, 64 real
Thus, we have to revert this patch and work on a better solution.
Reported-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
On some machines, like Dell Studio XPS 16 (1640), touchpad fails to
respond to the standard query after first reset but may start
responding later, so let's repeat reset sequence several (3) times.
Signed-off-by: Alexandre Peixoto Ferreira <alexandref75@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
synaptics_set_advanced_gesture_mode() affect capabilities bits we should
perform comparison after calling this function, otherwise they will never
match and we will be forced to perform full reconnect.
Signed-off-by: Alexandre Peixoto Ferreira <alexandref75@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Commit f06267104d ("RDMA: Update workqueue usage") introduced ib_wq
and removed the use of flush_scheduled_work(); however, during the merge
process one chunk was lost in ib_sa_remove_one(). Fix it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Roland Dreier <roland@purestorage.com>
For iWARP rdma_cm ids, the "route" information is the L2 src and
next hop addresses.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Fix compile warnings on 32-bit by using "0" instead of "(u64) NULL" to
assign to "c2_vq_req->reply_msg".
Signed-off-by: Ralf Thielow <ralf.thielow@googlemail.com>
[ Change from "(unsigned long) NULL" to plain old "0" as suggested by
Bart Van Assche <bvanassche@acm.org>. - Roland ]
Signed-off-by: Roland Dreier <roland@purestorage.com>
The PF passed to FW was 0, causing PCI failures in an SR-IOV environment.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Cc: <stable@kernel.org>
Signed-off-by: Roland Dreier <roland@purestorage.com>
MAXBURST cannot exceed 256B for on-chip queues. With a 512B MAXBURST,
we can lock up the chip.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Cc: <stable@kernel.org>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Hold the IB link at DISABLED until we get the correct TX settings
on mezz boards.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
While unloading the driver, the ps_usecount is incremented
before configuring gpio registers in deinit_device.
But it is failed to restore the ps_usecount after that.
The problem is that the chip is forcibly moved to FULL SLEEP
by radio_disable when mac80211 is reporting as idle
though ps_usecount is not zero.
This patch retores ps_usecount properly and ensures that
the chip is always moved to full sleep only if ps usage
count is zero which also helps in debugging deadbeef on
multivif case. And also fixes the following warning.
ath: DMA failed to stop in 10 ms AR_CR=0xdeadbeef AR_DIAG_SW=0xdeadbeef
ath: Could not stop RX, we could be confusing the DMA engine when we
start RX up
------------[ cut here ]------------
WARNING: at drivers/net/wireless/ath/ath9k/recv.c:536
ath_stoprecv+0xf4/0x100 [ath9k]()
Cc: stable@kernel.org
Cc: Paul Stewart <pstew@google.com>
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The bit 6 & 7 of AR_WA (0x4004) should be enabled only
for the chips that are supporting L0s functionality
while resuming back from S3/S4.
Enabling these bits for AR9280 is causing system hang
within a few S3/S4-resume cycles.
Cc: stable@kernel.org
Cc: Jack Lee <jlee@atheros.com>
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ata_pio_sectors() expects buffer for each sector to be contained in a
single page; otherwise, it ends up overrunning the first page. This
is achieved by setting queue DMA alignment. If sector_size is smaller
than PAGE_SIZE and all buffers are sector_size aligned, buffer for
each sector is always contained in a single page.
This wasn't applied to ATAPI devices but IDENTIFY_PACKET is executed
as ATA_PROT_PIO and thus uses ata_pio_sectors(). Newer versions of
udev issue IDENTIFY_PACKET with unaligned buffer triggering the
problem and causing oops.
This patch fixes the problem by setting sdev->sector_size to
ATA_SECT_SIZE on ATATPI devices and always setting DMA alignment to
sector_size. While at it, add a warning for the unlikely but still
possible scenario where sector_size is larger than PAGE_SIZE, in which
case the alignment wouldn't be enough.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: John Stanley <jpsinthemix@verizon.net>
Tested-by: John Stanley <jpsinthemix@verizon.net>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
PIONEER DVR-212D can't do SETXFER like its sibling DVRTD08. Add
ATA_HORKAGE_NOSETXFER for it. Reported in bko#27502.
https://bugzilla.kernel.org/show_bug.cgi?id=27502
Signed-off-by: Francesco Antonacci <fraanto@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Commit 5f173107ec added HFLAG_YES_FBS workaround for 88SE9128
(1b4b:9123).
