Add the four SPI masters on each CFAM. Each master has four 128KB EEPROM
devices attached to it.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Adding pca9552 exposes the presence detect lines for the cards and
tca9554 exposes the presence details for the cards.
Signed-off-by: Jet Li <Jet.Li@ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Initial introduction of AMD EthanolX platform equipped with an
Aspeed ast2500 BMC manufactured by AMD.
AMD EthanolX platform is an AMD customer reference board with an
Aspeed ast2500 BMC manufactured by AMD.
This adds AMD EthanolX device tree file including the flash layout
used by EthanolX BMC machines.
Signed-off-by: Supreeth Venkatesh <supreeth.venkatesh@amd.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
We have a 4-bus mux whose output is selected by two GPIO inputs. Wire it
up in the devicetree and ensure the output is enabled by hogging the
appropriate line.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Enable pwm_tacho device for fan control and monitoring in Wedge40.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Enable ADC controller and corresponding voltage sensoring channels for
Wedge40.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Disable i2c bus #9, #10 and #13 as these i2c controllers are not used on
Wedge40.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Create all the i2c switches in device tree and use aliases to assign
child channels with consistent bus numbers.
Besides, "i2c-mux-idle-disconnect" is set for all the i2c switches to
avoid potential conflicts when multiple devices (beind the switches)
use the same device address.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
The GPIO on Q0 is used for resetting the CFAM of the processor that the
ASPEED master is connected to.
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
The GPIO on Q0 is used for resetting the CFAM of the processor that the
ASPEED master is connected to.
The signal is wired as active high on the first pass systems.
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
GPIOP7 is used in the Rainier design to manage the state of a
microcontroller elsewhere in the system but its ball, Y23, is the
driver of the heartbeat LED on the ast2600-evb and the SoC defaults Y23
at power-on to the pulse-train behaviour used to drive the LED. This
causes much confusion for the micro in the Rainier system, so hog the
line as early as possible.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
The hub FSI master can access the cfams on two other processors. Reflect
this by adding a second cfam to the first hub description.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Tested-by: Andrew Geissler <geissonator@yahoo.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Rainier uses GPIO B6 as the checkstop GPIO. Define the line-name
so that this GPIO can be found by name.
Signed-off-by: Ben Tyner <ben.tyner@ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
The attention handler will monitor the checkstop gpio via the character
device interface so it needs to not be defined.
Signed-off-by: Ben Tyner <ben.tyner@ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Add a reserved memory node for the VGA memory. Add the XDMA engine node,
enable it, and point it's memory region to the VGA memory.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Add a reserved memory node for the VGA memory. Add the XDMA engine node,
enable it, and point it's memory region to the VGA memory.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Add the PCI-E root complex reset, correct the pcie-device property, and
add the Aspeed SCU interrupt controller include.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Correct the pcie-device property, and add the Aspeed SCU interrupt
controller include.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Set smbus_en of IO expander to 1 in order to be able to read sensor.
Signed-off-by: Ben Pai <Ben_Pai@wistron.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
- fix build rules in binderfs sample
- fix build errors when Kbuild recurses to the top Makefile
- covert '---help---' in Kconfig to 'help'
-----BEGIN PGP SIGNATURE-----
iQJJBAABCgAzFiEEbmPs18K1szRHjPqEPYsBB53g2wYFAl7lBuYVHG1hc2FoaXJv
eUBrZXJuZWwub3JnAAoJED2LAQed4NsGHvIP/3iErjPshpg/phwH8NTCS4SFkiti
BZRM+2lupSn7Qs53BTpVzIkXoHBJQZlJxlQ5HY8ScO+fiz28rKZr+b40us+je1Q+
SkvSPfwZzxjEg7lAZutznG4KgItJLWJKmDyh9T8Y8TAuG4f8WO0hKnXoAp3YorS2
zppEIxso8O5spZPjp+fF/fPbxPjIsabGK7Jp2LpSVFR5pVDHI/ycTlKQS+MFpMEx
6JIpdFRw7TkvKew1dr5uAWT5btWHatEqjSR3JeyVHv3EICTGQwHmcHK67cJzGInK
T51+DT7/CpKtmRgGMiTEu/INfMzzoQAKl6Fcu+vMaShTN97Hk9DpdtQyvA6P/h3L
8GA4UBct05J7fjjIB7iUD+GYQ0EZbaFujzRXLYk+dQqEJRbhcCwvdzggGp0WvGRs
1f8/AIpgnQv8JSL/bOMgGMS5uL2dSLsgbzTdr6RzWf1jlYdI1i4u7AZ/nBrwWP+Z
iOBkKsVceEoJrTbaynl3eoYqFLtWyDau+//oBc2gUvmhn8ioM5dfqBRiJjxJnPG9
/giRj6xRIqMMEw8Gg8PCG7WebfWxWyaIQwlWBbPok7DwISURK5mvOyakZL+Q25/y
6MBr2H8NEJsf35q0GTINpfZnot7NX4JXrrndJH8NIRC7HEhwd29S041xlQJdP0rs
E76xsOr3hrAmBu4P
=1NIT
-----END PGP SIGNATURE-----
Merge tag 'kbuild-v5.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull more Kbuild updates from Masahiro Yamada:
- fix build rules in binderfs sample
- fix build errors when Kbuild recurses to the top Makefile
- covert '---help---' in Kconfig to 'help'
* tag 'kbuild-v5.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
treewide: replace '---help---' in Kconfig files with 'help'
kbuild: fix broken builds because of GZIP,BZIP2,LZOP variables
samples: binderfs: really compile this sample and fix build issues
EFI on ARM only supports short descriptors, and given that it mandates
that the MMU and caches are on, it is implied that booting in HYP mode
is not supported.
However, implementations of EFI exist (i.e., U-Boot) that ignore this
requirement, which is not entirely unreasonable, given that it makes
HYP mode inaccessible to the operating system.
So let's make sure that we can deal with this condition gracefully.
We already tolerate booting the EFI stub with the caches off (even
though this violates the EFI spec as well), and so we should deal
with HYP mode boot with MMU and caches either on or off.
- When the MMU and caches are on, we can ignore the HYP stub altogether,
since we can carry on executing at HYP. We do need to ensure that we
disable the MMU at HYP before entering the kernel proper.
- When the MMU and caches are off, we have to drop to SVC mode so that
we can set up the page tables using short descriptors. In this case,
we need to install the HYP stub as usual, so that we can return to HYP
mode before handing over to the kernel proper.
Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Redefine GZIP, BZIP2, LZOP variables as KGZIP, KBZIP2, KLZOP resp.
