On pre-r6xx, the power mode array is usually ordered:
low
...
high
default
On r6xx+:
default
low
...
high
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
set proper wait condition as noted by Rafał Miłecki.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Useful for certain power management operations. You
need to wait for the GUI engine (2D, 3D, CP, etc.) to be
idle before changing clocks or adjusting engine parameters.
(v2) Fix gui idle enable on pre-r6xx asics
(v3) The gui idle interrrupt status bit is permanently asserted
on pre-r6xx chips, but the interrrupt is still generated.
workaround it in the driver.
(v4) Add support for evergreen
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Check to see if the GUI engine and related blocks
(2D, 3D, CP, etc) are idle or not. There are a number
of cases when we need to know if the drawing engine
is busy.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
After thinking it over a lot it made more sense for the core to deal with
the output polling especially so it can notify X.
v2: drop plans for fake connector - per Michel's comments - fix X patch sent to xorg-devel, add intel polled/hpd setting, add initial nouveau polled/hpd settings.
v3: add config lock take inside polling, add intel/nouveau poll init/fini calls
v4: config lock was a bit agressive, only needed around connector list reading.
otherwise it could re-enter.
glisse: discard drm_helper_hpd_irq_event
v3: Reviewed-by: Michel Dänzer <michel@daenzer.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
It removes a hack from nouveau code which had to detect which
region to pass to kick vesafb/efifb.
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Peter Jones <pjones@redhat.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Userspace need to know the hw crtc id (0, 1, 2, ...) from the drm
crtc id. Bump the minor version so userspace can enable conditionaly
features depend on this.
V2 use num_crtc and avoid DRM_ERROR
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Use kmemdup when some other buffer is immediately copied into the
allocated region.
A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression from,to,size,flag;
statement S;
@@
- to = \(kmalloc\|kzalloc\)(size,flag);
+ to = kmemdup(from,size,flag);
if (to==NULL || ...) S
- memcpy(to, from, size);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fixes LVDS issues on some laptops; notably laptops with
2048x1536 panels.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Previously we just set them to dpms off. This should save
additional power.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Previous reset code leaded to computer hard lockup (need to unplug
the power too reboot the computer) on various configuration. This
patch change the reset code to avoid hard lockup. The GPU reset
is failing most of the time but at least user can log in remotely
or properly shutdown the computer.
Two issues were leading to hard lockup :
- Writting to the scratch register lead to hard lockup most likely
because the write back mecanism is in fuzy state after GPU lockup.
- Resetting the GPU memory controller and not reinitializing it
after leaded to hard lockup. We did only reinitialize in case of
successfull reset thus unsuccessfull reset quickly leaded to hard
lockup.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Implements irq support for HDMI audio output. Now the polling timer
is only enabled if irq support isn't available.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Rework HDMI audio polling timer, only enable it when
at least one HDMI encoder needs it. Preparation for
replacing it with irq support.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* drm-ttm-unmappable:
drm/radeon/kms: enable use of unmappable VRAM V2
drm/ttm: remove io_ field from TTM V6
drm/vmwgfx: add support for new TTM fault callback V5
drm/nouveau/kms: add support for new TTM fault callback V5
drm/radeon/kms: add support for new fault callback V7
drm/ttm: ttm_fault callback to allow driver to handle bo placement V6
drm/ttm: split no_wait argument in 2 GPU or reserve wait
Conflicts:
drivers/gpu/drm/nouveau/nouveau_bo.c
This patch enable the use of unmappable VRAM thanks to
previous TTM infrastructure change.
V2 update after io_mem_reserve/io_mem_free callback balancing
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
All TTM driver have been converted to new io_mem_reserve/free
interface which allow driver to choose and return proper io
base, offset to core TTM for ioremapping if necessary. This
patch remove what is now deadcode.
V2 adapt to match with change in first patch of the patchset
V3 update after io_mem_reserve/io_mem_free callback balancing
V4 adjust to minor cleanup
V5 remove the needs ioremap flag
V6 keep the ioremapping facility in TTM
[airlied- squashed driver removals in here also]
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This add the support for the new fault callback and also the
infrastructure for supporting unmappable VRAM.
V2 validate BO with no_wait = true
V3 don't derefence bo->mem.mm_node as it's not NULL only for
VRAM or GTT
V4 update to splitted no_wait ttm change
V5 update to new balanced io_mem_reserve/free change
V6 callback is responsible for iomapping memory
V7 move back iomapping to ttm
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
When drivers embed the core gem object into their own structures,
they'll have to do this. Temporarily this results in an ugly
kfree(gem_obj);
in every gem driver.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* drm-radeon-evergreen-accel:
drm/radeon: fix cypress firmware typo.
drm/radeon/kms/evergreen: add hpd support
drm/radeon/kms/evergreen: implement irq support
drm/radeon/kms/evergreen: setup and enable the CP
drm/radeon/kms/evergreen: implement gfx init
drm/radeon/kms/evergreen: add soft reset function
drm/radeon/kms/evergreen: add gart support
drm/radeon/kms: add support for evergreen power tables
drm/radeon/kms: update atombios.h power tables for evergreen
* drm-fbdev-cleanup:
drm/fb: remove drm_fb_helper_setcolreg
drm/kms/fb: use slow work mechanism for normal hotplug also.
drm/kms/fb: add polling support for when nothing is connected.
drm/kms/fb: provide a 1024x768 fbcon if no outputs found.
drm/kms/fb: separate fbdev connector list from core drm connectors
drm/kms/fb: move to using fb helper crtc grouping instead of core crtc list
drm/fb: fix fbdev object model + cleanup properly.
