This avoids a warning when building with -Wimplicit-fallthrough.
Fixes: 883a2a80f7 ("Input: elantech - enable SMBus on new (2018+) systems")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
There are some new HP laptops with Elantech touchpad that don't support
multitouch.
Currently we use ETP_NEW_IC_SMBUS_HOST_NOTIFY() to check if SMBus is supported,
but in addition to firmware version, the bus type also informs us whether the IC
can support SMBus. To avoid breaking old ICs, we will only enable SMbus support
based the bus type on systems manufactured after 2018.
Lastly, let's consolidate all checks into elantech_use_host_notify() and use it
to determine whether to use PS/2 or SMBus.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In the function alps_is_cs19_trackpoint(), we check if the param[1] is
in the 0x20~0x2f range, but the code we wrote for this checking is not
correct:
(param[1] & 0x20) does not mean param[1] is in the range of 0x20~0x2f,
it also means the param[1] is in the range of 0x30~0x3f, 0x60~0x6f...
Now fix it with a new condition checking ((param[1] & 0xf0) == 0x20).
Fixes: 7e4935ccc3 ("Input: alps - don't handle ALPS cs19 trackpoint-only device")
Cc: stable@vger.kernel.org
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
trackpoint_detect() should be static inline while
CONFIG_MOUSE_PS2_TRACKPOINT is not set, otherwise, we build fails:
drivers/input/mouse/alps.o: In function `trackpoint_detect':
alps.c:(.text+0x8e00): multiple definition of `trackpoint_detect'
drivers/input/mouse/psmouse-base.o:psmouse-base.c:(.text+0x1b50): first defined here
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 55e3d9224b ("Input: psmouse - allow disabing certain protocol extensions")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
On a latest Lenovo laptop, the trackpoint and 3 buttons below it
don't work at all, when we move the trackpoint or press those 3
buttons, the kernel will print out:
"Rejected trackstick packet from non DualPoint device"
This device is identified as an alps touchpad but the packet has
trackpoint format, so the alps.c drops the packet and prints out
the message above.
According to XiaoXiao's explanation, this device is named cs19 and
is trackpoint-only device, its firmware is only for trackpoint, it
is independent of touchpad and is a device completely different from
DualPoint ones.
To drive this device with mininal changes to the existing driver, we
just let the alps driver not handle this device, then the trackpoint.c
will be the driver of this device if the trackpoint driver is enabled.
(if not, this device will fallback to a bare PS/2 device)
With the trackpoint.c, this trackpoint and 3 buttons all work well,
they have all features that the trackpoint should have, like
scrolling-screen, drag-and-drop and frame-selection.
Signed-off-by: XiaoXiao Liu <sliuuxiaonxiao@gmail.com>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl0idTweHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGZesIAJDKicw2Voyx8K8m
3pXSK+71RuO/d3Y9M51mdfTMKRP4PHR9/4wVZ9wHPwC4dV6wxgsmIYCF69a1Wety
LD1MpDCP1DK5wVfPNKVX2xmj7ua6iutPtSsJHzdzM2TlscgsrFKjmUccqJ5JLwL5
c34nqwXWnzzRyI5Ga9cQSlwzAXq0vDHXyML3AnCosSsLX0lKFrHlK1zttdOPNkfj
dXRN62g3q+9kVQozzhDXb8atZZ7IkBk8Q0lujpNXW83Ci1VjaVNv3SB8GZTXIlLj
U15VdyuwfJDfpBgFBN6/unzVaAB6FFrEKy0jT1aeTyKarMKDKgOnJjn10aKjDNno
/bXsKKc=
=TVqV
-----END PGP SIGNATURE-----
Merge tag 'v5.2' into next
Sync up with mainline to resolve conflicts in iforce driver.
Probable cut&paste typo - use the correct field size.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Adds the Lenovo T580 to the SMBus intertouch list for Synaptics
touchpads. I've tested with this for a week now, and it seems a great
improvement. It's also nice to have the complaint gone from dmesg.
Signed-off-by: Nick Black <dankamongmen@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Thinkpad t480 laptops had some touchpad features disabled, resulting in the
loss of pinch to activities in GNOME, on wayland, and other touch gestures
being slower. This patch adds the touchpad of the t480 to the smbus_pnp_ids
whitelist to enable the extra features. In my testing this does not break
suspend (on fedora, with wayland, and GNOME, using the rc-6 kernel), while
also fixing the feature on a T480.
Signed-off-by: Cole Rogers <colerogers@disroot.org>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Elan_i2c and hid-quirks work in conjunction to decide which devices each
driver will handle. Elan_i2c has a whitelist of devices that should be
consumed by hid-quirks so that there is one master list of devices to
handoff between the drivers. Put the ids in a header file so that
hid-quirks can consume it instead of duplicating the list.
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Another round of SPDX updates for 5.2-rc6
Here is what I am guessing is going to be the last "big" SPDX update for
5.2. It contains all of the remaining GPLv2 and GPLv2+ updates that
were "easy" to determine by pattern matching. The ones after this are
going to be a bit more difficult and the people on the spdx list will be
discussing them on a case-by-case basis now.
Another 5000+ files are fixed up, so our overall totals are:
Files checked: 64545
Files with SPDX: 45529
Compared to the 5.1 kernel which was:
Files checked: 63848
Files with SPDX: 22576
This is a huge improvement.
Also, we deleted another 20000 lines of boilerplate license crud, always
nice to see in a diffstat.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXQyQYA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymnGQCghETUBotn1p3hTjY56VEs6dGzpHMAnRT0m+lv
kbsjBGEJpLbMRB2krnaU
=RMcT
-----END PGP SIGNATURE-----
Merge tag 'spdx-5.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx
Pull still more SPDX updates from Greg KH:
"Another round of SPDX updates for 5.2-rc6
Here is what I am guessing is going to be the last "big" SPDX update
for 5.2. It contains all of the remaining GPLv2 and GPLv2+ updates
that were "easy" to determine by pattern matching. The ones after this
are going to be a bit more difficult and the people on the spdx list
will be discussing them on a case-by-case basis now.
Another 5000+ files are fixed up, so our overall totals are:
Files checked: 64545
Files with SPDX: 45529
Compared to the 5.1 kernel which was:
Files checked: 63848
Files with SPDX: 22576
This is a huge improvement.
Also, we deleted another 20000 lines of boilerplate license crud,
always nice to see in a diffstat"
* tag 'spdx-5.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx: (65 commits)
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 507
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 506
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 505
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 504
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 503
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 502
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 501
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 500
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 499
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 498
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 497
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 496
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 495
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 491
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 490
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 489
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 488
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 487
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 486
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 485
...
Pull input updates from Dmitry Torokhov:
"Just a few small fixups and switching a couple of Thinkpads to SMBus
for touchpads as PS/2 emulation is not working well"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: synaptics - enable SMBus on ThinkPad E480 and E580
Input: imx_keypad - make sure keyboard can always wake up system
Input: iqs5xx - get axis info before calling input_mt_init_slots()
Input: uinput - add compat ioctl number translation for UI_*_FF_UPLOAD
Input: silead - add MSSL0017 to acpi_device_id
Input: elantech - enable middle button support on 2 ThinkPads
Input: elan_i2c - increment wakeup count if wake source
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
They are capable of using intertouch and it works well with
psmouse.synaptics_intertouch=1, so add them to the list.
Without it, scrolling and gestures are jumpy, three-finger pinch gesture
doesn't work and three- or four-finger swipes sometimes get stuck.
