Missing _SDD is not an error. Don't treat it as one.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Split sata_fsl_softreset() into hard and soft resets to make
error-handling more efficient & device and PMP detection more
reliable.
Also includes fix for PMP support, driver tested with Sil3726,
Sil4726 & Exar PMP controllers.
[AV: Also fixes resuming from deep sleep on MPC8315 CPUs]
Signed-off-by: Jiang Yutang <b14898@freescale.com>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Just remove redundant device ID for VIA VT8261.
The device ID 0x9000 and 0x9040 are redundant (for VT8261).
The 0x9040 is reserved for other usage.
Signed-off-by: Joseph Chan <josephchan@via.com.tw>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
In each case, if the NULL test on qc is needed, then the derefernce
should be after the NULL test.
A simplified version of the semantic match that detects this problem is as
follows (http://coccinelle.lip6.fr/):
// <smpl>
@match exists@
expression x, E;
identifier fld;
@@
* x->fld
... when != \(x = E\|&x\)
* x == NULL
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Like the Asus M2A-VM, MSI's K9A2 Platinum (MS-7376) can also support 64bit
DMA. It is a new enough board that all the BIOS releases work correctly with
64bit DMA enabled.
Signed-off-by: Mark Nelson <mdnelson8@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Use excl_link when non NCQ commands are defered, to be sure they are processed
as soon as outstanding commands are completed. It prevents some commands to be
defered indifinitely when using a port multiplier.
Signed-off-by: Gwendal Grignou <gwendal@google.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The SC1200 needs a NULL terminator or it may cause a crash on boot.
Bug #14227
Also correct a bogus comment as the driver had serializing added so can run
dual port.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
When an internal command fails, it should be failed directly without
invoking EH. In the original implemetation, this was accomplished by
letting internal command bypass failure handling in ata_qc_complete().
However, later changes added post-successful-completion handling to
that code path and the success path is no longer adequate as internal
command failure path. One of the visible problems is that internal
command failure due to timeout or other freeze conditions would
spuriously trigger WARN_ON_ONCE() in the success path.
This patch updates failure path such that internal command failure
handling is contained there.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Commit 842faa6c1a fixed error handling
during attach by not committing detected device class to dev->class
while attaching a new device. However, this change missed the PMP
class check in the configuration loop causing a new PMP device to go
through ata_dev_configure() as if it were an ATA or ATAPI device.
As PMP device doesn't have a regular IDENTIFY data, this makes
ata_dev_configure() tries to configure a PMP device using an invalid
data. For the most part, it wasn't too harmful and went unnoticed but
this ends up clearing dev->flags which may have ATA_DFLAG_AN set by
sata_pmp_attach(). This means that SATA_PMP_FEAT_NOTIFY ends up being
disabled on PMPs and on PMPs which honor the flag breaks hotplug
support.
This problem was discovered and reported by Ethan Hsiao.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Ethan Hsiao <ethanhsiao@jmicron.com>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
prereset doesn't bring link online if hardreset is about to happen and
nv_hardreset() may skip if conditions are not right so softreset may
be entered with non-working link status if the system firmware didn't
bring it up before entering OS code which can happen during resume.
This patch makes nv_hardreset() to bring up the link if it's skipping
reset.
This bug was reported by frodone@gmail.com in the following bug entry.
http://bugzilla.kernel.org/show_bug.cgi?id=14329
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: frodone@gmail.com
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix the VT6330 issue, it's because the rev_max of VT6330 exceeds 0x2f.
The VT6415 and VT6330 share the same device ID.
Signed-off-by: Joseph Chan <josephchan@via.com.tw>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Commit f80ae7e45a
ahci: filter FPDMA non-zero offset enable for Aspire 3810T
breaks the current git build for configurations that don't define
CONFIG_ATA_ACPI.
This adds an ifdef wrapper to ahci_gtf_filter_workaround.