Conflicts:
drivers/gpu/drm/i915/i915_drv.h
drivers/gpu/drm/nouveau/nouveau_drv.h
* drm-edid-fixes:
drm/edid: When checking duplicate standard modes, walked the probed list
drm/edid: Fix sync polarity for secondary GTF curve
drm/modes: Fix interlaced mode names
drm/edid: Add secondary GTF curve support
drm/edid: Strengthen the algorithm for standard mode codes
drm/edid: Fix the HDTV hack.
drm/edid: Extend range-based mode addition for EDID 1.4
drm/edid: Add test for monitor reduced blanking support.
drm/edid: Fix preferred mode parse for EDID 1.4
drm/edid: Remove some silly comments
drm/edid: Remove arbitrary EDID extension limit
drm/edid: Add modes for Established Timings III section
drm/edid: Reshuffle mode list construction to closer match the spec
drm/edid: Remove a redundant check
drm/edid: Remove some misleading comments
drm/edid: Fix secondary block fetch.
* drm-ttm-pool:
drm/ttm: using kmalloc/kfree requires including slab.h
drm/ttm: include linux/seq_file.h for seq_printf
drm/ttm: Add sysfs interface to control pool allocator.
drm/ttm: Use set_pages_array_wc instead of set_memory_wc.
arch/x86: Add array variants for setting memory to wc caching.
drm/nouveau: Add ttm page pool debugfs file.
drm/radeon/kms: Add ttm page pool debugfs file.
drm/ttm: Add debugfs output entry to pool allocator.
drm/ttm: add pool wc/uc page allocator V3
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon/kms: add FireMV 2400 PCI ID.
drm/radeon/kms: allow R500 regs VAP_ALT_NUM_VERTICES and VAP_INDEX_OFFSET
drivers/gpu/radeon: Add MSPOS regs to safe list.
drm/radeon/kms: disable the tv encoder when tv/cv is not in use
drm/radeon/kms: adjust pll settings for tv
drm/radeon/kms: fix tv dac conflict resolver
drm/radeon/kms/evergreen: don't enable hdmi audio stuff
drm/radeon/kms/atom: fix dual-link DVI on DCE3.2/4.0
drm/radeon/kms: fix rs600 tlb flush
drm/radeon/kms: print GPU family and device id when loading
drm/radeon/kms: fix calculation of mipmapped 3D texture sizes
drm/radeon/kms: only change mode when coherent value changes.
drm/radeon/kms: more atom parser fixes (v2)
[airlied: fix V_A_N_V to not be safe and fix check to make sure only r500
- bump userspace version]
Signed-off-by: Marek Olšák <maraeo@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Switching between TV and VGA caused VGA to break on some systems
since the TV encoder was left enabled when VGA was used.
fixes fdo bug 25520.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
On systems with the tv dac shared between DVI and TV,
we can only use the dac for one of the connectors.
However, when using a digital monitor on the DVI port,
you can use the dac for the TV connector just fine.
Check the use_digital status when resolving the conflict.
Fixes fdo bug 27649, possibly others.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Got broken during the evergreen merge.
Fixes fdo bug 27001.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Typo in in flush leaded to no flush of the RS600 tlb which
ultimately leaded to massive system ram corruption, with
this patch everythings seems to work properly.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This will help figuring out GPU when looking at bugs log.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
On X startup we were getting a flicker where there shouldn't have been one.
the X DDX calls the kernel to set the properties to the same values (yes
it could be smarter), however the kernel was doing a pointless modeset then,
making my nice smooth boot ugly.
Signed-off-by: Dave Airlie <airlied@redhat.com>
shr/shl ops need the full dst rather than the pre-masked
version. Fixes fdo bug 27478 and kernel bug 15738.
v2: remove some unsed vars, add comments
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (29 commits)
drm/nouveau: bail out of auxch transaction if we repeatedly recieve defers
drm/nv50: implement gpio set/get routines
drm/nv50: parse/use some more de-magiced parts of gpio table entries
drm/nouveau: store raw gpio table entry in bios gpio structs
drm/nv40: Init some tiling-related PGRAPH state.
drm/nv50: Add NVA3 support in ctxprog/ctxvals generator.
drm/nv50: another dodgy DP hack
drm/nv50: punt hotplug irq handling out to workqueue
drm/nv50: preserve an unknown SOR_MODECTRL value for DP encoders
drm/nv50: Allow using the NVA3 new compute class.
drm/nv50: cleanup properly if PDISPLAY init fails
drm/nouveau: fixup the init failure paths some more
drm/nv50: fix instmem init on IGPs if stolen mem crosses 4GiB mark
drm/nv40: add LVDS table quirk for Dell Latitude D620
drm/nv40: rework lvds table parsing
drm/nouveau: detect vram amount once, and save the value
drm/nouveau: remove some unused members from drm_nouveau_private
drm/nouveau: Make use of TTM busy_placements.
drm/nv50: add more 0x100c80 flushy magic
drm/nv50: fix fbcon when framebuffer above 4GiB mark
...
The command processor (CP) fetches command buffers and
feeds the GPU. This patch requires the evergreen
family me and pfp ucode files.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This initializes the gfx engine so accel can
eventually be used.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Gart setup is more or less like r7xx. Copy
rv770d.h to evergreend.h and fix up changes.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
