It is not allowed to call kfree_skb() from hardware interrupt
context or with hardware interrupts being disabled.
So replace kfree_skb() with dev_kfree_skb_irq() under
spin_lock_irqsave(). Compile tested only.
Fixes: baac6276c0 ("Bluetooth: btusb: handle mSBC audio over USB Endpoints")
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The quirks table was named "blacklist_table" which isn't a good
description for that table as devices detected using it weren't ignored
by the driver.
Rename the table to match what it actually does.
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Add support for the WCN7850 Bluetooth chipset.
Tested on the SM8550 QRD platform.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Use switch/case to handle soc type specific behaviour,
the permit dropping the qca_is_xxx() inline functions
and make the code clearer and easier to update for new
SoCs.
Suggested-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Suggested-by: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This improves the inband IR command handling for NXP BT chipsets.
When the IR vendor command is received, the driver injects a HW
error event, which causes a reset sequence in hci_error_reset().
The vendor IR command is sent to the controller while hci dev
is been closed, and FW is re-downloaded when nxp_setup() is
called during hci_dev_do_open().
The HCI_SETUP flag is set in nxp_hw_err() to make sure that
nxp_setup() is been called during hci_dev_do_open().
This also makes the nxp_setup() and power save functions more
generic.
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This adds support for NXP IW624 chipset in btnxpuart driver
by adding FW name and bootloader signature. Based on the
loader version bits 7:6 of the bootloader signature, the
driver can choose between selecting secure and non-secure
FW files.
For cmd5 payload during FW download, this chip has addresses
of few registers offset by 1, so added boot_reg_offset to
handle the chip specific offset.
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This removes the unnecessary check for CTS low after FW download.
After FW download is complete, the CTS line is already seen low.
It becomes high after 2 msec, and low again after FW initialization
is complete.
This makes the current check for CTS low redundant.
This removes the wait for CTS low section and increase delay to
1200msec instead, which is sufficiant for all NXP chipsets to
initialize FW.
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
In this commit, prefer to load FW v2 if available. Fallback to FW v1
otherwise. This behavior is only for RTL8852C.
Fixes: 9a24ce5e29 ("Bluetooth: btrtl: Firmware format v2 support")
Cc: stable@vger.kernel.org
Suggested-by: Juerg Haefliger <juerg.haefliger@canonical.com>
Tested-by: Hilda Wu <hildawu@realtek.com>
Signed-off-by: Max Chou <max.chou@realtek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
btusb_recv_event_intel is specific to Intel controllers therefore it
shall be placed inside btintel.c so btusb don't have a mix of vendor
specific code with the generic parts.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Add support for the Bluetooth chip codenamed APACHE which is part of
WCN3988.
The firmware for this chip has a slightly different naming scheme
compared to most others. For ROM Version 0x0200 we need to use
apbtfw10.tlv + apnv10.bin and for ROM version 0x201 apbtfw11.tlv +
apnv11.bin
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This adds support for NXP AW693 chipset in btnxpuart driver
by adding FW name and bootloader signature. Based on the
loader version bits 7:6 of the bootloader signature, the
driver can choose between selecting secure and non-secure
FW files.
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
in nokia_bluetooth_serdev_probe(), check the return value of
clk_prepare_enable() and return the error code if
clk_prepare_enable() returns an unexpected value.
Fixes: 7bb318680e ("Bluetooth: add nokia driver")
Signed-off-by: Yuanjun Gong <ruc_gongyuanjun@163.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The BCM43430A1 has a default MAC address of AA:AA:AA:AA:AA:AA.
Although, unlike some other entries, this does not include the
chip name, it is clearly not a real address. This was found in
AzureWave AW-NB197SM and AW-NM372SM modules.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This patch implement function .coredump() and dmp_hdr() in btusb
driver for MediaTek controller. FW core dump was triggered by FW
specific event to show something unexpected happened in the controller.
The driver would be responsible for collecting and uploading the device
core dump pieces in hci driver using core dump API. Once we finished
the whole process, the driver would reset the controller to recover the
kind of fatal error.
Co-developed-by: Chris Lu <chris.lu@mediatek.com>
Signed-off-by: Chris Lu <chris.lu@mediatek.com>
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Jing Cai <jing.cai@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Introduce btmtk_reset_work which can be called whenever the firmware abort,
HCI command timeout, other fatal error happen.
Co-developed-by: Chris Lu <chris.lu@mediatek.com>
Signed-off-by: Chris Lu <chris.lu@mediatek.com>
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Jing Cai <jing.cai@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Use readx_poll_timeout instead of open coding to poll the hardware reset
status until it is done.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Add printing firmware information part when driver loading firmware that
user can get mediatek bluetooth information.
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Chris Lu <chris.lu@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Add hardware variant(0x1c) for Gale Peak core (CNVi).
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
New Intel platforms supports reset of Bluetooth device via ACPI DSM
methods. The legacy reset mechanism via GPIO will be deprecated in
future. This patch checks the platform support for reset methods and if
supported uses the same instead of legacy GPIO toggling method.