Signed-off-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* use 8 clk setting for active clocks == 7 (was 12 clk)
* use 12 clk setting for active clocks > 12 (was 8 clk)
* do 66MHz bus fixup before mapping active clocks
* fix setup of PIO command timings
Acked-by: Jung-Ik (John) Lee <jilee@google.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
MWDMA modes are not supported by this driver currently.
Acked-by: Jung-Ik (John) Lee <jilee@google.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
While trying to work around spurious detection retries for
non-existent devices on slave links, commit
816ab89782 incorrectly added link
offline check logic before ata_eh_thaw() was called. This means that
if an occupied link goes down briefly at the time that offline check
was performed, device class will be cleared to ATA_DEV_NONE and libata
wouldn't retry thus failing detection of the device.
The offline check should be done after the port is thawed together
with online check so that such link glitches can be detected by the
interrupt handler and handled properly.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Tim Blechmann <tim@klingt.org>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Curiously, Aspire 3810T issues many SATA feature enable commands via
_GTF, of which one is invalid and another is not supported by the
drive. In the process, it also enables FPDMA non-zero offset.
However, the feature also needs to be supported and enabled from the
controller and it's wrong to enable it from _GTF unless the controller
can do it by default.
Currently, this ends up enabling FPDMA non-zero offset only on the
drive side leading to NCQ command failures and eventual disabling of
NCQ. This patch makes libata filter out FPDMA non-zero offset enable
for the machine.
This was reported by Marcus Meissner in bnc#522790.
https://bugzilla.novell.com/show_bug.cgi?id=522790
Reported-by: Marcus Meissner <meissner@novell.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add ->gtf_filter to ata_device and set it to ata_acpi_gtf_filter when
initializing ata_link. This is to allow quirks which apply different
gtf filters.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Currently libata-acpi can only filter DIPM among SATA feature enables
via _GTF. This patch adds the capability to filter out FPDMA non-zero
offset, in-order guarantee and auto-activation.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
We're about to add more SATA_* and ATA_ACPI_FILTER_* constants.
Reformat them in preparation.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Update the AHCI driver to display all of the HBA capabilities defined in the
AHCI 1.3 specification. Some of these are in a new CAP2 (HBA Capabilities
Extended) register which is only defined on AHCI 1.2 or later. The spec says
that undefined registers should always return 0 on read, but to be safe we
assume a value of 0 unless the controller reports AHCI version 1.2 or later.
The value can also be retrieved through sysfs as with the existing capability
field.
For example, on an Intel Ibex Peak (PCH) controller:
ahci 0000:00:1f.2: flags: 64bit ncq sntf stag pm led clo pmp pio slum part ems
sxs apst
We don't do anything special with the new flags yet.
Also, change the code that displays the flags to use the same bit enumerations
that are used to control actual operation.
Signed-off-by: Robert Hancock <hancockrwd@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
something-bility is spelled as something-blity
so a grep for 'blit' would find these lines
I broke this one out from the rest as it actually changes
the output of a kernel message - so it could in theory
change the behavior of tools that parse that ouput
Signed-off-by: Dirk Hohndel <hohndel@infradead.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Till now only one board, ASUS M2A-VM, can do 64bit dma with recent
BIOSen. Enabling 64bit DMA by default already broke three boards.
Enabling 64bit DMA isn't worth these regressions. Disable 64bit DMA
by default and enable it only on boards which are known to work.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Gabriele Balducci <balducci@units.it>
Reported-by: maierp@informatik.tu-muenchen.de
Cc: Shane Huang <shane.huang@amd.com>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This is a new pata driver for ARTOP 867X 64bit 4-channel UDMA133 ATA ctrls.
Based on the Atp867 data sheet rev 1.2, Acard, and in part on early ide codes
from Eric Uhrhane <ericu@google.com>.
