Add support to Magic Packet Detection with Secure-ON for PCI11010/PCI11414 chips
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support to LAN743x common register dump
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alvin Šipraga says:
====================
net: dsa: realtek: rtl8365mb: improve handling of PHY modes
This series introduces some minor cleanup of the driver and improves the
handling of PHY interface modes to break the assumption that CPU ports
are always over an external interface, and the assumption that user
ports are always using an internal PHY.
====================
Link: https://lore.kernel.org/r/20220615225116.432283-1-alvin@pqrs.dk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Realtek switches in the rtl8365mb family always have at least one port
with a so-called external interface, supporting PHY interface modes such
as RGMII or SGMII. The purpose of this patch is to improve the driver's
handling of these ports.
A new struct rtl8365mb_chip_info is introduced together with a static
array of such structs. An instance of this struct is added for each
supported switch, distinguished by its chip ID and version. Embedded in
each chip_info struct is an array of struct rtl8365mb_extint, describing
the external interfaces available. This is more specific than the old
rtl8365mb_extint_port_map, which was only valid for switches with up to
6 ports.
The struct rtl8365mb_extint also contains a bitmask of supported PHY
interface modes, which allows the driver to distinguish which ports
support RGMII. This corrects a previous mistake in the driver whereby it
was assumed that any port with an external interface supports RGMII.
This is not actually the case: for example, the RTL8367S has two
external interfaces, only the second of which supports RGMII. The first
supports only SGMII and HSGMII. This new design will make it easier to
add support for other interface modes.
Finally, rtl8365mb_phylink_get_caps() is fixed up to return supported
capabilities based on the external interface properties described above.
This addresses Vladimir's point in the linked thread that the
capabilities are not actually a function of the DSA port type: Although
most typical applications will treat the ports with internal PHY as user
ports, there is no actual hardware limitation preventing one from using
them as a CPU port. Equally, ports with external interface(s) may well
be treated as user ports, even though it is typical to use those ports
as CPU ports.
Link: https://lore.kernel.org/netdev/20220510192301.5djdt3ghoavxulhl@bang-olufsen.dk/
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Acked-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Acked-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The variable is just assigned the value of a macro, so it can be
removed.
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The maximum number of ports is actually 11, according to two
observations:
1. The highest port ID used in the vendor driver is 10. Since port IDs
are indexed from 0, and since DSA follows the same numbering system,
this means up to 11 ports are to be presumed.
2. The registers with port mask fields always amount to a maximum port
mask of 0x7FF, corresponding to a maximum 11 ports.
In view of this, I also deleted the comment.
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There is no real need for this variable: the line change interrupt mask
is sufficiently masked out when getting linkup_ind and linkdown_ind in
the interrupt handler.
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The official name of this switch is RTL8367RB-VB, not RTL8367RB. There
is also an RTL8367RB-VC which is rather different. Change the name of
the CHIP_ID/_VER macros for reasons of consistency.
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alex Elder says:
====================
net: ipa: more multi-channel event ring work
This series makes a little more progress toward supporting multiple
channels with a single event ring. The first removes the assumption
that consecutive events are associated with the same RX channel.
The second derives the channel associated with an event from the
event itself, and the next does a small cleanup enabled by that.
The fourth causes updates to occur for every event processed (rather
once). And the final patch does a little more rework to make TX
completion have more in common with RX completion.
====================
Link: https://lore.kernel.org/r/20220615165929.5924-1-elder@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Move the processing done for TX channels in gsi_channel_update()
into gsi_evt_ring_rx_update(). The called function is called for
both RX and TX channels, so rename it to be gsi_evt_ring_update().
As a result, this code no longer assumes events in an event ring are
associated with just one channel.
Because all events in a ring are handled in that function, we can
move the call to gsi_trans_move_complete() there, and can ring the
event ring doorbell there as well after all new events in the ring
have been processed.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When an RX transaction completes, we update the trans->len field to
contain the actual number of bytes received. This is done in a loop
in gsi_evt_ring_rx_update().
Change that function so it checks the data transfer direction
recorded in the transaction, and only updates trans->len for RX
transfers.
