Commit Graph

5 Commits

Author SHA1 Message Date
Fabio Estevam
042f6d9826 ARM: dts: imx53-qsb: Provide the TVE DAC regulators
On imx53-qsb the TVE DAC regulator comes from:

- LDO7 on the board with the Dialog DA9052 PMIC
- VDAC on the board with the MC34708 PMIC

Pass them in the 'dac-supply' node.

While at it, remove the 'regulator-always-on/regulator-boot-on'
properties as the TVE driver will properly handle it.

Tested on a imx53-qsb board with a Dialog DA9052 PMIC.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2017-01-10 11:05:56 +08:00
Lucas Stach
e1ffceb078 ARM: imx53: qsrb: fix PMIC interrupt level
The MC34708 PMIC interrupt level is active high, but was set to
active low in the devicetree, probably as a result of a copy and
paste error from the QSB board.

This caused IRQ storms and led to the kernel disabling the PMIC
interrupt.

Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2015-09-17 08:54:13 +08:00
Lucas Stach
fb00ff4c30 ARM: dts: imx53-qsb: select open-drain mode for i2c1 pads
Both imx53-qsb and imx53-qsrb don't have external pull-up resistors
on the I2C1 SCL and SDA lines populated. Select open-drain mode and
enable the internal pull-up for both.

Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2015-07-15 10:20:36 +08:00
Fabio Estevam
090727b880 ARM: dts: imx53-qsrb: Fix suspend/resume
The following error is seen after a suspend/resume cycle on a mx53qsb with a
MC34708 PMIC:

root@freescale /$ echo mem > /sys/power/state
[   32.630592] PM: Syncing filesystems ... done.
[   32.643924] Freezing user space processes ... (elapsed 0.001 seconds) done.
[   32.652384] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
[   32.679156] PM: suspend of devices complete after 13.113 msecs
[   32.685128] PM: suspend devices took 0.030 seconds
[   32.696109] PM: late suspend of devices complete after 6.133 msecs
[   33.313032] mc13xxx 0-0008: Failed to read IRQ status: -110
[   33.322009] PM: noirq suspend of devices complete after 619.667 msecs
[   33.328544] Disabling non-boot CPUs ...
[   33.335031] PM: noirq resume of devices complete after 2.352 msecs
[   33.842940] mc13xxx 0-0008: Failed to read IRQ status: -110
[   33.976095] [sched_delayed] sched: RT throttling activated
[   33.984804] PM: early resume of devices complete after 642.642 msecs
[   34.352954] mc13xxx 0-0008: Failed to read IRQ status: -110
[   34.862910] mc13xxx 0-0008: Failed to read IRQ status: -110
[   34.996595] PM: resume of devices complete after 1005.367 msecs
[   35.372925] mc13xxx 0-0008: Failed to read IRQ status: -110
[   35.882911] mc13xxx 0-0008: Failed to read IRQ status: -110
[   35.955707] PM: resume devices took 1.970 seconds
[   35.960445] Restarting tasks ... done.
[   35.993386] fec 63fec000.ethernet eth0: Link is Down
[   36.392980] mc13xxx 0-0008: Failed to read IRQ status: -110
[   36.902908] mc13xxx 0-0008: Failed to read IRQ status: -110
[   36.953036] ata1: SATA link down (SStatus 0 SControl 300)
[   37.412922] mc13xxx 0-0008: Failed to read IRQ status: -110
[   37.922906] mc13xxx 0-0008: Failed to read IRQ status: -110
[   37.993379] fec 63fec000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx
[   38.432938] mc13xxx 0-0008: Failed to read IRQ status: -110
[   38.942920] mc13xxx 0-0008: Failed to read IRQ status: -110
[   39.452933] mc13xxx 0-0008: Failed to read IRQ status: -110

(flood of this error message continues forever)

Commit 5169df8be0 ("ARM: dts: i.MX53: add support for MCIMX53-START-R")
missed to configure the IOMUX for the PMIC IRQ pin.

Configure the PMIC IRQ pin so that the suspend/resume sequence behaves cleanly
as expected.

Cc: <stable@vger.kernel.org> # 3.16
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
2014-08-19 22:02:25 +08:00
Steffen Trumtrar
5169df8be0 ARM: dts: i.MX53: add support for MCIMX53-START-R
The "Start-R QSB" has a different PMIC than the older "Start QSB".
Add a new devicetree for the Start-R.
They both could use the same DT, as both PMICs (the dialog and the mc34708)
have different i2c addresses and could coexist in the same DT without any
errors. But once phandles are used, this will get messy.

The pmic nodes are based on an earlier patch

	[PATCH] arm: imx53-qsb: Add Ripley driver DT nodes

from

	Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>

which apparently got lost/abandoned.

I added phandles/newlines and changed the node name from ripley to mc34708.

Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2014-02-09 21:33:43 +08:00