Signed-off-by: John(Jung-Ik) Lee <jilee@google.com>
Reviewed-by: Grant Grundler <grundler@google.com>
Reviewed-by: Gwendal Gringo <gwendal@google.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
On a Compaq Presario V3000 laptop (NVIDIA MCP51 chipset), pata_amd selects
PIO0 mode for the PATA DVD-RAM drive instead of MWDMA2 which it supports:
ata4.00: ATAPI: HL-DT-ST DVDRAM GSA-4084N, KQ09, max MWDMA2
ata4: nv_mode_filter: 0x39f&0x7001->0x1, BIOS=0x0 (0x0) ACPI=0x7001 (60:600:0x11)
ata4.00: configured for PIO0
For some reason, the BIOS-set UDMA configuration returns 0 and the ACPI _GTM
reports that UDMA2 and PIO0 are enabled. This causes nv_mode_filter to end up
allowing only PIO0 and UDMA0-2. Since the drive doesn't support UDMA we end up
using PIO0.
Since the controllers should always support PIO4, MWDMA2 and UDMA2 regardless
of what cable type is used, let's make sure we don't filter out these modes
regardless of what wacky settings the BIOS is using.
Signed-off-by: Robert Hancock <hancockrwd@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
sata_promise's reset code has deviated quite a bit from
the Promise reference driver's, and it has been observed
to fail to recover from errors in some cases.
This patch thus updates the reset code to more closely
match the reference driver:
- soft reset (pdc_reset_port):
* wait for ATA engine to not be in packet command mode
(2nd gen only)
* write reset bit in PDC_CTLSTAT before the first read
in the loop
* for 2nd gen SATA follow up with FPDMA reset and clearing
error status registers
- hard reset (pdc_sata_hardreset):
* wait for ATA engine to not be in packet command mode
(2nd gen only)
* reset ATA engine via the PCI control register
* Tejun's change to use non-waiting hardreset + follow-up SRST
I'm not changing the hotplug mask bits since they are taken care
of by sata_promise's ->freeze() and ->thaw() operations. And I'm
not writing the PMP port # because that's always zero (for now).
Tested here on various controllers. In particular, one disk
which used to timeout and fail to recover from certain hdparm
and smartmonctl commands now works nicely.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
1st generation Promise SATA chips are prone to generating spurious
hotplug events which can disrupt normal operation. This has been
observed on 20376 and 20378 chips. This patch thus disables hotplug
support on 1st gen chips while leaving it enabled for 2nd gen chips.
The pdc_sata_hotplug_offset() function becomes redundant so it is
removed.
Tested on 1st gen 20376 and 20378 mainboard chips and on a 2nd gen
SATA300 PCI card.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Tested-by: Kurt Roeckx <kurt@roeckx.be>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Commit 54c38444fa makes libata abort qcs
after the port is frozen. This is necessary to guarantee that TF
registers are accessed after the DMA engine is shutdown after an
error. However, this triggers WARN_ON_ONCE() check in
ata_qc_complete() spuriously. Move WARN_ON_ONCE() downwards such that
failing commands while frozen doesn't trigger it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Commit a5bfc4714b dropped explicit
pci_intx() manipulation from ahci because it seemed unnecessary and
ahci doesn't seem to be the right place to be tweaking it if it were.
This was largely okay but there are exceptions. There was one on an
embedded platform which was fixed via firmware and now bko#14124
reports it on a HP DL320.
http://bugzilla.kernel.org/show_bug.cgi?id=14124
I still think this isn't something libata drivers should be caring
about (the only ones which are calling pci_intx() explicitly are
libata ones and one other driver) but for now reverting the change
seems to be the right thing to do.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Thomas Jarosch <thomas.jarosch@intra2net.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch refines ahci_kick_engine() after discussion with Tejun about
FBS(FIS-based switching) support preparation:
a. Kill @force_restart and always kick the engine. The only case where
@force_restart is zero is when it's called from ahci_p5wdh_hardreset()
Actually at that point, BSY is pretty much guaranteed to be set.
b. If PMP is attached, ignore busy and always do CLO. (AHCI-1.3 9.2)
Signed-off-by: Shane Huang <shane.huang@amd.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Use the function resource_size, which reduces the chance of introducing
off-by-one errors in calculating the resource size.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
struct resource *res;
@@
- (res->end - res->start) + 1
+ resource_size(res)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix for non-ncq & ncq commands causing timeouts when both are issued
simultaneously to the same device.