Then call it unconditionally. This means events for TX endpoints
will run through the loop without otherwise doing anything, but
this will change shortly.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The only reason the event ring's channel pointer is needed in
gsi_evt_ring_rx_update() is so we can get at its GSI pointer.
We can pass the GSI pointer as an argument, along with the event
ring ID, and thereby avoid using the event ring channel pointer.
This is another step toward no longer assuming an event ring
services a single channel.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Change gsi_channel_trans_map() so it derives the channel used from
the transaction. Pass the index of the *first* TRE used by the
transaction, and have the called function account for the fact that
the last one used is what's important.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In gsi_evt_ring_rx_update(), use gsi_event_trans() repeatedly
to find the transaction associated with an event, rather than
assuming consecutive events are associated with the same channel.
This removes the only caller of gsi_trans_pool_next(), so get rid
of it.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Rasmus Villemoes says:
====================
dt-bindings: dp83867: add binding for io_impedance_ctrl nvmem cell
We have a board where measurements indicate that the current three
options - leaving IO_IMPEDANCE_CTRL at the reset value (which is
factory calibrated to a value corresponding to approximately 50 ohms)
or using one of the two boolean properties to set it to the min/max
value - are too coarse.
This series adds a device tree binding for an nvmem cell which can be
populated during production with a suitable value calibrated for each
board, and corresponding support in the driver. The second patch adds
a trivial phy wrapper for dev_err_probe(), used in the third.
====================
Link: https://lore.kernel.org/r/20220614084612.325229-1-linux@rasmusvillemoes.dk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We have a board where measurements indicate that the current three
options - leaving IO_IMPEDANCE_CTRL at the (factory calibrated) reset
value or using one of the two boolean properties to set it to the
min/max value - are too coarse.
Implement support for the newly added binding allowing device tree to
specify an nvmem cell containing an appropriate value for this
specific board.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The dev_err_probe() function is quite useful to avoid boilerplate
related to -EPROBE_DEFER handling. Add a phydev_err_probe() helper to
simplify making use of that from phy drivers which otherwise use the
phydev_* helpers.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We have a board where measurements indicate that the current three
options - leaving IO_IMPEDANCE_CTRL at the reset value (which is
factory calibrated to a value corresponding to approximately 50 ohms)
or using one of the two boolean properties to set it to the min/max
value - are too coarse.
There is no fixed mapping from register values to values in the range
35-70 ohms; it varies from chip to chip, and even that target range is
approximate. So add a DT binding for an nvmem cell which can be
populated during production with a value suitable for each specific
board.
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Delyan Kratunov says:
====================
This series implements support for sleepable uprobe programs.
Key work is in patches 2 and 3, the rest is plumbing and tests.
The main observation is that the only obstacle in the way of sleepable uprobe
programs is not the uprobe infrastructure, which already runs in a user-like
context, but the rcu usage around bpf_prog_array.
Details are in patch 2 but the tl;dr is that we chain trace_tasks and normal rcu
grace periods when releasing to array to accommodate users of either rcu type.
This introduces latency for non-sleepable users (kprobe, tp) but that's deemed
acceptable, given recent benchmarks by Andrii [1]. We're a couple of orders of
magnitude under the rate of bpf_prog_array churn that would raise flags (~1MM/s per Paul).
[1]: https://lore.kernel.org/bpf/CAEf4BzbpjN6ca7D9KOTiFPOoBYkciYvTz0UJNp5c-_3ptm=Mrg@mail.gmail.com/
v3 -> v4:
* Fix kdoc and inline issues
* Rebase
v2 -> v3:
* Inline uprobe_call_bpf into trace_uprobe.c, it's just a bpf_prog_run_array_sleepable call now.
* Do not disable preemption for uprobe non-sleepable programs.
* Add acks.
v1 -> v2:
* Fix lockdep annotations in bpf_prog_run_array_sleepable
* Chain rcu grace periods only for perf_event-attached programs. This limits
the additional latency on the free path to use cases where we know it won't
be a problem.
* Add tests calling helpers only available in sleepable programs.
* Remove kprobe.s support from libbpf.
====================
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Add tests that ensure sleepable uprobe programs work correctly.
Add tests that ensure sleepable kprobe programs cannot attach.
