Update the defconfig files for 4xx boards. This also makes the mutli-board
defconfigs a bit more useful by enabling some of the more common modules.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This is a defconfig from Dave Jones and should be similar (if not
identical) to the fedora ppc32 defconfig. The intent is to cover all
cache coherent 6xx based chips and platforms as reasonable.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The defconfigs for Freescale 85xx and 86xx SOCs had bad choices for some
audio related options. In particular, OSS emulation should be enabled,
and the old ALSA API should be disabled.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The ULI "Super South Bridge" contains ISA bridge to the legacy
devices, such as Super IO mouse/keyboard/floppy disk controllers,
parallel port, i8259 interrupt controller and so on.
i8259 is disabled on the MPC8610HPCD, and other peripherals are not
traced out. So we use only RTC.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Adds a character driver for BSR support on IBM POWER systems including
Power5 and Power6. The BSR is an optional processor facility not currently
implemented by any other processors. It's primary purpose is fast large SMP
synchronization. More details on the BSR are in comments to the code which
follows. This patch adds BSR driver to pseries_defconfig.
Signed-off-by: Sonny Rao <sonnyrao@linux.vnet.ibm.com>
Signed-off-by: Joel Schopp <jschopp@austin.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Add support for the MPC8536 process and MPC8536DS reference board. The
MPC8536 is an e500v2 based SoC which eTSEC, USB, SATA, PCI, and PCIe.
The USB and SATA IP blocks are similiar to those on the PQ2 Pro SoCs and
thus use the same drivers.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
It adds the missing RTC node to tqm8548.dts and enables support for
I2C, DS1307 and LM75 in the default configuration.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This defconfig file is specific to Xilinx Virtex 5 FXT platform.
Signed-off-by: John Linn <john.linn@xilinx.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This enables CONFIG_ATA_SFF in the defconfigs that are intended to
work on a G5 powermac, i.e. g5_defconfig and ppc64_defconfig. Since
the support for the SATA cell in the K2 chipset is provided by the
sata_svw.c driver, and that depends on CONFIG_ATA_SFF, we need to turn
that and CONFIG_SATA_SVW back on so we can get to the hard disk on G5s.
Signed-off-by: Paul Mackerras <paulus@samba.org>
The Sam440ep is an high customizable general purpose mini-itx board,
based on the AMCC 440EP and with a LatticeXP FPGA onboard.
It's poduced by ACube Systems Srl (Bassano del Grappa, Italy),
http://www.acube-systems.biz.
Signed-off-by: Giuseppe Coviello <gicoviello@gmail.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Add support for the NOR flash found on the AMCC Taishan Board
and enable MTD support in the defconfig.
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This is patch adds board file, device tree, and defconfig for the new
board, made by Freescale Semiconductor Inc. and Logic Product Development.
Currently supported:
1. UEC{1,2,7,4};
2. I2C;
3. SPI;
4. NS16550 serial;
5. PCI and miniPCI;
6. Intel NOR StrataFlash X16 64Mbit PC28F640P30T85;
7. Graphics controller, Fujitsu MB86277.
Not supported in this patch:
1. StMICRO NAND512W3A2BN6E, 512 Mbit (supported with FSL UPM NAND driver);
2. FHCI USB (supported with FHCI driver).
3. QE Serial UCCs (tested to not work with ucc_uart driver, reason
unknown, yet);
4. ADC AD7843 (tested to work, but support via device tree depends on
major SPI rework, GPIO API, etc);
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds support for the TQM8548 modules from TQ-Components
GmbH (http://www.tqc.de).
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
MDIO-less PHYs should use CONFIG_FIXED_PHY driver and appropriate
fixed-link property in the device tree.
If not, ethernet will not work:
e0024520:03 not found
eth1: Could not attach to PHY
IP-Config: Failed to open eth1
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Update the defconfig for the Freescale MPC8610 HPCD board. Enable module
support. Disable support for all NICs except for the on-board ULI526x.
Enable support for the Freescale DIU driver. Increase the maximum zone order
to 12, so that the DIU driver can allocate physically-contiguous 5MB buffers.