Signed-off-by: Alexander Mikhaylenko <exalm7659@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not write to the free software foundation inc
59 temple place suite 330 boston ma 02111 1307 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1334 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.113240726@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Both now works correctly over SMBus. Let's use this driver so we can
update all five fingers every 8ms.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Some models have a middle button, we should export it as well.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The recent touchpads might not have all the information regarding the
characteristics through the I2C port.
On some Lenovo t480s, this results in the touchpad not being detected
as a clickpad, and on the Lenovo P52, this results in a failure while
fetching the resolution through I2C.
We need to imitate the Windows behavior: fetch the data under PS/2, and
limit the querries under I2C.
This patch prepares this by exporting the info from PS/2.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
See the previous patch for a long explanation.
TL;DR: the P52 and the t480s from Lenovo can't rely on I2C to fetch
the information, so we need it from PS/2.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Looks like the new generation of Lenovo machine also need to
be added to the PnPID whitelist. This is definitively not going
to scale, as there is nothing that tells us currently if a
touchpad supports a true physical middle button.
Consider that all new touchpads that are not clickpads
(so matching ETP_NEW_IC_SMBUS_HOST_NOTIFY) are handling 3 physical
buttons.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We check for this bit all over the code, better have it defined once
for all.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
For the latest generation of Elantech touchpads, we need to forward
the min/max information from PS/2 to SMBus. Prepare this work
by fetching the information before creating the SMBus companion
device.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not write to the free software foundation inc
675 mass ave cambridge ma 02139 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 441 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190520071858.739733335@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all files which:
- Have no license information of any form
- Have MODULE_LICENCE("GPL*") inside which was used in the initial
scan/conversion to ignore the file
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Notify the PM core that this device is the wake source. This helps
userspace daemon tracking the wake sources to identify the origin of the
wake.
Signed-off-by: Ravi Chandra Sadineni <ravisadineni@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Instead of signalling wakeup directly from i8042, let psmouse and atkbd
drivers execute basic protocol handling and only then signal wakeup
condition. This solves the issue where we increment wakeup counter
simply because we are getting responses from keyboard/mouse to the
commands we ourselves send to them as part of suspend transition.
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
There are many Lenovo laptops which need elan_i2c support, this patch adds
relevant IDs to the Elan driver so that touchpads are recognized.
Signed-off-by: KT Liao <kt.liao@emc.com.tw>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Lenovo s21e-20 uses ELAN0601 in its ACPI tables for the Elan touchpad.
Signed-off-by: Vincent Batts <vbatts@hashbangbash.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Remove a leftover spinlock.
This was required back when mod_delayed_work() did not exist, and had to
be implemented with a cancel + queue. See commit e7c2f96744
("workqueue: use mod_delayed_work() instead of __cancel + queue")
schedule_delayed_work() and mod_delayed_work() can now be used
concurrently. So the spinlock is no longer needed.
Signed-off-by: Sven Van Asbroeck <TheSven73@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This adds ELAN0617 to the ACPI table to support Elan touchpad found in
Lenovo V330-15ISK.
Signed-off-by: Mauro Ciancio <mauro@acadeu.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This reverts commit 7db54c89f0 as it
breaks Acer Aspire V-371 and other devices. According to Elan:
"Acer Aspire F5-573G is MS Precision touchpad which should use hid
multitouch driver. ELAN0501 should not be added in elan_i2c."
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=202503
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Like Fujitsu CELSIUS H760, the H780 also has a three-button Elantech
touchpad, but the driver needs to be told so to enable the middle touchpad
button.
The elantech_dmi_force_crc_enabled quirk was not necessary with the H780.
Also document the fw_version and caps values detected for both H760 and
H780 models.
Signed-off-by: Matti Kurkela <Matti.Kurkela@iki.fi>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAlwgIJYeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG0F4H/jwv83AI9qxd4Zsj
geztCq0w1Vc48Gz/yDvl5MxZ74//q7Wz01qRTKisMNJla+Z0VuUReL12w0BGT0ko
ZwPqrvPtM04pA7A6J+vLM8t6k7Ck0q7xC3z/Y9eN5qxtC7yOX/X8RziiXBmyMzM5
nVpFYQwlk9/hSUHjPwMgf2dV32vNYl3FEph3g6nrqQLLdtsHiii9N8rC+cAU2jKg
sZ8Cp6REYYxt9LWEilsGof+oLnH+oUkXecB7WKKvSaAVHqR20xdpZ3ZvRcVyLfQ4
XCXBu8PIYYBWsa/iwuu0h4NuosGzEYbWOjnXKozOaV2KoqCT/Rk1egKIgb55EpyA
kFH4wfc=
=WAE7
-----END PGP SIGNATURE-----
Merge tag 'v4.20' into for-linus
Sync with mainline to get linux/overflow.h among other things.
This adds ELAN0501 to the ACPI table to support Elan touchpad found in ASUS
Aspire F5-573G.
Signed-off-by: Patrick Dreyer <Patrick.Dreyer@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input fixes from Dmitry Torokhov:
"Switching a few devices with Synaptics over to SMbus and disabling
SMbus on a couple devices with Elan touchpads as they need more
plumbing on PS/2 side"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: synaptics - enable SMBus for HP EliteBook 840 G4
Input: elantech - disable elan-i2c for P52 and P72
Input: synaptics - enable RMI on ThinkPad T560
Input: omap-keypad - fix idle configuration to not block SoC idle states
dmesg reports that "Your touchpad (PNP: SYN3052 SYN0100 SYN0002 PNP0f13)
says it can support a different bus."
I've tested the offered psmouse.synaptics_intertouch=1 with 4.18.x and
4.19.x and it seems to work well. No problems seen with suspend/resume.
Also, it appears that RMI/SMBus mode is actually required for 3-4 finger
multitouch gestures to work -- otherwise they are not reported at all.
Information from dmesg in both modes:
psmouse serio3: synaptics: Touchpad model: 1, fw: 8.2, id: 0x1e2b1,
caps: 0xf00123/0x840300/0x2e800/0x0, board id: 3139, fw id: 2000742
psmouse serio3: synaptics: Trying to set up SMBus access
rmi4_smbus 6-002c: registering SMbus-connected sensor
rmi4_f01 rmi4-00.fn01: found RMI device,
manufacturer: Synaptics, product: TM3139-001, fw id: 2000742
Signed-off-by: Mantas Mikulėnas <grawity@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The current implementation of elan_i2c is known to not support those
2 laptops.
A proper fix is to tweak both elantech and elan_i2c to transmit the
correct information from PS/2, which would make a bad candidate for
stable.
So to give us some time for fixing the root of the problem, disable
elan_i2c for the devices we know are not behaving properly.
Link: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1803600
Link: https://bugs.archlinux.org/task/59714
Fixes: df077237cf Input: elantech - detect new ICs and setup Host Notify for them
Cc: stable@vger.kernel.org # v4.18+
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Before commit 7fd6d98b89 ("i2c: i801: Allow ACPI AML access I/O
ports not reserved for SMBus"), enabling RMI on the T560 would cause
the touchpad to stop working after resuming from suspend. Now that
this issue is fixed, RMI can be enabled safely and works fine.