However, that change inadvertently caused the legacy IDE interface of
the controller (with the same pci id) to become associated with the AHCI
driver as well, causing the driver to try to bring the interface up in
vain.
Fix that by matching against class as well.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Commit ab81a505ae (pata_hpt37x: unify ->pre_reset
methods) neglected to remove the initializer for the prereset() method from
'hpt374_fn1_port_ops' (it's inherited from 'hpt372_port_ops' anyway), as well
as to update the comment in hpt37x_init_one()...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch adds the AHCI-mode SATA DeviceID for the Intel DH89xxCC PCH.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
hpt37x_init_one() has a large *if* statement which should really be folded into
the *switch* statement that currently constitutes its *else* branch, reducing
one level of indentation...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
... the same as the 'pata_hpt366' driver does.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
pata_mpc52xx supports BMDMA but inherits ata_sff_port_ops which
triggers BUG_ON() when a DMA command is issued. Fix it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Roman Fietze <roman.fietze@telemotive.de>
Cc: Sergei Shtylyov <sshtylyov@mvista.com>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/nv50: fix regression on IGPs
drm/radeon/kms: re-emit full context state for evergreen blits
drm/radeon/kms: release CMASK access in preclose_kms
drm/radeon/kms: fix r6xx+ scanout on BE systems
drm/radeon/kms: clean up some magic numbers
drm/radeon/kms: only enable HDMI mode if radeon audio is enabled
radeon/kms: fix dp displayport mode validation
drm/nvc0/grctx: correct an off-by-one
drm/nv50: Fix race with PFIFO during PGRAPH context destruction.
drm/nouveau: Workaround incorrect DCB entry on a GeForce3 Ti 200.
drm/nvc0: implement irq handler for whatever's at 0x14xxxx
drm/nvc0: fix incorrect TPC register setup
drm/nouveau: probe for adt7473 before f75375
drm/nouveau: remove dead function definition
clear state doesn't seem to work properly in some cases
Fixes hangs in heavy 3D on some evergreen cards reported on
IRC.
May fix:
https://bugs.freedesktop.org/show_bug.cgi?id=33381
possibly others.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@gmail.com>
The Linux network stack expects all GSO SKBs to have ip_summed ==
CHECKSUM_PARTIAL (which implies that the frame contains a partial
checksum) and the Xen network ring protocol similarly expects an SKB
which has GSO set to also have NETRX_csum_blank (which also implies a
partial checksum).
However there have been cases of buggy guests which mark a frame as
GSO but do not set csum_blank. If we detect that we a receiving such a
frame (which manifests as ip_summed != PARTIAL && skb_is_gso) then
force the SKB to partial and recalculate the checksum, since we cannot
rely on the peer having done so if they have not set csum_blank.
Add an ethtool stat to track occurances of this event.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: David Miller <davem@davemloft.net>
Cc: xen-devel@lists.xensource.com
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
The MMCIDATACNT register contain the number of byte left at error
not the number of words, so loose the << 2 thing. Further if CRC
fails on the first block, we may end up with a negative number
of transferred bytes which is not good, and the formula was in
wrong order.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We do not kill any scheduled tasklets when stopping device, that may
cause usage of resources after free. Disable interrupts, kill tasklets
and then works in correct order.
Cc: stable@kernel.org
Tested-by: Sujith <m.sujith@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We do not kill any scheduled tasklets when stopping device, that may
cause usage of resources after free. Moreover we enable interrupts
in tasklet function, so we could potentially end with interrupts
enabled when driver is not ready to receive them.
I think patch should fix Ben's kernel crash from:
http://marc.info/?l=linux-wireless&m=129438358921501&w=2
Cc: stable@kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ath5k version of ieee80211_generic_frame_duration() returns
an __le16 for standard modes but a cpu-endian int for turbo/half/
quarter rates. Make it always return cpu-endian values.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Bruno Randolf <br1@einfach.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Review spotted a problem with the error handling in ath5k_hw_dma_stop:
a successful return from ath5k_hw_stop_tx_dma will be treated as
an error, so we always bail out of the loop after processing a single
active queue. As a result, we may not actually stop some queues during
reset.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Bruno Randolf <br1@einfach.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Reviewed-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the source code from Realtek was prepared for kernel inclusion,
some routines were refactored to reduce the level of indentation. This
patch repairs errors introduced in that process.
Signed-off-by: Chaoming Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (43 commits)
bnx2: Eliminate AER error messages on systems not supporting it
cnic: Fix big endian bug
xfrm6: Don't forget to propagate peer into ipsec route.
tg3: Use new VLAN code
bonding: update documentation - alternate configuration.
