This patch applies customized PCI_DEVICE_ macros to specify the pci_ids
instead of open-coding them within the sdhci-pci driver.
By introducing device specific macros the pci_ids table becomes much
shorter and easier to comprehend than it would be possible using the
generic version of the PCI_DEVICE_ macros.
Signed-off-by: Matthias Kraemer <matthiasmartinsson@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The SDHCI_QUIRK_NO_MULTIBLOCK quirk was used as a workaround for the
ENGcm07207 erratum. However, it caused excruciatingly slow SD transfers
(300 kB/s on average), and this erratum actually does not imply that
multiple-block transfers are not supported, so this was overkill.
The suggested workaround for this erratum is to set SYSCTL.RSTA, but the
simple DAT line software reset (which resets the DMA circuit among
others) triggered by sdhci_finish_data() in case of errors seems to be
sufficient. Indeed, generating errors in a controlled manner on i.MX25
using the FEVT register right in the middle of read data transfers
without this quirk shows that nothing is written to the buffer by the
eSDHC past CMD12, and no extra Auto CMD12 is sent with AC12EN set, so
the data transfers on AHB are properly aborted. For write data
transfers, neither extra data nor extra Auto CMD12 is sent, as expected.
Moreover, after intensive stress tests on i.MX25, removing
SDHCI_QUIRK_NO_MULTIBLOCK seems to be safe.
SDHCI_QUIRK_BROKEN_ADMA has nothing to do with ENGcm07207, so set
ESDHC_FLAG_ERR004536 for the devices that had ESDHC_FLAG_ENGCM07207 set
in order to continue getting SDHCI_QUIRK_BROKEN_ADMA.
Signed-off-by: Benoît Thébaudeau <benoit@wsystem.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
On i.MX, SYSCTL.SDCLKFS may always be set to 0 in order to make the SD
clock frequency prescaler divide by 1 in SDR mode, even with the eSDHC.
The previous minimum prescaler value of 2 in SDR mode with the eSDHC was
a code remnant from PowerPC, which actually has this limitation on
earlier revisions.
In DDR mode, the prescaler can divide by up to 512.
The maximum SD clock frequency in High Speed mode is 50 MHz. On i.MX25,
this change makes it possible to get 48 MHz from the USB PLL
(240 MHz / 5 / 1) instead of only 40 MHz from the USB PLL
(240 MHz / 3 / 2) or 33.25 MHz from the AHB clock (133 MHz / 2 / 2).
Signed-off-by: Benoît Thébaudeau <benoit@wsystem.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
On i.MX25, the eSDHC DAT line software reset (SYSCTL.RSTD) unexpectedly
clears at least the data transfer width (PROCTL.DTW), which then results
in data CRC errors. This behavior is not documented, but it has actually
been observed. Consequently, the DAT line software resets triggered by
sdhci.c in case of errors caused unrecoverable errors.
Fix this by making sure that the DAT line software reset does not alter
the Host Control register. This behavior being undocumented, it may also
be present on other i.MX SoCs, so apply this fix for the whole i.MX
family.
Signed-off-by: Benoît Thébaudeau <benoit@wsystem.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The eSDHC can only DMA from 32-bit-aligned addresses.
This fixes the following test cases of mmc_test:
11: Badly aligned write
12: Badly aligned read
13: Badly aligned multi-block write
14: Badly aligned multi-block read
Signed-off-by: Benoît Thébaudeau <benoit@wsystem.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fix various English mistakes and typos in comments and in printed
strings.
Signed-off-by: Benoît Thébaudeau <benoit@wsystem.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Null check at line 1165: if (mrq->cmd), implies that mrq->cmd might
be NULL.
Add null checks before dereferencing pointer mrq->cmd in order to avoid
any potential NULL pointer dereference.
Addresses-Coverity-ID: 1408740
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It is 'R-Car', not 'RCar'. No code or binding changes, only descriptive text.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Using the device_property interfaces allows the dw_mmc driver to work
on platforms which run on either device tree or ACPI.
Signed-off-by: David Woods <dwoods@mellanox.com>
Reviewed-by: Chris Metcalf <cmetcalf@mellanox.com>
Cc: stable@vger.linux.org
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
clk_prepare_enable() may fail, so we should better check its return value
and propagate it in the case of error.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Plain code move with no changes. Needed for refactoring. Also, looks
nicer if request and finish_request are next to each other.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The obviously wrong comment was added in 2011 with commit df3ef2d3c9
("mmc: protect the tmio_mmc driver against a theoretical race") but
already obsoleted half a year later with commit b9269fdd4f ("mmc:
tmio: fix recursive spinlock, don't schedule with interrupts disabled").
Fixes: b9269fdd4f ("mmc: tmio: fix recursive spinlock, don't schedule with interrupts disabled")
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Split handling mrq into a seperate function. We need to call it from
another place soon.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This part confused me and I had to read it twice until I got it. Let's
follow the standard pattern to bail out if something is wrong and keep
in the body of the function when everything is as expected.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This option is activated by all multiplatform configs and what
not so we almost always have it turned on, and the memory it
saves is negligible, even more so moving forward. The actual
bounce buffer only gets allocated only when used, the only
thing the ifdefs are saving is a little bit of code.
It is highly improper to have this as a Kconfig option that
get turned on by Kconfig, make this a pure runtime-thing and
let the host decide whether we use bounce buffers. We add a
new property "disable_bounce" to the host struct.
Notice that mmc_queue_calc_bouncesz() already disables the
bounce buffers if host->max_segs != 1, so any arch that has a
maximum number of segments higher than 1 will have bounce
buffers disabled.
The option CONFIG_MMC_BLOCK_BOUNCE is default y so the
majority of platforms in the kernel already have it on, and
it then gets turned off at runtime since most of these have
a host->max_segs > 1. The few exceptions that have
host->max_segs == 1 and still turn off the bounce buffering
are those that disable it in their defconfig.