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Yussuf Khalil <dev@pp3345.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input updates from Dmitry Torokhov:
"Mostly new IDs for Elan/Synaptics touchpads, plus a few small fixups"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: omap-keypad - fix keyboard debounce configuration
Input: xpad - quirk all PDP Xbox One gamepads
Input: synaptics - enable SMBus for HP 15-ay000
Input: synaptics - add PNP ID for ThinkPad P50 to SMBus
Input: elan_i2c - add ACPI ID for Lenovo IdeaPad 330-15ARR
Input: elan_i2c - add support for ELAN0621 touchpad
Input: hyper-v - fix wakeup from suspend-to-idle
Input: atkbd - clean up indentation issue
Input: st1232 - convert to SPDX identifiers
Input: migor_ts - convert to SPDX identifiers
Input: dt-bindings - fix a typo in file input-reset.txt
Input: cros_ec_keyb - fix button/switch capability reports
Input: elan_i2c - add ELAN0620 to the ACPI table
Input: matrix_keypad - check for errors from of_get_named_gpio()
SMBus works fine for the touchpad with id SYN3221, used in the HP 15-ay000
series,
This device has been reported in these messages in the "linux-input"
mailing list:
* https://marc.info/?l=linux-input&m=152016683003369&w=2
* https://www.spinics.net/lists/linux-input/msg52525.html
Reported-by: Nitesh Debnath <niteshkd1999@gmail.com>
Reported-by: Teika Kazura <teika@gmx.com>
Signed-off-by: Teika Kazura <teika@gmx.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Noticed the other day the trackpoint felt different on my P50, then
realized it was because rmi4 wasn't loading for this machine
automatically. Suspend/resume, hibernate, and everything else seem to
work perfectly fine on here.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add ELAN061E to the ACPI table to support Elan touchpad found in Lenovo
IdeaPad 330-15ARR.
Signed-off-by: Noah Westervelt <nwestervelt@outlook.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Added the ability to detect the ELAN0621 touchpad found in some Lenovo
laptops.
Signed-off-by: Adam Wong <adam@adamwong.me>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add ELAN0620 to the ACPI table to support the elan touchpad in
the Lenovo IdeaPad 130-15IKB.
Signed-off-by: Patrick Gaskin <patrick@pgaskin.net>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Dmitry writes:
"Input updates for 4.19-rc8
Just an addition to elan touchpad driver ACPI table."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: elan_i2c - add ACPI ID for Lenovo IdeaPad 330-15IGM
synaptics_detect() does not check whether sending commands to the
device succeeds and instead relies on getting unique data from the
device. Let's make sure we seed entire buffer with zeroes to make sure
we will not use garbage on stack that just happen to be 0x47.
Reported-by: syzbot+13cb3b01d0784e4ffc3f@syzkaller.appspotmail.com
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add ELAN061C to the ACPI table to support Elan touchpad found in Lenovo
IdeaPad 330-15IGM.
Signed-off-by: Mikhail Nikiforov <jackxviichaos@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Notice that in this particular case, I replaced the "Fallthrough state"
commern with a proper "Fall through", which is what GCC is expecting to
find.
Addresses-Coverity-ID: 114758 ("Missing break in switch")
Addresses-Coverity-ID: 114759 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Dmitry writes:
"Input updates for v4.19-rc5
Just a few driver fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: uinput - allow for max == min during input_absinfo validation
Input: elantech - enable middle button of touchpad on ThinkPad P72
Input: atakbd - fix Atari CapsLock behaviour
Input: atakbd - fix Atari keymap
Input: egalax_ts - add system wakeup support
Input: gpio-keys - fix a documentation index issue
Adding 2 new touchpad IDs to support middle button support.
Cc: stable@vger.kernel.org
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input updates from Dmitry Torokhov:
- a new driver for Rohm BU21029 touch controller
- new bitmap APIs: bitmap_alloc, bitmap_zalloc and bitmap_free
- updates to Atmel, eeti. pxrc and iforce drivers
- assorted driver cleanups and fixes.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (57 commits)
MAINTAINERS: Add PhoenixRC Flight Controller Adapter
Input: do not use WARN() in input_alloc_absinfo()
Input: mark expected switch fall-throughs
Input: raydium_i2c_ts - use true and false for boolean values
Input: evdev - switch to bitmap API
Input: gpio-keys - switch to bitmap_zalloc()
Input: elan_i2c_smbus - cast sizeof to int for comparison
bitmap: Add bitmap_alloc(), bitmap_zalloc() and bitmap_free()
md: Avoid namespace collision with bitmap API
dm: Avoid namespace collision with bitmap API
Input: pm8941-pwrkey - add resin entry
Input: pm8941-pwrkey - abstract register offsets and event code
Input: iforce - reorganize joystick configuration lists
Input: atmel_mxt_ts - move completion to after config crc is updated
Input: atmel_mxt_ts - don't report zero pressure from T9
Input: atmel_mxt_ts - zero terminate config firmware file
Input: atmel_mxt_ts - refactor config update code to add context struct
Input: atmel_mxt_ts - config CRC may start at T71
Input: atmel_mxt_ts - remove unnecessary debug on ENOMEM
Input: atmel_mxt_ts - remove duplicate setup of ABS_MT_PRESSURE
...
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Warning level 2 was used: -Wimplicit-fallthrough=2
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Comparing an int to a size, which is unsigned, causes the int to become
unsigned, giving the wrong result. i2c_smbus_read_block_data can return the
result of i2c_smbus_xfer, whih can return a negative error code.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
int x;
expression e,e1;
identifier f;
@@
*x = f(...);
... when != x = e1
when != if (x < 0 || ...) { ... return ...; }
*x < sizeof(e)
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
atp_open(), atp_recover() and atp_resume() are never called in atomic
context. They call usb_submit_urb() with GFP_ATOMIC, which is not
necessary. GFP_ATOMIC can be replaced with GFP_KERNEL.
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input fixes from Dmitry Torokhov:
- a couple of new device IDs added to Elan i2c touchpad controller
driver
- another entry in i8042 reset quirk list
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: i8042 - add Lenovo LaVie Z to the i8042 reset list
Input: elan_i2c - add another ACPI ID for Lenovo Ideapad 330-15AST
MAINTAINERS: Add file patterns for serio device tree bindings
Input: elan_i2c - add ACPI ID for lenovo ideapad 330
I do not think Vojtech wants snail mail these days (and he mentioned that
nobody has ever sent him snail mail), and the address is not even valid
anymore, so let's remove snail-mail instructions from the sources.
Acked-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add ELAN0622 to ACPI mapping table to support Elan touchpad found in
Ideapad 330-15AST.
Signed-off-by: KT Liao <kt.liao@emc.com.tw>
Reported-by: Anant Shende <anantshende@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This allows Elan driver to bind to the touchpad found in Lenovo Ideapad 330
series laptops.
Signed-off-by: Donald Shanty III <dshanty@protonmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input updates from Dmitry Torokhov:
- the main change is a fix for my brain-dead patch to PS/2 button
reporting for some protocols that made it in 4.17
- there is a new driver for Spreadtum vibrator that I intended to send
during merge window but ended up not sending the 2nd pull request.