GZIP, BZIP2, LZOP env variables are reserved by the tools. The original
attempt to redefine them internally doesn't work in makefiles/scripts
intercall scenarios, e.g., "make GZIP=gzip bindeb-pkg" and results in
broken builds. There can be other broken build commands because of this,
so the universal solution is to use non-reserved env variables for the
compression tools.
Fixes: 8dfb61dcba ("kbuild: add variables for compression tools")
Signed-off-by: Denis Efremov <efremov@linux.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Here are the large set of USB and PHY driver updates for 5.8-rc1.
Nothing huge, just lots of little things:
- USB gadget fixes and additions all over the place
- new PHY drivers
- PHY driver fixes and updates
- XHCI driver updates
- musb driver updates
- more USB-serial driver ids added
- various USB quirks added
- thunderbolt minor updates and fixes
- typec updates and additions
Full details are in the shortlog.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXtzqVA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynftwCfeanyI6TR5AdfJVZN50B6/ySvVwcAn07i9VRX
tnt2kz0UqReYpLt0wyJ7
=YP7o
-----END PGP SIGNATURE-----
Merge tag 'usb-5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY driver updates from Greg KH:
"Here are the large set of USB and PHY driver updates for 5.8-rc1.
Nothing huge, just lots of little things:
- USB gadget fixes and additions all over the place
- new PHY drivers
- PHY driver fixes and updates
- XHCI driver updates
- musb driver updates
- more USB-serial driver ids added
- various USB quirks added
- thunderbolt minor updates and fixes
- typec updates and additions
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (245 commits)
usb: dwc3: meson-g12a: fix USB2 PHY initialization on G12A and A1 SoCs
usb: dwc3: meson-g12a: fix error path when fetching the reset line fails
Revert "dt-bindings: usb: qcom,dwc3: Convert USB DWC3 bindings"
Revert "dt-bindings: usb: qcom,dwc3: Add compatible for SC7180"
Revert "dt-bindings: usb: qcom,dwc3: Introduce interconnect properties for Qualcomm DWC3 driver"
USB: serial: ch341: fix lockup of devices with limited prescaler
USB: serial: ch341: add basis for quirk detection
CDC-ACM: heed quirk also in error handling
USB: serial: option: add Telit LE910C1-EUX compositions
usb: musb: Fix runtime PM imbalance on error
usb: musb: jz4740: Prevent lockup when CONFIG_SMP is set
usb: musb: mediatek: add reset FADDR to zero in reset interrupt handle
usb: musb: use true for 'use_dma'
usb: musb: start session in resume for host port
usb: musb: return -ESHUTDOWN in urb when three-strikes error happened
USB: serial: qcserial: add DW5816e QDL support
thunderbolt: Add trivial .shutdown
usb: dwc3: keystone: Turn on USB3 PHY before controller
dt-bindings: usb: ti,keystone-dwc3.yaml: Add USB3.0 PHY property
dt-bindings: usb: convert keystone-usb.txt to YAML
...
- fix warnings in 'make clean' for ARCH=um, hexagon, h8300, unicore32
- ensure to rebuild all objects when the compiler is upgraded
- exclude system headers from dependency tracking and fixdep processing
- fix potential bit-size mismatch between the kernel and BPF user-mode
helper
- add the new syntax 'userprogs' to build user-space programs for the
target architecture (the same arch as the kernel)
- compile user-space sample code under samples/ for the target arch
instead of the host arch
- make headers_install fail if a CONFIG option is leaked to user-space
- sanitize the output format of scripts/checkstack.pl
- handle ARM 'push' instruction in scripts/checkstack.pl
- error out before modpost if a module name conflict is found
- error out when multiple directories are passed to M= because this
feature is broken for a long time
- add CONFIG_DEBUG_INFO_COMPRESSED to support compressed debug info
- a lot of cleanups of modpost
- dump vmlinux symbols out into vmlinux.symvers, and reuse it in the
second pass of modpost
- do not run the second pass of modpost if nothing in modules is updated
- install modules.builtin(.modinfo) by 'make install' as well as by
'make modules_install' because it is useful even when CONFIG_MODULES=n
- add new command line variables, GZIP, BZIP2, LZOP, LZMA, LZ4, and XZ
to allow users to use alternatives such as pigz, pbzip2, etc.
-----BEGIN PGP SIGNATURE-----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=GKe5
-----END PGP SIGNATURE-----
Merge tag 'kbuild-v5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild updates from Masahiro Yamada:
- fix warnings in 'make clean' for ARCH=um, hexagon, h8300, unicore32
- ensure to rebuild all objects when the compiler is upgraded
- exclude system headers from dependency tracking and fixdep processing
- fix potential bit-size mismatch between the kernel and BPF user-mode
helper
- add the new syntax 'userprogs' to build user-space programs for the
target architecture (the same arch as the kernel)
- compile user-space sample code under samples/ for the target arch
instead of the host arch
- make headers_install fail if a CONFIG option is leaked to user-space
- sanitize the output format of scripts/checkstack.pl
- handle ARM 'push' instruction in scripts/checkstack.pl
- error out before modpost if a module name conflict is found
- error out when multiple directories are passed to M= because this
feature is broken for a long time
- add CONFIG_DEBUG_INFO_COMPRESSED to support compressed debug info
- a lot of cleanups of modpost
- dump vmlinux symbols out into vmlinux.symvers, and reuse it in the
second pass of modpost
- do not run the second pass of modpost if nothing in modules is
updated
- install modules.builtin(.modinfo) by 'make install' as well as by
'make modules_install' because it is useful even when
CONFIG_MODULES=n
- add new command line variables, GZIP, BZIP2, LZOP, LZMA, LZ4, and XZ
to allow users to use alternatives such as pigz, pbzip2, etc.
* tag 'kbuild-v5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (96 commits)
kbuild: add variables for compression tools
Makefile: install modules.builtin even if CONFIG_MODULES=n
mksysmap: Fix the mismatch of '.L' symbols in System.map
kbuild: doc: rename LDFLAGS to KBUILD_LDFLAGS
modpost: change elf_info->size to size_t
modpost: remove is_vmlinux() helper
modpost: strip .o from modname before calling new_module()
modpost: set have_vmlinux in new_module()
modpost: remove mod->skip struct member
modpost: add mod->is_vmlinux struct member
modpost: remove is_vmlinux() call in check_for_{gpl_usage,unused}()
modpost: remove mod->is_dot_o struct member
modpost: move -d option in scripts/Makefile.modpost
modpost: remove -s option
modpost: remove get_next_text() and make {grab,release_}file static
modpost: use read_text_file() and get_line() for reading text files
modpost: avoid false-positive file open error
modpost: fix potential mmap'ed file overrun in get_src_version()
modpost: add read_text_file() and get_line() helpers
modpost: do not call get_modinfo() for vmlinux(.o)
...