ACPI firmware supports two types of reset method based on NIC card.
(Discrete or Integrated).
1. VSEC Type - Vendor Specific Extended Capability. Here BT_EN and
BT_IF_SELECT lines are driven by a register in PCH cluster. This
interface is supported on discrete BT solution.
2. WDISABLE2 - In this soluton, W_DISABLE2 pin in M.2 is connected to
physical GPIO from PCH. The DSM interface shall toggle this to recover
from error.
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Intercept debug exception events from QCA controller and put them into
a devcoredump using hci devcoredump APIs of hci_core
Signed-off-by: Sai Teja Aluvala <quic_saluvala@quicinc.com>
V2 -> V3:
---------
changed hci_coredump_qca function
V1 -> V2:
---------
Updated to work with the updated HCI devcoredump API.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This patch implements the hci_qca driver side .coredump() callback to
trigger a devcoredump via sysfs.
Signed-off-by: Sai Teja Aluvala <quic_saluvala@quicinc.com>
v2 -> V3:
--------
Updated commit text
v1 -> V2:
--------
Updated to work with the updated HCI devcoredump API.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The original code did not determine the length value of the HCI command
for drop fw even there's no parameter needed. In this commit, use struct
hci_command_hdr to manage opcode and length. It would be more regular and
more readable.
Suggested-by: Alex Lu <alex_lu@realsil.com.cn>
Signed-off-by: Max Chou <max.chou@realtek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Catch debug exception from controller and driver, and trigger a
devcoredump using hci devcoredump APIs. The debug exception data
will be parsed in userspace.
Signed-off-by: Alex Lu <alex_lu@realsil.com.cn>
Signed-off-by: Hilda Wu <hildawu@realtek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Commit c13380a555 ("Bluetooth: btusb: Do not require hardcoded
interface numbers") inadvertedly broke bluetooth on Intel Macbook 2014.
The intention was to keep behavior intact when BTUSB_IFNUM_2 is set and
otherwise allow any interface numbers. The problem is that the new logic
condition omits the case where bInterfaceNumber is 0.
Fix BTUSB_IFNUM_2 handling by allowing both interface number 0 and 2
when the flag is set.
Fixes: c13380a555 ("Bluetooth: btusb: Do not require hardcoded interface numbers")
Reported-by: John Holland <johnbholland@icloud.com>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=217651
Signed-off-by: Tomasz Moń <tomasz.mon@nordicsemi.no>
Tested-by: John Holland<johnbholland@icloud.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Current release - regressions:
- nvme-tcp: fix comma-related oops after sendpage changes
Current release - new code bugs:
- ptp: make max_phase_adjustment sysfs device attribute invisible
when not supported
Previous releases - regressions:
- sctp: fix potential deadlock on &net->sctp.addr_wq_lock
- mptcp:
- ensure subflow is unhashed before cleaning the backlog
- do not rely on implicit state check in mptcp_listen()
Previous releases - always broken:
- net: fix net_dev_start_xmit trace event vs skb_transport_offset()
- Bluetooth:
- fix use-bdaddr-property quirk
- L2CAP: fix multiple UaFs
- ISO: use hci_sync for setting CIG parameters
- hci_event: fix Set CIG Parameters error status handling
- hci_event: fix parsing of CIS Established Event
- MGMT: fix marking SCAN_RSP as not connectable
- wireguard: queuing: use saner cpu selection wrapping
- sched: act_ipt: various bug fixes for iptables <> TC interactions
- sched: act_pedit: add size check for TCA_PEDIT_PARMS_EX
- dsa: fixes for receiving PTP packets with 8021q and sja1105 tagging
- eth: sfc: fix null-deref in devlink port without MAE access
- eth: ibmvnic: do not reset dql stats on NON_FATAL err
Misc:
- xsk: honor SO_BINDTODEVICE on bind
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=9yzk
-----END PGP SIGNATURE-----
Merge tag 'net-6.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from bluetooth, bpf and wireguard.
Current release - regressions:
- nvme-tcp: fix comma-related oops after sendpage changes
Current release - new code bugs:
- ptp: make max_phase_adjustment sysfs device attribute invisible
when not supported
Previous releases - regressions:
- sctp: fix potential deadlock on &net->sctp.addr_wq_lock
- mptcp:
- ensure subflow is unhashed before cleaning the backlog
- do not rely on implicit state check in mptcp_listen()
Previous releases - always broken:
- net: fix net_dev_start_xmit trace event vs skb_transport_offset()
- Bluetooth:
- fix use-bdaddr-property quirk
- L2CAP: fix multiple UaFs
- ISO: use hci_sync for setting CIG parameters
- hci_event: fix Set CIG Parameters error status handling
- hci_event: fix parsing of CIS Established Event
- MGMT: fix marking SCAN_RSP as not connectable
- wireguard: queuing: use saner cpu selection wrapping
- sched: act_ipt: various bug fixes for iptables <> TC interactions
- sched: act_pedit: add size check for TCA_PEDIT_PARMS_EX
- dsa: fixes for receiving PTP packets with 8021q and sja1105 tagging
- eth: sfc: fix null-deref in devlink port without MAE access
- eth: ibmvnic: do not reset dql stats on NON_FATAL err
Misc:
- xsk: honor SO_BINDTODEVICE on bind"
* tag 'net-6.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (70 commits)
nfp: clean mc addresses in application firmware when closing port
selftests: mptcp: pm_nl_ctl: fix 32-bit support
selftests: mptcp: depend on SYN_COOKIES
selftests: mptcp: userspace_pm: report errors with 'remove' tests
selftests: mptcp: userspace_pm: use correct server port
selftests: mptcp: sockopt: return error if wrong mark
selftests: mptcp: sockopt: use 'iptables-legacy' if available
selftests: mptcp: connect: fail if nft supposed to work
mptcp: do not rely on implicit state check in mptcp_listen()
mptcp: ensure subflow is unhashed before cleaning the backlog
s390/qeth: Fix vipa deletion
octeontx-af: fix hardware timestamp configuration
net: dsa: sja1105: always enable the send_meta options
net: dsa: tag_sja1105: fix MAC DA patching from meta frames
net: Replace strlcpy with strscpy
pptp: Fix fib lookup calls.