Also add tests that attach both sleepable and non-sleepable
uprobe programs to the same location (i.e. same bpf_prog_array).
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Delyan Kratunov <delyank@fb.com>
Link: https://lore.kernel.org/r/c744e5bb7a5c0703f05444dc41f2522ba3579a48.1655248076.git.delyank@fb.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
uprobe and kprobe programs have the same program type, KPROBE, which is
currently not allowed to load sleepable programs.
To avoid adding a new UPROBE type, instead allow sleepable KPROBE
programs to load and defer the is-it-actually-a-uprobe-program check
to attachment time, where there's already validation of the
corresponding perf_event.
A corollary of this patch is that you can now load a sleepable kprobe
program but cannot attach it.
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Delyan Kratunov <delyank@fb.com>
Link: https://lore.kernel.org/r/fcd44a7cd204f372f6bb03ef794e829adeaef299.1655248076.git.delyank@fb.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
uprobes work by raising a trap, setting a task flag from within the
interrupt handler, and processing the actual work for the uprobe on the
way back to userspace. As a result, uprobe handlers already execute in a
might_fault/_sleep context. The primary obstacle to sleepable bpf uprobe
programs is therefore on the bpf side.
Namely, the bpf_prog_array attached to the uprobe is protected by normal
rcu. In order for uprobe bpf programs to become sleepable, it has to be
protected by the tasks_trace rcu flavor instead (and kfree() called after
a corresponding grace period).
Therefore, the free path for bpf_prog_array now chains a tasks_trace and
normal grace periods one after the other.
Users who iterate under tasks_trace read section would
be safe, as would users who iterate under normal read sections (from
non-sleepable locations).
The downside is that the tasks_trace latency affects all perf_event-attached
bpf programs (and not just uprobe ones). This is deemed safe given the
possible attach rates for kprobe/uprobe/tp programs.
Separately, non-sleepable programs need access to dynamically sized
rcu-protected maps, so bpf_run_prog_array_sleepables now conditionally takes
an rcu read section, in addition to the overarching tasks_trace section.
Signed-off-by: Delyan Kratunov <delyank@fb.com>
Link: https://lore.kernel.org/r/ce844d62a2fd0443b08c5ab02e95bc7149f9aeb1.1655248076.git.delyank@fb.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
In order to add a version of bpf_prog_run_array which accesses the
bpf_prog->aux member, bpf_prog needs to be more than a forward
declaration inside bpf.h.
Given that filter.h already includes bpf.h, this merely reorders
the type declarations for filter.h users. bpf.h users now have access to
bpf_prog internals.
Signed-off-by: Delyan Kratunov <delyank@fb.com>
Link: https://lore.kernel.org/r/3ed7824e3948f22d84583649ccac0ff0d38b6b58.1655248076.git.delyank@fb.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Perform the same virtual address to file offset translation that libbpf
is doing for executable ELF binaries also for shared libraries.
Currently libbpf is making a simplifying and sometimes wrong assumption
that for shared libraries relative virtual addresses inside ELF are
always equal to file offsets.
Unfortunately, this is not always the case with LLVM's lld linker, which
now by default generates quite more complicated ELF segments layout.
E.g., for liburandom_read.so from selftests/bpf, here's an excerpt from
readelf output listing ELF segments (a.k.a. program headers):
Type Offset VirtAddr PhysAddr FileSiz MemSiz Flg Align
PHDR 0x000040 0x0000000000000040 0x0000000000000040 0x0001f8 0x0001f8 R 0x8
LOAD 0x000000 0x0000000000000000 0x0000000000000000 0x0005e4 0x0005e4 R 0x1000
LOAD 0x0005f0 0x00000000000015f0 0x00000000000015f0 0x000160 0x000160 R E 0x1000
LOAD 0x000750 0x0000000000002750 0x0000000000002750 0x000210 0x000210 RW 0x1000
LOAD 0x000960 0x0000000000003960 0x0000000000003960 0x000028 0x000029 RW 0x1000
Compare that to what is generated by GNU ld (or LLVM lld's with extra
-znoseparate-code argument which disables this cleverness in the name of
file size reduction):
Type Offset VirtAddr PhysAddr FileSiz MemSiz Flg Align
LOAD 0x000000 0x0000000000000000 0x0000000000000000 0x000550 0x000550 R 0x1000
LOAD 0x001000 0x0000000000001000 0x0000000000001000 0x000131 0x000131 R E 0x1000
LOAD 0x002000 0x0000000000002000 0x0000000000002000 0x0000ac 0x0000ac R 0x1000
LOAD 0x002dc0 0x0000000000003dc0 0x0000000000003dc0 0x000262 0x000268 RW 0x1000
You can see from the first example above that for executable (Flg == "R E")
PT_LOAD segment (LOAD #2), Offset doesn't match VirtAddr columns.