Allow user to use alternative implementations of compression tools,
such as pigz, pbzip2, pxz. For example, multi-threaded tools to
speed up the build:
$ make GZIP=pigz BZIP2=pbzip2
Variables _GZIP, _BZIP2, _LZOP are used internally because original env
vars are reserved by the tools. The use of GZIP in gzip tool is obsolete
since 2015. However, alternative implementations (e.g., pigz) still rely
on it. BZIP2, BZIP, LZOP vars are not obsolescent.
The credit goes to @grsecurity.
As a sidenote, for multi-threaded lzma, xz compression one can use:
$ export XZ_OPT="--threads=0"
Signed-off-by: Denis Efremov <efremov@linux.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
This is the set of device tree changes, mostly covering new
hardware support, with 577 patches touching a little over 500
files.
There are five new Arm SoCs supported in this release, all of
them for existing SoC families:
- Realtek RTD1195, RTD1395 and RTD1619 -- three SoCs used in
both NAS devices and Android Set-top-box designs, along
with the "Horseradish", "Lion Skin" and "Mjolnir" reference
platforms; the Mele X1000 and Xnano X5 set-top-boxes and
the Banana Pi BPi-M4 single-board computer.
- Renesas RZ/G1H (r8a7742) -- a high-end 32-bit industrial SoC
and the iW-RainboW-G21D-Qseven-RZG1H board/SoM
- Rockchips RK3326 -- low-end 64-bit SoC along with the
Odroid-GO Advance game console
Newly added machines on already supported SoCs are:
- AMLogic S905D based Smartlabs SML-5442TW TV box
- AMLogic S905X3 based ODROID-C4 SBC
- AMLogic S922XH based Beelink GT-King Pro TV box
- Allwinner A20 based Olimex A20-OLinuXino-LIME-eMMC SBC
- Aspeed ast2500 based BMCs in Facebook x86 "Yosemite V2"
and YADRO OpenPower P9 "Nicole"
- Marvell Kirkwood based Check Point L-50 router
- Mediatek MT8173 based Elm/Hana Chromebook laptops
- Microchip SAMA5D2 "Industrial Connectivity Platform"
reference board
- NXP i.MX8m based Beacon i.MX8m-Mini SoM development kit
- Octavo OSDMP15x based Linux Automation MC-1 development board
- Qualcomm SDM630 based Xiaomi Redmi Note 7 phone
- Realtek RTD1295 based Xnano X5 TV Box
- STMicroelectronics STM32MP1 based Stinger96 single-board
computer and IoT Box
- Samsung Exynos4210 based based Samsung Galaxy S2 phone
- Socionext Uniphier based Akebi96 SBC
- TI Keystone based K2G Evaluation board
- TI am5729 based Beaglebone-AI development board
Include device descriptions for additional hardware support in existing
SoCs and machines based on all major SoC platforms:
- AMlogic Meson
- Allwinner sunxi
- Arm Juno/VFP/Vexpress/Integrator
- Broadcom bcm283x/bcm2711
- Hisilicon hi6220
- Marvell EBU
- Mediatek MT27xx, MT76xx, MT81xx and MT67xx
- Microchip SAMA5D2
- NXP i.MX6/i.MX7/i.MX8 and Layerscape
- Nvidia Tegra
- Qualcomm Snapdragon
- Renesas r8a77961, r8a7791
- Rockchips RK32xx/RK33xx
- ST-Ericsson ux500
- STMicroelectronics SMT32
- Samsung Exynos and S5PV210
- Socionext Uniphier
- TI OMAP5/DRA7 and Keystone
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=17kt
-----END PGP SIGNATURE-----
Merge tag 'arm-dt-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM devicetree updates from Arnd Bergmann:
"This is the set of device tree changes, mostly covering new hardware
support, with 577 patches touching a little over 500 files.
There are five new Arm SoCs supported in this release, all of them for
existing SoC families:
- Realtek RTD1195, RTD1395 and RTD1619 -- three SoCs used in both NAS
devices and Android Set-top-box designs, along with the
"Horseradish", "Lion Skin" and "Mjolnir" reference platforms; the
Mele X1000 and Xnano X5 set-top-boxes and the Banana Pi BPi-M4
single-board computer.
- Renesas RZ/G1H (r8a7742) -- a high-end 32-bit industrial SoC and
the iW-RainboW-G21D-Qseven-RZG1H board/SoM
- Rockchips RK3326 -- low-end 64-bit SoC along with the Odroid-GO
Advance game console
Newly added machines on already supported SoCs are:
- AMLogic S905D based Smartlabs SML-5442TW TV box
- AMLogic S905X3 based ODROID-C4 SBC
- AMLogic S922XH based Beelink GT-King Pro TV box
- Allwinner A20 based Olimex A20-OLinuXino-LIME-eMMC SBC
- Aspeed ast2500 based BMCs in Facebook x86 "Yosemite V2" and YADRO
OpenPower P9 "Nicole"
- Marvell Kirkwood based Check Point L-50 router
- Mediatek MT8173 based Elm/Hana Chromebook laptops
- Microchip SAMA5D2 "Industrial Connectivity Platform" reference
board
- NXP i.MX8m based Beacon i.MX8m-Mini SoM development kit
- Octavo OSDMP15x based Linux Automation MC-1 development board
- Qualcomm SDM630 based Xiaomi Redmi Note 7 phone
- Realtek RTD1295 based Xnano X5 TV Box
- STMicroelectronics STM32MP1 based Stinger96 single-board computer
and IoT Box
- Samsung Exynos4210 based based Samsung Galaxy S2 phone
- Socionext Uniphier based Akebi96 SBC
- TI Keystone based K2G Evaluation board
- TI am5729 based Beaglebone-AI development board
Include device descriptions for additional hardware support in
existing SoCs and machines based on all major SoC platforms:
- AMlogic Meson
- Allwinner sunxi
- Arm Juno/VFP/Vexpress/Integrator
- Broadcom bcm283x/bcm2711
- Hisilicon hi6220
- Marvell EBU
- Mediatek MT27xx, MT76xx, MT81xx and MT67xx
- Microchip SAMA5D2
- NXP i.MX6/i.MX7/i.MX8 and Layerscape
- Nvidia Tegra
- Qualcomm Snapdragon
- Renesas r8a77961, r8a7791
- Rockchips RK32xx/RK33xx
- ST-Ericsson ux500
- STMicroelectronics SMT32
- Samsung Exynos and S5PV210
- Socionext Uniphier
- TI OMAP5/DRA7 and Keystone"
* tag 'arm-dt-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (564 commits)
ARM: dts: keystone: Rename "msmram" node to "sram"
arm: dts: mt2712: add uart APDMA to device tree
arm64: dts: mt8183: add mmc node
arm64: dts: mt2712: add ethernet device node
arm64: tegra: Make the RTC a wakeup source on Jetson Nano and TX1
ARM: dts: mmp3: Add the fifth SD HCI
ARM: dts: berlin*: Fix up the SDHCI node names
ARM: dts: mmp3: Fix USB & USB PHY node names
ARM: dts: mmp3: Fix L2 cache controller node name
ARM: dts: mmp*: Fix up encoding of the /rtc interrupts property
ARM: dts: pxa*: Fix up encoding of the /rtc interrupts property
ARM: dts: pxa910: Fix the gpio interrupt cell number
ARM: dts: pxa3xx: Fix up encoding of the /gpio interrupts property
ARM: dts: pxa168: Fix the gpio interrupt cell number
ARM: dts: pxa168: Add missing address/size cells to i2c nodes
ARM: dts: dove: Fix interrupt controller node name
ARM: dts: kirkwood: Fix interrupt controller node name
arm64: dts: Add SC9863A emmc and sd card nodes
arm64: dts: Add SC9863A clock nodes
arm64: dts: mt6358: add PMIC MT6358 related nodes
...