mlxsw: spectrum_router: Fix an IS_ERR() vs NULL check
net/sched: act_pedit: Add size check for TCA_PEDIT_PARMS_EX
xsk: Honor SO_BINDTODEVICE on bind
ptp: Make max_phase_adjustment sysfs device attribute invisible when not supported
...
For virtio-net we were getting CPU stall warnings, and fixed it by
calling the scheduler: see f8bb510439 ("virtio_net: suppress cpu stall
when free_unused_bufs").
This driver is similar so theoretically the same logic applies.
Signed-off-by: Xianting Tian <xianting.tian@linux.alibaba.com>
Message-Id: <20230609131817.712867-4-xianting.tian@linux.alibaba.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Adding the device ID from the Asus Ally gets the bluetooth working
on the device.
Signed-off-by: Matthew Anderson <ruinairas1992@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A recent commit restored the original (and still documented) semantics
for the HCI_QUIRK_USE_BDADDR_PROPERTY quirk so that the device address
is considered invalid unless an address is provided by firmware.
This specifically means that this flag must only be set for devices with
invalid addresses, but the Broadcom driver has so far been setting this
flag unconditionally.
Fortunately the driver already checks for invalid addresses during setup
and sets the HCI_QUIRK_INVALID_BDADDR flag. Use this flag to indicate
when the address can be overridden by firmware (long term, this should
probably just always be allowed).
Fixes: 6945795bc8 ("Bluetooth: fix use-bdaddr-property quirk")
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/lkml/ecef83c8-497f-4011-607b-a63c24764867@samsung.com
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use le32_to_cpu for ver.soc_id to fix the following
sparse warning.
drivers/bluetooth/btqca.c:640:24: sparse: warning: restricted
__le32 degrades to integer
Signed-off-by: Min-Hua Chen <minhuadotchen@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add missing MODULE_FIRMWARE declarations for firmware referenced in
btrtl.c.
Signed-off-by: Dan Gora <dan.gora@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since commit 3e4be65eb8 ("Bluetooth: hci_qca: Add poweroff support
during hci down for wcn3990"), the setup callback which registers the
debugfs interface can be called multiple times.
This specifically leads to the following error when powering on the
controller:
debugfs: Directory 'ibs' with parent 'hci0' already present!
Add a driver flag to avoid trying to register the debugfs interface more
than once.
Fixes: 3e4be65eb8 ("Bluetooth: hci_qca: Add poweroff support during hci down for wcn3990")
Cc: stable@vger.kernel.org # 4.20
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This fixes the follwing compiler warning reported by kernel test robot:
drivers/bluetooth/btnxpuart.c:1332:34: warning: unused variable
'nxpuart_of_match_table' [-Wunused-const-variable]
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/oe-kbuild-all/202305161345.eClvTYQ9-lkp@intel.com/
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
WCN6855 will report memdump via ACL data or HCI event when
it get crashed, so we collect memdump to debug firmware.
Signed-off-by: Tim Jiang <quic_tjiang@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This enables flow control before checking for bootloader signature and
deciding whether FW download is needed or not. In case of V1 bootloader
chips w8987 and w8997, it is observed that if WLAN FW is downloaded first
and power save is enabled in wlan core, bootloader signatures are not
emitted by the BT core when the chip is put to sleep. As a result, the
driver skips FW download and subsequent HCI commands get timeout errors
in dmesg as shown below:
[ 112.898867] Bluetooth: hci0: Opcode 0x c03 failed: -110
[ 114.914865] Bluetooth: hci0: Setting baudrate failed (-110)
[ 116.930856] Bluetooth: hci0: Setting wake-up method failed (-110)
By enabling the flow control, the host enables its RTS pin, and an
interrupt in chip's UART peripheral causes the bootloader to wake up,
enabling the bootloader signatures, which then helps in downloading
the bluetooth FW file.
This changes all instances of 0/1 for serdev_device_set_flow_control()
to false/true.
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