And it does in the second case (GNU ld output).
This is important because all the addresses, including USDT specs,
operate in a virtual address space, while kernel is expecting file
offsets when performing uprobe attach. So such mismatches have to be
properly taken care of and compensated by libbpf, which is what this
patch is fixing.
Also patch clarifies few function and variable names, as well as updates
comments to reflect this important distinction (virtaddr vs file offset)
and to ephasize that shared libraries are not all that different from
executables in this regard.
This patch also changes selftests/bpf Makefile to force urand_read and
liburand_read.so to be built with Clang and LLVM's lld (and explicitly
request this ELF file size optimization through -znoseparate-code linker
parameter) to validate libbpf logic and ensure regressions don't happen
in the future. I've bundled these selftests changes together with libbpf
changes to keep the above description tied with both libbpf and
selftests changes.
Fixes: 74cc6311ce ("libbpf: Add USDT notes parsing and resolution logic")
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20220616055543.3285835-1-andrii@kernel.org
Current release - regressions:
- Revert "net: Add a second bind table hashed by port and address",
needs more work
- amd-xgbe: use platform_irq_count(), static setup of IRQ resources
had been removed from DT core
- dts: at91: ksz9477_evb: add phy-mode to fix port/phy validation
Current release - new code bugs:
- hns3: modify the ring param print info
Previous releases - always broken:
- axienet: make the 64b addressable DMA depends on 64b architectures
- iavf: fix issue with MAC address of VF shown as zero
- ice: fix PTP TX timestamp offset calculation
- usb: ax88179_178a needs FLAG_SEND_ZLP
Misc:
- document some net.sctp.* sysctls
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEE6jPA+I1ugmIBA4hXMUZtbf5SIrsFAmKrcx8ACgkQMUZtbf5S
IrsKjA/9Ho+cxnGAvx7ngQepqAU8RQDFy7sQoFHiGqs+jMeph/E81PM2QDBR9g9h
k/s7YRpLGuxWFT7KUJScNl0ZyPgSk5EHcqy202ToYyDQv+srLnh5bgbRykMF2Unc
D4mf63a2pNo9S0L1PmMz87p+XaWIwblqQ0wbl5F97e7eAWel+y7rPCBqR0lZ9Il7
w8rZp6iOVOhD495s1ikqOYUVCntepC9MQIo8iIE/WrREiOWmZNNbV8RzvuHRNQs6
j9eLsukKwTfekQbzR3SXbYxyjwRowAQ3bD5sEL3MuqflsxRpVm5lEqN0AuVlAo3C
IJZFSFqnusC4cSUYVdfWhYlx8om+uw4XKzfqQD/T7yobjoVA/Mmt/Uf7Mw6krR+g
bI+/bpgX7WpLYQNtBFAils5pY36pthN+zg9FuU0v7tNLgC3AmQqA8sRI/fRCVJFV
b1Wmk6Ldj1lCynX0KpzU6XSFGzP2Ht9CYReImiwvZbaABIoM14woHhRPrh8UGWIY
sdpLoR+XRyL/0N1W7l0FgbGm/zOaEbh8fo0ZGYHLukXPUby6osiV36frzjxOj/NO
DqNkPq4ajfWFvcWdqbfRKXwpLyM/Ki2WpQjvaNzDLOL74sDspr8wjnIOOLbuHv/8
NW6tcWwfIu9nkDJOpRedh+O2gj6FKdruobdKVgQd376J0kxWLv0=
=JSV9
-----END PGP SIGNATURE-----
Merge tag 'net-5.19-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Mostly driver fixes.