Those are the following:
arch/arm/configs/colibri_pxa300_defconfig
arch/arm/configs/zeus_defconfig
- Uses MMC_PXA, drivers/mmc/host/pxamci.c
- Sets host->max_segs = NR_SG, which is 1
- This needs its bounce buffer deactivated so we set
host->disable_bounce to true in the host driver
arch/arm/configs/davinci_all_defconfig
- Uses MMC_DAVINCI, drivers/mmc/host/davinci_mmc.c
- This driver sets host->max_segs to MAX_NR_SG, which is 16
- That means this driver anyways disabled bounce buffers
- No special action needed for this platform
arch/arm/configs/lpc32xx_defconfig
arch/arm/configs/nhk8815_defconfig
arch/arm/configs/u300_defconfig
- Uses MMC_ARMMMCI, drivers/mmc/host/mmci.[c|h]
- This driver by default sets host->max_segs to NR_SG,
which is 128, unless a DMA engine is used, and in that case
the number of segments are also > 1
- That means this driver already disables bounce buffers
- No special action needed for these platforms
arch/arm/configs/sama5_defconfig
- Uses MMC_SDHCI, MMC_SDHCI_PLTFM, MMC_SDHCI_OF_AT91, MMC_ATMELMCI
- Uses drivers/mmc/host/sdhci.c
- Normally sets host->max_segs to SDHCI_MAX_SEGS which is 128 and
thus disables bounce buffers
- Sets host->max_segs to 1 if SDHCI_USE_SDMA is set
- SDHCI_USE_SDMA is only set by SDHCI on PCI adapers
- That means that for this platform bounce buffers are already
disabled at runtime
- No special action needed for this platform
arch/blackfin/configs/CM-BF533_defconfig
arch/blackfin/configs/CM-BF537E_defconfig
- Uses MMC_SPI (a simple MMC card connected on SPI pins)
- Uses drivers/mmc/host/mmc_spi.c
- Sets host->max_segs to MMC_SPI_BLOCKSATONCE which is 128
- That means this platform already disables bounce buffers at
runtime
- No special action needed for these platforms
arch/mips/configs/cavium_octeon_defconfig
- Uses MMC_CAVIUM_OCTEON, drivers/mmc/host/cavium.c
- Sets host->max_segs to 16 or 1
- Setting host->disable_bounce to be sure for the 1 case
arch/mips/configs/qi_lb60_defconfig
- Uses MMC_JZ4740, drivers/mmc/host/jz4740_mmc.c
- This sets host->max_segs to 128 so bounce buffers are
already runtime disabled
- No action needed for this platform
It would be interesting to come up with a list of the platforms
that actually end up using bounce buffers. I have not been
able to infer such a list, but it occurs when
host->max_segs == 1 and the bounce buffering is not explicitly
disabled.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Make renesas_sdhi_sys_dmac.c a top-level module file that makes use of
library code supplied by renesas_sdhi_core.c
This is in order to facilitate adding other variants of SDHI;
in particular SDHI using different DMA controllers.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
[Arnd: Fixed module build error]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Rename the source file SDHI. A follow-up patch will make it a library
file used by a different top-level module file.
The name "renesas" is chosen as the SDHI driver is applicable to a wider
range of SoCs than SH-Mobile it seems to be a more appropriate name.
However, the SDHI driver source itself, is left as sh_mobile_sdhi to
avoid unnecessary churn.
the name "core" was chosen to reflect the desired role of this file,
to provide core functionality to the sdhi driver. A follow-up patch will
move the file into that role.
Internal symbols have also been renamed to reflect the filename change.
The .name member of struct platform_driver and parameter to
MODULE_ALIAS() have not been changed in order to avoid the complication
of potentially breaking SH SoCs which still use platform drivers.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Rename the source file for DMA for SDHI as a follow-up to attaching
DMA code to the SDHI driver rather than the tmio_core driver.
The name "renesas" is chosen as the SDHI driver is applicable to a wider
range of SoCs than SH-Mobile it seems to be a more appropriate name.
However, the SDHI driver source itself, is left as sh_mobile_sdhi to
avoid unnecessary churn.
The name sys_dmac was chosen to reflect the type of DMA used.
Internal symbols have also been renamed to reflect the filename change.
A follow-up patch will re-organise the SDHI driver removing
the need for renesas_sdhi_get_dma_ops().
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Rename tmio_mmc_pio.c to tmio_mmc_core.c to more accurately reflect its
function: to provide core code for the tmio-mmc and sh-mobole-sdhi drivers.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Refactor DMA support to allow it to be provided by a set of call-backs
that are provided by a host driver. The motivation is to allow multiple
DMA implementations to be provided and instantiated at run-time.
Instantiate the existing DMA implementation from the sh_mobile_sdhi driver
which appears to match the current use-case. This has the side effect
of moving the DMA code from the tmio_core to the sh_mobile_sdhi driver.
A follow-up patch will change the source file for the SDHI DMA
implementation accordingly. Another follow-up patch will re-organise the
SDHI driver removing the need for tmio_mmc_get_dma_ops().
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reshuffle the comment at the top of the source
dropping filenames and moving up human readable strings.
This seems to be somewhat more useful information to start the
source file with. It is also less fragile, f.e. to file renames.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This reverts commit a6db2c8603 ("mmc: dw_mmc: Don't allow Runtime PM for
SDIO cards")'
As dw_mmc now is capable of preventing runtime PM suspend while SDIO IRQs
are enabled, let's drop the less fine-grained method, which is preventing
runtime PM suspend for all SDIO cards - no matter of whether SDIO IRQs are
being enabled or not.
In this way we don't keep the host runtime PM resumed, unless it's really
needed, thus avoiding to waste power.
Especially when SDIO IRQs is supported via a separate out-of-band IRQ line,
which isn't defined by the SDIO standard, typically the SDIO func driver
doesn't enable SDIO IRQs via sdio_claim_irq(). So, for these cases we can
now allow the dwmmc device to be runtime PM suspended in-between requests.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
To be able to handle SDIO IRQs the dw_mmc device needs to be powered and
providing clock to the SDIO card. Therefore, we must not allow the device
to be runtime PM suspended while SDIO IRQs are enabled.
To fix this, let's increase the runtime PM usage count while the mmc core
enables SDIO IRQs. Later when the mmc core tells dw_mmc to disable SDIO
IRQs, we drop the usage count to again allow runtime PM suspend.
This now becomes the default behaviour for dw_mmc. In cases where SDIO IRQs
can be re-routed as GPIO wake-ups during runtime PM suspend, one could
potentially allow runtime PM suspend. However, that will have to be
addressed as a separate change on top of this one.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Convert to use the more lightweight method for processing SDIO IRQs, which
involves the following changes:
- Enable MMC_CAP2_SDIO_IRQ_NOTHREAD when SDIO IRQ is supported and use
sdio_signal_irq() instead of mmc_signal_sdio_irq().
- Mask the SDIO IRQ before signaling a new one to be processed.
- Implement the ->ack_sdio_irq() callback to unmask the SDIO IRQ.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Add the missing endianness conversions when printing the USB
device-descriptor idVendor and idProduct fields during probe.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
AVR32 is gone. Now it's time to clean up the driver by removing
leftovers that was used by AVR32 related code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
At the end of either of the read or write loops len is always zero
and hence the non-zero check on len and return of -EIO is redundant
and can be removed.
Detected by CoverityScan, CID#114293 ("Logically dead code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
ret is signed however is printed as unsigned fix the same.
If printed as a negative number the result is easier to read.
No functional change.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The guid intel_dsm_guid does not need to be in global scope, so make it
static.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
There have been reports about SDIO failing with certain WiFi chips in
descriptor chain mode. SD / eMMC are working fine.
So let's fall back to bounce buffer mode for command SD_IO_RW_EXTENDED.
This was reported to fix the error.
Fixes: 79ed05e329 "mmc: meson-gx: add support for descriptor chain mode"
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
acpi_evaluate_dsm() and friends take a pointer to a raw buffer of 16
bytes. Instead we convert them to use guid_t type. At the same time we
convert current users.
acpi_str_to_uuid() becomes useless after the conversion and it's safe to
get rid of it.
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Borislav Petkov <bp@suse.de>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Cc: Amir Goldstein <amir73il@gmail.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Joerg Roedel <jroedel@suse.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Yisen Zhuang <yisen.zhuang@huawei.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The stingray SDHCI hardware supports ACMD12 and automatically
issues after multi block transfer completed.
If ACMD12 in SDHCI is disabled, spurious tx done interrupts are seen
on multi block read command with below error message:
Got data interrupt 0x00000002 even though no data
operation was in progress.
This patch uses SDHCI_QUIRK_MULTIBLOCK_READ_ACMD12 to enable
ACM12 support in SDHCI hardware and suppress spurious interrupt.