Given that this is a brand new driver we should not see regressions
here
- a fixup to Elantech PS/2 driver to avoid decoding errors on Thinkpad
P52
- addition of few more ACPI IDs for Silead and Elan drivers
- RMI4 is switched to using IRQ domain code instead of rolling its own
implementation
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: psmouse - fix button reporting for basic protocols
Input: xpad - fix GPD Win 2 controller name
Input: elan_i2c_smbus - fix more potential stack buffer overflows
Input: elan_i2c - add ELAN0618 (Lenovo v330 15IKB) ACPI ID
Input: elantech - fix V4 report decoding for module with middle key
Input: elantech - enable middle button of touchpads on ThinkPad P52
Input: do not assign new tracking ID when changing tool type
Input: make input_report_slot_state() return boolean
Input: synaptics-rmi4 - fix axis-swap behavior
Input: synaptics-rmi4 - fix the error return code in rmi_probe_interrupts()
Input: synaptics-rmi4 - convert irq distribution to irq_domain
Input: silead - add MSSL0002 ACPI HID
Input: goldfish_events - fix checkpatch warnings
Input: add Spreadtrum vibrator driver
The commit ba667650c5 ("Input: psmouse - clean up code") was pretty
brain-dead and broke extra buttons reporting for variety of PS/2 mice:
Genius, Thinkmouse and Intellimouse Explorer. We need to actually inspect
the data coming from the device when reporting events.
Fixes: ba667650c5 ("Input: psmouse - clean up code")
Reported-by: Jiri Slaby <jslaby@suse.cz>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Commit 40f7090bb1 ("Input: elan_i2c_smbus - fix corrupted stack")
fixed most of the functions using i2c_smbus_read_block_data() to
allocate a buffer with the maximum block size. However three
functions were left unchanged:
* In elan_smbus_initialize(), increase the buffer size in the same
way.
* In elan_smbus_calibrate_result(), the buffer is provided by the
caller (calibrate_store()), so introduce a bounce buffer. Also
name the result buffer size.
* In elan_smbus_get_report(), the buffer is provided by the caller
but happens to be the right length. Add a compile-time assertion
to ensure this remains the case.
Cc: <stable@vger.kernel.org> # 3.19+
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add ELAN0618 to the list of supported touchpads; this ID is used in
Lenovo v330 15IKB devices.
Signed-off-by: Alexandr Savca <alexandr.savca@saltedge.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Some touchpad has middle key and it will be indicated in bit 2 of packet[0].
We need to fix V4 formation's byte mask to prevent error decoding.
Signed-off-by: KT Liao <kt.liao@emc.com.tw>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
PNPID is better way to identify the type of touchpads.
Enable middle button support on 2 types of touchpads on Lenovo P52.
Cc: stable@vger.kernel.org
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
As we move stuff around, some doc references are broken. Fix some of
them via this script:
./scripts/documentation-file-ref-check --fix
Manually checked if the produced result is valid, removing a few
false-positives.
Acked-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Coly Li <colyli@suse.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Add ELAN0612 to the list of supported touchpads; this ID is used in Lenovo
v330 14IKB devices.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=199253
Signed-off-by: Johannes Wienke <languitar@semipol.de>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAlsB91MeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGqLYH+gPrmb8gvH6CmckN
5U+RKRjzvs6oDqXf5yFUJ7NqW1Ex8qMuAqv1Kx2LpuN8sDD42fPB0A5OxijNgk81
omJIxqANbFPUQCt+epR1P5dp0XqbXCcIvmo9Dd2TM4EP0mcQqr+c61d7JXtVATMu
JrR5X7pgepatgH7JYI7fm1yIh/6RIhYZXjU2HxwiRHIzsLfW/sTmM4HZksv8nJjl
m+bT8XzEUCBhWCLT8z0TbbVug1N2qdyMzkMIS2JmDVJE4FZ9YOEnZzaCHGNZrkVV
OYzr94Bv2Z2PO3KIrsEsNA/szhr9/8f5Si9mk9nOi2kTuvaF9hhjKxcCozVB+ses
fm8wpmM=
=FiAO
-----END PGP SIGNATURE-----
Merge tag 'v4.17-rc6' into next
Sync up with mainline to bring in Atmel controller changes for Caroline.
This seems to be Synaptics specific, as some Elan touchpads are not
correctly switching to SMBus if we call deactivate before switching to
SMBus on cold boot and on resume.
Tested with the T480s
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: KT Liao <kt.liao@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
New ICs are using a different scheme for the alternate bus parameter.
Given that they are new and are only using either PS2 only or PS2 + SMBus
Host Notify, we force those new ICs to use the SMBus solution for enhanced
reporting.
This allows the touchpad found on the Lenovo T480s to report 5 fingers
every 8 ms, instead of having a limit of 2 every 8 ms.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: KT Liao <kt.liao@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Many of the Elantech devices are connected through PS/2 and a different
bus (SMBus or plain I2C).
To not break any existing device, we only enable SMBus based
on a module parameter. If some laptops require the quirk to
be set, we will have to rely on a list of PNPIds or MDI matching
to individually expose those hardware over SMBus.
the parameter mentioned above is elantech_smbus from the psmouse
module.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: KT Liao <kt.liao@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The command ETP_RESOLUTION_QUERY also contains the bus information.
It is better to fetch it once, while we are querying for device
information.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: KT Liao <kt.liao@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In preparation for SMBus device support, move static device
information that we query form the touchpad upon initialization into
separate structure. This will allow us to query the device without
allocating memory first.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: KT Liao <kt.liao@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The Elan touchpads over I2C/SMBus also can handle a trackstick.
Unfortunately, nothing tells us if the device supports trackstick (the
information lies in the PS/2 node), so rely on device properties to
determine whether to enable the trackstick node.
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1313939
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: KT Liao <kt.liao@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
New ICs (like the one on the Lenovo T480s) answer to
ETP_SMBUS_IAP_VERSION_CMD 4 bytes instead of 3. This corrupts the stack
as i2c_smbus_read_block_data() uses the values returned by the i2c
device to know how many data it need to return.
i2c_smbus_read_block_data() can read up to 32 bytes (I2C_SMBUS_BLOCK_MAX)
and there is no safeguard on how many bytes are provided in the return
value. Ensure we always have enough space for any future firmware.
Also 0-initialize the values to prevent any access to uninitialized memory.
Cc: <stable@vger.kernel.org> # v4.4.x, v4.9.x, v4.14.x, v4.15.x, v4.16.x
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: KT Liao <kt.liao@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This time, Lenovo decided to go with different pieces in its latest
series of Thinkpads.
For those we have been able to test:
- the T480 is using Synaptics with an IBM trackpoint
-> it behaves properly with or without intertouch, there is no point
not using RMI4
- the X1 Carbon 6th gen is using Synaptics with an IBM trackpoint
-> the touchpad doesn't behave properly under PS/2 so we have to
switch it to RMI4 if we do not want to have disappointed users
- the X280 is using Synaptics with an ALPS trackpoint
-> the recent fixes in the trackpoint handling fixed it so upstream
now works fine with or without RMI4, and there is no point not
using RMI4
- the T480s is using an Elan touchpad, so that's a different story
Cc: <stable@vger.kernel.org> # v4.14.x, v4.15.x, v4.16.x
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: KT Liao <kt.liao@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Synaptics devices reported it has Intertouch support,
and it fails via PS/2 as following logs:
psmouse serio2: Failed to reset mouse on synaptics-pt/serio0
psmouse serio2: Failed to enable mouse on synaptics-pt/serio0
Set these new devices to use SMBus to fix this issue, then they report
SMBus version 3 is using, patch:
https://patchwork.kernel.org/patch/9989547/ enabled SMBus ver 3 and
makes synaptics devices work fine on SMBus mode.
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Lenovo use two different trackpoints in the fifth generation Thinkpad X1
Carbon. Both are accessible over SMBUS/RMI but the pnpIDs are missing.
This patch is for the Elantech trackpoint specifically which also
reports SMB version 3 so rmi_smbus needs to be updated in order to
handle it.