One new platform gets added, the Realtek RTD1195, which is an older
Cortex-a7 based relative of the RTD12xx chips that are already supported
in arch/arm64. The platform may also be extended to support running
32-bit kernels on those 64-bit chips for memory-constrained machines.
In the Renesas shmobile platform, we gain support for "RZ/G1H" or R8A7742,
an eight-core chip based on Cortex-A15 and Cortex-A7 cores, originally
released in 2016 as one of the last high-end 32-bit designs.
There is ongoing cleanup for the integrator, tegra, imx, and omap2
platforms, with integrator getting very close to the goal of having
zero code in arch/arm/, and omap2 moving more of the chip specifics
from old board code into device tree files.
The Versatile Express platform is made more modular, with built-in
drivers now becoming loadable modules. This is part of a greater effort
for the Android OS to have a common kernel binary for all platforms and
any platform specific code in loadable modules.
The PXA platform drops support for Compulab's pxa2xx boards that had
rather unusual flash and PCI drivers but no known users remaining.
All device drivers specific to those boards can now get removed as
well.
Across platforms, there is ongoing cleanup, with Geert and Rob
revisiting some a lot of Kconfig options.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=gzCp
-----END PGP SIGNATURE-----
Merge tag 'arm-soc-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC updates from Arnd Bergmann:
"One new platform gets added, the Realtek RTD1195, which is an older
Cortex-a7 based relative of the RTD12xx chips that are already
supported in arch/arm64. The platform may also be extended to support
running 32-bit kernels on those 64-bit chips for memory-constrained
machines.
In the Renesas shmobile platform, we gain support for "RZ/G1H" or
R8A7742, an eight-core chip based on Cortex-A15 and Cortex-A7 cores,
originally released in 2016 as one of the last high-end 32-bit
designs.
There is ongoing cleanup for the integrator, tegra, imx, and omap2
platforms, with integrator getting very close to the goal of having
zero code in arch/arm/, and omap2 moving more of the chip specifics
from old board code into device tree files.
The Versatile Express platform is made more modular, with built-in
drivers now becoming loadable modules. This is part of a greater
effort for the Android OS to have a common kernel binary for all
platforms and any platform specific code in loadable modules.
The PXA platform drops support for Compulab's pxa2xx boards that had
rather unusual flash and PCI drivers but no known users remaining. All
device drivers specific to those boards can now get removed as well.
Across platforms, there is ongoing cleanup, with Geert and Rob
revisiting some a lot of Kconfig options"
* tag 'arm-soc-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (94 commits)
ARM: omap2: fix omap5_realtime_timer_init definition
ARM: zynq: Don't select CONFIG_ICST
ARM: OMAP2+: Fix regression for using local timer on non-SMP SoCs
clk: versatile: Fix kconfig dependency on COMMON_CLK_VERSATILE
ARM: davinci: fix build failure without I2C
power: reset: vexpress: fix build issue
power: vexpress: cleanup: use builtin_platform_driver
power: vexpress: add suppress_bind_attrs to true
Revert "ARM: vexpress: Don't select VEXPRESS_CONFIG"
MAINTAINERS: pxa: remove Compulab arm/pxa support
ARM: pxa: remove Compulab pxa2xx boards
bus: arm-integrator-lm: Fix return value check in integrator_ap_lm_probe()
soc: imx: move cpu code to drivers/soc/imx
ARM: imx: move cpu definitions into a header
ARM: imx: use device_initcall for imx_soc_device_init
ARM: imx: pcm037: make pcm970_sja1000_platform_data static
bus: ti-sysc: Timers no longer need legacy quirk handling
ARM: OMAP2+: Drop old timer code for dmtimer and 32k counter
ARM: dts: Configure system timers for omap2
ARM: dts: Configure system timers for ti81xx
...
Pull networking updates from David Miller:
1) Allow setting bluetooth L2CAP modes via socket option, from Luiz
Augusto von Dentz.
2) Add GSO partial support to igc, from Sasha Neftin.
3) Several cleanups and improvements to r8169 from Heiner Kallweit.
4) Add IF_OPER_TESTING link state and use it when ethtool triggers a
device self-test. From Andrew Lunn.
5) Start moving away from custom driver versions, use the globally
defined kernel version instead, from Leon Romanovsky.
6) Support GRO vis gro_cells in DSA layer, from Alexander Lobakin.
7) Allow hard IRQ deferral during NAPI, from Eric Dumazet.
8) Add sriov and vf support to hinic, from Luo bin.
9) Support Media Redundancy Protocol (MRP) in the bridging code, from
Horatiu Vultur.
10) Support netmap in the nft_nat code, from Pablo Neira Ayuso.
11) Allow UDPv6 encapsulation of ESP in the ipsec code, from Sabrina
Dubroca. Also add ipv6 support for espintcp.
12) Lots of ReST conversions of the networking documentation, from Mauro
Carvalho Chehab.
13) Support configuration of ethtool rxnfc flows in bcmgenet driver,
from Doug Berger.
14) Allow to dump cgroup id and filter by it in inet_diag code, from
Dmitry Yakunin.
15) Add infrastructure to export netlink attribute policies to
userspace, from Johannes Berg.
16) Several optimizations to sch_fq scheduler, from Eric Dumazet.
17) Fallback to the default qdisc if qdisc init fails because otherwise
a packet scheduler init failure will make a device inoperative. From
Jesper Dangaard Brouer.
18) Several RISCV bpf jit optimizations, from Luke Nelson.
19) Correct the return type of the ->ndo_start_xmit() method in several
drivers, it's netdev_tx_t but many drivers were using
'int'. From Yunjian Wang.