Signed-off-by: Srinath Mannam <srinath.mannam@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Fixes: b580c52d58 ("mmc: sdhci-iproc: add IPROC SDHCI driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If the regulator probing is not yet finished this driver
might catch a -EPROBE_DEFER. Returning after this condition
did not remove the created platform device. On a repeated
call to the probe function the of_platform_device_create
fails.
Calling of_platform_device_destroy after EPROBE_DEFER resolves
this bug.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In case the DT specifies neither a regulator nor a gpio
for the shared power the driver will crash accessing the regulator.
Prevent the crash by checking the regulator before use.
Use mmc_regulator_get_supply() instead of open coding the same
logic.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Now that the JZ4740 and similar SoCs have a pinctrl driver, we rely on
the pins being properly configured before the driver probes.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The devm_gpiod_get_optional() function appends a "-gpios" to the
string passed to it, so if we want to find the "power-gpios" signal,
we must pass "power" to this function.
Fixes: 01d9584333 ("mmc: cavium: Add MMC support for Octeon SOCs.")
Signed-off-by: David Daney <david.daney@cavium.com>
[jglauber@cavium.com: removed point after subject line]
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
OCTEON SoCs with CIU3 do not have interrupt masking local to the MMC
bus interface. Unfortunately, some even have a diagnostic register at
the same address of the enable register, which causes the interrupts
to fire immediately if stored to, thus breaking the driver. The proper
action on these SoCs is not to touch this register.
Fixes: 01d9584333 ("mmc: cavium: Add MMC support for Octeon SOCs.")
Signed-off-by: David Daney <david.daney@cavium.com>
[jglauber@cavium.com: removed point after subject line]
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently, the xenon_clean_phy() is only used for freeing phy_params.
The phy_params is allocated by devm_kzalloc(), there's no need to free
is explicitly.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Hu Ziji <huziji@marvell.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
-----BEGIN PGP SIGNATURE-----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=lbS7
-----END PGP SIGNATURE-----
Merge tag 'hwparam-20170420' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
Pull hw lockdown support from David Howells:
"Annotation of module parameters that configure hardware resources
including ioports, iomem addresses, irq lines and dma channels.
This allows a future patch to prohibit the use of such module
parameters to prevent that hardware from being abused to gain access
to the running kernel image as part of locking the kernel down under
UEFI secure boot conditions.
Annotations are made by changing:
module_param(n, t, p)
module_param_named(n, v, t, p)
module_param_array(n, t, m, p)
to:
module_param_hw(n, t, hwtype, p)
module_param_hw_named(n, v, t, hwtype, p)
module_param_hw_array(n, t, hwtype, m, p)
where the module parameter refers to a hardware setting
hwtype specifies the type of the resource being configured. This can
be one of:
ioport Module parameter configures an I/O port
iomem Module parameter configures an I/O mem address
ioport_or_iomem Module parameter could be either (runtime set)
irq Module parameter configures an I/O port
dma Module parameter configures a DMA channel
dma_addr Module parameter configures a DMA buffer address
other Module parameter configures some other value
Note that the hwtype is compile checked, but not currently stored (the
lockdown code probably won't require it). It is, however, there for
future use.
A bonus is that the hwtype can also be used for grepping.
The intention is for the kernel to ignore or reject attempts to set
annotated module parameters if lockdown is enabled. This applies to
options passed on the boot command line, passed to insmod/modprobe or
direct twiddling in /sys/module/ parameter files.
The module initialisation then needs to handle the parameter not being
set, by (1) giving an error, (2) probing for a value or (3) using a
reasonable default.
What I can't do is just reject a module out of hand because it may
take a hardware setting in the module parameters. Some important
modules, some ipmi stuff for instance, both probe for hardware and
allow hardware to be manually specified; if the driver is aborts with
any error, you don't get any ipmi hardware.
Further, trying to do this entirely in the module initialisation code
doesn't protect against sysfs twiddling.
[!] Note that in and of itself, this series of patches should have no
effect on the the size of the kernel or code execution - that is
left to a patch in the next series to effect. It does mark
annotated kernel parameters with a KERNEL_PARAM_FL_HWPARAM flag in
an already existing field"
* tag 'hwparam-20170420' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs: (38 commits)
Annotate hardware config module parameters in sound/pci/
Annotate hardware config module parameters in sound/oss/
Annotate hardware config module parameters in sound/isa/
Annotate hardware config module parameters in sound/drivers/
Annotate hardware config module parameters in fs/pstore/
Annotate hardware config module parameters in drivers/watchdog/
Annotate hardware config module parameters in drivers/video/
Annotate hardware config module parameters in drivers/tty/
Annotate hardware config module parameters in drivers/staging/vme/
Annotate hardware config module parameters in drivers/staging/speakup/
Annotate hardware config module parameters in drivers/staging/media/
Annotate hardware config module parameters in drivers/scsi/
Annotate hardware config module parameters in drivers/pcmcia/
Annotate hardware config module parameters in drivers/pci/hotplug/
Annotate hardware config module parameters in drivers/parport/
Annotate hardware config module parameters in drivers/net/wireless/
Annotate hardware config module parameters in drivers/net/wan/
Annotate hardware config module parameters in drivers/net/irda/
Annotate hardware config module parameters in drivers/net/hamradio/
Annotate hardware config module parameters in drivers/net/ethernet/
...
The ls1046a datasheet specified that the max SD clock frequency
for eSDHC SDR104/HS200 was 167MHz, and the ls1012a datasheet
specified it's 125MHz for ls1012a. So this patch is to add the
limitation.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The loop to poll ESDHC_CLOCK_STABLE bit with mdelay would waste time
because the time to stabilize is much less than 1 ms. This patch is
to use udelay instead to avoid time wasting.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The default value of LOGIC_TIMING_ADJUST register in eMMC 5.0 PHY is
different from that in eMMC 5.1 PHY. Set the specific value for that
register in eMMC 5.0 PHY.
Signed-off-by: Hu Ziji <huziji@marvell.com>
Reported-by: Jisheng Zhang <jszhang@marvell.com>
Tested-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
sdhci_remove_host() might execute SOFT_RESET_ALL. Inside xenon_remove(),
Xenon SDHC should be enabled during sdhci_remove_host().
Move xenon_sdhc_unprepare after sdhci_remove_host() such that Xenon SDHC is
disabled after sdhci_remove_host() completes.
Signed-off-by: Hu Ziji <huziji@marvell.com>
Reported-by: Jisheng Zhang <jszhang@marvell.com>
Tested-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use the module_pci_driver() macro to make the code simpler
by eliminating module_init and module_exit calls.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add platform driver for Octeon SOCs.
Signed-off-by: Steven J. Hill <Steven.Hill@cavium.com>
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use the mmc_card_is_blockaddr() function to properly detect if the
card uses byte or block addressing.
Signed-off-by: Steven J. Hill <Steven.Hill@cavium.com>
Acked-by: David Daney <david.daney@cavium.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
USDHC tuning circuit should be reset before every time card enumeration
or re-enumeration.
SD3.0 card need tuning. For SDR104 card, when system suspend in standby
mode, and then resume back, the IO timing is still SDR104(tuned) which
may result in card re-enumeration fail in low card speed(400khz) for some
cards. And we did meet the issue that in certain probability, SDR104
card meet mmc command CRC/Timeout error when send CMD2 during mmc bus
resume.