For the record, I was not the first one to come up with this patch as it
has been floating around the internet for a while now. However, I have
spent significant time with testing and my efforts to find the original
author of the patch have been unsuccessful.
Signed-off-by: Edvard Holst <edvard.holst@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The touchpad on Lenovo Carbon X1 Gen 5 (2017 - Kabylake) is accessible over
SMBUS/RMI, so let's activate it by default.
Cc: stable@vger.kernel.org
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Remove cite "Not sure what this does, but it is absolutely essential".
Extract initialization of trackstick part when touchpad is in passthrough
mode for v3 and v6 protocols into own function. Initialization for v3 is:
setscale11, setscale11, setscale11, nibble 0x9, nibble 0x4. Initialization
for v6 is: setscale11, setscale11, setscale11, setrate 0xC8, setrate 0x14.
Nibbles 0x9 and 0x4 for v3 protocol correspond to setrate 0xC8 and 0x14,
therefore these sequences are same.
When touchpad is in passthrough mode, then OS communicates with trackstick
and this sequence is some magic vendor PS/2 command to put trackstick into
"extended" mode. After that sequence trackstick starts reporting packets in
some vendor 4 bytes format (first byte is always 0xE8).
Next step after configuring trackstick to be in "extended" mode, is to
configure touchpad for v3 protocol to expect that trackstick reports data
in "extended" mode. For v3 protocol this is done by setting bit 1 in
register 0xC2C8 (offset 0x08 from base address 0xC2C0).
When both touchpad and trackstick are not configured for "extended" mode
then touchpad reports trackstick packets in different format, which is not
supported by psmouse/alps driver (yet).
In Cirque documentation GP-AN- 130823 INTERFACING TO GEN4 OVER I2C (PDF)
available at http://www.cirque.com/gen4-dev-resources is Logical Address
0xC2C8 named as PS2AuxControl and Bit Number 1 as ProcessAuxExtendedData
with description: Auxiliary device data is assumed to be extended data when
set.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The primary interface for the touchpad device in Thinkpad L570 is SMBus,
so ALPS overlooked PS2 interface Firmware setting of TrackStick, and
shipped with TrackStick otp bit is disabled.
The address 0xD7 contains device number information, so we can identify
the device by checking this value, but to access it we need to enable
Command mode, and then re-enable the device. Devices shipped in Thinkpad
L570 report either 0x0C or 0x1D as device numbers, if we see them we assume
that the devices are DualPoints.
The same issue exists on Dell Latitude 7370.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=196929
Fixes: 646580f793 ("Input: ALPS - fix multi-touch decoding on SS4 plus touchpads")
Signed-off-by: Masaki Ota <masaki.ota@jp.alps.com>
Tested-by: Aaron Ma <aaron.ma@canonical.com>
Tested-by: Jonathan Liu <net147@gmail.com>
Tested-by: Jaak Ristioja <jaak@ristioja.ee>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
ALPS v3 and v7 packet formats reports trackstick pressure. This information
is already parsed in unused "z" variable.
ALPS SS4 S2 devices already reports trackstick pressure as ABS_PRESSURE
attribute, therefore reports pressure in the same way also for v3 and v7.
This patch also updates parsing v3 pressure information, it is also stored
in 7 bits.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
If the device is unused and suspended, a call to open will cause the
device to autoresume through the call to usb_autopm_get_interface().
input_dev->users is already incremented by the input subsystem,
therefore this expression will always be evaluated to true:
if ((input_dev->users || (synusb->flags & SYNUSB_IO_ALWAYS)) &&
usb_submit_urb(synusb->urb, GFP_NOIO) < 0) {
retval = -EIO;
}
The same URB will then be fail when resubmitted in synusb_open().
Introduce synusb->is_open to keep track of the state instead.
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
usb_autopm_get_interface() that is called in synusb_open() does an
autoresume if the device is suspended.
input_dev->mutex used in synusb_resume() is in this case already
taken by the input subsystem and will cause a deadlock.
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Assign true or false to boolean variables instead of an integer value.
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input fixes from Dmitry Torokhov:
- we are reverting patch that was switched touchpad on Lenovo T460P
over to native RMI because on these boxes BIOS messes up with SMBus
controller state. We might re-enable it later once SMBus issue is
resolved
- disabling interrupts in matrix_keypad driver was racy
- mms114 now has SPDX header and matching MODULE_LICENSE
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Revert "Input: synaptics - Lenovo Thinkpad T460p devices should use RMI"
Input: matrix_keypad - fix race when disabling interrupts
Input: mms114 - add SPDX identifier
Input: mms114 - fix license module information
This reverts commit 4828296982 which
caused the following issues:
1. On T460p with BIOS version 2.22 touchpad and trackpoint stop working
after suspend-resume cycle. Due to strange state of the device another
suspend is impossible.
The following dmesg errors can be observed:
thinkpad_acpi: EC reports that Thermal Table has changed
rmi4_smbus 7-002c: failed to get SMBus version number!
rmi4_physical rmi4-00: rmi_driver_reset_handler: Failed to read current IRQ mask.
rmi4_f01 rmi4-00.fn01: Failed to restore normal operation: -16.
rmi4_f01 rmi4-00.fn01: Resume failed with code -16.
rmi4_physical rmi4-00: Failed to suspend functions: -16
rmi4_smbus 7-002c: Failed to resume device: -16
PM: resume devices took 0.640 seconds
rmi4_f03 rmi4-00.fn03: rmi_f03_pt_write: Failed to write to F03 TX register (-16).
rmi4_physical rmi4-00: rmi_driver_clear_irq_bits: Failed to change enabled interrupts!
rmi4_physical rmi4-00: rmi_driver_set_irq_bits: Failed to change enabled interrupts!
psmouse: probe of serio3 failed with error -1
2. On another T460p with BIOS version 2.15 two finger scrolling gesture
on the touchpad stops working after suspend-resume cycle (about 75%
reproducibility, when it still works, the scrolling gesture becomes
laggy). Nothing suspicious appears in the dmesg.
Analysis form Richard Schütz:
"RMI is unreliable on the ThinkPad T460p because the device is affected
by the firmware behavior addressed in a7ae81952c ("i2c: i801: Allow
ACPI SystemIO OpRegion to conflict with PCI BAR")."
The affected devices often show:
i801_smbus 0000:00:1f.4: BIOS is accessing SMBus registers
i801_smbus 0000:00:1f.4: Driver SMBus register access inhibited
Reported-by: Richard Schütz <rschuetz@uni-koblenz.de>
Signed-off-by: Arkadiusz Hiler <arkadiusz.hiler@intel.com>
Tested-by: Martin Peres <martin.peres@linux.intel.com>
Tested-by: Arkadiusz Hiler <arkadiusz.hiler@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We do not need to call ps2_command() several times in a row, transmitting
every byte as it were a command byte, we can often pack it all in a single
command.
Also, now that ps2_command() handles retransmission, we do not need to do
it ourselves in trackpoint_power_on_reset().
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In preparation to adding some debugging statements to PS/2 control
sequences let's move psmouse_sliced_command() into libps2 and rename it
to ps2_sliced_command().
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This Far-Eastern company's PS/2 mice use a deviant format for the data
relating to movement of the scroll wheels for, at least, their dual wheel
mice, such as their "Optical GreatEye Wheelmouse" model "WOP-35". This
product has five "buttons" (one of which is the click action on the first
wheel) and TWO scroll wheels. However for a byte comprising d0-d7 instead
of setting one of d6-7 in the forth byte of the mouse data packet and a
twos complement number of scroll steps in the remaining d5-d0 (or d3-d0
should there be a fourth (BTN_SIDE - d4) or fifth (BTN_EXTRA - d5) button
to report; they only report a single +/- event for each wheel and use a bit
pattern that corresponds to +/-1 for the first wheel and +/- 2 for the
second in the lower nibble of the fourth byte.