Signed-off-by: Ashish Kalra <Ashish.Kalra@freescale.com>
[fixed to be actual compileable C code -jg]
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This small patch is just adding the information for PMP spec 1.2
Signed-off-by: Shane Huang <shane.huang@amd.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ata_tf_read_block() has off-by-one error when converting CHS address
to LBA. The bug isn't very visible because ata_tf_read_block() is
used only when generating sense data for a failed RW command and CHS
addressing isn't used too often these days.
This problem was spotted by Atsushi Nemoto.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
It turns out ASUS M2A-VM isn't the only one with the 32bit DMA
problem. Make ahci_asus_m2a_vm_32bit_only() more generic using the
new dmi_get_date() and rename it to ahci_sb600_32bit_only(). Cut off
date is now pointed to by dmi_system_id->driver_data in "yyyymmdd"
format and it's now also allowed to be omitted.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Sandor Bodo-Merle <sbodomerle@gmail.com>
Cc: Shane Huang <shane.huang@amd.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
There are cases where full date information is required instead of
just the year. Add month and day parsing to dmi_get_year() and rename
it to dmi_get_date().
As the original function only required '/' followed by any number of
parseable characters at the end of the string, keep that behavior to
avoid upsetting existing users.
The new function takes dates of format [mm[/dd]]/yy[yy]. Year, month
and date are checked to be in the ranges of [1-9999], [1-12] and
[1-31] respectively and any invalid or out-of-range component is
returned as zero.
The dummy implementation is updated accordingly but the return value
is updated to indicate field not found which is consistent with how
other dummy functions behave.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ata_scsi_pass_thru() was checking for input sanity and disallowed
commands while initializaing qc from scmd. TPM filtering was added
right after protocol check at which point tf wasn't initialized
properly. This means that TPM filtering has never really worked.
This patch fixes the bug by reorganizing ata_scsi_pass_thru() such
that qc is fully initialized before checking for invalid conditions
which is way less error prone.
Discovered while Thilo-Alexander Ginkel was trying debug patches for
bko#13416.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Thilo-Alexander Ginkel <thilo@ginkel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
During introduction of slave_link, sata_sis slipped through the crack
and left with ad-hoc merged SCR access. As SCR status was shared for
both the master and slave devices, when only one of the device is
online, libata EH would think both are online but would only get valid
device signature for the actually present one, which in turn trigger
the probing safety net mechanism and make EH retry causing large delay
during boot. This patch converts sata_sis to slave_link mechanism.
This bug was reported by TAXI in bko#14075.
http://bugzilla.kernel.org/show_bug.cgi?id=14075
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: TAXI <taxi@a-city.de>
Cc: Uwe Koziolek <uwe.koziolek@gmx.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The sil24 hardware has a built-in list of commands and associated protocols
that gets used by default to decide how to handle a given command. However,
if the command is not known to the controller then it presumably assumes it to
be a non-data command which then causes protocol mismatch errors if the device
ends up requesting data transfer. The new DATA SET MANAGEMENT - Trim command
causes this issue since it's a DMA data-out command.
Since we should always know best what protocol the command should be using,
let's just set the override flag to inform the controller what protocol to use
for all non-ATAPI commands with data transfer.
Signed-off-by: Robert Hancock <hancockrwd@gmail.com>
Tested-by: Mark Lord <liml@rtr.ca>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
AHCI exports various capability bits that may be of interest to userspace
such as whether the BIOS claims a port is hotpluggable or eSATA. Providing
these via sysfs along with the version of the AHCI spec implemented by
the host allows userspace to make policy decisions for things like ALPM.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Now that the SCSI disk driver correctly handles non-rotational devices
we can move setting the queue flag to SCSI.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