This patch reset the tuning circuit when the ios timing is
MMC_TIMING_LEGACY/MMC_TIMING_MMC_HS/MMC_TIMING_SD_HS, which means both
mmc_power_up() and mmc_power_off() will reset the tuning circuit.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It's observed that eSDHC needed delay between tuning cycles for
HS200 successful tuning. This patch is to set 1ms delay for that.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The delay between tuning commands for SD cards is not part of the
specification. A driver that needs it probably needs it for eMMC
too, whereas most drivers would probably like to set it to 0. Make
it a host member (host->tuning_delay) that defaults to the existing
behaviour. Drivers can set it to zero to eliminate the delay, or
set it to a positive value to always have a delay.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
eSDHC uses tuning block for tuning procedure. So the tuning
block control register must be configured properly before tuning.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
eSDHC supports signal voltage switch from 3.3v to 1.8v by
eSDHC_PROCTL[VOLT_SEL] bit. This bit changes the value of output
signal SDHC_VS, and there must be a control circuit out of eSDHC
to change the signal voltage according to SDHC_VS output signal.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
eSDHC could select peripheral clock or platform clock as clock source by
the PCS bit of eSDHC Control Register, and this bit couldn't be reset by
software reset for all. In default, the platform clock is used. But we have
to use peripheral clock since it has a higher frequency to support eMMC
HS200 mode and SD UHS-I mode. This patch is to add peripheral clock support
and use it instead of platform clock if it's declared in eSDHC dts node.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The DSM used by some Intel controllers can return a 3 byte package. Allow
for that by using memcpy to copy the bytes.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
"dat" is a u64 and "shift" starts as 54 so this is a shift wrapping bug.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add a pointer check to prevent this smatch warning:
drivers/mmc/host/cavium.c:803 cvm_mmc_request()
error: we previously assumed 'cmd->data' could be null (see line 782)
This is a theoretical fix because MMC_CMD_ADTC seems to imply
that cmd->data is not null. Nevertheless checking cmd->data
before using it improves readability.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
So far a bounce buffer is used to serialize the scatterlist(s).
This overhead can be avoided by switching to descriptor chain mode.
As result the performance is drastically improved. On a Odroid-C2 with
a 128 GB eMMC module raw reads reach 140 MB/s.
Prerequisite for descriptor chain mode is that all scatterlist buffers
are 8 byte aligned for 64-bit DMA. That's not always the case, at least
the brcmfmac SDIO WiFi driver is known to cause problems.
Therefore, for each request, check upfront whether all scatterlist
buffers are 8 byte aligned and fall back to bounce buffer mode if
that's not the case.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds basic tuning which changes the rx clock phase only
until a working setting is found.
On a Odroid C2 with 128GB eMMC card and 200 MHz MMC clock only
180° rx clock phase make the system boot w/o CRC errors.
With other MMC devices / clock speeds this might be different,
therefore don't change the driver config in general.
When retuning skip the currently active parameter set. This avoids
the current problematic config to be chosen again if it causes CRC
errors just occasionally.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Introduce struct meson_tuning_params for storing the clock phase
configurations. There's no functional change because tx and rx
clock phase were implicitely set to CLK_PHASE_0 before.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
devm_pinctrl_get() returns error pointers, it never returns NULL.
Fixes: 455e5cd6f7 ("mmc: omap_hsmmc: Pin remux workaround to support SDIO interrupt on AM335x")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some SoCs have PHY PAD outside Xenon IP.
PHY PAD voltage should match signalling voltage in use.
Add generic SoC PHY PAD voltage control interface.
Implement Aramda-3700 SoC PHY PAD voltage control.
Signed-off-by: Hu Ziji <huziji@marvell.com>
Tested-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Marvell Xenon eMMC/SD/SDIO Host Controller contains PHY.
Multiple types of PHYs are supported.
Add support to multiple types of PHYs init and configuration.
Add register definitions of PHYs.
Xenon PHY cannot fit in kernel common PHY framework.
Xenon SDHC PHY register is a part of Xenon SDHC register set.
Besides, MMC initialization has to call several PHY functions to
complete timing setting.
Those PHY setting functions have to access SDHC registers and know
current MMC setting, such as bus width, clock frequency and
speed mode.
As a result, implement Xenon PHY in MMC host directory.
Signed-off-by: Hu Ziji <huziji@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add Xenon eMMC/SD/SDIO host controller core functionality.
Add Xenon specific initialization process.
Add Xenon specific mmc_host_ops APIs.
Add Xenon specific register definitions.
Add CONFIG_MMC_SDHCI_XENON support in drivers/mmc/host/Kconfig.
Marvell Xenon SDHC conforms to SD Physical Layer Specification
Version 3.01 and is designed according to the guidelines provided
in the SD Host Controller Standard Specification Version 3.00.
Signed-off-by: Hu Ziji <huziji@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Export sdhci_start_signal_voltage_switch() from sdhci.c.
Thus vendor sdhci driver can implement its own signal voltage
switch routine.
Signed-off-by: Hu Ziji <huziji@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Export sdhci_set_ios() in sdhci.c.
Thus vendor sdhci driver can implement its own set_ios() routine.
Signed-off-by: Hu Ziji <huziji@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add support for switching to DDR mode for eMMC devices.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add Support for the scatter-gather DMA available in the
ThunderX MMC units. Up to 16 DMA requests can be processed
together.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This core driver will be used by a MIPS platform driver
or by an ARM64 PCI driver. The core driver implements the
mmc_host_ops and slot probe & remove functions.
Callbacks are provided to allow platform specific interrupt
enable and bus locking.
The host controller supports:
- up to 4 slots that can contain sd-cards or eMMC chips
- 1, 4 and 8 bit bus width
- SDR and DDR
- transfers up to 52 Mhz (might be less when multiple slots are used)
- DMA read/write
- multi-block read/write (but not stream mode)
Voltage is limited to 3.3v and shared for all slots (vmmc and vmmcq).
A global lock for all MMC devices is required because the host
controller is shared.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Steven J. Hill <steven.hill@cavium.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Factor out setting the response configuration bits thus further reducing
complexity of function meson_mmc_start_cmd.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Factor out setting the block size. This also contributes to reducing
complexity of function meson_mmc_start_cmd.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use added dev variable for devm_clk_get.
Signed-off-by: Piotr Sroka <piotrs@cadence.com>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
DTS properties are used instead of fixed data
because PHY settings can be different for different chips/boards.
Signed-off-by: Piotr Sroka <piotrs@cadence.com>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add polling for ACK to be sure that data are written to PHY register.
Signed-off-by: Piotr Sroka <piotrs@cadence.com>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This fixes a NULL pointer dereference in case of a MMC request with a
set block count command and no data.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
CMD23 mode (use "set block count" command before transferring multiple
data blocks) typically is more performant as host / card know upfront
how many data blocks to expect. Therefore add support for this mode to
the driver.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently we use a fixed timeout of 4s for all data transfers. Switch
to dynamic timeout values by making use of data->timeout_ns.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
So far the driver name is used as interrupt description, therefore in
/proc/interrupts it's not possible to tell which interrupt belongs to
which port. Change this by switching to NULL what causes the default
(device name) to be used. In our case that's the DT node name.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use GENMASK consistently for all bit masks and switch to using the
bitfield macros FIELD_GET and FIELD_PREP. This hides parts of the
complexity of dealing with bit fields.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently the get_timeout_clock callback doesn't clearly
have a statement that it needs the variant drivers to return
the timeout clock rate in kHz if the SDHCI_TIMEOUT_CLK_UNIT
isn't present, otherwise the variant drivers should return it
in MHz. It's also very likely that further variant drivers which
are going to use this callback will be confused by this situation.