20) Add an ethtool interface for PHY master/slave config, from Oleksij
Rempel.
21) Add BPF iterators, from Yonghang Song.
22) Add cable test infrastructure, including ethool interfaces, from
Andrew Lunn. Marvell PHY driver is the first to support this
facility.
23) Remove zero-length arrays all over, from Gustavo A. R. Silva.
24) Calculate and maintain an explicit frame size in XDP, from Jesper
Dangaard Brouer.
25) Add CAP_BPF, from Alexei Starovoitov.
26) Support terse dumps in the packet scheduler, from Vlad Buslov.
27) Support XDP_TX bulking in dpaa2 driver, from Ioana Ciornei.
28) Add devm_register_netdev(), from Bartosz Golaszewski.
29) Minimize qdisc resets, from Cong Wang.
30) Get rid of kernel_getsockopt and kernel_setsockopt in order to
eliminate set_fs/get_fs calls. From Christoph Hellwig.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2517 commits)
selftests: net: ip_defrag: ignore EPERM
net_failover: fixed rollback in net_failover_open()
Revert "tipc: Fix potential tipc_aead refcnt leak in tipc_crypto_rcv"
Revert "tipc: Fix potential tipc_node refcnt leak in tipc_rcv"
vmxnet3: allow rx flow hash ops only when rss is enabled
hinic: add set_channels ethtool_ops support
selftests/bpf: Add a default $(CXX) value
tools/bpf: Don't use $(COMPILE.c)
bpf, selftests: Use bpf_probe_read_kernel
s390/bpf: Use bcr 0,%0 as tail call nop filler
s390/bpf: Maintain 8-byte stack alignment
selftests/bpf: Fix verifier test
selftests/bpf: Fix sample_cnt shared between two threads
bpf, selftests: Adapt cls_redirect to call csum_level helper
bpf: Add csum_level helper for fixing up csum levels
bpf: Fix up bpf_skb_adjust_room helper's skb csum setting
sfc: add missing annotation for efx_ef10_try_update_nic_stats_vf()
crypto/chtls: IPv6 support for inline TLS
Crypto/chcr: Fixes a coccinile check error
Crypto/chcr: Fixes compilations warnings
...
- Not a single new clocksource or clockevent driver!
- Device tree updates for various chips
- Fixes and improvements and cleanups all over the place
-----BEGIN PGP SIGNATURE-----
iQJGBAABCgAxFiEEQp8+kY+LLUocC4bMphj1TA10mKEFAl7WEEkTHHRnbHhAbGlu
dXRyb25peC5kZQAKCRCmGPVMDXSYoZxrD/dy2y712euXcZLgclXXQYLDnlRyqLN2
t/6XMeoVulah8UAHccCL+RjLLDHp2pJl1yGPe730GJe9Jxv9+ZVUtXak0VoIoQbO
HpNdNLD/Clq2jv1mgoXh1gb5xnEkQsAWcIFAyH4frB+mWZaOhpwqf51JT6QuwnPf
OAq09gGdRogslXKuliEuRgbHL/a6WjC5IG4gzzB/coxYPnjGpBc8eYY+QbISqALD
D84KJaNu/rOTwh8fXawBmFz5GwSk6LiGkh+Br/vSodYh3T23SWjVPJRsNX0UVT/S
m1tEx2njKBBzmyYjrCU2tF0cwdJ0AduARrCFPB11nrsldp4E36fuoRjs+bW5HZAO
JDajzHrPunYMN3pmh/D5Qk4/4v4XpPFluybqaoBIAee9L/8ulNKUMrEmjJHbHe+N
5pSmkUsxciRmRRyjfMK3xD8K1/P/J+dJnCY3qOEbDZ7O4nei7wdemY9awCIRdVWb
vJYWZwkbGFEsicEUjGgBSqesWuSg+pJRC896PQboonarZ4DZFEZ3B7sODNIrzb82
78nhJ/IGYNuJ4eL7yrxmNDllCOava4vwV87tedbWgAtguE4sDLljKb/V3abwOAOt
ZcNvZLCkMiXKdKKEbVJu/WRtQ+lvO1HNM4yB6S6I4R3kegWZu3zqsUL/xzDhk7O5
lrj0DKbKzUqn
=FFm0
-----END PGP SIGNATURE-----
Merge tag 'timers-core-2020-06-02' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer updates from Thomas Gleixner:
"The truly boring timer and clocksource updates for 5.8:
- Not a single new clocksource or clockevent driver!
- Device tree updates for various chips
- Fixes and improvements and cleanups all over the place"
* tag 'timers-core-2020-06-02' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (27 commits)
dt-bindings: timer: Add renesas,em-sti bindings
clocksource/drivers/timer-versatile: Clear OF_POPULATED flag
clocksource: mips-gic-timer: Mark GIC timer as unstable if ref clock changes
clocksource: mips-gic-timer: Register as sched_clock
clocksource: dw_apb_timer_of: Fix missing clockevent timers
clocksource: dw_apb_timer: Affiliate of-based timer with any CPU
clocksource: dw_apb_timer: Make CPU-affiliation being optional
dt-bindings: timer: Move snps,dw-apb-timer DT schema from rtc
dt-bindings: rtc: Convert snps,dw-apb-timer to DT schema
clocksource/drivers/timer-ti-dm: Do one override clock parent in prepare()
clocksource/drivers/timer-ti-dm: Fix spelling mistake "detectt" -> "detect"
clocksource/drivers/timer-ti-dm: Fix warning for set but not used
clocksource/drivers/timer-ti-dm: Add clockevent and clocksource support
clocksource/drivers/timer-ti-32k: Add support for initializing directly
drivers/clocksource/arm_arch_timer: Remove duplicate error message
clocksource/drivers/arc_timer: Remove duplicate error message
clocksource/drivers/rda: drop redundant Kconfig dependency
clocksource/drivers/timer-ti-dm: Fix warning for set but not used
clocksource/drivers/timer-ti-dm: Add clockevent and clocksource support
clocksource/drivers/timer-ti-32k: Add support for initializing directly
...