The effect with existing code is that the second mouse wheel merely repeats
the effect of the first but providing two steps per click rather than the
one of the first wheel - so there is no HORIZONTAL scroll wheel movement
detected from the device as far as the rest of the kernel sees it.
This patch, if enabled by the "a4tech_workaround" module parameter modifies
the handling just for mice of type PSMOUSE_IMEX so that the second scroll
wheel movement gets correctly reported as REL_HWHEEL events. Should this
module parameter be activated for other mice of the same PSMOUSE_IMEX type
then it is possible that at the point where the mouse reports more than a
single movement step the user may start seeing horizontal rather than
vertical wheel events, but should the movement steps get to be more than
two at a time the hack will get immediately deactivated and the behaviour
will revert to the past code.
This was discussed around *fifteen* *years* *ago* on the LKML and the best
summary is in post https://lkml.org/lkml/2002/7/18/111 "Re: PS2 Input Core
Support" by Vojtech Pavlik. I was not able to locate any discussion later
than this on this topic.
Given that most users of the "psmouse" module will NOT want this additional
feature enabled I have taken the apparently erroneous step of defaulting
the module parameter that enables it to be "disabled" - this functionality
may interfere with the operation of "normal" mice of this type (until a
large enough scroll wheel movement is detected) so I cannot see how it
would want to be enabled for "normal" users - i.e. everyone without this
brand of mouse.
I am using this patch at the moment and I can confirm that it is working
for me as both a module and compiled into the kernel for my mouse that is
of the type (WOP-35) described - I note that it is still available from
certain on-line retailers and that the manufacturers site does not list
GNU/Linux as being supported on the product page - this patch however does
enable full use of this product:
http://www.a4tech.com/product.asp?cid=3D1&scid=3D8&id=3D22
Signed-off-by: Stephen Lyons <slysven@virginmedia.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
- use u8 instead of unsigned char for byte data
- use input_set_capability() instead of manipulating capabilities bits
directly
- do not abuse -1 as error code, propagate errors from various calls.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
- switch to using BIT() macros
- use u8 instead of unsigned char for byte data
- use input_set_capability() instead of manipulating capabilities bits
directly
- use sign_extend32() when extracting wheel data.
- do not abuse -1 as error code, propagate errors from various calls.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
- switch to using BIT() macros
- use u8 instead of unsigned char for byte data
- use input_set_capability() instead of manipulating capabilities bits
directly
- use sign_extend32() when extracting wheel data.
- do not abuse -1 as error code, propagate errors from various calls.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Many protocol driver re-implement code to parse buttons or motion data from
the standard PS/2 protocol. Let's split the parsing into separate
functions and reuse them in protocol drivers.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input layer updates from Dmitry Torokhov:
- evdev interface has been adjusted to extend the life of timestamps on
32 bit systems to the year of 2108
- Synaptics RMI4 driver's PS/2 guest handling ha beed updated to
improve chances of detecting trackpoints on the pass-through port
- mms114 touchcsreen controller driver has been updated to support
generic device properties and work with mms152 cntrollers
- Goodix driver now supports generic touchscreen properties
- couple of drivers for AVR32 architecture are gone as the architecture
support has been removed from the kernel
- gpio-tilt driver has been removed as there are no mainline users and
the driver itself is using legacy APIs and relies on platform data
- MODULE_LINECSE/MODULE_VERSION cleanups
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (45 commits)
Input: goodix - use generic touchscreen_properties
Input: mms114 - fix typo in definition
Input: mms114 - use BIT() macro instead of explicit shifting
Input: mms114 - replace mdelay with msleep
Input: mms114 - add support for mms152
Input: mms114 - drop platform data and use generic APIs
Input: mms114 - mark as direct input device
Input: mms114 - do not clobber interrupt trigger
Input: edt-ft5x06 - fix error handling for factory mode on non-M06
Input: stmfts - set IRQ_NOAUTOEN to the irq flag
Input: auo-pixcir-ts - delete an unnecessary return statement
Input: auo-pixcir-ts - remove custom log for a failed memory allocation
Input: da9052_tsi - remove unused mutex
Input: docs - use PROPERTY_ENTRY_U32() directly
Input: synaptics-rmi4 - log when we create a guest serio port
Input: synaptics-rmi4 - unmask F03 interrupts when port is opened
Input: synaptics-rmi4 - do not delete interrupt memory too early
Input: ad7877 - use managed resource allocations
Input: stmfts,s6sy671 - add SPDX identifier
Input: remove atmel-wm97xx touchscreen driver
...
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJabj6pAAoJEHm+PkMAQRiGs8cIAJQFkCWnbz86e3vG4DuWhyA8
CMGHCQdUOxxFGa/ixhIiuetbC0x+JVHAjV2FwVYbAQfaZB3pfw2iR1ncQxpAP1AI
oLU9vBEqTmwKMPc9CM5rRfnLFWpGcGwUNzgPdxD5yYqGDtcM8K840mF6NdkYe5AN
xU8rv1wlcFPF4A5pvHCH0pvVmK4VxlVFk/2H67TFdxBs4PyJOnSBnf+bcGWgsKO6
hC8XIVtcKCH2GfFxt5d0Vgc5QXJEpX1zn2mtCa1MwYRjN2plgYfD84ha0xE7J0B0
oqV/wnjKXDsmrgVpncr3txd4+zKJFNkdNRE4eLAIupHo2XHTG4HvDJ5dBY2NhGU=
=sOml
-----END PGP SIGNATURE-----
Merge tag 'v4.15' into next
Sync with mainline to get in trackpoint updates and other changes.
Pull input fixes from Dmitry Torokhov:
"The main item is that we try to better handle the newer trackpoints on
Lenovo devices that are now being produced by Elan/ALPS/NXP and only
implement a small subset of the original IBM trackpoint controls"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Revert "Input: synaptics_rmi4 - use devm_device_add_group() for attributes in F01"
Input: trackpoint - only expose supported controls for Elan, ALPS and NXP
Input: trackpoint - force 3 buttons if 0 button is reported
Input: xpad - add support for PDP Xbox One controllers
Input: stmfts,s6sy671 - add SPDX identifier
The newer trackpoints from ALPS, Elan and NXP implement a very limited
subset of extended commands and controls that the original trackpoints
implemented, so we should not be exposing not working controls in sysfs.
The newer trackpoints also do not implement "Power On Reset" or "Read
Extended Button Status", so we should not be using these commands during
initialization.
While we are at it, let's change "unsigned char" to u8 for byte data or
bool for booleans and use better suited error codes instead of -1.
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Lenovo introduced trackpoint compatible sticks with minimum PS/2 commands.
They supposed to reply with 0x02, 0x03, or 0x04 in response to the
"Read Extended ID" command, so we would know not to try certain extended
commands. Unfortunately even some trackpoints reporting the original IBM
version (0x01 firmware 0x0e) now respond with incorrect data to the "Get
Extended Buttons" command:
thinkpad_acpi: ThinkPad BIOS R0DET87W (1.87 ), EC unknown
thinkpad_acpi: Lenovo ThinkPad E470, model 20H1004SGE
psmouse serio2: trackpoint: IBM TrackPoint firmware: 0x0e, buttons: 0/0
Since there are no trackpoints without buttons, let's assume the trackpoint
has 3 buttons when we get 0 response to the extended buttons query.