TCP: fix a bug that triggers large number of TCP RST by mistake
MAINTAINERS: remove Reinette Chatre as iwlwifi maintainer
rt2x00: add device id for windy31 usb device
mac80211: fix a crash in ieee80211_beacon_get_tim on change_interface
ipv6: Revert 'administrative down' address handling changes.
textsearch: doc - fix spelling in lib/textsearch.c.
USB NET KL5KUSB101: Fix mem leak in error path of kaweth_download_firmware()
pch_gbe: don't use flush_scheduled_work()
bnx2: Always set ETH_FLAG_TXVLAN
net: clear heap allocation for ethtool_get_regs()
ipv6: Always clone offlink routes.
dcbnl: make get_app handling symmetric for IEEE and CEE DCBx
tcp: fix bug in listening_get_next()
inetpeer: Use correct AVL tree base pointer in inet_getpeer().
GRO: fix merging a paged skb after non-paged skbs
...
R6xx+ have per-block swappers. BE content in the
framebuffer will now be swapped properly during scanout.
Untested, however, the same code is reported working in
the UMS ddx.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@gmail.com>
Force DVI mode if the user specifies radeon.audio=0. The driver
doesn't handle HDMI mode properly in some cases.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=27731
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@gmail.com>
Check if there is a big enough dp clock & enough dp lane to
drive the video mode provided.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Reviewed-By: Alex Deucher <alexdeucher@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: Dave Airlie <airlied@gmail.com>
On PPC for example, AER is not supported and we see unnecessary AER
error message without this patch:
bnx2 0003:01:00.1: pci_cleanup_aer_uncorrect_error_status failed 0xfffffffb
Reported-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The chip's page tables did not set up properly on big endian machines,
causing EEH errors on PPC machines.
Reported-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch pivots the tg3 driver to the new VLAN infrastructure.
All references to vlgrp have been removed. The driver still attempts to
disable VLAN tag stripping if CONFIG_VLAN_8021Q or
CONFIG_VLAN_8021Q_MODULE is not defined.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'drm-nouveau-next' of git://git.freedesktop.org/git/nouveau/linux-2.6:
drm/nvc0/grctx: correct an off-by-one
drm/nv50: Fix race with PFIFO during PGRAPH context destruction.
drm/nouveau: Workaround incorrect DCB entry on a GeForce3 Ti 200.
drm/nvc0: implement irq handler for whatever's at 0x14xxxx
drm/nvc0: fix incorrect TPC register setup
drm/nouveau: probe for adt7473 before f75375
drm/nouveau: remove dead function definition
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: wacom - pass touch resolution to clients through input_absinfo
Input: wacom - add 2 Bamboo Pen and touch models
Input: sysrq - ensure sysrq_enabled and __sysrq_enabled are consistent
Input: sparse-keymap - fix KEY_VSW handling in sparse_keymap_setup
Input: tegra-kbc - add tegra keyboard driver
Input: gpio_keys - switch to using request_any_context_irq
Input: serio - allow registered drivers to get status flag
Input: ct82710c - return proper error code for ct82c710_open
Input: bu21013_ts - added regulator support
Input: bu21013_ts - remove duplicate resolution parameters
Input: tnetv107x-ts - don't treat NULL clk as an error
Input: tnetv107x-keypad - don't treat NULL clk as an error
Fix up trivial conflicts in drivers/input/keyboard/Makefile due to
additions of tc3589x/Tegra drivers
The bfin_sdh driver allocates the wrong size for the private data
in the mmc_host. The first parameter of mmc_alloc_host should be
the size of the local driver struct rather than the common mmc_host.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: <stable@kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
We have 8-bit width support but is not a v3 controller.
So we need platform_8bit_width() to support 8-bit buswidth.
Also we need MMC_CAP_8_BIT_DATA, so we add it in platdata.
This gets 8-bit support working again on s3c, after we previously
disabled 8-bit by default on non-v3 controllers.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
clk_get() returns a struct clk cookie to the driver and some platforms
may return NULL if they only support a single clock. clk_get() has only
failed if it returns a ERR_PTR() encoded pointer.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Don't read the command response from the registers when either the
command timed out (because there was no response from the card) or
the checksum on the response was invalid.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Chris Ball <cjb@laptop.org>
Including usb.h once is enough in drivers/mmc/host/ushc.c
This removes the duplicate.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Chris Ball <cjb@laptop.org>
Also remove fake ABS_RX/ABS_RY "axes" that were used to report physical
dimensions now that we have better way.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The -rt patches change the console_semaphore to console_mutex. As a
result, a quite large chunk of the patches changes all
acquire/release_console_sem() to acquire/release_console_mutex()
This commit makes things use more neutral function names which dont make
implications about the underlying lock.