Enable SYSV IPC and OSS plugin support, which are needed for some OSS apps.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Support for the C2K cPCI Single Board Computer from GEFanuc
(PowerPC MPC7448 with a Marvell MV64460 chipset).
All features of the board are not supported yet, but the board
boots, flash works, all Ethernet ports are working and PCI
devices are all found (USB and SATA on PCI1 do not work yet).
Part 4 of 5: this is the default config for the board. In this
configuration the kernel is going to try to boot from MTD
partition 3 on the NOR flash (see c2k.dts for details about
the partitioning of the flash).
Signed-off-by: Remi Machet <rmachet@slac.stanford.edu>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The following adds support for the Analogue & Micro ASP 8347E, running
Redboot.
http://www.analogue-micro.com/ASP8347.html
Signed-off-by: Bryan O'Donoghue <bodonoghue@codehermit.ie>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds device tree nodes for NOR and NAND flashes and places
board-control node inside the localbus.
defconfig and board file updated appropriately.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
As of current mainline tree, TULIP driver is unusable on MPC8610HPCD
boards. There is a patch[1] floating around (and also included in the
BSP), which tries to heal the situation, though the ethernet is still
unusable. Practically it takes ages to mount NFS filesystem:
VFS: Mounted root (nfs filesystem).
Freeing unused kernel memory: 180k init
nfs: server 10.0.0.2 not responding, still trying
nfs: server 10.0.0.2 OK
nfs: server 10.0.0.2 not responding, still trying
nfs: server 10.0.0.2 not responding, still trying
nfs: server 10.0.0.2 not responding, still trying
nfs: server 10.0.0.2 not responding, still trying
nfs: server 10.0.0.2 OK
nfs: server 10.0.0.2 not responding, still trying
So, instead of trying to add uli526x functionality into TULIP driver
(which is already bloated enough), I fixed existing ULI526X driver
and now it works perfectly well here.
[1] http://www.bitshrine.org/gpp/0024-MPC8610-ETH-Lyra-native-ethernet.txt
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Board-specific defconfigs based on current mpc5200_defconfig, archival
lite5200_defconfig, and [cm5200|motionpro|tqm5200]_defconfig from the
linux-2.6-denx tree. Kernels build using these defconfigs were verified
to boot with root filesystem mounted over NFS on Motion-PRO, TQM5200
and Lite5200B boards. CM5200 target was not tested due to hardware
unavailability.
Signed-off-by: Bartlomiej Sieka <tur@semihalf.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Add board support for the Phytec pcm030 mpc5200b based board. It
does not need any platform specific fixups and as such is handled
as a mpc5200 simple platform.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This implements a new driver named windfarm_pm121, which drives the
fans on PowerMac 12,1 machines : iMac G5 iSight (rev C) 17" and
20". It's based on the windfarm_pm81 driver from Benjamin
Herrenschmidt.
This includes fixes from David Woodhouse correcting the names of some
of the sensors.
Signed-off-by: Étienne Bersac <bersace@gmail.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds a sample defconfig for the Wind River SBC8641D
board, with SMP, PCI and NFS root enabled.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add the device tree node for the DMA engine on 8544, publish
the device and enable the driver in the defconfig.
Signed-off-by: Sebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Board specific defconfigs are useful, however with the ability to do
multi-board defconfigs they aren't needed in the top level configs directory
Move the 83xx/85xx board specific defconfigs to individual directories under
arch/powerpc/configs.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Board specific defconfigs are useful, however with the ability to do
multi-board defconfigs they aren't needed in the top level configs directory.
Move the 4xx board specific defconfigs to individual directories under
arch/powerpc/configs.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This will remove some build warnings and doesn't stop us building any
drivers that we were building previously with these configs.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add default config for Emerson KSI8560 board.
Signed-off-by: Alexandr Smirnov <asmirnov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Some machines supported by the maple platform have an Obsidian
controller which can't be used without enabling CONFIG_IPR and the
options on which it depends.
Signed-off-by: Nathan Lynch <ntl@pobox.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Disable GEN_RTC since it conflicts with the i2c rtc drivers registering,
besides that keep most of the new defaults.
Signed-off-by: Olof Johansson <olof@lixom.net>