Given the fact that moderm sdhci variant hosts are very prone to get
the timeout clock from common clock framework (actually the only three
users did that), it's more natural to return the value in Hz and we
make an explicit comment there. Then we put the unit conversion inside
the sdhci core. Thus will improve the code and prevent further misuses.
Reported-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The controller's errors are usually normal (for example, for MMC or SDIO
cards, some errors are expected to happen; and for boards without a
dedicated card detect pin the error info will even flood console and
hide other normal messages) and hard to understand.
Change their print level to debug, thus it won't be shown to generic
users.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We don't need variable cmd_cfg_timeout, so remove it and simplify the
code a little.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Centralize setting data->bytes_xfered in one place and make sure
that the number of transfererd bytes is set only if we receive
the end-of-chain interrupt and there was no error.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Response reading can be slightly improved by doing it in just one place.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Simplify the code by using two variables instead of a struct sd_emmc_desc.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Replace cmd->data with a local variable to simplify code a little.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
The variables holding the configuration bits are zero-initialized.
So we can remove all bit resets.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
If we don't select a set of better parameters for our emmc host,
It may easily occur CMD response CRC error. And also it may cause
cannot boot up issue.
Fot getting a set of better parameters, our emmc host supports
data tune mechanism.Therefore, our emmc driver also should change
to use data tune for CMD line.
Because our emmc host use the different clock source to sample the
CMD signal between HS200 and HS400 mode, the parameters are also
different between these two modes.
Separate cmd internal delay for HS200/HS400 mode.
This change can fix "System can not boot up" issue.
Signed-off-by: Yong Mao <yong.mao@mediatek.com>
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Current code gets number of taps only once and keeps the value. This is
not correct, we need to obtain it every time before executing tuning,
so remove the outer if-block.
Signed-off-by: Masaharu Hayakawa <masaharu.hayakawa.ry@renesas.com>
[wsa: extracted from a larger patch and reworded commit message]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In the (maybe academical) case, we don't get a DATAEND interrupt after
DMA completed, we will wait endlessly for the completion to complete.
This is not bad per se, since we have a more generic completion tracking
a timeout. In that rare case, however, the DMA buffer will not get
unmapped and we have a leak. Reorder the code, so unmapping will always
take place.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Move a function to avoid having to forward declare it in a subsequent
patch.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
The suspend / resume callbacks lack the flexibility to allow a device to
specify a different function entirely. Change them around so that device
functions are called directly and they in turn can call the default
implementations if needed.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
It is confusing to have some parts of suspend / resume under conditional
compilation and some parts not. Use conditional compilation everywhere.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Do not use suspend/resume callbacks with runtime pm. It doesn't make sense
and isn't being used, so remove.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
SDHCI provides more flexibility than simply calling sdhci_add_host(). Make
that available by allowing devices to specify their own ->add_host()
function.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Add an interrupt hook and helper functions for enabling, disabling and
delivering interrupts to a CQE.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Get rid of unnecessary 'extern' in header file.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Export sdhci_dumpregs so that it can be called by drivers.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Ensure all prints start with the mmc host name, and the text all lines up.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Ensure all debug prints start with the mmc host name.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Tuning execution is already synchronized with respect to other host
operations by upper layers "claiming" the host, which also takes care of
runtime pm. There can be no requests in progress. Retain the spin lock
usage only for ensuring that sending tuning commands is synchronized with
respect to the interrupt handler.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
The spin lock is not necessary in set_ios. Anything that is racing with
changes to the I/O state is already broken. The mmc core already provides
synchronization via "claiming" the host. So remove spin_lock and friends
from sdhci_set_ios and related callbacks.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Drivers can use the host operation directly, so remove this now unused
callback.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Make use of an Intel ACPI _DSM that provides eMMC driver strength.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Make use of an Intel ACPI _DSM that indicates if re-tuning is needed after
D3.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Let devices define their own private data to facilitate device-specific
operations. The size of the private structure is specified in the
sdhci_pci_fixes structure, then sdhci_pci_probe_slot() will allocate extra
space for it, and sdhci_pci_priv() can be used to get a reference to it.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Devices might save and restore tuning values so that re-tuning might not be
needed after a pm transition. Let drivers decide by pushing the
mmc_retune_needed() logic down to them.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
The delay loops for reset and clock enable always take at least 1 ms
because they use mdelay(1). However they can take a lot less time e.g. less
than 50us. Use ktime and reduce the delay to 10 microseconds per loop.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
The 2835 has two SD controllers: The Arasan sdhci controller (supported
by the iproc driver) and a custom sdhost controller. This patch adds a
driver for the latter.
The sdhci controller supports both sdcard and sdio. The sdhost
controller supports the sdcard only, but has better performance. Also
note that the rpi3 has sdio wifi, so driving the sdcard with the sdhost
controller allows to use the sdhci controller for wifi support.
The configuration is done by devicetree via pin muxing. Both SD
controller are available on the same pins (2 pin groups = pin 22 to 27 +
pin 48 to 53). So it's possible to use both SD controllers at the same
time with different pin groups.
The code was originally written by Phil Elwell in the downstream
Rasbperry Pi tree. In preparation for the upstream merge it was
cleaned up and the code base was moderized by Eric Anholt, Stefan
Wahren and Gerd Hoffmann.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch fixes the case where meson_mmc_probe function fails before
core_clk is enabled.
Originally, that would result in a try to disable the core clock, and if
it was not already enabled, it would result in a kernel warning.
This issue is similar to the one with div_clk.
Fix it by introducing another error path used only between successfully
enabling the core clock, and successfully enabling the div clock.
That would ensure that core clock is disabled only if it was enabled before.
Signed-off-by: Michał Zegan <webczat@webczatnet.pl>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
sdhci_pltfm_init() has already set the platform drvdata for us, remove
the unnecessary platform_set_drvdata() call.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
sdhci_pltfm_init() has already set the platform drvdata for us, remove
the unnecessary platform_set_drvdata() call.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The SDHCI controller found on NVIDIA Tegra186 SoCs is very similar to
the one on prior generations of Tegra and can be supported by the same
driver.
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The device tree binding for the SDHCI controller found on Tegra SoCs
specifies that a reset control can be provided by the device tree. No
code was ever added to support the module reset, which can cause the
driver to try and access registers from a module that's in reset. On
most Tegra SoC generations doing so would cause a hang.
Note that it's unlikely to see this happen because on most platforms
these resets will have been deasserted by the bootloader. However the
portability can be improved by making sure the driver deasserts the
reset before accessing any registers.
Since resets are synchronous on Tegra SoCs, the platform driver needs
to implement a custom ->remove() callback now to make sure the clock
is disabled after the reset is asserted.
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The mmc host was added in meson_mmc_probe, but never removed in
meson_mmc_remove.
Fix that by removing the host before deallocating other resources.