The only real change is the return value of console_trylock which is
inverted from try_acquire_console_sem()
This patch also paves the way to switching console_sem from a semaphore to
a mutex.
[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: make console_trylock return 1 on success, per Geert]
Signed-off-by: Torben Hohn <torbenh@gmx.de>
Cc: Thomas Gleixner <tglx@tglx.de>
Cc: Greg KH <gregkh@suse.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
setup_irq() was called before clockevents_register_device() which is
needed by the irq handler. Bug was reproducible by restarting the
kernel using kexec (reliable crash).
Signed-off-by: Nikolaus Voss <n.voss@weinmann.de>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Both pps_parport and pps_gen_parport are written in a way that they
can't share a port with any other driver. This can result in locking up
the process that loads modules or even the whole kernel if the modules
are compiled in. Use PARPORT_FLAG_EXCL to indicate this.
Signed-off-by: Alexander Gordeev <lasaine@lvk.cs.msu.su>
Cc: Alexander Gordeev <lasaine@lvk.cs.msu.su>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
parport_unregister_device() should never be used when interrupts are
enabled in hardware and irq handler is registered so there is no need to
disable interrupts when using waitlist_lock. But there is no way to
explain this subtle semantics to lockdep analyzer.
So disable interrupts here too to simplify things. The price is
negligible.
Signed-off-by: Alexander Gordeev <lasaine@lvk.cs.msu.su>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Latest kernel has many changes in IRQ subsystem and its interfaces, like
adding "irq_eoi" for struct irq_chip, this patch is a follow up change
for that.
Also remove the unnecessary cast for a "void *".
Signed-off-by: Feng Tang <feng.tang@intel.com>
Cc: Alek Du <alek.du@intel.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Return PTR_ERR(led_dat->pwm) instead of 0 if pwm_request failed
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Luotao Fu <l.fu@pengutronix.de>
Cc: Reviewed-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'fixes' of master.kernel.org:/home/rmk/linux-2.6-arm:
ALSA: AACI: fix timeout duration
ALSA: AACI: fix timeout condition checking
ARM: 6636/1: ep93xx: default multiplexed gpio ports to gpio mode
ARM: 6637/1: Make the argument to virt_to_phys() "const volatile"
ARM: twd: ensure timer reload is reprogrammed on entry to periodic mode
ARM: 6635/2: Configure reference clock for Versatile Express timers
ARM: versatile: name configuration options after actual board names
ARM: realview: name configuration options after actual board names
ARM: realview,vexpress: fix section mismatch warning for pen_release
ARM: 6632/3: mmci: stop using the blockend interrupts
* 'sh-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
sh: Fix build of sh7750 base boards
sh: update INTC to clear IRQ sense valid flag
sh: Fix sh build failure when CONFIG_SFC=m
sh: fix MSIOF0 SPI on ecovec: it conflicts with VOU
sh: support XZ-compressed kernel.
sh: Fix up breakage from asm-generic/pgtable.h changes.
busy_loop() returns negative error code, thus change err variable
from u32 to int to properly propagate correct error code.
Also remove unneeded initialization for err and i variables.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds the device id for the windy31 USB device to the rt73usb
driver.
Thanks to Ralf Flaxa for reporting this and providing testing and a
sample device.
Reported-by: Ralf Flaxa <rf@suse.de>
Tested-by: Ralf Flaxa <rf@suse.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch (as1445) fixes a bug in the runtime PM core left over from
the addition of the no_callbacks flag. If this flag is set then it is
possible for rpm_suspend() to be called in_interrupt, so when
releasing spinlocks it's important not to re-enable interrupts.
To avoid an unnecessary save-and-restore of the interrupt flag, the
patch also inlines a pm_request_idle() call.
This fixes Bugzilla #27482.
(The offending code was added in 2.6.37, so it's not necessary to apply
this to any earlier stable kernels.)
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: tim blechmann <tim@klingt.org>
CC: <stable@kernel.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Based on a patch by Takashi Iwai.
Reported-by: Matthias Hopf <mat@mshopf.de>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=27272
Tested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Upon resume, like after a cold boot, we need to forcibly probe the
analog connector and cannot rely on the hotplug status.
Based on a patch by Takashi Iwai.