Current release - regressions:
- Revert "net: Add a second bind table hashed by port and address",
needs more work
- amd-xgbe: use platform_irq_count(), static setup of IRQ resources
had been removed from DT core
- dts: at91: ksz9477_evb: add phy-mode to fix port/phy validation
Current release - new code bugs:
- hns3: modify the ring param print info
Previous releases - always broken:
- axienet: make the 64b addressable DMA depends on 64b architectures
- iavf: fix issue with MAC address of VF shown as zero
- ice: fix PTP TX timestamp offset calculation
- usb: ax88179_178a needs FLAG_SEND_ZLP
Misc:
- document some net.sctp.* sysctls"
* tag 'net-5.19-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (31 commits)
net: axienet: add missing error return code in axienet_probe()
Revert "net: Add a second bind table hashed by port and address"
net: ax25: Fix deadlock caused by skb_recv_datagram in ax25_recvmsg
net: usb: ax88179_178a needs FLAG_SEND_ZLP
MAINTAINERS: add include/dt-bindings/net to NETWORKING DRIVERS
ARM: dts: at91: ksz9477_evb: fix port/phy validation
net: bgmac: Fix an erroneous kfree() in bgmac_remove()
ice: Fix memory corruption in VF driver
ice: Fix queue config fail handling
ice: Sync VLAN filtering features for DVM
ice: Fix PTP TX timestamp offset calculation
mlxsw: spectrum_cnt: Reorder counter pools
docs: networking: phy: Fix a typo
amd-xgbe: Use platform_irq_count()
octeontx2-vf: Add support for adaptive interrupt coalescing
xilinx: Fix build on x86.
net: axienet: Use iowrite64 to write all 64b descriptor pointers
net: axienet: make the 64b addresable DMA depends on 64b archectures
net: hns3: fix tm port shapping of fibre port is incorrect after driver initialization
net: hns3: fix PF rss size initialization bug
...
It should return error code in error path in axienet_probe().
Fixes: 00be43a74c ("net: axienet: make the 64b addresable DMA depends on 64b archectures")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220616062917.3601-1-yangyingliang@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a handler of the XDP_REDIRECT return code from a XDP program. The
packets will be flushed at the end of each RX/CQ NAPI poll cycle.
ndo_xdp_xmit() is implemented by sharing the code in mana_xdp_tx().
Ethtool per queue counters are added for XDP redirect and xmit operations.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This minimal PF driver runs on bare metal.
Currently Ethernet TX/RX works. SR-IOV management is not supported yet.
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Co-developed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Some bootloader may set the force speed regs even if the actual
interface should use autonegotiation between PCS and PHY.
This cause the complete malfuction of the interface.
To fix this correctly reset the force speed regs if a fixed-link is not
defined in the DTS. With a fixed-link node correctly configure the
forced speed regs to handle any misconfiguration by the bootloader.
Reported-by: Mark Mentovai <mark@moxienet.com>
Co-developed-by: Mark Mentovai <mark@moxienet.com>
Signed-off-by: Mark Mentovai <mark@moxienet.com>
Signed-off-by: Christian 'Ansuel' Marangi <ansuelsmth@gmail.com>
Link: https://lore.kernel.org/r/20220614112228.1998-2-ansuelsmth@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The different gmacid require different configuration based on the soc
and on the gmac id. Add these missing configuration taken from the
original driver.
Signed-off-by: Christian 'Ansuel' Marangi <ansuelsmth@gmail.com>
Link: https://lore.kernel.org/r/20220614112228.1998-1-ansuelsmth@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This patch adds use of KBUILD_MODNAME as defined by the build system,
replacing the definition and use of a custom-defined name.
Signed-off-by: David Thompson <davthompson@nvidia.com>
Signed-off-by: Asmaa Mnebhi <asmaa@nvidia.com>
Link: https://lore.kernel.org/r/20220614212602.28061-1-davthompson@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Two fixes for rc1 PR.