Signed-off-by: Michał Zegan <webczat@webczatnet.pl>
Tested-by: Michał Zegan <webczat@webczatnet.pl>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
After we received the dataend interrupt, R1 response register carries
the value from the automatically generated stop command. Report that
info back to the MMC block layer, so we will be notified in case of e.g.
ECC errors which happened during the last transfer.
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Halting the kernel on an unsupported stop command seems overkill, report
the error and say what we already did (due to autocmd12) instead.
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Making sure we match the actual register names.
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The current code assumes that DMA is finished before SD access end is
flagged. Thus, it schedules the 'dma_complete' tasklet in the SD card
interrupt routine when DATAEND is set. The assumption is not safe,
though. Even by mounting an SD card, it can be seen that sometimes DMA
complete is first, sometimes DATAEND. It seems they are usually close
enough timewise to not cause problems. However, a customer reported that
with CMD53 sometimes things really break apart. As a result, the BSP has
a patch which introduces flags for both events and makes sure both flags
are set before scheduling the tasklet. The customer accepted the patch,
yet it doesn't seem a proper upstream solution to me.
This patch refactors the code to replace the tasklet with already
existing and more lightweight mechanisms. First of all, we set the
callback in a DMA descriptor to automatically get notified when DMA is
done. In the callback, we then use a completion to make sure the SD
access has already ended. Then, we proceed as before.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is no check if clk_prepare_enable() succeed in sdhci_pxav2_probe().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Struct mmc_command includes a reference to the related mmc_request.
Therefore we don't have to store mrq separately in struct meson_host.
And we can remove some now unneeded WARN_ON's.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Config values which are not changed during runtime we can set
in the probe function already.
The block size setting is overwritten later in
meson_mmc_start_cmd anyway if needed, so it doesn't harm if we
remove this setting in meson_mmc_set_ios.
In addition write config register only if configuration changed.
Don't change the location of clock initialization as in an
earlier version of the patch, this change causes a hang.
This issue was reported and fix suggested by:
Helmut Klein <hgkr.klein@gmail.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
CLK core does a deep copy of init.name, therefore it's fully ok to
provide a local variable.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The condition should be "if (ret)" as the disable/unprepare is
supposed to be executed if the previous command fails.
In addition adjust the error path in probe to properly deal
with the case that cfg_div_clk can be registered successfully
but enable/prepare fails.
In this case we shouldn't call clk_disable_unprepare.
Reported-by: Michał Zegan <webczat_200@poczta.onet.pl>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Member mux_parent isn't used outside meson_mmc_clk_init. So remove it
and replace it with a local variable in meson_mmc_clk_init.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Because the DT requires a fixed number of mux parent clocks,
variable mux_parent_count can be replaced with constant
MUX_CLK_NUM_PARENTS, so remove it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Member ocr_mask is never used and member irq we can replace with a
local variable in meson_mmc_probe. So let's remove both members.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The return value of meson_mmc_request_done and meson_mmc_read_resp
isn't used, so make both functions return void.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Core ensures that there are no commands with cmd->data being set and
nothing to transfer. And we don't have to reset bit CMD_CFG_DATA_NUM
because cmd_cfg was zero-initialized and this bit isn't set.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Too much condition iteration makes the code
less readable. Slightly improve it.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
No need to declar it there, remove it.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Just use the readl_poll_timeout{_atomic} to avold open
coding them.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently for DDR50 card, it need tuning in default. We meet tuning fail
issue for DDR50 card and some data CRC error when DDR50 sd card works.
This is because the default pad I/O drive strength can't make sure DDR50
card work stable. So increase the pad I/O drive strength for DDR50 card,
and use pins_100mhz.
This fixes DDR50 card support for IMX since DDR50 tuning was enabled from
commit 9faac7b95e ("mmc: sdhci: enable tuning for DDR50")
Tested-and-reported-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Cc: stable@vger.kernel.org # v4.4+
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When the kernel is running in secure boot mode, we lock down the kernel to
prevent userspace from modifying the running kernel image. Whilst this
includes prohibiting access to things like /dev/mem, it must also prevent
access by means of configuring driver modules in such a way as to cause a
device to access or modify the kernel image.
To this end, annotate module_param* statements that refer to hardware
configuration and indicate for future reference what type of parameter they
specify. The parameter parser in the core sees this information and can
skip such parameters with an error message if the kernel is locked down.
The module initialisation then runs as normal, but just sees whatever the
default values for those parameters is.
Note that we do still need to do the module initialisation because some
drivers have viable defaults set in case parameters aren't specified and
some drivers support automatic configuration (e.g. PNP or PCI) in addition
to manually coded parameters.
This patch annotates drivers in drivers/mmc/host/.
Suggested-by: Alan Cox <gnomes@lxorguk.ukuu.org.uk>
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Pierre Ossman <pierre@ossman.eu>
cc: Ulf Hansson <ulf.hansson@linaro.org>
cc: linux-mmc@vger.kernel.org
According to the SDIO standard interrupts are normally signalled in a
very complicated way. They require the card clock to be running and
require the controller to be paying close attention to the signals
coming from the card. This simply can't happen with the clock stopped
or with the controller in a low power mode.
To that end, we'll disable runtime_pm when we detect that an SDIO card
was inserted. This is much like with what we do with the special
"SDMMC_CLKEN_LOW_PWR" bit that dw_mmc supports.
NOTE: we specifically do this Runtime PM disabling at card init time
rather than in the enable_sdio_irq() callback. This is _different_
than how SDHCI does it. Why do we do it differently?
- Unlike SDHCI, dw_mmc uses the standard sdio_irq code in Linux (AKA
dw_mmc doesn't set MMC_CAP2_SDIO_IRQ_NOTHREAD).
- Because we use the standard sdio_irq code:
- We see a constant stream of enable_sdio_irq(0) and
enable_sdio_irq(1) calls. This is because the standard code
disables interrupts while processing and re-enables them after.
- While interrupts are disabled, there's technically a period where
we could get runtime disabled while processing interrupts.
- If we are runtime disabled while processing interrupts, we'll
reset the controller at resume time (see dw_mci_runtime_resume),
which seems like a terrible idea because we could possibly have
another interrupt pending.
To fix the above isues we'd want to put something in the standard
sdio_irq code that makes sure to call pm_runtime get/put when
interrupts are being actively being processed. That's possible to do,
but it seems like a more complicated mechanism when we really just
want the runtime pm disabled always for SDIO cards given that all the
other bits needed to get Runtime PM vs. SDIO just aren't there.
NOTE: at some point in time someone might come up with a fancy way to
do SDIO interrupts and still allow (some) amount of runtime PM.
Technically we could turn off the card clock if we used an alternate
way of signaling SDIO interrupts (and out of band interrupt is one way
to do this). We probably wouldn't actually want to fully runtime
suspend in this case though--at least not with the current
dw_mci_runtime_resume() which basically fully resets the controller at
resume time.
Fixes: e9ed8835e9 ("mmc: dw_mmc: add runtime PM callback")
Cc: <stable@vger.kernel.org>
Reported-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The controller has different timings for MMC_TIMING_UHS_DDR50 and
MMC_TIMING_MMC_DDR52. Configuring the controller with SDHCI_CTRL_UHS_DDR50,
when MMC_TIMING_MMC_DDR52 timings are requested, is not correct and can
lead to unexpected behavior.