Reported-by: Stefan Dirsch <sndirsch@suse.de>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=26952
Tested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Call drm_mode_config_reset() after an invalidation event to restore any
cached state to unknown.
Tested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Iterate over the attached CRTCs, encoders and connectors and call the
supplied reset vfunc in order to reset any cached state back to unknown.
Useful after an invalidation event such as a GPU reset or resuming.
Tested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We were not pausing after detecting the response was pending and so did
not allow the hardware sufficient time to complete before aborting. This
lead to transient failures whilst probing SDVO devices.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=30235
Reported-by: Knut Petersen <Knut_Petersen@t-online.de>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Turn down the no IRQ message - on some platforms that's a normal state of
affairs.
Signed-off-by: Kalhan Trisal <kalhan.trisal@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
We will leak the storage allocated by request_firmware() if the size of
the firmware is greater than KAWETH_FIRMWARE_BUF_SIZE.
This removes the leak by calling release_firmware() before we return
-ENOSPC.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Directly cancel adapter->reset_task instead of using to-be-deprecated
flush_scheduled_work().
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
TSO does not work if the VLAN tag is in the packet (non-accelerated).
We may be able to remove this restriction in future firmware.
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now vgacon_scrollback_startup() uses slab, not bootmem,
the comment above it is obsolete, so does __init_refok.
Signed-off-by: WANG Cong <amwang@redhat.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
lcd_device_register may return ERR_PTR, so a check is added for this value
before the dereference. All of the other changes reorganize the error
handling code in this function to avoid duplicating all of it in the added
case.
In the original code, in one case, the global variable fb_buffer was set to
NULL in error code that appears after this variable is initialized. This
is done now in all error handling code that has this property.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
identifier f;
@@
f(...) { ... return ERR_PTR(...); }
@@
identifier r.f, fld;
expression x;
statement S1,S2;
@@
x = f(...)
... when != IS_ERR(x)
(
if (IS_ERR(x) ||...) S1 else S2
|
*x->fld
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Current implementation calls pxa168fb_check_var twice in pxa168fb_probe.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Current implementation puts CONFIG_CPU_FREQ at wrong place, CONFIG_CPU_FREQ
is for lcd_da8xx_cpufreq_deregister not for unregister_framebuffer.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Fixes the DVI-D output on that board (fdo bug 32645).
Reported-by: Bryan Quigley <BryanQuigley@Ubuntu.com>
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This is just barely enough to stop a never-ending IRQ storm that can
be triggered by our 3D driver. We have no idea what this engine is..
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Was hitting TPC+1's regs by accident, oops.
Reported-by: Christoph Bumiller <e0425955@student.tuwien.ac.at>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
There's a reported case where probing for f75375 causes the system
to hang completely, in this case there's an adt7473 at the same
i2c address.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
* 'for-38-rc3' of git://codeaurora.org/quic/kernel/davidb/linux-msm:
drivers: mmc: msm: remove clock disable in probe
mmc: msm: fix dma usage not to use internal APIs
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon/kms: add new radeon_info ioctl query for clock crystal freq
drm/i915: Prevent uninitialised reads during error state capture
drm/i915: Use consistent mappings for OpRegion between ACPI and i915
drm/i915: Handle the no-interrupts case for UMS by polling
drm/i915: Disable high-precision vblank timestamping for UMS
drm/i915: Increase the amount of defense before computing vblank timestamps
drm/i915,agp/intel: Do not clear stolen entries
drm/radeon/kms: simplify atom adjust pll setup
drm/radeon/kms: match r6xx/r7xx/evergreen asic_reset with previous asics
drm/radeon/kms: make the mac rv630 quirk generic
drm/radeon/kms: fix a spelling error in an error message
drm/radeon/kms: Initialize pageflip spinlocks.