BR, Jarkko
-----BEGIN PGP SIGNATURE-----
iIgEABYIADAWIQRE6pSOnaBC00OEHEIaerohdGur0gUCYqoqzBIcamFya2tvQGtl
cm5lbC5vcmcACgkQGnq6IXRrq9I3ngD/ZnreuHUG82mz8mLwiTx+cLF+4b4rGgBi
iOJUCx38KSYBALhk2ipFWJ7lCBoeokysx9S7bYVEKwQepn9jutMzmyUP
=/OV9
-----END PGP SIGNATURE-----
Merge tag 'tpmdd-next-v5.19-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/jarkko/linux-tpmdd
Pull tpm fixes from Jarkko Sakkinen:
"Two fixes for this merge window"
* tag 'tpmdd-next-v5.19-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/jarkko/linux-tpmdd:
certs: fix and refactor CONFIG_SYSTEM_BLACKLIST_HASH_LIST build
certs/blacklist_hashes.c: fix const confusion in certs blacklist
Commit addf466389 ("certs: Check that builtin blacklist hashes are
valid") was applied 8 months after the submission.
In the meantime, the base code had been removed by commit b8c96a6b46
("certs: simplify $(srctree)/ handling and remove config_filename
macro").
Fix the Makefile.
Create a local copy of $(CONFIG_SYSTEM_BLACKLIST_HASH_LIST). It is
included from certs/blacklist_hashes.c and also works as a timestamp.
Send error messages from check-blacklist-hashes.awk to stderr instead
of stdout.
Fixes: addf466389 ("certs: Check that builtin blacklist hashes are valid")
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Reviewed-by: Mickaël Salaün <mic@linux.microsoft.com>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
This file fails to compile as follows:
CC certs/blacklist_hashes.o
certs/blacklist_hashes.c:4:1: error: ignoring attribute ‘section (".init.data")’ because it conflicts with previous ‘section (".init.rodata")’ [-Werror=attributes]
4 | const char __initdata *const blacklist_hashes[] = {
| ^~~~~
In file included from certs/blacklist_hashes.c:2:
certs/blacklist.h:5:38: note: previous declaration here
5 | extern const char __initconst *const blacklist_hashes[];
| ^~~~~~~~~~~~~~~~
Apply the same fix as commit 2be04df566 ("certs/blacklist_nohashes.c:
fix const confusion in certs blacklist").
Fixes: 734114f878 ("KEYS: Add a system blacklist keyring")
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Reviewed-by: Mickaël Salaün <mic@linux.microsoft.com>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQRAhzRXHqcMeLMyaSiRxhvAZXjcogUCYqmpKwAKCRCRxhvAZXjc
ogvLAQCsgqKYjmqx1s9ta8PXH9qiTWLQh1/s3ONCAvSBe0rYRAD9HPwbUoxguqxr
T2RzjuX2+rqzA5qTErjQqVEftn7DgAo=
=+P6m
-----END PGP SIGNATURE-----
Merge tag 'fs.fixes.v5.19-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux
Pull vfs idmapping fix from Christian Brauner:
"This fixes an issue where we fail to change the group of a file when
the caller owns the file and is a member of the group to change to.
This is only relevant on idmapped mounts.
There's a detailed description in the commit message and regression
tests have been added to xfstests"
* tag 'fs.fixes.v5.19-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux:
fs: account for group membership
Allow mdb entries to be forwarded to CPU and be switched at the same
time. Only remove entry when no port and the CPU isn't part of the group
anymore.
Signed-off-by: Casper Andersson <casper.casan@gmail.com>
Acked-by: Steen Hegelund <Steen.Hegelund@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The skb_recv_datagram() in ax25_recvmsg() will hold lock_sock
and block until it receives a packet from the remote. If the client
doesn`t connect to server and calls read() directly, it will not
receive any packets forever. As a result, the deadlock will happen.
The fail log caused by deadlock is shown below:
[ 369.606973] INFO: task ax25_deadlock:157 blocked for more than 245 seconds.