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Fixes: bb5f8ea4d5 ("mmc: sdhci-of-at91: introduce driver for the Atmel SDMMC")
Cc: <stable@vger.kernel.org> # 4.4+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SDIO cards may need clock to send the card interrupt to the host.
On a cherrytrail tablet with a RTL8723BS wifi chip, without this patch
pinging the tablet results in:
PING 192.168.1.14 (192.168.1.14) 56(84) bytes of data.
64 bytes from 192.168.1.14: icmp_seq=1 ttl=64 time=78.6 ms
64 bytes from 192.168.1.14: icmp_seq=2 ttl=64 time=1760 ms
64 bytes from 192.168.1.14: icmp_seq=3 ttl=64 time=753 ms
64 bytes from 192.168.1.14: icmp_seq=4 ttl=64 time=3.88 ms
64 bytes from 192.168.1.14: icmp_seq=5 ttl=64 time=795 ms
64 bytes from 192.168.1.14: icmp_seq=6 ttl=64 time=1841 ms
64 bytes from 192.168.1.14: icmp_seq=7 ttl=64 time=810 ms
64 bytes from 192.168.1.14: icmp_seq=8 ttl=64 time=1860 ms
64 bytes from 192.168.1.14: icmp_seq=9 ttl=64 time=812 ms
64 bytes from 192.168.1.14: icmp_seq=10 ttl=64 time=48.6 ms
Where as with this patch I get:
PING 192.168.1.14 (192.168.1.14) 56(84) bytes of data.
64 bytes from 192.168.1.14: icmp_seq=1 ttl=64 time=3.96 ms
64 bytes from 192.168.1.14: icmp_seq=2 ttl=64 time=1.97 ms
64 bytes from 192.168.1.14: icmp_seq=3 ttl=64 time=17.2 ms
64 bytes from 192.168.1.14: icmp_seq=4 ttl=64 time=2.46 ms
64 bytes from 192.168.1.14: icmp_seq=5 ttl=64 time=2.83 ms
64 bytes from 192.168.1.14: icmp_seq=6 ttl=64 time=1.40 ms
64 bytes from 192.168.1.14: icmp_seq=7 ttl=64 time=2.10 ms
64 bytes from 192.168.1.14: icmp_seq=8 ttl=64 time=1.40 ms
64 bytes from 192.168.1.14: icmp_seq=9 ttl=64 time=2.04 ms
64 bytes from 192.168.1.14: icmp_seq=10 ttl=64 time=1.40 ms
Cc: Dong Aisheng <b29396@freescale.com>
Cc: Ian W MORRISON <ianwmorrison@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Disabling interrupts for even a millisecond can cause problems for some
devices. That can happen when Intel host controllers wait for the present
state to propagate.
The spin lock is not necessary here. Anything that is racing with changes
to the I/O state is already broken. The mmc core already provides
synchronization via "claiming" the host.
Although the spin lock probably should be removed from the code paths that
lead to this point, such a patch would touch too much code to be suitable
for stable trees. Consequently, for this patch, just drop the spin lock
while waiting.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v4.9+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Disabling interrupts for even a millisecond can cause problems for some
devices. That can happen when sdhci changes clock frequency because it
waits for the clock to become stable under a spin lock.
The spin lock is not necessary here. Anything that is racing with changes
to the I/O state is already broken. The mmc core already provides
synchronization via "claiming" the host.
Although the spin lock probably should be removed from the code paths that
lead to this point, such a patch would touch too much code to be suitable
for stable trees. Consequently, for this patch, just drop the spin lock
while waiting.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer should a malicious device lack endpoints.
Fixes: 53f3a9e26e ("mmc: USB SD Host Controller (USHC) driver")
Cc: stable <stable@vger.kernel.org> # 2.6.37
Cc: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The SDHCI controller in the SAMA5D2 chip requires a valid voltage set
in the power control register, otherwise commands will fail with a
timeout error.
When using the regulator framework to specify the regulator used by the
mmc device, the voltage is not configured, and it is not possible to use
the connected device.
Implement a custom 'set_power' function for this specific hardware, that
configures the voltage in the register in all cases.
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: stable@vger.kernel.org #4.9+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch can fix two issues:
Issue 1:
In previous code, div may be overflow when setting clock frequency
as f_min. We can use DIV_ROUND_UP to fix this boundary related
issue.
Issue 2:
In previous code, we can not set the correct clock frequency when
div equals 0xff.
Signed-off-by: Yong Mao <yong.mao@mediatek.com>
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
sdhci_arasan_get_timeout_clock() divides the frequency it has with (1 <<
(13 + divisor)).
However, the divisor is not some Arasan-specific value, but instead is
just the Data Timeout Counter Value from the SDHCI Timeout Control
Register.
Applying it here like this is wrong as the sdhci driver already takes
that value into account when calculating timeouts, and in fact it *sets*
that register value based on how long a timeout is wanted.
Additionally, sdhci core interprets the .get_timeout_clock callback
return value as if it were read from hardware registers, i.e. the unit
should be kHz or MHz depending on SDHCI_TIMEOUT_CLK_UNIT capability bit.
This bit is set at least on the tested Zynq-7000 SoC.
With the tested hardware (SDHCI_TIMEOUT_CLK_UNIT set) this results in
too high a timeout clock rate being reported, causing the core to use
longer-than-needed timeouts. Additionally, on a partitioned MMC
(therefore having erase_group_def bit set) mmc_calc_max_discard()
disables discard support as it looks like controller does not support
the long timeouts needed for that.
Do not apply the extra divisor and return the timeout clock in the
expected unit.
Tested with a Zynq-7000 SoC and a partitioned Toshiba THGBMAG5A1JBAWR
eMMC card.
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Fixes: e3ec3a3d11 ("mmc: arasan: Add driver for Arasan SDHCI")
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fix typos and add the following to the scripts/spelling.txt:
intialization||initialization
The "inintialization" in drivers/acpi/spcr.c is a different pattern but
I fixed it as well in this commit.
Link: http://lkml.kernel.org/r/1481573103-11329-16-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This macro is currently unused, but it may be useful for debug use.
Fix it just in case.
Fixes: ff6af28faf ("mmc: sdhci-cadence: add Cadence SD4HC support")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add support for HS400 mode.
The driver still misses support for tuning, therefore
highspeed modes like HS400 might not work under all
circumstances yet.
Successfully tested on a Odroid C2 (S905 GXBB).
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The remove callback is called only if probe finished successfully.
Therefore these checks are not needed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
A bounce buffer of 512K isn't needed as the max request size is
511 * 512 byte.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
So far max_blk_count isn't set what results in a default of value 8
to be used (PAGE_SIZE / block size).
Block length field has 9 bits, so set max_blk_count to 2^9-1 = 511.
In addition set max_req_size because max_blk_count is also limited
by max_req_size / block_size.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Disabling and immediately re-enabling interrupts in meson_mmc_request
doesn't provide a benefit. Instead enable interrupts in probe already.
And disable interrupts in remove, this was missing so far.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Remove unneeded variable ret and simplify the if block.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The following changes are quite small, therefore I combined them in
one patch.
- ret doesn't need to be initialized with 0
- use standard !clk_rate notation to check for a zero value
- If clk_rate is zero we return here. Therefore all further checks
in this function for clk_rate != 0 are not needed.