drm/i915: Recognise non-VGA display devices
drm/i915: Fix use of invalid array size for ring->sync_seqno
drm/i915/ringbuffer: Fix use of stale HEAD position whilst polling for space
drm/i915: Don't kick-off hangcheck after a DRI interrupt
drm/i915: Add dependency on CONFIG_TMPFS
drm/i915: Initialise ring vfuncs for old DRI paths
drm/i915: make the blitter report buffer modifications to the FBC unit
drm/i915: set more FBC chicken bits
* 'drm-intel-fixes-2' of ssh://master.kernel.org/pub/scm/linux/kernel/git/ickle/drm-intel: (30 commits)
drm/i915: Prevent uninitialised reads during error state capture
drm/i915: Use consistent mappings for OpRegion between ACPI and i915
drm/i915: Handle the no-interrupts case for UMS by polling
drm/i915: Disable high-precision vblank timestamping for UMS
drm/i915: Increase the amount of defense before computing vblank timestamps
drm/i915,agp/intel: Do not clear stolen entries
Remove MAYBE_BUILD_BUG_ON
BUILD_BUG_ON: make it handle more cases
module: fix missing semicolons in MODULE macro usage
param: add null statement to compiled-in module params
module: fix linker error for MODULE_VERSION when !MODULE and CONFIG_SYSFS=n
module: show version information for built-in modules in sysfs
selinux: return -ENOMEM when memory allocation fails
tpm: fix panic caused by "tpm: Autodetect itpm devices"
TPM: Long default timeout fix
trusted keys: Fix a memory leak in trusted_update().
keys: add trusted and encrypted maintainers
encrypted-keys: rename encrypted_defined files to encrypted
trusted-keys: rename trusted_defined files to trusted
drm/i915: Recognise non-VGA display devices
...
This patch adds several new device ids to the r8712u staging driver.
The new ids were retrieved from latest vendor driver (v2.6.6.0.20101111)
downloadable from www.realtek.com.tw
Signed-off-by: Axel Koellhofer <AxelKoellhofer@web.de>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@kernel.org> [2.6.37]
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix a shutdown regression caused by 2a2d31c8dc ("intel_idle: open
broadcast clock event"). The clockevent framework can automatically
shutdown broadcast timers for hotremove CPUs. And we get a shutdown
regression when we shutdown broadcast timer for hot remove CPU, so just
delete some code.
Also fix some section mismatch.
Reported-by: Ari Savolainen <ari.m.savolainen@gmail.com>
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Tested-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
error_bo and pinned_bo could be used uninitialised if there were no
active buffers.
Caught by kmemcheck.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The opregion is a shared memory region between ACPI and the graphics
driver. As the ACPI mapping has been changed to cachable in commit
6d5bbf00d2, mapping the intel opregion
non-cachable now fails. As no bus-master hardware is involved in the
opregion, cachable map should do no harm.
Tested on a Fujitsu Lifebook P8010.
Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de>
[ickle: convert to acpi_os_ioremap for consistency]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Merge with Linus to resolve conflicting fixes for the reusing the stale
HEAD value during intel_ring_wait().
Conflicts:
drivers/gpu/drm/i915/intel_ringbuffer.c
If the driver calls into the kernel to wait for a breadcrumb to pass,
but hasn't enabled interrupts, fallback to polling the breadcrumb value.
Reported-by: Chris Clayton <chris2553@googlemail.com>
Tested-by: Chris Clayton <chris2553@googlemail.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We only have sufficient information for accurate (sub-frame) timestamping
when the modesetting is under our control.
Reported-by: Chris Clayton <chris2553@googlemail.com>
Tested-by: Chris Clayton <chris2553@googlemail.com>
Reviewed-by: Mario Kleiner <mario.kleiner@tuebingen.mpg.de>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reported-by: Chris Clayton <chris2553@googlemail.com>
Tested-by: Chris Clayton <chris2553@googlemail.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We can only utilize the stolen portion of the GTT if we are in sole
charge of the hardware. This is only true if using GEM and KMS,
otherwise VESA continues to access stolen memory.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Reported-by: Frederic Weisbecker <fweisbec@gmail.com>
Tested-by: Jiri Olsa <jolsa@redhat.com>
Tested-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
libsas makes use of scsi_schedule_eh() but forgets to clear the
host_eh_scheduled flag in its error handling routine. Because of this,
the error handler thread never gets to sleep; it's constantly awake and
trying to run the error routine leading to console spew and inability to
run anything else (at least on a UP system). The fix is to clear the
flag as we splice the work queue.
Cc: stable@kernel.org
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Currently sysrq_enabled and __sysrq_enabled are initialised separately
and inconsistently, leading to sysrq being actually enabled by reported
as not enabled in sysfs. The first change to the sysfs configurable
synchronises these two:
static int __read_mostly sysrq_enabled = 1;
static int __sysrq_enabled;
Add a common define to carry the default for these preventing them becoming
out of sync again. Default this to 1 to mirror previous behaviour.
Signed-off-by: Andy Whitcroft <apw@canonical.com>
Cc: stable@kernel.org
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
[jejb: fix up patch problems and checkpatch.pl issues]
Signed-off-by: Nick Cheng <nick.cheng@areca.com.tw>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