- remove a now unnecessary usage of the KERNEL_DS for
sys_oabi_epoll_ctl()
- update my email address in a number of drivers
- decompressor EFI updates from Ard Biesheuvel
- module unwind section handling updates
- sparsemem Kconfig cleanups
- make act_mm macro respect THREAD_SIZE
-----BEGIN PGP SIGNATURE-----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=vMHE
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm
Pull ARM updates from Russell King:
- remove a now unnecessary usage of the KERNEL_DS for
sys_oabi_epoll_ctl()
- update my email address in a number of drivers
- decompressor EFI updates from Ard Biesheuvel
- module unwind section handling updates
- sparsemem Kconfig cleanups
- make act_mm macro respect THREAD_SIZE
* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 8980/1: Allow either FLATMEM or SPARSEMEM on the multiplatform build
ARM: 8979/1: Remove redundant ARCH_SPARSEMEM_DEFAULT setting
ARM: 8978/1: mm: make act_mm() respect THREAD_SIZE
ARM: decompressor: run decompressor in place if loaded via UEFI
ARM: decompressor: move GOT into .data for EFI enabled builds
ARM: decompressor: defer loading of the contents of the LC0 structure
ARM: decompressor: split off _edata and stack base into separate object
ARM: decompressor: move headroom variable out of LC0
ARM: 8976/1: module: allow arch overrides for .init section names
ARM: 8975/1: module: fix handling of unwind init sections
ARM: 8974/1: use SPARSMEM_STATIC when SPARSEMEM is enabled
ARM: 8971/1: replace the sole use of a symbol with its definition
ARM: 8969/1: decompressor: simplify libfdt builds
Update rmk's email address in various drivers
ARM: compat: remove KERNEL_DS usage in sys_oabi_epoll_ctl()
- preliminary changes for RISC-V
- Add support for setting the resolution on the EFI framebuffer
- Simplify kernel image loading for arm64
- Move .bss into .data via the linker script instead of relying on symbol
annotations.
- Get rid of __pure getters to access global variables
- Clean up the config table matching arrays
- Rename pr_efi/pr_efi_err to efi_info/efi_err, and use them consistently
- Simplify and unify initrd loading
- Parse the builtin command line on x86 (if provided)
- Implement printk() support, including support for wide character strings
- Simplify GDT handling in early mixed mode thunking code
- Some other minor fixes and cleanups
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----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=XG4E
-----END PGP SIGNATURE-----
Merge tag 'efi-core-2020-06-01' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull EFI updates from Ingo Molnar:
"The EFI changes for this cycle are:
- preliminary changes for RISC-V
- Add support for setting the resolution on the EFI framebuffer
- Simplify kernel image loading for arm64
- Move .bss into .data via the linker script instead of relying on
symbol annotations.
- Get rid of __pure getters to access global variables
- Clean up the config table matching arrays
- Rename pr_efi/pr_efi_err to efi_info/efi_err, and use them
consistently
- Simplify and unify initrd loading
- Parse the builtin command line on x86 (if provided)
- Implement printk() support, including support for wide character
strings
- Simplify GDT handling in early mixed mode thunking code
- Some other minor fixes and cleanups"
* tag 'efi-core-2020-06-01' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (79 commits)
efi/x86: Don't blow away existing initrd
efi/x86: Drop the special GDT for the EFI thunk
efi/libstub: Add missing prototype for PE/COFF entry point
efi/efivars: Add missing kobject_put() in sysfs entry creation error path
efi/libstub: Use pool allocation for the command line
efi/libstub: Don't parse overlong command lines
efi/libstub: Use snprintf with %ls to convert the command line
efi/libstub: Get the exact UTF-8 length
efi/libstub: Use %ls for filename
efi/libstub: Add UTF-8 decoding to efi_puts
efi/printf: Add support for wchar_t (UTF-16)
efi/gop: Add an option to list out the available GOP modes
efi/libstub: Add definitions for console input and events
efi/libstub: Implement printk-style logging
efi/printf: Turn vsprintf into vsnprintf
efi/printf: Abort on invalid format
efi/printf: Refactor code to consolidate padding and output
efi/printf: Handle null string input
efi/printf: Factor out integer argument retrieval
efi/printf: Factor out width/precision parsing
...
xdp_umem.c had overlapping changes between the 64-bit math fix
for the calculation of npgs and the removal of the zerocopy
memory type which got rid of the chunk_size_nohdr member.
The mlx5 Kconfig conflict is a case where we just take the
net-next copy of the Kconfig entry dependency as it takes on
the ESWITCH dependency by one level of indirection which is
what the 'net' conflicting change is trying to ensure.
Signed-off-by: David S. Miller <davem@davemloft.net>
This time there is one fix for the error path in the mediatek cmdq driver
(used by their video driver) and a couple of devicetree fixes, mostly
for 32-bit ARM, and fairly harmless:
- On OMAP2 there were a few regressions in the ethernet drivers,
one of them leading to an external abort trap
- One Raspberry Pi version had a misconfigured LED
- Interrupts on Broadcom NSP were slightly misconfigured
- One i.MX6q board had issues with graphics mode setting
- On mmp3 there are some minor fixes that were submitted for
v5.8 with a cc:stable tag, so I ended up picking them up
here as well
- The Mediatek Video Codec needs to run at a higher frequency
than configured originally
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=E8Pg
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes-v5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"This time there is one fix for the error path in the mediatek cmdq
driver (used by their video driver) and a couple of devicetree fixes,
mostly for 32-bit ARM, and fairly harmless:
- On OMAP2 there were a few regressions in the ethernet drivers, one
of them leading to an external abort trap
- One Raspberry Pi version had a misconfigured LED
- Interrupts on Broadcom NSP were slightly misconfigured
- One i.MX6q board had issues with graphics mode setting
- On mmp3 there are some minor fixes that were submitted for v5.8
with a cc:stable tag, so I ended up picking them up here as well
- The Mediatek Video Codec needs to run at a higher frequency than
configured originally"
* tag 'armsoc-fixes-v5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
ARM: dts: mmp3: Drop usb-nop-xceiv from HSIC phy
ARM: dts: mmp3-dell-ariel: Fix the SPI devices
ARM: dts: mmp3: Use the MMP3 compatible string for /clocks
ARM: dts: bcm: HR2: Fix PPI interrupt types
ARM: dts: bcm2835-rpi-zero-w: Fix led polarity
ARM: dts/imx6q-bx50v3: Set display interface clock parents
soc: mediatek: cmdq: return send msg error code
arm64: dts: mt8173: fix vcodec-enc clock
ARM: dts: Fix wrong mdio clock for dm814x
ARM: dts: am437x: fix networking on boards with ksz9031 phy
ARM: dts: am57xx: fix networking on boards with ksz9031 phy
The device node name should reflect generic class of a device so rename
the "msmram" node and its children to "sram". This will be also in sync
with upcoming DT schema. No functional change.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Enable ethernet wake-on-lan feature for imx6q/dl/qp sabresd
boards since the PHY clock is supplied by external osc.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Update the imx6qdl gpr property to define gpr register
offset and bit in DT.