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=196253
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input fixes from Dmitry Torokhov:
- a fix for use-after-free in Synaptics RMI4 driver
- correction to multitouch contact tracking on certain ALPS touchpads
(which got broken when we tried to fix the 2-finger scrolling)
- touchpad on Lenovo T640p is switched over to SMbus/RMI
- a few device node refcount fixes
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: synaptics-rmi4 - prevent UAF reported by KASAN
Input: ALPS - fix multi-touch decoding on SS4 plus touchpads
Input: synaptics - Lenovo Thinkpad T460p devices should use RMI
Input: of_touchscreen - add MODULE_LICENSE
Input: 88pm860x-ts - fix child-node lookup
Input: twl6040-vibra - fix child-node lookup
Input: twl4030-vibra - fix sibling-node lookup
The variable pwr_cmd is being assigned to cyapa->suspend_power_mode
twice, once during the declaration and once after taking an
interruptible mutex lock. Remove the redundant first assignment
since the value is never read and it is outside the mutex lock.
Cleans up clang warning:
drivers/input/mouse/cyapa.c:743:5: warning: Value stored to 'pwr_cmd'
during its initialization is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
MODULE_VERSION is useless for in-kernel drivers, so just remove all
usage of it in the elan_i2c mouse driver. Now that this is gone, the
ELAN_DRIVER_VERSION define was also removed as it was pointless.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
input_mt_init_slots() resets the ABS_X/Y fuzz to 0 and expects the driver
to call input_mt_report_pointer_emulation(). That is based on the MT
position bits which are already defuzzed - hence a fuzz of 0.
In the case of synaptics semi-mt devices, we report the ABS_X/Y axes
manually. This results in the MT position being defuzzed but the
single-touch emulation missing that defuzzing.
Work around this by re-initializing the ABS_X/Y axes after the MT axis to
get the same fuzz value back.
https://bugs.freedesktop.org/show_bug.cgi?id=104533
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When Synaptics protocol is disabled, we still need to try and detect the
hardware, so we can switch to SMBus device if SMbus is detected, or we know
that it is Synaptics device and reset it properly for the bare PS/2
protocol.
Fixes: c378b5119e ("Input: psmouse - factor out common protocol probing code")
Reported-by: Matteo Croce <mcroce@redhat.com>
Tested-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The fix for handling two-finger scroll (i4a646580f793 - "Input: ALPS -
fix two-finger scroll breakage in right side on ALPS touchpad")
introduced a minor "typo" that broke decoding of multi-touch events are
decoded on some ALPS touchpads. For example, tapping with three-fingers
can no longer be used to emulate middle-mouse-button (the kernel doesn't
recognize this as the proper event, and doesn't report it correctly to
userspace). This affects touchpads that use SS4 "plus" protocol
variant, like those found on Dell E7270 & E7470 laptops (tested on
E7270).
First, probably the code in alps_decode_ss4_v2() for case
SS4_PACKET_ID_MULTI used inconsistent indices to "f->mt[]". You can see
0 & 1 are used for the "if" part but 2 & 3 are used for the "else" part.
Second, in the previous patch, new macros were introduced to decode X
coordinates specific to the SS4 "plus" variant, but the macro to
define the maximum X value wasn't changed accordingly. The macros to
decode X values for "plus" variant are effectively shifted right by 1
bit, but the max wasn't shifted too. This causes the driver to
incorrectly handle "no data" cases, which also interfered with how
multi-touch was handled.
Fixes: 4a646580f7 ("Input: ALPS - fix two-finger scroll breakage...")
Signed-off-by: Nir Perry <nirperry@gmail.com>
Reviewed-by: Masaki Ota <masaki.ota@jp.alps.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The tpouchpad/trackpoint on Lenovo Thinkpad T460p work with smbus/RMI.
Signed-off-by: Zhenjie Wang <zhenjie.wang@sjtu.edu.cn>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input fixes from Dmitry Torokhov:
"Just a few driver fixups, nothing exciting"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: xen-kbdfront - do not advertise multi-touch pressure support
Input: hideep - fix compile error due to missing include file
Input: elants_i2c - do not clobber interrupt trigger on x86
Input: joystick/analog - riscv has get_cycles()
Input: elantech - add new icbody type 15
Input: ims-pcu - fix typo in the error message
The touchpad of Lenovo Thinkpad L480 reports it's version as 15.
Cc: stable@vger.kernel.org
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input updates from Dmitry Torokhov:
- three new touchscreen drivers: EETI EXC3000, HiDeep, and Samsung
S6SY761
- the timer API conversion (setup_timer() -> timer_setup())
- a few drivers swiytched to using managed API for creating custom
device attributes
- other assorted fixed and cleanups.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (50 commits)
Input: gamecon - mark expected switch fall-throughs
Input: sidewinder - mark expected switch fall-throughs
Input: spaceball - mark expected switch fall-throughs
Input: uinput - unlock on allocation failure in ioctl
Input: add support for the Samsung S6SY761 touchscreen
Input: add support for HiDeep touchscreen
Input: st1232 - remove obsolete platform device support
Input: convert autorepeat timer to use timer_setup()
media: ttpci: remove autorepeat handling and use timer_setup
Input: cyttsp4 - avoid overflows when calculating memory sizes
Input: mxs-lradc - remove redundant assignment to pointer input
Input: add I2C attached EETI EXC3000 multi touch driver
Input: goodix - support gt1151 touchpanel
Input: ps2-gpio - actually abort probe when connected to sleeping GPIOs
Input: hil_mlc - convert to using timer_setup()
Input: hp_sdc - convert to using timer_setup()
Input: touchsceen - convert timers to use timer_setup()
Input: keyboard - convert timers to use timer_setup()
Input: uinput - fold header into the driver proper
Input: uinput - remove uinput_allocate_device()
...
Pull x86 platform updates from Ingo Molnar:
"The main changes in this cycle were:
- a refactoring of the early virt init code by merging 'struct
x86_hyper' into 'struct x86_platform' and 'struct x86_init', which
allows simplifications and also the addition of a new
->guest_late_init() callback. (Juergen Gross)
- timer_setup() conversion of the UV code (Kees Cook)"
* 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/virt/xen: Use guest_late_init to detect Xen PVH guest
x86/virt, x86/platform: Add ->guest_late_init() callback to hypervisor_x86 structure
x86/virt, x86/acpi: Add test for ACPI_FADT_NO_VGA
x86/virt: Add enum for hypervisors to replace x86_hyper
x86/virt, x86/platform: Merge 'struct x86_hyper' into 'struct x86_platform' and 'struct x86_init'
x86/platform/UV: Convert timers to use timer_setup()
Pull input layer updates from Dmitry Torokhov:
- a new ACPI ID for Elan touchpad found in yet another Ideapad model
- Synaptics RMI4 will allow binding to controllers reporting SMB
version 3 (note that we are not adding any new ACPI IDs to the
Synaptics PS/2 drover so unless user explicitly enables intertouch
support there is no user-visible change)
- a fixup to TSC 2004/5 touchscreen driver to mark input devices as
"direct" to help userspace identify the type of device they are
dealing with
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: synaptics-rmi4 - RMI4 can also use SMBUS version 3
Input: tsc200x-core - set INPUT_PROP_DIRECT
Input: elan_i2c - add ELAN060C to the ACPI table
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJZ/30WAAoJEHm+PkMAQRiG1YkIAIVgcZS9SPzjcH+/NpcNJ4wv
Bp8xyfj/X6Eswn63ebrV/qij65Esmha7wnSREcFqrfNecRwOAdvYCjj20jqKGws2
p03sOS4aVSpJSQcqJ9sdF3Xx/P7CcK4IAjr0ihQbqozXiZAgVzTlYJwB+ErBMWFU
6NFYXg/Xp7FJXJ0o14yHpZ4RqgbLV95CgFIG9hzwvCibsW6ZBvGtYBD99IjeojPg
rw+B+Osck7XjC6IHqF/u760nTOaP8vVlTrCRqvFityGS9ZFQZDzEKYqxYgk8cVFC
jzR3fuHiWiomhyP9dLUZn6UuYQTaThhY58LvsEwV0JVJH9mUwcA4u5nO0wDUCO4=
=hhQa
-----END PGP SIGNATURE-----
Merge tag 'v4.14-rc8' into next
Merge with mainline to bring in SPDX markings to avoid annoying merge
problems when some header files get deleted.