- switch from dev_warn to dev_err if the clock can't be set
- If due to clock source and available divider values the requested
frequency isn't matched exactly (always the case if requested
frequency is 52 MHz), then just print the differing values as
debug message and not as warning.
- Also remove ret from the message as it is always 0.
- Set member current_clock to the current requested rate and
mmc->actual_clock to the current actual rate
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
val isn't used in the switch clause and afterwards there's an
identical statement. So remove it.
In case of an unexpected bus width the error message indicates
the intention to set the bus width to 4 and to go on.
So remove the return statement. This return statement also
conflicts with "setting to 4" because nothing would be set
actually before returning. 4bit bus width are chosen as
default as the vendor driver does it too.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The current code dealing with calculating mmc->f_min is a bit complicated.
Additionally, the attempt to set an initial clock rate should explicitly
use a rate between 100KHz to 400 KHz, according the (e)MMC/SD specs, which
it doesn't.
Fix the problem and clean up the code by using clk_round_rate() to pick the
nearest minimum rate to 400KHz (rounded down from 400kHz).
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
[Heiner: Changed from 100KHz to 400KHz to get a proper rounded rate]
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Fixes: a45c6cb816 ("[ARM] 5369/1: omap mmc: Add new omap
hsmmc controller for 2430 and 34xx, v3")
when using really large timeout (up to 4*60*1000 ms for bkops)
there is a possibility of data overflow using
unsigned int so use 64 bit unsigned long long.
Signed-off-by: Ravikumar Kattekola <rk@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
commit e2bf08d643 ("omap_hsmmc: set a large data timeout for
commands with busy signal") sets an arbitrary timeout value (100ms) for
commands like CMD6 (MMC SWITCH). However extended CSD register defined
in the eMMC standard has a field for GENERIC_CMD6_TIME which indicates
the default maximum timeout for a SWITCH command.
Use busy_timeout of cmd structure (populated with GENERIC_CMD6_TIME
in the case of SWITCH command) to program the data timeout value in
omap_hsmmc driver.
SWITCH command to turn the cache on took more than 100ms to complete
with MICRON eMMC card present in AM572x IDK REV 1.3A resulting in
timeout and failed enumeration. It is fixed here by programming the
timeout with the value advertised in GENERIC_CMD6_TIME.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Ravikumar Kattekola <rk@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When CEB (command end bit error) occurs
reset CMD line to avoid system ending up in
erroneous state.
While command line is reset for CTO and CCRC errors,
it's not done for CEB error. Fix it here.
Reviewed-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Ravikumar Kattekola <rk@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When deploying runtime PM, it's quite verbose to print the
log of ios setting. Also it's useless to print it from system
PM as it should be the same with booting time. We also have
sysfs to get all these information from ios attribute, so let's
skip this print from PM context.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
commit 64b12a68a9
"mmc: core: fix prepared requests while doing bkops"
is fixing a bug in the wrong way. A bug in the MMCI
device driver is fixed by amending the MMC core.
Thinking about it: what the pre- and post-callbacks
are doing is to essentially map and unmap SG lists
for DMA transfers. Why would we not be able to do that
just because a BKOPS command is sent inbetween?
Having to unprepare/prepare the next asynchronous
request for DMA seems wrong.
Looking the backtrace in that commit we can see what
the real problem actually is:
mmci_data_irq() is calling mmci_dma_unmap() twice
which is goung to call arm_dma_unmap_sg() twice
and v7_dma_inv_range() twice for the same sglist
and that will crash.
This happens because a request is prepared, then
a BKOPS is sent. The IRQ completing the BKOPS command
goes through mmci_data_irq() and thinks that a DMA
operation has just been completed because
dma_inprogress() reports true. It then proceeds to
unmap the sglist.
But that was wrong! dma_inprogress() should NOT be
true because no DMA was actually in progress! We had
just prepared the sglist, and the DMA channel
dma_current has been configured, but NOT started!
Because of this, the sglist is already unmapped when
we get our actual data completion IRQ, and we are
unmapping the sglist once more, and we get this crash.
Therefore, we need to revert this solution pushing
the problem to the core and causing problems, and
instead augment the implementation such that
dma_inprogress() only reports true if some DMA has
actually been started.
After this we can keep the request prepared during the
BKOPS and we need not unprepare/reprepare it.
Fixes: 64b12a68a9 ("mmc: core: fix prepared requests while doing bkops")
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add a bit more debug messages that can be helpful when debugging the clock
setup.
Also fill the actual_clock field in struct mmc_host to report properly the
current frequency in debugfs.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The MMC2 controller on the A64 is kind of a special beast.
While the general controller design is the same than the other MMC
controllers in the SoC, it also has a bunch of features and changes that
prevent it to be driven in the same way.
It has for example a different bus width limit, a different maximum
frequency, and, for some reason, the maximum buffer size of a DMA
descriptor.
Add a new compatible specifically for this controller.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The A64 MMC controllers need DATA0 to be masked while updating the clock,
otherwise any subsequent command will result in a timeout.
It's not really clear at this point what DATA0 is exactly, but this
behaviour is present in Allwinner's tree, and has been suggested by
Allwinner engineers as fixes for the timeout.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The A64 MMC controllers need to set a "new timings" bit when a new rate is
set.
The actual meaning of that bit is not clear yet, but not setting it leads
to some corner-case issues, like the CMD53 failing, which is used to
implement SDIO packet aggregation.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Experience have shown that the using the autocalibration could severely
degrade the performances of the MMC bus.
Allwinner is using in its BSP a delay set to 0 for all the modes but HS400.
Remove the calibration code for now, and add comments to document our
findings.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The MMC core assumes that the code will gate the clock when the bus
frequency is set to 0, which we've been ignoring so far.
Handle that.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The SD specification documents that the clock frequency should only be
changed once gated (Section 3.2.3 - SD Clock Frequency Change Sequence).
The current code first modifies the parent clock, gates it and then
modifies the internal divider. This means that since the parent clock rate
might be changed, the bus clock might be changed as well before it is
gated, which breaks the specification.
Move the gating before the parent rate modification.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This removes CDC init sequence comments which are
not useful anyway.
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
platform_execute_tuning should not really exist as it does not
do anything useful.
So remove this ops and directly plug sdhci_msm_execute_tuning
with mmc_host_ops.
Also in case of HS400 tuning clear SDHCI_HS400_TUNING flag once
HS400 related mode selection is done.
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some controllers have 2 clock sources instead of 1. The 2nd clock
is for the internal card detect logic and must be enabled/disabled
along with the main core clock for proper operation.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Cleanup some debug prints that cause needless noise
during normal usage.
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use the bitops API instead of shifting directly.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Remove the sdhci-s3c-regs.h file.
Instead, it located those defined values into sdhci-s3c.c.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Before enabling SDIO irqs, clear the status bit, so we discard old and
stale interrupts. Needed to get two wireless cards working. Use the
newly introduced macro in all places.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
QUIRK sounds like there is something wrong, but actually there are just
some bits which need to be 1. Rename it to be more clear.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
tmio_mmc_sdio_irq() is not used as a seperate irq handler anymore, so we
can make it similar to the other irq helper functions, namely:
* only give the host as argument function which is what it really needs
* prefix function name with __
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Create a helper function to disable clocks and use it in remove(), too.
Now, clk_summary in debugfs reports the clocks as disabled and
unprepared after unbinding.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