- Add imx6sx/imx6ul/imx7d ethernet stop mode property.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- correct value of decompressor tag size in header
- fix DACR value when we have nested exceptions
- fix a missing newline on a kernel message
- fix mask for ptrace thumb breakpoint hook
-----BEGIN PGP SIGNATURE-----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=dAx4
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm
Pull ARM fixes from Russell King:
- correct value of decompressor tag size in header
- fix DACR value when we have nested exceptions
- fix a missing newline on a kernel message
- fix mask for ptrace thumb breakpoint hook
* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 8977/1: ptrace: Fix mask for thumb breakpoint hook
ARM: 8973/1: Add missing newline terminator to kernel message
ARM: uaccess: fix DACR mismatch with nested exceptions
ARM: uaccess: integrate uaccess_save and uaccess_restore
ARM: uaccess: consolidate uaccess asm to asm/uaccess-asm.h
ARM: 8970/1: decompressor: increase tag size
- A series from Anson Huang updating SRC devices to match bindings
schema definition.
- Correct CPU supply name and add cpu1 supply for i.MX7D.
- Convert thermal device to use nvmem interface to get fuse data
for imx6qdl and imx6sl.
- A series from Tim Harvey to update imx6qdl-gw devices, adding support
of LSM9DS1 IIO imu/magn, USB OTG, bcm4330-bt, etc.
- Add input MUX for ENET2 MDIO into IMX7D pin functions.
- Misc random device addition or update.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCgAyFiEEFmJXigPl4LoGSz08UFdYWoewfM4FAl7IhYQUHHNoYXduZ3Vv
QGtlcm5lbC5vcmcACgkQUFdYWoewfM5Bvwf8Cy/gm3ezs2OmjtdF3jql86qo7tqk
nUwPDnRhlPYInN8yKlipMsYn2yupCPSwENGYwxLculwsHyQ7RNEI8a1jY2zEkdh9
+IoZCNeOxOk40iQoCtaxBAJVz73BY8ptdKgfKL44xQ32e4oVQrgw1iAPdNS60yzl
5TRXxghYnfeRC5c7ZKKEF0X74RzWb/zwEWAcs3yczuPzQGAtcBmYTG8b/y+/HNT0
oTTcnN+clw48xAPuq6/8nMseVMLqTzyyBQpn/TI78LWGfBtaTIv6l7pjZBquhSGi
+QYKHgbC3POv8TYWGu+csqFfQvbfeiO/HEHFKPcvJ8O+QoRMB9nvejn42Q==
=I7h9
-----END PGP SIGNATURE-----
Merge tag 'imx-dt-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/dt
i.MX device tree changes for 5.8:
- A series from Anson Huang updating SRC devices to match bindings
schema definition.
- Correct CPU supply name and add cpu1 supply for i.MX7D.
- Convert thermal device to use nvmem interface to get fuse data
for imx6qdl and imx6sl.
- A series from Tim Harvey to update imx6qdl-gw devices, adding support
of LSM9DS1 IIO imu/magn, USB OTG, bcm4330-bt, etc.
- Add input MUX for ENET2 MDIO into IMX7D pin functions.
- Misc random device addition or update.
* tag 'imx-dt-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (22 commits)
ARM: dts: imx53-cx9020: Group port definitions for the dvi-converter
ARM: dts: imx5: make src node name generic
ARM: dts: imx50: Add src node interrupt
ARM: dts: imx: make src node name generic
ARM: dts: imx7d-pinfunc: add input mux for ENET2 mdio
ARM: dts: imx6sl: Use nvmem interface to get fuse data
ARM: dts: imx6qdl: Use nvmem interface to get fuse data
ARM: dts: imx6qdl-gw5910: fix wlan regulator
ARM: dts: imx6qdl-gw5910: add support for bcm4330-bt
ARM: dts: imx6qdl-gw5904: add lsm9ds1 iio imu/magn support
ARM: dts: imx6qdl-gw560x: add lsm9ds1 iio imu/magn support
ARM: dts: imx53: Add src node interrupt
ARM: dts: imx51: Add src node interrupt
ARM: dts: imx50: Remove unused iomuxc-gpr node
ARM: dts: imx6qdl-gw552x: add USB OTG support
ARM: dts: imx6-sr-som: add ethernet PHY configuration
arm: dts: ls1021atwr: Add QSPI node properties
ARM: dts: e60k02: add interrupt for PMIC
ARM: dts: colibri: introduce device trees with UHS-I support
ARM: dts: imx7d: Add cpu1 supply
...
Link: https://lore.kernel.org/r/20200523032516.11016-4-shawnguo@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- eth PHY and USB PHY updates
-----BEGIN PGP SIGNATURE-----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=H41z
-----END PGP SIGNATURE-----
Merge tag 'amlogic-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into arm/dt
ARM: dts: Amlogic updates for v5.8
- eth PHY and USB PHY updates
* tag 'amlogic-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
ARM: dts: meson: Switch existing boards with RGMII PHY to "rgmii-id"
ARM: dts: meson: Add the Ethernet "timing-adjustment" clock
ARM: dts: meson8m2: Use the Meson8m2 specific USB2 PHY compatible
ARM: dts: meson: add the gadget mode properties to the USB0 controller
Link: https://lore.kernel.org/r/5ec6f524.1c69fb81.b979a.ae15@mx.google.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Recent cpsw driver changes exposed few regressions in the cpsw related
dts configuration that would be good to fix:
- Few more boards still need to be updated to use rgmii-rxid phy caused
by the fallout from commit bcf3440c6d ("net: phy: micrel: add phy-mode
support for the KSZ9031 PHY" as the rx delay is now disabled unless we
use rgmii-rxid.
- On dm814x we have been using a wrong clock for mdio that now can produce
external abort on some boards
-----BEGIN PGP SIGNATURE-----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=tWSS
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.7/cpsw-fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes
Few cpsw related dts fixes for omaps
Recent cpsw driver changes exposed few regressions in the cpsw related
dts configuration that would be good to fix:
- Few more boards still need to be updated to use rgmii-rxid phy caused
by the fallout from commit bcf3440c6d ("net: phy: micrel: add phy-mode
support for the KSZ9031 PHY" as the rx delay is now disabled unless we
use rgmii-rxid.
- On dm814x we have been using a wrong clock for mdio that now can produce
external abort on some boards
* tag 'omap-for-v5.7/cpsw-fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Fix wrong mdio clock for dm814x
ARM: dts: am437x: fix networking on boards with ksz9031 phy
ARM: dts: am57xx: fix networking on boards with ksz9031 phy
Link: https://lore.kernel.org/r/pull-1589472123-367692@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This series of changes finally gets the legacy omap dual-mode timer and
32k counter system timer updated to use drivers/clocksource and device
tree data. And we can now remove the unused legacy platform data.
These changes are based on an immutable clocksource branch set up by
Daniel Lezcano.
-----BEGIN PGP SIGNATURE-----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=07SB
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.8/timer-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/soc
System timer changes for omaps for v5.8 merge window
This series of changes finally gets the legacy omap dual-mode timer and
32k counter system timer updated to use drivers/clocksource and device
tree data. And we can now remove the unused legacy platform data.