[ 369.608919] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 369.613058] Call Trace:
[ 369.613315] <TASK>
[ 369.614072] __schedule+0x2f9/0xb20
[ 369.615029] schedule+0x49/0xb0
[ 369.615734] __lock_sock+0x92/0x100
[ 369.616763] ? destroy_sched_domains_rcu+0x20/0x20
[ 369.617941] lock_sock_nested+0x6e/0x70
[ 369.618809] ax25_bind+0xaa/0x210
[ 369.619736] __sys_bind+0xca/0xf0
[ 369.620039] ? do_futex+0xae/0x1b0
[ 369.620387] ? __x64_sys_futex+0x7c/0x1c0
[ 369.620601] ? fpregs_assert_state_consistent+0x19/0x40
[ 369.620613] __x64_sys_bind+0x11/0x20
[ 369.621791] do_syscall_64+0x3b/0x90
[ 369.622423] entry_SYSCALL_64_after_hwframe+0x46/0xb0
[ 369.623319] RIP: 0033:0x7f43c8aa8af7
[ 369.624301] RSP: 002b:00007f43c8197ef8 EFLAGS: 00000246 ORIG_RAX: 0000000000000031
[ 369.625756] RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007f43c8aa8af7
[ 369.626724] RDX: 0000000000000010 RSI: 000055768e2021d0 RDI: 0000000000000005
[ 369.628569] RBP: 00007f43c8197f00 R08: 0000000000000011 R09: 00007f43c8198700
[ 369.630208] R10: 0000000000000000 R11: 0000000000000246 R12: 00007fff845e6afe
[ 369.632240] R13: 00007fff845e6aff R14: 00007f43c8197fc0 R15: 00007f43c8198700
This patch replaces skb_recv_datagram() with an open-coded variant of it
releasing the socket lock before the __skb_wait_for_more_packets() call
and re-acquiring it after such call in order that other functions that
need socket lock could be executed.
what's more, the socket lock will be released only when recvmsg() will
block and that should produce nicer overall behavior.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Suggested-by: Thomas Osterried <thomas@osterried.de>
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Reported-by: Thomas Habets <thomas@@habets.se>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
napi_build_skb() reuses NAPI skbuff_head cache in order to save some
cycles on freeing/allocating skbuff_heads on every new Rx or completed
Tx.
Use napi_consume_skb() to feed the cache with skbuff_heads of completed
Tx so it's never empty.
Signed-off-by: Sieng Piaw Liew <liew.s.piaw@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NAPI cache skb_count is being checked twice without condition. Change to
checking the second time only if the first check is run.
Signed-off-by: Sieng Piaw Liew <liew.s.piaw@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding mdb entries on disabled ports allows you to do setup before
accepting any traffic, avoiding any time where the port is not in the
multicast group.
Signed-off-by: Casper Andersson <casper.casan@gmail.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The extra byte inserted by usbnet.c when
(length % dev->maxpacket == 0) is causing problems to device.
This patch sets FLAG_SEND_ZLP to avoid this.
Tested with: 0b95:1790 ASIX Electronics Corp. AX88179 Gigabit Ethernet
Problems observed:
======================================================================
1) Using ssh/sshfs. The remote sshd daemon can abort with the message:
"message authentication code incorrect"
This happens because the tcp message sent is corrupted during the
USB "Bulk out". The device calculate the tcp checksum and send a
valid tcp message to the remote sshd. Then the encryption detects
the error and aborts.
2) NETDEV WATCHDOG: ... (ax88179_178a): transmit queue 0 timed out
3) Stop normal work without any log message.
The "Bulk in" continue receiving packets normally.
The host sends "Bulk out" and the device responds with -ECONNRESET.
(The netusb.c code tx_complete ignore -ECONNRESET)
Under normal conditions these errors take days to happen and in
intense usage take hours.
A test with ping gives packet loss, showing that something is wrong:
ping -4 -s 462 {destination} # 462 = 512 - 42 - 8
Not all packets fail.
My guess is that the device tries to find another packet starting
at the extra byte and will fail or not depending on the next
bytes (old buffer content).
======================================================================
Signed-off-by: Jose Alonso <joalonsof@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the capability to map non-linear xdp frames in XDP_TX and ndo_xdp_xmit
callback.
Tested-by: Sarkar Tirthendu <tirthendu.sarkar@intel.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Tested-by: George Kuruvinakunnel <george.kuruvinakunnel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
phydev->port was not set and always reported as PORT_TP.
Set phydev->port according to inserted SFP module.
Signed-off-by: Ivan Bornyakov <i.bornyakov@metrotek.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add basic description for the xilinx emaclite driver DT bindings.
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