ELAN060C touchpad uses elan_i2c as its driver. It can be
found on Lenovo ideapad 320-14AST.
BugLink: https://bugs.launchpad.net/bugs/1727544
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWfswbQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykvEwCfXU1MuYFQGgMdDmAZXEc+xFXZvqgAoKEcHDNA
6dVh26uchcEQLN/XqUDt
=x306
-----END PGP SIGNATURE-----
Merge tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull initial SPDX identifiers from Greg KH:
"License cleanup: add SPDX license identifiers to some files
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the
'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally
binding shorthand, which can be used instead of the full boiler plate
text.
This patch is based on work done by Thomas Gleixner and Kate Stewart
and Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset
of the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to
license had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied
to a file was done in a spreadsheet of side by side results from of
the output of two independent scanners (ScanCode & Windriver)
producing SPDX tag:value files created by Philippe Ombredanne.
Philippe prepared the base worksheet, and did an initial spot review
of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537
files assessed. Kate Stewart did a file by file comparison of the
scanner results in the spreadsheet to determine which SPDX license
identifier(s) to be applied to the file. She confirmed any
determination that was not immediately clear with lawyers working with
the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained
>5 lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that
was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that
became the concluded license(s).
- when there was disagreement between the two scanners (one detected
a license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply
(and which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases,
confirmation by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights.
The Windriver scanner is based on an older version of FOSSology in
part, so they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot
checks in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect
the correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial
patch version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch
license was not GPL-2.0 WITH Linux-syscall-note to ensure that the
applied SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
License cleanup: add SPDX license identifier to uapi header files with a license
License cleanup: add SPDX license identifier to uapi header files with no license
License cleanup: add SPDX GPL-2.0 license identifier to files with no license
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ELAN0611 touchpad uses elan_i2c as its driver. It can be found
on Lenovo ideapad 320-15IKB.
So add it to ACPI table to enable the touchpad.
[Ido Adiv <idoad123@gmail.com> reports that the same ACPI ID is used for
Elan touchpad in ideapad 520].
BugLink: https://bugs.launchpad.net/bugs/1723736
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJZ7clWAAoJEHm+PkMAQRiG07AH/iKcej+AsurISHx6i/LUEDC1
a9wo5HAR5kEj+ohdE3JSkD9BHLcyhcCXaqIk9yOrwi9xv1DrPv8U/nGkKzZJzFi2
mGWK09Zgi+vgSpA+YSErgl05IVGtgaryQQPqQdawpyRpqTUwP0+2pLnKEnJe0f05
fpv+S4bDKUCuE8GcVNjF9gxXDg8j60fFa+oAcn7QPS6dCun/H6TbDRue5oeky0Y+
50ZYjjioy9S9DIm2VF7pktMCP/mK/fgb+Q+4Up09VJGHGhq+891SRJ27yDulxo47
/gq22SRIGBX2PGNllSwhYslgaCRRlYTMBYOIWrBreanA4NpGD662dp+GgWhD154=
=TAMw
-----END PGP SIGNATURE-----
Merge tag 'v4.14-rc6' into next
Merge with mainline to bring in the timer API changes.
This makes the GPIO mouse probe nicely from the device tree if found in a
tree. As the driver uses device properties it can easily be amended to also
probe from ACPI devices.
Acked-by: Hans-Christian Noren Egtvedt <egtvedt@samfundet.no>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This converts the GPIO mouse to use descriptors and fwnode properties. The
polarity settings go out the window since GPIO descriptor already know
about polarity so this should be configured in device tree or ACPI or
similar.
Set scanning interval by default to 50ms if not found as a property on the
device.
Acked-by: Hans-Christian Noren Egtvedt <egtvedt@samfundet.no>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use more appropriate names for the "platform data" which is now just a
simple state container for the GPIO mouse.
Acked-by: Hans-Christian Noren Egtvedt <egtvedt@samfundet.no>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This is not used much: git grep gpio_mouse_platform_data shows
that absolutely nothing in the kernel defines this platform
data.
It could be argued that the driver should be deleted. But that
is a bit harsh I think since it seems generally useful. So
this patch starts a series which repurposes it to be used with
hardware nodes from device tree or ACPI.
This first patch simply localize the platform data header and
allocates a dummy platform data.
Yes: this patch leaves the driver in a pretty useless state,
but since nothing is instantiating this driver, it doesn't
make it more useless than it already is. Later patches makes
use of the driver.
Acked-by: Hans-Christian Noren Egtvedt <egtvedt@samfundet.no>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In certain situations kernel tracking seems to be getting confused
and incorrectly reporting the slot of a contact. On example is when
the user does a three finger click or tap and then places two fingers
on the touchpad in the same area. The kernel tracking code seems to
continue to think that there are three contacts on the touchpad and
incorrectly alternates the slot of one of the contacts. The result that
is the input subsystem reports a stream of button press and release
events as the reported slot changes.
Kernel tracking was originally enabled to prevent cursor jumps, but it
is unclear how much of an issue kernel jumps actually are. This patch
simply disabled kernel tracking for now.
Fixes: https://bugzilla.redhat.com/show_bug.cgi?id=1482640
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Tested-by: Kamil Páral <kparal@redhat.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
On x86 we historically used falling edge interrupts in the driver
because that's how first Chrome devices were configured. They also
did not use ACPI to enumerate I2C devices (because back then there
was no kernel support for that), so trigger was hard-coded in the
driver. However the controller behavior is much more reliable if
we use level triggers, and that is how we configured ARM devices,
and how want to configure newer x86 devices as well. All newer
x86 boxes have their I2C devices enumerated in ACPI.
Let's see if platform code (ACPI, DT) described interrupt and
specified particular trigger type, and if so, let's use it instead
of always clobbering trigger with IRQF_TRIGGER_FALLING. We will
still use this trigger type as a fallback if platform code left
interrupt trigger unconfigured.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=196761
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The original 20ms delay is only marginally enough delay after a block write
operation during firmware update. Let's increase the delay to ensure that
the controller finishes up storing the page to avoid failures in the
firmware updates.
Signed-off-by: KT Liao <kt.liao@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-----BEGIN PGP SIGNATURE-----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=nb+l
-----END PGP SIGNATURE-----
Merge tag 'ib-mfd-many-v4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd into next
Merge "Immutable branch between MFD and many other subsystems due for
the v4.14 merge window" to get the TWL headers moved to the right place.