These changes are based on an immutable clocksource branch set up by
Daniel Lezcano.
* tag 'omap-for-v5.8/timer-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
bus: ti-sysc: Timers no longer need legacy quirk handling
ARM: OMAP2+: Drop old timer code for dmtimer and 32k counter
ARM: dts: Configure system timers for omap2
ARM: dts: Configure system timers for ti81xx
ARM: dts: Configure system timers for omap3
ARM: dts: Configure system timers for omap5 and dra7
ARM: dts: Configure system timers for omap4
ARM: dts: Configure system timers for am437x
ARM: dts: Configure system timers for am335x
ARM: OMAP2+: Add omap_init_time_of()
bus: ti-sysc: Ignore timer12 on secure omap3
clk: ti: dm816: enable sysclk6_ck on init
clocksource/drivers/timer-ti-dm: Fix warning for set but not used
clocksource/drivers/timer-ti-dm: Add clockevent and clocksource support
clocksource/drivers/timer-ti-32k: Add support for initializing directly
Link: https://lore.kernel.org/r/pull-1590169577-735045@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Rename pr_efi/pr_efi_err to efi_info/efi_err, and use them consistently
- Simplify and unify initrd loading
- Parse the builtin command line on x86 (if provided)
- Implement printk() support, including support for wide character strings
- Some fixes for issues introduced by the first batch of v5.8 changes
- Fix a missing prototypes warning
- Simplify GDT handling in early mixed mode thunking code
- Some other minor fixes and cleanups
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEnNKg2mrY9zMBdeK7wjcgfpV0+n0FAl7Lb8UACgkQwjcgfpV0
+n3/aAgAkEqqR/BoyzFiyYHujq6bXjESKYr8LrIjNWfnofB6nZqp1yXwFdL0qbj/
PTZ1qIQAnOMmj11lvy1X894h2ZLqE6XEkqv7Xd2oxkh3fF6amlQUWfMpXUuGLo1k
C4QGSfA0OOiM0OOi0Aqk1fL7sTmH23/j63dTR+fH8JMuYgjdls/yWNs0miqf8W2H
ftj8fAKgHIJzFvdTC0vn1DZ6dEKczGLPEcVZ2ns2IJOJ69DsStKPLcD0mlW+EgV2
EyfRSCQv55RYZRhdUOb+yVLRfU0M0IMDrrCDErHxZHXnQy00tmKXiEL20yuegv3u
MUtRRw8ocn2/RskjgZkxtMjAAlty9A==
=AwCh
-----END PGP SIGNATURE-----
Merge tag 'efi-changes-for-v5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi into efi/core
More EFI changes for v5.8:
- Rename pr_efi/pr_efi_err to efi_info/efi_err, and use them consistently
- Simplify and unify initrd loading
- Parse the builtin command line on x86 (if provided)
- Implement printk() support, including support for wide character strings
- Some fixes for issues introduced by the first batch of v5.8 changes
- Fix a missing prototypes warning
- Simplify GDT handling in early mixed mode thunking code
- Some other minor fixes and cleanups
Conflicts:
drivers/firmware/efi/libstub/efistub.h
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Rather busy cycle. We have a total 99 non-merge commits going into v5.8
merge window. The majority of the changes are in dwc3 this around (31.7%
of all changes). It's composed mostly Thinh's recent updates to get dwc3
to behave correctly with stream transfers. We have also have Roger's for
Keystone platforms and Neil's updates for the meson glue layer.
Apart from those, we have the usual set of non-critical fixes, new
device IDs, spelling fixes all over the place.
Signed-off-by: Felipe Balbi <balbi@kernel.org>
-----BEGIN PGP SIGNATURE-----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=OiS0
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
USB: changes for v5.8 merge window
Rather busy cycle. We have a total 99 non-merge commits going into v5.8
merge window. The majority of the changes are in dwc3 this around (31.7%
of all changes). It's composed mostly Thinh's recent updates to get dwc3
to behave correctly with stream transfers. We have also have Roger's for
Keystone platforms and Neil's updates for the meson glue layer.
Apart from those, we have the usual set of non-critical fixes, new
device IDs, spelling fixes all over the place.
Signed-off-by: Felipe Balbi <balbi@kernel.org>
* tag 'usb-for-v5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb: (99 commits)
usb: dwc3: keystone: Turn on USB3 PHY before controller
dt-bindings: usb: ti,keystone-dwc3.yaml: Add USB3.0 PHY property
dt-bindings: usb: convert keystone-usb.txt to YAML
usb: dwc3: gadget: Check for prepared TRBs
usb: gadget: Fix issue with config_ep_by_speed function
usb: cdns3: ep0: delete the redundant status stage
usb: dwc2: Update Core Reset programming flow.
usb: gadget: fsl: Fix a wrong judgment in fsl_udc_probe()
usb: gadget: fix potential double-free in m66592_probe.
usb: cdns3: Fix runtime PM imbalance on error
usb: gadget: lpc32xx_udc: don't dereference ep pointer before null check
usb: dwc3: Increase timeout for CmdAct cleared by device controller
USB: dummy-hcd: use configurable endpoint naming scheme
usb: cdns3: gadget: assign interrupt number to USB gadget structure
usb: gadget: core: sync interrupt before unbind the udc
arm64: dts: qcom: sc7180: Add interconnect properties for USB
arm64: dts: qcom: sdm845: Add interconnect properties for USB
dt-bindings: usb: qcom,dwc3: Introduce interconnect properties for Qualcomm DWC3 driver
ARM: dts: at91: Remove the USB EP child node
dt-bindings: usb: atmel: Mark EP child node as deprecated
...
5.7, please pull the following:
- Vincent fixes the polarity of the ACT LED on the Raspberry Pi Zero W
board
- Hamish fixes the ARM PPI interrupts sensitivy for the Hurricane 2
SoCs
-----BEGIN PGP SIGNATURE-----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=klA0
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-5.7/devicetree-fixes-part2-v2' of https://github.com/Broadcom/stblinux into arm/fixes
This pull request contains Broadcom ARM-based SoCs Device Tree fixes for
5.7, please pull the following:
- Vincent fixes the polarity of the ACT LED on the Raspberry Pi Zero W
board
- Hamish fixes the ARM PPI interrupts sensitivy for the Hurricane 2
SoCs
* tag 'arm-soc/for-5.7/devicetree-fixes-part2-v2' of https://github.com/Broadcom/stblinux:
ARM: dts: bcm: HR2: Fix PPI interrupt types
ARM: dts: bcm2835-rpi-zero-w: Fix led polarity
Link: https://lore.kernel.org/r/20200524203714.17035-1-f.fainelli@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
